Scribd
Upload
186 views3 pages

Consistent Deformation Derivation Guide

The document defines consistent deformation as a process that determines structural deformations that satisfy compatibility requirements. It involves two main steps: 1) removing redundant forces to create a determinate structure, and 2) applying forces at the removed locations to return the structure to its original position. An example of applying this to a propped cantilever beam under uniform load is provided. Key aspects of the consistent deformation solution procedure are outlined, including developing displacement terms and setting up a system of compatibility equations to solve for redundant forces.

Uploaded by

Adi Deck
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
186 views3 pages

Consistent Deformation Derivation Guide

The document defines consistent deformation as a process that determines structural deformations that satisfy compatibility requirements. It involves two main steps: 1) removing redundant forces to create a determinate structure, and 2) applying forces at the removed locations to return the structure to its original position. An example of applying this to a propped cantilever beam under uniform load is provided. Key aspects of the consistent deformation solution procedure are outlined, including developing displacement terms and setting up a system of compatibility equations to solve for redundant forces.

Uploaded by

Adi Deck
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

Consistent Deformations Derivation

Objectives:
1.
2.

Define consistent deformation variables


State consistent deformation procedure steps

Consistent deformations is based on compatibility. Compatibility states that a structure can


deform in any shape provided the displacements conform to the boundary conditions and the
material restrictions (i.e. the material can not tear apart).

Consistent deformations process:


$
$

Remove all the redundant reactions and forces (i.e. add hinges) until it becomes
determinate.
Then apply forces at the removed redundants to put the structure back into a
compatible displacement.

Example, take the uniformly loaded propped cantilever beam.


One redundant (or extra) support.
1.
Remove the prop or end support we have a cantilever beam.
2.
Apply a force at the point where the support was removed.
3.
Need to calculate the force needed to push the tip back up to the support.

The tip deflection under uniform load is:

Consistent Deformation Derivation - Page 1 of 3

wL
r 10 =
8EI

The tip deflection due to a unit force at the end of the beam:

L
f 11 =
3EI
Apply a tip force equal to the ratio of the deflection without the prop to that of the unit force.
4

wL
8EI
R prop = 3
L
3EI

Definitions:
ri

is the final displacement at removed redundant i. This is usually zero but can also be
a final support displacement such as a support settlement.

ris

is the displacement at redundant i on the determinate base structure due to settlement


of the supports. This is only a rigid body displacement and only requires geometry to
calculate.

rit

is the displacement at redundant i on the determinate base structure due to temperature.

rie

is the displacement at redundant i on the determinate base structure due to initial


imperfections.

ri0

is the displacement at redundant i on the determinate base structure due to the applied
loading.
Consistent Deformation Derivation - Page 2 of 3

fij

is the displacement at redundant i on the determinate base structure due to a unit force
at redundant j.

Xj

is the unknown redundant force at redundant j. This can be a support reaction or an


internal force like a moment or an axial force.

The second index refers to the load applied that caused the deflection.

Consistent Deformation Solution Procedure


1)

Remove all redundant forces to form a determinate base structure. This can involve
removing supports, adding hinges or cutting members. The choice of which forces to
remove is arbitrary, however clever choices can make the calculations simpler.

2)

Calculate the displacements at each of the removed redundants due to all the applied
loading. This should include loads, temperature and settlement. Each type of loading
is considered to be its own load case. Therefore, applied loads are considered as load
case 0. Temperature is considered as load case t, etc.

3)

Apply a unit force at each redundant, one at a time, and find the displacements at all of
the other removed redundants. Each redundant creates a separate load case, designated as
load case j, where j corresponds to the redundant at which the load is applied. This will
develop the terms fij. The applied unit load is at redundant j. The calculated
displacements are at all other redundants i. Each load case will fill out a column of the F
matrix. Applying the unit load at another redundant will develop another column of the F
matrix.

4)

Apply the compatibility equation:

all redundants

r i = r is + r it + r ie + r i 0 +

f ij X j

There is one compatibility equation for each removed redundant. This will create a set of
simultaneous equations with Xj's as the unknowns. Solving the set of equations gives the values
for the removed redundant forces.

Consistent Deformation Derivation - Page 3 of 3

You might also like