Implementing an Analog-to-Digital Converter on
the Texas Instruments MSP430 Microcontroller
Karl Anderson April 5, 2013
ECE 480 Design Team 4
1 | Abstract
The MSP430 is a line of inexpensive and low-power microcontrollers (MCUs) produced
by Texas Instruments. These MCUs feature several peripherals that can be used to
accomplish a wide variety of tasks. One such peripheral is an analog-to-digital converter
(ADC) that can be used to measure and capture analog signals so they can be further
processed by the microcontroller. The ADCs that are featured in the various MSP430
devices have multiple channels to handle several analog input signals as well as
multiple modes of operation.
1.1 | Keywords
Analog-to-Digital Converter (ADC), Code Composer Studio (CCS), Microcontroller Unit
(MCU), Conversion Modes, Interrupt Service Routine (ISR), Interrupt, Timer, Control
Register
Page | 1
Table of Contents
1 | Abstract ................................................................................... 1
1.1 | Keywords .......................................................................... 1
2 | Introduction ............................................................................. 3
3 | Objective ................................................................................. 3
4 | Hardware & Software .............................................................. 4
5 | ADC Modes ............................................................................ 4
6 | ADC Conversion Process ………………………………………. 4
7 | ADC Registers ….................................................................... 6
8 | Configuring the ADC ............................................................... 7
9 | Conclusion .............................................................................. 8
10 | References ........................................................................... 8
Page | 2
2 | Introduction
The MSP430 line of microcontrollers from Texas Instruments features an 8-channel 10-
bit analog-to-digital converter (ADC). This means that the MSP430 can perform analog-
to-digital conversions on up to eight input signals with 10 bit resolution. This ADC is a
very powerful tool in many applications as it enables the MCU to measure analog input
signals so that they can be processed. This allows the MSP430 to dynamically respond
to analog inputs and perform various tasks based on these inputs. An example is a
control application where the MSP430 measures an analog sensor output and makes
decisions based on this changing analog value.
Figure 1. MSP430 LaunchPad
3 | Objective
The objective of this application note is to inform users about the ADC peripherals of the
MSP430 line of microcontrollers. Topics that will be covered include the various
operating modes and MCU registers associated with the ADC peripheral and software
configuration of the ADC with examples of code relating to various aspects of the ADC.
Page | 3
4 | Hardware and Software
Along with the MSP430 microcontroller, Texas Instruments also produces a
development board that is an essential tool for creating MSP430 applications called the
LaunchPad. It features on-board emulation for debugging the MSP430. The integrated
development environment (IDE) used to develop code for the MSP430 is TIs Code
Composer Studio (CCS). The LaunchPad can connect to a personal computer via a
mini-USB cable included with the LaunchPad, which will power the board and allow the
user to program and debug the MSP430. Once it has been programmed, the
microcontroller can be removed from the LaunchPad and installed in the system
designed for it.
5 | ADC Modes
The ADC featured on the MSP430 has four modes of operation: single channel single-
conversion, sequence-of-channels, repeat single channel, and repeat sequence-of-
channels. Below is a table describing each mode of the ADC.
Figure 2. ADC Conversion Modes
6 | ADC Conversion Process
The basic sequence of events that occurs during each conversion that the ADC
performs is demonstrated in the single channel single-conversion mode:
1. The conversion mode is selected
2. The ADC is turned on
3. The input channel is selected
4. The ADC waits to be enabled or instructed to start conversion
5. When a conversion is triggered, the voltage at the selected input is sampled
Page | 4
6. This voltage is converted to a digital value
7. This value is written to ADC memory register
8. An ADC interrupt is triggered
9. The ADC again waits to be instructed to start a conversion
This process is illustrated below for the single-channel single-conversion mode.
Figure 3. Conversion Process for Single-Channel Single-Conversion Mode
In the other conversion modes, this process only differs in that multiple channels are
automatically samples successively or individual channels are automatically sampled
repeatedly.
Page | 5
7 | ADC Registers
The MSP430 has several control registers that are used to configure various operating
parameters of the peripheral that they correspond to. The registers that are used by the
ADC are listed in the table below.
Figure 4. ADC Registers
The registers that are used to configure the operation of the ADC are the control
registers ADC10CTL0 and ADC10CTL1. The figures below show the contents of these
registers.
Figure 5. ADC10CTL0 Register
Figure 6. ADC10CTL1 Register
Below is a table describing the portions of these control registers that are essential for
basic use of the ADC.
Page | 6
Register Section Description
SREFx Selects high and low reference voltage for ADC
ADC10SHTx Sets ADC sample and hold time
ADC10ON Turns ADC on or off
ADC10IE Enables or disables ADC interrupt
ADC10IFG Interrupt flag set when ADC10MEM is loaded with conversion result
ENC Enables conversion
ADC10SC Starts conversion
INCHx Selects input channel
ADC10DIVx Selects divider for the selected ADC clock
ADC10SSELx Selects source of the clock that will control the ADC
CONSEQx Selects conversion sequence mode
ADC10BUSY Indicates whether the ADC is active
Figure 7. Description of key control register sections
8 | Configuring the ADC
The ADC can be configured with only a few lines of code. Below is an example of a
simple configuration function, written in the C programming language.
1 void ADC_capture(void)
2 {
3 /* Configure ADC Channel */
4 ADC10CTL0 = ADC10SHT_3 + ADC10ON + ADC10IE; //64 clk ticks, ADC on, enable interrupt
5 ADC10CTL1 = ADC10SSEL_0 + INCH_5; //SMCLK, channel 5
6 ADC10CTL0 |= ENC + ADC10SC; //Enable and start conversion
7 while ((ADC10CTL1 & ADC10BUSY) == 0x01); //Wait for conversion to end
8 }
Figure 8. ADC Configuration Code Example
In this example, the control registers are initialized to perform in the way the user
intends to use the ADC. The symbols such as ADC10SHT_3 seen in the code above
stand for individual binary values corresponding to the different configuration options for
each section of the ADC control registers. These options and the corresponding
symbols are defined in the MSP430 User’s Guide, which can be found in a link in the
references section. In this example, the ADC is turned on and channel 5 is selected as
the input channel. The SMCLK is selected as the ADC clock and the ADC interrupt is
enabled. The ADC is instructed to hold its samples for 64 clock ticks before making a
Page | 7
conversion. By default, the ADC is in the single channel single-conversion mode. When
instructed, the ADC begins conversion and the CPU will wait until the ADC10BUSY bit
is cleared before continuing program execution. The ADC triggers an interrupt every
time it performs a conversion, so it is necessary to write an interrupt service routine to
handle the interrupt for the ADC to function properly. Below is an example of an
interrupt service routine to handle the ADC interrupt.
1 // ADC10 interrupt service routine
2 #pragma vector=ADC10_VECTOR
3 __interrupt void ADC10_ISR (void)
4 {
5 __bic_SR_register_on_exit(CPUOFF); // Return to active mode
6 }
Figure 9. ADC Interrupt Service Routine Example
This code can be executed at time intervals defined by a timer peripheral on the
MSP430 to achieve the desired sample rate.
9 | Conclusion
The analog-to-digital converter featured on the MSP430 microcontrollers is a very
powerful tool for developers of applications using this device. It allows users to measure
analog signals such as sensor outputs for instrumentation or control applications. This
application note introduced users to the various operating modes and registers
associated with the ADC and showed how it can be configured with software for the
desired application.
10 | References
[1] MSP430 User’s Guide
http://www.ti.com/product/msp430g2553
[2] MSP430 LaunchPad Wiki
http://processors.wiki.ti.com/index.php/MSP430_LaunchPad_(MSP-EXP430G2)
Page | 8
