A library for manipulating NeoPixel RGB LEDs for the:

Particle Core, Photon, P1, Electron, Argon, Boron, Xenon and RedBear Duo

Implementation based on Adafruit's NeoPixel Library.

• 800 KHz WS2812, WS2812B, WS2813 and 400kHz bitstream and WS2811
• 800 KHz bitstream SK6812RGBW (NeoPixel RGBW pixel strips) (use 'SK6812RGBW' as PIXEL_TYPE)

The most common kinds are WS2812/WS2813 (6-pin part), WS2812B (4-pin part) and SK6812RGBW (3 colors + white).

• Radio Shack Tri-Color LED Strip with TM1803 controller 400kHz bitstream.
• TM1829 pixels, many details here.
• Some functions from the MessageTorch library have been added.
• SK6812MINI "NeoPixel Mini" (use 'WS2812B' as PIXEL_TYPE)

Set up the hardware:

• A NeoPixel digital RGB LED (get at adafruit.com)
• or a Radio Shack Tri-Color LED Strip (get at radioshack.com)
• A power supply or breakout board to supply NeoPixel's with 5V

Flash the rainbow example. With the Particle CLI do particle flash <my_device> examples/a-rainbow

Adapt it to your needs while keeping this general structure:

Adafruit_NeoPixel strip(PIXEL_COUNT, PIXEL_PIN, PIXEL_TYPE);
void setup() {
  strip.begin();
  strip.show();
}
void loop() {
  // change your pixel colors and call strip.show() again
}

// IMPORTANT: Set pixel COUNT, PIN and TYPE
#define PIXEL_COUNT 10
#define PIXEL_PIN D2
#define PIXEL_TYPE WS2812B
Adafruit_NeoPixel strip(PIXEL_COUNT, PIXEL_PIN, PIXEL_TYPE);

Creates an object to interact wth a NeoPixel strip.

PIXEL_COUNT is the number of pixels in strip.

Note: for some stripes like those with the TM1829, you need to count the number of segments, i.e. the number of controllers in your stripe, not the number of individual LEDs!

PIXEL_PIN is the pin number where your NeoPixel are connected (A0-A7, D0-D7, etc). If omitted, D2 is used.

On Photon, Electron, P1, Core and Duo, any pin can be used for Neopixel.

On the Argon, Boron and Xenon, only these pins can be used for Neopixel:

• D2, D3, A4, A5
• D4, D6, D7, D8
• A0, A1, A2, A3

In addition on the Argon/Boron/Xenon, only one pin per group can be used at a time. So it's OK to have one Adafruit_NeoPixel instance on pin D2 and another one on pin A2, but it's not possible to have one on pin A0 and another one on pin A1.

PIXEL_TYPE is the type of LED, one of WS2811, WS2812, WS2812B, WS2812B2, WS2813, TM1803, TM1829, SK6812RGBW. If omitted, WS2812B is used.

Note: For legacy 50us reset pulse timing on WS2812/WS2812B or WS2812B2, select WS2812B_FAST or WS2812B2_FAST respectively. Otherwise, 300us timing will be used.

Note: RGB order is automatically applied to WS2811, WS2812/WS2812B/WS2812B2/WS2813/TM1803 is GRB order.

strip.begin();

Sets up the pin used for the NeoPixel strip.

strip.setPixelColor(num, red, green, blue);
strip.setPixelColor(num, red, green, blue, white);
strip.setPixelColor(num, color);
strip.setColor(num, red, green, blue);
strip.setColor(num, red, green, blue, white);

Set the color of LED number num (0 to PIXEL_COUNT-1). red, green, blue, white are between 0 and 255. White is only used for RGBW type pixels. color is a color returned from Color.

The brightness set with setBrightness will modify the color before it is applied to the LED.

strip.show();

Displays the colors on the NeoPixel strip that were set with setPixelColor and other calls that change the color of LEDs.

This function takes some time to run (more time the more LEDs you have) and disables interrupts while running.

strip.clear();

Set all LED color to off. Will take effect on next show().

strip.setBrightness(brightness);

Make the LED less bright. brightness is from 0 (off) to 255 (max brightness) and defaults to 255.

This factor is not linear: 128 is not visibly half as bright as 255 but almost as bright.

uint8_t brightness = strip.getBrightness();

Get the current brightness.

strip.setColorScaled(num, red, green, blue, scaling);
strip.setColorScaled(num, red, green, blue, white, scaling);

Set the color of LED number num and scale that color non-linearly according to the scaling parameter (0 to 255).

strip.setColorDimmed(num, red, green, blue, brightness);
strip.setColorDimmed(num, red, green, blue, white, brightness);

Set the color of LED number num and dim that color linearly according to the brightness parameter (0 to 255). In this case 128 should look half as bright as 255.

uint32_t color = strip.Color(red, green, blue);
uint32_t color = strip.Color(red, green, blue, white);

Make a color from component colors. Useful if you want to store colors in a variable or pass them as function arguments.

uint32_t color = strip.getPixelColor();

Get the current color of an LED in the same format as Color.

strip.setPin(pinNumber);

Change the pin used for the NeoPixel strip.

strip.updateLength(n);

Change the number of LEDs in the NeoPixel strip.

uint8_t *pixels = strip.getPixels();

Get the raw color data for the LEDs.

uint16_t n = strip.getNumLeds();
uint16_t n = strip.numPixels();

Get the number of LEDs in the NeoPixel strip. numPixels is an alias for getNumLeds.

• Make sure get the # of pixels, pin number, type of pixels correct
• NeoPixels require 5V logic level inputs and the Spark Core and Photon only have 3.3V logic level digital outputs. Level shifting from 3.3V to 5V is necessary, the Particle Shield Shield has the TXB0108PWR 3.3V to 5V level shifter built in (but has been known to oscillate at 50MHz with wire length longer than 6"), alternatively you can wire up your own with a SN74HCT245N, or SN74HCT125N. These are rock solid.
• To reduce NeoPixel burnout risk, add 1000 uF capacitor across pixel power leads, add 300 - 500 Ohm resistor on first pixel's data input and minimize distance between device and first pixel. Avoid connecting on a live circuit. If you must, connect GND first.
• Don't use getPixelColor() to move pixel data around when you are also using setBrightness(). When the brightness is set, all setPixelColor() calls will end up scaling colors to dim them before they are stored in memory. When using getPixelColor() the stored dimmed color is rescaled back up to the original color. However, due to some loss of precision with the math, it is not possible to recreate this color data perfectly. This is especially true with low brightness values. If you get and set color data repeatedly with a dimmed pixel, it will eventually continue to decrease in value until it is equal to zero.
• When changing the brightness, always call setPixelColor() first with fresh un-dimmed color data, then call setBrightness(), and finally show().

• NeoPixel Guide: https://learn.adafruit.com/adafruit-neopixel-uberguide
• Quad Level Shifter IC: SN74ACHT125N (Adafruit)
• Quad Level Shifter IC: SN74HCT125N (Digikey)
• Quad Level Shifter IC: SN74AHCT125N (Digikey)

Copyright 2014-2018 Technobly, Julien Vanier, Cullen Shane, Phil Burgess

Released under the LGPL license