Scribd
Upload
15K views2 pages

MCQ

This document contains a quiz on metal forming and casting processes. It asks 10 multiple choice questions about processes like cold working, forging, casting defects, and terms used in casting. It also includes 6 true/false statements about topics like mechanical working, casting defects, mold types, extrusion processes, and sand permeability. The document provides the questions along with the answers key at the end.

Uploaded by

RAMAKANT RANA
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
15K views2 pages

MCQ

This document contains a quiz on metal forming and casting processes. It asks 10 multiple choice questions about processes like cold working, forging, casting defects, and terms used in casting. It also includes 6 true/false statements about topics like mechanical working, casting defects, mold types, extrusion processes, and sand permeability. The document provides the questions along with the answers key at the end.

Uploaded by

RAMAKANT RANA
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

Manufacturing Process MAIT

METAL FORMING AND CASTING PROCESS


Pick out the most appropriate option:
1. Advantage of cold working is
(a) better dimensional accuracy (b) better surface finish
(c) higher strength (d) all of these.
2. Typical hot working temperature range for steel is
(a) 650–1050°C (b) 650–723°C
(c) 500–910°C (d) none of these.
3. The forging operation of “upsetting” is
(a) reverse of drawing down process (b) it is a bending operation
(c) it is a drifting operation (d ) none of these.
4. “Alligatoring” is a defect associated with
(a) forging process (b) casting process
(c) extrusion process (d) rolling process.
5. A “die” is used in
(a) casting process (b) extrusion process
(c) forging process (d) all of these.
6. Out of the following, which is the defect which is not associated with casting process:
(a) Blow holes (b) Scale
(c) Centre burst (d) Hot tear.
7. Which “term” is not associated with casting process?
(a) Gate (b) Runner (c) Riser (d) Swage.
8. Fuel used in a cupola consists of
(a) steam coal (b) furnace oil (c) electricity (d) hard coke.
9. Which allowance is not provided on the “pattern” made for a casting ?
(a) Machining allowance (b) Solidification allowance
(c) Draft allowance (d) Shrinkage allowance.
10. “Blanking” is an expression used in
(a) sheet metal work (b) casting process
(c) drawing (d) rolling.

Indicate, if following statements are True or False:

1. Mechanical working processes result information of grain-flow lines which reduces the
strength of parts.
2. “Blow hole” and shrinkage cavities occur in [Link] factors which cause these defects
are similar in nature.
3. Sand mould is an example of permanent mould.
4. Mismatch is shift of the individual parts of a casting with respect to each other.
5. Hooker extrusion is a cold extrusion process.
6. The permeability of fine grained moulding sand will be more.

BY- RAMAKANT RANA


Manufacturing Process MAIT

ANSWERS
1. (d)
2. (a)
3. (a)
4. (d )
5. (d)
6. (c)
7. (d )
8. (d )
9. (b)
10. (a)

1. F
2. F
3. F
4. T
5. T
6. F

BY- RAMAKANT RANA

You might also like