BATTERY TECHNOLOGYContents
Introduction to batteries
Basic concepts
Battery characteristics
Classification, Dry cell, Li-CuS cell, Lead-acid, Nicad- &
lithium ion batteries
Fuel cells, Construction & working of alkaline FC, proton
exchange membrane FC & direct methanol FC
Learning objectives
Demonstrate an understanding of the meaning of the terms
cell, battery, charging, recharging, separator, fuel cell.
Describe construction & working of some battery systems &
fuel cells.
Distinguish between primary & secondary battery types.
Explain the effect of overcharging lead acid battery
Make accurate qualitative statements about battery systems
Identify the advantages & disadvantages of typical battery
systems.
Terms
Cell
Battery
Charging
Discharging
Separator
Fuel cell
Cycle life
Shelf
Design life
Voltage
Current
Capacity
Electricity storage density
Power
Capacity: The capacity is the charge or the amount of electricity that
may be obtained from the battery and is given in ampere hours (Ah).
Capacity = I x t
Where I = Current
t= time
Electricity storage density: Electrical storage density is the amount of
electricity per unit weight which the storer can hold, its the capacity
per unit weight of the battery.
Power (Watts): The electric power P is equal to the energy
consumption E divided by the consumption time t:
P is the electric power in watt (W).
E is the energy consumption in joule (J).
t is the time in seconds (s).
Power (Watts) = EI, Where E = Voltage, I = Current
Shelf life: Time an inactive battery can be stored before it becomes
unusable i.e,the length of time a battery can remain without losing its
Classification & comparison of commercial
cells Differences & similarities
Primary Batteries
Secondary Batteries
[Link] reaction is irreversible
Cell reaction is reversible
2. Must be discarded after its
active
elements
have
been
consumed
3. Have relatively short shelf life
4. Function only as galvanic cells
May be recharged a number of
times from an external d.c. source
during its useful life
Have very long shelf life
Function as galvanic cells during
discharge as & as electrolytic cells
5. Cannot be used as energy during charging process.
storage devices
Can be used as energy storage
devices (e.g. solar/ thermal energy
converted to electrical energy)
6. Cannot be recharged
Can be recharged.
e.g. Dry cell, Li-MnO2 battery
[Link] acid battery, Ni-cd battery
Basic requirements of cells
Primary cell
Compact, light weight &
fabricated easily
High energy density &
constant voltage
Benign environmental
properties
Longer shelf life &
discharge period
Leak proof containers &
variety of design options.
Economically priced
Secondary cell
Long shelf-life in both
charged & discharged
conditions
Longer cycle life & design
life
High power to weight ratio
Short time for recharge.
High voltage & high
energy density
Dry cell
Working: Primary Reactions:
Anode:
Zn(s)
Zn2+ (aq) +2e_
Cathode: 2MnO2(s) + H2O (l) + 2e- Mn2O3(s) + 2OH-(aq)
Net Reaction:
Zn(s) + 2MnO2(s) + H2O (l) Zn2+(aq) +Mn2O3 (s)+ 2OH-(aq)
Secondary Reactions:
NH4+(aq) + OH(aq) NH3(g) + H2O (l)
Zn2+(aq) + 2NH3(g)+ 2 Cl [Zn(NH3)2 Cl2]
Cell Reaction: Zn + 2MnO2 + NH4Cl [Zn(NH3)2 Cl2] + H2O
+ Mn2O3
Dry cell
Advantages
Disadvantages
Cheap
Voltage
drop
when
High energy density.
current is drawn rapidly
Not toxic
from it
Contains
electrolytes.
no
liquid Limited shelf life
Cannot be used once they
get discharged.
Emf decreases during use
Lithium/copper sulfide cell
Construction
Anode: Lithium
Cathode: Copper sulphide.
Electrolyte: mixture of 1,2-dimethoxyethane, 1,3-
dioxolane and 3,5-dimethylisoxazole as a stabilizer
with LiClO4 solute.
OR
Tetrahydrofuran (THF) and dimethoxyethane (DME)
binary solvent with LiClO4 for the solute
O.C.V. = 1.7 V
Working
Anode reaction:
Cathode reaction:
LixCuS
x Li
x Li+ + x e-
CuS + xLi+ + xe-
On continued discharge, the second step of the
cathode discharge occurs:
2LixCuS + 4e-
2LixCu + 2S2-
Lead Storage Battery
Effect of overcharging
2H2O (l) + electrical energy 2H2 (g) + O2(g)
Consequences:
(i)Reduce the acid level and damage the exposed electrode grids
(ii)Dangerous high-pressure build-up that can lead to a serious
risk of explosion.
Modern maintenance-free batteries
Modern maintenance-free batteries:
without a gas release vent. Gassing is controlled by using
1. Pb-Ca (0.1 % ) as the anode which inhibits the electrolysis
of water.
2. a catalyst (e.g. a mixture of 98% ceria (cerium oxide) & 2%
platinum) that combines the hydrogen & oxygen produced
during discharge back into water
Lead Storage Battery
Advantages
Disadvantages
highly efficient
good service for
several years
low internal self
discharge
provide a large
current
Sulfation
low energy storage to weight ratio
CP decreases with decrease in conc. of
sulfuric acid
not efficient at LT
Overcharging may damage the exposed
electrodes & may also lead to
explosion in extreme cases
Sulfuric acid is highly corrosive liquid
Lead is toxic & hence environmental &
health problems
corrosion of the lead grid at the lead
dioxide electrode
Nickel Cadmium Cell
Nickel Cadmium Cell
Disadvantages
Advantages
Long cycle life
Constant voltage
Long shelf life
No gassing
Long design life
Good performance at LT
Produce large
instantaneous currents
Environmental
pollution hazard
Increased weight
High overall capital
cost
KOH is a corrosive
hazardous chemical
Lithium ion cells
At anode:LixC6 xLi+(solv) + 6C(s) + ne-.(1)
At cathode:CoO2(s)+ xLi+(solv) + ne- LixCoO2(s) (2)
Net cell reaction:LixC6 (s) + CoO2
Discharge
Charge
LixCoO2(s)+ 6C.(3)
Lithium - ion Cell
Advantages
Designed to overcome the
safety problems
Long cycle life
Small, light & provide high
energy density
Can be operated in a wide
temperature range
High average voltage
Disadvantages
Poor charge retention
Self discharge rate is
about 10% per month
High cost
Fuel cells
Alkaline fuel cell
Alkaline fuel cell
Advantages
Active O2 electrode
kinetics
Flexible to a wide
range of electrocatalysts
Disadvantages
1. Electrolyte
sensitive to CO2
2. Reformer with a
highly effective
CO & CO2
removal system
Direct Methanol fuel cell
DMFC
Advantages
Liquid fuel, MeOH can be
easily transported, stored &
dispensed
Methanol is stable in
contact with the acidic
membrane
Fuel is cheap & available in
large quantities
Combustion products can
be removed easily
No production of NOx
gases
Disadvantages
o Anodic & cathodic reaction
has poor electrode kinetics
o Crossover of fuel
o Methanol is toxic
Proton exchange membrane fuel cell
Role
F
of
proton
F
conducting
F
O
F
O=S=O
O
membranes
+
H
PEMFC
Advantages
Solid electrolyte
resists gas crossover
Low operating
temperature
Provides high
current density
Disadvantages
Thermal management
difficult
Optimized proton &
water transport
properties of the
membrane & proper
water management are
crucial
Sensitive to poisoning
High cost
Fuel cell
Differences -Similarities
Do not store chemical energy
Reactants fed from outside the cell
continuously
Need expensive noble metal catalysts
& optimum operative conditions
Do not get discharged & no need of
charging
Never become dead as long as fresh
reactants are available
Useful for long-term electricity
generation.
Reaction
products
must
be
continuously removed
No pollutants generated Produce
power from fuels
Significantly higher power densities
Galvanic Cell
Store chemical energy
Reactants from an integral
part of its construction.
These special conditions are
not required
Get-discharged when stored
up energy is exhausted.
Limited life span in use
Useful as portable power
services.
No such problem
Pollutants are generated after
their useful life
They cannot generate
electricity from fuels
Lower power density
Summary
Battery - device consisting of several galvanic cells
that convert stored CE into EE.
Batteries primary or secondary types.
The construction, working & applications of
conventional dry cell, lead acid battery, nicad cell,
lithium copper sulfide cell have been discussed .
Fuel cell - converts the CE from a fuel into EE by
oxidation process.
Fuel cells require a constant source of fuel &
oxygen /air to sustain the oxidation reaction.
Self-test
What is the purpose of separator in a commercial cell?
What are the disadvantages of Nicad over lead acid battery?
What are the basic commercial requirements for a primary &
secondary cell?
Distinguish between the following;
i) Cell & battery ii) Charging & discharging
Write the anode active material & cathode active material in
the following cells; 1) Dry cell 2) lead acid cell 3) Nicad cell
Give reason: a) Combustion of a gaseous fuel gives thermal
energy where as the oxidation of the fuel in a fuel cell gives
electrical energy b) In principle, secondary battery should
have unlimited life, but in practice is has limited life. c) The
lead acid cell doesnt need to have separate anode & cathode
compartments
