1.

How many minimum numbers of 3-line-to-8-line decoders are

required for a 5-of-32 decoder?
1. 8

2. 2

3.5
4. 1

2. gain in dBi is with reference to

1. isotropic
2. hertzian dipole

3. dipole

4. milliwatt power

3. If the flux density is 10 Wb/ m2 and the area of the coil is 2m2,
the flux is
1. 1 Wb

2. 20 Wb
3. 10 Wb

4. 40 Wb

4. A current of 4 A flows in an AC circuit when 100 V DC is applied to

it whereas it takes 250 V AC to produce the same current the
power factor of the circuit is
1. 0.8

2.

0.6

3.
0.4
4.
1

5. Information rate basically gives an idea about the generated

information per _____ by source
1. Hour

2. Distance

3. Second
4. Minute

6. A comparison between ring and johnson counters indicates that:

1. a Johnson counter has an inverted feedback path
2. a ring counter has an inverted feedback path

3. a Johnson counter has fewer flip-flops but requires more decoding circuitry

4. a ring counter has fewer flip-flops but requires more decoding circuitry

7. A MOD-12 and a MOD-10 counter are cascaded. Determine the

output frequency if the input clock frequency is 60 MHz?
1. 2000kHz

2. 1500kHz

3. 500kHz
4. 1000kHz

8. A ripple counter’s speed is limited by the propagation delay of:

1. each flip-flop
2. all flip-flops and gates

3. the flip-flops only with gates

4. only circuit gates

 9. A signal m(t) = 10cos(2π100t) undergoes frequency modulates a
carrier. The resulting FM signal is x(t) = 20cos(2π106t +
15sin(2π100t)). The approximate bandwidth of the FM used be
1. 3.2 kHz

2. 10 KHz
3. 1 kHz

4. 100kHz

10. Design procedure of combinational circuit which gives output

high if the input is greater than 5 involves minimum of ................
gates
1.One AND and one OR gate
2.Two AND and one OR gate

3.One AND and two OR gate

4.One AND gate

11. For an AC circuit, if v(t) = 160 sin (ω t+ 10°) v and i(t) = 5 sin
(ωt - 20 °) A; then reactive power absorbed by the circuit is
1.

100 VARS.

2.
200 VARS.
3. 400 VARS.

4.

300 VARS.
 12. How many 3-to-8 line decoders with an enable input are
needed to construct a 6-to-64 line decoder without using any
other logic gates?
1. 7

2. 8

3. 9
4. 10

13. How many flip-flops are required to make a MOD-29 binary

counter?
1. 3

2. 6

3. 5
4. 4

14. If a noiseless channel bandlimited to 5 kHz is sampled every

1msec, what will be the value of sampling frequency?
1. 500 samples/sec

2. 800 samples/sec

3. 1000 samples/sec
4. 250 samples/sec

15. Which of the following best describes how to construct a 1-

line to 8-line de-multiplexer from a 3-line to 8-line decoder:

1.

Connect the decoder input select lines CBA to D

2.connect the select lines of de-mux CBA as input D for decoder and input of de-mux as enable input for
decoder 3. Connect the decoder input data lines to Di
4. Connect the decoder output to Di

16. If the transfer function of a first-order system

isG(s)=1/(1+2s),then the time constant of the system is

1.

10 seconds.

2. 0.1second.

3. 2 seconds.
4. 0.5second.

17. . In 8051, what indicates when EA is connected to ground?

1. Program code is stored in on-chip RAM

2. DATA is stored in on-chip RAM

3. Program code is stored in external ROM

4. Program code is stored in on-chip ROM

18. . Which one of the following is an example of open-loop

system?

1. Air conditioner
2. Light switch
3. Automatic electric iron

4. Water level controller

19. 1 kW carrier is modulated to a length of 60%. The total

power in the modulated carrier is
1. 1.06 KW

2. 1KW

3. 1.6 KW

4. 1.18 KW

20. 2’s complement representation of a 16 bit number (one sign

bit and 15 magnitude bits) is FFFF. Its magnitude in decimal
representation is
1. 1
2. 65535

3. 32767

4. 0

21. G wireless data network uses

1.no switching

2. Both Circuit and Packet Switched

3. Circuit Switched

4. Packet Switched
 22. ______ denotes the traffic intensity the entire trunked radio
system.
1. Grade of Service

2. Load
3. Traffic intensity

4.quality of Service

23. _________ is a subscriber module that stores all the

subscriber related information.
1. BSS

2. MS

3. ME

4. SIM

24. ____________ is the expansion of GPRS.

1. General packet radio Switching

2. Genuine packet radio System

3. General packet radio service

4. Genuine packet radio switching

25. ______________ is defined as the frequency at which the

magnitude of a circuit response function is reduced to 1/√2 times
its maximum value
1.Cut-off Frequency
2. Critical Frequency

3.Power frequency

4. Resonant Frequency
 26. _______________ is the constant change of the range of the
geographical area covered by a cellular telephone transmitter
based on the amount of traffic currently using that transmitter.
1. Cell loading factor

2. Sectorization

3. FER

4. Cell breathing

27. _________________ and _______________________

equations are necessary in a communication system to calculate
the ratio between the Rx power and TX power.
1. ampere, Helmholtz

2. Maxwell, faraday

3. Nyquist, sampling

4. Friss, radar range

28. A 2 port network using Z parameter representation is said to

be reciprocal if

1.
Z12 = Z21
2.

Z11 = Z22

3.

Z12 = –Z21

4. Z11Z22 – Z12Z21 = 1
 29. A 4-bit up/down binary counter is in the DOWN mode and in
the 1100 state. To what state does the counter go on the next
clock pulse?
1. 1101

2. 1011
3. 1111

4. 0000

30. A 60kHz carrier is amplitude modulated by the speech band

of 300 to 3000 Hz. The range of upper side band will be
1. 57 to 59.7 kHz

2. 60 to 59.7 kHz

3. 60.3 to 63 kHz
4. 56.7 to 56.3 kHz

31. A ________ filter significantly attenuates all frequencies

below fc and passes all frequencies above fc.
1. high-pass
2. band-stop

3. band-pass

4. low-pass

32. A balanced 3 - Φ star connected load is fed from a 208 V, 3 -

Φ supply. Each load has resistance of 35 Ω. The total power is

1.
1236 W.
2.

618 W.

3.

411.3 W.

4.309 W

33. A balanced delta connected load has an impedance of 9∠ 30°

Ω per phase. What is the impedance per phase of its equivalent
star?

1.

1∠ 90° Ω.

2.
3∠ 30° Ω.

3.

28∠ 30° Ω.

4.

27∠ 90° Ω.
 34. A band pass signal extends from 1KHz to 2 KHz. The minimum
sampling frequency needed to retain all information in the
sampled signal is
1. 2 KHz
2. 1 KHz

3. 4 KHz

4. 3 KHz

35. A BJT is said to be operating in the saturation region, if

1. Base emitter junction is in forward biased, and base collector junction is reverse biased

2. Both the junctions are forward biased

3. Base emitter junction is in reverse biased, and base collector junction is forward biased

4. Both the junctions are reverse biased

36. A capacitor circuit does not allow to

pass________component.
1. d.c.
2. current

3. a.c.

4. voltage

37. A carrier is amplitude modulation to depth of 40%. The

increase in power is

1.

40 %
2. 20 %

3. 8%
4.

16 %

38. A carrier is simultaneously modulated by two sine waves with

modulation indices of 0.4 and 0.3.
1. 1.0

2. 0.35

3. 0.5
4. 0.7

39. A CDMA system is designed based on DS spread spectrum

with a processing gain of 1000 and BPSK modulation scheme. If
user has equal power and the desired level of performance of an
error probability of 10^-6, the number of user will be
1. 117

2. 147

3. 216

4. 89

40. A certain CE amplifier has a voltage gain of 100. If the emitter

bypass capacitor is removed
1. The Q-point will shift

2. The circuit will become unstable

3. The voltage gain will decrease

4. The voltage gain will increase
 41. A certain inverting amplifier has a closed-loop voltage gain of
25. The Op-amp has an open-loop voltage gain of 100,000. If an
Op-amp with an open-loop voltage gain of 200,000 is substituted
in the arrangement, the closed-loop gain ……..
1.
remains at 25

2.

drops to 12.5

3.

doubles

4.

increases slightly

42. A circuit which has ω0 = 106 rad / sec (ω0 = resonant

frequency) C = 10 pF and Q = 100, must have a resistance of
___________ kΩ.

1.

2. 1

3.

10
4.
100

43. A circuit with resistor, inductor, and capacitor in series is

resonant frequency of 50 Hz. If all the values are now doubled, the
new resonant frequency is

1.
f0 / 2

2. Still f0.

3.

f0 / 4.

4.

2f0.

44. A Closed- loop system is unstable if

1. Gain margin is negative and phase margin is positive

2. Both gain margin and Phase margin are negative

3. Gain margin is positive and phase margin is negative

4. Both gain and phase margin are positive

45. A collector characteristic curve is a graph showing ____

1. emitter current (IE) versus collector-emitter voltage (VCE) with (VBB) base bias voltage held
constant
2. collector current (IC) versus collector-emitter voltage (VC) with (VBB) base bias voltage held
constant

3. collector current (IC) versus collector-emitter voltage (VCC) with (VBB) base bias voltage held
constant

4. collector current (IC) versus collector-emitter voltage (VCE) with (VBB) base bias
voltage held constant

46. A combinational logic circuit which generates a particular

binary word or number is
1. Multiplexer

2. Decoder
3. Date Selector

4. Data Distributor

47. A communication channel distributed by additive white

Gaussian noise has a bandwidth of 4 kHz and SNR of 15. The
highest transmission rate that such a channel can support (in k-
bits/sec) is
1. 16
2. 1.6

3. 3.2

4. 60

48. A communication channel with additive white Gaussian

noise, has a bandwidth of 4 kHz and an SNR of 15, its channel
capacity is
1. 32kbps

2. 16kbps
3. 256kbps

4. 20kbps
 49. A deterministic signal has
1. completely specified function of time
2. uncertainity

3. no uncertainity 4.Definite Certainity

50. A dielectric material must be

1. semi conductor

2. insulator
3. resistor

4. good conductor

51. A digital-to-analog converter is an application of the

1. adjustable bandwidth circuit

2. voltage-to-current converter

3. noninverting amplifier

4. scaling adder

52. A direct sequence spread binary phase-shift keying system

uses a feedback shift register of Length 19 for the generation of PN
sequence. The system is required to have an average probability of
symbol error due to externally generated interfering signals that
does not exceed 10 -5. The Anti-jam margin is
1. 12.6 dB

2. 47.5 dB

3. 93.8 dB

4. 86.9 dB

53. A distortion less line has

1. Constant imag characteristic impedance

2. vanishing attenuation constant

3. Constant velocity
4.high G

54. A FM signal has a carrier swing of 100 kHz when the

modulating signal has a frequency of 8 kHz. The modulation index
is
1. 6.25

2. 12.5
3. 7.5

4. 15

55. A frequency multiplier using PLL has VCO output frequency f0

is given by
1. fs/N

2. fs

3. Nfs
4. 1/Nfs

56. A line is excited by a 100 V dc source. If reflection coefficients

at both ends are 1 each then
1. there will be only 1 or 2 oscillations on line

2. the oscillations will continue indefinitely

3. there will be a finite number of oscillations on line

4. there will be no oscillations on line

57. A log amplifier may use the ________ junction of a BJT in the
feedback loop.
1. base-collector

2. emitter-collector

3. base-emitter
4. emitter-ground
 58. A long transmission line is energized at then sending end and
is kept open circuited at the receiving end. The magnitudes of the
sending end voltage Vs and of the receiving end voltage Vr satisfy
the following relationship:
1. Vs is greater than Vr

2. Vs is less than Vr

3.0

4. Vs =Vr

59. A low pass filter circuit is basically

1. Integrator with larger time constant
2. Integrator with low time constant

3. Differentiator with low time constant

4. Differentiator with larger time constant

60. A LTI system is said to be initially relaxed system only if ____

1. zero input produces non-zero output

2. zero input produces zero output

3.Zero input produces infinite output

4. zero input produces an output equal to unity

61. A MOD-16 ripple counter is holding the count 10012. What

will the count be after 31 clock pulses?
1. 1000
2. 1010

3. 1001

4. 1011
 62. A multiple access technique used in GSM cellular system.

1.
TDMA
2.

FDMA

3.

CDMA

4. TACS

63. A parallel plate capacitor of 5pf capacitance has a charge of

0.1µC on its plates. What is the energy stored in the Capacitor?
1. 1mJ
2. 1 nJ

3. 1pJ

4. 1µJ

64. A PN sequence generator using feedback shift register of

length,m=4. Chip rate is 10M chips per second. Determine the PN
sequence length.
1. 16

2. 12

3. 20

4. 15

65. A point charge, Q = 10nC is at the origin. The estimated

potential difference at A (1,0,0) with respect to B (2,0,0) is
1.
45 V
2. 50 V

3.

30 V

4. -45 V

66. A pole of the transfer function generates the form of the

1.
forced response

2.

natural response

3.Both natural and forced response

4.

Exponential Response

67. A practical DC current source provides 20 kW to a 50 Ω load

and 20 kW to a 200 Ω load. The maximum power that can draw
from it is
1. 22.5 kW
2. 30.3 kW

3. 40 kW

4. 45 kW

68. A quarter wave line open circuited at far end behaves as

1. Inductance
2. L and C in series
3. Capacitance

4. L and C in parallel

69. A rate ½ convolution code with dfrec = 10 is used to encode a

data requeence occurring at a rate of 1 kbps. The modulation is
binary PSK. The DS spread spectrum sequence has a chip rate of 10
MHz. The coding gain is
1. 7 dB
2. 12 dB

3. 14 dB

4. 24 dB

70. A reactance having an inductor of 0.15 H is connected in

series with 10 Ω resistances. What will be the inductive reactance?

1.
47.1 Ω

2.

1.5 Ω

3.

10 Ω

4.

48.15 Ω
 71. A receiver is operated at a temperature of 300 K. The
transistor used in the receiver has an average output resistance of
1 kΩ. The Johnson noise voltage for a receiver with a bandwidth of
200 kHz is
1. 1.8 µV
2. 12.6 µV

3. 4.3 µV

4. 0.8 µV

72. A ring oscillator consisting of 5 inverters is running at a

frequency of 1MHz.The propagation delay of each inverter is
………………nsec
1. 200

2. 400

3. 50

4. 100

73. A series circuit consists of R = 20 Ω, L = 20 mH, and AC supply

60 V with f = 100 Hz. The current in R is

1.

5.08 A

2. 10.16 A 3. 1.27 A

4.
2.54 A
 74. A series resonant circuit and a parallel resonant circuit are
equivalent if
1. Rp = Rs(1 + Q1) and Xp = Xs(1 + Q−1)

2. Rp = Rs(1 + Q3) and Xp = Xs(1 + Q−3)

3. Rp = Rs(1 + Q2) and Xp = Xs(1 + Q−2)

4. Rp = Rs(1 - Q2) and Xp = Xs(1 - Q−2)

75. A short circuit has a ________ drop across its terminals, and
the current is limited only by the surrounding network.
1. 5V

2. 0V
3. Infinity

4. 1V

76. A silicon PN junction is forward biased with a constant

current at room temperature. When the temperature is increased
by 10oC, the forward bias voltage across the PN junction
1. Increases by 60 mV

2. Decreases by 60 mV

3. Increases by 25 mV

4. Decreases by 25 mV

77. A sinusoidal 400 Hz modulating signal of 2V amplitude

frequency modulates a carrier and produces 70 kHz frequency
deviation. The frequency sensitivity is given by
1. 35 kHz/V
2. 70 kHz/V

3.

140 kHz/V
4.

72 kHz/V

78. A super heterodyne receiver with an IF of 450KHz is tuned to

a signal at 1200KHz. The image frequency is
1. 750 KHz

2. 900 KHz

3. 2100 KHz
4. 1650 KHz

79. A system has a receiver noise resistance of 50 ohm. It is

connected to an antenna with an input resistance of 50 ohm. The
noise figure of the system is

1. 101

2. 2

3.

4.
50

80. A T-section low pass filter has series inductor 80 mH and

shunt capacitance 0.022μF. What is the cut-off frequency?

1. 8 kHz.
2.

7.8 kHz.

3.
7.58 kHz.

4.

7 kHz.

81. A TDM link has 20 signal channels and each channel is

sampled 8000 times/sec. Each sample is represented by seven
binary bits and contains an additional bit for synchronization, the
total bit rate for the TDM link is
1. 1180 kbps

2. 1280 kbps
3. 1280 Mbps

4. 1180 Mbps

82. A transistor may be used as a switching device or as a ______

1. fixed resistor

2. variable resistor
3. tuning device

4. rectifier

83. A triangular-wave oscillator can consist of an op-amp

comparator, followed by __________
1. integrator
2. amplifier

3. differentiator

4. multivibrator
 84. A two-port is described by the following equations: V1 = 50I1
+ 10I2, V2 = 30I1+20I2 then which of the following is not true?

1. B = 50
2. h12 = 0.5

3.

Z12 = 10

4.

y12 = −0.0143

85. A Zener diode when used in voltage stabilization circuits, is

biased in
1. Forward bias region

2. Forward bias constant current mode

3. Reverse breakdown region

4. Reverse bias region below the breakdown voltage

86. A zero-level detector is a

1. limiter

2. comparator with a sine-wave output

3.

peak detector
4.
comparator with a trip point referenced to zero

87. AC load line is also known as ________

1. dynamic load line
2. quiescent load line

3. variable load line

4. active load line

88. Adaptive equalization is used to combat the effect of

1. Improper synchronization

2. Distortions due to jitter

3. Channel noise and Intersymbol interference

4. Phase distortion

89. ADSL Stands for

1. Asymmetric data subscriber loop

2. .Asymmetric data subscriber line

3. Asymmetric digital subscriber loop

4. Asymmetric digital subscriber line

90. Advantage of Manchester Coding

1. Low bandwidth

2. Ternary signaling

3. Most of power lies between DC and bit rate

4. No DC component

91. Amplitude modulation is the process of

1. frequency shift and phase shift
2. superimposing a low frequency on a high frequency
3. superimposing a high frequency on a low frequency

4. carrier interruption

92. Amplitude modulation is used for broadcasting because

1. it is more noise immune than other modulation system

2. compared with other system it requires less transmitting power

3. its use avoids receiver complexity

4. no other modulation system can provide the necessary bandwidth for high fidelity

93. An additive white Gaussian process X(t) is passed through an

ideal bandpass filter of center frequency 100 MHz and bandwidth
2 MHz. Let X(t) have a power spectral density of N0/2 and the
output of BPF is P(t). The variance of P(t) is
1. 106 N0

2. 2 x 106 N0
3. N0

4. N0/2

94. An electric potential field is produced in air by point charges

1µc and 4µc located at (-2,1,5) and (1,3,1) respectively. The energy
stored in the field is
1. 2.57mJ

2. 5.14mJ
3. 10.28mJ

4. 12.5mJ

95. An example of temporal speech coder is

1. Model based coding

2. Subband coding

3. Differential PCM
4. Adaptive transform coding
 96. An FM station is operating at 100 MHz. Maximum frequency
deviation is 75 kHz. If the highest modulating frequency is limited
to 15 kHz, find the modulation index and approximate bandwidth
required by the system?
1. 10, 180kHz

2. 10, 150kHz

3. 5, 180kHz
4. 5, 150kHz

97. An FM wave uses a 2 - 5V 1500Hz modulating frequency and

has a modulation index of 10. The deviation is
1. 2500Hz

2. 1250Hz

3. 1000Hz

4. 5000Hz

98. An important impairment to digital signals in a

communication system is the irregularities in timing caused by
imperfections in clock extraction and waveform regeneration. This
effect is known as
1. Fading

2. Aliasing

3. Attenuation

4. Jitter

99. An increase in the base recombination of a BJT will increase

1. the unity-gain cut-off frequency fT

2. the common emitter dc current gain β

3. the transconductance gm
4. the breakdown voltage BVCEO

100. An infinite length of uniform line charge has ρl = 10pC/m and

it lies along the z axis. Determine the electric field E at (4, 3, 3)

1.

1.8 aρmV/m

2.
180 aρmV/m

3. 18 aρmV/m

4. 280 aρmV/m

101. An LTI system with impulse response, h(n) = (-a)nu(n) and –a

< -1 will be,
1. unstable system

2. stable system

3. anticausal system

4. neither stable nor causal

102. An op-amp integrator has a square-wave input. The output

should be
1. a triangle wave.
2. a square wave.

3. pure dc
4. a sine wave.

103. An RLC circuit has a resonance frequency of 160 kHz and a Q-

factor of 100. Its band width is

1.32 MHz

2.16 MHz

3.
1.6 kHz.

4.

0.625 kHz.

104. Another name for a unity gain amplifier is

1. Integrator

2. Inverting Amplifier

3. Differentiator

4. Voltage follower

105. Antipodal signals differ in phase by

1. 90 degree

2. zero degree

3. 180 degree
4. 45 degree

106. Any function whose Fourier transform is zero for frequencies

outside finite interval is called
1. High pass function

2. Low pass function

3. Band limited function
4. Band pass function

107. Arrange the following in chronological order

a)Alec Reeves invention of PCM

b)Shannon’s Mathematical theroy of Communication

c)D.O.North’s Matched Filter

d)Harry Nyquist’s theory of Signal transmission in telegraphy

1. dacb
2. dbac

3. abcd

4. cdab

108. As reverse bias voltage is increased, for a diode, the base

width at the junction
1.fluctuating

2. increases
3. decreases

4. remains same

109. Bandwidth of broad band antennas is

1. infinity

2. 10:1 ratio

3. 0:1 ratio
4. 2:1 ratio

110. Bit-addressable memory locations are:

1. 20H through 2FH

2. 30H through 3FH

3. 40H through 4FH

4. 10H through 1FH

111. Block calls held condition specified the held probability at a

time period equal to an average holding time.
1.

Erlang C

2. Erlang B

a) Erlang B

b) Erlang C

c) Erlang D

d) D. Poisson

3.

Erlang D

4. Poisson

112. Both ε0 and χe are dimensionless: The statement is

________ and ______ respectively

1. True and True

2. False and True
3. True and False

4. False and False

113. Boundary conditions for normal component in

magnetostatic field is

1. B1n X B2n=0
2.

B1n /B2n

3. B1n=B2n

4.

B1n+B2n

114. By cascading LPF and HPF active filter, the resulting circuit is

1.LPF

2.HPF

3. BPF
4. narrow BSF

115. Cable modem is capable of delivering up to

1. 56 kbps

2. 30-40 mbps

3. 2 mbps
4. 256 kbps
 116. Change in value of common mode input signal in differential
pair amplifier make

1. Change in voltage across collector

2. Slight change in collector voltage

3. Emitterr voltage decreases to zero

4. Collector voltage decreases to zero

117. Choose the function f(t), -∞<t<+∞, for which a Fourier series
cannot be defined
1. 4 cos(20t+3)+3 sin(10t)

2. exp(-|t|)sin(25t)
3. 3 sin(25t)

4. 1

118. Code conversion circuits mostly uses

1.
AND-OR gates

2. AND gates

3. OR gates

4. XOR gates

119. Companding is used

1. In PCM transmitters, to allow amplitude limiting in receivers

2. To overcome quantizing noise

3. To protect small signals in PCM from quantizing distortion
4. To overcome impulse noise

120. Compensating networks are used in op-amp to

1. worsen the stability

2. decrease the gain

3. increase the BW

4. improve the stability

121. Consider a linear delta modulator system designed to

accomdate a sinusoid of amplitude 1V, frequency 800Hz.Sampling
rate is 64kHz. Minimum value of step size to avoid overload is
1. 75.5mV

2. 60.5mV

3. 70.5mV

4. 78.5mV

122. Consider a repetition code where code words are formed by

repeating each bit five times. Suppose we receive the following
bitstream.
0000011110000111111011000111001111000001
If we assume that we can both detect and correct errors, what was
the original bit stream?
1. 01010110
2. 11010110

3. 01010111

4. 01010100
 123. Consider a repetition code where code words are formed by
repeating each bit five times. Suppose we wish to detect and
correct errors in each received code word. What is the maximum
number of bit errors that we can correct?
1. 4

2. 3

3. 2
4. 1

124. Consider a repetition code where code words are formed by

repeating each bit five times. What is the minimum Hamming
distance for this code?
1. 1

2. 4

3. 5
4. 3

125. Consider a system that uses 8-bit ASCII codes to encode

letters. How long will it take to transmit the bit sequence encoding
“Good Morning” (not including quotation marks) if we use a bit
time of 4 samples per bit, and transmit samples at a rate of 1MHz?
Represent the answer in micro seconds.
1. 384
2. 484

3. 300

4. 458

126. Consider the assertions related to decoding process of cyclic

code. Which among the following is a correct sequence of steps
necessary for the correction of errors?
A. Syndrome determination after the division of r(x) & g(x)

B. Addition of error pattern to received code word

C. Selection of error pattern corresponding to the syndrome

D. Preparation of table comprising error patterns and syndromes

1. D,A,C,B
2. C,B,D,A

3. B,A,D,C

4. A,B,C,D

127. Continuous functions are sampled to form a

1. Digital image
2. Fast Fourier series

3. Fourier transform

4. Fourier series

128. Convert BCD 0001 0111 to binary.

1. 10010

2. 11000

3. 10001
4. 10101

129. Damped sinusoids are _____

1. sinusoid signals multiplied by growing exponentials

2. sinusoid signals divided by decaying exponentials

3. sinusoid signals divided by growing exponentials

4. sinusoid signals multiplied by decaying exponentials

130. Depth of penetration in free space is

1. 0

2. small

3. 1/α
4. Infinity

131. Determine odd parity for each of the following data words:
1011101;11110111; 1001101
1. P = 1, P = 1, P = 0

2. P = 0, P = 0, P = 1
3. P = 0, P = 0, P = 0

4. P = 1, P = 1, P = 1

132. Determine the output voltage when V1 = –V2 = 1 V.

1. 2V

2. –2 V
3. 1V

4. 0V
 133. Differential coding produces an output in which the
information is contained in differences between successive bits
such that the output changes state if the input bit is a 1 otherwise
the output remains the same. Assuming the initial condition for
the output is 0, the differential coding for the input sequence
1100101 is
1. 1000110
2. 1100100

3. 1011101

4. 1010101

134. Displacement of various sinusoids with respect to their origin

is
1. ac component

2. dc component

3. phase
4. vector

135. Divergence theorem is applicable for a ____ that is bounded

by a ________.
1. surface volume

2. line, surface

3. volume, surface
4. surface, line

136. Diversity technique is a method for improving which of the

following message signal by utilizing two or more communication
channels with different characteristics?
1. All are Correct

2. Reliability
3. Error detection capability
4. Error correction capability

137. Double-sided phase & amplitude spectra _____

1. Possess an odd & even symmetry respectively
2. Both possess an odd symmetry

3. Both possess an even symmetry

4. Possess an even & odd symmetry respectively

138. DSLAM stands for

1.DSL available multiplexer

2. DSL asynchronous multiplexer

3. DSL access multiplexer

4. DSL asymmetric multiplexer

139. Duality Theorem / Property of Fourier Transform states that

_________
1. Shape of signal in time domain & shape of spectrum can never be interchangeable

2. Shape of signal in frequency domain & shape of spectrum can never be interchangeable

3. Shape of signal in time domain & shape of spectrum can be interchangeable

4. Shape of signal in frequency domain & shape of spectrum can be interchangeable

140. dy(t)/dt + 2ty(t) = t2 x(t) is for a

1. linear, time varying, dynamic system

2. linear system

3. linear, time varying, static system

4. non-linear system

141. Dynamic RAM consumes ________ Power and ________

then the Static RAM
1.

less, faster
2.

more, faster

3.
less, slower
4.

more, slower

142. Effect caused by under sampling is called

1. aliasing
2. summation

3. sharpening

4. smoothing

143. Electric displacement is a______quantity.

1.curl

2. vector
3. scalar

4. divergenceless

144. Electric Flux inside a conducting sphere is

1. maximum

2. zero
3. uniform

4. minimum

145. Faraday’s law is valid for both open and closed loops. The
Lenz’s law is valid for
1. both open and closed loop

2. Only open loop

3. only closed loop.
4. neither open loop nor closed loop

146. Final value of X(s) = 1/(s-2) is

1. 1

2. 0

3. 2

4. Infinity

147. Find the value of Quantization noise in Watts, in a Pulse code

modulation system when a signal of 0-16 volts amplitude is
quantized using 3-bit quantization.
1. ¼

2. 1/12

3. 1/6

4. 1/3

148. For a (6,4) block code where n = 6, k = 4 and dmin = 3, how

many errors can be corrected by this code?
1. 1
2. 2

3. 0

4. 3

149. For a (8, 4 ,3) block code, which one of the following
statements is incorrect?
1. The code rate is 0.5

2. Each codeword contains 4 message bits

3. We can detect and correct 1 bit errors

4. We can detect 3 bit errors

150. For a 4-bit twisted ring counter, the maximum no of states

possible are:
1. 4

2. 2

3. 8
4. 16

151. For a 8-bit ring counter, the maximum no of states possible

are :
1. 16

2. 8

3. 4
4. 2

152. For a BJT, the common base current gain α = 0.98 and the
collector base junction reverse bias saturation current, ICO = 0.6
µA. This BJT is connected in the common emitter mode and
operated in the active region with a base current (IB) of 20 µA. The
collector current IC for this mode of operation is
1. 0.98 mA

2. 0.99 mA

3. 1.01 mA
4. 1.0 mA

153. For a transmitted signal of unknown phase, which of the

following receiver is used to get maximum SNR?
1. Envelope Detector

2. Correlator
3. Matched Filter
4. Coherent detector

154. For an AM signal the bandwidth is 20 kHz and the highest

frequency component present is 800kHz.The carrier frequency
used for this AM signal is.
1. 790kHz
2. 710kHz

3. 700kHz

4. 705kHz

155. For an electromagnetic wave incident on a conducting

medium, the depth of penetration
1. Is independent of the attenuation constant.

2. Has logarithmic relationship with the attenuation constant

3. Is directly proportional to the attenuation constant

4. Is inversely proportional to the attenuation constant

156. For an FM wave, the maximum frequency deviation is 75kHz,

if the frequency sensitivity is 3 kHz/V and the modulating signal has
an amplitude of 9V then the percentage modulation is
1. 36%

2. 33%

3. 100%

4. 277%

157. For free space,

1. J=0

2. σ=0
3. σ = infinity
4. μr =0

158. For lossless line

1. α=0, β≠0
2. α≠0, β≠0

3. α=0, β=0

4. α≠0, β=0

159. For Maximum gain amplifier design, what kind of matching

been proposed?

1. Conjugate matching
2. Complex matching

3. Resistive matching

4. lattice matching.

160. For real time voice transmission the suitable multiple access
type is
1.Dynamic access

2. Fixed assignment based access

3. Random access

4. Reservation access

161. For self-sustain oscillations, the conditions to be satisfied for

op-amp oscillators are
1. Avβ > 1, Phase Shift 0°

2. Avβ < 1, Phase Shift 90°

3. Avβ = 1, Phase Shift 0°

4. Avβ = 1 only
 162. For small signal ac operation, a practical forward biased
diode can be modeled as
1. Resistance and capacitance in series

2. Ideal diode and resistance in parallel

3. Resistance
4. Resistance and ideal diode in series

163. For the resonance circuit ω0 = 105, Q = 50, R = 400 Ω the

value of C is

1. 125 pF

2. 1000 pF.

3.

250 pF.

4.

500 pF.

164. For Vd > ±4VT, the function of differential amplifier will be

1. Switch

2. Limiter
3. Automatic gain control

4. Linear Amplifier
 165. Forward and inverse Fourier transforms exist for samples
having values
1. finite
2. discrete

3. infinite

4. integers

166. Fourier transform of unit impulse at origin is

1. 1
2. 0

3. infinity

4. undefined

167. Free space loss

1. does not consists of loss to due to diffraction, reflection and niose etc.,

2. does consists of loss to due to diffraction, reflection and niose etc.,

3. reflection loss due to tall buildings

4. reflection due to ionosphere

168. FSK is used mostly in

1. Telephony

2. Radar communication

3. Radio transmission

4. Telegraphy

169. Generally, the gain of a transistor amplifier falls at high

frequencies due to the
1. Skin effect

2. Coupling capacitor at the output

3. Coupling capacitor at the input

4. Internal capacitance of the device

170. Given A = -6ax + 3 ay + 2 az, the projection of A along ay is

1. 3
2. 7

3. -12

4. -3

171. Given field A = 3x2yz ax + x3z ay + (x3y – 2z) az , it can be said

that A is

1. Divergenceless
2. Harmonic

3. Conservative

4. Solenoidal

172. Greater, values of continuous variables, spectrum of Fourier

transform will be
1. contracted
2. discrete

3. continuous

4. expanded

173. GSM uses what digital modulation technique?

1. GMSK
2.
GFSK

3.

QAM

4.

BPSK

174. Higher value of Q is achievable in

1. big cluster size
2. medium cluster size

3. micro cluster size

4. small cluster size

175. How many basic binary subtraction operations are possible?

1. 1
2. 2

3. 3

4. 4

176. How many carrier frequencies are used in BFSK

1.

2.
2

3. 4 4. 3

177. How many exclusive-NOR gates would be required for an 8-

bit comparator circuit?
1. 4
2. 6

3. 8
4. 10

178. How many flip-flops are required to make a MOD-32 binary

counter
1. 6

2. 5
3. 3

4. 4

179. How many flip-flops are required to produce a divide-by-128

device?
1. 7
2. 1

3. 4

4. 6

180. How many memory chips of (128 x 8) are needed to provide

a memory capacity of 4096 x 16?
1. 24

2. 32

3. 46

4. 64

181. How many op-amps are required to implement this

equation?
1. 4

2. 1

3. 2
4. 3

182. How much current will flow in a 100 Hz series RLC circuit if VS
= 20 V, RT = 66 ohms and XT = 47 ohms?

1.

1.05 A

2.

303 mA

3. 107 mA

4. 247 mA

183. Identify the statement that is not true for ferromagnetic

materials
1. They loss their nonlinearity property above the Curie Temperature

2. They have fixed value of μr

3. They have large χm

4. Energy loss is proportional to the area of the hysteresis loop

184. If a signal x(t) is differentiated ‘m’ times to produce an

impulse then its Fourier coefficients will be proportional to,
1. 1/nm
2. 1/nm-1

3. nm-1
4. nm

185. If a sinusoidal modulating signal is uniformly quantized with a

(SNR)q of 20dB, determine the number of bits required per sample
1. 4

2. 2

3. 3

4. 5

186. If a system requires 4 kHz of bandwidth to continuously send

8000 binary digits/sec, the bandwidth efficiency will be _______
1. 2 bits/s/Hz
2. 1 bits/s/Hz

3. 32 bits/s/Hz

4. 0.5 bits/s/Hz

187. If a transistor is operating with both of its junctions forward

biased, but with the collector base forward bias greater than the
emitter base forward bias, then it is operating in the
1. Reverse saturation mode

2. Reverse active mode

3. Forward active mode

4. Forward saturation mode

188. If a transistor operates at the middle of the dc load line, a

decrease in the current gain will move the Q point
1. down
2. nowhere

3. off the load line

4. up
 189. If a two-port is reciprocal, which of the following is not true?

1.
h21 = h12

2. AD = BC + 1 3. y21 = y12

4.

z21 = z12

190. If all the poles of the system function H(Z) have magnitude
smaller than 1, then the system will be,
1. BIBO stable

2. stable
3. marginally stable

4. unstable

191. If an 8-bit ring counter has an initial state 10111110, what is

the state after the fourth clock pulse
1. 11110000

2. 00000000

3. 00010111

4.00001011
 192. If bit energy to noise density ratio is 10dB and feedback shift
length is 10, then the jamming margin is approximately

1. 20dB

2. 30dB

3. 32dB

4. 26dB

193. If BPSK modulation is used for transmission of data, the

required minimum bandwidth is 9600Hz.To reduce the
transmission bandwidth to 2400Hz, the modulation scheme
adapted should be
1. 8-ary PSK

2. Minimum Shift Keying

3. Quadrature Phase Shift Keying

4. 16-ary PSK

194. If each character in a 45 character text message is encoded

using an 8-bit ASCII code, how many bits would be required to
encode the entire message?
1. 420

2. 360
3. 440

4. 480

195. If G(f) represents the Fourier transform of a signal g(t) which

is real and odd symmetric in time, then
1. G(f) is real

2. G(f) is complex

3. G(f) is imaginary
4. G(f) is real and non-negative
 196. If n is the +ve frequency power density , the power density of
white noise d(ω) is equal to
1. 2n

2. n/2

3. 1/n

4. n

197. If the ac supply is 50 Hz, what will be the ripple frequency out
of the full-wave rectifier?
1. 50 Hz

2. 100 Hz
3. 60 Hz

4. 120 Hz

198. if the differential mode voltage gain and the common mode
voltage gain of the differential amplifier are 48dB and 2 dB
respectively, then its common mode rejection ratio is ___
1. 25dB

2. 23dB

3. 46dB
4. 50dB

199. If the initial current is nonzero, then the impedance must be

placed in series with a voltage source
1. Li(0+)

2. −Li(0+)

3. −Li(0−)

4. Li(0−)
 200. If the initial voltage is nonzero, then the impedance must be
placed in series with a voltage source ______________
1. v(0−)/s

2. -v(0−)/s

3. -v(0+)/s

4. v(0+)/s

201. If the intermediate frequency is very high (indicate the false

statement)
1. the local oscillator need to be extremely stable

2. image frequency rejection is very good

3. the selectivity will be poor

4. tracking will be improved

202. If the modulation index of an AM wave is changed from 0 to

1, the transmitted power
1. Remains unaffected

2. Increase by 100%

3. Increase by 75%

4. Increase by 50%

203. If the number of bits per sample in PCM system is increased

from n to n + 1, then the improvement in signal to quantization
noise ratio will be

1.

3 db

2.
10 db

3.
6 db

4. 8db

204. If the percentage reactance of an element is 20 % and the full

load current is 50 A, the short circuit current will be

1.

200 A.

2.

300 A.

3.
250 A.
4. 350 A

205. If the radiation from the antenna is expressed in terms of the

field strength(either E or H ) then the radiation pattern is called as

1. Voltage pattern

2. field pattern
3. current pattern

4. reflection pattern
 206. If the sheet of a bakelite is inserted between the plates of an
air capacitor, the capacitance will
1. become zero

2. increase
3. decrease

4. remains unchanged

207. If the spacing between received pulses deviated from its

assigned value a -------------- is introduced into the regenerated
pulse position.
1. Bit error

2. interference

3.

Data rate

4.
Jitter

208. If wet soil has σ = 10-2 mho/m, εr = 15, μr = 1, f = 60 Hz, it is

a
1. Good conductor
2. semi- conductor

3. good dielectric

4. magnetic material
 209. If ƒ(x,y) is imaginary, then its Fourier transform is
1. antihermition
2. hermition

3. symmetry

4. Conjugate symmetry

210. Impulse has property called

1. rotating property

2. additive property

3. shifting property
4. additive inverse

211. In a ______ handoff, a mobile station can communicate with

two base stations at the same time
1. Soft
2.hard - medium 3. Hard

4. Medium

212. In a binary PCM system, the output signal-to-quantizing-

noise ratio is to be held to a minimum of 40dB. Determine the
number of required bits for the quantizer to satisfy the above
requirement.
1. 7

2. 5

3. 4

4. 8

213. In a C-E configuration, an emitter resistor is used for

1. collector bias

2. stabilization
3. higher gain

4. ac signal bypass

214. In a CD player, the sampling rate is 44.1 kHz and the samples
are quantized using a 16-bit/sample quantizer. The resulting
number of bits for a piece of music with a duration of 50 minutes is
1. 1.39 x 109

2. 4.23 x 109
3. 8.46 x 109

4. 12.23 x 109

215. In a cellular system, ________ is used to measure the

spectrum efficiency.
1.

Diversity

2. Radio capacity
3. Radio efficiency 4.

Frequency reuse

216. In a certain CS amplifier, VDS = 3.2 Vrms and VGS =

280mVrms. The voltage gain is
1. 8.75

2. 1

3. 3.2

4. 11.4

217. In a comparator with output bounding, what type of diode is

used in the feedback loop?
1. zener
2. junction

3. shottky
4. varactor

218. In a dielectric-conductor boundary (interface), the tangential

component of electric field is

1. infinity 2. E t

3. zero
4. 2Et

219. In a GSM system, eight channels co-exist in 200 kHz

bandwidth using TDMA. A GSM based cellular operator is allocated
5 MHz bandwidth. Assuming a frequency reuse factor of 1/5 (five-
cell repeat pattern), the maximum of simultaneous channels that
can exist in one cell is
1. 40
2. 100

3. 50

4. 200

220. In a modulo-16 ripple counter using JK flipflip, if each flipflop

propagation delay is 50nsec, the maximum clock frequency that
can be used is equal to
1. 5MHz
2. 2.5MHz

3. 1.25MHz

4. 10MHz

221. In a MOSFET operating in the saturation region, the channel

length modulationeffect causes
1. a decrease in the Transconductance
2. an increase in the gate-source capacitance

3. a decrease in the unity-gain cutoff frequency

4. a decrease in the output resistance

222. In a P+N junction diode under reverse bias, the magnitude of

electric field is maximum at
1. The edge of the depletion region on N side

2. The centre of the depletion region on the N side

3. The P+N junction

4. The edge of the depletion region on P side

223. In a PCM system, amplitude levels transmitted in 6

bits.Sampling done at 10kHz.Bandwidth should be
1. 40kHz

2. 45kHz

3. 30kHz

4. 35kHz

224. In a power supply diagram, which block indicates a pulsating

dc output?
1. regulator

2. filter

3. rectifier
4. transformer

225. In a series RLC circuit the current can be found using:

1.

I = Irms / √2
2.

I = V(across source) / Z

3.

I = V(across resistance)/R

4.

I = Irms * √2

226. In a time multiplexed switching system, one speech sample

appears every
1. 20ms

2. 125ms
3. 125microsec

4. 100ms

227. In a transistor, collector current is controlled by

1.base voltage

2. base current
3. collector voltage

4. collector resistance

228. In amplitude modulated system, the total power is 600W and

the power in carrier is 400W, then the modulation index is
1. 1 2. 0.75

3. c) 0.90

4.

0.5
 229. In an SSB transmitter one is most likely to find
1. Class - C audio amplifier

2. Class - B RF amplifier
3. Tuned modulator

4. Class- AB power amplifier

230. In broadcast super heterodyne receiver, the

1. local oscillator operates below the signal frequency

2. mixer input must be tuned to the signal frequency

3. local oscillator frequency is normally double the IF

4. RF amplifier normally works at 455KHz above the carrier frequency

231. In CDMA, Reduction of co channel interference due to

processing gain allows frequency reuse factor of ________.
1. One
2. Zero

3. Infinity

4. Ten

232. In CDMA, the system uses ______for the Forward and

Reverse links
1. TDD

2. TDMA

3. FDD

4. FDD and TDD

233. In circular waveguide the dominat mode is

1. TE20

2. TE10

3. TE21

4. TE11

234. In commercial TV transmission in India, picture and speech

signal are modulated respectively as
1. VSB and FM
2. VSB and VSB

3. VSB and SSB

4. FM and VSB

235. In FDM system used for telephone, which modulation

scheme is adopted?

1. FM
2.

AM

3.

DSB-SC

4.

SSB

236. In FHSS, spectrum of transmitted signal is spread

1. By a multiplicative factor N

2. Sequentially

3. Instantaneously

4. Additively
 237. In MOSFET devices, the N-channel type is better than the P-
channel type in the following respects
1. It has better drive capability

2. It is TTL compatible

3. It has better noise immunity

4. It is faster

238. In phase modulation, frequency deviation is

1. Inversely proportional to the modulated signal frequency

2. Inversely proportional to the square root of the modulation frequency

3. Independent of the modulated signal

4. Directly proportional to the modulated signal frequency

239. In Repetition Code, how many information bit/s is/are

present in addition to n-1 parity bits?
1. One

2. Two

3.

Four

4. Eight

240. In sky wave propagation, the shortest distance covered by

the single frequency untouched to the ground is called
as_____________.
1. Line of sight

2. skip distance
3. transmitted distance
4. 2 – ray distance

241. In the envelope of an AM wave, given Vmax = 30 volts and

Vmin = 10 volts. Determine the modulation index and message
signal amplitude?
1. 0.25, 10V

2. 0.25, 20V

3. 0.5, 10V

4. 0.5, 20V

242. In the left half of the Smith chart, the resistance and
reactance values are
1. less than 1
2. 2

3. more than 1

4. Zero

243. In the spectrum of a frequency modulated wave

1. the carrier frequency cannot disappear

2. the total number of side-bands not depend on the modulation index

3. the carrier frequency disappears when the modulation index is large

4. the amplitude of any sideband depends on the modulation index

244. In VCO IC 566, the value of charging & discharging is

dependent on the voltage applied at ______.
1. Triangular input

2. Modulating input
3. Square wave output

4. Triangular wave output

 245. In which of the following are operational amplifiers (op-
amps) used?
1. Filters

2. Instrumentation circuits

3. Oscillators

4. All of the above

246. In which of the following multiple access schemes, the

frequency reuse concept is utilized?
1. SDMA

2. FDMA
3.TDMA

4. CDMA

247. Indicate the false statement

1. Industrial noise is usually of the impulse type

2. Thermal noise is independent of the frequency at which it is measured

3. Impulse noised voltage is independent of the bandwidth

4. HF mixers are generally noisier than HF amplifiers

248. Indicate the false statement regarding the Armstrong

modulation system
1. Frequency multiplications must be used

2. AFC is not needed, as the crystal oscillator is used

3. the system is basically phase and not frequency modulation

4. Equalization is unnecessary

249. Indicate the false statement. The super heterodyne receiver

replaced the TRF receiver because the latter suffered from
1. inadequate selectivity at high frequencies

2. insufficient gain and sensitivity

3. gain variation over the frequency coverage range

4. instability

250. Indicate the noise whose source is in a category different

from that of the other three
1. Galactic Noise

2. Cosmic Noise

3. Atmospheric Noise
4. Solar Noise

251. Inductors may be represented in the frequency domain by an

impedance as _______________
1. 1/sL

2. -sL

3. sL
4. -1/sL

252. Input impedance of transmission line does not depends on

1. Characteristics impedance

2. Frequency

3. Length of the line

4. Source impedance

253. Internal antenna for mobile handset is ...........................

1. Planar Inverted-F antenna
2. Dish antenna

3. Horn antenna

4. Spiral antenna

254. It is the functional entity from which the operator monitors

and controls the mobile communication system.

1.

Gateway Mobile Switching Center

2.
Operation and Maintenance System

3.

Mobile Switching Center

4. Operation and Support System

255. Johnson noise is

1.
White for all practical frequencies

2. Depends on temperature.

3.

Never white
4.

Always white

256. Laplacian of a Scalar function F is

1. gradient of F

2. divergence of gradient of F
3. divergence of F

4. gradient of gradient of F

257. Laplacian of a scalar function V is

1. Gradient of V

2. Divergence of V

3. Gradient of the gradient of V

4. Divergence of the gradient of V

258. Laser light is very bright because it is

1. Monochromatic

2. Coherent
3. White

4. Pure

259. Most common example of temporal aliasing is

1. ringing effect

2. image sharpening

3. wagon wheel effect

4. blurring
 260. Most of the electrons in the base of an NPN transistor flow
1. out of the base lead

2. into the base supply

3. into the emitter

4. into the collector

261. Most significant bit of arithmetic addition is called

1.

overflow

2. Carry
3. Output

4. Zero Bit

262. No of ripple counter IC is

1. 7865

2. 7654

3. 7492

4. 7493

263. Number of channels for GSM

1. 666

2. 248

3. 124
4. 333
 264. Of the following,the incorrect relation is
1. D=εE

2. B=μH

3. J=σE

4. B=μD

265. On which factor/s do/does the channel capacity depend/s in

the communication system?
1. Decibel

2. Signal to Noise Ratio

3. Bandwidth and SNR

4. Bandwidth

266. On which of the following factors does the sensitivity of a

closed loop system to gain changes and load disturbances depend
?
1. Frequency

2. Loop gain

3. All of the above

4. Forward gain

267. On-off keying is the modulation scheme used for the majority
of optical-fiber communication systems. This scheme is an example
of
1. Binary phase shift keying

2. Binary frequency shift keying

3. Continuous-phase frequency shift keying

4. Binary amplitude shift keying

268. One of the advantages of base modulation over collector

modulation of a transistor class C amplifier
1. the lower the modulating power required
2. high power output per transistor

3. better efficiency

4. better linearity

269. One of the following is not a source of Magnetostatics field:

1. A permanent magnet

2. An accelerated charge
3. A dc current in a wire

4. The electric field linearly changing with time

270. One of the following types of noise becomes a great

importance at high frequencies
1. Impulse Noise

2. Shot Noise

3. Transit Time Noise

4. Random Noise

271. One of the main functions of the RF amplifier in a super

heterodyne receiver is to
1. provide improved tracking

2. permit better adjacent-channel rejection

3. increase the tuning range of the receiver

4. improve the rejection of the image frequency

272. One of the major drawbacks to the use of asynchronous

counters is that:

1. Asynchronous counters do not have propagation delays, which limits their use in
high-frequency applications.
2. low-frequency applications are limited because of internal propagation delays

3. Asynchronous counters do not have major drawbacks and are suitable for use in high- and low-
frequency counting applications

4. high-frequency applications are limited because of internal propagation delays

273. PAM signal can be demodulated by using a

1. Low Pass Filter (LPF) alone
2. Schmitt trigger followed by LPF

3. Clipper circuit followed by a LPF

4. Differentiator followed by a LPF

274. Plane y = 0 carries a uniform current of 30az mA/m. At

(1,10,-2), the magnetic field intensity is ______
1. 15ax mA/m

2. 15ay mA/m

3. -15ay mA/m
4. -15ax mA/m

275. Plane z = 10m carries charge 20nC/m2. The electric Field

intensity at the origin is

1. -360π az
2. -10az V/m

3. -18π az V/m

4. -72π az V/m

276. Pre-emphasis in FM systems involves

1. Compression of the modulating signal

2. Expansion of the modulating signal

3. Amplification of lower frequency components of the modulating signal

4. Amplification of higher frequency components of the modulating signal

277. Process of converting plaintext into ciphertext

1. Encryption
2. Decryption

3. compression

4. Authentication

278. QPSK requires ----------------transmission bandwidth of the

BPSK
1. twice

2. 1/3

3. ½
4. ¼
 279. Quantization bit rate for a an analog i/p signal with a
bandwidth of 3.4 kHz in a delta modulator with a signal to
quantization noise ratio of 25dB, will be
1. 58 kb/s

2. 68 kb/s

3. 78 kb/s

4. 48 kb/s

280. Radio channel used for transmission of information from the

mobile to the base station is called as ____________________
1. Reverse Control Channel

2. Reverse Voice Channel

3. Forward Voice channel

4. Forward Control Channel

281. RC low pass filter is a

1.Linear and time variant system

2. Linear and time invariant system

3. Time variant system

4. Linear system

282. Real audio/video signal is a/an

1. Power Signal

2. Periodic Signal

3. Energy Signal
4. Deterministic Signal

283. Reason for call drop is

1. External Noise
2. Handoff
3. Channel Assignment

4. Co-channel Interference

284. Rectangular Waveguide behaves as

1. Waveguide cant behave as filter

2.

Low pass filter

3.

All pass filter

4.
High pass filter

285. Rectifier output polarity depends upon:

1.

cycles of input

2. diode installation
3.

capacitor polarity

4. half or full wave

286. Reducing the cellsize to increase capacity is called as -----------

----.
1. Top down approach

2. Microcell Approach
3. Intelligent cell approach

4. Bottom up approach

287. Refer to this figure. Determine the frequency of oscillation,

1. 232 Hz

2. 262 Hz

3. 2.62 kHz

4. 131 Hz

288. Regenerative feedback:

1.Bandwidth decreases
2. Implies feedback with positive sign
3. Is used to increase the loop gain of the feedback system

4. Has the transfer function with a negative sign in the denominator

289. Resistors may be represented in the frequency domain by an

impedance having the ____________
1. same magnitude
2. opposite in magnitude

3. complex in magnitue

4. negative complex in magnitue

290. Sampled frequency less than nyquist rate is called

1. critical sampling

2. nyquist sampling

3. under sampling
4. over sampling

291. Sectorization Reduces Interference and adds a Gain to the

system which is called _______________
1. FER

2. Sectorization removal

3. Cell breathing

4. Sectorization Gain

292. Shannon’s law relates

1. Frequency to antenna gain

2. Antenna gain to transmission losses

3. Information carrying capacity to S/N ratio

4. Antenna gain to bandwidth

 293. Source encoding of digital data is performed
1. suitable signaling format for transmission over channel

2. for reliable transmission through the channel

3. for the efficient use of channel

4. for more robust transmission

294. Speech is coded at low bit rates

1. to remove quantization noise

2. to provide high quality of reproduction

3. to secure transmission over channels having low capacity

4. to increase SNR

295. Spiral antenna is a

1.non-radiating

2. narraow band antenna

3. broadband antenna
4. dual band antenna

296. Stack is ___________Memory

1. Volatile RAM

2. Non Volatile ROM

3. Volatile ROM
4. Non Volatile RAM

297. Step size can be made smaller for smaller signals and larger
for larger signals
1. ADM

2. DM
3.

DPCM
4. PCM

298. Stokes theorem relates

1. surface integral and line integral

2. surface integral and volume integral

3. volume integral and contour integral

4. line integral and volume integral

299. Sum of many infinitely many periodic impulses is called

1. aperiodic impulse

2. periodic impulse

3. impulse train
4. summation

300. Suppose only one multiplexer and one inverter are allowed
to be used to implement any Boolean function of n variables. What
is the minimum size of the multiplexer needed?

1.

2n line to one line

2.

2n+1 line one line

3. 2n-1 line to one line
4. 2n-2 line to one line

301. Suppose we sample a signal at frequency Fs. If we collect

1500 samples in 5 seconds, what is Fs in Hz?
1. 350

2. 400

3. 300
4. 4500

302. Switching technology used in 4G

1.circuit with packet switch

2. Digital with packet voice

3. Circuit Switched

4. Packet Switched

303. Symbols 1 and 0 are represented by pulse of equal positive

and negative amplitudes is called as
1. NRZ- Polar
2.

RZ- Polar

3. NRZ- Unipolar
4. RZ- Unipolar

304. Synchronization is an important aspect in

1. Time Division Multiple Access
2. Code Division Multiple Access

3. Space Division Multiple Access

4. Frequency Division Multiple Access

305. Synchronous counters eliminate the delay problems

encountered with asynchronous (ripple) counters because the:

1. input clock pulses are applied simultaneously to each stage

2. input clock pulses are not used to activate any of the counter stages

d) input clock pulses are applied simultaneously to each stage

3. input clock pulses are applied only to the last stage .

4. input clock pulses are applied only to the first and last stages.

306. System of embedding links in a text to link to other text

1. Java

2. HTML

3. Embedded linking
4. HTTP

307. The 8-bit address bus allows access to an address range of:
1. 0 to FH

2. 00 to FFH
3. 000 to FFFH

4. 0000 to FFFFH
 308. The ________ of radio receiver amplify weak signal and
produce a desirable intelligence at the output speaker.
1. fidelity

2.

selectivity

3. sensitivity 4.
reliability

309. The _________ is a database that contains information about

the identity of mobile equipment that prevents calls from stolen,
unauthorized, or defective mobile stations.
1. XME

2. HLR

3. EIR
4. AUC

310. The acceptable VSWR level of the antenna is upto

......................
1. 10

2. 0.1

3. 1

4. 2

311. The area at the junction of p-type and n-type materials that
has lost its majority carriers is called the _______
1. barrier potential

2. p region
3. depletion region
4. n region

312. The bandwidth of an amplifier is _________ by a negative

feedback
1. unaffected

2. attenuated

3. maintained

4. augmented

313. The bandwidth of an amplifier is determined by

1.3dB cut-off frequencies
2. The input capacitances

3. The critical frequencies

4. The midrange gain

314. The binary numbers A = 1100 and B = 1001 are applied to the
inputs of a comparator. What are the output levels?
1. A > B = 1, A < B = 0, A < B = 1

2. A > B = 0, A < B = 1, A = B = 0

3. A > B = 1, A < B = 0, A = B = 0
4. A > B = 0, A < B = 1, A = B = 1

315. The bit sequence 0010 is serially entered (right-most bit first)
into a 4-bit parallel out shift register that is initially clear. What are
the Q outputs after two clock pulses?
1. 0000

2. 0010

3. 1000
4. 1111
 316. The bit sequence 10011100 is serially entered (right-most bit
first) into an 8-bit parallel out shift register that is initially clear.
What are the Q outputs after four clock pulses?
1. 11110000

2. 00001100

3. 11000000
4. 10011100

317. The capacity of an analog communication channel with 4kHz

bandwidth and 15dB SNR is approximately
1. 16,000 bps

2. 8,000 bps

3. 20,000 bps
4. 10,000 bps

318. The capacity of the wire-line system can be increased

1. By increasing the number of wires

2. By random access

3. By TDMA

4.By increasing the number of wires or random access or TDMA

319. The carry propagation can be expressed as

1. Cp = AB

2. Cp = A + B
3. Cp = A^B

4. Cp = A+B’
 320. The cell having the same number in the adjacent cluster
using the same set of RF channels are termed as
1. Co channel cell
2. Macro cell

3. Selective Cell

4. Adjacent cell

321. The cellular technology that brings perfect real world

wireless is called WWWW : “World Wide Wireless Web” is

1. 3G

2. 4G
3. 1G

4. 2G

322. The center frequency of a band-pass filter is always equal to

the

1.

3 dB frequency

2. geometric average of the critical frequencies

3.

bandwidth divided by Q

4.

bandwidth
 323. The characteristic impedances Z0 of a transmission line is
given by, (where R, L, G, C are the unit length parameters)
1. (R + jωL)(G + jωC)

2. (R+ jωL)2 / (G +jω C)

3. [(R+ jωL)/ (G +jω C)]1/2

4. (R + jωL)/(G + jωC)

324. The Circuit which converts undirectional flow to D.C. is called

_______
1. filter circuit
2. Eliminator

3. Rectifier circuit

4. Converter circuit

325. The circuits in homes are connected in parallel rather than

series because it is
1.

Economical

2. easy to do

3. possible to get same current 4. possible to get same voltage

326. The closed loop gain of the wein bridge oscillator must be
_______
1. Acl<3

2. 0

3. ACl=1
4. Acl=3

327. The closed loop power control also uses an outer loop power
control. This method measures the __________________both by
the mobile and the base station and then adjusts the power
according to whether it is acceptable.
1. Frame Error Rate (FER)

2. Bit Error Rate (BER)

3. Signal to Noise Ratio

4. Power ratio

328. The combination of the mobile cellular phone and the cell-
site radio equipment is known as

1. base station controller 2. air interface

3.

forward link

4.

base transceiver station

329. The comparator using op-amp with input sine waveform

gives
1. triangular waveform

2. square form

3. cos waveform
4. sine waveform

330. The constellation diagram of QPSK has

1. 8 2. 1

3.

4. 4

331. The core concept used in Cellular technology is

1. Frequency Reuse
2. FDM

3. Code reuse

4. TDM

332. The current gain of a bipolar transistor drops at high

frequencies because of
1. Parasitic inductance effects

2. The Early Effect

3. High current effects in the base

4. Transistor capacitances

333. The defining equations for analyzing a two-port network in

terms of its admittance (y) parameters are:
1. I1 = y11V1 + y12V2 and I2 = y21V1 + y22V2
2. V1 = z11I1 + z12I2 and V2 = z21I1 + z22I2

3. V1 = t11V2 − t12I2 and I1 = t21V2 − t22I2

4. V1 = h11I1 + h12V2 and I2 = h21I1 + h22V2

 334. The defining equations for analyzing a two-port network in
terms of its impedance (z) parameters are:
1. I1 = y11V1 + y12V2 and I2 = y21V1 + y22V2

2. V1 = z11I1 + z12I2 and V2 = z21I1 + z22I2

3. V1 = h11I1 + h12V2 and I2 = h21I1 + h22V2

4. V1 = t11V2 − t12I2 and I1 = t21V2 − t22I2

335. The defining equations for analyzing a two-port network in

terms of its transmission (t) parameters (also called the ABCD
parameters) are:
1.

V1 = h11I1 + h12V2 and I2 = h21I1 + h22V2

2. V1 = z11I1 + z12I2 and V2 = z21I1 + z22I2

3. I1 = y11V1 + y12V2 and I2 = y21V1 + y22V2

4. V1 = t11V2 − t12I2 and I1 = t21V2 − t22I2

336. The depth of penetration of a wave in a lossy dielectric

increase with increasing

1. permeability

2. conductivity

3. wavelength
4. permittivity

337. The difference between the phase and frequency modulation

1. is too great to make the two system compatible

2. is purely theoretical because they are the same in practice

3. lies in the different definitions of the modulation index
4. lies in the poorer audio response of the phase modulation

338. The diffusion potential across a PN junction

1. Increases with decreasing band gap

2. Increases with increase in doping concentrations

3. Decreases with increasing doping concentration

4. Does not depend on doping concentration

339. The direction of electric field due to positive charge is

1. perpendicular to the charge

2.parallel to the charge

3. towards the charge

4. away from the charge

340. The effective channel length of a MOSFET in saturation

decreases with increase in
1. Drain voltage
2. Body voltage

3. Source voltage

4. Gate voltage

341. The electric and magnetic fields (components) radiated from

an antenna form the _______________ field.

1. radiation

2. magnetic

3. electro-magnetic
4. induction
 342. The electric field at a point situated at a distance d from
straight charged conductor is
1. inversely proportional to d
2. proportional to d

3. inversely proportional to H 4. proportional to H

343. The electric flux density on a spherical surface r=b is the

same for a point charge Q located at the origin and for the charge
Q uniformly distributed on surface r=a (a
1. It will be higher

2. Not necessarily

3. No

4. yes

344. The electric susceptibility of a dielectric is 4, its permittivity is

1. 2.26 x 10-9 F/m

2. 4.42 x 10-7 F/m

3. 5 F/m
4. 1.26 x 10-3 F/m

345. The EM field and current are concentrated close to the

surface of the conductor. The phenomenon is called

1. Ohm’s effect

2. Skin effect
3. Faraday’s effect

4. EM concentration effect
 346. The ends of a load line drawn on a family of curves
determine
1. the amplification factor

2. saturation and cutoff

3. the power curve

4. the operating point

347. The envelop detector is an

1. Asynchronous detector
2. Synchronous detector

3. Coherent detector

4. Product demodulator

348. The Ex-NOR is sometimes called the

1. Parity gate or the equality gate
2. inverted OR

3. equality gate

4. parity gate

349. The extra time needed to bring the data into memory in case
of a miss is called as
1. Miss penalty
2. jitter

3. Propogation Time

4. Delay
 350. The figure shown below is a Mod-K counter, K = ……………

1. 3
2. 1

3. 2

4. 4

351. The final value of x(t ) = [2+ e - 3t ]u(t ) is

1. e-3t

2. 3

3. 2
4. 0

352. The force between two charges is 120 N. If the distance

between the charges is doubled, the force will be
1. 15 N

2. 30 N
3. 40 N

4. 60 N
 353. The Fourier Transform of a conjugate symmetric function is
always
1. real
2. conjugate symmetry

3. Imaginary

4. conjugate anti-symmetric

354. The Fourier Transform of a rectangular pulse is

1. Triangular pulse

2. Another rectangular pulse

3. Sinc function
4. Impulse

355. The Fourier transform of the exponential signal ejω0t is

1. an impulse
2. a constant

3. a rectangular gate

4. a series of impulses

356. The frequency of a continuous time signal x(t) changes on

transformation from x(t) to x(αt), α>0 by a factor
1.

α1/2

2.

1/ α

3.
α

4.
α2

357. The frequency range of 1GHz to 30 GHz are referred as

1. Mini waves

2. Light waves

3. Sound waves

4. Microwaves

358. The gain of op-amp decreases to high frequencies because of

1. capacitor within op-amp
2. feedback network with active device

3.capacitor in the feedback

4.resistance in the feedback

359. The image frequency of a super heterodyne receiver

1. is not rejected by the IF tuned circuits

2. is due to insufficient adjacent channel rejection

3. is created within the receiver itself

4. is independent of the frequency to which the receiver is tuned

360. The impedance of a 10-F capacitor is:

1. 1/10s
2. 10/s

3. s/10

4. 10s
 361. The impulse response of a LTI system is a unit step function,
then the corresponding transfer function is
1. 1

2. 1/s2

3. 1/s
4. s

362. The input impedance of a λ/2 transformer is

1.input imepedance

2. terminal admittance

3. characteristics impedance

4. terminal impedance

363. The intrinsic impedance of free space is

1. 75 ohm

2. 73 ohm

3. 120 ohm

4. 377ohm

364. The intrinsic impedance of the medium whose σ = 0, εr = 9,

μr = 1 is

1. 120 πΩ

2. 9Ω

3. 60 πΩ
4. 40 πΩ

365. The inverting amplifier is a

1. Voltage shunt feedback amplifier
2. Current shunt feedback amplifier

3. Current series feedback amplifier

4. Voltage series feedback amplifier

366. The largest frequency that will be returned to earth when

transmitted vertically under given ionosphere conditions is called
the_________.
1. hop frequency

2. Critical frequecny

3. LUF

4. MUF

367. The lines of force due to charged particles are

1. sometimes curved

2. always straight

3.not straight

4. always curved

368. The local oscillator of a broadcast receiver is tuned to a

frequency higher that the incoming frequency
1. to help the image frequency rejection

2. to permit easier tracking

3. to allow adequate frequency coverage without switching

4. because otherwise an intermediate frequency could not be produced
 369. The magnetic field intensity (in A/m ) at the centre of a
circular coil of diameter 1 metre and carrying current of 2 A is
1. 3

2. 4

3. 2
4. 8

370. The maximum efficiency of full wave rectification is

1. 85.6%

2. 81.2%
3. 100%

4. 40.6%

371. The Maximum power efficiency of an AM modulator is

1. 25%

2. 75%

3. 50%
4. 100%

372. The minimum number of comparators required to build a 8-

bit flash type ADC is
1. 8

2. 255
3. 256

4. 63

373. The mobile-to-base station frequency assignment for GSM

system is
1.
935-960 MHz

2. 825-845 MHz 3. 870-890 MHz

4.

890-915 MHz

374. The modulating frequency in frequency modulation is

increased from 10 kHz to 20 kHz. The bandwidth is
1.
Increased by 20 kHz

2.

doubled

3.

Halved

4. Increase tremendously

375. The modulation index of an AM is changed from 0 to 1. The

transmitted power is
1. Increase by 50%
2. Unchanged

3. Halved

4. Doubled
 376. The most bandwidth efficient scheme is
1. OFDM
2. TDM

3. CDM

4. FDM

377. The normal operating region for a zener diode is the

1. forward-bias region

2. reverse-breakdown region
3. zero-crossing region

4. reverse-bias region

378. The number of bits in a binary PCM system is increased from

n to n+1. As a result, the signal to quantization noise ratio will
improve by a factor.
1. 2^(n+1)/n

2. Which is independent of n
3. (n+1)/n

4. 2^2(n+1)/n

379. The Nyquist sampling rate for a signal band limited 5 kHz is

1.

2.5 kHz

2. 20 kHz 3. 5 kHz

4.
10 kHz
 380. The output frequency for a frequency division circuit that
contains 12 flip-flops with an input clock frequency of 20.48 MHz is
1. 5 kHz
2. 15 kHz

3. 30.24 kHz

4. 10.24 kHz

381. The output frequency of a full-wave rectifier is ________ the

input frequency.
1. one-half

2. equal to

3. twice
4. one-quarter

382. The output is zero for zero input, and the idle channel noise
is correspondingly Zero
1. uniform

2. Non Uniform

3. Mid-tread
4. Mid-riser

383. The output offset voltage is determined by ________.

1.both the input offset voltage and the closed-loop gain

2. input offset current

3. the closed-loop gain

4. the input offset voltage and input offset current

384. The output S/N ratio of a matched filter, fed at its input by a
rectangular pulse of energy A and duration T is given as (assume
No as noise power spectral density)
1. 2AT/No
2. AT

3. A/No

4. A/T

385. The parallel wire transmission line is an example of

1. an unbalanced line
2. a balanced line

3. lossy line

4.lossless

386. The peak amplitude of one signal level is 0; the other is the
same as the amplitude of the carrier frequency

1.

FSK

2. QPSK

3.

BPSK
4.
ASK

387. The period of the output waveform of mono-stable

multivibrator using 555 Timer with RA=7.5 kΩ and C = 0.1 µF when
triggered by a negative pulse is
1. 1.5 ms

2. 0.825 ms
3. 0.75 ms

4. 0.525 ms

388. The phenomenon of an uncharged body getting charged

merely by the nearness of a charged body is known as

1. chemical effect

2. magnetic effect

3. pholoelectric effect

4. induction

389. The potential which exists in a p-n junction to cause drift of

charge carriers is called ___
1. contact potential
2. diffusion potential

3. ionisation potential

4. threshold potential

390. The Poynting Vector has the dimensions of

1. Power/Unit area
2. Volts

3. Power

4. Volt/Unit length
 391. The Poynting Vector physically denotes the power density
leaving or entering a given volume in a time varying field.

1. Not always true

2. True
3. false

4. Not always false.

392. The primary disadvantage of the flash analog-to digital

converter (ADC) is that:
1. a large number of comparators is required to represent a reasonable sized binary number

2. a long conversion time is required

3. a large number of output lines is required to simultaneously decode the input voltage

4. it requires the input voltage to be applied to the inputs simultaneously

393. The process of channel coding, Encryption, Multiplexing and

modulation for Trans direction and reverse for reception are to be
carried out by
1. BSC

2. MSC

3. MS

4. BTS

394. The process of transferring a mobile station from one base

station to another is__________
1. Switching

2. Channel Borrowing

3. Call Setup
4. Handoff

395. The property of Fourier Transform which states that the

compression in time domain is equivalent to expansion in the
frequency domain is
1. Frequency Shifting

2. Scaling
3. Time Scaling

4. Duality

396. The purpose of using more directors in Yagi Uda antenna is to

achieve
1. less gain

2. more gain
3. less bandwidth

4. more bandwidth

397. The Q point on a load line may be used to determine

1. VB
2. Vcc

3. IC

4. VC

398. The radiation pattern we measure for a horn antenna is of E-

plane type. At what condition we will say it is an E-plane type.

1. The electric field of the radiating horn is perpendicular to ground.

2. The magnetic field of the radiating horn is in circular direction

3. The electric field of the radiating horn is parallel to ground.

4. The magnetic field of the radiating horn is parallel to ground

 399. The reflection coefficient of a transmission line with a short-
circuited load is
1.-1
2. 0.1∠0°

3. ∞

4. 0

400. The reflection coefficient over the normalized Zl

1. (Zs - 1)/ (Zs +1 )

2. (Zl + 1)/ (Zl -1 )

3. (Zl - 1)/ (Zl +1 )

4.0

401. The Relaxation time of mica (σ = 10-15 mho/m, εr =6) is

1. 10-6 s

2. 15 Hours
3. 5x 10-10 s

4. 5 Hours

402. The remote and sparsely populated areas will be covered by

1. Pico Cell

2. Macro Cell
3. Micro Cell 4. pentagon cell

403. The ripple factor of a full-wave rectifier circuit compared to

that of a half wave rectifier circuit without filter is
1. equal to that of a half wave rectifier

2.higher than half that for a half-wave rectifier circuit

3. half of that for a half ‘wave rectifier

4. less than half that for a half-wave rectifier circuit

404. The ROC of the sequence x(n) = u(-n) is,

1. |z| > 1

2. |z| < 1
3. No ROC

4. -1 < |z| < 1

405. The signal an u[n] is a power signal if

1. |a| < 1

2. |a| = 1

3. |a| = 0

4. |a| > 1

406. The signals x1(t) and x2(t) are both band limited to (-ω1,
+ω1) and (-ω2, +ω2) respectively. The Nyquist sampling rate for
the signal x1(t)x2(t) will be
1. (ω1+ ω2)/2

2. 2ω2 if ω1 < ω2

3. 2ω1 if ω1 > ω2

4. 2(ω1+ ω2)

407. The simplification of Boolean expression (a’bc’)’+(ab’c)’ is

1. a

2. bc

3. 0

4. 1

408. The surge impedance of a double-circuit power transmission

line is
1. 40 ohms
2. 800 ohms

3. 400 ohms

4. 200 ohms

409. The system characterized by the equation y(t)=ax(t)+b is

1. linear if b<0

2. linear for any value of b

3. non-linear
4. linear if b>0

410. The system function H(z) = (z3-2z2+z)/(z2+0.25z+0.125) is,

1. Causal

2. Unstable but causal

3. Cannot be defined

4. Noncausal

411. The technique adopted to increase the system capacity and

reduce co-chl interference is
1. By installing the Omnidirectional antenna

2. Sectorisation
3. High power BTS

4.Low power BTS

412. The three terminal regulator has output following limitations:

1. short circuit protection

2. o/p voltage is fixed

3. no short circuit protection

4.o/p voltage is fixed and no short circuit protection

 413. The total electric flux through any closed surface surrounding
charges is equal to the amount of the charge enclosed”. The above
statement is associated with
1. Gauss’s law
2. Maxwell’s first law

3. Coulomb’s square law

4. Maxwell’s second law

414. The transient response of a system is mainly due to:

1. Friction

2. Inertia forces

3. Internal forces

4. Stored energy

415. The trigonometric Fourier series of an even function of time

does not contain
1. Sine term
2. Cosine term

3. Odd harmonic term

4. DC term

416. The type of access used in GSM technology is

1.SDMA

2. CDMA

3. OFDMA

4. FDMA/TDMA

417. The type of multiple access technique used in GSM is

1. FDMA
2. FDMA/TDMA
3. CDMA

4. SDMA

418. The unit impulse response of a linear time invariant system is

the unit step function u(t). For t>0, the response of the system to
an excitation e-at u(t), a>0, will be
1. 1-e-at

2. a(1-e-at)

3. ae-at

4. (1-e-at)/a

419. The unit of Electric Field is

1.
N-C
2. N

3.

C/N

4. N/C

420. The uplink frequency of P-GSM system is

1. 890-915 MHz
2.890-915 GHz

3. 1710-1785MHz

4. 1850-1910MHz
 421. The value of the resistor creating thermal noise is doubled.
The noise power generated is therefore
1. Unchanged
2. Halved

3. Quadrupled

4. Doubled

422. The velocity factor of a transmission line depends on

1. Temperature

2. Doppler effect

3. skin effect

4. Relative permittivity of dielectric

423. The velocity of an EM wave

1. Inversely proportional to β
2. Directly proportional to α

3. inversely proportional to α

4. directly proportional to β

424. The voltage across R and L in a series RL circuit is found to be

200 V and 150 V respectively. The rms value of the voltage across
the series combination is __ V
1. 450 2. 200

3.
250
4.

360
 425. The voltage through a resistor with current i(t) in the s-
domain is sRI(s).
1. False
2. Sometimes

3. Incomplete Question

4. True

426. The voltage where current may start to flow in a reverse-

biased pn junction is called the _________
1. breakdown voltage
2. barrier potential

3. forward voltage

4. biasing voltage

427. The wavelength of a wave with a propagation constant = 0.1π

+ j 0.2π

1. 10 m
2. 25 m

3. 30 m

4. 20 m

428. The wavelength of visible light extends from

1.

0.8 to 1.0 nm

2.
400 to 750 nm

3.
200 to 660 nm

4.

700 to 1200 nm

429. The work done in moving a unit positive charge from one
point to another in an electric field is known as
1. Electric discharge

2. Potential difference
3. displacement

4. charge transformation

430. The Z-transform is a,

1. finite geometric series

2. geometric series

3. infinite power series

4. finite series

431. Thermal noise has a power spectral density which is quite

uniform upto frequencies in the order of
1.
1013 Hz

2.

1010Hz

3.

1011 Hz
4.

1012 Hz

432. Thigh and Tlow for astable mode operation of IC555 are
1. thigh = 0.695 RAC

tlow = 0.695 RBC

2. tlow = 0.695 (RA + RB)C

thigh = 0.695 RBC

3. thigh = 0.695 (RA + RB)C

tlow = 0.695 (RA + 2RB)C

4. thigh = 0.695(RA + RB)C

tlow = 0.695 RBC

433. Three analog signals, having bandwidths 1200 Hz, 600 Hz,
and 600 Hz are sampled at their respective Nyquist rates, encoded
with 12 bit words, and time division multiplexed. The bit rate for
the multiplexed signal is

1.
57.6 Kbps

2.

100 Kbps

3.

27.6 Kbps

4. 10.2 Kbps

434. Time Division Multiplexing requires

1. Transmission of data at random

2. Transmission of data of only one measured

3. Constant data transmission

4. Transmission of data samples

435. To analyze the effect of intersymbol interference, eye

pattern is used. The width of the eye defines
1. distortion at sampling times

2. best sampling instant

3. margin over noise

4. sensitivity of system to timing error

436. To combat intereference,duobinary signaling is used. ‘Duo’

implies
1. Reducing error propagation by factor two

2. Doubling channel bandwidth

3. Doubling transmission capacity

4. Doubling the symbol duration

437. To operate properly, a transistor’s base-emitter junction

must be forward biased with reverse bias applied to which
junction?
1. collector-emitter

2. collector-base
3. base-emitter

4. base-collector

438. To reduce effect of aliasing, high frequencies are

1. accentuated

2. attenuated
3. removed

4. reduced
 439. To reduce the effects of noise resulting in erratic switching of
output states of a comparator, you can use
1. the upper trigger point.

2. hysteresis.
3. nonzero-level detection.

4. the lower trigger point.

440. To which one of the following generations does CDMA

belong?
1. Third generation

2. Second generation
3. Fourth generation

4. First generation

441. Total emitter current is

1. IB – IC

2. IE – IC

3. IB + IC
4. IC + IE

442. Transmission of power to a load over a transmission line

achieves optimum value when standing-wave ratio (SWR) becomes

1. 1:1
2. 2:1

3. 1:3

4. 1:2
 443. Transmitted signal energy per symbol is twice the signal
energy per bit. Identify the system
1. Pe= ½ erfc (sqrt (Eb/No)

2. Pe= ½ erfc (sqrt (Eb/2No)

3. Pe= ½ erfc (sqrt (Eb/4No)

4. Pe= erfc (sqrt (Eb/No)

444. Travel to length λg/2 over the line corresponds to rotation

over smith chart by

1. 90°

2. 180°

3. 270°

4. 360°

445. Two sequences x1(n ) and x 2 (n) are related by x 2(n) = x1(- n
). In the Z-domain, their ROCs are
1. same

2. reciprocal of each other

3. negative of each other

4. complement of each other

 446. Two thin parallel wires are carrying current along the same
direction. The force experienced by one due to other is
1. Perpendicular to the lines and attractive.
2. Parallel to the lines

3. Perpendicular to the line and repulsive

4. Zero

447. Typical human voice is centered around

1. 200-400Hz

2. 280-3000Hz
3. 400-600Hz

4. 1400-1800Hz

448. Under electrostatic conditions where does the excess charge

lies?
1. The excess charge on a conductor doesn’t reside.

2. The excess charge on a conductor resides on its outer surface

3. The excess charge on a conductor resides on its inner surface

4. The excess charge on a conductor resides in its middle surface

449. Unlike GSM, in WCDMA there is ____________dedicated

transport channel, DCH
1. two

2. one
3. three

4. four

450. Use Boolean algebra to find the most simplified SOP

expression for
F = ABD + CD +ACD + ABC + ABCD.
1. F=AC+AD
2.
F = ABD + ABC + CD
3. F = CD + AD

4. F = BC + AB

451. Voltage-divider bias provides

1. an unstable Q point
2. a stable Q point

3. a Q point that is stable and easily varies with changes in the transistor’s current gain

4. a Q point that easily varies with changes in the transistor’s current gain

452. Walsh codes are used only by the base station and in this
fashion, it is a __________CDMA on the forward link, whereas on
the return link it is ______________ CDMA,
1. synchronous, asynchronous
2. synchronous , synchronous

3. asynchronous, asynchronous

4. asynchronous, synchronous

453. We can usually obtain the Thevenin equivalent in the time

domain.
1. True

2. False
3. Some times

4. Incomplete Question

454. What are the number of samples present in an impulse

response called as?
1. length
2. string

3. array
4. element

455. What are the primary resources of an communication system

1.

Channel Bandwidth

2. noise

3.
power and Bandwidth

4.

Transmitted Power

456. What effect does a clamper have on the peak-to-peak value

of its input signal
1.No change
2. It decreases

3. It increases

4. zero

457. What is PSRR value of an ideal op-amp?

1. Zero

2. Unity

3. Infinite
4. Unpredictable

458. What is the approximate phase angle in a series RLC circuit

when VC = 117 V, VR = 14.5V, and VL = 3.3 V?
1.

45.0 degrees

2.

90.0 degrees

3.
82.7 degrees

4. –172.7 degrees

459. What is the current gain for a common-base configuration

where IE = 4.2 mA and IC = 4.0 mA?
1. 1.05

2. 16.80

3. 0.95
4. 0.20

460. What is the major factor for determining whether a medium

is free space, lossless dielectric, lossy dielctric or good conductor?
1. Attenuation Constant

2. Loss tangent
3. Complex permittivity

4. Reflection Coefficient.

461. What is the minimum number of gates required to

implement the Boolean function (AB+C) if we have to use only 2-
input NOR gates?
1. 5

2. 4

3. 2

4. 3

462. What is the nature of Fourier representation of a discrete &

aperiodic signal?
1. Continuous & periodic
2. Continuous & aperiodic

3. Discrete & periodic

4. Discrete and aperiodic

463. What is the number of channels of a cellular system with an

allocated spectrum of 25 MHz and with a channel of 30 kHz
bandwidth?

1.
833

2.

1000

3. 666

4.

240
 464. What is the range of magnitude of reflection coefficient due
to passive load
1. 0 to 1
2. 1 to infinity

3. 0.5 to 1

4. 0 to infinity

465. What is the resolution of a digital-to-analog converter (DAC)?

1. It is the comparison between the actual output of the converter and its expected output.

2. It is the difference between the input and output

3. It is its ability to resolve between forward and reverse steps when sequenced over its entire
range.

4. It is the smallest analog output change that can occur as a result of an increment in
the digital input.

466. What is the ROC of the Z-transform of x(n) = -(0.5)n u(-n-1) +

(0.2)n u(n) + (0.8)n u(n)?
1. ROC does not exist
2. |z| > 0.8

3. |z| < 0.5

4. |z|> 0.5 and |z| < 0.8

467. What is the theoretical range of VSWR

1. 1 to infinity
2. 0 to 1

3. - infinity to + infinity

4. -1 to 1

468. What is the unit of magnetic charge?

1. A-m
2. Ampere

3. A-m2

4. Coulomb

469. What is the Vs for a series RLC Circuit when IT = 3 mA, VL =

30V, VC = 18V, and R =1KΩ
1.

34.98 V

2. 48.00 V

3.

3.00 V

4.
12.37 V

470. What is VSWR for short-circuited transmission lines

1. 10

2. 5

3. 1

4. infinity

471. What type of diode circuit is used to add or restore a dc level

to an electrical signal?
1. clipper or limiter
2. clamper
3. IC voltage regulator

4. Quantizer

472. What type of diode is commonly used in electronic tuners in

TVs?
1. Schottky

2. LED

3. Gunn

4. varactor

473. What would be the power factor for an RLC circuit that acts
inductively?

1.

+90 degrees leading

2.

one

3.
zero

4. –90 degrees lagging

474. When a silicon diode is forward biased, what is VBE for a C-E
configuration?
1. emitter voltage

2. voltage-divider bias
3. 0.4 V

4. 0.7 V

475. When compared a 1st order LPF with a 2nd order LPF has
1.
Higher cut off frequency

2. Faster drop in filter response

3.

Lower voltage gain.

4.

Higher voltage gain.

476. When port 1 of a two-port circuit is short-circuited, I1 = 4I2

and V2 = 0.25I2. Which of the following is true?
1.

y21 = 16

2.
y12 = 16

3.

y11 = 4

4. y22 = 0.25
 477. When the input is symmetrical, to operate the BJT in active
region, the quiescent point is chosen
1. at the bottom edge of the load line

2. can be chosen any where on the load line

3. at the centre of the load line

4. at the top edge of the load line

478. When the modulating frequency is doubled, the modulation

index is halved, and the modulating voltage remains constant. The
modulation system is
1. Frequency Modulation
2.phase shift keying modulation 3. Phase Modulation

4. Amplitude Modulation

479. When transistors are used in digital circuits they usually

operate in the ________
1. linear region

2. active region

3. breakdown region

4. saturation and cutoff regions

480. When XC = XL the circuit:

1. draws minimum current 2. draws maximum current

3.

applied voltage is zero

4.
is at resonance

481. Which among the below assertions is precise in accordance

to the effect of time scaling ?
A : Inverse relationship exists between the time and frequency domain representation of signal

B : A signal must be necessarily limited in time as well as frequency domains

1. Both A & B are true

2. A is false & B is true

3. Both A & B are false

4. A is true & B is false

482. Which among the following assertions represents a

necessary condition for the existence of Fourier Transform of
discrete time signal (DTFT)?
1. Discrete time signal should be absolutely multipliable

2. Discrete time signal should be absolutely differentiable

3. Discrete time signal should be absolutely integrable

4. Discrete time signal should be absolutely summable

483. Which are the only waves that correspond/ support the
measurement of phase angle in the line spectra?
1. Cosine waves
2. Triangular waves

3. Square waves

4. Sine waves
 484. Which code is used to spread the signal across the places
1.

Walsh code

2. randaom noise 3. Fast code

4.
Pseudo-noise code

485. Which coding technique/s exhibit/s the usability of fixed

length codes?
1. Turbo Code

2. Huffman

3. Lempel Ziv
4. Convolution code

486. Which is the higher gain provided by a C-E configuration?

1. voltage

2. Power
3. current

4. resistance

487. Which is the type of antenna used in OFDM technique?

1. Smart Antenna

2. Micro Strip Antenna

3. Log Periodic
4. Yagi Uda

488. Which mode is known as dominant mode for Rectangular

waveguide
1. TM10 and TE10

2. TM10
3. TM11

4. TE10

489. Which modulation scheme has the lowest probability of

error?
1. QPSK
2. Non-coherent FSK

3. DPSK

4. Coherent FSK

490. Which modulation technique is not suitable for audio, video

but is used for transmission of telephone signals?
1. SSB-SC
2. VSB-SC

3. AM

4. DSB-SC

491. Which modulation technique transmits at higher data rate

1.

QPSK

2. 32PSK
3.

BPSK

4.

16-PSK
 492. Which of the concepts is used to find the expression of
related E and H field due to a magnetic current element?
1. Concept of scalar electric potential

2. Concept of vector magnetic potential

3. Concept of scalar magnetic potential

4. Concept of vector electric potential

493. Which of the following analog modulation scheme requires

the minimum transmitted power and minimum bandwidth?

1.

DSB-SC

2. AM

3. SSB
4.

VSB

494. Which of the following circuit can be used as parallel to serial

converter ?
1. Digital counter

2. Decoder

3. Demultiplexer

4. Multiplexer

495. Which of the following combinations cannot be combined

into K-map groups?
1. Overlapping combinations

2. Diagonal corners
3. Corners in the same row

4. Corners in the same column

 496. Which of the following is NOT a common light detector
1. PIN photodiode

2.Zener diode

3. Photodiode
4. Avalanche photodiode

497. Which of the following is NOT associated with a PN junction?

1. Charge storage capacitance

2. Depletion capacitance

3. Channel length modulation

4. Junction capacitance

498. Which of the following is the main advantage of PCM system

1.

Lower power

2. High power 3. Lower Bandwidth

4.
Lower noise

499. Which of the following is the most reliable measurement for

comparing amplifier noise characteristics?
1. Thermal Noise Agitation

2. Shot Noise

3. Signal to Noise ratio

4. Noise Factor

500. Which of the following is true about the AM and FM

systems?
1. BW of FM < BW of AM; power FM > power AM; noise FM > noise AM

2. BW of FM < BW of AM; power FM < power AM; noise FM < noise AM

3. BW of FM < BW of AM; power FM > power AM; noise FM < noise AM

4. BW of FM > BW of AM; power FM < power AM; noise FM < noise AM

501. Which of the following lines is non-radiating?

1.parallel wire

2. waveguide

3. Open two wire

4. Coaxial

502. Which of the following methods can be used for generating

SSB-SC signals?
1. Ring Modulator

2. Frequency Discrimination Method

3. Switching modulator

4. Square-law modulator

503. Which of the following potential expression does satisfy

Laplace’s Equation:
1. V1 = ρzsinϕ +ρ2

2. V1 = x2+y2+5z2-10
3. V1 = x2+y2-2z2 +10

4. V1 = 2x2+5

504. Which of the following pulse modulation is analog?

1. Differential PCM
2. PWM
3. Delta

4. PCM

505. Which of the matching network is having higher bandwidth

for a given load.
1. Quarter wave matching

2. Single stub shunt matching

3. Single stub series matching

4. Double stub matching

506. Which of these Controls call processing and status

management of the BTS, as the highest-level processor within the
BTS.
1. TFPA

2. GPS-R

3. BSPA
4. TFBB

507. Which of these trasmission line supports Quasi-TEM mode

1.
Microstrip line

2. Strip line

3. Microstrip line and Stripline Both

4. Parallel Plate waveguide

508. Which of this Controls FSU power during call?

1. Order wire

2. APC Channel
3. Traffic Channels

4. Access Channel
 509. Which one is channel coding technique?
1. Arithmetic coding

2. Convolutional Codes
3. Shannon Coding

4. Huffman coding

510. Which one of the following blocks is not common in both AM

and FM receiver?

1.

IF amplifier

2.

Mixer

3.

RF amplifier

4. Slope detector

511. Which one of the following is used to detect the unknown

signal
1.

Coherent BPSK
2. DPSK
3.

QPSK

4.

Coherent BFSK

512. Which one of the following statements regarding the signal:

X(t) = 5sin(2π103t)sin(2π106t) is correct?
1. Upper side band frequency is 1001000

2. Lower side band frequency is 999000

3. X(t) is a DSB ? SC signal

4. All of these

513. Which one of these statements is not characteristic of static

magnetic field:

1. It is conservative
2. Magnetic flux lines are always closed.

3. It is solenoidal

4. It has no sinks or sources

514. Which performance parameter of a regulator is defined as

the change in regulated load voltage due to variation in line
voltage in a specified range at a constant load current?
1. Temperature stability factor

2. Line regulation
3. Load regulation
4. Ripple rejection

515. Which phenomenon occurs due to an increase in the channel

bandwidth during the transmission of narrow pulses in order to
avoid any intervention of signal distortion?
1. Expansion in frequency domain
2. Compression in frequency domain

3. Compression in time domain

4. Expansion in time domain

516. Which statement best describes reactance in a series RLC

circuit?

1. The larger of the two reactance is dominant 2. Resistance is always dominant

3.

Inductive reactance is always dominant

4.

Capacitive reactance is always dominant

517. Which statement is false for Admittance smith chart.

1. Left of the smith chart is open circuit end

2. VSWR at centre of smith chart is 2

3. Right of the smith chart is short circuit end

4. Reflection coefficietn at centre of smith chart is 1

 518. Which technology has a longer handset battery life?

1. TDMA

2. FDMA/TDMA

3. CDMA
4. SDMA

519. Which type of fiber optic cable is best for very high speed
data?
1. single-mode step-index
2. multimode step-index

3. single-mode graded-index

4. multimode graded-index

520. Which type of gate can be used to add two bits?

1. NOR

2. EX-NAND

3. EX-OR
4. EX-NOR

521. Which type/s of Fourier Series allow/s to represent the

negative frequencies by plotting the double-sided spectrum for the
analysis of periodic signals ?
1. Exponential Fourier Series
2. Trigonometric Fourier Series

3. All types specified

4. Polar Fourier Series

 522. Why are the negative & positive phase shifts introduced for
positive & negative frequencies respectively in amplitude and
phase spectra?
1. To maintain the amplitude spectrum

2. To maintain the symmetry of the phase spectrum

3. To change the symmetry of the phase spectrum

4. To change and maintain the symmetry of the phase spectrum

523. Why GMSK is preferred over MSK in Wireless

Communication?
1. Constant Envelope property
2. Time spread of frequency-shaping pulse

3. Better out-of band spectral characteristics

4. Wider bandwidth

524. Wiener-Khintchine relationship is between

1. Energy Spectral Density and Fourier transform of a signal

2. Fourier transform of a signal and its autocorrelation

3. Power Spectral Density and Auto-correlation function of a random process

4. Power Spectral Density and Energy Spectral density of a random process

525. With a 12 V supply, a silicon diode, and a 370-ohm resistor in

series, what voltage will be dropped across the diode?
1. 0.3 V

2. 0.9 V

3. 1.4 V
4. 0.7 V

526. With a 200 kHz clock frequency, eight bits can be serially
entered into a shift register in
1. 40 μs
2. 400 μs

3. 40 ms

4. 4 μs

527. With a half-wave rectified voltage across the load resistor,

load current flows for what part of a cycle?
1. 90 degrees

2. 360 degrees

3. 180 degrees
4. 0 degrees

528. With a PNP circuit, the most positive voltage is probably

______
1. VCC

2. ground
3. VC

4. VBE

529. With respect to the envelopes of the AM and FM modulated

waves, which of the following is true?
1. Both vary according to the shape of the message signal

2. Envelope of AM is constant, FM is variable

3. Both are of constant amplitude

4. Envelope of AM varies and FM envelope is constant

530. Yagi antenna is

1. broadside array
2. circular array

3. planar array

4. end fire array

531. Zero initial condition for a system means

1. input reference signal is zero

2. zero stored energy

3. initial movement of moving parts

4. system is at rest and no energy is stored in any of its components

532. “A” register of 8051 is of ___ bit wide and it is loaded with
the default value of ___ after reset.
1. 16,00

2. 16,0000

3. 8,07

4. 8,00

533. If an op-amp comparator has a gain of 100,000, an input

difference of 0.2 mV above reference, and a supply of 12 V, the
output will be
1. 20V

2. 12V
3. 15V

4. 10V
 534. In a ________, when the input voltage exceeds a specified
reference voltage, the output changes state.
1. integrator

2. comparator
3. differentiator

4. summing amplifier

535. In a flash A/D converter, the priority encoder is used to

1. select the last input.

2. select the lowest value input.

3. select the highest value input.

4. select the first input.

536. The signal cos ωct – 0.5cos ωmt sin ωct

1.FM only

2.AM only

3.both AM and FM
4.neither AM or FM

537. Assuming that the channel is noiseless, if TV channels are 8

kHz wide with the bits/sample = 3Hz and signaling rate = 16 × 106
samples/second, then what would be the value of data rate?

1.

16 Mbps

2.

24 Mbps
3.
48 Mbps

4.

64 Mbps

538. Which among the following is used to construct the binary

code that satisfies the prefix condition?

1.

Information Rate

2.

Noiseless Channel

3.

Channel Coding Theorem

4.
Kraft Inequality

539. If the autocorrelation function of a random process X(t) is

given by RX(τ)=exp(-2|tau|)u(tau) . Power spectral density of X(t) is

1.

1/(1 + 4π2f2)
2.

1/(1 + π2f2)

3.

1/(4 + π2f2)

4.

4/(4 + 4π2f2)

540. The most suitable method for detecting a modulated signal

(2.5 + 5 cos ωmt) cos ωct is:

1.
Envelope detector

2.

Synchronous detector

3.

Ratio detector

4.

Both Envelop and Synchronous detector

 541. Signal travel through various paths and arrives at receivers at
different time multi path propagation.
1.Additive noise Channel

2.Linear Filter Channel.

3.Linear Time-Variant Filter Channel.

4.Linear Time Invariant Filter

542. ____ PORT in 8051 is requiring external pull up resistor

network

1. PORT12

2. PORT3

3. PORT0
4. PORT1

543. 1. Why micro controllers are not called general purpose

devices?

1.

because they are based on VLSI technology

2.
because they are not meant to do a single work at a time

3.

because they are cheap

4.

because they consume low power

 544. 1. In 8 bit signed number operations, OV flag is set to 1 if:

1.

a carry is generated from D7 bit

2.

a carry is generated from D3 bit

3.

a carry is generated from D7 or D3 bit

4.
a carry is generated from D7 or D6 bit

545. 1. In unsigned number addition, status of which bit is

important?

1.

OV

2.
CY
3.

AC

4.

PSW
 546. What is the unit of responsitivity?
1.
Ampere/watt

2.

Ampere/Volt

3.

Watt/Ampere

4.

Votl/Ampere

547. What is the spectral width of a standard LED?

1. 20 to 40nm

2. 30 to 50 nm

3.

40 to 60nm

4.

10 to 50nm

548. SP of 8051 is of ___ wide and it is loaded with the default

value of ___ after reset

1.4 bit,00H
2.8 bit,07H
3.8 bit,00H

4.

32 bit,00H

549. Width of the main spectral lobe, where most of the signal
power is contained.

1.Half Power Bandwidth

2.Null to Null Bandwidth

3. Absolute Bandwidth

4.Full Power Bandwidth

550. An amplifier for which design was done with A =100 and
β=0.01 is manufactured using an amplifier with half the intended
gain. Find the sensitivity of the closed loop to open loop gain in
dB?
1.

55.25%

2.

70%

3.

13%

4.

67%
 551. AA command adds 6 to the nibble if:

1.

CY and AC are necessarily 1

2.
either CY or AC is 1

3.

no relation with CY or AC

4.

CY is 1

552. 1. When we add two numbers the destination address must

always be.

1.

some immediate data

2.

any register

3.
accumulator

4.

memory
 553. 1. A micro controller at-least should consist of:

1.

RAM, ROM, I/O devices, serial and parallel ports and timers

2.

CPU, RAM, I/O devices, serial and parallel ports and timers

3.
CPU,RAM, ROM, I/O devices, serial and parallel ports and timers

4.

CPU, ROM, I/O devices and timers

554. 1. On power up, the 8051 uses which RAM locations for
register R0- R7

1.

00-2F

2.

00-07
3.
00-7F

4.

00-0F

555. 1. What is the clock source for the timers?

1.

some external crystal applied to the micro-controller for executing the timer

2.
from the crystal applied to the micro-controller

3.

through the software

4.

through programming

556. 1. What is the order decided by a processor or the CPU of a

controller to execute an instruction?

1.

decode,fetch,execute
2.

execute,fetch,decode

3.

fetch,execute,decode

4.
fetch,decode,execute

557. a) Consider the figure given below. The given amplifier is

showing nonlinear behavior with A =104 V/V for Vo <= 0.2 V , A=
103 V/V for 0.2 V < Vo < 1 V but it hard limits at Vo =1 V. The β of
feedback loop is 0.01. Find the closed loop gain when 0.2 V

1.

90.9

2.

91.9
3.
99

4.

89.9

558. An amplifier using an op-amp with a slew rate of 1V/µ has a

gain of 60 dB. If the amplifier has to faithfully amplify the
sinusoidal signals from DC to 40 KHz without introduced any slew
rate induced distortion, then the input signal must not exceed
what value?

1.

25.53 mV

2.
3.98 mV

3.

34.4 mV

4.

32.89 mV
 559. Find the cut off frequency for the filter circuit given below

1.

1000 rad/sec

2.

A) 2000 rad/sec

3.

A) 200 rad/sec

4.

A) 100 rad/sec

560. The op- amp circuit shown below is a certain class of filter.
Find the type of the filter
1.

A) High Pass Filter

2.

A) Low Pass Filter

3.

A) Band Reject Filter

4.

A) Band Pass filter

561. A 741 op-amp has a gain bandwidth product of 1 MHz. A non

inverting amplifier using this op-amp and having a voltage gain of
40 dB will exhibit a 3 dB bandwidth of how much?
1.

100 kHz

2.

300 kHz
3.

10 kHz

4.

500 kHz

562. For the given circuit below for the cut off frequency of 3 kHz
find the value of R2

1.

4.5 kOhm

2.

10.61 kOhm

3.

3.4 kOhm
4.

1.9 kOhm

563. For the transfer function given below find the gain at very
low frequencies (assume DC).

1.

100

2.

3.

10

4.

564. Total recombination lifetime in direct bandgap

semiconductors…………………..than that of indirect bandgap
semiconductors
1.

more
2.
less

3.

Equal

4.

Equal or more

565. If the gain margin of a certain feedback system is given as 20

dB, the Nyquist plot will cross the negative real axis at the point

1.

s = - 0.05

2.

s = - 0.2

3.

s = - 0.1

4.

s = -0.01
 566. Bragg’s law in X-ray diffraction assumes ---------- of X-rays
from successive planes of atoms
1.
Reflection

2.

Transmission

3.

Absorption

4.

Rotation

567. Frank Condon principle is used for the interpretation of the

intensity of
1.

Pure rotational spectra

2.
Vibrational spectra

3.

Raman spectra

4.

Microwave spectra
 568. One electron wave function for an electron in an atom is
called
1.

Angular momentum

2.

Hamiltonian Operator

3.Atomic orbital
4.

Linear momentum

569. The system function H(z) = (z3-2z2+z)/(z2+0.25z+0.125) is,=

1.

Causal

2.

Unstable but causal

3.
Noncausal

4.

Cannot be defined

570. .__________ and ________are the two 16 bit registers in

8051
1.
PC and ACC

2.
PC and DPTR

3.

IE and PC

4.

ACC and B

571. Serial data bits being received are initially stored in

1.

R0

2.

ACCUMLATOR

3.
SBUF
4.

TF0

572. RETI instruction clears the following flags

1.

TF0,RI

2.

TF0,TI
3.
TF0,IE0
4.

RI,TI

573. What form of waveform is shown here?

1.

a multi-valued digital signal

2.

a binary signal

3.

an analogue signal

4.

a digital signal
 574. A sinusoidal signal is passed through an amplifier and results
in the following waveform. What form of distortion is
predominant?

1.

Barrel distortion

2.
Crossover distortion

3.

Clipping

4.

Harmonic distortion

575. δ[n] =
1.

u[n]
2.
u[n]-u[n-1]

3.

u[n-1]

4.

u[-n]

576. How many longitudinal modes can fall within a laser’s gain
bandwidth?
1.

2.

3.

4.
No fixed limit, dependent on bandwidth and mode spacing

577. The speed of light in plastic compared to the speed of light in

air is
1.
Slower
2.

. Faster

3.

The same

4.

Either lower or faster

578. A current of 3+j4 amperes is flowing through the circuit.The

magnitude of the current is _______
1.7 A 2.1 A 3.5 A 4.1.33 A

579. A feedback arrangement is shown in figure below. If Xo = 4.0

V, Xf = 0.9 V , Xs= 1.00 V. Find A

1.

a) 30
2.
a) 40

3.

a) 50

4.

a) 60

580. A feedback arrangement is shown in figure below. If Xo = 4.0

V, Xf = 0.9 V , Xs= 1.00 V. Find β.

1.

a) 0.25

2.
a) 0.225

3.

a) 0.3
4.

a) 0.4

581. A feedback arrangement is shown in figure below. If Xo = 4.0

V, Xf = 0.9 V , Xs= 1.00 V. Find Xi.

1.

0.01 V

2.
0.1 V

3.

0.02 V

4.

0.001 V
 582. A feedback arrangement is shown in figure below. If Xo = 4.0
V, Xf = 0.9 V , Xs= 1.00 V. Find the amount of feedback.

1.
a) 10

2.

3.

100

4.

90

583. A good measure of similarity between two signals x1(t) and

x2(t) is
1.

convolution
2.
correlation

3.

power density spectrum

4.

fourier transform

584. A network contains linear resistors and ideal voltage

sources.If the value of all the resistors are doubledthen the voltage
across each resistor_______
1.not changed
2.increases four times

3.doubled

4.halved

585. A network function can be completely specified by:

1.Real parts of zeros

2.Poles and zeros

3.Real parts of poles

4.Poles, zeros and a scale factor

586. A network function contains only poles whose real-parts are

zero or negative. The network is

1.always stable

2.stable, if the jw-axis poles are simple

3.stable, if the jw-axis poles are at most of multiplicity 2
4.always unstable

587. A network has 7 nodes and 5 independent loops. The

number of branches in the network is:
1.13 2.12 3.11 4.10

588. A network N is to be connected to load of 500 ohms. If the

Thevenin’s equivalent voltage and Norton’s equivalent current of N
are 5Volts and 10mA respectively, the current through the load will
be
1. 10mA

2. 2.5mA

3. 5mA
4. 1mA

589. A open loop transfer function is given as G(s) = (s+2)/(s+1)(s-

1). Find the number of encirclements about ‘-1+j0’?
1.
1

2.

3.

4.

590. A signal x(t) = A cos(omega_0 t+phi) is

1.
An energy signal

2.

A power signal

3.

Energy as well as power signal

4.

Neither energy nor power signal

591. A signal x(t) has Fourier transform X(j omega). If x(t) is a real
and even function of t, then X(j omega) is
1.
A real and even function of omega

2.

Imaginary and odd function of omega

3.

An imaginary and even function of Omega

4.

A real and odd function of Omega

 592. A source of angular frequency 1 rad/sec has source
impedance consisting of 1Ω resistance in series with 1H
inductance. The load that will obtain the maximum power transfer
is:
1.1O resistance 2.1O resistance in parallel with 1H inductance 3.1O resistance in parallel with 1F
capacitor 4.1O resistance in series with 1F capacitor

593. A source of angular frequency 1 rad/sec has source

impedance consisting of 1 ohm resistance in series with 1 H
inductance. The load that will obtain the maximum power transfer
is:
1.

1 ohm resistance

2.

1 ohm resistance in parallel with 1H inductance

3.

1 ohm resistance in parallel with 1F capacitor

4.
1 ohm resistance in series with 1F capacitor

594. A system with an input x(t) and output y(t) is described by

the relation y(t) = tx(t). This system is
1.

Linear, time invariant

2.
Linear, time variant
3.

nonlinear , time invariant

4.

non linear, time variant

595. A system with gain margin close to unity or a phase margin

close to zero is
1.highly stable

2.unstable

3.relatively stable

4.oscillatory

596. A uniform plane electromagnetic wave incident normally on

a plane surface of a dielectric material is reflected with a VSWR of
3 .what is the percentage of incident power that is reflected ?
1.10%

2.25%
3.75%

4.50%

597. A unit impulse voltage is applied to one port network having

two linear components. If the current through the network is 0 for
t<0 and decays exponentially for t>0 then the network consists of
1.R and L in series 2.R and L in parallel 3.R and C in parallel 4.R and C in series

598. A unity feedback control system has an open loop transfer

function G(s) = k/(s(s² + 7s + 12) The gain k for which s = -1 + j1 will
lie on the root locus of the system is
1.
4

2.

6.5

3.

4.

10

599. After RETI instruction is executed then the pointer will move
to which location in the program?
1.

next interrupt of the interrupt vector table

2.
next instruction of the program after the IE instruction

3.

next instruction after the RETI in the memory

4.

First Instruction of the program

 600. An amplifier whose open loop response is characterized by a
dc gain of 105 V/V and a 3 dB roll off at 20 KHz, is connected in a
feedback loop for which the overall low frequency gain is 100V/V.
what is the 3 dB roll-off with feedback?
1.

A) 10 MHz

2.

A) 30 MHz

3.

A) 20 MHz

4.

A) 40 MHz

601. An L-C impedance or admittance function:

1.has simple poles and zeros in the left half of the s-plane

2.has no zero or pole at the origin or infinity.

3.has all poles on the negative real axis of the s-plane.

4.is an odd rational function.

602. Assuming zero initial condition, the response y(t) of the

system given U(s)->1/s->Y(s) to a unit step input u(t) is
1.u(t) 2.e-tu(t) 3.t^2/2*u(t) 4.tu(t)

603. Both NMR and NQR spectra are observed in ---------- region
1.

Microwave

2.
Radiofrequency

3.

X-ray

4.

UV-Vis

604. Calculate the cutoff frequency of a first-order low-pass filter

for R1 = 2.5 k and C1 = 0.05 F.
1.

1.273 kHz

2.
12.73 kHz

3.

127.3 kHz

4.

127.30 Hz

605. Calculate the output voltage if V1 = –0.2 V and V2 = 0 V.

1.

0V

2.

6.6 V

3.

4V

4.
2V

606. Conductor loss in Microstrip line will be less if

1.width of line is large 2.width of line small 3.height of substrate is more 4.height of
substrate is less

607. Consider a network function H(s) = 2(s+3)/((s+2)(s+4)). What

is the steady state response due to step input?
1.

4/3

2.

3.

1
4.
¾

608. Consider the figure given below. The given amplifier is

showing nonlinear behavior with A =104 V/V for Vo <= 0.2 V , A=
103 V/V for 0.2 V < Vo < 1 V but it hard limits at Vo =1 V. The β of
feedback loop is 0.01. Find Vi when Vo=0.99 V.

1.

a) 0.9 mV

2.

a) 0.099 mV

3.
a) 0.99 mV

4.

2.5 mV
 609. Continuous time non periodic signal has
1.

Periodic continuous spectra

2.

Aperiodic discrete spectra

3.

Aperiodic continuous spectra

4.
Periodic discrete spectra

610. Convolution of x(t+5) with impulse function \delta(t-7) is

equal to
1.

x(t-12 )

2.

x(t+12)

3.
x(t-2)

4.

x(t+2)
 611. Determine the output voltage for this circuit with a sinusoidal
input of 2.5 mV.

1.

0.25 V

2.

0.125 V

3.

0.25 V

4.
-0.125 V

612. Determine the output voltage when V1 = –V2 = 1 V.

1.

0V

2.

2V

3.

1V

4.
-2 V

613. During Bhopal tragedy the gas released was

1.

Phosgene

2.
Methyl isocyanate

3.

Potassium isothiocyanate
4.

Ammonia

614. Electron transfer from Fe(H2O)62+ to Fe(H2O)63+ is likely

occur via
1.
d-d transitions

2.

Inner sphere electron transfer

3.

SN1 mechanism

4.

Outer sphere electron transfer

615. Find the zero of the transfer function given

1.
(-1,-2)

2.

a) (1,2)
3.

a) (2,-1)

4.

a) (1,4)

616. Fisher’s indole synthesis involves

1.

[2, 3] sigmatropic shift

2.
[3, 3] sigmatropic shift

3.

[3, 2] sigmatropic shift

4.

[2, 2] sigmatropic shift

617. Flat-top sampling of low pass signals

1.
give rise to apperture effect

2.

Implies oversampling

3.
Leads to aliasing

4.

Introduces delay distortion

618. For serial communication, standard frequency of the crystal

for 8051 would be
1.11.0592 MHz 2.11.0952 MHz

3.11.0295 MHz

4.11MHz

619. For a RC circuit, the power factor is ________

1. 0

2. 1

3. between 0 and 1
4.>1

620. For a RL circuit, the power factor is ________

1.0 2.1 3.Between 0 and 1 4.>1

621. For a series R-C circuit excited by a d-c voltage of 10V, and
with time-constant t, s, the voltage across C at time t = t is given by
1.10(1-e^-1) V 2.10-e^-1 V 3.10(1-e) V 4.1-e^-1 V

622. For a type one system, the steady – state error due to step
input is equal to
1.0.5 2.infinite 3.0.25 4.zero
 623. For addition or subtraction of phasors,we use ______ form
1.Trignometrical 2.Rectangular 3.Polar 4.Trignometrical and polar

624. For an ideal transformer,

1.both z and y parameters exist.
2.neither z nor y parameters exist.

3.z-parameters exist, but not the y-parameters.

4.y-parameters exist, but not the z-parameters.

625. For the circuit given below Find out what is the type of
feedback? Also find out the feedback factor (assume that and r=5
k and R2= 10 K and R1=20 K)

1.Series-Series. 3.34 X 10^(3) 2.Series-Shunt, 2.54 X 10^(3) 3.

Shunt-Series, 2.45 X 10^(3)

4.

Shunt-Shunt, 4.67 X 10^(3)

 626. For the circuit given below find out what type of feedback
configuration it is. Also find out the feedback factor (assume that
and r=5 k and R2= 10 K)

1.

A) Series-Series, 0.25

2.

A) Series-Shunt, -0.25

3.

Shunt-Series, -0.5

4.
A) Shunt-Shunt, 0.5
 627. Fourier transform of impulse function is

1.
1

2.

3.

4.

Can not be found

628. Fourier transform of u(t) is

1.

2/(j omega)

2.
1/(j omega)

3.

1/ (j omega)

4.

1
 629. How are the bits of the register PSW affected if we select
Bank2 of 8051?
1.

PSW.5=0 and PSW.4=1

2.

PSW.2=0 and PSW.3=1

3.

PSW.3=1 and PSW.4=1

4.
PSW.3=0 and PSW.4=1

630. How is the status of the carry, auxiliary carry and parity flag
affected if write instruction
MOV A,#9C

ADD A,#64H

1.

CY=0,AC=0,P=0

2.

CY=1,AC=1,P=0

3.

CY=0,AC=1,P=0

4.

CY=1,AC=1,P=1
 631. How many bytes of bit addressable memory is present in
8051 based micro controllers?
1.

8 bytes

2.

32 bytes

3.
16 bytes

4.

128 bytes

632. How many op-amps are required to implement this

equation?

1.
2

2.

3.
4

4.

633. Ideal physical antenna length is ________ than its electrical

length.
1.greater

2.very smaller
3.smaller

4.equal

634. If a network function has zeros only in the left-half of the s-

plane, then it is said to be
1.a stable function.

2.a non-minimum phase function

3.a minimum phase function.

4.an all-pass function.

635. If a signal f(t) has an energy E, the energy of the signal f(2t) is
equal to
1.

2.
E/2
3.

2E

4.

4E
 636. If f(t) = f(-t) and f(t) satisfies the Dirichlet’s conditions, then
f(t) can be expanded in a Fourier series containing
1.
Only sine terms

2.

Only cosine terms

3.

Cosine terms and constant term

4.

Sine terms and a constant term

637. If periodic signal has odd symmetry, then the Fourier series
contains
1.
only sine terms

2.

Only cosine terms

3.

Both sine and cosine terms

4.

Multiply of Cosine and Sine terms

 638. If the Fourier series coefficients of x(t) are c_n , then the
Fourier series coefficients of x(-t) is given by

1.

c^*_n

2.

c_-n

3.

c^*_-n

4.

c_n

If the Nyquist plot of the loop transfer function G(s) H(s) of a closed-
loop system encloses the (-1, jo) point in the G(s) H(s) plane, the
gain margin of the system is
1.less than zero 2.greater than zero 3.Zero 4.infinity

639. If the periodic signal has an even symmetry, then the Fourier
series contains,

1.

Only sine terms

2.
Only cosine terms

3.

Constant and cosine terms

4.

Both sine and cosine terms

640. If two system with impulse responses are h1(t) and h2(t)
connected in parallel then the overall impulse response is
1.

h1(t) * h2(t)

2.
h1(t) + h2(t)

3.

h1(t) - h2(t)

4.

h1(t)h2(t)

641. If X(f) represents the Fourier transform of a signal x(t), which

is real and odd symmetric in time, then
1.

X(f) is complex
2.
X(f) is imaginary

3.

X(f) is real

4.

X(f) is real and non-negative

642. If x(t) and y(t) are two periodic signals, with Fourier series
coefficients c_n and d_n respectively, then the Fourier series
coefficients of z(t) = x(t)y(t) are
1.

c_n d_n

2.

Tc_n d_n

3.

c_n *d_n

4.

1/T c_n d_n

643. If x(t) is even, then its Fourier series coefficients must be

1.

real and odd

2.

imaginary and odd

3.

real and even

4.

imaginary and even

644. If x(t) is even, then X(j Omega) is

1.

Imaginary and even

2.

Imaginary and Odd

3.

Real and Even

4.

Real and Odd

645. If x(t) is odd, then X(j omega) is

1.

Imaginary and odd

2.

Imaginary and even

3.

Real and odd

4.

Real and even

646. In serial communication with 8051 Micro controller

________ timer &_____mode is used for baud rate generation
1.Timer 0 & Mode 1

2.Timer 1& Mode 0

3.Timer 0& Mode 2

4.Timer 1& Mode 2

647. In a 2-terminal network containing at least one inductor and

one capacitor, resonance condition exists only when the input
impedance of the network is:
1.purely resistive 2.purely reactive 3.infinite 4.finite

648. In a double tuned circuit, consisting of two magnetically

coupled, identical high-Q tuned circuits, at the resonance
frequency of either circuit, the amplitude response has
1.a peak, always 2.a dip, always 3.either a peak or a dip 4.neither a peak nor a dip

649. In a pure capacitive circuit,

1.current and voltage are in phase 2.voltage lags the current 3.voltage leads the current 4.no
relation between current and voltage
 650. In a pure inductive circuit with V=10 sin(1000 t) and L=0.05
H,the current in ampere is___
1.-0.2 cos(1000 t) 2.0.2 cos(1000 t) 3.-0.2 sin(1000 t) 4.0.2 sin(1000 t)

651. In a pure inductive circuit,

1.voltage leads the current 2.voltage lags the current 3.current and voltage are in phase 4.no
relation between current and voltage

652. In a pure inductive circuit,

1.voltage leads the current 2.voltage lags the current 3.current and voltage are in phase 4.no
relation between current and voltage

653. In BJT, the Q point on a dc load line in the saturation region

represents the
1. minimum current gain

2. cutoff point

3. intermediate current gain

4. maximum current gain

654. In differential-mode, …………….

1.opposite polarity signals are applied at the inputs 2.

the gain is one

3.

the outputs are of different amplitudes

4.

only one supply voltage is used

 655. In force-current analogy, electrical analogous quantity for
displacement (x) is
1.

voltage

2.

inductance

3.

capacitance

4.
flux

656. In the common mode, ……………

1.

both the inputs are grounded.

2.

the outputs are connected together

3.
an identical signal appears on both the inputs

4.

the output signals are in phase

 657. In the solution of network differential equations, the
constants in the complementary function have to be evaluated
from the initial conditions, and then the particular integral i is to be
added. This procedure is
1.correct. 2.incorrect 3.the one to be followed for finding the natural response 4.the
one to be followed for finding the natural and forced responses

658. MOV A, @ R1 will

1.

copy R1 to the accumulator

2.

copy the accumulator to R1

3.
copy the contents of memory whose address is in R1 to the accumulator
4.

copy the accumulator to the contents of memory whose address is in R1

659. Number of roots in left hand half of s plane if characteristic

equation is s3 - 4*s2 + s + 6 = 0 ?
1.
1

2.

3.

4.
0

660. Odd one out the following

1.

MOV PC,#0022h

2.

MOV DPTR,#0022H

3.

MOVC A,@A+DPTR

4.

MOV A,R0

661. One of the following is not a characteristic of light detectors

1.

Responsitivity

2.

Spectral response

3.

Transmit time

4.
Dispersion
 662. Point charges 30nC,-20nCand 10nC are located at (-
1,0,2),(0,0,0) and (1,5,-1), respectively. The total flux leaving a
cube of side 6m centered at the origin is
1.20nC 2.10nC3.30nC 4.-20nC

663. Solving –11 + (–2) will yield which two’s-complement

answer?
1.1111 0011 2.1111 1001 3.1110 1001 4.1110 1101

664. Specifications of Butterworth low pass filter are given as fp

=30kHz, Amax = 1 dB, fs = 40 kHz, Amin = 20 dB. What attenuation
is provided at 35 KHz ?

1.13.1 dB 2.

14.2 dB

3.9.3 dB 4.

40 dB

665. Specifications of butterworth low pass filter are given as fp =

30kHz, Amax = 1 dB, fs = 40 kHz, Amin = 20 dB. What is the order
of filter N?
1.

2.
11
3.

10

4.

14

666. Superposition theorem is applicable only to networks that

are:
1.linear. 2.time-invariant. 3.nonlinear. 4.passive.

667. Suppose a uniform electric field exists in the room in which

you are working, such that the lines of force are horizontal and at
right angles to one wall. As you walk toward the wall from which
the lines of force emerge into the room, are you walking toward
1.Points of different potential. 2.Points of the same potential (equipotential line)? 3.Points of
lower potential? 4.Points of higher potential?

668. Synchronous construction reduces the delay time of a

counter to the delay of
1.a single gate 2.all flip-flops and gates after a 3 count 3.all flip-flops and gates 4.a single flip-flop
and a gate

669. Technique gives quick transient and stability response

1.
Root locus

2.

Bode
3.

Nyquist

4.

Nichols

670. The vast majority of registers in 8051 are _________ bits

1.
8

2.

16

3.

32

4.

64

671. The 8051 can handle ________ interrupt sources.

1.

2.

4
3.

4.
6

672. The 8051 has ________ 16-bit counter/timers

1.

2.
2

3.

4.

673. The 8051 has ________ parallel I/O ports.

1.

2.

3
3.
4

4.

674. The 8051 Micro controller has inbuilt

1.

USART

2.
UART
3.I2C 4.

PWM

675. The admittance and impedance of the following kind of

network have the same properties:
1.LC 2.RL 3.PLC 4.RC

676. The amplitude spectrum of Gaussian pulse is

1.

Uniform

2.

Sine function

3.Gaussian function

4.

An impulse function
 677. The average power in a pure inductive load is _____
1.VmIm/2 2.VmIm/1.414 3.VmIm 4.0

678. The average power in a resistive circuit is given by

__________
1.0 2.VmIm 3.VmIm/1.414 4.VmIm/2

679. The average power in the RL circuit is ______ the average

power in a pure resistive circuit
1.Equal to 2.Greater than 3.lesser than 4.greater or equal to

680. The capacitance, in force-current analogy, is analogous to

1.

momentum

2.

velocity

3.

displacement

4.
mass

681. The characteristic equation of a control system is give by s(s +

4)(s² + 2s + 1) + k(s + 1) =0. Find the angle between the
asymptotes?
1.60°

2. 360°

3. 120° 4.180°

682. The clipper circuit is otherwise called as

1.

clampers

2.

Level Shifters

3.
Limiters

4.

DC restorers

683. The condition for maximum power transfer to take place in a

ac circuit is ___
1.ZL=-ZTH 2.ZL=ZTH* 3.ZL=ZTH 4.ZL=0

684. The contents of the accumulator after the following

operation
MOV A,#0BH

ANL A,#2CH

will be

1.
11010111

2.

11011010

3.

00001000

4.

00101000

685. The dc gain of a system represented by the transfer function

12 / {( s + 1 )( s + 3 )} is
1.

2.
2

3.

4.

10

686. The direct evaluation of DFT requires ______________

complex multiplications.
1.
N(N-1)

2.
N^2
3.

N(N+1)

4.

N(N-1)/2

687. The discrete time system described by y(n) = x(n^2) is

1.

causal, linear and time variant

2.

causal, linear, time invariant

3.
non-causal, linear, time invariant

4.

non-causal, linear, time variant

688. The Fourier series coefficients of the even part of x(t) are
1.

j Im {x_n}

2.

Re{c_n}

3.
Even {c_n}

4.

Odd {c_n}

689. The Fourier transform of odd signal is

1.

Real and even

2.

Imaginary and even

3.
Imaginary and odd

4.

Real and odd

690. The impulse response of a linear time invariant system is

given by h(n) = u(n+3) + u(n-2) -2u(n-7), where u(n) is unit step
sequence. The above system is
1.

stable, but not causal

2.

stable and causal

3.
causal, but unstable

4.

unstable, non causal

691. The input offset current equals the ……….

1.
difference between two bias currents

2.

average of two bias currents

3.

collector current divided by current gain

4.

addition of two bias currents

692. The input stage of an Op-amp is usually a ……….

1.
differential amplifier

2.

class B push pull amplifier

3.

CE amplifier
4.

Swamped Amplifier

693. The input-output relationship of a linear time invariant

continuous time system is given by r(t) = d²c(t)/dt² + 3 dc(t)/dt + 2
c(t) Where r(t) and c(t) are input and output respectively. What is
the transfer function of the system equal to?
1.

1/(s² + s + 2)

2.
1/(s² + 3*s + 2)

3.

2/(s² + 3*s + 2)

4.

2/(s² + s + 2)

694. The internal RAM memory of the 8051 is:

1.

32 bytes

2.

64 bytes

3.
128 bytes
4.

256 bytes

695. The minimum amount of hardware required to make a

lowpass filter is
1.a resistance, a capacitance and an opamp. 2.a resistance, an inductance and an opamp. 3.a resistance,
a capacitance and an inductance. 4.a resistance and a capacitance.

696. The number of complex multiplications required to calculate

N point DFT using radix-2 DIT-FFT algorithm is
1.

N log_2 N

2.

N/2 log_10 N

3.

N log_10 N

4.
N/2 log_2 N

697. The Nyquist sampling frequency in Hz of a signal given by 6 x

10^4 sinc(400\pit) x 10^6 sinc(100\pit) is
1.

200
2.
300

3.

500

4.

1000

698. The Nyquist sampling rate for the signal g(t) = 10 cos (50 pi t)
cos^2 (150 pi t), where t is in seconds is
1.

150 samples / sec

2.

200 samples/ sec

3.

300 samples / sec

4.

350 samples/ sec

699. The odd and even component of signal u(t) are

1.

cost, sint

2.
sint, -cos t

3.

(u(t) - u(-t))/2, (u(t) + u(-t))/2

4.

cost,-jsint

700. The open loop transfer function for unity feedback system is
given by 5(1+0.1s) / (s(1+5s)(1+20s)) Find the steady state error for
a step input of magnitude 10 is equal to
1.

2.
2

3.

infinite

4.

701. The open loop transfer function of a unity feedback control

system is given by G(s) = k/s(s+1). If gain k is increased to infinity,
then damping ratio will tend to become
1.
infinite

2.

0.707

3.

unity

4.
zero

702. The output of a particular Op-amp increases 8V in 12μs. The

slew rate is …….
1.90 V/μs

2.0.67 V/μs

3.

1.5 V/μs

4.

703. The phase margin of a system having the loop transfer

function G(s)H(s) = 2√3/s(s+1) is
1.

45°
2.
30°

3.

60°

4.

80°

704. The power factor is ____ for a pure inductor

1.0 2.1 3.between 0 and 1 4.>1

705. The power factor is ____ for a pure resistor

1.0 2.1 3.Between 0 and 1 4.>1

706. The power factor is given by _______

1.1/Cos x

2.tan x

3.sin x

4.Cos x

707. the power factor value is equal to 1 for a pure______

1.resistor 2.capacitor 3.inductor 4.voltage source

708. The Q-factor of a parallel resonance circuit consisting of an

inductance of value 1mH,capacitance of value 10^-5 F and a
resistance of 100 ohms is
1.1 2.10 3.20 4.100
 709. The rms value of the a-c voltage v(t) = 200 sin 314 t is:
1.200 V 2.157.23 V 3.314 V 4.141.42 V

710. The rms value of the sinusoidal wave is given by__

1.Vm/2 2.1.414 Vm 3.2Vm 4.vm/1.414

711. The second order system is defined by 25 / ( s2 + 5s + 25) is

given step input. The time taken for the output to settle with in 2
% of input is
1.

712. The second order system is defined by 25 / ( s2 + 5s + 25) is

given step input. The time taken for the output to settle with in 2
% of input is
2.

1.2 sec.

3.

2 sec.

4.

0.4 sec.

713. The signal x(t) = 2 cos (pi t) + 3sin (2t)

1.

is periodic

2.
is not periodic

3.

may or may not be periodic

4.

is periodic with certain conditions

714. The signal x(t) = e^(-2t)u(t) is

1.

power signal

2.
energy signal

3.

neither power nor energy

4.

either power or energy

715. The signal x[n] = cos (2n) is

1.

periodic with period pi

2.

periodic with period 2

3.

periodic with period 4\pi

4.

aperiodic

716. The system characterized by the equation y(t )= ax(t) + b is

1.linear for any value of b 2.linear if b > 0 3.linear if b < 0 4.non-linear

717. The system represented by h(n) = 0.99^n u(n+2) is

1.

unstable, because it is FIR system

2.
stable, because it is an IIR system

3.

unstable, because it does not obey BIBO stability criterion

4.

stable, because it obeys BIBO stability criterion

718. The system with impulse response h(t) = e^-6|t| is

1.

non-causal, stable

2.
non-causal, unstable
3.

causal, unstable

4.

causal, stable

719. The system y(n+2)+y(n+1) = x(n+2) is

1.

causal and memory less

2.

causal and has memory

3.

is causal

4.
is non-causal

720. The system y(t) = e^x(t) is

1.

stable, causal

2.

non-causal, stable

3.

non stable, causal

4.

unstable, non causal

721. The system y(t) = x(3t-6) is

1.

linear, time variant

2.

linear, time invariant

3.

non linear, time variant

4.

non linear, time invariant

722. The time period of the signal x(t) = cos (2*pi*t) + sin (5*pi*t)
is
1.

2 sec

2.

5 sec

3.
10 sec
4.

2.5 sec

723. The transfer function of a system given by

The system is

1.

an over damped.

2.
a critically damped.

3.

an under damped.

4.

a unstable.

724. The transfer function of phase lead compensator is given by

G(s) = (1 + TS)/(1 + αTS), where, T > 0, α < 0. What is the maximum
phase shit provided by this compensator?
1.
sin-1((1 - α)/(1 + α)

2.

cos-1((1 - α)/(1 + α)
3.

tan-1((1 - α)/(2√α)

4.

sin-1((1 - α)/(1 + α) and tan-1((1 - α)/(2√α)

725. The trigonometric fourier series of an even function of time

does not have the
1.

DC term

2.

Cosine term

3.
Sine term

4.

Odd harmonic temrs

726. the unit of average power is _____

1.Watts
2.Volt ampere 3.Newton 4.Volt ampere Reactive

727. The value of ‘a’ to give phase margin = 45° will be G(s) =
(as+1)/s²

1.

0.707
2.

1.414

3.

1.18

4.
0.9

728. To interface LCD to 8051 we need

1.

3 PORTS

2.
2 PORTS
3.

1 PORTS

4.

4 PORTS

729. To initialize any port as an output port what value is to be

given to it?
1.

0xFF

2.

0x11

3.
0x22

4.
A port is by default an output port

730. Two systems with impulse responses h1( t) and h2(t) are
connected in cascade.Then the overall impulse response of the
cascaded system is given by
1.convolution of h1( t) and h2(t)
2.sum of h1( t) and h2(t) 3.Product of h1( t) and h2(t) 4.subtraction of h1( t) and h2(t)

731. Using four cascaded counters with a total of 16 bits, how

many states must be deleted to achieve a modulus of 50,000
1.25,536 2.65,536 3.50,000 4.15,536

732. v1(t)=20 cos(wt+30),v2=30 sin(wt+45)

1.v2 leads v1 by -75 2.v1 leads v2 by 75 3.v2 leads v1 by 15 4.v1 leads v2 by 15

733. Vm=150 cos (200 pi t-30).The rms value is _____

1.128 2.106.1 3.156 4.110

734. Vr=10 cos (300 t),R=5 ohms; Ir=____

1.2/_0 2.10/_0 3.5/_0 4.60

735. w=200;L=0.5,the value of ZL=_____

1.100 2.-100j 3.100j 4.j/100

736. What is the address range of SFR Register bank?

1.
00H-77H

2.

40H-80H

3.

80H-7FH

4.
80H-FFH

737. What is the alternative function of P3.2 in 8051?

1.
INT 0
2.

INT 1

3.

COUNTER

4.

TIMER INTERRUPT

738. What is the disadvantage of a level triggered pulse?

1.

a constant pulse is to be maintained for a greater span of time

2.

difficult to analyse its effects

3.

it is difficult to produce

4.
another interrupt may be caused, if the signal is still low before the completion of the last
instruction

739. What is the highest frequency content of a triangle wave of

30-V peak-to-peak amplitude that can be exactly reproduced by an
op amp whose slew rate is 10 V/µs? Also For a sine wave of the
same frequency what is the maximum amplitude of output signal
that remain un-distorted?
1.
250 kHz, 6.37 V

2.

146 kHz, 5.45 V

3.

300 KHz, 3.54 V

4.

167 KHz, 9.53 V

740. What is the maximum size of the memory that can be

interfaced with 8051?
1.

16K

2.

32K

3.
64K
4.

128K
 741. When 8051 wakes up then 0x00 is loaded to which register?
1.

DPTR

2.

SP

3.
PC
4.

PSW

742. When a circuit is in resonance,the impedance of the circuit

is_____
1.XC 2.2R 3.XL 4.R

743. when a phasor is multiplied by –j,it is rotated through

________in the counter clockwise direction
1.90 2.180 3.45

4.Both magnitude and direction change

744. When any interrupt is enabled, then where does the pointer
moves immediately after this interrupt has occurred?
1.

to the next instruction which is to be executed

2.

to the first instruction of ISR

3.
to the first location of the memory called the interrupt vector table

4.

to the end of the program

745. When the micro controller executes some arithmetic

operations, then the flag bits of which register are affected?
1.
PSW
2.

SP

3.

DPTR

4.

PC

746. When two counters are cascaded, the overall MOD number
is equal to the ________ of their individual MOD numbers
1.Reciprocal 2.Log 3.Sum 4.Product

747. Which addressing mode is used in pushing or popping any

element on or from the stack?
1.

immediate

2.
direct

3.
indirect

4.

register

748. Which instruction is used to check the status of a single bit?

1.

MOV A,P0

2.

ADD A,#05H

3.
JNB PO.0, label

4.

CLR P0.05H

749. Which is the non-maskable interrupt in 8051?

1.

INT0

2.

INT1

3.

TIMER0

4.
RESET

750. Which of the following comes under indexed addressing

mode?
1.

MOVX A, @DPTR
2.
MOVC @A+DPTR,A
3.

MOV A,R0

4.

MOV @R0,A

751. Which of the following commands will copy the contents of

location 4H to the accumulator?
1.
MOV A, 04H
2.

MOV A, L4

3.

MOV L4, A

4.

MOV 04H, A

752. Which of the following commands will move the number 27H
into the accumulator?
1.

MOV A, P27

2.
MOV A, #27H
3.

MOV A, 27H

4.

MOV A, @27
 753. Which of the following instructions will load the value 35H
into the high byte of timer 0?

1.
MOV TH0, #35H
2.

MOV TH0, 35H

3.

MOV T0, #35H

4.

MOV T0, 35H

754. Which of the following is not the condition for existence of

Fourier transform
1.

x(t) must be absolutely integrable

2.

x(t) must have finite number of minima and maxima

3.

x(t) must have finite number of discontinuous points

4.

x(t) must be even signal

 755. Which of the following is not the property of Region of
convergence
1.

ROC can not have a pole

2.

ROC is right side of right most pole if x(t) is causal

3.

ROC can not have a zero

4.

ROC is left side of left most pole if x(t) is anti causal

756. Which of the following is the fastest light sensor

1.

PIN photodiode

2.

Photo voltaic photodiode

3.
Avalanche photodiode

4.

Photo transistor
 757. Which of the following statements will add the accumulator
and register 3?
1.

ADD @R3, @A

2.

ADD @A, R3

3.

ADD R3, A

4.
ADD A, R3

758. Which of the following system is time invariant

1.

y(t) = x(2t)

2.

y(t) = x(t) + x(t-1)

3.

y(t) = x(t/2)

4.

y(t) = x(-t)

759. which of the following systems are invertible?

1.

y(n) = nx(n)
2.

y(n) = x(n)x(n-1)

3.

y(t) = dx(t)/dt

4.

y(n) = x(1-n)

760. Which of the ports act as the 16 bit address lines for
transferring data through it?
1.

PORT 0 and PORT 1

2.

PORT 1 and PORT 2

3.
PORT 0 and PORT 2

4.

PORT 1 and PORT 3

761. Which operator is the most important while assigning any

instruction as register indirect instruction?
1.

$
2.

3.
@

4.

&

762. Which register is used to make the pulse a level or a edge

triggered pulse?
1.
TCON
2.

IE

3.

IPR

4.

SCON

763. Why would a delay gate be needed for a digital circuit?

1.to provide for setup times and hold times 2.to provide for hold times 3.to provide for setup
times 4.A delay gate is never needed.

764. x(t)*u(t) is equivalent to

1.

differentiating x(t)

2.

x(t) - x(t-1)
3.

accumulating x(t)

4.

x(t) + x(t+1)

765. Zth is 50 +30 j;what should be the load resistance connected

for maximum power transfer to take place?
1.50+30 j 2.50-30 j 3.-50-30j 4.-50+30j