BS 5163 Resilient Wedge BS 5163 Flanged Resilient OS&Y Gate Valve,

Type A, (XZ41X), PN10/16,

Gate Valve UL/FM Approved
• Statement:
Gate valves serve to cut the medium flow in the piping system, widely used in the field of potable
water, water supply and drainage, sewage disposal, irrigation, air conditioning, fire protection as
well as chemical and energy industry.

• Features:
1. Material: Ductile Iron EN-GJS-450-10
Body, bonnet, wedge, handwheel and operating nut are all produced in ductile iron material which
provides guarantee for high strength and good corrosion resistance. MATERIAL SPECIFICATION

2. Triple O-ring Stem Seals Part No. Part Standard Specification Options
The lower O-ring isolates the stem thrust collar bearing area from the waterway. The upper two 1 Valve Body EN-GJS-450-10
O-rings can easily be replaced in the line while the valve is under pressure in the open position.
2 Resilient Wedge Disc EN-GJS-450-10+EPDM
3. Stainless Steel Stem, Brass Thrust Collar and Bronze Wedge Nut
3 O-Ring NBR EPDM
This life-tested design has repeatedly proven its superior strength and abrasive
4 Stem SS420 SS304, SS316, SS431, Al-bronze
resistance.
5 Nut Carbon Steel Zinc Plated SS304, SS316
4. Fusion Bonded Epoxy Coating
Fusion bonded epoxy coating in accordance with ANSI/AWWA C550 for both interior and exterior 6 Bonnet EN-GJS-450-10
• Body, Bonnet, Wedge & Operating Nut in 7 Stem Bushing Brass HPb59-1
surface which provides reliable corrosion resistance.
Ductile Iron XZ41X 8 Gland EN-GJS-450-10
5. Long Service Life with Resilient Seat Cycling Test 1,000 times
• Triple O-ring Stem Seals
The Valve has been subjected to 1,000 cycles of operation at a maximum rate of 6 cycles of 9 Flat Washer Carbon Steel Zinc Plated SS304, SS316
• Stainless Steel Stem and Brass Thrust Collar
operation per minute from fully closed to fully open and from fully open to fully closed positions 10 Stud Carbon Steel Zinc Plated SS304, SS316
under cycled hydrostatic pressure. • Bronze Alloy Wedge Nut • Connection Ends: Flange to BS EN 1092-2:1997 11 Nut Carbon Steel Zinc Plated SS304, SS316
• Fusion Bonded Epoxy Coating
• Working Pressure: PN10/16 12 Yoke EN-GJS-450-10
13 Nut Brass HPb59-1
• Temperature Range: 0℃- 80℃
14 Washer Brass HPb59-1
• Coating: Fusion Bonded Epoxy Coating in accordance with
15 Locknut Carbon Steel Zinc Plated
ANSI/AWWA C550
16 Handwheel EN-GJS-450-10 Pressed Steel
17 Stem Packing NBR EPDM
18 Bonnet Gasket EPDM NBR

Note: For special material request other than standard specification, please indicate clearly on the inquiry or order list.

DN Dimensions(mm)
PN
Inch mm L H1(Close) H2(Open) D D1 d C T n-φL
2" 50 10/16 178 323 373 165 125 99 19 3 4-Φ19
XZ41X XZ41XB XZ81X XZ51X Z45XC Z45XBC 2.5" 65 10/16 190 343 408 185 145 118 19 3 4-Φ19
Flanged Resilient OS&Y Flanged Resilient OS&Y Grooved Resilient OS&Y Flanged x Grooved Resilient Flanged Resilient NRS Flanged Resilient NRS
3" 80 10/16 203 370 450 200 160 132 19 3 8-Φ19
Gate Valve, Type A Gate Valve, Type B Gate Valve OS&Y Gate Valve Gate Valve, Type A Gate Valve, Type B
4" 100 10/16 229 442 542 220 180 156 19 3 8-Φ19
Page 11 Page 12 Page 13 Page 14 Page 15 Page 16
5" 125 10/16 254 540 665 250 210 184 19 3 8-Φ19
6" 150 10/16 267 608 758 285 240 211 19 3 8-Φ23
10 8-Φ23
8" 200 292 720 920 340 295 266 20 3
XZ41X-1 16 12-Φ23
10 350 12-Φ23
10" 250 330 940 1190 405 319 22 3
16 355 12-Φ28
10 400 12-Φ23
12" 300 356 1065 1365 460 370 24.5 4
16 410 12-Φ28

Z45XC-2 Z85X Z55X IP WP

Flanged Resilient NRS Grooved Resilient NRS Flanged x Grooved Resilient Vertical Indicator Post Wall Indicator Post
Gate Valve with Post Flange Gate Valve NRS Gate Valve Page 20 Page 21
Page 17 Page 18 Page 19
BS 5163 Flanged Resilient OS&Y BS 5163 Grooved Resilient OS&Y
Gate Valve, Type B (XZ41XB), PN10/16, Gate Valve (XZ81X), PN10/16,
UL/FM Approved UL/FM Approved

MATERIAL SPECIFICATION MATERIAL SPECIFICATION

Part No. Part Standard Specification Options

Part No. Part Standard Specification Options
1 Valve Body EN-GJS-450-10
1 Valve Body EN-GJS-450-10
2 Resilient Wedge Disc EN-GJS-450-10+EPDM
2 Resilient Wedge Disc EN-GJS-450-10+EPDM
3 O-Ring NBR EPDM
3 Stem SS420 SS304, SS316, SS431, Al-bronze
4 Stem SS420 SS304, SS316, SS431, Al-bronze
4 Bonnet Gasket EPDM NBR
5 Nut Carbon Steel Zinc Plated SS304, SS316
5 Bonnet EN-GJS-450-10
6 Bonnet EN-GJS-450-10
6 Washer Brass HPb59-1
XZ41XB XZ81X 7 Stem Bushing Brass Hpb59-1
7 Yoke EN-GJS-450-10
8 Gland EN-GJS-450-10
8 Nut Brass HPb59-1
9 Flat Washer Carbon Steel Zinc Plated SS304, SS316
9 Gland EN-GJS-450-10
10 Stud Carbon Steel Zinc Plated SS304, SS316
• Connection Ends: Flange to BS EN 1092-2:1997 10 Stem Nut Brass HPb59-1 • Connection Ends: Groove to ISO 6182
11 Nut Carbon Steel Zinc Plated SS304, SS316
• Working Pressure: PN10/16 11 Handwheel EN-GJS-450-10 Pressed Steel • Working Pressure: PN10/16
12 Yoke EN-GJS-450-10
12 Washer Brass HPb59-1
• Temperature Range: 0℃- 80℃ • Temperature Range: 0℃- 80℃ 13 Stem Nut Brass Hpb59-1 Bronze ZQSn5-5-5
13 Nut Carbon Steel Zinc Plated SS304, SS316
• Coating: Fusion Bonded Epoxy Coating in accordance with • Coating: Fusion Bonded Epoxy Coating in accordance with 14 Washer Brass Hpb59-1
14 Stud Carbon Steel Zinc Plated SS304, SS316
ANSI/AWWA C550 ANSI/AWWA C550 or painting upon request 15 Locknut Carbon Steel Zinc Plated
15 Flat Washer Carbon Steel Zinc Plated SS304, SS316
16 Handwheel EN-GJS-450-10 Pressed Steel
16 Nut Carbon Steel Zinc Plated SS304, SS316
17 Stem Packing NBR EPDM
17 O-Ring NBR EPDM
18 Bonnet Gasket EPDM NBR
Note: For special material request other than standard specification, please indicate clearly on the inquiry or order list.
Note: For special material request other than standard specification, please indicate clearly on the inquiry or order list.

DN Dimensions(mm)
PN DN Dimensions(mm)
Inch mm L H1(Close) H2(Open) D D1 d C T n-φL
Inch mm L H1(Close) H2(Open) OD d A B
2" 50 10/16 178 348 400 165 125 99 19 3 4-Φ19
2" 50 178 323 373 60.3 57.15 15.88 7.92
2.5" 65 10/16 190 373 440 185 145 118 19 3 4-Φ19
2.5" 65 190 343 408 73 69.09 15.88 7.92
3" 80 10/16 203 408 490 200 160 132 19 3 8-Φ19
2.5" 65 190 343 408 76.1 72.26 15.88 7.92
4" 100 10/16 229 471 573 220 180 156 19 3 8-Φ19
3" 80 203 370 450 88.9 84.94 15.88 7.92
5" 125 10/16 254 541 665 250 210 184 19 3 8-Φ19
4" 100 229 442 542 114.3 110.08 15.88 9.52
6" 150 10/16 267 593 743 285 240 211 19 3 8-Φ23
5" 125 254 541 665 139.7 135.48 15.88 9.52
10 8-Φ23
8" 200 292 774 975 340 295 266 20 3 5" 125 254 541 665 141.3 137.03 15.88 9.52
16 12-Φ23
XZ41XB-1 6" 150 267 608 758 165.1 160.90 15.88 9.52
10 350 12-Φ23
10" 250 330 1029 1283 405 319 22 3 6" 150 267 608 758 168.3 163.96 15.88 9.52
16 355 12-Φ28
8" 200 292 697 897 219.1 214.40 19.05 11.13
10 400 12-Φ23
12" 300 356 1065 1370 460 370 24.5 4 10" 250 330 939 1193 273.0 268.28 19.05 12.70
16 410 12-Φ28
12" 300 356 1065 1370 323.9 318.29 19.05 12.70
BS 5163 Flanged x Grooved Resilient OS&Y BS 5163 Flanged Resilient NRS
Gate Valve (XZ51X), PN10/16, Gate Valve, Type A (Z45XC), PN10/16,
UL/FM Approved UL/FM Approved

MATERIAL SPECIFICATION MATERIAL SPECIFICATION

Part No. Part Standard Specification Options Part No. Part Standard Specification Options
1 Valve Body EN-GJS-450-10 　 1 Valve Body EN-GJS-450-10
2 Resilient Wedge Disc EN-GJS-450-10+EPDM 　 2 Resilient Wedge Disc EN-GJS-450-10+EPDM
3 O-Ring NBR EPDM 3 Stem SS420 SS304, SS316, SS431, Al-bronze
4 Stem SS420 SS304, SS316, SS431, Al-bronze 4 Nut Carbon Steel Zinc Plated SS304, SS316

XZ51X 5 Bolt Carbon Steel Zinc Plated SS304, SS316 Z45XC 5 Bonnet EN-GJS-450-10
6 Bonnet EN-GJS-450-10 　 6 O-Ring NBR EPDM

7 Stem Bushing Brass HPb59-1 　 7 Gland EN-GJS-450-10

8 Gland EN-GJS-450-10 　 8 Stem Cap EN-GJS-450-10

• Connection Ends: Flange to EN 1092-2:1997, • Connection Ends: Flange to BS EN 1092-2:1997
9 Flat Washer Carbon Steel Zinc Plated SS304, SS316 9 Bolt Carbon Steel Zinc Plated SS304, SS316
Groove to ISO 6182 • Working Pressure: PN10/16
10 Stud Carbon Steel Zinc Plated SS304, SS316 10 Ring Wiper EPDM NBR
• Working Pressure: PN10/16 • Temperature Range: 0℃- 80℃ 11 Bolt Carbon Steel Zinc Plated SS304, SS316
11 Nut Carbon Steel Zinc Plated SS304, SS316
• Temperature Range: 0℃- 80℃ 12 Yoke EN-GJS-450-10 　 • Coating: Fusion Bonded Epoxy Coating in accordance with 12 Flat Washer Carbon Steel Zinc Plated SS304, SS316

• Coating: Fusion Bonded Epoxy Coating in accordance with 13 Nut Brass HPb59-1 　 ANSI/AWWA C550 13 O-Ring NBR EPDM
ANSI/AWWA C550 14 Washer Brass HPb59-1 　
14 Thrust Washer Brass Hpb59-1
15 Bonnet Gasket EPDM NBR
15 Locknut Carbon Steel Zinc Plated 　
16 Wedge Nut Brass Hpb59-1 Bronze ZQSn5-5-5
16 Handwheel EN-GJS-450-10 Pressed Steel
17 Stem Packing NBR EPDM Note: For special material request other than standard specification, please indicate clearly on the inquiry or order list.
18 Bonnet Gasket EPDM NBR

Note: For special material request other than standard specification, please indicate clearly on the inquiry or order list.
DN Dimensions(mm)
PN
Inch mm L H D D1 d C T n-d
2" 50 10/16 178 278 165 125 99 19 3 4-Φ19
DN Dimensions(mm) 2.5" 65 10/16 190 292 185 145 118 19 3 4-Φ19
Inch mm L H1(Close) H2(Open) D D1 n-d OD d A B 3" 80 10/16 203 351 200 160 132 19 3 8-Φ19
Z45X Z45X-1
2" 50 178 323 373 165 125 4-Φ19 60.3 57.15 15.88 7.92 4" 100 10/16 229 384 220 180 156 19 3 8-Φ19
2.5" 65 190 343 408 185 145 4-Φ19 76.1 72.26 15.88 7.92 5" 125 10/16 254 461 250 210 184 19 3 8-Φ19
3" 80 203 370 450 200 160 8-Φ19 88.9 84.94 15.88 7.92 6" 150 10/16 267 483 285 240 211 19 3 8-Φ23
4" 100 229 442 542 220 180 8-Φ19 114.3 110.08 15.88 9.52 10 8-Φ23
8" 200 553 490 340 295 266 20 3
5" 125 254 541 665 250 210 8-Φ19 139.7 135.48 15.88 9.52 16 12-Φ23
6" 150 267 608 758 285 240 8-Φ23 165.1 160.90 15.88 9.52 10 350 12-Φ23
10" 250 705 626 405 319 22 3
6" 150 267 608 758 285 240 8-Φ23 168.3 163.96 15.88 9.52 16 355 12-Φ28
8" 200 292 697 897 340 295 12-Φ23 219.1 214.40 19.05 11.13 10 400 12-Φ23
12" 300 801 722 460 370 24.5 4
10" 250 330 939 1193 405 355 12-Φ28 273.0 268.28 19.05 12.70 16 410 12-Φ28
12" 300 356 1065 1370 460 410 12-Φ28 323.9 318.29 19.05 12.70

XZ45X-1 XZ45X XZ45X-2

BS 5163 Flanged Resilient NRS BS 5163 Flanged Resilient NRS
Gate Valve, Type B (Z45XBC), PN10/16, Gate Valve,with Post Flange (Z45XC-2),
UL/FM Approved PN10/16, UL Listed

MATERIAL SPECIFICATION MATERIAL SPECIFICATION

Part No. Part Standard Specification Options Part No. Part Standard Specification Options

1 Valve Body EN-GJS-450-10 1 Valve Body EN-GJS-450-10

2 Resilient Wedge Disc EN-GJS-450-10+EPDM 2 Resilient Wedge Disc EN-GJS-450-10+EPDM

3 Stem SS431 SS304, SS316, Al-bronze 3 Stem SS420 SS304, SS316, SS431, Al-bronze

4 Bonnet Gasket EPDM NBR 4 Nut Carbon Steel Zinc Plated SS304, SS316

5 Bonnet EN-GJS-450-10 5 Bonnet EN-GJS-450-10

6 O-Ring NBR EPDM 6 O-Ring NBR EPDM

7 Gland EN-GJS-450-10 7 Gland EN-GJS-450-10

Z45XBC 8 Stem Cap EN-GJS-450-10
Z45XC-2 8 Stem Cap EN-GJS-450-10

9 Nut Carbon Steel Zinc Plated SS304, SS316 9 Bolt Carbon Steel Zinc Plated SS304, SS316

10 Ring Wiper EPDM NBR 10 Ring Wiper EPDM NBR

• Connection Ends: Flange to BS EN 1092-2:1997 11 O-Ring NBR EPDM
• Connection Ends: Flange to BS EN 1092-2:1997 11 Bolt Carbon Steel Zinc Plated SS304, SS316

• Working Pressure: PN10/16 12 Nut Carbon Steel Zinc Plated SS304, SS316 • Working Pressure: PN10/16 12 Flat Washer Carbon Steel Zinc Plated SS304, SS316

13 Axis Guide Brass HPb59-1 13 O-Ring NBR EPDM

• Temperature Range: 0℃- 80℃ • Temperature Range: 0℃- 80℃
14 Washer Brass Hpb59-1 14 Thrust Washer Brass Hpb59-1
• Coating: Fusion Bonded Epoxy Coating in accordance with • Coating: Fusion Bonded Epoxy Coating in accordance with
15 O-Ring NBR 15 Bonnet Gasket EPDM NBR
ANSI/AWWA C550 ANSI/AWWA C550
16 Nut Carbon Steel Zinc Plated SS304, SS316 16 Wedge Nut Brass Hpb59-1 Bronze ZQSn5-5-5

17 Wedge nut Brass Hpb59-1 Bronze ZQSn5-5-5 17 Post Flange EN-GJS-450-10

Note: For special material request other than standard specification, please indicate clearly on the inquiry or order list. Note: For special material request other than standard specification, please indicate clearly on the inquiry or order list.

DN Dimensions(mm) DN Dimensions(mm)
PN PN
Inch mm L H D D1 d C T n-φL Inch mm L H D D1 d C T n-d
2" 50 10/16 178 332 165 125 99 19 3 4-Φ19 4" 100 10/16 229 409 220 180 156 19 3 8-Φ19
2.5" 65 10/16 190 350 185 145 118 19 3 4-Φ19 5" 125 10/16 254 486 250 210 184 19 3 8-Φ19
3" 80 10/16 203 376 200 160 132 19 3 8-Φ19 6" 150 10/16 267 508 285 240 211 19 3 8-Φ23
4" 100 10/16 229 429 220 180 156 19 3 8-Φ19 10 8-Φ23
8" 200 292 578 340 295 266 20 3
Z45XB Z45XB-1 5" 125 10/16 254 461 250 210 184 19 3 8-Φ19 16 12-Φ23
6" 150 10/16 267 520 285 240 211 19 3 8-Φ23 10 350 12-Φ23
10" 250 330 730 405 319 22 3
10 8-Φ23 16 355 12-Φ28
8" 200 292 622 340 295 266 20 3
16 12-Φ23 10 400 12-Φ23
12" 300 356 826 460 370 24.5 4
10 350 12-Φ23 16 410 12-Φ28
10" 250 330 691 405 319 22 3
16 355 12-Φ28
10 400 12-Φ23
12" 300 356 793 460 370 24.5 4
16 410 12-Φ28

XZ45XB-1 XZ45XB XZ45XB-2

BS 5163 Grooved Resilient NRS BS 5163 Flanged x Grooved Resilient NRS
Gate Valve (Z85X), PN10/16, Gate Valve (Z55X), PN10/16,
UL/FM Approved UL/FM Approved

MATERIAL SPECIFICATION MATERIAL SPECIFICATION

Part No. Part Standard Specification Options Part No. Part Standard Specification Options

1 Valve Body EN-GJS-450-10 1 Valve Body EN-GJS-450-10 　

2 Resilient Wedge Disc EN-GJS-450-10+EPDM 2 Resilient Wedge Disc EN-GJS-450-10+EPDM 　
3 Stem SS420 SS304, SS316, SS431, Al-bronze 3 Stem SS420 SS304, SS316, SS431, Al-bronze
4 Nut Carbon Steel Zinc Plated SS304, SS316 4 Bolt Carbon Steel Zinc Plated SS304, SS316
5 Bonnet EN-GJS-450-10 5 Bonnet EN-GJS-450-10 　
Z85X Z55X
6 O-Ring NBR EPDM 6 O-Ring NBR EPDM
7 Gland EN-GJS-450-10 7 Gland EN-GJS-450-10 　
8 Handwheel EN-GJS-450-10 Pressed Steel 8 Handwheel EN-GJS-450-10 Pressed Steel
• Connection Ends: Groove to ISO 6182 9 Bolt Carbon Steel Zinc Plated SS304, SS316 • Connection Ends: Flange to EN 1092-2:1997, 9 Bolt Carbon Steel Zinc Plated SS304, SS316
10 Flat Washer Carbon Steel Zinc Plated SS304, SS316 Groove to ISO 6182
• Working Pressure: PN10/16 10 Flat Washer Carbon Steel Zinc Plated SS304, SS316
11 Ring Wiper EPDM NBR • Working Pressure: PN10/16 11 Ring Wiper EPDM NBR
• Temperature Range: 0℃- 80℃
12 Bolt Carbon Steel Zinc Plated SS304, SS316
• Temperature Range: 0℃- 80℃ 12 Bolt Carbon Steel Zinc Plated SS304, SS316
• Coating: Fusion Bonded Epoxy Coating in accordance with 13 Flat Washer Carbon Steel Zinc Plated SS304, SS316 13 Flat Washer Carbon Steel Zinc Plated SS304, SS316
ANSI/AWWA C550 or painting upon request • Coating: Fusion Bonded Epoxy Coating in accordance with
14 O-Ring NBR EMDM
ANSI/AWWA C550 14 O-Ring NBR EPDM
15 Washer Brass HPb59-1
15 Washer Brass HPb59-1
16 Bonnet Gasket EPDM NBR
16 Bonnet Gasket EPDM NBR
17 Wedge Nut Brass HPb59-1 Bronze ZQSn5-5-5
17 Wedge Nut Brass HPb59-1 Bronze ZQSn5-5-5
Note: For special material request other than standard specification, please indicate clearly on the inquiry or order list.
Note: For special material request other than standard specification, please indicate clearly on the inquiry or order list.

DN Dimensions(mm) DN Dimensions(mm)
Inch mm L H OD d A B Inch mm L H D D1 n-d OD d A B
2" 50 178 218 60.3 57.15 15.88 7.92 2" 50 178 218 165 125 4-Φ19 60.3 57.15 15.88 7.92
2.5" 65 190 230 73 69.09 15.88 7.92 2.5" 65 190 230 185 145 4-Φ19 76.1 72.26 15.88 7.92
2.5" 65 190 230 76.1 72.26 15.88 7.92 3" 80 203 281 200 160 8-Φ19 88.9 84.94 15.88 7.92
3" 80 203 281 88.9 84.94 15.88 7.92 4" 100 229 316 220 180 8-Φ19 114.3 110.08 15.88 9.52
4" 100 229 316 114.3 110.08 15.88 9.52 5" 125 254 393 250 210 8-Φ19 139.7 135.48 15.88 9.52
5" 125 254 393 139.7 135.48 15.88 9.52 6" 150 267 420 285 240 8-Φ23 165.1 160.90 15.88 9.52
5" 125 254 393 141.3 137.03 15.88 9.52 6" 150 267 420 285 240 8-Φ23 168.3 163.96 15.88 9.52
6" 150 267 420 165.1 160.90 15.88 9.52 8" 200 292 490 340 295 12-Φ23 219.1 214.40 19.05 11.13
6" 150 267 420 168.3 163.96 15.88 9.52 10" 250 330 626 405 355 12-Φ28 273.0 268.28 19.05 12.70
8" 200 292 490 219.1 214.40 19.05 11.13 12" 300 356 722 460 410 12-Φ28 323.9 318.29 19.05 12.70
10" 250 330 626 273.0 268.28 19.05 12.70
12" 300 356 722 323.9 318.29 19.05 12.70
Vertical Indicator Post (IP), Wall Indicator Post (WP),
UL Listed UL Listed

MATERIAL SPECIFICATION

Part No. Part Standard Specification

1 Hex Nut Carbon Steel Zinc Plated
2 Hex Bolt Carbon Steel Zinc Plated
3 Socket EN-GJS-450-10
4 Cotter Pin SS304
5 Base Flange Cast Iron EN-GJL-200
6 Hex Bolt Carbon Steel Zinc Plated
7 Hex Nut Carbon Steel Zinc Plated
8 Standpipe Carbon Steel
9 Stem 1" Square Carbon Steel
10 Body Cast Iron EN-GJL-200
11 Locking Wrench EN-GJS-450-10
12 Target Carrier Nut Cast Aluminum
MATERIAL SPECIFICATION
13 Hex Bolt Carbon Steel Zinc Plated
Part No. Part Standard Specification
14 Hex Nut Carbon Steel Zinc Plated
1 Body Cast Iron EN-GJL-200
15 Hex Bolt Carbon Steel Zinc Plated WP
2 Plug Malleable Iron
16 Target Cast Aluminum
3 Square Nut Carbon Steel Zinc Plated
17 Window Glass Plexiglass
4 Hex Bolt Carbon Steel Zinc Plated
18 Gasket PTFE
• Statement: 5 Cover Cast Iron EN-GJL-200
19 Operating Nut SS304
Wall indicator post provides a means to operate a valve installed 6 Hand Wheel EN-GJS-450-10
20 Top Section Cast Iron EN-GJL-200
behind a wall and able to indicate the open or shut position of the 7 Eye Bolt Carbon Steel Zinc Plated
21 Snap Ring Spring Steel
valve.
8 Gasket Carbon Steel Zinc Plated
22 Plug Malleable Iron
IP • Coating: 9 Snap Ring Spring Steel
23 Square Nut Carbon Steel Zinc Plated
Fusion Bonded Epoxy Coating in accordance with 10 Operating Nut SS304
24 Hex Bolt Carbon Steel Zinc Plated
ANSI/AWWA C550
11 Gasket PTFE
Field Adjustment:
• Statement: 12 Window Class Plexiglass
1.Remove the Top Section from the top of the Indicator Post assembly;
Vertical indicator post provides a means to operate a 2.Cut the required stem length and adjust the Standpipe to match up to the ground line; 13 Target Cast Aluminum
buried or otherwise inaccessible valve and able to indicate 3.Set the "OPEN" and "SHUT" targets for the appropriate valve size; 14 Hex Bolt Carbon Steel Zinc Plated
the open or shut position of the valve. 4.Reattach the Top Section to the top of the Indicator Post assembly.
15 Hex Bolt Carbon Steel Zinc Plated
• Coating: 16 Hex Nut Carbon Steel Zinc Plated
Fusion Bonded Epoxy Coating in accordance with 17 Target Carrier Nut SS304
ANSI/AWWA C550
18 Hex Nut Carbon Steel Zinc Plated
19 Hex Bolt Carbon Steel Zinc Plated
20 Stem 1" Square Carbon Steel
21 Cotter Pin SS304
22 Socket ASTM A536, 65-45-12

Note: For special material request other than standard specification, please indicate clearly on the inquiry or order list;
BS EN 593 Resilient Centerline BS EN 593 Grooved Butterfly Valve
with Tamper Switch (XD381X4),
Butterfly Valve PN10/16

• Statement:
Resilient centerline butterfly valves usually serve to cut off medium flow in the piping system,
widely applied in the field of potable water, water supply and drainage, sewage disposal, irrigation,
air conditioning, fire protection as well as chemical and energy industry. The design of the butterfly
valves, however, makes it also suitable to serve as adjusting valve.
• Features:
1. Material:
Body is produced in ductile iron material (EN-GJS-450-10) which provides guarantee for high
strength and good corrosion resistance.
Different options of the disc and seat, e.g. disc of DI nickel or nylon 11 coated, different series of
MATERIAL SPECIFICATION
stainless steel, Al-bronze, seat in EPDM, NBR or Fluororubber, makes it suitable to be applied
under different working conditions. Part No. Part Standard Specification Options
1 Valve Body EN-GJS-450-10
2. Design:
Universal flange connection to BS EN 1092 PN6/10/16, ASME B16.1 CL 125, ASME B16.5 CL150, 2 Disc EN-GJS-450-10+EPDM EN-GJS-450-10+NBR
GB9113, JIS B2112 10K, AS 2129 Table E, BS 10 Table D/E. 3 O-Ring NBR EPDM
XD381X4
Different options of operation including lever handle, gear box, gear box with tamper switch, 4 Stem SS431 SS304, SS316, SS416, SS420
electric drive, and pneumatic drive, etc. • Ductile Iron Valve Body • Design Standard: BS EN 593 5 O-Ring NBR EPDM
Different options of rubber seat including insert rubber seat, rubber vulcanized on valve body and
• Stainless Steel Stem • Connection Ends: Groove to ISO 6182 6 Stem SS431 SS304, SS316, SS416, SS420
boot rubber seat.
• Fusion Bonded Epoxy Coating 7 Signal Gear Box EN-GJS-450-10
3. Coating • Top Flange standard: ISO 5211
Fusion bonded epoxy coating provides reliable corrosion resistance. • Disc: DI, Stainless Steel or Al-bronze Stem drive by keys, parallel or diagonal square or flat head Note: For special material request other than standard specification, please indicate clearly on the inquiry or order list.
To achieve higher corrosion resistance, factory is also able to supply Nylon 11 coated disc. Nylon • Seat: EPDM/NBR/Fluororubber with backing • Working Pressure: PN10/16
11 coating is thermoplastic plant coating approved by USDA with high corrosion resistance and
• Temperature Range: 0℃- 80℃ SWITCH WIRING DIAGRAM
antisepsis which can be applied where there is strict requirement for anti-corrosion.
• Coating: Fusion Bonded Epoxy Coating in accordance with Open (Red)
ANSI/AWWA C550 or painting upon request Common (White) Closed (Black)
Fire Alarm Control End of Line Resistor
Panel Supervisory Circuit or Next Device

Actuator Case Ground (Yellow/Green Double Color)

XD381X4 D81X4 D81X4-BL XD371X4

Grooved Butterfly Valve Grooved Butterfly Valve Grooved Butterfly Valve Wafer Butterfly Valve Open (Yellow)
with Tamper Switch Page 24 Page 25 with Tamper Switch
Common (Green) Closed (Blue) Aux. Device
Page 23 Page 26 Voltage Source
(Bell or Horn)

Two-Piece Stem Pinless Butterfly Valves Kv Value

DN
10° 20° 30° 40° 50° 60° 70° 80° 90° DN Dimensions(mm)
Inch mm
2" 50 0.17 4 8 15 23 46 61 99 125 Inch mm A B C ΦD ΦF ΦG L1 L2 L ΦK H H1 H2 H3 J ΦM Φ2 ISO 5211
2.5" 65 0.35 7 13 22 36 72 91 151 195 2" 50 89 65 81 50.3 60.3 57.15 15.88 7.93 32 90 208 151 65 108 147 150 14 F07
3" 80 0.52 10 19 33 54 108 138 225 281
2.5" 65 102 71 97 60.8 73.0 69.09 15.88 7.93 32 90 208 151 65 108 147 150 14 F07
4" 100 0.69 15 36 63 104 203 264 441 510
5" 125 1.70 39 76 134 216 424 541 865 973 2.5" 65 102 71 97 60.8 76.1 72.26 15.88 7.93 32 90 208 151 65 108 147 150 14 F07
6" 150 2.60 77 125 216 355 692 891 1427 1687 3" 80 109 81 97 76 88.9 84.94 15.88 7.93 32 90 208 151 65 108 147 150 14 F07
8" 200 3.50 128 216 363 606 1125 1514 2357 2811
4" 100 128 95 116 98.5 114.3 110.08 15.88 9.53 32 90 208 151 65 108 147 150 16 F07
10" 250 4.30 201 337 580 995 1860 2379 3720 4325
12" 300 5.20 296 476 865 1384 2682 3503 4325 6488 5" 125 141 111 148 122.6 139.7 135.48 15.88 9.53 32 90 208 151 65 108 147 150 16 F07
5" 125 141 111 148 122.6 141.3 137.03 15.88 9.53 32 90 208 151 65 108 147 150 16 F07

One-Piece Stem Pinless Butterfly Valves Kv Value 6" 150 153 133 148 148 165.1 160.9 15.88 9.53 32 90 208 151 65 108 147 150 20 F07

DN 6" 150 153 133 148 148 168.3 163.96 15.88 9.53 32 90 208 151 65 108 147 150 20 F07
10° 20° 30° 40° 50° 60° 70° 80° 90°
Inch mm 8" 200 184 164 133 199 219.1 214.4 19.05 11.10 45 125 303 239 73 115 190 250 26 F10
2" 50 0.05 3 6 13 23 38 61 91 99 10" 250 216 196 159 252 273.1 268.28 19.05 12.70 45 125 303 239 73 115 190 250 26 F10
2.5" 65 0.09 5 10 22 39 65 103 154 170
3" 80 0.17 8 16 34 61 100 158 238 261 12" 300 254 226 165 300.5 323.9 318.29 19.05 12.70 45 125 303 229 73 120 190 250 28 F10
4" 100 0.26 15 31 67 120 199 315 472 519
Note: Valve must not be installed with disc in full open position. Disc must be partly closed so that no part is protruding beyond end of valve body.
5" 125 0.43 25 53 115 205 339 536 804 884
6" 150 0.69 29 82 132 222 365 611 998 1366
8" 200 2 48 133 217 365 599 1002 1637 1873
10" 250 3 75 206 333 566 928 1552 2535 2901
12" 300 3 132 361 589 990 1625 2718 4439 5041
BS EN 593 Grooved Butterfly Valve BS EN 593 Grooved Butterfly Valve
(D81X4, D381X4), (D81X4-BL, D381X4-BL),
PN10/16 PN10/16

MATERIAL SPECIFICATION MATERIAL SPECIFICATION

Part No. Part Standard Specification Options Part No. Part Standard Specification Options
1 Valve Body EN-GJS-450-10 1 Valve Body EN-GJS-450-10

D81X4 2 Disc EN-GJS-450-10+EPDM EN-GJS-450-10+NBR

D81X4-BL 2 Disc EN-GJS-450-10+EPDM EN-GJS-450-10+NBR
3 O-Ring NBR EPDM 3 O-Ring NBR EPDM
• Design Standard: BS EN 593 4 Stem SS431 SS304, SS316, SS416, SS420 • Design Standard: BS EN 593 4 Stem SS431 SS304, SS316, SS416, SS420

• Connection Ends: Groove to ISO 6182 5 O-Ring NBR EPDM • Connection Ends: Groove to ISO 6182 5 O-Ring NBR EPDM
6 Stem SS431 SS304, SS316, SS416, SS420 6 Stem SS431 SS304, SS316, SS416, SS420
• Top Flange standard: ISO 5211 • Top Flange standard: ISO 5211
7 Lever EN-GJS-450-10 Aluminum 7 Lever EN-GJS-450-10 Aluminum
Stem drive by keys, parallel or diagonal square or flat head Stem drive by keys, parallel or diagonal square or flat head
8 Gear Box EN-GJS-450-10 8 Gear Box EN-GJS-450-10
• Working Pressure: PN10/16 • Working Pressure: PN10/16
Note: For special material request other than standard specification, please indicate clearly on the inquiry or order list. Note: For special material request other than standard specification, please indicate clearly on the inquiry or order list.
• Temperature Range: 0℃- 80℃ • Temperature Range: 0℃- 80℃
• Coating: Fusion Bonded Epoxy Coating in accordance with • Coating: Fusion Bonded Epoxy Coating in accordance with
ANSI/AWWA C550 or painting upon request ANSI/AWWA C550 or painting upon request

D381X4 D381X4-BL

DN Dimensions(mm) DN Dimensions(mm)
Inch mm A B C ΦD ΦF ΦG L1 L2 L ΦK H H1 H2 J ΦM Φ2 ISO 5211 ΦE N-Φ1 Inch mm A B C ΦD ΦF ΦG L1 L2 L ΦK H H1 H2 J ΦM SXS ISO 5211 ΦE N-Φ1
2" 50 89 65 81 50.3 60.3 57.15 15.88 7.93 32 90 206 158 52 114 150 14 F07 70 4-Φ10 2" 50 100 65 81 50.3 60.3 57.15 15.88 7.93 32 90 206 158 52 114 150 11X11 F07 70 4-Φ10
2.5" 65 102 71 97 60.8 73.0 69.09 15.88 7.93 32 90 206 158 52 114 150 14 F07 70 4-Φ10 2.5" 65 115 71 97 60.8 73.0 69.09 15.88 7.93 32 90 206 158 52 114 150 11X11 F07 70 4-Φ10
2.5" 65 102 71 97 60.8 76.1 72.26 15.88 7.93 32 90 206 158 52 114 150 14 F07 70 4-Φ10 2.5" 65 115 71 97 60.8 76.1 72.26 15.88 7.93 32 90 206 158 52 114 150 11X11 F07 70 4-Φ10
3" 80 109 81 97 76 88.9 84.94 15.88 7.93 32 90 206 158 52 114 150 14 F07 70 4-Φ10 3" 80 113 81 97 76 88.9 84.94 15.88 7.93 32 90 206 158 52 114 150 11X11 F07 70 4-Φ10
4" 100 128 95 116 98.5 114.3 110.08 15.88 9.53 32 90 206 158 52 114 150 16 F07 70 4-Φ10 4" 100 145 95 116 98.5 114.3 110.08 15.88 9.53 32 90 206 158 52 114 150 14X14 F07 70 4-Φ10
5" 125 141 111 148 122.6 139.7 135.48 15.88 9.53 32 90 206 158 52 114 150 16 F07 70 4-Φ10 5" 125 141 111 148 122.6 139.7 135.48 15.88 9.53 32 90 206 158 52 114 150 14X14 F07 70 4-Φ10
5" 125 141 111 148 122.6 141.3 137.03 15.88 9.53 32 90 206 158 52 114 150 16 F07 70 4-Φ10 5" 125 141 111 148 122.6 141.3 137.03 15.88 9.53 32 90 206 158 52 114 150 14X14 F07 70 4-Φ10
6" 150 153 133 148 148 165.1 160.9 15.88 9.53 32 90 206 158 52 114 150 20 F07 70 4-Φ10 6" 150 177 133 148 148 165.1 160.9 15.88 9.53 32 90 206 158 52 114 150 17X17 F07 70 4-Φ10
6" 150 153 133 148 148 168.3 163.96 15.88 9.53 32 90 206 158 52 114 150 20 F07 70 4-Φ10 6" 150 177 133 148 148 168.3 163.96 15.88 9.53 32 90 206 158 52 114 150 17X17 F07 70 4-Φ10
8" 200 184 164 133 199 219.1 214.4 19.05 11.10 45 125 310 239 69 167 300 26 F10 102 4-Φ12 8" 200 200 164 133 199 219.1 214.4 19.05 11.10 45 125 310 239 69 167 300 17X17 F10 102 4-Φ12
10" 250 216 196 159 252 273.1 268.28 19.05 12.70 45 125 310 239 69 167 300 26 F10 102 4-Φ12 10" 250 280 196 159 252 273.1 268.28 19.05 12.70 45 125 310 239 69 167 300 22X22 F10 102 4-Φ12
12" 300 254 226 165 300.5 323.9 318.29 19.05 12.70 45 125 307 229 73 190 300 28 F10 102 4-Φ12 12" 300 300 226 165 300.5 323.9 318.29 19.05 12.70 45 125 307 229 73 190 300 22X22 F10 102 4-Φ12

Note: Valve must not be installed with disc in full open position. Disc must be partly closed so that no part is protruding beyond end of valve body. Note: Valve must not be installed with disc in full open position. Disc must be partly closed so that no part is protruding beyond end of valve body.
BS EN 593 Wafer Butterfly Valve
with Tamper Switch (XD371X4),
BS Standard Check Valve
PN10/16
• Statement:
Check valves serve to prevent the backflow of medium in the piping system for protection
of important equipments, widely used in the field of potable water, water supply and
drainage, sewage disposal, irrigation, air conditioning, fire protection as well as chemical
and energy industry.

• Features:
1. Material: Ductile Iron EN-GJS-450-10
Valve body, bonnet, disc are all produced in ductile iron material which provides
MATERIAL SPECIFICATION guarantee for high strength and good corrosion resistance.
Part No. Part Standard Specification Options
2. Fusion bonded epoxy coating
Fusion bonded epoxy coating in accordance with ANSI/AWWA C550 for both interior and
1 Valve Body EN-GJS-450-10 • Body & Bonnet: Ductile Iron
exterior surface which provides reliable corrosion resistance.
NBR/Fluororubber&Backing • Disc: D.I.+EPDM or D.I. + Bronze
3. Small hydraulic friction loss with reasonable structure design
2 Seat EPDM & Backing EPDM/NBR Vulcanized on Valve Body or Stainless Steel Sealing
Soft Seat in EPDM/NBR
• Bronze or Stainless Steel Seat
XD371X4 3 Disc EN-GJS-450-10 SS304, SS316, AL-Bronze C95400
• Fusion Bonded Epoxy Coating
4 Stem SS420, One-Piece Stem Design SS304, SS316, SS416, SS431
• Design Standard: BS EN 593
5 O-Ring NBR EPDM
• Connection Ends: BS EN 1092 PN10/PN16, AS 2129 TABLE E,
JIS B2212 10K, BS 10 TABLE D/E 6 Bushing PTFE Nylon 1010

• Top Flange Standard: ISO 5211 7 Signal Gear Box EN-GJS-450-10

Stem drive by keys, parallel or diagonal square or flat head
Note: For special material request other than standard specification, please indicate clearly on the inquiry or order list.
• Working Pressure: PN10/16
• Temperature Range: 0℃- 80℃ SWITCH WIRING DIAGRAM
• Coating: Fusion Bonded Epoxy Coating in accordance with Open (Red)
ANSI/AWWA C550 H44X2 H84X
Fire Alarm Control Common (White) Closed (Black) End of Line Resistor
Panel Supervisory Circuit or Next Device Flanged Resilient Swing Grooved Resilient Swing
Check Valve Check Valve
Page 28 Page 29
Actuator Case Ground (Yellow/Green Double Color)

Open (Yellow)

Common (Green) Closed (Blue) Aux. Device

Voltage Source
(Bell or Horn)

DN Dimensions(mm)

Inch mm A B M H H1 H2 H3 K G ØD C Ø2 L ISO 5211

2" 50 140.5 64.5 150 208 151 65 108 90 59 53.9 43 14 32 F07

2.5" 65 153 72 150 208 151 65 108 90 59 65.2 46 14 32 F07

3" 80 157.5 86 150 208 151 65 108 90 59 79.7 46 14 32 F07

4" 100 176 100 150 208 151 65 108 90 59 105 52 16 32 F07

5" 125 191 112 150 208 151 65 108 90 59 130 56 16 32 F07

6" 150 202.5 128 150 208 151 65 108 90 59 156 56 20 32 F07

8" 200 243.5 162 250 303 239 73 115 125 77.5 207 60 26 45 F10

10" 250 273 194 250 303 239 73 115 125 77.5 253.3 68 26 45 F10

12" 300 311 223 250 303 229 73 120 125 77.5 301.9 78 28 45 F10

Note: Not designed for dead end service

BS EN12334 Flanged Resilient Swing Grooved Resilient Swing
Check Valve (H44X2), PN10/16, Check Valve (H84X),
UL/FM Approved PN10/16, UL Listed

MATERIAL SPECIFICATION MATERIAL SPECIFICATION

Part No. Part Standard Specification Options Part No. Part Standard Specification Options
1 Valve Body EN-GJS-450-10 1 Valve Body EN-GJS-450-10

H44X2 2 Bonnet EN-GJS-450-10 H84X 2 Hinge Pin SS420

3 Flat Washer Carbon Steel Zinc Plated 3 Spring SS304 SS316

4 Bolts Carbon Steel Zinc Plated 4 Eye Bolt Carbon Steel Zinc Plated

• Connection Ends: Flange to BS EN 1092-2:1997 5 Eye Bolt Carbon Steel Zinc Plated • Connection Ends: Groove to ISO 6182 DN50-100 SS304
5 Disc SS304
DN150-300 EN-GJS-450-10
6 O-Ring EPDM NBR
• Working Pressure: PN10/16 • Working Pressure: PN10/16 6 Disc Sealing Ring EPDM NBR
7 Plug SS304 Bronze ASTM B584
• Temperature Range: 0℃- 80℃ • Temperature Range: 0℃- 80℃ 7 Seat Ring ASTM B62 C83600 (Pressed Fit) SS304, SS316 Pressed Fit or Threaded
8 O-Ring EPDM NBR
• Coating: Fusion Bonded Epoxy Coating in accordance with • Coating: Fusion Bonded Epoxy Coating in accordance with 8 Plug Malleable Iron Galvanized Bronze ASTM B584
9 Hinge Pin SS304 SS316
ANSI/AWWA C550 ANSI/AWWA C550 or painting upon request 9 Plug Malleable Iron Galvanized Bronze ASTM B584
10 Washer Brass ASTM B16 C36000/Hpb63-3 SS304
10 Plug Malleable Iron Galvanized Bronze ASTM B584
11 Hinge Bushing Brass ASTM B16 C36000/Hpb63-3 SS304
11 Plug Malleable Iron Galvanized Bronze ASTM B584
Bronze ASTM B62
12 Seat Ring SS304 12 Bolt SS304 SS316
C83600/ZQSn5-5-5(Pressed Fit)
13 Washer SS304 SS316
13 Disc Seat Bolts SS304
14 Nut SS304 SS316
Bronze ASTM B62
14 Retainer Washer
C83600/ZQSn5-5-5 Note: For special material request other than standard specification, please indicate clearly on the inquiry or order list.

15 Disc Seat Ring EPDM NBR

16 Disc EN-GJS-450-10
DN Dimensions(mm)
17 Clapper Arm EN-GJS-450-10
PN
18 Disc Bushing Brass ASTM B16 C36000/Hpb63-3 Inch mm L D1 D2 B C

19 O-Ring EPDM NBR 2" 50 16 171 57.15 60.3 7.93 15.88

20 Washer Brass ASTM B16 C36000/Hpb63-3 SS304 2.5" 65 16 184 69.09 73 7.93 15.88
Bronze ASTM B62 2.5" 65 16 184 72.26 76.1 7.93 15.88
21 Nut SS304
C83600/ZQSn5-5-5
3" 80 16 197 84.94 88.9 7.93 15.88
Note: For special material request other than standard specification, please indicate clearly on the inquiry or order list.
4" 100 16 210 110.08 114.3 9.53 15.88

DN Dimensions(mm)
5" 125 16 248 135.48 139.7 9.53 15.88
PN
Inch mm L D D1 d b E H n-Φd 5" 125 16 248 137.03 141.3 9.53 15.88
2" 50 10/16 203 165 125 99 19 3 133 4-Φ19 6" 150 16 324 160.90 165.1 9.53 15.88
2.5" 65 10/16 216 185 145 118 19 3 150 4-Φ19 6" 150 16 324 163.96 168.3 9.53 15.88
3" 80 10/16 241 200 160 132 19 3 243 8-Φ19 8" 200 16 371 214.40 219.1 11.13 19.05
4" 100 10/16 292 220 180 156 19 3 284 8-Φ19
10" 250 16 457 268.28 273.0 12.70 19.05
10
6" 150 356 285 240 211 19 3 290 8-Φ23 12" 300 16 535 318.29 323.9 12.70 19.05
16
10 8-Φ23
8" 200 495 340 295 266 20 3 330
16 12-Φ23
10 350 12-Φ23
10" 250 622 405 319 22 3 350
16 355 12-Φ28
10 400 12-Φ23
12" 300 698 460 370 24.5 4 376
16 410 12-Φ28
Y-Type Strainer Flanged Y-Type Strainer (V4),
PN10/16, UL Listed
• Statement:
Installed before relief valves, atmospheric valves, hydraulic control valves as well as
other equipments, strainers serve to filter out the impurities in the flow medium for
protection of valves and equipments in the piping system.

• Features:
1. Material: Ductile Iron EN-GJS-450-10
Valve body and cover are produced in ductile iron material which provides guarantee for
high strength and good corrosion resistance.
2. Different Options of Screen Mesh Specification
Different options of screen mesh specification available as per different service
conditions.
3. Fusion Bonded Epoxy Coating
Fusion bonded epoxy coating in accordance with ANSI/AWWA C550 for both interior and
exterior surface which provides reliable corrosion resistance. MATERIAL SPECIFICATION
• Ductile Iron Body & Bonnet V4
Part No. Part Standard Specification Options
• Stainless Steel Screen
1 Valve Body EN-GJS-450-10
• Fusion Bonded Epoxy Coating
2 Screen SS304 (Perforated) SS304, SS316 (Perforated, Knitted, Double Screen)
• Gasket: EPDM or Graphite + Acanthopore Plate • Connection Ends: Flange to BS EN 1092-2:1997
3 Gasket EPDM Graphite+Acanthopore Plate
• Working Pressure: PN10/16 4 Bonnet EN-GJS-450-10
• Temperature Range: 0℃- 80℃ rubber gasket, 5 Plug Malleable Iron Galvanized Bronze ASTM B584
-10℃- 350℃ graphite gasket 6 Bolt Carbon Steel Zinc Plated SS304, SS316

• Coating: Fusion Bonded Epoxy Coating in accordance with 7 Flat Washer Carbon Steel Zinc Plated SS304, SS316
ANSI/AWWA C550
STANDARD SCREEN

DN Hole Dia. Free Flow Area(%)

Sieve No.
Inch mm mm %
2"~2.5" 50~65 25 4 48
3"~4" 80~100 19 5 59
5" 125 14 6 63
6"~12" 150~300 13 6.3 64

Note: For special material request other than standard specification, please indicate clearly on the inquiry or order list.
V4 V8
Flanged Y-Type Strainer Grooved Y-Type Strainer
Page 31 Page 32 DN Dimensions(mm)
PN
Inch mm L D D1 D2 b n-Φd f H
2" 50 10/16 230 165 125 99 19 4-Φ19 3 140
2.5" 65 10/16 290 185 145 118 19 4-Φ19 3 175
3" 80 10/16 310 200 160 132 19 8-Φ19 3 198
4" 100 10/16 350 220 180 156 19 8-Φ19 3 229
5" 125 10/16 400 250 210 184 19 8-Φ19 3 287
6" 150 10/16 480 285 240 211 19 8-Φ23 3 304
10 8-Φ23
8" 200 600 340 295 266 20 3 370.5
16 12-Φ23
10 350 12-Φ23
10" 250 730 405 319 22 3 469
16 355 12-Φ28
10 400 12-Φ23
12" 300 850 460 370 24.5 4 540
16 410 12-Φ28
Grooved Y-Type Strainer (V8), Water Flow Indicator (ZSJZ),
PN10/16, UL Listed PN10/16

MATERIAL SPECIFICATION MATERIAL SPECIFICATION

Part No. Part Standard Specification Options Part No. Part Standard Specification Options
V8 1 Valve Body EN-GJS-450-10 1 Body EN-GJS-450-10
2 Screen SS304 SS316 2 Bolt Carbon Steel Zinc Plated SS304, SS316
3 Rigid Coupling EN-GJS-450-10 3 Lodicule Plastic
ZSJZ
• Connection Ends: Groove to ISO 6182 4 Cap EN-GJS-450-10 4 Nut Carbon Steel Zinc Plated SS304, SS316
5 Plug Malleable Iron Galvanized Bronze ASTM B584 5 Gasket EPDM NBR
• Working Pressure: PN10/16 • Connection Ends: ISO 6182
Note: For special material request other than standard specification, please indicate clearly on the inquiry or order list.
• Temperature Range: 0℃- 80℃ STANDARD SCREEN • Working Pressure: PN10/16
• Coating: Fusion Bonded Epoxy Coating in accordance with DN Hole Dia. Free Flow Area(%) • Temperature Range: 0℃ - 80℃
Sieve No.
ANSI/AWWA C550 or painting upon request Inch mm mm %
• Coating: Fusion Bonded Epoxy Coating in accordance with DN Dimensions(mm)
2"~2.5" 50~65 25 4 48 ANSI/AWWA C550 Inch mm R A B C D
3"~4" 80~100 19 5 59
2" 50 60.3 62 48 36 120
5" 125 14 6 63
2.5" 65 73 62 48 31 130
6"~12" 150~300 13 6.3 64
2.5" 65 76.1 62 48 31 130
Note: For special material request other than standard specification, please indicate clearly on the inquiry or order list.
3" 80 88.9 62 48 36.5 145
4" 100 114.3 62 48 30.5 185
DN Dimensions(mm) 5" 125 139.7 62 48 36.5 221.5
Inch mm L OD d A B 5" 125 141.3 62 48 36.5 221.5
2" 50 247.5 60.3 57.15 15.88 7.92 6" 150 165.1 62 48 33 254
2.5" 65 273 73 69.09 15.88 7.92 6" 150 168.3 62 48 33 254
2.5" 65 273.0 76.1 72.26 15.88 7.92 8" 200 219.1 62 48 36.5 300
3" 80 298.5 88.9 84.94 15.88 7.92
4" 100 362.0 114.3 110.08 15.88 9.52
5" 125 419.0 139.7 135.48 15.88 9.52
5" 125 419 141.3 137.03 15.88 9.52
6" 150 470.0 165.1 160.90 15.88 9.52
6" 150 470.0 168.3 163.96 15.88 9.52
8" 200 609.5 219.1 214.40 19.05 11.13
10" 250 686.0 273.0 268.28 19.05 12.70
12" 300 762.0 323.9 318.29 19.05 12.70
Landing Valve(SN), Wet Alarm Check Valve
PN10/16

• Statement:
The alarm check valve works as a check valve by preventing the reverse flow of water from the
system piping to the water supply. The valve is trimmed with a water bypass line, which has an
in-line swing check valve. The bypass line allows pressure surges to enter the system and to
be trapped above the alarm check valve's clapper without the clapper lifting and causing false
alarms.
When a significant flow of water occurs, such as from an open sprinkler, the alarm valve's
clapper lifts and allows water to enter the system. Simultaneously, water enters an intermediate
chamber, which allows the water to activate an alarm either through a water motor alarm or
through a water pressure alarm. These alarms continue to sound until the flow of water is
stopped.
MATERIAL SPECIFICATION

Part No. Part Standard Specification

1 Body EN-GJS-450-10 DN Dimensions(mm)
2 Disc EN-GJS-450-10+EPDM Equivalent Length
Inch mm OD
3 Steel Ball SS304 of Pipe (m)
SN
3" 80 88.9 4.9
4 Inner Hex Screw SS304
4" 100 114.3 7.9
• Thread: ISO 7-1 5 Stem SS420
6" 150 165.1 9.8
• Working Pressure: PN10/16 6 O-Ring NBR
6" 150 168.3 9.8
7 Bonnet EN-GJS-450-10
• Temperature Range: 0℃ - 80℃ 8" 200 219.1 8.2
8 O-Ring NBR
• Coating: Fusion Bonded Epoxy Coating in accordance with 9 Handwheel ABS
ANSI/AWWA C550
10 Screw SS304

6.0

RESSURE DDROP – PSI

DN Dimensions(mm) 5.0

Inch mm H1 H2 L d1(Rc) d2 D(R)

2" 50 57.5 109.5 63 2 44.5 2
4 0
4.0
2.5" 65 71 109.3 71 21/2 58 21/2

PRESSURE
3.0

2.0

PR
1.0
0 9
0.9

0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
10 20 30 40 60 80 100 200 300 400 600 1000 2000 4000 6000 10000 20000

FLOW RATE – GPM