Scribd
Upload
2K views2 pages

Amendment No. 1 March 2018 TO Is 4923: 2017 Hollow Steel Sections For Structural Use - Specification

This document outlines amendments made to IS 4923:2017 regarding hollow steel sections for structural use. Key changes include: [1] Replacing symbols used for convexity and corner radius measurements, [2] updating tolerances for thickness, outside dimensions, weight, squareness, and length of sections, [3] removing a reference to straightness measurement, and [4] replacing Annex A with new geometrical data for hollow sections.

Uploaded by

Dhruv and pari showtime
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
2K views2 pages

Amendment No. 1 March 2018 TO Is 4923: 2017 Hollow Steel Sections For Structural Use - Specification

This document outlines amendments made to IS 4923:2017 regarding hollow steel sections for structural use. Key changes include: [1] Replacing symbols used for convexity and corner radius measurements, [2] updating tolerances for thickness, outside dimensions, weight, squareness, and length of sections, [3] removing a reference to straightness measurement, and [4] replacing Annex A with new geometrical data for hollow sections.

Uploaded by

Dhruv and pari showtime
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

AMENDMENT NO.

1 MARCH 2018
TO
IS 4923 : 2017 HOLLOW STEEL SECTIONS FOR STRUCTURAL USE —
SPECIFICATION
(Third Revision)

(Page 1, clause 4, Symbol x1)  Substitute ‘x2 mm Convexity of a side of square or rectangular hollow
section’ for ‘x1 mm Convexity of a side of square or rectangular hollow section’.

(Page 1, clause 4, Symbol r)  Substitute ‘θʼ for ‘rʼ.

Free amendment provided by BIS via BSB Edge Private Limited to NebsShahdra([email protected]) 122.177.44.175
(Page 3, clause 10.5)  Substitute ‘θʼ for ‘rʼ.

(Page 3, clause 10.7, Fig. 5)  Substitute ‘rmaxʼ for ‘rʼ.

[Page 4, section 2, clause 14.1 a), b), c), d) and f)]  Substitute the following for the existing:

a) Thickness of all sizes


1) Welded tubes : ± 7.5 percent
2) Seamless tubes : ± 12.5 percent
b) Outside dimensions of sides : ± 1 percent of length of the side to be measured
with a minimum of ± 0.5 mm
c) Weight
+10
1) On individual length : percent
−8
2) On lots of 10 tonne, Min : ± 7 percent
d) Squareness of corner : 90 ± 2o
f) Length
1) Exact Length : ± 6 mm
2) Random length : This may be obtained by arrangement between
purchaser and manufacture

[Page 5, section 3, clause 18.1 a), b), c), d) and f)]  Substitute the following for the existing:

a) Thickness of all sizes


1) Welded tubes : ± 7.5 percent
2) Seamless tubes : ± 12.5 percent
b) Outside dimensions of sides : ±1 percent of length of the side to be measured
with a minimum of ± 0.5 mm
c) Weight
+10
1) on individual length : percent
−8
2) On lots of 10 tonne, Min : ± 7 percent
d) Squareness of corner : 90 ± 2o
f) Length
1) Exact Length : ± 6 mm
2) Random length : This may be obtained by arrangement between
purchaser and manufacture

[Page 5, clause 18.1 j)]  Delete 5.65 √A given under straightness.

(Page 5, clause 19.2)  Substitute the following for the existing clause:

1
Amendment No. 1 to IS 4923 : 2017

‘19.2 When tested in accordance with IS 1608, the tensile properties of cold formed sections and elongation
percentage on a gauge length of 5.65 √A (where, A is the cross-sectional area of the section) shall be as given in
Table 4.’

[Page 6, Annex A]  Substitute the following for the existing:

ANNEX A
(Clause 8.1)
GEOMETRICAL DATA OF HOLLOW SECTIONS

Free amendment provided by BIS via BSB Edge Private Limited to NebsShahdra([email protected]) 122.177.44.175

(MTD 19)
Publication Unit, BIS, New Delhi, India

You might also like