Standard Accessories
Install software and driver
Leaper-48 main unit x1, USB cable x1, DC 12V/2A adaptor x1,
Operation software CD-ROM x1, Quick User Guide x1
Main unit
Adaptor
USB cable
Introduction
Unit top view
Unit back view
Power led
Power switch
USB port (B type)
48Pin Textool
Action led
Textool handle
IC package
diagram
1. Set Font Size to [small fonts] (96 dpi) to have the optimal display.
1.1 Click the right button on the desktop. -> Select the [Properties] in the
bottom of the function menu.
1.2 Select [Settings] and then click the [Advanced] to set Font Size.
2. Install the software before connecting the Leaper-48 to the PC.
2.1 Insert the software CD into your CD-ROM drive. Auto Run start-up
installation. Follow the instructions to complete installation.
2.2 If Auto Run doesn't work, click [[Link]] in the CD directory to install.
3. Install the driver of Leaper-48 hardware.
3.1 Make sure the Leaper-48 power is [OFF]. Connect the power adaptor to
the Leaper-48. Plug in and then turn on the power. The green led on the
adaptor and power led on the programmer panel will be lit on.
3.2 Link the USB cable to PC USB port and programmer USB port.
3.3 After assembling the USB cable and the power adaptor, Windows will
auto start-up [Found New Hardware Wizard].
3.4 Install Hardware Device Driver
-> Search for a suitable driver for my device(recommended)
3.5 Locate driver files Optional search locations
-> CD-ROM driver
3.6 Driver Files Search Result
-> Windows found a driver for this device....\driver\[Link]
3.7 Completing the Found New Hardware Wizard
DC 12V input socket
Attention
1. It is preferred to use an internal USB port of your PC. External USB
ports are not recommended because of shared bandwidth and
possible compatibility issues of other USB devices.
2. When you use special socket adapters (PLCC, TSOP, SOP...), Please
pull the textool up to 80 . Put the special socket adapter in the
textool and then pull the handle down to fix the socket adapter.
[3.3]
[3.4]
[3.5]
LEAP Electronic Co., Ltd.
Tel : + 886-2-2999 1860
Fax : + 886-2-2999 9873
http ://[Link]
Email: service@[Link]
[3.6]
* Above installation is described in Windows 2000 *
[3.7]
Options
Parameters
[Link] device split function
[Link]-low voltage verify
[Link]-check on device
( i.e. pin scan, IC identify... )
Device DC/AC parameter settings
[Link] information
*only enabled when programmer
is turned on and connected to
the PC
2. Sound settings
Device settings
*only enabled when programmer
is turned on and connected to
the PC
Programming source
Load from PC
Select IC number
IC type
Programmer self-test
*only enabled when programmer
is turned on and connected to
the PC
*Remove any device from the
ZIF socket, if present.
Verify source IC
Save file
Read from
source IC
Exit program
Edit file
Save file
Source filename
IC manufacturer, type
number and package
Load file
Device verify
Check SUM
Programming status
Process option
Device pin
check
Signal light
Re-scan
Ignore signal
Counter
Clear counter
Run
Progress
percentage
Stop
Erase
Blank
check
Program
Verify
Program process & options
Protect /
security
Auto loop
Cancel
Instruction
Source file editing
8bits HEX display
16bits HEX display
Project
Buffer & file information
Description
of Project
IC number,
manufacturer
& package
Auto Run:
Once: Single program
Multi: Loop program
NO: Manual program
Protect lock:
Undeletable
Address of data
Click and enter
new address.
HEX code Display
Click to enter
hexadecimal data.
Select project
ASCII code Display
Click to enter text.
Exit edit window
Double click to run the project.
Single click to select the project.
Click right button to display properties
of the project. Double click blank
row to create a new project.
Create new project
Delete
project
Create new project with present settings.
Only reserve for 10 records. Or the project
keeper will delete the un-protect and
former file (on the top row).
Hot Key
Confirm changes
Cancel changes
Set data block
range by
load file size
Get data block
checksum
*When a Microchip
PIC device is selected,
IC checksum will be
shown directly.
Data block Move/Copy/Swap
Data block - Fill
Set data block
range by
selected IC size
Set data block range
by maximum size of
buffer
Click [Space] bar in the main operation screen
to pop Hot Key menu.
Execute
Project
How to create a project
How to program an IC
Step 1 Select IC number
Step 1 Create a Project
Step 1 Execute Project
[Link] [Type] icon.
[Link] IC manufacturer.
[Link] IC number.
[Link] [OK] Button.
[Link] [Project] icon.
[Link] [Create] button
to start up the project
editing window./
Double click blank
column to create a
new project.
[Link] project
description.
[Link] [Auto loop]
parameter: Once/
Batch/Manual.
[Link] [Project Protect]
to protect project.
[Link] [OK] to save the
project or click
[Cancel] to discard
any changes.
[Link] [Project] icon.
[Link] click to run project
or click right button to check
the properties of the project.
Double click blank
column to create
a new project.
Step 2 Get source data
Mode 1: Load from file
[Link] [Load] icon.
[Link] [Browse] to load file.
[Link] file format.
[Link] [Load] button to read data.
Mode 2: Read from source IC
[Link] source IC.
[Link] [Read] icon.
>Start to read and verify IC.
[Link] status and checksum
Step 2 Program IC
Method1: One time auto-program
[Link] target IC.
>Process IC with project options.
[Link] process status.
Step 3 Program IC
Description
of Project
IC number,
manufacturer
& package
Auto Run:
Single program
Place target IC
Mode 1:Program single IC
[Link] process options.
[Link] target IC.
[Link] [Run] icon.
>Process IC with selected options.
[Link] process status.
Process option
Run
Method 2: Loop auto-program
[Link] target IC.
>Process IC with project options.
[Link] process status.
[Link] above steps for the next IC.
[Link] [Cancel] botton to stop programming.
Mode 2: Program batch of ICs
[Link] process option.
[Link] target IC.
[Link] [Auto Loop] icon.
>Process IC with selected options.
Auto Loop
[Link] process status.
>Waiting for placement of the next target IC.
[Link] above steps for the next IC.
[Link] [Cancel] icon on Scan IC Window to stop process.
Click to ignore
the IC check
and process
the next IC
Place Target IC
Project created
date and time
Auto Run:
Loop program
Programming Process
E: Erase IC, C: Blank check,
P: Program IC, V: Verify IC,
S: Protect/Security
Click to ignore
the IC check
and process
the next IC
Protect lock:
Undeletable
Place target IC
Replace target IC
Check IC location
and pin status
Click to stop
the batch
programming
Replace target IC
Method 3: Manual program
[Link] target IC
[Link] [Run] icon.
>Process IC with project options.
[Link] process status.
Click to stop
the batchprogram
Check IC pins
and location
Run
