10/27/2016
Hydraulic Engineering
CEWB222
CHAPTER 2
(OPEN CHANNEL PROPERTIES)
Dr. Gasim Hayder Ahmed Salih
BN-3-49, [email protected]
Sources: Dr. Faizah Che Ros, Dr. Mohd Hafiz Zawawi, Prof Ir. Dr. Lariyah Mohd Sidek
Types of open channel
Natural channel
All watercourses that occurs naturally, for example streams
and rivers
The Hydraulic properties are generally irregular
Not regular nor prismatic and their materials of construction
can vary widely.
The surface roughness will often change with time distance
and even elevation.
10/27/2016
Types of open channel
Man-made channel
Constructed in a regular cross-section shape throughout and thus
are PRISMATIC CHANNELS.
Made from concrete, steel or earth with well defined surface
roughness.
All watercourses that are constructed by human effort, for
example :
Types of open channel
Canal : a long and mild-sloped channel built in the ground that
may be unlined or lined with stone masonry, concrete ,etc.
Flume : a channel of concrete, masonry, etc that is usually
supported on or above the surface of the ground to convey
water across a depression.
Chute : a channel with steep slopes.
Culvert : a covered channel of comparatively short length
installed to drain water through highway and railroad
embankments.
10/27/2016
Canal
Rigid Boundary Canal
Trunk Drain - Wet Period
10/27/2016
FLUME
Existing Culvert
10/27/2016
Existing Pipe Culvert
Existing Box Culvert
10/27/2016
Channel Geometry
Prismatic channel : a channel with
unvarying cross section and constant
bottom slope.
Non-prismatic channel : a channel
with varying cross section and
constant bottom slope.
CHANNEL GEOMETRY
10/27/2016
Properties and geometric elements of typical
channel cross section
Rectangular
Area,
A
Wetted
perimeter,
P
by
b + 2y
Hydraulic
Radius,
R
Top Width, B
by / (b+2y)
Hydraulic
depth,
D
y
Properties and geometric elements of typical
channel cross section
Trapezoidal
Area,
A
Wetted
perimeter,
P
b + 2yw
(b + ty)y w= (1+ t2)0.5
Hydraulic
Hydraulic
Radius, Top Width,
depth,
R
B
D
A/P
b + 2ty
A/B
10/27/2016
Properties and geometric elements of typical
channel cross section
Triangular
Wetted
Area, A perimeter, P
ty2
2yw
Hydraulic Top Width, Hydraulic
Radius, R
B
depth, D
ty / (2w)
2ty
A/B
Properties and geometric elements of typical
channel cross section
Circular
Area, A
Wetted
perimeter, P
Hydraulic
Radius, R
Top Width,
B
Hydraulic
depth, D
( - sin ) d2/8
(1 - sin/)
d/4
2r sin(/2)
A/B
10/27/2016
Properties and geometric elements of typical
channel cross section
Semi circular
Area, A
Wetted
perimeter, P
Hydraulic
Radius, R
Top Width,
B
Hydraulic
depth, D
r2/2
r/2
2r
r/4
Properties and geometric elements of typical
channel cross section
10/27/2016
RECTANGULAR CHANNEL
Area (A) = by
T
Wetted perimeter (P) = b+2y
y
Hydraulic Radius (R) = A/P=
by
b 2y
Top width (T) = b
Hydraulic Depth (D) = y
TRAPEZOIDAL CHANNEL
Area = (b+zy)y
2
P = b 2y 1 z
T
1
y
z
R=
(b zy) y
b 2 y 1 z2
T = b 2 zy
D=
(b zy) y
b 2 zy
10
10/27/2016
Example 1
A concrete rectangular channel has a bottom
width of 4 meters. If the channel is on a 1%
slope and is flowing 1 meter deep throughout its
length, what is the cross sectional area, wetted
perimeter and hydraulic radius?
Solution:
If the shape of the channel is rectangular, the
discharge computed as follows:
A = by = (4) (1) = 4m2
P = b+2y = 4 + 2 (1) = 6m
R = 4m2 / 6m = 0.67m
T
1
11
10/27/2016
Example 2
A concrete trapezoidal channel has a bottom width of 4
meters and 45 side slopes. If the channel is on a 1%
slope and is flowing 1 meter deep throughout its
length, what is the cross sectional area, wetted
perimeter and hydraulic radius?
Example 2
1
T
1
1
Solution:
If the shape of the channel is trapezoidal, the discharge
computed as follows:
A = (b+zy)y = (4+(1)(1))1 = 5.00m2
P = (b+ 2y (1+ z2)0.5 )= 4 + 2 (1) (2)0.5 = 6.83m
R = A/P = 5.00m2/6.83m = 0.73m
12
10/27/2016
Example 3
Water flows at a depth of 1.83 m in a trapezoidal, concretelined section with a bottom width of 3 m and side slopes of
2:1 (H:V). The slope of the channel is 0.0005 and the
temperature is 20o C. Assuming uniform flow conditions,
estimate the cross sectional area (A), wetted perimeter (P)
and hydraulic radius (R)?
Solution:
Flow area, A = (b+zy)y = (3 + 2 (1.83)) x 1.83
= 12.2 m2
Wetted perimeter, P = 14.89m
Hydraulic Radius, R = A/P = 12.2/ 14.89 = 0.819 m
13
10/27/2016
Example 4
14
10/27/2016
TEXTBOOKS REFERENCES
Lariyah, M.S. & Norazli, O., Hydraulic Notes,
UNITEN, 2006
Roberson, J. A., Cassidy, J. J. & Chaudry, H.,
Hydraulic Engineering, 1st S.I. Ed., John
Wiley, 1998
Chin, D., Water Resources Engineering,
Prentice Hall, 2006
15
