CQE Training & Consultancy (IP 0187064-K)
Registered Office : No. 46, Lorong Bintang, Taman Tasik Permai, 34000 Taiping, Perak. Malaysia.
Operating Office : No. 85A (1st. Floor), Jalan Barrack, 34000 Taiping, Perak. Malaysia.
T : +605-805 2722 / +605-808 8028 F : +605-805 2721 M : +6012-505 2720
E : [email protected] or [email protected] W : http://www.cqetraining.com B : http://cqeblog.blogspot.com
PROCESS VALIDATION TRAINING (PVT)
(PUBLIC / IN-HOUSE TRAINING PROGRAMME)
SBL
Introduction Scheme
With today shorter Design and Development Cycle requirements, Process Validation (PV) requirements are
specified by general management system standards, as well as legal and regulations. Process Validation can
be varies from retrospective, concurrent or prospective validation as an evidence of conduct, compliance to
the general management system standards, legal and regulations requirements.
This course provides an introductory understanding of Process Validation for general management system
standards and regulations requirements including ISO 9001, ISO 13485, ISO/TS 16949, AS 9100, ISO 17025,
ISO 22000 etc, and overview on practical statistical methodologies for its analysis and guidance for its
planning, implementation and maintenance. Process Validation varies from Design Qualification, Installation
Qualification, Operational Qualification and Performance Qualification will be discussed during the training
session.
The training content is easy-to-understand and are suitable for companies complying with general
management systems standards, legal and regulatory.
Objective
To provide delegates with proven practices and techniques that lead to Process Validation (PV) related to the
Design & Development Processes:
An introduction to the fundamentals and basic principles of process validation.
An awareness of the international standard and regulatory requirements for Process Validation.
Explaining how, when, where and why you should validate.
Implementation and documentation guide.
Statistical methods and tools used in Process Validation.
To address on how to maintain adequate validation documentation systems and perform equipment
qualifications, process validations.
Prepared by : Mr . Eddie Kuang Copyright 2001-2015. All Rights Reserved. -1-
CQE Training & Consultancy (IP 0187064-K)
Registered Office : No. 46, Lorong Bintang, Taman Tasik Permai, 34000 Taiping, Perak. Malaysia.
Operating Office : No. 85A (1st. Floor), Jalan Barrack, 34000 Taiping, Perak. Malaysia.
T : +605-805 2722 / +605-808 8028 F : +605-805 2721 M : +6012-505 2720
E :
[email protected] or
[email protected] W : http://www.cqetraining.com B : http://cqeblog.blogspot.com
Program Contents
Day 1
Introduction to Process Validation
o Basic Principles of Process Validation
o Regulatory and International standard Requirements for Validation (ISO 9001, ISO 13485, ISO/TS 16949,
AS 9100, ISO 22000 etc)
Overview of Process Validation
o Why and What do we validate
o Design Qualification
o Installation Qualification
o Operational Qualification
o Performance Qualification
o Process Validation Decision
o Validation Master Plan
o Protocols and reports
Planning the Process Validation
o Establish validation team
o Develop Master Validation Plan
o Review Planning
o Develop validation protocol
Conducting and Executing the Process Validation
o Determination of WHAT to verify / measure
o Determination of HOW to verify / measure
o Determination of HOW MANY to verify / measure
o Define acceptance / rejection criteria
o Consideration during IQ / OQ / PQ
o Reporting
Maintaining Validation
o Monitor and control of Process Validation
o Changes of processes and / or product
o Periodic Revalidation
o Use of historical Data in process validation
Statistical methods and tools for Process Validation
o Introduction of the statistical methods and tools
o Descriptions and Objectives of the statistical methods and tools
o Application of the statistical methods and tools
Examples
Prepared by : Mr . Eddie Kuang Copyright 2001-2015. All Rights Reserved. -2-
CQE Training & Consultancy (IP 0187064-K)
Registered Office : No. 46, Lorong Bintang, Taman Tasik Permai, 34000 Taiping, Perak. Malaysia.
Operating Office : No. 85A (1st. Floor), Jalan Barrack, 34000 Taiping, Perak. Malaysia.
T : +605-805 2722 / +605-808 8028 F : +605-805 2721 M : +6012-505 2720
E :
[email protected] or
[email protected] W : http://www.cqetraining.com B : http://cqeblog.blogspot.com
Who Should Attend
This programme is suitable for all levels of personnel involved with the process validation activities from
planning, executing, reporting, reviewing, approving and maintaining the process validation.
The delegate may be someone new to process validation and aims to have a better understanding on the
overall process validation activities.
Duration
1 Day
Training Methodology
The program would be conducted by using the following materials / aids :-
Course Note
OHP / LCD
Group Activities
Lecturettes
Prepared by : Mr . Eddie Kuang Copyright 2001-2015. All Rights Reserved. -3-
CQE Training & Consultancy (IP 0187064-K)
Registered Office : No. 46, Lorong Bintang, Taman Tasik Permai, 34000 Taiping, Perak. Malaysia.
Operating Office : No. 85A (1st. Floor), Jalan Barrack, 34000 Taiping, Perak. Malaysia.
T : +605-805 2722 / +605-808 8028 F : +605-805 2721 M : +6012-505 2720
E :
[email protected] or
[email protected] W : http://www.cqetraining.com B : http://cqeblog.blogspot.com
Prepared by : Mr . Eddie Kuang Copyright 2001-2015. All Rights Reserved. -4-
