File No.
：NDT2930580 Version：0
Product Specification of NDB6AZ-63H
（IPD-ENG-DEV-T22 A1 2016-09-23）
Product Name: Moulded Case Circuit Breaker
Product type: NDB6AZ-63H
Date: 20190825
Prepared Yang Yanqun Date 2019-8-25
Reviewed Zhang Yang Date 2019-8-26
Approved Yang Hairong Date 2019-8-27
https://www.nader-circuit-breaker.com Page 1 of 6
File No.：NDT2930580 Version：0
Revision information
Version Revised contents and reasons Date Prepared Reviewed Approved
Yang Yang
0 Initial release 20190827 Zhang Yang
Yanqun Hairong
Page 2 of 6
File No.：NDT2930580 Version：0
1、Application
Short -circuit protection
Over-load protection
Isolation
NDB6AZ-63H series products are mainly used in telecommunications equipment rooms or communication
cabinets,as isolation,short circuit and overload protection for cabinets,equipment rooms or downstream
subscriber lines.
2、Product Pictures
NDB6AZ-63H breaker
3、Model and implication
ND B 6A Z - 63 H / 50 B / 1PN
Bre- Design DC Shelf black Rated current Battery:B Number of poles
Low aker number rank 6,10,16,20,25, Load:none N pole straight through
voltage 63A 32,40,50,63
electrical
appliance
Page 3 of 6
File No.：NDT2930580 Version：0
4、Main technical parameters
Specific parameter
Parameter name Specific parameter description Parameter name
description
Model NDB6AZ-63H Rated voltage（V） DC80,AC230/240
Rated limit breaking 10(DC80V),6(6-16A,AC230/240V),
Electrical endurance（times） 4000
capacity(kA) 4.5(20-63A,AC230/240V)
Bare wire：0.75～16
ferrule with plastic sleeve：0.75～10
ferrule without plastic sleeve:16
the schematic diagram of the ferrule’s
cross-sectional area is as follows:
Wiring area（mm2） Mechanical life（times） 6000
cross-sectional area of ferrule:
1.3 mm≤L≤6mm, 1.3 mm≤W≤6mm.
insulation sleeve or heat shrinkable tube diameter
≤9.5mm when ferrul is inserted into 25mm depth.
0.75～6mm²：12～18
Plug depth（mm） 23～25 Stripping length（mm） 10mm²：14～18
16mm²：18±1
Insertion frame force
≤80 Pull out frame force (N) ≤75
(N)
0.75～6mm²：10～16
circuit breaker insertion
200 cold pressed end Length (mm) 10mm²：12～16
and removal times
16mm²：16±1
5、Working conditions
● Height ：≤2000m，provoid derating parameters at more than 2000 meters(derating ratio table see
attachment)
● ambient temperature：-40℃~+70℃
● Can withstand the effects of humid air（Temperature @+40℃ and above，air relative humidity does not
exceed 50%,allows greater relative humidity at lower temperatures,for example,95% @+20℃）
● Can withstand salt spray for 48 hours
● In a medium without explosion hazard,and the medium does not have enough gas and conductive dust to
corrode metal and destroy insulation
Page 4 of 6
File No.：NDT2930580 Version：0
● In places where there is no rain or snow
6、Time-Current curves
● Direct-current
○ Protect conventional and distribution cables
○ Specify ampere rating：6A、10A、16A、20A、25A、32A、40A、50A、63A
○Tripping characteristics：instantaneous trip range 11In(1±20%)
DC Ii=11In（1±20%）
7、Outline and installation dimensions
NDB6AZ-63H Outline and installation dimensions
8、Installation method
Plug-in type, the thickness of the rear-end plug in copper row is 2±0.1mm，signal port copper row thickness
Page 5 of 6
File No.：NDT2930580 Version：0
is 1±0.1mm.
Signal terminal wiring schematic diagram：
9、Packaging and storage
Maximum number of packages:8/box,packed in boxes：24 boxes/box,it should stored in a warehouse where
air circulation and relative humidity is not more than 80%,temperature is not lower than -40℃ but not higer than
80℃.Store in the warehouse without acid,alkaline or other corrosive gases in the surrounding air.
Under the above conditions,the storage period shall not exceed 1 year from the date of manufacture.
10、Environment
Product design meets ROHS requirements.
11、Accessory list and installation
Annex1：derating ratio table of Moulded Case Circuit Breaker with altitude greater than 2000m.
12、Notices
1、Take responsibility for yourself if product quality problems caused by unpacking products privately;
2、Do not touch the exposed part of the non-insulated part of the circuit breaker when the work is energized;
3、Please do not arbitrarily debug the characteristics of the circuit breaker.The manufacturer will not be
responsible for the product quality problems caused by this;
4、The wiring should be reliable to prevent the breaker from circuit breaker malfunction and terminal burned
caused by abnormal heat at the terminals.
Page 6 of 6
