1N4001 THRU 1N4007
General Purpose Plastic Rectifier
DO-204AL (DO-41)
Reverse Voltage 50 to 1000 V Forward Current 1.0 A
1.0 (25.4) MIN. 0.107 (2.7) 0.080 (2.0) DIA.
Features
Plastic package has Underwriters Laboratories Flammability Classification 94V-0 Construction utilizes void-free molded plastic technique Low reverse leakage High forward surge capability High temperature soldering guaranteed: 250C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension
0.205 (5.2) 0.160 (4.1)
1.0 (25.4) MIN. 0.034 (0.86) 0.028 (0.71) DIA.
NOTE: Lead diameter is 0.026 (0.66)
Mechanical Data
Case: JEDEC DO-204AL, molded plastic body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.012 ounce, 0.3 gram
0.023 (0.58)
for suffix "E" part numbers
Dimensions in inches and (millimeters)
Maximum Ratings & Thermal Characteristics Ratings at 25C ambient temperature unless otherwise specified.
SYMBOLS 1N 4001 1N 4002 1N 4003 1N 4004 1N 4005 1N 4006 1N 4007 UNITS
*Maximum repetitive peak reverse voltage *Maximum RMS voltage *Maximum DC blocking voltage *Maximum average forward rectified current 0.375" (9.5mm) lead length at TA=75C *Peak forward surge current 8.3 ms single half sine-wave superimposed on rated load (JEDEC Method) TA=75C *Maximum full load reverse current full cycle average 0.375" (9.5mm) lead length at TL=75C Typical thermal resistance (NOTE 1) Maximum DC blocking voltage temperature *Operating junction and storage temperature range
VRRM VRMS VDC IF(AV) IFSM IR(AV) RJA RJL TA TJ, TSTG
50 35 50
100 70 100
200 140 200
400 280 400 1.0 30 30 50 25 +150 -50 to +175
600 420 600
800 560 800
1000 700 1000
V V V A A A C/W C C
Electrical Characteristics
Ratings at 25C ambient temperature unless otherwise specified.
SYMBOLS
1N 4001
1N 4002
1N 4003
1N 4004
1N 4005
1N 4006
1N 4007
UNITS
*Maximum instantaneous forward voltage at 1.0A *Maximum DC reverse current at rated DC blocking voltage Typical reverse recovery time at IFM=20mA, IRM=1mA (NOTE 2) Typical junction capacitance at 4.0V, 1MHz TA= 25C TA=100C
VF IR trr CJ
1.1 5.0 50 30 15
V A s pF
NOTES: (1) Thermal resistance from junction to ambient, and from junction to lead at 0.375 (9.5mm) lead length, P.C.B. mounted (2) Measured on Tektronix type S recovery plug-in. Tektronix 545 scope or equivalent. *JEDEC registered values
11/29/99
1N4001 THRU 1N4007
Ratings and Characteristic Curves (T
FIG.1 - FORWARD CURRENT DERATING CURVE AVERAGE FORWARD RECTIFIED CURRENT, AMPERES
A
= 25C unless otherwise noted) FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT
30
PEAK FORWARD SURGE CURRENT, AMPERES
1.0
60 HZ RESISTIVE OR INDUCTIVE LOAD
8.3ms SINGLE HALF SINE WAVE (JEDEC Method) TA=75C
0.8
0.2 x 0.2 (5.0 x 5.0mm) COPPER PADS
25
0.6
20
0.4
15
0.2
0.375 (9.5mm) LEAD LENGTH
10
5.0 0 25 50 75 100 125 150 175 1 10
NUMBER OF CYCLES AT 60 HZ
100
AMBIENT TEMPERATURE, C
FIG. 4 - TYPICAL REVERSE CHARACTERISTICS FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS FORWARD CURRENT, AMPERES INSTANTANEOUS REVERSE CURRENT, MICROAMPERES
1,000
20 10
TJ=25C PULSE WIDTH=300s 1% DUTY CYCLE
100
TJ=150C
10
TJ=100C
0.1
0.1
TJ=25C
0.01 0.6
0.8
1.0
1.2
1.4
1.6
1.8
INSTANTANEOUS FORWARD VOLTAGE, VOLTS
0.01 0
20
40
60
80
100
PERCENTAGE OF PEAK REVERSE VOLTAGE, %
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
100
TRANSIENT THERMAL IMPEDANCE, C/W
TJ=25C f=1.0 MHz Vsig=50mVp-p
FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE
100
JUNCTION CAPACITANCE, pF
10
10
1 0.1
10
100
REVERSE VOLTAGE, VOLTS
0.1 0.01
0.1
10
100
t, PULSE DURATION, sec.
