12/30/2010

Electrical Engineering Department

Kota Bharu Polytechnic

Single-Phase Controlled
Rectifiers

Wan Zain Bin Wan Dollah

SINGLE PHASE AC TO DC
CONVERTER
1. HALFWAVE CONTROLLED
RECTIFIER
2. FULLWAVE HALFCONTROLLED
RECTIFIER
3. FULLWAVE FULLY CONTROLLED
RECTIFIER

1
 12/30/2010

The Half-wave Controlled Rectifier

• Normal rectifiers are considered as uncontrolled
rectifiers.
• Once the source and load parameters are
established, the dc level of the output and power
transferred to the load are fixed quantities.

• A way to control the output is to use SCR instead of

diode. Two condition must be met before SCR can
conduct:
– The SCR must be forward biased (VSCR>0)
– Current must be applied to the gate of SCR

• The simplest controlled rectifier uses a single device, such as a

thyristor, to produce variable voltage d.c. from fixed voltage a.c.
mains. The circuit arrangement is shown below

2
 12/30/2010

• The thyristor is turned on in the positive

half-cycle, some time after supply voltage
zero, by the application of a gate pulse
with delay angle α. In the negative half-
cycle, the thyristor is reverse biased and
cannot switch on. The larger the delay
angle, the smaller is the average load
voltage.

Voltage waveforms
for two delay angles are shown below

3
 12/30/2010

Controlled, Half-wave R load

• A gate signal is
applied at t = ,
where is the
delay/firing angle.
Average"DC" outputvoltage
,
1
Vo Vave VDC Vm sin( t) d t Average power absorbed by resistor,
2
V 2 rms
Vms
[1 cos ]
P I 2 rms R
2 R
1
Vo , rms where, Vo , rms [Vm sin( t )]2 d ( t )
Vs 2
I o , rms 0
R 2R Vm sin(2 )
1
2 2

Example
• Design a circuit to produce an average voltage
of 40V across 100 load resistor from a 120Vrms
60 Hz ac source. Determine the power absorbed
by the resistor.

Briefly describe what happen if the circuit is

replaced by diode to produce the same average
output.

4
 12/30/2010

Example (Cont)
• Solution
V 2 rms 75.6 2
In such that to achieved 40V P 57.1W
average voltage, the delay angle R 100
must be
• If an uncontrolled diode is used,
Vms the average voltage would be
Vo [1 cos ]
2
120 2 Vms 2 (120)
40 [1 cos ] Vo 54V
2
61.2o 1.07 rad • That means, some reducing
average resistor to the design must
Vm sin( 2 ) be made. A series resistor or
Vo , rms 1
2 2 inductor could be added to an
120 2 1 .07 sin 2 (1 .07 ) uncontrolled rectifier, while
1 controlled rectifier has advantage
2 2 of not altering the load or
75 .6V introducing the losses

Half - Wave Controlled

Rectifier Circuit with an RL
Load

5
 12/30/2010

Figure 1 : Half-wave controlled

Rectifier with RL Load

When ωt = π, the source

becomes zero, but at this instant,
the current through the circuit is
not zero and there is some
energy stored in the inductor.
When vs becomes negative, the
current through the circuit would
Let vs(t) be Vm sin (ωt). At ωt = not become zero suddenly
0, the current through the because of the inductor. The
circuit is zero. As ωt becomes > inductor acts as a source and
0, vs becomes positive. If a keeps the SCR forward-biased till
diode instead of an SCR has the energy stored in the inductor
been used, the diode would becomes zero. Let the current
start conduction at ωt = 0. With through the circuit become zero
an SCR, the conduction does at ωt = β and the value of β > π.
not start till the SCR is For β < ωt < 2π, the current
triggered. Let the SCR be through the circuit is zero
triggered when ωt = α. Then α
is called the firing angle and
the SCR continues to conduct.

6
 12/30/2010

v ⁄?\‹?h‹ ·¦ ¡?GqkH?k›\

13

v ⁄?h‹ ·¦ ¡?k›\ ?\‹

e‒¡¡•⁄¡¡ ‹£?c › ¡

Average output current, Idc

14

7
 12/30/2010

FULL-WAVE CONTROLLED
CENTER-TAP RECTIFIERS

15

With Resistive Load

Average output voltage, Vdc

Average output current,

8
 12/30/2010

With an Inductive (RL) Load

17

Control Characteristics for center-tap rectifier

18

9
 12/30/2010

With Freewheeling Diode

Average output voltage, Vdc

Average output current,

19

Example 6.4
Explain with the help of waveforms the
operation of a full-wave center-tap
rectifier with RL load for the following
firing angles:
(a) 0°
(b) 45°
(c) 90°
(d) 135°
(e) 180°
20

Assume highly Inductive Load

10
 12/30/2010

Voltage and current waveforms for α =0°

• During positive-half cycle of

source voltage, SCR1 is forward
biased and SCR2 is reverse
biased. During negative half-cycle,
SCR2 is forward biased and SCR1
is reverse biased. In either case
voltage across the load is Vs.

• Output is similar to uncontrolled

rectifier.

• Each SCR conducts for 180° and

supplies current to the load for
this period

21

Voltage and current waveforms for α =45°

• Average DC output voltage

decreases.

• If SCR1 is triggered at 45°,

SCR2 will conduct upto that
point, even though the source
voltage is zero, due to highly
inductive nature of load.

• When SCR1 is turned on, SCR2

is turned off.

• Current to the load is supplied

by SCR1 and SCR2, each
conducting for 180°

22

11
 12/30/2010

Voltage and current waveforms for α =90°

• Average DC voltage is zero, so

there is no transfer of power
from AC source to DC load.

• Each SCR remains in

conduction for 180°

• As firing angle is increased

from 0 to 90°, the power
supplied to the DC load
decreases, becoming zero at
α =90°

23

Voltage and current waveforms for α =135°

• Average DC voltage is
negative.

• Load current still flows in each

SCR for 180° in its original
direction.

• Load voltage has changed

polarity.

• Power now flows from DC load

to AC source .

• Circuit acts like an inverter.

24

12
 12/30/2010

Voltage and current waveforms for α =180°

• Average output DC voltage is at

its maximum negative value.

• SCRs remain in conduction for

180°

25

Example 6.5
Show direction of power flow and
operating mode (rectifying or
inversion) of center-tap rectifier
circuit with following firing angles:

A) α > 0°
B) α < 90°
C) α > 90°
D) α < 180°
26

13
 12/30/2010

Solution

• For firing angle in the range 0° < α < 90°

1. Average output voltage is positive.
2. Converter operates in the rectifying mode.
3. Power to the load is positive
4. Power flow is from AC source to the DC load.

• For firing angle in the range 90° < α < 180°

1. Average output voltage is negative
2. Converter operates in inversion mode
3. Power to the load is negative
4. Power flow is from DC load to AC source

27

Assignment # 2

• In example 6.4, draw waveforms for

voltage across thyristor 2. i.e., VSCR2

28

14
 12/30/2010

FULL-WAVE CONTROLLED
BRIDGE RECTIFIER

29

With Resistive Load

Average output voltage, Vdc

Average output current,

15
 12/30/2010

With an Inductive (RL) Load

Average output voltage, Vdc

Average output current,

31

For L >>> R

32

16
 12/30/2010

Control characteristics for bridge rectifier

33

With RL load and freewheeling

diode

34

17
 12/30/2010

HALF-CONTROLLED
OR
SEMICONTROLLED BRIDGE
RECTIFIERS

35

• In fully-controlled rectifier, only

rectification can be obtained by
connecting a freewheeling diode
across the output terminals of the
rectifier.
• Another method of obtaining
rectification in bridge rectifiers is
replacing half of the SCRs with
diodes. These circuits are called
semicontrolled bridge rectifiers.

36

18
 12/30/2010

Full-wave semicontrolled bridge

rectifier circuit

37

Semicontrolled bridge rectifier with FWD

38

19
 12/30/2010

Dual Converter

39

Exercise Problems
6.1, 6.5, 6.6, 6.9, 6.12, 6.21, 6.22, 6.24
Also give analysis of waveforms in each
case of all above exercise problems

20