Scribd
Upload
215 views1 page

Verniciatura: Procedura e Allegati

This document outlines a 3-coat painting cycle for carbon steel. It specifies (1) a zinc phosphate epoxy primer to be applied at 75 μm, (2) a cicloaliphatic amine epoxy intermediate coat at 125 μm, and (3) an acrylic aliphatic polyurethane finish coat at 50 μm, for a total dry film thickness of 250 μm. Inspections will be conducted to check surface preparation, coating thickness, and quality control according to international standards. The cycle is applicable for uninsulated carbon steel with surface temperatures up to 100°C.

Uploaded by

Maffone Numerouno
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
215 views1 page

Verniciatura: Procedura e Allegati

This document outlines a 3-coat painting cycle for carbon steel. It specifies (1) a zinc phosphate epoxy primer to be applied at 75 μm, (2) a cicloaliphatic amine epoxy intermediate coat at 125 μm, and (3) an acrylic aliphatic polyurethane finish coat at 50 μm, for a total dry film thickness of 250 μm. Inspections will be conducted to check surface preparation, coating thickness, and quality control according to international standards. The cycle is applicable for uninsulated carbon steel with surface temperatures up to 100°C.

Uploaded by

Maffone Numerouno
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

Doc. No.

PC 3144
CICLO DI VERNICIATURA
Painting Cycle Sh 1 of 1

PROPRIETA’ TECNICHE VEDI SCHEDE TECNICHE ALLEGATE


Technical Properties See attached technical sheet

PREPARAZIONE SUPERFICIE Cleanliness: Sa 2 ½ according to ISO 8501-1


Surface preparation Profile: 40 µm -50 µm

DESCRIZIONE DEL CICLO


Cycle description

COAT PAINTING TYPE PRODUCT SUPPLIER M.D.F.T. (µm)

Epoxy-polyamide pigmented with


Primer Carboguard E-19 CARBOLINE 75 µm
zinc phospate
Intermediate Cicloaliphatic Amine Epoxy Carboguard 890 MIO CARBOLINE 125 µm

Finish Acrylic aliphatic polyurethane Carbothane 134 HP CARBOLINE 50 µm

TOTAL MINIMUM DRY FILM THICKNESS (µm) 250 µm

White
FINAL COLOUR
BS 4800 00 E5

CONTROLLI RICHIESTI / Inspection requirements


CONTROLLO RUGOSITÀ PREPARAZIONE SUPERFICIALE IN ACCORDO ALLA ISO 8501‐1
Surface Preparation according to ISO 8501‐1
CONTROLLO VISIVO DELLA SUPERFICIE SABBIATA IN ACCORDO ALLA ISO 8502-3
Visual Control of blast cleaned according to ISO 8502-3
CONTROLLO SPESSORE TOTALE IN ACCORDO ALLA SSPC PA 2
Check of total DFT According to SSPC‐PA 2

REMARK
Painting cycle applicable on uninsulated carbon steel material and gear box operator with
surface temperatures 100° C max. according to painting Spec. ZO-TS-Y-02040 System 1

Q.C. Q.C.M Revisionato come da commenti cliente /


1 10.10.2012
S.Frazzi D.Morelli Rrevised as per client comments
Q.C. Q.C.M
0 14.09.2012 Invio per approvazione / Issue for approval
S.Frazzi D.Morelli
Rev: Date: Prepared: Approved: Description:

You might also like