GC -Exercice SWMM
1. Example study area
In this tutorial we will model a drainage system for a 1.96 hectare urban catchment. The system
layout is shown in Figure 1. The area will be divided into three sub‐catchments, A1, A2 and A3.
The network consists of storm sewer conduits L01 through L03, and conduit junctions N1, N2
and N3, where flows from sub‐catchments A1, A2 and A3 enter the system . The system
discharges to an open channel at the point labeled Out1. We will first go through the steps of
creating the objects shown in this diagram on SWMM's study area map and setting the various
properties of these objects. Then we will simulate the water quantity (quality not included)
response to a 235 mm, 2‐hour rainfall event.
Figure 1. Example study area.
2. Project Setup
Our first task is to create a new SWMM project and make sure that certain default options are
selected. Using these defaults will simplify the data entry tasks later on.
1. Launch EPA SWMM if it is not already running and select File >> New from the Main
Menu bar to create a new project
2. Select Project >> Defaults to open the Project Defaults dialog.
3. On the ID Labels page of the dialog, set the ID Prefixes as shown in Figure 2. This will make
SWMM automatically label new objects with consecutive numbers following the
designated prefix.
1
Figure 2. Default ID labeling for tutorial example
4. On the Subcatchments page of the dialog set the following default values:
% Slope 2
N‐Imperv. 0.01
N‐Perv. 0.10
Dstore‐Imperv. 0.05
Dstore‐Perv 0.05
%Zero‐Imperv. 25
Infil. Model <click to edit>
‐ Method Curve Number
5. On the Nodes/Links page, set the Flow Units to CMS.
6. Click OK to accept these choices and close the dialog. If you wanted to save these
choices for all future new projects you could check the Save box at the bottom of the
form before accepting it.
Next we will set some map display options so that ID labels and symbols will be displayed as
we add objects to the study area map, and links will have direction arrows.
2
1. Select Tools>> Map Display Options to bring up the Map Options dialog (see Figure 3).
2. Select the Subcatchments page, set the Fill Style to Diagonal and the Symbol Size to 5.
3. Then select the Nodes page and set the Node Size to 5.
4. Select the Annotation page and check on the boxes that will display ID labels for
Subcatchments, Nodes, and Links. Leave the others un‐checked.
5. Finally, select the Flow Arrows page, select the Filled arrow style, and set the arrow
size to 7.
6. Click the OK button to accept these choices and close the dialog.
Figure 3. Map Options dialog.
Before creating the network objects, it is important to select the proper units. This can be done
by selecting proper flow units (
Finally, look in the status bar at the bottom of the main window and check that the Auto‐
Length feature is off and double check that your units are CMS.
3. Drawing Objects
We are now ready to begin adding components to the Study Area Map. We will start with the
subcatchments.
1. Begin by clicking the button on the Object Toolbar. (If the toolbar is not
visible then select View >> Toolbars >> Object). Notice how the mouse cursor changes
shape to a pencil.
2. Move the mouse to the map location where one of the corners of subcatchment A1
lies and left‐click the mouse.
3
3. Do the same for the next three corners and then right‐click the mouse (or hit the
Enter key) to close up the rectangle that represents subcatchment A1. You can press
the Esc key if instead you wanted to cancel your partially drawn subcatchment and
start over again. Don't worry if the shape or position of the object isn't quite right. We
will go back later and show how to fix this.
4. Repeat this process for subcatchments A2 and A3. Observe how sequential ID labels
are generated automatically as we add objects to the map.
Next we will add in the junction nodes and the outfall node that comprise part of the drainage
network.
1. To begin adding junctions, click the
button on the Object Toolbar.
2. Move the mouse to the position of junction N1 and left‐click it. Do the same for
junctions N2 and N4.
3. To add the outfall node, click the button on the Object Toolbar, move the mouse to
the outfall's location on the map, and left‐click. Note how the outfall was automatically
given the name Out1.
At this point your map should look something like that shown in Figure 4.
Figure 4. Subcatchments and nodes for example study area.
Now we will add the storm sewer conduits that connect our drainage system nodes to one
another. We will begin with conduit L01, which connects junction N1 to N2.
1. Click the button on the Object Toolbar. The mouse cursor changes shape to a
crosshair.
2. Click the mouse on junction N1. Note how the mouse cursor changes shape to a pencil.
3. Move the mouse over to junction N2 (note how an outline of the conduit is drawn as
you move the mouse) and left‐click to create the conduit. You could have cancelled
the operation by either right clicking or by hitting the <Esc> key.
4
4. Repeat this procedure for conduits L02 and L03.
Although all of our conduits were drawn as straight lines, it is possible to draw a curved link by
left‐clicking at intermediate points where the direction of the link changes before clicking on
the end node.
To complete the construction of our study area schematic we need to add a rain gage.
1. Click the Rain Gage button on the Object Toolbar.
2. Move the mouse over the Study Area Map to where the gage should be located and
left‐ click the mouse.
At this point we have completed drawing the example study area. Your system should look
like the one in Figure 1. If a rain gage, subcatchment or node is out of position you can move it
by doing the following:
1. If the button is not already depressed, click it to place the map in Object
Selection mode.
2. Click on the object to be moved.
3. Drag the object with the left mouse button held down to its new position.
To re‐shape a subcatchment's outline:
1. With the map in Object Selection mode, click on the subcatchment's centroid
(indicated by a solid square within the subcatchment) to select it.
2. Then click the button on the Map Toolbar to put the map into Vertex Selection
mode.
3. Select a vertex point on the subcatchment outline by clicking on it (note how the
selected vertex is indicated by a filled solid square).
4. Drag the vertex to its new position with the left mouse button held down.
5. If need be, vertices can be added or deleted from the outline by right‐clicking the
mouse and selecting the appropriate option from the popup menu that appears.
6. When finished, click the button to return to Object Selection mode.
This same procedure can also be used to re‐shape a link.
4. Setting Object Properties
As visual objects are added to our project, SWMM assigns them a default set of properties. To
change the value of a specific property for an object we must select the object into the
Property Editor (see Figure 5). There are several different ways to do this. If the Editor is
already visible, then you can simply click on the object or select it from the Data page of the
Browser Panel of the main window. If the Editor is not visible then you can make it appear by
one of the following actions:
• double‐click the object on the map,
• or right‐click on the object and select Properties from the pop‐up menu that appears,
• or select the object from the Data page of the Browser panel and then click the Browser’s
5
button.
Whenever the Property Editor has the focus you can press the F1 key to obtain a more detailed
description of the properties listed.
Two key properties of our subcatchments that need to be set are the rain gage that
supplies rainfall data to the subcatchment and the node of the drainage system that
receives runoff from the subcatchment. Since all of our subcatchments utilize the same rain
gage, Gage1, we can use a shortcut method to set this property for all subcatchments at once:
1. From the main menu select Edit >>Select All.
2. Then select Edit >> Group Edit to make a Group Editor dialog appear (see Figure 6).
3. Select Subcatchment as the type of object to edit, Rain Gage as the property to edit,
and type in Gage1 as the new value.
4. Click OK to change the rain gage of all subcatchments to Gage1. A confirmation dialog
will appear noting that 3 subcatchments have changed. Select “No” when asked to continue
editing.
Figure 5. Property Editor window.
6
Figure 6. Group Editor dialog.
Because the outlet nodes vary by subcatchment, we must set them individually as follows:
1. Double click on subcatchment A1 or select it from the Data Browser and click the
Browser's button to bring up the Property Editor.
2. Type N1 in the Outlet field and press Enter. Note how a dotted line is drawn between the
subcatchment and the node.
3. Click on subcatchment A2 and enter N2 as its Outlet.
4. Click on subcatchment N3 and enter N3 as its Outlet.
Similarly set the area, percent imperviousness and width as shown below.
Name Outlet Area Pcnt. Imperv Width Curve No.
A1 N1 1.0 60 40 81
A2 N2 0.68 75 20 81
A3 N3 0.28 90 20 83
The junctions and outfall of our drainage system need to have invert elevations assigned to
them. As we did with the subcatchments, select each junction individually into the Property
Editor and set its Invert Elevation to the value shown below.
Node Invert El. Depth
N1 18.20 0 1.8
N2 18.00 0 1.8
N3 17.15 9 1.8
Out1 17.000
7
Similarly set the link properties as shown below
Link Shape Max depth Length Outlet offset Manning's Rougness
L01 CIRCULAR 0.2 28.30 0 0.01
L02 CIRCULAR 0.8 20 0.2 0.01
L03 CIRCULAR 1.0 20 0 0.01
In order to provide a source of rainfall input to our project we need to set the rain gage’s
properties. Select Gage1 into the Property Editor and set the following properties:
Rain Format VOLUME
Time Interval 0.15
Data Source TIMESERIES
A time series named Rainfall will contain the 15 minute interval rainfall volumes that make
up our storm. Thus we need to create a time series object and populate it with data. To do
this:
1. From the Data Browser select the Time Series category of objects.
2. Click the button on the Browser to bring up the Time Series Editor dialog (see Figure
7).
3. Enter Rainfall in the Time Series Name field.
4. Enter the values shown in Figure 7 into the Time and Value columns of the data entry
grid (leave the Date column blank).
5. You can click the View button on the dialog to see a graph of the time series values.
Click the OK button to accept the new time series.
8
Figure 7. Time Series Editor dialog.
Having completed the initial design of our example project it is a good idea to give it a title
and save our work to a file at this point. To do this:
1. Select the Title/Notes category from the Data Browser and click the button.
2. In the Project Title/Notes dialog that appears (see Figure 8), enter “Tutorial Example”
as the title of our project and click the OK button to close the dialog.
3. From the File menu select the Save As option.
4. In the Save As dialog that appears, select a folder and file name under which to save this
project. We suggest naming the file [Link]. (An extension of .inp will be added to
the file name if one is not supplied.)
5. Click Save to save the project to file.
The project data are saved to the file in a readable text format. You can view what the file
looks like by selecting Project >> Details from the main menu. To open our project at some
later time, you would select the Open command from the File menu.
9
First Name, Name, 3GC_Class, Date
Figure 8. Title/Notes Editor.
5. Running a Simulation
Setting Simulation Options
Before analyzing the performance of our example drainage system we need to set some
options that determine how the analysis will be carried out. To do this:
1. From the Data Browser, select the Options category and click the button.
2. On the General page of the Simulation Options dialog that appears (see Figure 9),
select Dynamic Wave as the flow routing method..
3. On the Dates page of the dialog, set the End Analysis time to [Link].
4. On the Time Steps page, set the Routing Time Step to 1 second.
5. Set the Reporting time to 5 min and Wet weather and Dry Weather Runoff calculation
intervals each to 1min.
6. Click OK to close the Simulation Options dialog.
10
Figure 9. Simulation Options dialog.
Running a Simulation
We are now ready to run the simulation. To do so, select Project >> Run Simulation (or click
The button). If there was a problem with the simulation, a Status Report will appear
describing what errors occurred.
Viewing the Status Report
The Status Report contains useful summary information about the results of a simulation run.
To view the report select Report >> Status.
• Observe that the continuity errors for surface runoff and conduit routing are small
(typically <1%).
• Of the 235mm of rain that fell on the study area, 15mm infiltrated into the ground
and essentially the remainder became runoff.
• The Node Flooding Summary table indicates there was internal flooding in the system
at node N1.
11
• The Conduit Surcharge Summary table shows that Conduit L01, was surcharged and
therefore appears to be undersized.
Viewing Results on the Map
Simulation results (as well as some design parameters, such as subcatchment area, node invert
elevation, and link maximum depth) can be viewed in color‐coded fashion on the study area
map. To view a particular variable in this fashion:
1. Select the Map page of the Browser panel.
2. Select the variables to view for Subcatchments, Nodes, and Links from the dropdown
combo boxes appearing in the Themes panel. In Figure 11, subcatchment runoff and
link flow have been selected for viewing.
3. The color‐coding used for a particular variable is displayed with a legend on the study
area map. To toggle the display of a legend, select View >> Legends.
4. To move a legend to another location, drag it with the left mouse button held down.
5. To change the color‐coding and the breakpoint values for different colors, select View >>
Legends >> Modify and then the pertinent class of object (or if the legend is already
visible, simply right‐click on it). To view numerical values for the variables being
displayed on the map, select Tools >> Map Display Options and then select the
Annotation page of the Map Options dialog. Use the check boxes for Subcatchment
Values, Node Values, and Link Values to specify what kind of annotation to add.
6. The Date / Time of Day / Elapsed Time controls on the Map Browser can be used to
move through the simulation results in time. Figure 11 depicts results at 1 hours and 30
minutes into the simulation.
7. You can use the controls in the Animator panel of the Map Browser (see Figure 11) to
animate the map display through time. For example, pressing the button will run
the animation forward in time.
12
Figure 11. Example of viewing color‐coded results on the Study Area Map.
Viewing a Time Series Plot
To generate a time series plot of a simulation result:
1. Select Report >> Graph >> Time Series or simply click on the Standard Toolbar.
2. A Time Series Plot dialog will appear. It is used to select the objects and variables to be
plotted.
For our example, the Time Series Plot dialog can be used to graph the flow in conduits L01 and
L02 as follows (refer to Figure 12):
1. Select Links as the Object Category.
2. Select Flow as the Variable to plot.
3. Click on conduit L01 (either on the map or in the Data Browser) and then click
4. Press OK to create the plot, which should look like the graph in Figure 13 in the dialog to
add it to the list of links plotted. Do the same for conduit L02.
13
Figure 12. Time Series Plot dialog.
Figure 13. Time series plot of results from initial simulation run.
14
After a plot is created you can:
• customize its appearance by selecting Report >> Customize or right clicking on the plot,
• copy it to the clipboard and paste it into another application by selecting Edit >>
Copy To or clicking on the Standard Toolbar
• print it by selecting File >> Print or File >> Print Preview (use File >> Page Setup first to
set margins, orientation, etc.).
Viewing a Profile Plot
SWMM can generate profile plots showing how water surface depth varies across a path of
connected nodes and links. Let's create such a plot for the conduits connecting junction N1 to
the outfall Out1 of our example drainage system. To do this:
1. Select Report >> Graph >> Profile or simply click on the Standard Toolbar.
2. Either enter N1 in the Start Node field of the Profile Plot dialog that appears (see Figure
14) or select it on the map or from the Data Browser and click the button next to
the field.
3. Do the same for node Out1 in the End Node field of the dialog.
4. Click the Find Path button. An ordered list of the links forming a connected path
between the specified Start and End nodes will be displayed in the Links in Profile box.
You can edit the entries in this box if need be.
5. Click the OK button to create the plot, showing the water surface profile as it exists at
the simulation time currently selected in the Map Browser (see Figure 15).
Figure 14. Profile Plot dialog.
15
Figure 15. Example of a Profile Plot.
As you move through time using the Map Browser or with the Animator control, the water
depth profile on the plot will be updated.
Optional: Resizing the Network.
1. Go ahead and change the size of the conduit LO1 so that there is no flooding in Node N1 and the
conduit is not surcharged. What is the size of the pipe that fulfills this condition.
2. Due to future land use change it is anticipated that the watershed A1 will become more
impervious in the future. The resulting changes estimated to be
a) Impervious fraction will increase to 85%
b) The curve number will change to 94
Implement these changes in your model and check whether the existing drainage system can
handle the future situation.
16
