Scribd
Upload
243 views3 pages

ENodeB Commisioning Guide

1. The document provides instructions for commissioning an eNodeB using a USB disk. Files like the software package, license file, and data configuration file need to be copied to specific folders on the USB disk. 2. After powering off the BBU and connecting RRUs, the USB disk is inserted into the LMTP. Once power is turned back on, the LMTP will automatically detect the USB disk and download the necessary files. 3. The eNodeB may reset a few times during the software upgrade process. The USB disk should not be removed until normal eNodeB operation is confirmed.

Uploaded by

Katsaras Stelios
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
243 views3 pages

ENodeB Commisioning Guide

1. The document provides instructions for commissioning an eNodeB using a USB disk. Files like the software package, license file, and data configuration file need to be copied to specific folders on the USB disk. 2. After powering off the BBU and connecting RRUs, the USB disk is inserted into the LMTP. Once power is turned back on, the LMTP will automatically detect the USB disk and download the necessary files. 3. The eNodeB may reset a few times during the software upgrade process. The USB disk should not be removed until normal eNodeB operation is confirmed.

Uploaded by

Katsaras Stelios
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd

COMMISSIONING WITH USB DISK

1. Copy the .xml of the specific eNodeB inside the USB folder \eNodeB\,
and make sure it is named [Link]
File
eNodeB software package
License file
Data configuration file

Specified File Path in the USB Storage Device


usb:\eNodeB\Software\
usb:\eNodeB\License\
usb:\eNodeB\[Link]

2. POWER OFF BBU and connect RRUs to the BBU


3. Insert the USB disk to LMTP as below:

4. POWER ON BBU and check the status after some seconds:


Indicator on
the USB
Automatically detecting the USB storage
device
Downloading software and data
configuration file

Steady on

RUN indicator on the


LMPT
Blinking
(on for 1s and off for 1s)
Blinking

Blinking

Activating software and data configuration


file

(on for 0.125s and off for


0.125s)
Blinking

Steady on

Normal eNodeB operation

Steady on

(on for 0.125s and off for


0.125s)
Blinking
(on for 1s and off for 1s)

5. The eNodeB may reset few times during software upgrade. Do NOT
REMOVE the USB until confirming the eNodeB normal operation.

CONNECTING TO LMT FOR TROUBLESHOOTING

1. Copy the software to this Laptop PC directory: C:\


V100R003C00SPC480\
2. Connect laptop to ETH Port of LMPT
3. Manually configure the following IP to the Laptop: [Link] /
[Link]
4. Open Internet Explorer and go to web page [Link]
5. Username: admin / Password: admin123
6. After WebLMT opens, click the button Download FTP Tool to download and run the
[Link] the

icon must appear in the status area of Windows taskbar.

7. Run any of the below commands to perform the relevant action. Change
the Laptop IP or directory accordingly:

Load XML (rename the .xml in laptop to [Link]):


DLD CFGFILE: MODE=IPV4, IP="[Link]", USR="admin", PWD="admin", DIR="C:\",
FN="[Link]";
ACT CFGFILE: EFT=IMMEDIATELY;

Install Software:
DLD SOFTWARE: MODE=IPV4, IP="[Link]", USR="admin", PWD="admin",
DIR="C:\V100R003C00SPC480\", DL=NO;
ACT SOFTWARE: OT=NE, SV=" V100R003C00SPC480";

Supply Software (if not all commands appear in WebLMT):


SPL SOFTWARE: MODE=IPV4, IP="[Link]", USR="admin", PWD="admin", DIR="
C:\V100R003C00SPC480\", ", SDL=YES;

PERFORMING TEST CALLS


1. Force the DATACARD to LTE or 4G ONLY
2. Ask NMC to activate the cells one by one
3. Enable the DATA connection to LTE (Connect)
4. Check that the LTE signal is full or confirm with NMC that the correct
cell is used
5. Go to [Link] and perform a download test. The throughput
must be more than 5 Mbps DL / 1 Mbps UL.
6. Take a print screen for each cell and name it accordingly.

You might also like