ROUTING DINAMIC
OSPF Area 0
Routing Dinamis OSPF
Routing dinamis ini termasuk dalam kategori Link State, dimana perhitungan jalur
terbaik berdasarkan banyaknya router yang dilewati atau perhitungan bandwidth jalur.
Mengkonfigurasikan routing OSPF cukup mendaftarkan network address yang terhubung
secara langsung beserta wildcard mask dan nantinya akan di tukarkan tabel routing ke
tetangga untuk mengupdate / memperkenalkan network address.
Berikut step – step konfigurasi setiap roter :
R1 :
R1>en
R1#conf t
R1(config)#router ospf 10
R1(config-router)#network [Link] [Link] area 0
R1(config-router)#network [Link] [Link] area 0
R1(config-router)#network [Link] [Link] area 0
R2 :
R2>en
R2#conf t
R2(config)#router ospf 5
R2(config-router)#network [Link] [Link] area 0
R2(config-router)#network [Link] [Link] area 0
R2(config-router)#network [Link] [Link] area 0
R3 :
R3>en
R3#conf t
R3(config)#router ospf 15
R3(config-router)#network [Link] [Link] area 0
R3(config-router)#network [Link] [Link] area 0
R3(config-router)#network [Link] [Link] area 0
Routing table
R1 :
R1#sh ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter
area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
[Link]/30 is subnetted, 3 subnets
C [Link] is directly connected, Serial2/0
O [Link] [110/1562] via [Link], [Link], Serial2/0
[110/1562] via [Link], [Link], Serial3/0
C [Link] is directly connected, Serial3/0
C [Link]/24 is directly connected, FastEthernet0/0
O [Link]/24 [110/782] via [Link], [Link], Serial2/0
O [Link]/24 [110/782] via [Link], [Link], Serial3/0
R2 :
R2#sh ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter
area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
[Link]/30 is subnetted, 3 subnets
C [Link] is directly connected, Serial2/0
C [Link] is directly connected, Serial3/0
O [Link] [110/1562] via [Link], [Link], Serial2/0
[110/1562] via [Link], [Link], Serial3/0
O [Link]/24 [110/782] via [Link], [Link], Serial2/0
C [Link]/24 is directly connected, FastEthernet0/0
O [Link]/24 [110/782] via [Link], [Link], Serial3/0
R3 :
R3#sh ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter
area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
[Link]/30 is subnetted, 3 subnets
O [Link] [110/1562] via [Link], [Link], Serial3/0
[110/1562] via [Link], [Link], Serial2/0
C [Link] is directly connected, Serial3/0
C [Link] is directly connected, Serial2/0
O [Link]/24 [110/782] via [Link], [Link], Serial2/0
O [Link]/24 [110/782] via [Link], [Link], Serial3/0
C [Link]/24 is directly connected, FastEthernet0/0
Testing koneksi (PING)
R1 PC 2 :
R1#ping [Link]
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to [Link], timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 46/68/93 ms
R1 PC 3 :
R1#ping [Link]
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to [Link], timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 78/103/125 ms
R3 PC1 :
R3#ping [Link]
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to [Link], timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 62/84/110 ms
R3 PC2 :
R3#ping [Link]
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to [Link], timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 78/97/125 ms
