NAFFCO INDIRECT LOW PRESSURE SYSTEM – ABC/BC DRY

CHEMICAL

NAFFCO INDIRECT LOW PRESSURE AUTOMATIC FIRE SUPPRESSION SYSTEM

GENERAL DESCRIPTION SYSTEM OVERVIEW

The NAFFCO automatic In-direct low pressure systems The system utilizes flexible heat detection tubing that
are total flooding system that consists of a flexible is attached to the top of the cylinder valve. This tubing
polymer tube, a large capacity tank filled with acts as a continuous linear thermal detector that
extinguishing agent (dry chemical powder) associated ruptures to create a diffuser upon direct flame
with a CO2 flush tank and a pipe system. Each installed impingement or at high temperatures associated with
system is equipped with detection tubing, discharge
fire conditions. Under the effect of a rise in
piping, and nozzles. The pre-designed concept
temperature or the appearance of a flame, the tube
minimizes the amount of engineering involved in the
application design. bursts, the CO2 of the flush tank is thus released into
By running the tubing directly above the area to be the large capacity cylinder and expels the extinguishing
protected you will minimize the time it takes to detect agent on the fire source through the extinguishing
and suppress the fire. In ILP system Dry powder is stored pipeline distributing the extinguishing agent through
in a steel cylinder. the nozzles into the protected area. In a few seconds,
PRODUCT FEATURES the disaster is under control. Each cylinder is equipped
with a Nickel plated brass valve, a pressure gauge to
 Indirect low pressure (ILP) Systems are simple,
monitor cylinder pressure, an integrated quarter turn
balanced-flow configurations.
ball valve with pressure gauge to monitor heat
 ILP System require no external power to operate, detection tubing pressure.
and very little maintenance.
 Minimum design and installation time. ABC/BC DRY POWDER EXTINGUISHING AGENT
 ILP system are equipped with its own detection ABC/BC dry powder has been treated to be water
tubing and discharge nozzles. repellent and capable of being fluidized and free
 Quick acting so only minimal damage is done to the flowing so that it can be discharged through hoses and
protected space. piping under the influence of an expellant gas. When
discharged, dry powder will drift through the air and
 Additional benefit of deployment from the tubing settle on surrounding surfaces.
burst means that all areas are covered even if they
were not initially identified as a primary risk.
 Can be combined to protect a larger size hazard,
and can be simultaneously actuated.
 System can be easily replaced after fire has taken
place.
 The system can also be fitted with a pressure switch
that constantly monitors the contents of the
container and can be used to sound an alarm or be
integrated into an existing fire alarm panel.

IDEAL FOR:
 Flammable chemicals,
 Storage areas,
 Partially open areas,
 Waste storage,
 Chemical storage
 Painting Room
 Painting Storage

Doc. No. NF/DS/ILP-ABC-HC Rev: 00 Date: 21/11/2019 Page: 1

 NAFFCO INDIRECT LOW PRESSURE SYSTEM – ABC/BC DRY
CHEMICAL

COMPONENT DETAILS
Automatic Fire Detection tubing is perfectly applicable for fire suppression systems, as it acts like sensor tubing
1. HEAT DETECTION TUBING & ACCESSORIES
for the purpose. It is more efficient and cost effective compared all other mechanical means. The key advantages
of this Fire Detection Tubing includes Multi-layer construction is more resistant to temperature extremes,
chemical agents and UV stabilization against UV, can be pressurized even up to 24 Bar while in operation and
have the ability to react quickly to the temperature of a fire in its young stage.

HEAT DETECTION TUBE QUICK CONNECT FITTINGS END OF LINE DEVICES

Outside diameter: 6mm Connection Size: Ø 6 mm Includes: pressure gauge, connection for
Inside diameter: 4 mm Material: Nickel Plated Brass filling adaptor and fitting to connect to
Bursting Temperature: 110°C sensor tubing Large, easily visible knob
Yellow safety collar

SELD-ADHESIVE CLIP & BINDING TIE SCREWED CLIP DISCHARGE NOZZLE

Material: Polyamide Material : Aluminium & Chloroprene Material : Aluminium
Self-adhesive base Diameter: 6 mm

LOW PRESSURE BALL VALVE SECURITY CLIP THROUGH PANEL FASTENER

Inlet connection: G ¼’’ Male Locks the ball valve in the Open Exerts radial compression when tightened
Outlet Connection: G 1/8’’ Female position to securely hold tubing in place, Material:
Nylon

Doc. No. NF/DS/ILP-ABC-HC Rev: 00 Date: 21/11/2019 Page: 2

 NAFFCO INDIRECT LOW PRESSURE SYSTEM – ABC/BC DRY
CHEMICAL

TYPICAL SYSTEM LAYOUT

POS QTY DESCRIPTION

1 1 Agent Cylinder

2 1 CO2 Cartridge Cylinder

3 1 Indirect Low Pressure Valve

4 1 Heat Sensor tubing

5 1 Discharge Pipe

6 1 Discharge Nozzle

7 1 End of Line Device

MODEL NFILP25ABC NFILP50ABC NFILP100ABC

Agent capacity 25 Kg 50 Kg 100 Kg
Number Of Nozzles 5 6 8
CO2 Cylinder Capacity 1 Kg 1.5 Kg 2 Kg

Operating Temperature -20°C to 60°C

Working Pressure 15 bar

Siphon Tube Yes
Sensor Tubing Color Black

Risk Coverage Less Than 5 M² Less Than 15 M² Less Than 30 M²

Doc. No. NF/DS/ILP-ABC-HC Rev: 00 Date: 21/11/2019 Page: 3

 NAFFCO INDIRECT LOW PRESSURE SYSTEM – ABC/BC DRY
CHEMICAL

OPTIONAL DEVICES

SL.NO. ITEM DESCRIPTION

1 Manual Release Device
2 Solenoid Release Device
3 End Plug
4 End of Line Adapter
5 Pressure Gauge
6 Pressure switch
7 Sensor Tube
8 Discharge Nozzle
9 Filling Cap
10 Safety Release
11 Pilot Hose
12 Indirect High Pressure Valve

Doc. No. NF/DS/ILP-ABC-HC Rev: 00 Date: 21/11/2019 Page: 4