File No.

ENE51-PM0SYI(400)/12/2021-EE2

TRANSMISSION CORPORATION OF ANDHRA PRADESH LIMITED

Vidyut Soudha: Vijayawada -520004
APTRANSCO- Standard Schedule of Rates-2020-21 for labour & equipment/material for adoption
in construction and O&M works pertaining to 400kV, 220kV & 132kV transmission lines &
substations – communicated – Reg.
-----------------------------------------------------------------------------------------------------------------------
T.O.O Chief Engineer (Transmission) Ms. No. 2220 Dt. 29-07-2021
Read the following: -

Ref:- T.O.O No. ED (Construction)/ [Link]. 1388, Dt: 17.2.2020

APTRANSCO is periodically communicating Standard Schedule of Rates for labour & material
for construction and O&M works pertaining to 400kV, 220kV & 132kV transmission lines &
substations for adoption in preparation of estimates. Accordingly, the SSR communicated earlier in
the reference cited is revised and communicated herewith.

ORDER

Standard Schedule of Rates for labour & material for construction and O&M works pertaining to
400kV, 220kV & 132kV transmission lines & substations approved by TRANSMISSION
CORPORATION OF ANDHRA PRADESH LIMITED is communicated herewith for adoption in
preparation of estimates.

The SSR 2020-21 will come into force from the date of issue of this T.O.O and shall be valid till
further orders

(BY ORDER AND IN THE NAME OF TRANSMISSION CORPORATION OF ANDHRA

PRADESH LIMITED)
#ApprovedByName#

Sd/-
K Praveen Kumar
Director (Grid, Transmission & Management)

To
All
The Chief Engineers.
The FA&CCA/VS/APTRANSCO.
The Superintending Engineers.
The SAOs.
The Executive Engineers.

PS to Chairman and Managing Director/APTRANSCO/VS/Vijaywada.

PS to Joint Managing Director/ APTRANSCO /VS/Vijayawada.
PS to Joint Managing Director/(Vigilance & Security)/ APTRANSCO /VS/Vijayawada.
PS to The Director/Grid & Transmission) Management/ APTRANSCO /VS/Vijayawada.
PS to The Director/Finance
 File No.ENE51-PM0SYI(400)/12/2021-EE2

TRANSMISSION CORPORATION OF ANDHRA PRADESH LIMITED

STANDARD SCHEDULE OF RATES FOR

LABOUR ITEMS OF 400 KV, 220KV &
132 KV TRANSMISSION LINES AND
SUBSTATIONS WORKS AND FOR O&M
WORKS OF TRANSMISSION SYSTEM

&

MATERIAL RATES FOR 400 KV, 220 KV

&132 KV TRANSMISSION LINES AND
SUBSTATIONS

FOR THE YEAR 2020-21

 File No.ENE51-PM0SYI(400)/12/2021-EE2

INDEX
VOLUME-I
LABOUR RATES

SI. Description Page No

No.
1 Preamble: 1
2 ANNEXURE-I: 6
Erection of 400kV Transmission Lines
3 ANNEXURE-II:
8
Erection of 220kV & 132kV Transmission Lines
4 ANNEXURE-III:
Erection of 400kV Substations 11

5 ANNEXURE-IV:
14
Erection of 220kV & 132kV Substations
6 ANNEXURE-V:
Erection of Illumination, Lighting, Fire Fighting, Air-conditioning, 18
D.G Set & 33kV Station Supply Systems in 400kV Substations.
7 ANNEXURE-VI:
Handling charges of Equipment & Line Materials 24
8 ANNEXURE-VII:
Transportation & Handling Charges pertaining Erection of 400kV 29
Transmission Lines
9 ANNEXURE-VIII:
Transport of 220kV & 132kV Substation Equipment and 30
Transmission Line Materials.
10 ANNEXURE-IX:
Handling & Erection of Power Transformers 31
11 ANNEXURE-X:
O&M Works of EHT Lines 37
12 ANNEXURE-XI:
39
Erection of Telecom Equipment
13 ANNEXURE-XII:
Laying of EHT UG Cables 43
14 ANNEXURE-XIII Rates of the items of works(Line & Substations)
involved under special conditions 60
 File No.ENE51-PM0SYI(400)/12/2021-EE2

INDEX
VOLUME-II
EQUIPMENT/MATERIAL RATES

SI. Description Page No

No.
Equipment/Material Rates for 220kV & 132kV Substations &
1 62
Lines

2 Equipment/Material Rates for 400kV Substations & Lines 68

3 Equipment/Material Rates for Telecom equipment 83

4 Auto/Power transformer and reactors 88

5 SAS Equipment/Material 89

6 XLPE Power cables rates 91

7 GIS Equipment/Material Rates 93

8 Visual Monitoring Systems 95

File No.ENE51-PM0SYI(400)/12/2021-EE2

PREAMBLE
 File No.ENE51-PM0SYI(400)/12/2021-EE2

PREAMBLE

1. The rates for the item of works (Line & Substations) involved under special conditions in
the SSR-19-20 are also continued in SSR-2020-21 vide Annexure-XIII.
2. For EHT (400kV, 220kV & 132kV) Transmission line works: Uniform Area Allowance
including Scattered area Mobilization efforts is provided as follows: -

a. 20% extra provision on the basic rates of APTRANSCO towards Uniform Area
Allowance including Scattered area Mobilization efforts in general areas

b. 35% extra provision on the basic rates of APTRANSCO towards Uniform Area
Allowance including scattered area Mobilization efforts in difficult area
/Scheduled terrain. The concerned SE/TLC has to certify that entire line passes
through difficult area / Scheduled terrain duly furnishing the justification.

Note:- If 35% extra toward Uniform Area Allowance including Scattered area
Mobilization efforts in difficult area/ Scheduled Terrain is applicable for a
work, then the 20% extra towards Uniform Area Allowance including
Scattered area Mobilization efforts in general areas is not applicable.

c. 10% extra to the rate of earth flat (material) is allowed towards wastage, cleats and
overlap etc., while preparing the estimate as the billing for this item is on Running
Meters basis after laying of earth mat.

d. For stringing of conductor for small modification works, if the length of the line
is less than 0.5 KM, 0.5KM is considered and if the length of the line is greater
than 0.5 KM and less than 1 KM, 1KM is considered, in the preparation of
estimate.

e. For survey of small length of lines, if the length of line is less than 1KM, then
1KM is considered for survey of small length of lines in the preparation of
estimate.

f. The rates for tree cutting and jungle clearance may be followed as per Common
SoR of Government of Andhra Pradesh.

3. Area Allowances:

a. 35% extra over the basic rates on labour component of works is allowed in
Greater Visakhapatnam Municipal Corporation and Vijayawada Municipal
Corporation.
b. 20% extra over the basic rates on labour component of works is allowed in other
Municipal Corporations.

c. 15% extra over the basic rates on labour component of works is allowed in
district headquarters and other municipalities.

1
 File No.ENE51-PM0SYI(400)/12/2021-EE2

Note: Works within a belt of 12Km from the Municipal limits shall be taken into account for
the purpose of allowing the extra percentages.

d. Agency Areas:
1. 25% extra is allowed for the works located inside the Agency area.
2. 15% extra is allowed for the works located in the border of Agency area i.e.,
works located within a belt of 16Km from the boundary of Agency area.

Note: If more than one area allowances (such as those) for Municipal Corporation
Municipalities, Agency areas are applicable for a particular situation, only the
maximum out of the allowable percentages is to be allowed.
e. The Area allowance/Uniform Area Allowance including scattered area
Mobilization efforts charges are not applicable on Fabrication charges and
Galvanization Charges.
f. The area allowance shall be applicable for O&M and RMI works in substations
also on par with construction works.
g. The Uniform Area Allowance including scattered area Mobilization efforts shall
not be applicable for O&M & RMI works of lines.

The area allowances are applicable for Civil & Electrical works (labour), where
the value of work is more than Rs.20.00 lakhs (electrical & civil).

4. 7.25% on basic labour rates towards for COP (Contractors Overheads and Profit)
including labour importation is applicable only for turnkey projects (new Substations,
Lines 33KV features and Bay Extension works ) of more than 1 crore and not applicable
to O&M works and other than turnkey works. The following components of COP
relevant/pertaining to APTRANSCO are considered.
a. Site accommodation.
b. Setting up of plants and machinery.
c. Formation of access road.
d. Water supply for construction.
e. Electricity for construction.
f. Technical agents for site supervisions.
g. Documentation and as built drawings.
h. Mobilization/de-mobilization of resources.
i. Labour camps with minimum amenities and transportation to work sites.
j. Light vehicle for site supervision including field and laboratory testing.
k. Laboratory equipment and quality control including field and laboratory testing.
l. Watch & Ward.

5. Tree Cutting and Clearing of Jungle

Please refer to the prevailing Common SoR of Board of Chief Engineers for engineering
departments of GOAP.

6. The (lead) Conveyance Charges for Transportation of Equipment /Materials.

Please refer to the prevailing SoR of Board of Chief Engineers for engineering
departments of GOAP.

2
 File No.ENE51-PM0SYI(400)/12/2021-EE2

7. Erection of Power Transformers and Oil filtration Works

The rates communicated by CE/Transmission vide letter [Link](Tr)/SE(Tr)/EE(Tr)/DEE-
2/[Link] Vol-4-1/[Link].66/21 dated.24-03-2021 and [Link](Tr)/SE(Tr)/EE(Tr)/DEE-
2/[Link] 400KV-Oil Filtration/[Link].75/21,dt.31-03-2021 on rate contract basis for
erection, dismantling, transportation and oil filtration of power transformers through
private agency are valid up to 31.03.2023.
Area Allowances, Special provisions and any other allowances are not applicable on
the rates of rate contract. The rates mentioned under the rate contract include all taxes &
duties, allowances and all extra provisions including Transport etc.
In the case of the works of Handling, Erection and Filtration of power Transformers
will be carried out by the department, in such cases, area allowances, special provisions
other than shutdown charges, taxes and duties are not applicable.
Note:
(i) Shutdown charges are applicable only for the works carried out during
shutdown period. The same has to be certified by the concerned Superintending
Engineer.
(ii) Whenever double boom crane is utilized for PTR works of 80 MVA & above
capacity, 50% extra over the existing crane charges are applicable. However,
the same has to be certified by concerned Superintending Engineer.

8 Civil Engineering Works in APTRANSCO:

For Civil work items of APTRANSCO, the prevailing common SoR of Board of
Chief Engineers for engineering departments of GOAP shall be followed in toto except
area allowances & Contractors Profit and overheads (COP).
The Area allowances of APTRANSCO SSR-2020-21 at Para 4 is also applicable for
Civil Works and a provision is made for 7.25% towards Contractors Profit and overheads.
The provisions made in [Link] (Civil) Ms No.148, dated.21.10.2009 are also
applicable for civil works except the Uniform area allowance & Scattered area allowance.
The Uniform Area Allowance including scattered area Mobilization efforts charges at
Para 2 is also applicable for Civil Works (Transmission Line).

9. The rates for the following equipment/ material pertaining to IT will be adopted from the
GEM (Government e-market place) portal.

a) For Servers, Work Stations, Load Balances, SAN storages, SAN Switches, tape
Library, Routers/Access Points, Firewalls, Switches, Racks and Hubs.
b) Desktops, Laptops, All in ones, Tablets, Printers, Monitors, UPS, Scanners, toner
cartridges, CAT V & VI Cables, for use in office only.
c) MS Office, MS Windows, Backup Software and Antivirus software.
d) Computer related items for use in SAS are to be adopted from SSR.
e) In future, if any items are not available in the GEM portal, the rates will be arrived as
per guidelines.

10. In respect of Cement and Steel rods the procedure indicated in Common SSR for all
Engineering Departments shall be adopted for updating of estimates at the time of
finalization of tenders.

3
 File No.ENE51-PM0SYI(400)/12/2021-EE2

11. All statutory levies such as GST, Cess for labour welfare if any, are based on the
prevailing notified rate, shall have to be added in the estimate.

12. The S.S.R will come into force with immediate effect until further orders.

4
File No.ENE51-PM0SYI(400)/12/2021-EE2

VOLUME-I
LABOUR RATES

5
 File No.ENE51-PM0SYI(400)/12/2021-EE2
ANNEXURE – I
SS RATES FOR ERECTION OF 400KV TRANSMISSION
LINES
SS Rate for
Item 2020-21
Sl. No. Description of Item Unit
No. (in Rs)
Preliminary Survey with GPS survey, theodilite &
C4L1 1(a) total station, marking route on topo sheets represents actual kM 4,374.19
field conditions.
Detailed Survey with GPS, total stations, Digital
theodolite etc., along the approved alignments
C4L 2 1(b) kM 22,723.15
preparation of profiles, tower spotting, tower schedules
and soil resistivity.
C4L 3 2(a) Excavation of trail pit (1mt x 1 mt x 3.5mt). No. 2,258.31
Excavation of Trial Pit by Auguring & Boring
2(b) No. 2,516.07
of holes of 300mm Dia x 3.5 RM.
Check Survey, peg marking the tower positions on
ground,conforming to the approved Profile and tower
C4L 4 3 kM 5,174.98
schedules using
GPS, Total stations, Digital theodolites etc.
Setting with stub for all types of towers withstub
setting template which includes erection ofstubs, fixing
C4L 5 4 of jacks for supporting template, alignment and leveling Set 18,438.79
excluding cost of excavation and concrete
(excluding transportationcharges).
Super structure erection of all type of towers including
extensions except RC towers including fitting of step
bolts, danger plates, number plates, phase plates, circuit
C4L 6 5(a) plates, bird guards, anti-climbing devices etc., and tack MT 9,895.74
welding of all bolts & nuts (upto bottom cross
arm level) (excluding transportationcharges).
Erection of all types of Anchor Towers and their
extensions (complete), including fitting of step bolts, danger
C4L 7 5(b) plates, number and phase plates, circuit plates, bird MT 14,843.61
guards, and anti climbing devices etc and tack welding
of all bolts & nuts (upto bottom cross arm level).
Super structures erection of 400kV Multi circuit towers
including Auxiliary cross arms (complete), including
fitting of step bolts, danger plates numbers and phase
C4L 8 5(c) MT 17,614.53
plates, circuit plates, birds guards, and anti climbing
devices etc and tack welding of all bolts & nuts (upto
bottom cross arm level) etc.
Super structure erection of River crossing towers and
their extensions(complete), including all the associated
works such as, earthing of all the four legs as per the
approved drawing(including the cost of material),fitting of
C4L 9 5(d) step bolts, danger plates, number and phase plates, circuit MT 24,722.51
plates, bird guards, and anti climbing devices etc and
tack welding of all bolts & nuts (upto bottom cross arm
level).

6
 File No.ENE51-PM0SYI(400)/12/2021-EE2
SS Rate for
Item 2020-21
Sl. No. Description of Item Unit
No. (in Rs)
Mounting of Insulators and stringing of double circuit with
twin bundled ACSR Moose Power Conductor including
C4L 10 6 laying, jointing, tensioning, sagging clamping and fixing
spacers (excluding transportation charges).

6(a) Single circuit Stringing KM 2,62,581.37

6(b) Double Circuit Stringing KM 3,93,872.04
6(c) Multi Circuit Stringing (4 circuits) KM 5,90,808.06
Mounting of Insulators and stringing of double circuit with
Quadruple ACSR Moose Power Conductor including
C4L 11 7 laying, jointing, tensioning, sagging clamping and fixing
spacers (excluding transportation charges).
7(a) Single circuit Stringing KM 3,93,872.04
7(b) Double Circuit Stringing KM 5,90,809.66
7(c) Multi Circuit Stringing (4 circuits) KM 8,86,214.50
Mounting of Insulators and stringing of double circuit with
twin bundled ACSR Moose Power Conductor including
C4L 12 8 laying, jointing, tensioning, sagging clamping and fixing
spacers (excluding transportation charges) for River crossing
tower.
C4L 13 8(a) Double Circuit Stringing KM 9,83,913.11
8(b) Multi Circuit Stringing(4 circuits) KM 14,75,869.66
Stringing of two (2) nos. 7/3.66 mm galvanized steel earth
wire, including laying jointing, tensioning etc., with necessary
C4L 14 9(a) KM 18,506.18
accessories upto the pinnacle (excluding transportation
charges).
Stringing of one (1) no. 7/3.66 mm galvanized steel earth
C4L 15 9(b) wire, including laying jointing, tensioning etc., with KM 12,337.98
necessary accessories (excluding transportation charges).
Stringing of two (2) nos. 7/3.66 mm galvanized
steel earth wire, including laying jointing, tensioning etc.,
C4L 16 9(c) with necessary accessories upto the pinnacle(excluding KM 46,230.96
transportation charges) for River crossing towers.

C4L 17 9(d) Stringing of two (2) nos. OPG Wire, including laying jointing,
tensioning etc., with necessary accessories.(excluding KM 91,110.79
transportation charges).
Stringing of one (1) no. OPG Wire, including laying jointing,
C4L 18 9(e) tensioning etc., with necessary accessories.(excluding KM 60,739.99
transportation charges).
10 Earthing of transmission towers:
Providing of Pipe type earthing including of cost of BH
C4L 19 10(a) coke & salt but excluding cost of earthing set Each 5,070.63

Counter poise earthing sets excluding cost of all materials Each

C4L 20 10(b) 4,250.64
(4sides of tower) location
Counter poise earthing sets using Bentonite and salt (4 sides of Each
C4L 21 10(c) tower) 6,376.79
location

7
 File No.ENE51-PM0SYI(400)/12/2021-EE2
ANNEXURE - II
ERECTION OF 220kV & 132 kV TRANSMISSION LINES
SS Rate for
Sl. Item 2020-21
Description of Item Unit
No. No.
(in Rs)
CL1 1 Check Survey, peg marking the tower positions on ground, kM
conforming to the approved Profile and tower schedules using
GPS, Total stations, Digital theodolites etc. 5,174.98
"the rate is also applicable for re-check survey if any done due to
ROW problems"
CL2 2 Conducting reconnoitery and preliminary survey along bee line RKM
with three alternative routes and furnishing report for selecting the
best proposal for approval, including cost & conveyance of all
materials, hire charges of equipment, tools and plant, preparation 4,700.58
of drawings and reports, labour charges, complete for finished
item of work as per the directions of Engineer-in-charge at
site.(With Theodolite / With GPS equipment ( As per Clause 4.9
of survey) /With total station equipment).
3 Conducting detailed survey by taking the levels along the route to
a corridor of 15 mtrs. width on either side of alignment, at every
20 mtrs. interval and wherever there is a steep increase/decrease in
ground profile duly indicating the chainage between angle points,
river crossings, railway crossing and major highway crossings and
plotting the profiles and preparation of vicinity maps to the
standard scales. The survey includes clearing of bushes, branches
of tree, crops and shrubs wherever encountered for detailed survey
for viewing, for fixing anchor towers and also taking levels etc.
required for conducting detailed surveys.
This work can be done with Theodolite or with GPS equipment
(As per clause no.4.9 of survey) or with total station equipment.
This work involves the following items.
CL3 i) Tower schedules as per tower spotting requirements plotted on RKM
reproducible tracing of profile original with one extra copy shall
be given . Towers Schedules should be submitted with GPS Co- 16,138.04
ordinates. Identification of wind zones, collection of Hydraulic
data of rivers / drains from competent authority.
CL4 ii) Taking earth resistivity at an interval of 1 Km by electrical Loc
1,174.47
resisitivity method (4 point method) or by ERM method.
CL5 iii) Preparing of PTCC questionnaire, topo sheets extracts with Job
marking of the proposed line. Soil resistivity report, tower sketch, 11,487.75
station single line diagram etc. (30 copies/sets)
CL6 3 iv) Enumeration and numbering of trees, & marking on tree with Each
white letters on yellow paint measuring girth and height of the
trees and plotting in the profile. The trees enumerated shall be
shown in profile on either side of centre line clearly, up to
23.09
required corridor for 132kV Line -27 Metres & 220kV Line -35
Meters) indicating name of tree, girth & height. Separate tree
schedule should be submitted along with the profile for arriving
tree compensation amount.
CL7 3 (v) Preparation of ground profiles for Railway crossing, River Each
crossing and EHV power line crossing separately wherever crossing 3,497.56
required.
The above rates shall include cost and conveyance of all materials
hire charges of equipment tools & plant, preparation of profile
drawing, painting of trees, labour charges, preparation of report
etc., complete for finished item of work as per instructions of
Engineer-in-charge.

8
 File No.ENE51-PM0SYI(400)/12/2021-EE2
SS Rate for
Sl. Item 2020-21
Description of Item Unit
No. No.
(in Rs)
CL8 4 Excavation of trial pits of standard dimensions of 1 mtr X 1 mtr. Each
width upto 3 mtrs. depth at 1 KM interval or wherever there is
abnormal change in topography and taking observation of soil
strata for classification of foundation and position of existing 1,935.69
ground water table/depth of water in the existing open wells if any
and back filling the trial pits after vetting by Departmental
officials.
5 Setting of stubs with stub-setting template : Erection of stubs, stub
template, fixing of jacks for supporting template, allignment and
levelling for exact location of stubs of stubsetting template,
dismantling of template after completion of initial curing of C.C.,
movement of template from one location to other location
(A minimum lead of 1 KM is adopted).
CL9 (a) 132 KV P, R & S-Type Towers Loc. 9,236.68
CL10 (b) 220 KV A, B, C & D-Type Towers Loc. 13,460.16
CL11 (c) 132 KV Multi circuit Towers Loc. 11,546.19
CL12 (d) 220 KV Multi circuit Towers Loc. 16,823.14
CL13 (e) 132kV Narrow based Multi Circuit Towers. Single pit 10,616.42
CL14 (f) 220kV Narrow based Multi Circuit Towers. Single pit 15,489.64
CL15 (g) Pole/structure for termination of 220/132kV cables Loc. 10,390.77
CL16 (h) 220 /132 kV Narrow based tower Loc. 15,141.63
CL17 6(a) Erection of tower structures, including all types of extensions MT
except JC type towers (stub template erection and dismantling are
6,114.28
not to be included) (including 3 mtr., 6 mtr. , 9 mtr., & 12 mtr.
extensions)
CL18 6(b) Erection of all types of narrow based towers / multi circuit tower MT
structures / narrow based multi circuit towers structures, including
all types of extensions except JC type towers (stub template 8,566.54
erection and dismantling are not to be included) (including 3
mtr., 6 mtr. , 9 mtr., & 12 mtr. extensions)
CL19 6(c) Erection of all types of 'JC' Type tower structures, including all MT
types of extensions (stub template erection and dismantling are not 11,011.99
to be included) (including '0' based, Extended and Truncated)

CL20 6(d) Erection of pole/structure for 220/132 kV cable termination MT 7,340.42

7 STRINGING OF POWER CONDUCTOR: Hoisting of tension
insulators and Suspension insulators, paving out the conductor,
rough sagging,Jointing, tensioning, clipping and fixing of
preformed Armour rods and vibration dampers. measuring ground
clearances wherever [Link] excludes the works involved
in the crossing of LT, 11kV & 33kV power lines viz dismantling
and restringing of conductor
CL21 (i) 3 Nos. Zebra conductors RKM 52,146.85
CL22 (ii) 6 Nos. Zebra conductors RKM 78,217.55
CL23 (iii) 2 Nos. Panther conductors RKM 27,805.23
CL24 (iv) 3 Nos. Panther conductors RKM 41,712.60
CL25 (v) 6 Nos. Panther conductors RKM 66,050.13
CL26 (vi) 12 Nos. Panther conductors for Multi circuit RKM 1,32,100.27
CL27 (vii) 2 Nos. Moose conductors RKM 44,032.98
CL28 (viii) 3 Nos. Moose conductors RKM 66,050.13
CL29 (ix) 6 Nos. Moose conductors RKM 1,04,284.19
CL30 (x) Twin bundled Moose for DC RKM 2,08,568.38
CL31 (xi) 12 Nos. Moose conductors for Multi circuit RKM 2,08,568.38
CL32 (xii) 3 Nos. Bear conductors RKM 52,146.85
CL33 (xiii) 6 Nos. Bear conductors RKM 78,217.55

9
 File No.ENE51-PM0SYI(400)/12/2021-EE2
SS Rate for
Sl. Item 2020-21
Description of Item Unit
No. No.
(in Rs)
CL34 (xiv) 3 Nos. Dog conductors RKM 31,283.76
CL35 (xv) 6 Nos. Dog conductors RKM 49,535.57
STRINGING OF HTLS POWER CONDUCTOR using tension -
puller machine: Hoisting of tension insulators and Suspension
insulators, paving out the conductor, rough sagging,Jointing,
tensioning, clipping and fixing of preformed Armour rods and
vibration dampers. measuring ground clearances wherever
[Link] excludes the works involved in the crossing of
LT, 11kV & 33kV power lines viz dismantling and restringing of
conductor.
CL36 (i) 3 Nos Moose Conductors RKM 2,44,680.50
CL37 (ii) 6 Nos Moose Conductors RKM 3,67,020.75
CL38 (iii) 3 Nos Zebra Conductors RKM 2,31,087.14
CL39 (iv) 6 Nos Zebra Conductors RKM 3,46,630.71
CL40 (v) 3 Nos Panther Conductors RKM 2,17,493.78
CL41 (vi) 6 Nos Panther Conductors RKM 3,26,240.67
CL42 8 Stringing of Earthwire: FIxing hardware, paving out earth wire, RKM
jointing, tensioning, stringing and clamping of 7/3.15 mm high 8,346.33
tensile galvanised steel wire.
CL43 9 Earthing of towers including cost of Excavation, Back-filling, Nos.
including cost of 25 mm dia 2.5 mm thick, class 'C' G.I. pipe of
5,306.84
3.00 Mtrs length with 50X6 mm G.I. Flat 4.05 Mtrs long, BH
Coke , Salt etc., and measuring tower footing resistance.
CL44 10 Slant Earthing of towers including cost of Excavation, Back- Nos.
filling, including cost of 25 mm dia 2.5 mm thick, class 'C' G.I.
5,306.84
pipe of 3.00 Mtrs length, with 50x6mm G.I. Flat of 4.05 Meters,
BH Coke, Salt etc., and measuring tower footing resistance.
CL45 11 Earthing of towers including cost of Excavation, Back-filling, Nos.
including cost of 25 mm dia 2.5 mm thick, class 'C' G.I. pipe of
3.00 Mtrs length,BH Coke , Salt etc., and measuring tower footing 4,319.98
resistance. (Without GI Flat ) for counter poise earthing.
CL46 12 Counterpoise earthing including clamping devices and terminal Rmts
lugs, but excluding cost of steel wire. 47.58

CL47 13 Half round welding of [Link] and nuts of towers in the section Each
between ground level & upto bottom X-arm level including all
bolts connecting the bracings at the bottom X-arm level and 21.75
painting the welded portion with one coat of zinc rich paint.
CL48 14 Half round welding of [Link] and nuts of towers in the section Each
between ground level & upto bottom X-arm level including all
bolts connecting the bracings at the bottom X-arm level and 32.63
painting the welded portion with one coat of zinc rich paint- For
JC type towers
CL49 15 Laying of 33 kV 400 [Link] XLPE cable Rmts 354.79
CL50 16 Termination of 400 [Link] XLPE cable Each 6,451.41
CL51 17 Dismantling & re stringing of 33 kV conductor (all types of Per
conductors) for crossing of 33 kV line during stringing of EHT conductor 3,371.15
lines.
CL52 18 Dismantling & re stringing of 11 kV conductor (all types of Per
conductors) for crossing of 11 kV line during stringing of EHT conductor 1,844.61
lines
CL53 19 Dismantling & re stringing of LT conductor/cables for crossing of Per
conductor 1,160.86
LT line (all types) during stringing of EHT lines

10
 File No.ENE51-PM0SYI(400)/12/2021-EE2

ANNEXURE – III
ERECTION OF 400kV SUBSTATIONS
SS Rate for
Item.
[Link]. Description of Item Unit 2020-21
No.
(in Rs)
Total cost of receipt from site/stores, storage, handling,
erection, testing & commissioning of 400/220kV, 315MVA
Transformers 50/ 63/80/125 MVAR Shunt reactor
with all accessories and fittings including storage cum
C4S1 1 erection insurance as per specification. The charges Nos 25,80,242.17
include AC power for oil filter machines and all
other supplier supervision charges including oil testing
charges in a third party lab for complete erection,
testing and commissioning.
Hoisting of insulators & hardware, paving conductor
and stringing of 400kV main bus for three phases with Bus
C4S2 2(a) 44,055.05
quadruple moose conductor to a tension of 1000kgs for Section
single moose conductor, bus section length is 54mtrs.
Hoisting of insulators & hardware, paving conductor
and stringing of 400kV Jack bus for three phases with twin Bus
C4S 3 2(b) 22,344.45
moose conductor to a tension of 1000kgs for single moose Section
conductor, bus section length is 60mtrs.
Erection of 7/3.66 GSS Earth wire from top of peak tower and
LMs to ground and connecting to untreated earth pits
C4S 4 3 including cutting, clamping and fixing of all hardware RM 65.80
like Pad type compression clamp, cleat type clamp and T
clamp etc.
Connecting equipment to equipment through 4"/4.5" IPS
Al tube including cutting, bending, welding, testing,
C4S 5 4(a) Meter 284.00
clamping etc., for each meter including both side
connections.
Connection of equipment to bus and other equipments
4(b) with Quad Moose conductor where ever necessary. Each 1,042.36

Laying of earth mat including excavation & backfilling,

welding, connecting to all equipment, structures,
Junction boxes, and connecting lightning shield to earth
5 mat and earthing of fence posts, drilling and connecting earth
rods including connecting to cast iron pipes as per
approved drawings with the following sizes:
C4S 6 5.1 M.S. Rod 40 mm dia. RM 170.09
Fabrication and connecting to risers from earth mat to
6 structures, equipment, marshalling boxes, electrical
panels, PLCC panels, fencing posts etc.,.
C4S 7 6.1 M.S./ G.S. Flat 75 x 12 mm RM 149.24
C4S 8 6.2 M.S./ G.S. Flat 50 x 8 mm ( Above ground) RM 62.56

11
 File No.ENE51-PM0SYI(400)/12/2021-EE2

Un-Treated Earth pits including installation of 40 mm dia

rod electrode, disconnecting links, and all required
materials and RCC collar/ chambers with bricks, cement
C4S 9 6.3 Each 2,382.86
mortar 1:4 and completion of related civil works as
specified for LMs, LAs, Carrier couplings and CVTs.
(Cost of RCC Collar included)
Laying including termination and providing suitable
ferrules & lugs etc of armoured control cables of size 2 core,
7.0 2.5 [Link] to 27 core, 2.5 [Link] including cost of cable
glands, lugs, ferrules.
C4S 10 7.1 2 to 12 core RM 57.76
C4S 11 7.2 14 to 19 core RM 65.80
C4S 12 7.3 27 core RM 77.03
Laying including termination and providing suitable
ferrules & lugs, jointing kits etc of armoured power
7.4 cables of the following size including cost of cable glands,
lugs, ferrules etc complete.
C4S 13 7.4(a) Upto 50 [Link] RM 99.50
C4S 14 7.4(b) Above 50 [Link] to 300 [Link] RM 126.77
C4S 15 7.4(c) Above 300 [Link] to 700 [Link] RM 160.45
Buried cable trench – Excavation for cable trench
providing 100mm thick sand layer before and after laying
the cable & providing 4” thick brick cover over sand,
8 refilling, consolidation and leveling of surplus earth
including the cost and conveyance of all materials,
route markers, labour charges etc.,complete for finished
item of work.
C4S 16 8.1 Size: 300 X 300 mm RM 276.00
C4S 17 8.2 Size: 300 X 600 mm RM 276.00
C4S 18 8.3 Size: 1500 X 800 mm RM 736.53
Erection of Galvanised cable trays with 2 mm thick
C4S 19 9 RM 65.80
perforated CRCA sheet. Size: 200 and 600mm
Erection of following equipment with
Crane/Derrick at site including handling the
material/equipment carefully at site including labour
charges for all incidental and operational items of
C4S 20 work.(excluding cost of transport charges from Dept.
stores to the site).
Note:- In 400 kV substations only, 25% extra
charges for Testing and Commissioning of switchgear
equipment where ever applicable).
420 KV SF6 Circuit breaker with support structure &
C4S 21 10 Set 26,765.20
marshalling boxes
420 KV Single phase current transformers with secondary
C4S 22 11 Each 7,628.40
terminal box

12
 File No.ENE51-PM0SYI(400)/12/2021-EE2

C4S 23 12 390 KV Lightning Arrestors Each 7,358.83

420kV Single phase Capacitive Voltage
C4S 24 13 transformers with secondary terminal box Each 7,628.40
(with/without carrier coupling device)
400 KV Isolators, 3 pole Horizontal centre
break/Pantograph with Single earth switch including
C4S 25 14.1 Set 15,497.51
solid core insulators, interpole cable laying and
connections for electrical ganging, fixing of MOMs etc.,
400 KV Isolators, 3 pole Horizontal centre break
With Double earth switches including solid core insulators,
C4S 26 14.2 Set 18,597.66
interpole cable laying and connections for electrical
ganging, fixing of MOMs etc.,
220 KV Isolators, 3 pole Horizontal Double
C4S 27 14.3 break/staggered with Double earth switches including Set 10,369.10
solid core insulators, MOMs/BOMs etc.,
C4S 28 15 400 KV Bus post insulators Set 7,358.83
C4S 29 16(a) Erection of Marshalling kiosk Each 1,038.53
C4S 30 (b) Erection of Marshalling boxes Each 504.32
Fabrication of Main and Auxiliary structures, stub setting
templates, foundation bolts, 'U' bolts etc,.using raw steel
C4S 31 17.1 such as [Link], Plates, Channels, [Link], MT 11,376.28
[Link], excluding cost of Mild Steel and transport
charges to substation site.
Galvanization of Main and Auxiliary structures, stub setting
templates, foundation bolts, 'U' bolts etc,.using raw steel
such as [Link], Plates, Channels, [Link],
C4S 32 17.2 [Link], excluding cost of zinc and transport charges to MT 6,660.75
substation site.(Cost of zinc should be followed as per
IEEMA rates.).The average quantity of Zinc required for all
angles of tower parts is 60 Kgs.

13
 File No.ENE51-PM0SYI(400)/12/2021-EE2

ANNEXURE - IV
ERECTION OF 220kV, 132 kV & 33kV SUBSTATIONS
SS Rate for
Sl. Item 2020-21
Description of Item Unit
No. No. (in Rs)

CS1 1 Hoisting of Insulators and hardware, stretching the conductor Bus

and stringing of 220 kV bus comprising of three phases with Section
Quadraple Moose conductor to a tension of 900kgs for single 27,801.15
moose conductor.( The maximum length or up to a length of
bus section of 40m)
CS2 2 Hoisting of Insulators and hardware, stretching the conductor Bus
and stringing of 220 kV bus comprising of three phases with Section
6,951.64
single Zebra/Moose conductor to a tension of 900kgs.( The
maximum length or up to a length of bus section of 40m)
CS3 3 Hoisting of Insulators and hardware, stretching the conductor Bus
and stringing of 220 kV bus comprising of three phases with Section
Twin Zebra/Moose conductor to a tension of 1800kgs , 13,906.01
including fixing of spacer clamps( The maximum length or up to
a length of bus section of 40m).
CS4 4 Hoisting of Insulators and hardware, stretching the conductor Bus
and stringing of 132 kV bus comprising of three phases with Section
6,951.64
Single Zebra/Moose conductor to a tension of 900kgs.( The
maximum length or up to a length of bus section of 45m).
CS5 5 Hoisting of Insulators and hardware, stretching the conductor Bus
and stringing of 132 kV bus comprising of three phases with Section
Twin Zebra/Moose conductor to a tension of 1800kgs including 13,906.01
fixing of spacer clamps.( The maximum length or up to a length
of bus section of 45m).
CS6 6 Hoisting of Insulators and hardware, stretching the conductor Bus
and stringing of 33 kV bus comprising of three phases with Section
5,215.78
Single Zebra/Moose conductor to a tension of 450kgs.( The
maximum length or up to a length of bus section of 20m).
CS7 7 Hoisting of Insulators and hardware, stretching the conductor Bus
and stringing of 33 kV bus comprising of three phases with Section
Twin Zebra/Moose conductor to a tension of 900kgs including 8,694.31
fixing of spacer clamps.( The maximum length or up to a length
of bus section of 20m).
CS8 8 Hoisting of Insulators and hardware, stretching the conductor Bus
and stringing of 132 kV bus comprising of two phases with Section
4,632.61
Single Zebra/Moose conductor to a tension of 900kgs.( The
maximum length or up to a length of bus section of 45m).
CS9 9 Fixing of spacers for Twin Moose conductor Each 137.29
CS10 10 Fixing of spacers for Quadruple Moose Conductor Each 190.30
CS11 11 Fixing of Hardware,stretching the ground wire and stringing of Each
1,038.53
earth wire to a tension of 450kgs from pinacle to pinacle.
CS12 12 Fixing of Hardware,stretching the ground wire and stringing of RM
70.68
earth wire to a tension of 450kgs from pinacle to ground.
CS13 13 Connection of equipment to bus and or another equipment with Each
single zebra/Moose/Panther conductor including measuring,
364.30
cutting,clamping and hoisting of suspension insulator assembly
to support the conductor wherever necessary.
CS14 14 Connection of equipment to bus and or another equipment with Each
Twin zebra/Moose/Panther conductor including measuring,
564.13
cutting,clamping and hoisting of suspension insulator assembly
to support the conductor wherever necessary.
CS15 15 Connection of equipment to bus and or another equipment with Each
Quad zebra/Moose/Panther conductor including measuring,
1,129.60
cutting,clamping and hoisting of suspension insulator assembly
to support the conductor wherever necessary.

14
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate for
Sl. Item 2020-21
Description of Item Unit
No. No. (in Rs)

16 Laying of earth mat including excavation of trenches, welding,

connecting to equipment and connecting lightning shield to earth
mat and earthing of fence posts, drilling and connecting earth
rods including connecting cast iron pipes as per Drg.
[Link](P)/149/82 with the following sizes of MS Flats /GI
Flats.(for 220kV & 132kV) including fabrication.
CS16 16 a 100x16mm MS Flat / GI Flat. RM 107.40
CS17 16 b 50x 8mm MS Flat / GI Flat. RM 84.27
CS18 16 c 75x 8mm MS Flat / GI Flat. RM 96.52
CS19 16 d For laying of earth flat in hard rock in substation / bays RM
extension, an additonal amount to the basic labour rate of SSR
73.40
will be allowed as there is no provision in the rate of laying of
earth flat for remvoal of hard rocks.
CS20 17 Excavation of earth pit, putting cast iron pipe with flange on one Each
end (as per ISS7181/86) of nominal dia 125mm and 2.75 meters
long in side the pit including supply and fixing RCC collars 0.75
meter dia (OD), 50mm thick and 0.60meters long in side the pit,
backfill the pit in the 25mm size granules of BHcoke for full
depth of the pit with alternate layers of BH coke and salt of 15,499.16
300mm thick around the earth pipe of 150mm on all the sides of
the pipe including cost and conveyance of BH coke, salt, clamps,
[Link] and RCC collars, labour charges for all operational and
incidental items of work etc., complete.
CS21 18 Laying of control cables of all sizes (from 2 core. 2.5 / 4.0sqmm RM
to 12 core, 2.5/4.0sqmm , both copper and alluminium in cable
trenches including cost of suitable metalic cable glands with
12.23
rubber lining. Note: This includes running of cables in control
room where cables are run on cable racks in cable duct.

19 Laying of power cables.

CS22 19 a upto 50 sqmm RM 16.31
CS23 19 b above 50 sqmm RM 21.75
20 Cable terminations to the switchgear, Marshalling boxes / Panel
terminal blocks/control & relay panels, LTAC panel including
providng suitable ferrules and lugs as per specification (including
cost of ferrules and lugs) (for 220kV & 132kV).
CS24 20 i 2.5 sqmm Copper with copper lugs each core at both ends. Nos. 36.71
CS25 20 ii 4.0 sqmm Aluminium with Aluminium lugs each core at both Nos.
39.44
ends.
CS26 20 iii Up to 50 sqmm Power Cable with lugs each core at both ends. Nos.
85.65
CS27 20 iv Above 50 sqmm Power Cable with lugs each core at both ends. Nos.
156.34
CS28 21 Instalation of lighting fixtures on switch yard structures Each
including cabling and connections, labour charges etc., including
40mm dia G.I bent pipe of 0.75m length with suitable clamps for 1,391.95
fixing to structures in complete shape (excluding cost of lighting
fixtures)
22 Erection of the following equipment with Crane / Derrick at site
including handling the material / equipment carefully at site
including labour charges for all incidental and operational items
of work. (excluding cost of transport charges from Dept. stores to
the site).
CS29 22.1 220 kV Circuit breakers with support structure & marshalling Each
boxes including grouting of foundation bolts and wiring of 24,334.84
cables from Ploe to Pole including terminations.
CS30 22.2 132 kV Circuit breakers with support structure & marshalling Each
17,385.90
boxes including Ploe to Pole cable wiring and terminations.
CS31 22.3 33 kV Circuit breakers including Ploe to Pole cable wiring and Each
7,006.02
terminations.

15
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate for
Sl. Item 2020-21
Description of Item Unit
No. No. (in Rs)

CS32 22.4 2-pole 220 kV Circuit Breaker with support structure & Each
marshalling boxes incl. grouting of foundation bolts & wiring of 20,683.65
cables & terminations.
CS33 22.5 2-pole 132 kV Circuit Breaker with support structure & Each
marshalling boxes incl. grouting of foundation bolts & wiring of 14,777.34
cables & terminations.
CS34 22.6 220 kV Current Tranformers. Each 5,913.11
CS35 22.7 132 kV Current Tranformers. Each 3,823.81
CS36 22.8 33 kV Current Tranformers. Each 1,181.28
CS37 22.9 220 kV Potential Transfomers. Each 5,913.11
CS38 22.10 132 kV Potential transformers. Each 3,823.81
CS39 22.11 33 kV Potential transformers. Each 1,181.28
CS40 22.12 220 kV Lightning Arrestors. Each 3,823.81
CS41 22.13 132 kV Lightning Arrestors. Each 1,805.20
CS42 22.14 33 kV Lightning Arrestors. Each 705.49
CS43 22.15 220 kV Capacitve Voltage Transformers. Each 5,563.77
CS44 22.16 132 kV Capacitve Voltage Transformers. Each 3,823.81
CS45 22.17 220 kV Isolators with earth swtich including solid core insulators Each
erection, alignment in full shape for smooth operation by 9,387.56
Electrical and manually.
CS46 22.18 132 kV Isolators with earth swtich including solid core Each
insulators erection, alignment in full shape for smooth operation 6,951.64
by manually.
CS47 22.19 220 kV Isolators without earth swtich including solid core Each
insulators erection, alignment in full shape for smooth operation 8,694.31
by Electrical and manually.
CS48 22.20 132 kV Isolators without earth swtich including solid core Each
insulators erection, alignment in full shape for smooth operation 6,254.30
by manually.
CS49 22.21 2-pole, 220 kV Isolators without earth swtich including solid Each
core insulators erection, alignment in full shape for smooth 7,389.35
operation by Electrical and manually.
CS50 22.22 2-pole, 132 kV Isolators without earth swtich including solid Each
core insulators erection, alignment in full shape for smooth 5,316.38
operation by Electrical and manually.
CS51 22.23 33 kV Isolators including solid core insulators erection, Each
2,259.21
alignment in full shape for smooth operation.
CS52 22.24 220 kV Bus Post Type Insulators. Each 492.08
CS53 22.25 132 kV Bus Post Type Insulators. Each 371.10
CS54 22.26 33 kV Solid Core Insulators Each 248.76
CS55 23 33 kV /400 V Station Transformer including all necessary Each
connections on HV & LV side including cost of lugs (But 7,852.89
excluding cost of transformer and HG fuse set)
CS56 24 Erection of Control / Relay panels, LTAC panels, announciation, Each
PTDB panels etc.,in the control room duly mounting them on
channels and grouting them with foundation bolts excluding cost
3,088.41
of channels & foundation bolts (for 220kV & 132kV),
including man power support to MRT wing for commissioning.

CS57 25 Erection of 220 V, 200 Ah/ 80 Ah Lead Acid battery in complete Set
12,103.53
shape fit for charging.
CS58 26 Erection of 220 V, 200 Ah/ 80 Ah maintenance free battery in Set
3,912.17
complete shape fit for charging .
CS59 27 Erection of 220 V, 200 Ah / 80Ah battery charger. Set 4,022.28
CS60 28 Erection of Capacitor Bank including series reactor of 7.5 Each
6,233.92
MVAR Capacity
CS61 29 Erection of Marshalling kiosk Each 1,038.53
CS62 30 Erection of Marshalling boxes Each 504.32
CS63 31 Erection of Lighting pillar box in switchyard on foundation laid Each
1,390.59
(Excluding pillar box). (for 220kV & 132kV )

16
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate for
Sl. Item 2020-21
Description of Item Unit
No. No. (in Rs)

CS64 32 Fabrication of Main and Auxiliary structures, stub setting MT

templates, foundation bolts, 'U' bolts etc,.using raw steel such as
11,376.28
[Link], Plates, Channels, [Link], [Link],
excluding cost of Mild Steel and transport charges to site.
CS65 33 Galvanization of Main and Auxiliary structures, stub setting MT
templates, foundation bolts, 'U' bolts etc,.using raw steel such as
[Link], Plates, Channels, [Link], [Link],
excluding cost of zinc and transport charges to substation 6,660.75
site.(Cost of zinc should be followed as per IEEMA rates.).The
average quantity of Zinc required for all angles of tower parts is
60 Kgs.
34 Setting of stubs with stub setting template for sub-station
structure:Erection of stub template, fixing of jacks for supporting
the template, alignment and leveling of exact location of stubs of
stubsetting template, dismantling of template after completion of
initial curing of CC
CS66 34.1 220kV Towers Set 4,488.54
CS67 34.2 132kV Towers Set 3,222.98
CS68 34.3 33kV Towers & CPL's Set 804.73
CS69 34.4 220kV Isolator Set 3,367.07
CS70 34.5 132kV Isolator Set 2,416.89
CS71 34.6 220 kV Breaker Set 2,911.71
CS72 34.7 132 kV Breaker Set 2,183.08
CS73 34.8 33 kV Breaker Set 1,455.84
CS74 35 Erection of the main and auxiliary structures etc., using bolts and MT
nuts. 3,477.17

CS75 36 Fixing of 90lb rail poles over the transformer plinths. RM 691.90
CS76 37 Fixing of 105lb rail poles over the transformer plinths. RM 808.80
CS77 38 Erection of 33kV HG Fuse set Each 840.07
CS78 39 Erection of 33kV PT Distribution Box Each 505.67
CS79 40 Laying and Terminations of 11kV, XLPE 1000 Sqmm Cable RM 176.72
CS80 41 Erection of 11kV VCB outdoor type Kisok (within built Breaker, Each
3,591.37
CTs, PTs, Surge Arrestors & Relays).
Marking as per approved layout with the help of surveyor
CS81 42 220 kV sub-station Each 43,667.31
CS82 43 132 kV sub-station Each 29,111.54
CS83 44 Bay / Bays in one sub-station Each 14,555.77
45 Auto-CADD drawing with 12 copies indicate complete land with
dimensions, plan of SS with equipments, location of control
room, equipments, roads, duct routes, earth mat of 100X16mm &
50X 8mm flat earth pits,yard lighting fixtures etc.,
CS84 i 132kV SS layout drawing Job 7,394.79
CS85 ii 220kV SS layout drawing Job 9,073.58
CS86 46 Writing of letters in control room panels of lettering on panels Line
104.67
marshalling boxes.
CS87 47 Supply and installation of Key - Board of size 1.5'x2' of Eco Each
Wood Board with Glass covering with lock and key arrangments 5,817.94
for providing all the keys of equipment and SS.
Note:
i. Bore earthing in estimations as per field conditions will be considered on
case to case basis as supplemental items.
ii. 25% excess over CS64 is allowed for JC tower fabrication charges.

17
 File No.ENE51-PM0SYI(400)/12/2021-EE2
ANNEXURE – V
ERECTION OF ILLUMINATION, LIGHTING, FIRE FIGHTING,AIRCONDITIONING,
D.G Set & 33kV STATION SUPPLY SYSTESM IN 400kV SUBSTATIONS.
SS Rate for
Sl. Item. 2020-21
Description of item Unit
No. No. (in Rs)
Erection of indoor and outdoor illumination for 400/220 KV
Substation, Control House, Auxiliary Buildings, 33 KV Switch yard,
street lighting, erection and commissioning of following items as per
C4F1
the approved design and drawings, including indoor/ outdoor
Junction Boxes, Conduits, Lighting wires, lugs, ferules etc for
complete finished item of work.
Fixing Buzzer anchor make or equivalent approved make with ISI
1 Each 312.91
mark with necessary bell and switches etc.
Providing and fixing concealed in roof and walls with PVC Conduit
piping of ISI standards with necessary GI wire of of suitable guage
to draw wires at later date including cost of junction Box etc. cost of
2 conveyance of all materials etc complete for finished item of
work for Guest House, store building, pump house building &
C4F 2 security room as approved and directed by the Engineer- in-charge
at site.
(i) 32 mm dia - 2mm thick RM 125.17
(ii) 25 mm dia - 2 mm thick RM 109.13
(iii) 12 mm dia - 1.5mm thick RM 73.81
Modular for Main distribution board with 1 No. 63A, TPMCB for
I/C and 2 Nos. 32A SPMCB &
C4F 3 3 Each 2,283.41
6 Nos. SPMCB with neutral link for O/G complete make
Havells or MDS or equivalent.
Fixtures for 36W lamps BJLM-236 type, Fixtures for 36W lamps BJSM-
3(i) 236 type , Fixtures for 36W lmaps BJIV-236 type, Fixtures for energy Each 624.18
saving tube light 2x36W or equivalent LED lamps.
Fixtures for 9W CFL Lamp, Fixtures for GLS DBD-10type,
3(ii) Fixtures for 2x18 W CFL Lamp, Fixtures for 1x36W CFL Lamp or Each 312.91
equivalent LED lamps.
Erection, testing and commissioning of outdoor and street Lighting
C4F 4 4 Fixtures including fixing of conduit, Junction boxes, wiring and
terminations complete etc.(excluding cost of concrete)
Lighting Masts / Poles as per drawing enclosed
1
including concreting in full shape.
(i) Type A1 Each 6,418.51
(ii) Type E1 Each 3,429.09
(iii) All types of Lighting Panels Each 2,203.16
Junction Box with MCB and Terminal Blocks
(iv) Each 436.46
(Bolt Type)
(v) 415V 63A Power Recepticle outdoor Each 872.94
(vi) 5/15 A, 240 V sockets with swtich board Each 57.76
(vii) Decorative type switch Boards Each 125.17
(viii) Telephone Junction Boxes Each 109.13
(ix) Telephone Jacks for Telephones Each 40.12
(x) Celling Fans with Electronic regulators Each 221.44
Flood lighting fixtures for 400W sodium Vapour
(xi) Each 409.18
lamp or Equivalent LED Lamp

18
 File No.ENE51-PM0SYI(400)/12/2021-EE2
SS Rate for
Sl. Item. 2020-21
Description of item Unit
No. No. (in Rs)
Street lighting fixtures for 150 W sodium Vapour lamp or Equivalent
(xii) LED Lamp Each 409.18

Street lighting fixtures for 250 W sodium Vapour lamp or Equivalent

(xiii) LED Lamp Each 492.62

Industrial high bay lightining fixtures for

(xiv) 250 W HVSP lamp or Equivalent LED Lamp Each 492.62

Lighting fixtures for 125 HP MV lamp post

(xv) Each 306.49
lanterns or Equivalent LED Lamp
Erection, testing and commissioning of Fire Fighting,
C4F 5 Detection and Alarm System :
Erection of Horizontal centrifugal Electric Driven Hydrant/HVW
Spray pump of capacity 410 Cum/hr, total dynamic head of 88MWC
1 with all accessories & fittings and Electric Induction Motor Squirrel Each 79,103.35
cage type for the above with all accessories & fittings.
Erection of Horizontal centrifugal Diesel Engine Driven
Hydrant/HVW spray pump of capacity 410 Cum/hr and total dynamic
head of 88MWC with all accessories and fittings. Diesel Engine,
2 multi cylinder type, four stroke cycle with mechanical airless Each 84,031.16
injection cold starting type for the above with all accessories and fittings
and a set of Batteries and battery chargers and fuel tank having
capacity to hold fuel oil for six hours of full load run.
Erection of Horizontal centrifugal Electric Driven jockey pump of
capacity 10.8 Cum/hr and Total dynamic head of 88MWC with all
3 Each 7,501.63
accessories and fittings along with Electric Motor for the above with all
accessories and fittings.
4 Air vessels with vent valves etc. as per system requirement. Each 6,508.37
Sump pumps 10 Cum/ Hr. MWC with motor
5 Each 5,755.81
starter and all accessories
6 Basket strainer 300 NB Each 2,500.00
Control panel equipped with all accessories for motor drives of Fire
7(a) water pumps and 2 Nos. jockey pumps for two sources of supply. Each 5,001.63
C4F6
Panel for 2 nos. Battery chargers & Diesel Engine
7(b) Each 5,001.63
driven fire water pumps.
Annunciation panel at fire water pump
7(c) Each 1,906.29
house.
7(d) Annunciation panel in Control Room. Each 1,906.29
8 Hydrant and HVWS system Accessories.
C4F 7
(a) Single headed Hydrants Each 872.94
(b) Landing valves Each 872.94
(c) Hose cabinets. Each 953.14
(d) Hoses of 15.0m length with coupling Each 86.65
(e) Hoses of 7.5m length with coupling Each 86.65
(f) Branch pipe with Nozzles. Each 86.65
Mild steel black pipes and Galvanized Mild steel pipes with wrapping &
coating for below ground and painting for above ground including cost
C4F8 9 of wrapping & coating material and paint required & excavation, back
filling & all civil works etc., & testing complete.
a(i) 300 NB (below ground) RM 2,500.00

19
 File No.ENE51-PM0SYI(400)/12/2021-EE2
SS Rate for
Sl. Item. 2020-21
Description of item Unit
No. No. (in Rs)
a(ii) 300 NB (above ground) RM 1,667.20
b(i) 250 NB (below ground) RM 2,044.30
b(ii) 250 NB (above ground) RM 1,290.12
c(i) 200 NB (below ground) RM 1,586.97
c(ii) 200 NB (above ground) RM 1,211.50
d(i) 150 NB (below ground) RM 1,251.61
d(ii) 150 NB (above ground) RM 1,022.16
e(i) 100 NB (below ground) RM 794.28
e(ii) 100 NB (above ground) RM 645.06
f(i) 80 NB (below ground) RM 604.93
f(ii) 80 NB (above ground) RM 417.20
g) 50 NB RM 404.36
h) 25 NB RM 242.30
i) 15 NB RM 171.70
Set of GI Piping beyond deluge valves for transformer including
10(a) detection piping and pipe supports including all accessories. per Set 2,84,869.63
C4F 9
10(b) Erection of Hume pipe as per specification. RM 794.28
11 VALVES
C4F10
(a) 300 NB Gate Each 2,500.00
(b) 250 NB Gate Each 2,122.94
(c) 250 NB Check Each 2,122.94
(d) 200 NB Gate Each 1,667.20
(e) 150 NB Gate Each 1,586.97
(f) 100 NB Gate Each 1,129.66
(g) 80 NB Gate Each 754.18
(h) 80 NB Check Each 754.18
(i) 25 NB Gate Each 276.00
(j) 50 NB Gate Each 604.93
(k) 50 NB Check Each 604.93
(l) 15 NB Each 166.89
(m) Float operated valve 100 NB Each 1,586.97
C4F11 12 INSTRUMENTS
(a) Float operated level gauge Each 1,370.36
(b)Level Switch Each 1,370.36
(c)Pressure Gauge Each 794.28
(d)Pressure Switch Each 1,667.20
(e)Differential Pressure Gauge Each 1,211.50
Deluge valve with motor gounge, [Link], [Link], solenoid valve to
C4F12 13(a) drain - size 150 NB set 7,501.63

13(b) Local control panel for Deluge valve Each 2,122.94

13(c) Strainer Y type, 150 NB Each 1,667.20
13(d) Quartzoid bulb detectors Each 134.80
13(e) HVW spray nozzles Each 134.80

20
 File No.ENE51-PM0SYI(400)/12/2021-EE2
SS Rate for
Sl. Item. 2020-21
Description of item Unit
No. No. (in Rs)
C4F13 14 Detection & Alarm System
(a) Ionization smoke detector Each 604.93
(b) Photoelectric smoke detector Each 604.93
(c) Heat detector Each 604.93
(d) Response indicator Each 604.93
(e) Manual call point Each 604.93
(f) Fire detection & Alarm panel Each 604.93
C4F14 15 Portable Fire Extinguishers
Dry chemical powdertype Fire
(a)
extinguishers with all accessories.
(i) 10 kgs. Capacity Each 60.98
(ii) 25 kgs. Capacity (trolley mounted) Each 120.35
(iii) 50 kgs. Capacity (trolley mounted) Each 162.06
(iv) 150 kgs. Capacity (trolley mounted) Each 346.62
(b) CO2 type portable Fire extinguishers
(i) 45 kgs. Capacity (trolley mounted) Each 125.17
(ii) 22.5 kgs. Capacity (trolley mounted) Each 125.17
(iii) 9 kgs. Capacity (trolley mounted) Each 59.37
(iv) 2 kgs. Capacity (Portable ) Each 46.53
(c) 9 Litres capacity Mechanical foam type fire Each 62.56
(d) extinguishers
Sand / water Buckets 9 litres capacity Each 81.84
C4F15 16 Air Conditioning System
Erection, testing and commissioning of Split AC 2 Ton with all
1 suitable accessories Each 5,938.72

Erection of Air Conditioning AC distribution

2 Each 5,001.63
panel
Providing Under Deck Insulation for the Roof exposed to sunlight with
50 mm thick TF Sq.
3 quality expanded poly styrene including GI washers and wire for 54.55
ft.
fixing.
4 Erection of Ventilation fans
i) 600 mm Sweep Each 1,330.24
ii) 450 mm Sweep Each 1,330.24
iii) 300 mm Sweep Each 1,330.24
Erection, testing and commissioning of 250 KVA DG Set complete
C4F16 17 including AMF Panel, Set 88,597.93
auxiliaries etc.
Erection, testing and commissioning of 33kV
C4F17 18
Station Supply System
1 33kV/440 V Substation :
33kV/433 V, 630KVA Station supply
(a) Each 7,588.29
transformer
33 kV Isolator with terminal connectors and
(b) Set 2,259.21
support insulators
(c) 33 kV HG Fuse set Each 840.07
(d) 33 kV Lightning Arrestor Each 705.49
(e) 150 x 75 mm M.S Channels &Struc. MT 3,201.24
(f) HT Trivector Meter Box Each 953.14

21
 File No.ENE51-PM0SYI(400)/12/2021-EE2
SS Rate for
Sl. Item. 2020-21
Description of item Unit
No. No. (in Rs)
Hoisting of Insulators & Hardware, stringing / formation of the
33 kV Bus comprising of 3 phases with DOG Conductor and all
equipment to equipment, equipment to bus interconnections,
(g) LS 17,469.59
jumpering, fixing of clamps & connectors etc. required for the
entire 33kV/440 V station supply switchyard of 400/220 KV
Substation complete as directed by site engineer.
2 33 kV Line :
Erection of pole in position, aligning and setting to work, fixing of cross
arms and top clamps, earthing of supports, fixing of danger boards,
(a) back filling with earth and stones properly ramming including Set 2,023.44
transport of materials from road side to location excluding
concreting and including excavation.
Assembly and erection of [Link] as per specification
which includes fixing of top channels and cross bracings, transport
(b) of all materials from road side to the location, earthing, back filling Set 3,241.35
with earth ramming etc excluding concreting and including
excavation.
Mass concreting of supports erected with CC ([Link]) using 40 mm,
(c) Cum 6,102.41
HBG metal including the cost of metal, sand, cement and curing etc.
Assembly and erection of stay set including fixing of guy insulators,
clamps etc., on the pole and fixing stay wire and binding securely on
(d) either side as per standards, transport of material from road side to Set 405.97
location and back filling with earth ramming etc excluding
concreting and including excavation.
Paving out conductor, providing temporary stays, tensioning, sagging
correctly, fixing strain points, transferring to pin points
(e) binding, fixing of Insulators, guys and jumpering etc., km 14,847.64
including transport of material from road side to location.
( 3phases)
19 Erection of Control and Relay Panels
Receipt from site stores, Transport to control room, handling, Erection,
C4F18 Testing and commissioning of all Control, Relay, Protection and
other Panels/ Equipment, with complete accessories, equipment etc.,
as specified.
400 KV Feeders/ Tie/ 315 MVA Transformer Control/ Relay/
(i) Protection Panels. Each 41,779.71

220 KV Feeders/ Bus coupler/ Transfer Bus / 315 MVA

(ii) Transformer / 50/63/80MVAR/125 MVAR Shunt Reactors Control/ Each 39,791.58
Relay/ Protection Panels.
(iii) Common equipment panels for 400/220kV Each 34,337.43
(iv) 400kV Bus bar Protection Set 53,929.96
(v) 220KV Bus bar Protection Set 69,626.43
C4F19 19(i) Common equipment Panels for 400/220kV. Each 34,337.43
All other equipment of SMS and Time
19(ii) Each 1,59,798.50
synchronizing equipment.
19(iii) 400KV AC Bay Kiosk Each 40,454.30
19(iv) 220KV AC Bay Kiosk Each 30,341.92
Complete Substation Automation system for 400/220KV
Substation including hard ware and software for remote control
C4F20 20 station along with associated equipments and kiosks infull shape
as perspecification.

22
 File No.ENE51-PM0SYI(400)/12/2021-EE2
SS Rate for
Sl. Item. 2020-21
Description of item Unit
No. No. (in Rs)
Installation, Testing and commissioning of Networking Panel,
(a) OWS1, OWS2, EWS Remote work station. BCUs, LIUs, Set 2,61,069.82
Ethernet Switches, Splicing of OFC etc.,
Installation, Testing and commissioning of all necessary
software’s compatible to IEC: 61850 for making the SAS operation in
(b) Set 87,023.81
full shape including remote SCADA complete as directed by site
engineer.
Extension works of Installation, Testing and commissioning of
(c) BCU, LIU, Ethernet Switch,
Splicing of OFC to the existing SAS System.
Per bay
(if it is
(I) FIRST BAY 34,809.20
First
Bay)
(ii) SECOND BAY onwards Per Bay 17,405.39
Extension works of Installation, Testing and commissioning of
all necessary software’s compatible to IEC: 61850, adding new
(d) SLD for the new bay in the existing substation and configuring
all necessary signals and data base for making the SAS operation in full
shape including Remote SCADA as directed by site engineer.
Per bay
(I) FIRST BAY (if it is 87,023.81
First
(ii) SECOND BAY onwards Per Bay 43,511.10
220 V DC Battery & Battery Chargers and AC, DC Distribution Boards

Receipt from site stores, Transport to control room, handling

1 Erection, Testing and commissioning of Battery & Battery chargers
with complete accessories, equipment etc.,as specified.
220V, 400AH Capacity Sealed Maintenance free VRLA Type 1 No
(a) Battery Banks along with all other required accessories. Set 14,683.93

(b) 40/100A Float - Cum- Boost Charger (1 No.) Set 8,735.59

Receipt from site stores, Transport to control room, handling,
2 Erection, Testing and commissioning of A.C.& [Link]
Boards with complete accessories, equipment etc., as specified.
415V AC Main Board (Sub-Boards- I &
(a) Each 1,18,772.99
II) as per the Specification & Drawing.
415V AC Distribution Board (Sub- Boards- I &
(b) Each 1,97,959.76
II) as per the Specification & Drawing.
415V AC Lighting Board (Sub- Boards- I & II ) & Emergency
(c) Lighting Board as per the Specification & Drawing. Each 49,729.04

220V DC Distribution Board (Sub-Boards- I & II) as per the

(d) Each 29,996.94
Specification & Drawing.

23
 File No.ENE51-PM0SYI(400)/12/2021-EE2

ANNEXURE -VI
Loading / Unloading of materials from departmental / Private
I
vehicles in to the stores yard and stacking and vice-versa
SS Rate for 2020-21
Item (in Rs)
Sl. No. Description of Item Unit
No. Un
Loading
Loading
ST1 I Cement MT 124.93 145.59
2 All other materials
ST2 (i) Steel MT 283.56 283.56
ST3 (ii) Tower parts MT 283.56 283.56
ST4 (iii) RS Joists and rail poles and MS MT 283.56 283.56
Sheets pf various sizes.
3 Cable / Conductor drums (for loading
/ un loading )
ST5 a Panther ACSR Each Drum 311.98 311.98
ST6 b Zebra ACSR Each Drum 436.62 436.62
ST7 c Moose ACSR Each Drum 436.62 436.62
ST8 d Moose ACSR (Huge Drums of Each Drum 641.89 641.89
1.75KM and above)
ST9 e Earth wire Each Drum 187.04 187.04
ST10 f Control cables up to 6 Core Each Drum 187.04 187.04
ST11 g Control cables above 6 Core Each Drum 249.44 249.44
ST12 h 3 1/2 Core LTAC cable drum (up to Each Drum 249.44 249.44
500 meters).
ST13 i 3 1/2 Core LTAC cable drum (above Each Drum 311.98 311.98
500 meters).
4 Other materials received in cases.
ST14 (i) Case weighing not more than Each case 164.47 164.47
100kgs.
ST15 (ii) Case weighing from101kgs to Each case 310.05 310.05
500kgs.
ST16 (iii) Case containg fragile items and Each case 620.25 495.35
weighing more than 501kgs and up
to 1MT
ST17 (iv) for LTAC panel Each 413.93 413.93
ST18 v(a) 70KN Normal disc insulator Each 1.62 1.62
ST19 v(b) 120KN Normal disc insulator Each 2.05 2.05
ST20 v(c) 160KN Normal disc insulator Each 2.44 2.44
ST21 vi(a) 70KN Anti-fog disc insulator Each 2.05 2.05
ST22 vi(b) 120KN Anti-fog disc insulator Each 2.44 2.44
ST23 vi(c) 160KN Anti-fog disc insulator Each 3.27 3.27
(vii) Loading / Un loading and stacking
charges for 70KN /120KN SRC
insulators.
ST24 (a) 132kV Each string 3.27 3.27
ST25 (b) 220kV Each string 4.08 4.08

24
 File No.ENE51-PM0SYI(400)/12/2021-EE2

ST26 (viii) Loading / Un loading and stacking Each string 4.77 4.77
charges for 120KN /160KN SRC
insulators for 400kV .
5 Cases containing Control & Relay
Panels
ST27 (a) 33kV Each 413.93 413.93
ST28 (b) 132kV and 220kV Each 516.00 516.00
6 Cases containing CTs, PTs, CVTs 0.00
ST29 (i) 11kV to 33kV Rating Each case 92.79 92.79
ST30 (ii) Above 33kV and up to 132kV Each case 623.67 623.67
ST31 (iii) 220kV Rating Each case 930.06 930.06
7 Cases containing LAs
ST32 (i) 33kV Each case 16.45 16.45
ST33 (ii) 132kV Each case 310.05 310.05
ST34 (iii) 220kV Each case 413.93 413.93
8 Loading / Un-Loading of
ST35 1 33kV Breaker Each set 763.45 763.45
ST36 2 132kV CB Each set 2,478.60 2,478.60
ST37 3 220kV SF6 CB Each set 3,096.70 3,096.70
ST38 4 Station Transformer (100KVA) Each set 475.76 475.76
ST39 5 Station Transformer (250KVA) Each set 569.97 569.97
ST40 6 220V 80AH Battery (Conventional) Set 1,032.27 1,032.27
(Lead Acid)
ST41 7 220V 80AH Battery (VRLA) Set 723.97 723.97
(Maintenance Free)
ST42 8 220V 200AH Battery Set 1,134.36 1,134.36
(Conventional) (Lead Acid)
ST43 9 220V 400AH Battery Set 1,652.40 1,652.40
ST44 10 220V Battery Charger with DC Set 620.25 620.25
distribution Board
ST45 11 DCDB for battery Charger. Each 206.08 206.08
ST46 12 132kV Hardware single Set 14.54 14.54
ST47 13 132 KV Hardware double Set 15.08 15.08
ST48 14 220 kV Hardware single Set 20.53 20.53
ST49 15 220 KV Hardware double Set 21.89 21.89
ST50 16 220 KV Isolators, without insulators Set 620.25 620.25
including machanism box
ST51 17 220kV Solid core insulators Each 83.06 83.06
ST52 18 132 KV Isolators (without soild core Each 465.03 465.03
insulators)
ST53 19 132kV Solid core insulators Each 51.11 51.11
ST54 20 33 KV Isolators (without soild core Each 206.08 206.08
insulators)
ST55 21 33kV Solid core insulators Each 5.86 5.86
ST56 22 Vibration dampers, mid span 100 Nos 206.08 206.08
compression joints, repair sleeves,
clamps & connectors etc
23 Capacitor Banks

25
 File No.ENE51-PM0SYI(400)/12/2021-EE2

ST57 a 5 MVAR Set 1,652.40 1,652.40

ST58 b Neutral C.T. Each 113.37 113.37
ST59 24 Scrap items like MS Scrap, GI Scrap, Per MT 310.05 310.05
Ferrous Scrap etc,.
ST60 25 Scrap items like Conductor scrap, Per MT 413.93 413.93
Earth wire Scrap, etc,.
ST61 26 Bolts & Nuts weighing 50 Kgs bags Each bag 9.50 9.50
including springs washers, flat
washers.
ST62 27 3 1/2 Core LTAC Cable bits (loose) Mts 0.95 0.81
by measuring and load / unload (up
to 500 Meters, limited to Rs.142 per
Bit (Maximum)
ST63 28 Cable bits (loose) up to 6 Core by Mts 0.81 0.81
measuring and load / un load.( up to
500 Meters, limited to Rs.106 per Bit
(Maximum)
ST64 29 Cable bits (loose) above 6 Core by Mts 1.36 1.36
measuring and load / un load.(up to
500 Meters, limited to Rs.142 per Bit
(Maximum)
ST65 30 Copper Scrap Per MT 247.54 247.54
ST66 31 Battery Scrap Per MT 258.95 258.95
ST67 32 Capacitor units Scrap Each 11.14 11.14
ST68 33 33kV Breaker Limb Each 209.07 209.07
ST69 34 132kV Breaker Limb Each 516.00 516.00
ST70 35 220kV Breaker Limb Each 742.88 742.88
ST71 36 Tyres scrap of all sizes Each 24.74 12.51
ST72 37 Empty oi drums Barrel 4.64 4.64
ST73 38 Full oil drums Barrel 52.72 52.72
ST74 39 220V, 200AH Battery (VRLA) Set 794.26 794.26
(Maintenance free)
ST75 40 220kV Bushing Each 320.94 320.94
ST76 41 132kV Bushing Each 160.40 160.40
ST77 42 33kV Bushing Each 40.22 32.07

Note: - If loading / Un loading is done with Crane, 1/3 rd Charges are to be paid
towards labour chargesand remaining amount is towards crane hire
[Link]: Loading charges of 100 kVA Station Transformer is Rs. 416.49
and in case is loaded by using a crane then labour charges would be Rs.138.83 &

Loading and Un loading and counting at Stores for check measuring and Stock
II.
Verificaiton Purpose
SSR for
Item
Sl. No. Description of Item 2020-
No.
21(Rs.)
ST78 43 Tower parts counting on part wise and restocking at 103.98
stores yard ( for stock verification purpose)

26
 File No.ENE51-PM0SYI(400)/12/2021-EE2

ST79 44 Labour charges for weighing and restocking of GI 413.93

Tower Parts or Bolts & Nuts, Washers (for stock
verification purpose)
ST80 45 Labour charges for loading and unloading of ACSR, 413.93
AAA Conductor & Earth wire bits for weighiment (for
stock verification purpose).
ST81 46 Counting and Restocking of Hardware (Iron parts, Al 6.26
jumper cones, Al Tensition cones, PA rods, Arcing
horns, Al grippers etc) (for stock verification purpose).
ST82 47 Counting and Restocking of 220kV & 132kV Line 2.05
accessories like Dampers, MSC Joints, Repair sleeves,
PA rods, D- Shackles Links, Earthing sets, Hangers,
Counter Poise Earthing Clamps etc (for stock
verification purpose)
ST83 48 Counting and restocking of insulators of various 2.05
capacities (for stock verification purpose).
ST84 49 Loading of Assorted tower parts from different places 310.05
by observing part wise and loading in to lorry at stores.
ST85 50 For Opening and Repacking of Packing of Panels for 62.26
check measuring purpose
51 For Opening and Repacking of Packing of Breakers for
check measuring purpose
ST86 (a) 220 kV 206.08
ST87 (b) 132 kV 145.59
ST88 (c) 33 kV 62.26
ST89 52 For Opening and Repacking of Packing of Fragile 30.99
Materials, and Small Packages like wooden, Cartoon
Boxes etc., for check measuring purposes.
III Crane Hire charges:(for departmental works at the premises)
Sl. Item Description of Item SSR for
No. No. 2020-21
(Rs.)
53 For 2 to 8 Tonne Capacity crane
ST90 [Link] Ist hour 3,068.43
ST91 [Link] every hour or part thereof after Ist hour 1,393.79
54 For 8 to 20 Tonne Capacity crane
ST92 [Link] Ist hour 4,785.45
ST93 [Link] every hour or part thereof after Ist hour 1,595.11
55 For above 20 Tonne Capacity crane
ST94 [Link] Ist hour 7,379.71
ST95 [Link] every hour or part thereof after Ist hour 2,594.26

27
 File No.ENE51-PM0SYI(400)/12/2021-EE2

IV Sparing of Departmental vehicle to the contractor:

Sl. Item SSR for
Description of Item
No. No. 2020-21
Sparing of Departmental vehicle(Lorry) to the
contractor is under emergency only. When
departmental lorry is engaged to the Contractor on a 4,022.02
particular day an amount per day or part there of should
ST96 56 be recovered for a total KM run up to 100KM on that
day plus for every additional KM rate, which ever is
higher. The run to be worked out taking initial reading
at starting point and closing reading after returing 33.44
the same starting point duly completing the transport
work.
ST97 57 Providing Transportation to Officers 6.85
Note:
1 When the departmental lorry is used for transport of fragile and costly equipment,
they have to be insured by the contractor in first place before transport and the
same will be claimed in the respective work bill.
2 If the crane is given on hire to other than APTRANSCO works, the rate is a
minimum of Rs. 29283.12 (Rs.1220.13-per hr X 24Hrs) + (Fuel cost &
lubricants) per day or part thereoff and the time is to be reckoned from the time
of leaving department premises till reaching back.

28
 File No.ENE51-PM0SYI(400)/12/2021-EE2

ANNEXURE – VII
TRANSPORTATION, HANDLING CHARGES INVOLVED DURING ERECTION OF 400KV
TRANSMISSION LINES
SS Rate for 2020-
Item. 21
Sl. No. Description of Item Unit
No. (in Rs)

1 2 3 4 5
Total cost for transportation and handling
C4H1 1 Charges for Setting of Stub with Stub setting Each Set 949.93
template.
Erection of Tower: Total cost for
C4H2 2 transportation and handling Charges. Per MT 749.35

Double Circuit Stringing with Twin Moose:

C4H3 3 Transportation and handling charges for line Per KM 20,532.82
materials.
Single Circuit Stringing with Twin Moose :
C4H4 4 Transportation and handling charges for line Per KM 10,959.60
materials.
Double Circuit Stringing with Quadruple
C4H5 5 Moose: Transportation and handling charges for line Per KM 41,065.64
materials
Single Circuit Stringing with Quadruple
C4H6 6 Moose:Transportation and handling charges Per KM 21,920.83
for line materials.
OPG wire & earth wire: Transportation and
C4H7 7 handling charges for OPGW/earthing materials for 1 Per KM 624.18
kM for D/C stringing.
OPG wire &earth wire: Transportation and
C4H8 8 handling charges for OPGW/earthing materials for 1 Per KM 638.65
kM for S/C stringing.

29
 File No.ENE51-PM0SYI(400)/12/2021-EE2

ANNEXURE -VIII
TRANSPORT OF EQUIPMENTS / MATERIALS

Per Load
[Link]. Item No. Description of Item SSR
2020-21
The following are the minimum materials /
equipment, for each load. One Load = 9.0 MT
1 CTs, PTs, & CVTs:
T.1 1.a 220 kV 2 Nos.
T.2 1.b 132 kV 3 Nos.
T.3 1.c 33 kV 12 Nos.
NOTE: For transport of 220kV CTs, PTs &CVTs
extra provison may be added for each load
towards labour for clearing the obstructions 244.67
like electrically and telephone lines as the
equipment are very tall.(In Rupees)
2 SF6 Circuit Breakers:
T.4 2.a 220 kV 1/2 sets
T.5 2.b 132 kV 2/3 sets
T.6 2.c 33 kV 2 Nos.
Isolators with or without Earth switch
3
including post type insulators:
T.7 3.a 220 kV 1 set.
T.8 3.b 132 kV 2 Sets
T.9 3.c 33 kV 8 Nos.
4 Lighting Arrestors:
T.10 4.a 220 kV 6 Nos.
T.11 4.b 132 kV 6 Nos.
T.12 4.c 33 kV 24 Nos.
5 Control & Relay panels: 6 Nos.
6 ACSR Conductor and Earth wire drums:
T.13 6.a ACSR moose 3Nos.
T.14 6.b ACSR Zebra 4Nos.
T.15 6.c ACSR Panther 6Nos.
T.16 6.d Earth wire of 2 km per each drum 8Nos.
T.17 6.e Earth wire of 3 km per each drum 6 Nos.
T.18 6.f CABLE DRUMS 10Nos.
7 Disc Insulators
T.19 7.a 70 KN 1000 Nos.
T.20 7.b 120KN 800 Nos.
8 Silicon Rubber Insulators
T.21 8.a 70 KN 275 Nos.
T.22 8.b 120KN 228 Nos.
9 Wave Traps
T.23 9.a 220kV 6 Nos.
T.24 9.b 132kV 16 Nos.

30
 File No.ENE51-PM0SYI(400)/12/2021-EE2

ANNEXURE - IX
RATES FOR HANDLING & ERECTION OF POWER TRANSFORMERS
SS Rate for
Sl. Item
Description of Item Unit 2020-21
No. No.
(in Rs)
1 2 3 4
A) HANDLING AS JOB WORK BY DEPARTMENT
1 Loading/Unloading of T&P such as wooden sleepers,
winch jacks, packing pieces etc., required for handling the
power transformers.
PT1 a Up to 31.5 MVA transformers, one load of wooden sleepers Load
and another load of T&P such as chain pulley block and rail 1,363.40
poles etc (Maximum two loads)
PT2 b For above 31.5 MVA and up to 100 MVA transformers, two Load
loads of wooden sleepers and another load of T&P such as
1,363.40
chain pulley block, winch and rail poles etc (Maximum three
loads)
PT3 c For the above 100 MVA and up to 160 MVA transformers, Load
three loads of wooden sleepers and another load of T&P such 1,363.40
as winch machine and rail poles etc (Maximum Four loads)
2 Loading/Unloading of fragile material such as
a) LV bushing / Neutral bushing for 132 kV transformer
PT4 (i) Loading Each 40.77
PT5 (ii) Unloading Each 32.63
b) 132kV Bushings 0.00
PT6 (i) Loading Each 160.40
PT7 (ii) Unloading Each 160.40
c) 220kV Bushings 0.00
PT8 (i) Loading Each 320.80
PT9 (ii) Unloading Each 320.80
NOTE :If loading / Un loading is done with Crane, 1/3rd
Charges are to be paid towards labour charges and remaining
amount is towards crance hire charges.
PT10 3 Loading/Unloading of accessories of transformer including Load
raidator, pipe line, FCC & RTCC panels, conservator tank,
turrets LA set frames and oil barrels 'A' frame and header etc., 2,256.51
(For 50MVA and above 50 MVA PTRs without oil barrels)

4 Dragging of power transformer main tank duly arranging

wooden sleeper platform providing packing pieces, jacking
up the transformer, insertion of wooden sleeper, rail poles
arrangement of pullies, steel ropes positioning of winch
and anchoring of winch.
a Transformers upto 16 MVA capacity
PT11 Up to 10 Mtrs. LS 3,591.37
PT12 Over and above 10 Mtrs. RM 357.50
b Transformers above 16MVA and upto 31.5 MVA capacity
PT13 Up to 10 Mtrs. LS 6,558.81
PT14 Over and above 10 Mtrs. RM 656.57
c Transformers above 31.5MVA and upto 50 MVA capacity
PT15 Up to 10 Mtrs. LS 7,654.42
PT16 Over and above 10 Mtrs. RM 765.30
d Transformers above 50MVA and upto 100 MVA capacity
PT17 Up to 10 Mtrs. LS 9,459.62
PT18 Over and above 10 Mtrs. RM 944.74

31
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate for
Sl. Item
Description of Item Unit 2020-21
No. No.
(in Rs)
e Transformers above 100MVA and upto 160 MVA capacity
PT19 Up to 10 Mtrs. LS 12,170.13
PT20 Over and above 10 Mtrs. RM 1,217.96
5 Turning the transformer through 90 degrees including
making arrangements as above.
PT21 a Transformers upto 16 MVA capacity Each 3,214.84
PT22 b Transformers above 16MVA and upto 31.5 MVA capacity Each 4,031.78
PT23 c Transformers above 31.5MVA and upto 50 MVA capacity Each 5,014.58
PT24 d Transformers above 50MVA and upto 100 MVA capacity Each 5,737.76
PT25 e Each
Transformers above 100MVA and upto 160 MVA capacity 7,171.85
6 Turning the transformer through 180 degrees including
making arrangements as above.
PT26 a Transformers upto 16 MVA capacity Each 5,573.28
PT27 b Transformers above 16MVA and upto 31.5 MVA capacity Each 6,701.52
PT28 c Transformers above 31.5MVA and upto 50 MVA capacity Each 7,896.39
PT29 d Transformers above 50MVA and upto 100 MVA capacity Each 8,774.51
PT30 e Transformers above 100MVA and upto 160 MVA capacity Each 10,528.06
PT31 7(a) 1 Job
Anchoring of transformer including excavation of trench of 4
x 1x0. 5 mtrs for anchoring and burying 2 Nos. sleepers in it 1,363.40
and removing the same after work is completed.
PT32 7(b) Movement of 10 MT winch for anchoring. 1 Job 1,234.27
8 Lifting/Lowering the transformer main tank to the
required height of one sleeper using jacks and wooden
sleepers packing pieces for loading onto /from the truck.
PT33 a Transformers upto 16 MVA capacity Each 3,901.30
PT34 b Transformers above 16MVA and upto 31.5 MVA capacity Each 6,012.35
PT35 c Transformers above 31.5MVA and upto 50 MVA capacity Each 7,485.86
PT36 d Transformers above 50MVA and upto 100 MVA capacity Each 9,978.88
PT37 e Transformers above 100MVA and upto 160 MVA capacity Each 12,768.25
9 Pulling the transformer from platform to the truck for
loading/ from truck to the platform for unloading
PT38 a Transformers upto 16 MVA capacity Each 3,281.45
PT39 b Transformers above 16MVA and upto 31.5 MVA capacity Each 5,737.76
PT40 c Transformers above 31.5MVA and upto 50 MVA capacity Each 6,376.64
PT41 d Transformers above 50MVA and upto 100 MVA capacity Each 7,973.87
PT42 e Transformers above 100MVA and upto 160 MVA capacity Each 10,776.81
10 Fixing of transformer wheels to main tank including
alignment of transformer etc.,
PT43 a Transformers upto 16 MVA capacity Job 1,517.02
PT44 b Transformers above 16MVA and upto 31.5 MVA capacity Job 1,790.24
PT45 c Transformers above 31.5MVA and upto 50 MVA capacity Job 2,607.21
PT46 d Transformers above 50MVA and upto 100 MVA capacity Job 3,377.94
PT47 e Transformers above 100MVA and upto 160 MVA capacity Job 5,005.08
PT48 11 Arranging gas cutter equipment at site including operator and Job
helper to remove anchoring of transformer main tank on truck 2,486.23
for loading and unloading (including cost of gas)
12 Removal of steel rope and turn buckles of transformer
main tank on truck.

32
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate for
Sl. Item
Description of Item Unit 2020-21
No. No.
(in Rs)
PT49 (a) Up to 100MVA Capacity Job 683.75
PT50 (b) above 100MVA and up to 160MVA Capacity Job 1,023.57
13 Tieing the transformer main tank on to the truck with steel
rope and turn buckles
PT51 (a) Up to 100MVA Capacity Job 879.49
PT52 (b) above 100MVA and up to 160MVA Capacity Job 1,315.83
14 Assisting for lifting of overhead live lines, while transporting
of transformers by truck.
PT53 (a) Up to 100MVA Capacity Job 1,926.19
PT54 (b) above 100MVA and up to 160MVA Capacity Job 3,849.64
B) ERECTION OF POWER TRANSFORMERS AS JOB
WORK BY DEPARTMENT
1 Opening of crates and keep ready for erection of accessories
of transformers
PT55 a Transformers upto 16 MVA capacity Job 2,143.68
PT56 b Transformers above 16MVA and upto 31.5 MVA capacity Job 2,679.26
PT57 c Transformers above 31.5MVA and upto 50 MVA capacity Job 3,585.93
PT58 d Transformers above 50MVA and upto 100 MVA capacity Job 4,303.66
PT59 e Transformers above 100MVA and upto 160 MVA capacity Job 5,737.76
2 Shifting, loading dragging of accessories of transformers like
radiator, conservator tank, pipe line, fans, headers, DM box,
FCC, oil barrels etc., from place of storage to work spot and
vice versa of transformers.(For 50MVA and above 50 MVA
PTRs without oil barrels)
PT60 a Transformers upto 31.5 MVA capacity Job 3,214.84
PT61 b Transformers above 31.5MVA and upto 100 MVA capacity Job 4,290.06
PT62 c Transformers above 100MVA and upto 160 MVA capacity Job 5,892.71
PT63 d Transportation of oil barrels from unloading place to the filter Job
3,206.68
machine in the substation.
3 Erection of Radiators to the transformers including headers 0.00
PT64 a Transformers upto 16 MVA capacity Job 2,385.63
PT65 b Transformers above 16MVA and upto 31.5 MVA capacity Job 3,822.45
PT66 c Transformers above 31.5MVA and upto 50 MVA capacity Job 4,750.88
PT67 d Transformers above 50MVA and upto 100 MVA capacity Job 5,823.40
PT68 e Transformers above 100MVA and upto 160 MVA capacity Job 7,938.52
4 Erection of main conservator tank.
PT69 a Transformers upto 16 MVA capacity Each 2,151.85
PT70 b Transformers above 16MVA and upto 31.5 MVA capacity Each 2,392.44
PT71 c Transformers above 31.5MVA and upto 50 MVA capacity Each 3,509.81
PT72 d Transformers above 50MVA and upto 100 MVA capacity Each 5,465.89
PT73 e Transformers above 100MVA and upto 160 MVA capacity Each 7,035.92
PT74 f Pronal bag testing and commissioning Each 2,366.62
PT75 g Hiring of compressor Each 1,658.38
PT76 h Dry Nitrogen Cylinder (In case, Dry Nitrogen Cylinder is used Each
for commissioning of Air cell instead of Air compressor), 2,597.70
excluding transportation cost.
5 Erection of transformer bushing
PT77 a 33 kV Neutral and teritary bushings Each 468.98
PT78 b(I) 132 kV bushings up to 100MVA. Each 872.70
PT79 b(ii) 132 kV bushings for above 100MVA and up to 160MVA Each 1,092.91
PT80 c(I) 220 kV bushings up to 100MVA Each 1,311.77
PT81 c(ii) 220 kV bushings for above 100MVA and up to 160MVA Each 1,625.77

33
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate for
Sl. Item
Description of Item Unit 2020-21
No. No.
(in Rs)
PT82 d(I) 220kV 3 Nos. erection of turrets up to 100MVA Job 1,877.24
PT83 d(ii) 220kV 3 Nos. erection of turrets for above 100MVA and up to Job
2,463.10
160MVA
PT84 e(I) 132kV 3 Nos. erection of turrets up to 100MVA Job 880.84
PT85 e(ii) 132kV 3 Nos. erection of turrets for above 100MVA and up Job
1,291.38
to 160MVA
PT86 6 Erection of air blowers (cooling fans) including frames and Job
3,547.87
control cubical etc., (for each transformer)
PT87 7 Erection of LA frames (HV & LV side) Each 1,113.30
PT88 8(a) I).Erection of driving mechanism box, bevel gear of OLTC Each
1,113.30
for below 100MVA..
PT89 ii).Erection of driving mechanism box, bevel gear of OLTC Each
2,226.61
100MVA and above 100MVA.
PT90 8(b) ii).Erection of OLTC conservator tank with stand for up to Each
1,438.16
100MVA.
PT91 ii).Erection of OLTC conservator tank with stand for above Each
2,151.85
100MVA and upto 160MVA.
9 Erection of pipe line.
PT92 a Transformers upto 31.5 MVA capacity Each 753.06
PT93 b Transformers above 31.5MVA and upto 50 MVA capacity Each 1,125.54
PT94 c Transformers above 50MVA and upto 100 MVA capacity Each 1,907.15
PT95 d Transformers above 100MVA and upto 160 MVA capacity Each 2,384.29
PT96 10 I).Erection of Thermometer, pressure Relief valve and vent Each
753.06
pipe etc.,
PT97 ii)Erection of Thermometer, pressure Relief valve and vent Each
1,125.54
pipe etc.,100MVA and above PTRs.
11 Erection of detachable OLTC including connecting internal
jumper with OLTC tank.
PT98 a Transformers upto 31.5 MVA capacity Each 3,698.76
PT99 b Transformers above 31.5MVA and upto 100 MVA capacity Each 5,573.28
PT100 c Transformers above 100MVA and upto 160 MVA capacity Each 6,213.52
PT101 12 I).Erection of separate, cooler bay including 'A' frame header Bay
pipes and bends of transformers up to 100 PTRs MVA 7,973.87
capacity.
PT102 ii).Erection of separate, cooler bay including 'A' frame header Bay
pipes and bends of transformers above 100 MVA and up to 8,774.51
160MVA PTRs capacity.
13(I) Removal of old worn out gaskets and replacement with new
gaskets including cutting, pasting of gasket with all
accessories including cost of adhesives. Excl. top cover
PT103 a Transformers upto 16 MVA capacity Job 3,084.33
PT104 b Transformers 31.5MVA and 50 MVA capacity Job 4,793.01
PT105 c Transformers 100 MVA and upto 160 MVA capacity Job 6,167.31
13(II) Removal of old worn out gaskets and replacement with new
gaskets including cutting, pasting of gasket with all
accessories including cost of adhesives. for top cover. The
following rates are exclusive of crane hire charges which are
payable at actuals.
PT106 a Transformers upto 16 MVA capacity Job 1,544.21
PT107 b Transformers 31.5MVA and 50 MVA capacity Job 1,885.40
PT108 c Transformers 100 MVA and upto 160 MVA capacity Job 2,225.23
PT109 14 Erection of supporting insulators and earth flat for HV & LV Job
753.06
Neutrals / Tertiary.
C OIL FILTERATION OF TRANSFORMERS AS JOB
WORK BY DEPARTMENT

34
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate for
Sl. Item
Description of Item Unit 2020-21
No. No.
(in Rs)
PT110 1 Loading / Unloading of 2KL Oil filter. Job 2,633.03
PT111 2 Laying of [Link] from AC Supply point to filter Job
connecting Pipes etc, from filter to transformer and back to 1,272.33
filter and Vice-versa.
PT112 3 Loading / unloading of full transformer oil barrels. Barrel 51.67
PT113 4 Loading / unloading of oil drums. Barrel 8.15
5 Oil topping for transformer through oil filter:
5.1 Transformer already filled with oil
PT114 a Transformers upto 31.5 MVA capacity Each 1,011.35
PT115 b Transformers above 31.5MVA and upto 50 MVA capacity Each
2,226.61
when the transformer is received with transformer oil
PT116 5.2 Transformers above 50MVA upto 160 MVA capacity When Barrel
32.63
the transformer is received empty with Nitrogen
6 Assisting labour for filtering of oil for a period of 5 days
during filteration of oil
PT117 a For a period of 5 days for Transformers upto 31.5 MVA Each
4,807.97
capacity
PT118 b For a period of 5 days for Transformers above 31.5 MVA and Each
6,731.44
upto 100 MVA capacity
PT119 c For a period of 5 days for Transformers above 100 MVA and Each
9,618.66
upto 160 MVA capacity
PT120 a Over and above 5 days for Transformers upto 31.5 MVA per day
961.04
capacity
PT121 b Over and above 5 days forTransformers above 31.5 MVA and per day
1,345.74
upto 100 MVA capacity
PT122 c Over and above 5 days forTransformers above 100 MVA and per day
1,923.46
upto 160 MVA capacity
PT123 7(I) Dismantling of control cables of power transformer for Job
arranging, pulling of transformer maintank out of plinth for 889.01
failed transformer or improvement of transformercapacity.
PT124 (ii) Laying of control cables for the transformers which are Job
received with non completion of wiring on the transformer 2,366.62
and complete wiring of the transformer on the tank.F.C.C,D.M
box etc., (for old repaired transformers).
PT125 8 Shifting of filter machine in switch yard from existing place to RM
near transformer or to the convenient place manually (where 110.10
movement of tractor trailer is not possible).
9 Labour charges for arrangement for vaccum filling for the
power transformer for prescribed time duration for 50MVA
and above PTRs which are received at site with nitrogen gas
filled.
PT126 (a) Below 100MVA PTRs Job 3,547.87
PT127 (b) Above 100MVA PTRs. Job 7,098.46
PT128 10 Loading / Unloading of 5 KL Storage tanker. Job 1,174.47
11 Hire charges for a private tractor for transport of 6 KL of oil
filter.
PT129 Up to 50 KM LS 5,570.54
PT130 Beyond 50 KM per KM
107.40
12 Providing of oil tanker on daily hire charges
PT131 a 10 KL capacity Per day 1,746.74
PT132 b 20 KL capacity Per day
3,202.59
13 Transportation of 10 KL & 20 KL oil tanker (including
return trip charges), (a) or (b) only applicable
PT133 Minimum amount upto 50 KM LS 8,733.75

35
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate for
Sl. Item
Description of Item Unit 2020-21
No. No.
(in Rs)
PT134 More than 50 KM KM 43.49
14 Unloading of oil tanker at site and loading the same after
0.00
completion of the job
PT135 10 KL capacity Job 6,913.59
15(i) Complete wiring up of the transformer indicating systems
cooler control fans and motor driving mechanism of OLTC
panel providing suitable ferrules and lugs.
PT136 a) 16/31.5 MVA Transformer LS 20,853.57
PT137 b) 50 MVA Transformer LS 27,113.32
PT138 c) 100 MVA Transformer LS 30,071.24
PT139 d) 160 MVA Transformer LS 30,071.24
15(ii) Complete wiring up of the transformer indicating systems
cooler control fans and motor driving mechanism of OLTC
panel providing suitable ferrules and lugs excluding OLTC
panel
PT140 a) 16/31.5 MVA Transformer LS 10,427.45
PT141 b) 50 MVA Transformer LS 13,555.30
PT142 c) 100 MVA Transformer LS 15,034.26
PT143 d) 160 MVA Transformer LS 15,034.26
PT144 16 Draining of oil from main tank of the transformer into empty KL
oil drums and stacking them neatly as directed by the 508.39
APTRANSCO Engineer at site.
PT145 17 Unloading of 20 KL oil storage taken at site and loading the Job
7,552.48
same after comletion of the job
D) Insurance for fragile material during transportation, erection,
dismantling may be paid as per actuals from department side
for department works.

36
 File No.ENE51-PM0SYI(400)/12/2021-EE2

ANNEXURE - X
Rates for O&M works of EHT Lines
SS Rate for
Sl. Item 2020-21
Description of work Unit
No. No. (in Rs)

1 2 3 4
OM1 (a).Providing of Vibration dampers ( for 220 KV & 132 KV Each
1 154.97
lines) (Excluding Material & Transportation cost)
OM2 (b). Providing of spacer damper for 400 KV twin Moose lines Each
212.06
(Excluding Material & Transportation cost)
Painting of towers with two coats of aluminum paint using
Aluminum paint 1st grade containing 306 Kg of Aluminum
2 paste for 18 liters of thinner 1st coat is to be applied before
erection of towers and 2nd coat after stringing and half round
welding including cost of paint, cost of brushes, labour
charges etc., complete.
OM3 First coat of 1st Grade Aluminum Paint duly scratching and MT
a) cleaning of towers including labour charges, cost of paint, 4,950.71
brushes etc.
OM4 Labour charges for painting including scratching and cleaning MT
b) of towers of 1st coat of Alluminum with out cost of paint & 1,386.53
brushes.
OM5 (*) Second coat of 1st Grade Aluminium Paint duly scratching MT
c) and cleaning of towers including labour charges, cost of pint, 2,896.74
brushes, etc.
OM6 (*) Labour charges for painting including scratching and MT
d) cleaning of towers of 2nd coat of Aluminum with out cost of 785.69
paint & brushes.
(*) : The requirement of 2nd coat is to be justified by the
concerned Divisional Engineer/Executive Engineer before
execution of the work.
Painting of towers with single coat of red oxide paint of 1st
3
Grade, including scratching and cleaning of towers.
OM7 One coat of 1st Grade Red Oxide Paint including labour MT
a) charges for scratching and cleaning of towers including cost of 3,100.63
paint, brushes etc.
OM8 Labour charges for painting of towers including scratching and MT
b) cleaning of towers without cost of paint & brushes. 1,719.56

OM9 Providing of Arcing Horns for 132 KV line on both tower side per
4 and line side i.e. two per string (Excluding Material & string 1,241.06
Transportation cost)(with lefty & Pullies)
OM10 Providing of Arcing Horns for 132 KV line (Excluding Each
5 154.97
Material & Transportation cost)(without lefty & Pullies)
OM11 Providing of Arcing Horns for 220 KV line on both tower side per
6 and line side i.e. two per string (Excluding Material & string 1,821.51
Transportation cost)(with lefty & Pullies)
OM12 Providing of Arcing Horns for 220 KV line (Excluding Each
7 154.97
Material & Transportation cost)(without lefty & Pullies)
OM13 Providing of Missing angles/ Replacement of rusted angles on Per
8 the existing towers departmentally (including transporaton each 138.64
charges & Excluding cost of tower parts, bolts & nuts)

37
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate for
Sl. Item 2020-21
Description of work Unit
No. No. (in Rs)

OM14 Replacement of insulators at Suspension tower of 132 KV line Per

9 1,563.23
(Excluding Material & Transportation cost) string
OM15 Replacement of insulators at Tension tower of 132 KV line Per
10 2,645.28
(Excluding Material & Transportation cost) string
OM16 Replacement of insulators at Suspension tower of 220 KV line Per
11 1,719.56
(Excluding Material & Transportation cost) string
OM17 Replacement of insulators at Tension tower of 220 KV line Per
12 3,040.85
(Excluding Material & Transportation cost) string
OM18 Replacement of 132 KV line single suspension insulator string Per
13 with double suspension insulator strings (Excluding Material string 2,343.50
& Transportation cost)
OM19 Replacement of 132 KV line single tension insulator string Per
14 with double tension insulator strings (Excluding Material & string 3,966.55
Transportation cost)
OM20 Replacement of 220 KV line single suspension insulator string Per
15 with double suspension insulator strings (Excluding Material string 2,488.95
& Transportation cost)
OM21 Replacement of 220 KV line single tension insulator string Per
16 with double tension insulator strings (Excluding Material & string 4,560.57
Transportation cost)
OM22 Replacememt of insulators at Suspension tower of 400kV line Per
17 2,331.27
(Excluding material & Transportation cost ) string
OM23 Replacememt of insulators at Tension tower of 400kV line Per
18 3,887.70
(Excluding material & Transportation cost ) string
OM24 Painting the welded portion of GI bolts and nuts of towers In Each
the section ground level and up to X-arm level including all
19 5.82
bolts connecting the bracings at the bottom x-arm level with
one coat of zinc rich paint including cost of paing.
OM25 18 Fixing of earth bonds for existing transmission line towers Each 154.97
19 Re-Stringing of power conductor on the existing lines (for correction
OM26 a 3. Nos. Zebra conductors RKM 39,109.46
OM27 b 6. Nos. Zebra conductors RKM 58,662.16
OM28 c 2. Nos. Panther conductors RKM 20,853.57
OM29 d 3. Nos. Panther conductors RKM 31,285.13
OM30 e 6. Nos. Panther conductors RKM 49,538.30
OM31 f 2. Nos. Moose conductors RKM 33,023.70
OM32 g 3. Nos. Moose conductors RKM 49,538.30
OM33 h 6. Nos. Moose conductors RKM 78,213.48
OM34 i 3. Nos. Bear conductors RKM 39,109.46
OM35 j 6. Nos. Bear conductors RKM 58,662.16
OM36 k 3. Nos. Dog conductors RKM 23,462.15
OM37 l 6. Nos. Dog conductors RKM 37,152.02
21 Loading / Unloading charges :
For above half drum and up to one drum full drum rate Basic
Basic rate of
a) rate of Full Drum
Full
For below half drum and for a Piece Basic
Basic rate of
b) rate of
Half Drum
Half

38
 File No.ENE51-PM0SYI(400)/12/2021-EE2

ANNEXURE - XI
LABOUR CHARGES SSR PROPOSAL FROM TELECOM WING
SS Rate for
[Link]. Description Unit 2020-21
(in Rs)
1 Erection of PLCC panel in 220KV/132KV SS Each 7,705.82
2 Erection of LMU Each 1,286.73
3 Erection of Wave Trap
Fixing of wavetrap on pedastal mounting insulator stack in
i Each 7,200.74
400KV
Fixing o f the wave trap on pedastal mounting insulator stack in
ii Each 5,835.40
200KV
Fixing of the wave trap on Suspension mounting including
iii Each 3,478.83
jumpering in 132KV
Erection and commissioning of 48V DC/50A, 35A Battery
4 Each 2,542.37
charger in 220KV/132KV SS
Erection and commissioning of 48V DC/100A/150A Battery
5 Each 2,542.37
charger in 400 KV SS
Erection and commissioning of 48V/200AH & 250AH battery
6 Each 5,000.00
sets in 132 & 220 KV SS
Erection and commissioning of 48V/300AH battery sets in 132 &
7 Each 5,500.00
220 KV SS
8 Erection and commissioning of 48V/400AH battery set in 400 kV Each 6,000.00
SS
Erection and commissioning of OLTE & MUX (Optical line
9 Each 25,342.83
terminal equipment)
Erection and commissioning of FDP(Fibre Distribution Panel) in
10 Each 11,089.69
400KV/220KV/132KV SS (12F/24F/48F)

Erection and commissioning of 32/32, 16/16 or 8/8

11 Each 11,905.16
EPAX400KV/220KV/ 132KV SS
Erection and commissioning of 32/32, 16/16 with 2 E1 cards
12 Each 15,659.13
EPAX in 400KV/220KV/ 132KV SS
13 Erection of RTU panel in 400KV/220KV/132KV SS Each 19,580.42
Erection and commissioning of Analog/Digital protection coupler
14 Each 18,805.01
equipment in 400KV/220KV/132KV SS
Laying of optical fibre approach cable in switch yards of 400KV,
15 KM 20,540.69
220KV & 132KV (Including hardware) along with HDPE Pipe
16 Laying of HDPE Pipe in trenches in 400KV, 220KV, 132KVSS. KM 13,507.76
Laying of 12F/24/48 F OPGW cable on 132 kV, 220KV and 400
17 Km 79,547.29
KV lines (including Splicing and fixing of hardware accessories)
Stringing of ADSS type optical fibre cable (12F/24F capacity) on
18 132KV, 220KV line sections in plane areas/ forest areas/ hill
areas separately, inclusive of splicing and fixing of hardware
i accessories
For plane area KM 37,441.81
ii For agency or tribal area KM 46,802.27
iii For Hill areas KM 52,418.54
iv For interior area KM 52,418.54
For municipal coorporation areas (upto 12 Kms frrom
v KM 46,802.27
municipality)
vi For municipalites (upto 12 Kms from municipality) KM 44,930.17
19 Fixing of tension clamp set of OFC on 132KV & 220KV towers per set 2,566.18
20 Fixing of suspension clamp set of OFC on 132KV, 220KV towers per set 2,113.50
21 Fixing of tension clamp set of OPGW on 400KV lines per set 3,104.75
22 Fixing suspension clamp set of OPGW on 400KV lines per set 2,652.07
23 Fixing of splice box on 132KV & 220KV towers Each 3,861.35
24 Fixing of splice box on 400KV towers Each 4,826.69
25 Fixing of vibration dampers on 132KV & 220KV towers Per set 1,200.85
26 Fixing of vibration dampers on 400KV towers Per set 1,529.81

39
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate for
[Link]. Description Unit 2020-21
(in Rs)
Splicing charges for OFC fibres laid on 132KV, 220KV, 400KV
27 lines in plane Areas/Forest/ Hill Areas/ Municipal limits,
separately for each case
Each fibre
i For plane area 609.88
splice
Each fibre
ii for agency or tribal area 762.36
splice
Each fibre
iii for Hill areas 852.96
splice
Each fibre
iv for interior area 852.96
splice
for municipal corporation areas (upto 12 Kms from Each fibre
v 762.36
municipalities) splice
Each fibre
vi for municipalities (upto 12 Kms from municipalities) 731.87
splice
28 Fixing of ADSS type OFC to the tower members with ties, clamps
i etc.220kv/132 kv
for Each 2,106.22
ii for 400kv Each 2,632.78
29 Laying of aerial type OFC on 33KV/11KV HT/LT poles KM 12,404.43
Laying of 6 pair telephone cable in the trenches in 132KV,
30 KM 9,387.40
220KV & 400KV
31 Laying of Cat 5E/6 Cables in Offices. KM 4,814.06
Laying of Cat 5E/6 Cables with Conduit pipes along with
32 KM 14,442.17
accessories in Offices.
33 Fixing of 6U × 19 inch Rack in Offices for ERP works Each 401.17
Laying of single pair telephone cable in the trenches in 132KV,
34 KM 8,665.30
220KV & 400KV
Laying of 25sq mm battery cable in control room in 132kv,
35 KM 20,459.74
220KV & 400KV
Laying of Co-axial cable from switch yard gantry tower to
36 KM 19,641.35
communication room in the existing trench
37 Laying of 6 pair telephone cable on overhead poles LT & HT KM 7,221.08
38 Laying of single pair telephone cable on overhead poles LT & HT KM 7,221.08
39 Laying of RF cables in 132KV, 220KV & 400 KV SS KM 19,641.35
Digging of 1 X 1 X 1 ([Link]) ducts for laying of telephone cable
40 [Link] 748.17
in 132KV, 220KV, 400KV SS
Excavation, refilling & closing of ducts of 1 X 1 X 1 ([Link]) in
41 [Link] 1,496.34
132 KV, 220KV and 400 KV SS premises
Erection of earth pit as per standards in 132KV, 220KV SS for
42 Each 15,499.65
communication purpose
43 Erection of earth pit as per standards in 400 KV SS Each 15,499.65
44 Erection of VSAT equipment in 132KV, 220KV, 400 KV SS Each 7,339.02
45 Dismantling of VSAT equipment of 132KV, 220KV, 400 KV SS Each 3,669.51
Loading/unloading charges for PLCC equipment in 132KV SS,
46
220KV/400KV in to vehicle
i for single channel PLCC pannel Each 748.17
ii for Twin channel PLCC pannel Each 748.17
47 Loading/unloading charges for 48V/35A, 50A, chargers Each 748.17
48 Loading/unloading charges for 48V/100A/150A chargers Each 1,122.25
49 Loading/unloading charges for OLTE/MUX equipment Each 1,122.25
50 Loading/unloading charges for RTU panels Each 1,122.25
51 Loading/unloading charges for EPAXs Each 374.08
Loading/unloading charges for battery sets 48V/150 AH, 200 AH
52
,250 AH, 300 AH, 400 AH
i for 150 AH/200 AH Each 748.17
ii for 250 AH/300AH Each 748.17
iii for 400AH Each 1,122.25

40
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate for
[Link]. Description Unit 2020-21
(in Rs)
53 Loading/unloading charges for LMUs Each 374.08
54 Loading/unloading charges for Wavetrap
i 132KV wave trap Each 374.08
ii 220KV Wave Trap & 400 KV Each 748.17
55 Dismantling of exisiting PLCC chargers (35A, 50A, 100A)
i 35/50A Each 1,778.72
ii 100A Each 5,175.31
56 Dismantling of existing 48V/165AH, 200AH, 250AH,300AH Each 4,036.31
57 battery sets of existing 48V/400 AH battery sets
Dismantling Each 5,362.35
58 Dismantling of existing RTU, OLTE/MUX equipment
i RTU Each 9,790.22
ii OLTE/MUX Each 3,852.92
59 Dismantling of EPAXs Each 1,591.67
Dismantling of wave traps on 132 KV/220KV SS/400 KV SS
60
separately
i 50% of Erection of 2000A/1 m H Wave Trap(400 kv) Each 3,600.37
ii 50 % of Erection of 1250A/0.5 mH Wave Trap(220 kv) Each 2,917.70
iii 50% of Erection of 630A/0.2mH Wave Trap (132 KV) Each 1,739.42
Dismantling of 12F/24 F ADSS cable from 132KV, 220KV SS
61 Each 18,720.91
lines
Dismantling of 12F/24/48 F OPGW cable from 132KV, 220KV
62 Each 39,773.65
SS,400KVSS lines
Dismantling and bringing down of splice boxes on 132KV,
63 Each 1,930.68
220KV towers
64 Dismantling and bringing down of splice boxes on 400KV towers Each 2,413.35
Hiring charges of 5 KVA Diesel Generator per day for attending
65 Each 1,139.33
OFC break down works
Hiring charges of 230V AC inverter (2KVA) with battery backup
66 Each 1,139.33
for attending OFC break down works
Hiring charges of 8X8X10([Link]) closed tent shutter for attending
67 Each 802.34
splicing works for attending OFC break down works
68 Dismantling of VHF 30 ft masts with Gay wires etc. Each 2,349.30
69 Dismantling of 10 ft/20 ft trylon masts Each 1,896.62
UGOF cabling works rates
Survey & documentation
Survey of route, providing as built drawing, documentation for
70 Km 4,756.82
unarmoured underground optical fibre cable
Excavation &Backfilling
All types of soil, road, footpath, including PCC, sand, warning
71 brick/stone, semi-circular RCC split cover etc. for underground Km 1,90,121.67
fibre optic cable.
72 Warning Tape (including supply and installation). Km 28,526.40
73 Laying of PLB HDPE pipe O.D. 40mm Km 13,507.76
74 Installation of HDPE pipe by Trenchless digging
(a) 0-10 mtrs mtr 759.81
(b) > 10 and up to 30 mtrs mtr 855.87
(c) More than 30 mtrs mtr 950.49
75 Laying of GI pipe 100mm (Nominal bore), Including accessories. mtr 241.63
Laying of RCC hume pipe (NP3), 100mm Diameter (Inside),
76 mtr 362.44
Including accessories.
laying of unarmoured UG OFC 24F/48F (DWSM) with HDPE
77 Km 28,527.86
duct in case of underground works
Installation of Joint box in underground (Including splicing &
78 No. 5,947.49
testing) - 24 Fibers
79 Erection of RCC Joint Chambers No. 5,065.41

41
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate for
[Link]. Description Unit 2020-21
(in Rs)
Installation of PLB HDPE pipe on wall in building premises
80 mtr 480.34
including routing of OFC through it
Reinstatement of excavated area/damages (in road, pavement,
81 [Link] 240.17
footpath etc.)
82 Main Distribution frame (100 pairs) No. 2,378.42
83 Split type AC Units including Stabilizer No. 6,513.09

42
 File No.ENE51-PM0SYI(400)/12/2021-EE2

Annexure-XII (a)

LAYING OF 132KV UG CABLE (SINGLE CIRCUIT)

SS Rate for
Item 2020-21
[Link]. Description of Material/Work UNIT
No. (in Rs)
1 CABLE ROUTE SURVEY
U1S 1 a) Conducting reconnoitery and preliminary survey along
shortest route with best proposed route and furnishing
report for selecting the best proposal for approval
including cost and conveyance of all materials, hire
charges of equipment, tools and plant, preparation of
drawings and reports, labour charges, complete for Mts. 339.84
finished item of work as per the directions of Engineer-
in-charge at site as per SSR 2013-14. (a) With GPS
equipment (As per clause 4.9 of survey) (b) With total
station equipment.
U1S 2 b) Conducting Detailed Survey of cable route including
evaluation of thermal resistivity of the soil along the
cable route, excavation of trial pits as per field
requirements, preparation of cable route profile,
drawings for cable laying, final route alignment,
marking lines & grades, and preparing bill of materials/
lengths of the cable for the project incl. preparation of Mts. 1,019.50
PTCC questionnare and marking of proposed cable
route in topo sheet, tower/SS sketch, Single line
diagram etc.(30 copies/sets) .(NOTE: For survey of
small lengths of UG Cable, if the length of UG cable is
less than 0.5KM, then 0.5KM is considered for survey
of small length of UG cable in the preparation of
2 LAYING OF CABLE
2.1 Laying of 132 kv 630 sq. mm. XLPE U/G copper cable
(3 Nos. for single Circuit) including road cutting,
pulling and laying of cable including excavation in the
following soils and back filling, sand filling
dewatering, including cost of RCC protective tiles, cost
of route markers, warning tapes etc. Across and along
CC, BT & earth road, Nala crossings, bridge crossings,
providing HDPE (thickness 10 mm)pipes, Bell mouths,
end caps after laying cable, labour charges and all
incidental items of work for finished item of work.
This includes loading, unloading and transportation of
all materials to work spot. (flat formation)
U1S 3 a) Hard gravel soils, BC soils, red earth, stone and earth
Rmt 9,019.19
mixed with fair size boulders etc
U1S 4 b) Hard Rock with soils Rmt 12,390.35
U1S 5 c) CC or BT road surface etc. Rmt 8,038.43
U1S 6 d) Hard Rock Rmt 9,269.98
U1S 7 e) CC or BT road with Hard rock Rmt 17,220.07

43
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate for
Item 2020-21
[Link]. Description of Material/Work UNIT
No. (in Rs)
U1S 8 f) Across the road In HDPE pipes (thickness 10mm) to
cross CC or BT road and other service lines including
Rmt 11,302.88
cost of concrete cost of HDPE pipes of 250 mm dia etc.
complete
U1S 9 g) Across the road In HDPE pipes (thickness 10mm) to
cross CC or BT road with hard rock and other service
Rmt 26,610.35
lines including cost of concrete cost of HDPE pipes of
250 mm dia etc. complete
U1S 10 h) Cable laying in built up trenches, cable trays and
supports etc. complete including cost of trays and Rmt 11,302.88
support etc, complete.
U1S 11 i) Cable laying across the culverts and over bridges etc.,
Rmt 11,302.88
complete in PVC pipes of 250 mm dia in complete
U1S 12 j) Cable laying by clamping on special type tower
including earthing cable from termination to Link box Rmt 10,874.69
including cost of Aluminum clamps
U1S 13 k) Cable laying while clamping bare on the walls , ceiling
Rmt 4,078.00
and structures including cost of clamps in complete
U1S 14 l) shape
Cable laying across the railway tracks Rmt 27,186.72
U1S 15 m) Cable laying by clamping on Sub-station structures like
CPL etc., including earthing cable from termination to Rmt 2,039.01
Link box including cost of Aluminum clamps.
2.2 Including excavation and excluding backfilling
without cable laying
U1S 16 a) Hard Gravel soils, BC Soils, Red Earth, stone & Earth
Rmt 11,554.35
mixed with fair size boulders etc.,
U1S 17 b) Hard rock with CC or BT Road surfaces etc. Rmt 4,078.00
2.3 Excluding excavation and including backfilling 0.00
U1S 18 a) Hard Gravel soils, BC Soils, Red Earth, stone & Earth
Rmt 1,699.17
mixed with fair size boulders etc.,
U1S 19 b) Hard rock with CC or BT Road surfaces etc. Rmt 5,437.35
U1S 20 2.4 Only excavation and back filling of soil without laying
Rmt 2,039.01
of cable
U1S 21 2.5 Excavation and backfilling of suitable thermal backfill
for maintainings soil thermal resistance value of 120 Cum 5,437.35

U1S 22 2.6 degrees

Laying of cable excluding excavation and backfilling Rmt 543.74
2.7 Laying of cable by Horizontal Directional Drilling
(HDD) incl. cost of 250 mm HDPE Pipe
U1S 23 a) Soil/Morrem,soft rock (upto 5000 PSI) per each pipe Rmt 13,321.48
U1S 24 b) Soil/Hard rock (5000 PSI upto 9000 PSI) per each pipe Rmt 21,749.38
3 LAYING OF CO-AXIAL CABLE
U1S 25 a) [Link]. co-axial copper cable conductor PVC
Rmt 20.39
insulated 6.6KV grade across the cable.
U1S 26 b) [Link] core copper cable conductor PVC
Rmt 20.39
insulated 6.6KV grade across the cable.
U1S 27 c) [Link]. co-axial copper cable conductor PVC
insulated 6.6KV grade on pole mounted termination Rmt 20.39
tower including cost of cleats

44
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate for
Item 2020-21
[Link]. Description of Material/Work UNIT
No. (in Rs)
U1S 28 d) [Link] core copper cable conductor PVC
insulated 6.6KV grade on pole mounted termination Rmt 20.39
tower including cost of cleats.
4 For pulling optical fiber cable the following items
shall be done while excavation of trenches as per
U1S 29 a) specifications
Supply of HDPE duct pipe of OD/ID 40/33 mm dia and
associated material of standard make as per the
specification of the contract/tender and laying jointing,
RM 135.92
bedding of above HDPE duct pipe in the already
excavated XLPE cable trench including sealing the
section ends as per the specification of the
U1S 30 b) Supply of RCC joint chambers (1200/760/50 mm)
W/L/T with base and top plates as per the
specification of the contract/tender and erection of Each 9,515.35
RCC joint chambers for every 1KM in HDPE duct
enroot as per the specification of the contract/tender.

45
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate for
Item 2020-21
[Link]. Description of Material/Work UNIT
No. (in Rs)
5 CABLE JOINTING
Jointing of cable excluding cost of pre-moulded
straight through joints, Protection box, 3-phase solid
bond link box without SVL / 3-phase cross bond link
box with SVL, including excavation of pit for single
circuit cable, providing cement concrete base and walls
etc. including cost of cement, steel etc., labour charges
and all incidental items of work for finished item of
work including design of pit providing joint bay
identification mark including providing necessary
T&P for jointing viz., tarpaullin tent, DG Set, Air
Conditioner etc., complete wherever necessary for
complete item of work. This includes loading, un-
loading and transportation of all materials to work spot
U1S 31 a) as perexcavation
With drawing andof preparation of joint
joint bay size bay. and laying
(9mX4m)
Nos. 4,07,800.83
of CC([Link]) bed and sand bed and back filling
U1S 32 b) Jointing charges for cross bonding joints/normal joints Nos. 2,03,900.40
6 TERMINATION CHARGES
Termination of cable excluding cost of out door type
cable terminations and single phase link boxes without
SVL complete and all incidental item of work finished
item of work including providing necessary T&P viz.,
tarpaullin tent, DG set, air conditioner, scaffolding etc
complete wherever necessary for complete item of
work.
U1S 33 a) 132 KV tower mounted type cable end terminations
Each 4,75,767.65
including erection on tower in all respects
U1S 34 b) 132 kV Outdoor type cable end terminations with
Each 4,07,800.83
silicon materials complete in all respect.
U1S 35 c) 132 kV SF6 type cable end terminations complete in all
Each 4,07,800.83
respect.
U1S 36 7a Providing earthing of joint bays with copper flat of
cross section equivalent to the earthing cable and run
all around the joint bay, providing earth electrodes of
steel rods coated with copper as per standards and
treated with suitable earth enhancing compound to get
an effective diameter and welding the copper flat to the
Each 33,983.41
electrodes by exothermic weldng. The earthing scheme
drawing shall be got approved with all eath resistance
calculations considerting the fault currents earth leads
from link box to earth pit and connecing lug fixtures,
fasteners shall be supplied. Length of the earth lead
will be as per site condition/ connivance.

46
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate for
Item 2020-21
[Link]. Description of Material/Work UNIT
No. (in Rs)
U1S 37 7b Excavation of earth pit at CTT Tower, putting cast iron
pipe with flange on one end (as per ISS7181/86) of
nominal dia 125 mm and 2.75 metres long inside the
pit including supply and fixing of RCC Collars 0.75
mtr. dia (OD) 50mm thick and 0.60 mtrs. long inside
the pit, backfill the pit in the 25mm size granules of
Each 14,476.93
BH coke for full depth of the pit with alternate layers
of BH Coke and salt of 300mm thick around the earth
pipe of 150mm on all the sides of the pipe including
cost and conveyance of BH Coke,salt,clamps,CI pipes
and RCC collars, labour charges for all operational and
incidental items of work etc., complete.(as per SSR
U1S 38 8a 2013-14) for RCC ([Link]) for any unforeseen
Provision
(rate to be taken
requirement whenever necessary at culverts, drains, Cum
as per CSSR)
nalas, bridges.(rate to be taken as per CSSR)
U1S 39 8b Supplying, fitting and placing of HYSD, TMT bar
reinforcement (TISCO/SAIL/VSP) in foundtions,
colums , beams slabs wherever [Link] the
(rate to be taken
work as per the drawings furnished by the field MT
as per CSSR)
engineer including cutting , bending, cranking, tying
grill in position including cost of binding wire
scaffolding etc.(rate to be taken as per CSSR)
9 CONNECTION OF LINK BOXES
U1S 40 a) Erection of single phase link boxes, providing suitable
supporting arrangements, sheath bonding cable,
connecting earth leads, with all lugs, fixtures, clamps,
bolts and nuts etc., complete including excavation, Each 40,780.08
providing concrete box with walls of 75mm thick RCC
for inserting link boxes, and refilling, etc. including
earthing as per the directions of site engineer.

U1S 41 b) Erection of 3 phase link boxes making connections

with earth leads with lugs, fixtures, fasteners sheath
bonding cable etc., including excavation, providing
Each 54,373.44
RCC concrete wall box of 75mm thick for inserting
link boxes , and refilling, etc. including earthing as per
the directions of site engineer.
U1S 42 10 Erection of Lightning Arrestors on special type tower
including cost of hardware, jumpering with suitable
conductor between line conductor and the pole Each 6,796.69
mounted terminations including labour charges and
insurance for all incidental and operational items of
U1S 43 11 work. cutting charges and charges for way leaves to be
Road
paid for various Government and other agencies Mts. 8,156.01

U1S 44 12 Site testing and commissioning (including phase

sequence test, megger test, continuity test, HV test etc.) KM 2,71,867.23

47
 File No.ENE51-PM0SYI(400)/12/2021-EE2

Annexure-XII b
LAYING OF 132KV UG CABLE (DOUBLE CIRCUIT)
SS Rate
Item Sl.
Description of Material/Work UNIT for 2020-
No. No.
21 (in Rs)
1 CABLE ROUTE SURVEY
U1D 1 a) Conducting reconnoitery and preliminary survey along shortest
route with best proposed route and furnishing report for
selecting the best proposal for approval including cost and
conveyance of all materials, hire charges of equipment, tools
and plant, preparation of drawings and reports, labour charges, Mts. 339.84
complete for finished item of work as per the directions of
Engineer-in-charge at site as per SSR 2013-14. (a) With GPS
equipment (As per clause 4.9 of survey) (b) With total station
equipment.
U1D 2 b) Conducting Detailed Survey of cable route including
evaluation of thermal resistivity of the soil along the cable
route, excavation of trial pits as per field requirements,
preparation of cable route profile, drawings for cable laying,
final route alignment, marking lines & grades, and preparing
bill of materials/ lengths of the cable for the project incl. Mts. 1,359.35
preparation of PTCC questionnare and marking of proposed
cable route in topo sheet, tower/SS sketch, Single line diagram
etc.(30 copies/sets). (NOTE: For survey of small lengths of
UG Cable, if the length is less than 0.5KM, then 0.5KM is
considered in preparation of estimate).
2 LAYING OF CABLE
2.1 Laying of 132 kv 630 sq. mm. XLPE U/G copper cable (6 Nos.
for double Circuit) including road cutting, pulling and laying
of cable including excavation in the following soils and back
filling, sand filling dewatering, including cost of RCC
protective tiles, cost of route markers, warning tapes etc.
Across and along CC, BT & earth road, Nala crossings, bridge
crossings, providing HDPE (thickness 10 mm)pipes, Bell
mouths, end caps after laying cable, labour charges and all
incidental items of work for finished item of work. This
includes loading, unloading and transportation of all materials
to work spot. (flat formation)
U1D 3 a) Hard gravel soils, BC soils, red earth, stone and earth mixed
Rmt 16,312.04
with fair size boulders etc
U1D 4 b) Hard Rock with soils Rmt 21,749.38
U1D 5 c) CC or BT road surface etc. Rmt 13,593.36
U1D 6 d) Hard Rock Rmt 16,991.71
U1D 7 e) CC or BT road with Hard rock Rmt 32,624.07
U1D 8 f) Across the road In HDPE pipes (thickness 10mm) to cross CC
or BT road and other service lines including cost of concrete Rmt 20,390.05
cost of HDPE pipes of 250 mm dia etc. complete
U1D 9 g) Across the road In HDPE pipes (thickness 10mm) to cross CC
or BT road with hard rock and other service lines including
Rmt 26,610.35
cost of concrete cost of HDPE pipes of 250 mm dia etc.
complete
U1D 10 h) Cable laying in built up trenches, cable trays and supports etc.
Rmt 20,390.05
complete including cost of trays and support etc, complete.

48
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate
Item Sl.
Description of Material/Work UNIT for 2020-
No. No.
21 (in Rs)
U1D 11 i) Cable laying across the culverts and over bridges etc., complete
Rmt 20,390.05
in PVC pipes of 250 mm dia in complete
U1D 12 j) Cable laying by clamping on special type tower including
earthing cable from termination to Link box including cost of Rmt 21,749.38
Aluminum clamps
U1D 13 k) Cable laying while clamping bare on the walls , ceiling and
structures including cost of clamps in complete shape Rmt 8,156.01

U1D 14 l) Cable laying across the railway tracks Rmt 47,576.78

U1D 15 m) Cable laying by clamping on Sub-station structures like CPL
etc., including earthing cable from termination to Link box Rmt 4,078.00
including cost of Aluminum clamps.
2.2 Including excavation and excluding backfilling without
cable laying
U1D 16 a) Hard Gravel soils, BC Soils, Red Earth, stone & Earth mixed
Rmt 23,108.71
with fair size boulders etc.,
U1D 17 b) Hard rock with CC or BT Road surfaces etc. Rmt 8,156.01
2.3 Excluding excavation and including backfilling
U1D 18 a) Hard Gravel soils, BC Soils, Red Earth, stone & Earth mixed
Rmt 3,398.35
with fair size boulders etc.,
U1D 19 b) Hard rock with CC or BT Road surfaces etc. Rmt 8,156.01
U1D 20 2.4 Only excavation and back filling of soil without laying of cable Rmt 4,078.00
U1D 21 2.5 Excavation and backfilling of suitable thermal backfill for
Cum 10,874.69
maintainings soil thermal resistance value of 120 degrees
U1D 22 2.6 Laying of cable excluding excavation and backfilling Rmt 1,087.47
2.7 Laying of cable by Horizontal Directional Drilling (HDD)
incl. cost of 250 mm HDPE Pipe
U1D 23 a) Soil/Morrem,soft rock (upto 5000 PSI) per each pipe Rmt 13,321.48
U1D 24 b) Soil/Hard rock (5000 PSI upto 9000 PSI) per each pipe Rmt 21,749.38
3 LAYING OF CO-AXIAL CABLE
U1D 25 a) [Link]. co-axial copper cable conductor PVC insulated
Rmt 34.00
6.6KV grade across the cable.
U1D 26 b) [Link] core copper cable conductor PVC insulated
Rmt 34.00
6.6KV grade across the cable.
U1D 27 c) [Link]. co-axial copper cable conductor PVC insulated
6.6KV grade on pole mounted termination tower including cost Rmt 34.00
of cleats
U1D 28 d) [Link] core copper cable conductor PVC insulated
6.6KV grade on pole mounted termination tower including cost Rmt 34.00
of cleats.
4 For pulling optical fiber cable the following items shall be
done while excavation of trenches as per specifications
U1D 29 a) Supply of HDPE duct pipe of OD/ID 40/33 mm dia and
associated material of standard make as per the specification of
the contract/tender and laying jointing, bedding of above
RM 135.92
HDPE duct pipe in the already excavated XLPE cable trench
including sealing the section ends as per the specification of
the contract/tender.

49
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate
Item Sl.
Description of Material/Work UNIT for 2020-
No. No.
21 (in Rs)
U1D 30 b) Supply of RCC joint chambers (1200/760/50 mm) W/L/T with
base and top plates as per the specification of the
contract/tender and erection of RCC joint chambers for every Each 9,515.35
1KM in HDPE duct enroot as per the specification of the
contract/tender.
5 CABLE JOINTING
Jointing of cable excluding cost of pre-moulded straight
through joints, Protection box, 3-phase solid bond link box
without SVL / 3-phase cross bond link box with SVL,
including excavation of pit for double circuit cable, providing
cement concrete base and walls etc. including cost of cement,
steel etc., labour charges and all incidental items of work for
finished item of work including design of pit providing joint
bay identification mark including providing necessary T&P for
jointing viz., tarpaullin tent, DG Set, Air Conditioner etc.,
complete wherever necessary for complete item of work. This
includes loading, un-loading and transportation of all materials
to work spot as per drawing and preparation of joint bay.
U1D 31 a) With excavation of joint bay size (9mX4m) and laying of
Nos. 6,11,701.27
CC([Link]) bed and sand bed and back filling
U1D 32 b) Jointing charges for cross bonding joints/normal joints Nos. 2,03,900.40
6 TERMINATION CHARGES
Termination of cable excluding cost of out door type cable
terminations and single phase link boxes without SVL
complete and all incidental item of work finished item of work
including providing necessary T&P viz., tarpaullin tent, DG
set, air conditioner, scaffolding etc complete wherever
necessary for complete item of work.
U1D 33 a) 132 KV tower mounted type cable end terminations including
Each 4,75,767.65
erection on tower in all respects
U1D 34 b) 132 kV Outdoor type cable end terminations with silicon
Each 4,07,800.83
materials complete in all respect.
U1D 35 c) 132 kV SF6 type cable end terminations complete in all
Each 4,07,800.83
respect.
U1D 36 7a Providing earthing of joint bays with copper flat of cross
section equivalent to the earthing cable and run all around the
joint bay, providing earth electrodes of steel rods coated with
copper as per standards and treated with suitable earth
enhancing compound to get an effective diameter and welding
the copper flat to the electrodes by exothermic weldng. The Each 54,373.44
earthing scheme drawing shall be got approved with all eath
resistance calculations considerting the fault currents earth
leads from link box to earth pit and connecing lug fixtures,
fasteners shall be supplied. Length of the earth lead will be as
per site condition/ connivance.

50
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate
Item Sl.
Description of Material/Work UNIT for 2020-
No. No.
21 (in Rs)
U1D 37 7b Excavation of earth pit at CTT Tower, putting cast iron pipe
with flange on one end (as per ISS7181/86) of nominal dia 125
mm and 2.75 metres long inside the pit including supply and
fixing of RCC Collars 0.75 mtr. dia (OD) 50mm thick and 0.60
mtrs. long inside the pit, backfill the pit in the 25mm size
granules of BH coke for full depth of the pit with alternate Each 14,476.93
layers of BH Coke and salt of 300mm thick around the earth
pipe of 150mm on all the sides of the pipe including cost and
conveyance of BH Coke,salt,clamps,CI pipes and RCC collars,
labour charges for all operational and incidental items of work
etc., complete.(as per SSR 2013-14)
U1D 38 8a Provision for RCC ([Link]) for any unforeseen requirement (rate to be
whenever necessary at culverts, drains, nalas, bridges.(rate to Cum taken as per
be taken as per CSSR) CSSR)
U1D 39 8b Supplying, fitting and placing of HYSD, TMT bar
reinforcement (TISCO/SAIL/VSP) in foundtions, colums ,
(rate to be
beams slabs wherever [Link] the work as per the
MT taken as per
drawings furnished by the field engineer including cutting ,
CSSR)
bending, cranking, tying grill in position including cost of
binding wire scaffolding etc.(rate to be taken as per CSSR)
9 CONNECTION OF LINK BOXES
U1D 40 a) Erection of single phase link boxes, providing suitable
supporting arrangements, sheath bonding cable, connecting
earth leads, with all lugs, fixtures, clamps, bolts and nuts etc.,
complete including excavation, providing concrete box with Each 40,780.08
walls of 75mm thick RCC for inserting link boxes, and
refilling, etc. including earthing as per the directions of site
engineer.
U1D 41 b) Erection of 3 phase link boxes making connections with earth
leads with lugs, fixtures, fasteners sheath bonding cable etc.,
including excavation, providing RCC concrete wall box of Each 54,373.44
75mm thick for inserting link boxes , and refilling, etc.
including earthing as per the directions of site engineer.
U1D 42 10 Erection of Lightning Arrestors on special type tower including
cost of hardware, jumpering with suitable conductor between
line conductor and the pole mounted terminations including Each 6,796.69
labour charges and insurance for all incidental and operational
items of work.
U1D 43 11 Road cutting charges and charges for way leaves to be paid
Mts. 13,593.36
for various Government and other agencies
U1D 44 12 Site testing and commissioning (including phase sequence test,
KM 4,07,800.83
megger test, continuity test, HV test etc.)

51
 File No.ENE51-PM0SYI(400)/12/2021-EE2

Annexure-XII c
LAYING OF 220 KV UG CABLE (SINGLE CIRCUIT)
SS Rate for
Item Sl.
Description of Material/Work UNIT 2020-21
No. No.
(in Rs)
1 CABLE ROUTE SURVEY
U2S 1 a) Conducting reconnoitery and preliminary survey along shortest Mts. 339.84
route with best proposed route and furnishing report for selecting
the best proposal for approval including cost and conveyance of
all materials, hire charges of equipment, tools and plant,
preparation of drawings and reports, labour charges, complete for
finished item of work as per the directions of Engineer-in-charge
at site as per SSR 2013-14. (a) With GPS equipment (As per
clause 4.9 of survey) (b) With total station equipment.
U2S 2 b) Conducting Detailed Survey of cable route including evaluation of Mts. 1019.50
thermal resistivity of the soil along the cable route, excavation of
trial pits as per field requirements, preparation of cable route
profile, drawings for cable laying, final route alignment, marking
lines & grades, and preparing bill of materials/ lengths of the cable
for the project incl. preparation of PTCC questionnare and
marking of proposed cable route in topo sheet, tower/SS sketch,
Single line diagram etc.(30 copies/sets) .(NOTE: For survey of
small lengths of UG Cable, if the length of UG cable is less than
0.5KM, then 0.5KM is considered for survey of small length of
UG cable in the preparation of estimate)
2 LAYING OF CABLE
2.1 Laying of 220 kv 1000 sq. mm. XLPE U/G copper cable (3 Nos.
for Single Circuit) including road cutting, pulling and laying of
cable including excavation in the following soils and back filling,
sand filling dewatering, including cost of RCC protective tiles,
cost of route markers, warning tapes etc. Across and along CC, BT
& earth road, Nala crossings, bridge crossings, providing HDPE
(thickness 10 mm)pipes, Bell mouths, end caps after laying cable,
labour charges and all incidental items of work for finished item
of work. This includes loading, unloading and transportation of all
materials to work spot. (flat formation)
U2S 3 a) Hard gravel soils, BC soils, red earth, stone and earth mixed with Rmt 10823.03
fair size boulders etc
U2S 4 b) Hard Rock with soils Rmt 14868.42
U2S 5 c) CC or BT road surface etc. Rmt 9646.12
U2S 6 d) Hard Rock Rmt 11124.00
U2S 7 e) CC or BT road with Hard rock Rmt 20664.08
U2S 8 f) Across the road In HDPE pipes (thickness 10mm) to cross CC or Rmt 13563.47
BT road and other service lines including cost of concrete cost of
HDPE pipes of 250 mm dia etc. complete
U2S 9 g) Cable laying in built up trenches, cable trays and supports etc. Rmt 13563.47
complete including cost of trays and support etc, complete.
U2S 10 h) Cable laying across the culverts and over bridges etc., complete in Rmt 13563.47
PVC pipes of 250 mm dia in complete

52
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate for
Item Sl.
Description of Material/Work UNIT 2020-21
No. No.
(in Rs)
U2S 11 i) Cable laying by clamping on special type tower including earthing Rmt 12234.02
cable from termination to Link box including cost of aluminum
clamps
U2S 12 j) Cable laying by clamping on Sub-station structures like CPL etc., Rmt 2718.67
including earthing cable from termination to Link box including
cost of aluminum clamps.
U2S 13 k) Cable laying while clamping bare on the walls , ceiling and Rmt 5437.35
structures including cost of clamps in complete shape
U2S 14 l) Cable laying across the railway tracks Rmt 33983.41
2.2 Including excavation and excluding backfilling without cable
laying
U2S 15 a) Hard rock with CC or BT Road surfaces etc. Rmt 11554.35
U2S 16 b) Hard Gravel soils, BC Soils, Red Earth, stone & Earth mixed with Rmt 4078.00
fair size boulders etc.,
2.3 Excluding excavation and including backfilling
U2S 17 a) Hard Gravel soils, BC Soils, Red Earth, stone & Earth mixed with Rmt 1699.17
fair size boulders etc.,
U2S 18 b) Hard rock with CC or BT Road surfaces etc. Rmt 6796.69
U2S 19 2.4 Only excavation and back filling of soil without laying of cable Rmt 2039.01
U2S 20 2.5 Excavation and backfilling of suitable thermal backfill for Cum 5437.35
maintainings soil thermal resistance value of 120 degrees
U2S 21 2.6 Laying of cable excluding excavation and backfilling Rmt 679.66
2.7 Laying of cable by Horizontal Directional Drilling (HDD) incl.
cost of 250 mm HDPE Pipe
U2S 22 a) Soil/Morrem,soft rock (upto 5000 PSI) per pipe Rmt 13321.48
U2S 23 b) Soil/Hard rock (5000 PSI upto 9000 PSI) per pipe Rmt 21749.38
3 LAYING OF CO-AXIAL CABLE
U2S 24 a) [Link]. co-axial copper cable conductor PVC insulated 6.6KV Rmt 20.39
grade across the cable.
U2S 25 b) [Link] core copper cable conductor PVC insulated Rmt 20.39
6.6KV grade across the cable.
U2S 26 c) [Link]. co-axial copper cable conductor PVC insulated 6.6KV Rmt 20.39
grade on pole mounted termination tower including cost of cleats
U2S 27 d) [Link] core copper cable conductor PVC insulated Rmt 20.39
6.6KV grade on pole mounted termination tower including cost of
cleats.
4 For pulling optical fiber cable the following items shall be done
while excavation of trenches as per specifications
U2S 28 a) Supply of HDPE duct pipe of OD/ID 40/33 mm dia and associated RM 135.92
material of standard make as per the specification of the
contract/tender and laying jointing, bedding of above HDPE duct
pipe in the already excavated XLPE cable trench including sealing
the section ends as per the specification of the contract/tender
(Per Pipe).
U2S 29 b) Supply of RCC joint chambers (1200/760/50 mm) W/L/T with Each 9515.35
base and top plates as per the specification of the contract/tender
and erection of RCC joint chambers for every 1KM in HDPE duct
enroot as per the specification of the contract/tender.

53
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate for
Item Sl.
Description of Material/Work UNIT 2020-21
No. No.
(in Rs)
5 CABLE JOINTING
Jointing of cable excluding cost of pre-moulded straight through
joints, Protection box, 3-phase solid bond link box without SVL /
3-phase cross bond link box with SVL, including excavation of pit
for single circuit cable, providing cement concrete base and walls
etc. including cost of cement, steel etc., labour charges and all
incidental items of work for finished item of work including
design of pit providing joint bay identification mark including
providing necessary T&P for jointing viz., tarpaullin tent, DG Set,
Air Conditioner etc., complete wherever necessary for complete
item of work. This includes loading, un-loading and transportation
of all materials to work spot as per drawing and preparation of
joint bay.
U2S 30 a) With excavation of joint bay size (13mX4m) and laying of Each 475767.65
CC([Link]) bed and sand bed and back filling
U2S 31 b) Jointing charges for cross bonding joints for each phase Each 339834.02

6 TERMINATION CHARGES
Termination of cable excluding cost of out door type cable
terminations and single phase link boxes without SVL complete
and all incidental item of work finished item of work including
providing necessary T&P viz., tarpaullin tent, DG set, air
conditioner, scaffolding etc complete wherever necessary for
complete item of work.
U2S 32 a) 220 KV tower mounted type cable end terminations including Each 570921.16
erection on tower in all respects per phase including scaffolding
charges.
U2S 33 b) 220 kV Outdoor type cable end terminations with silicon materials Each 475767.65
complete in all respect.
U2S 34 c) 220 kV SF6 type cable end terminations complete in all respect. Each 475767.65
U2S 35 7a Providing earthing of joint bays with copper flat of cross section Each 33983.41
equivalent to the earthing cable and run all around the joint bay,
providing earth electrodes of steel rods coated with copper as per
standards and treated with suitable earth enhancing compound to
get an effective diameter and welding the copper flat to the
electrodes by exothermic weldng. The earthing scheme drawing
shall be got approved with all eath resistance calculations
considerting the fault currents earth leads from link box to earth
pit and connecing lug fixtures, fasteners shall be supplied. Length
of the earth lead will be as per site condition/ connivance.

54
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate for
Item Sl.
Description of Material/Work UNIT 2020-21
No. No.
(in Rs)
U2S 36 7b Excavation of earth pit at CTT Tower, putting cast iron pipe with Each 14476.93
flange on one end (as per ISS7181/86) of nominal dia 125 mm and
2.75 metres long inside the pit including supply and fixing of RCC
Collars 0.75 mtr. dia (OD) 50mm thick and 0.60 mtrs. long inside
the pit, backfill the pit in the 25mm size granules of BH coke for
full depth of the pit with alternate layers of BH Coke and salt of
300mm thick around the earth pipe of 150mm on all the sides of
the pipe including cost and conveyance of BH
Coke,salt,clamps,CI pipes and RCC collars, labour charges for all
operational and incidental items of work etc., complete.(as per
SSR 2013-14)
U2S 37 8a Provision for RCC ([Link]) for any unforeseen requirement Cum (rate to be
whenever necessary at culverts, drains, nalas, bridges.(rate to be taken as per
taken as per CSSR) CSSR)
U2S 38 8b Supplying, fitting and placing of HYSD, TMT bar reinforcement MT (rate to be
(TISCO/SAIL/VSP) in foundtions, colums , beams slabs wherever taken as per
[Link] the work as per the drawings furnished by the field CSSR)
engineer including cutting , bending, cranking, tying grill in
position including cost of binding wire scaffolding etc.(rate to be
taken as per CSSR)
9 CONNECTION OF LINK BOXES
U2S 39 a) Erection of single phase link boxes, providing suitable supporting Each 40780.08
arrangements, sheath bonding cable, connecting earth leads, with
all lugs, fixtures, clamps, bolts and nuts etc., complete including
excavation, providing concrete box with walls of 75mm thick
RCC for inserting link boxes, and refilling, etc. including earthing
as per the directions of site engineer including connecting to the
earthing cable from link box to earthpit
U2S 40 b) Erection of 3 phase link boxes making connections with earth Each 54373.44
leads with lugs, fixtures, fasteners sheath bonding cable etc.,
including excavation, providing RCC concrete wall box of 75mm
thick for inserting link boxes , and refilling, etc. including earthing
as per the directions of site engineer including connecting to the
earthing cable from link box to earthpit.
U2S 41 10 Erection of Lightning Arrestors on special type tower including Each 6796.69
cost of hardware, jumpering with suitable conductor between line
conductor and the pole mounted terminations including labour
charges and insurance for all incidental and operational items of
work.
U2S 42 11 Road cutting charges and charges for way leaves to be paid for Mts. 8156.01
various Government and other agencies. The cost is for estimate
purpose however, the amount will be reimbursed as per actuals
against documentary evidence.
U2S 43 12 Site testing and commissioning (including phase sequence test, KM 271867.23
megger test, continuity test, HV test etc.)

55
 File No.ENE51-PM0SYI(400)/12/2021-EE2

Annexure-XII d
LAYING OF 220 KV UG CABLE (DOUBLE CIRCUIT)
SS Rate for
Item
[Link]. Description of Material/Work Unit 2020-21
No.
(in Rs)
1 CABLE ROUTE SURVEY
U2D 1 Conducting reconnoitery and preliminary survey along shortest
route with best proposed route and furnishing report for
selecting the best proposal for approval including cost and
conveyance of all materials, hire charges of equipment, tools
a) and plant, preparation of drawings and reports, labour charges, Mts. 339.84
complete for finished item of work as per the directions of
Engineer-in-charge at site as per SSR 2013-14. (a) With GPS
equipment (As per clause 4.9 of survey) (b) With total station
equipment.
U2D 2 Conducting Detailed Survey of cable route including
evaluation of thermal resistivity of the soil along the cable
route, excavation of trial pits as per field requirements,
preparation of cable route profile, drawings for cable laying,
final route alignment, marking lines & grades, and preparing
bill of materials/ lengths of the cable for the project incl.
b) Mts. 1,359.35
preparation of PTCC questionnare and marking of proposed
cable route in topo sheet, tower/SS sketch, Single line diagram
etc.(30 copies/sets) .(NOTE: For survey of small lengths of
UG Cable, if the length of UG cable is less than 0.5KM, then
0.5KM is considered for survey of small length of UG cable in
the preparation of estimate).
2 LAYING OF CABLE
Laying of 220 kv 1000 sq. mm. XLPE U/G copper cable (6
Nos. for double Circuit) including road cutting, pulling and
laying of cable including excavation in the following soils and
back filling, sand filling dewatering, including cost of RCC
protective tiles, cost of route markers, warning tapes etc.
2.1 Across and along CC, BT & earth road, Nala crossings, bridge
crossings, providing HDPE (thickness 10 mm)pipes, Bell
mouths, end caps after laying cable, labour charges and all
incidental items of work for finished item of work. This
includes loading, unloading and transportation of all materials
to work spot. (flat formation).
U2D 3 Hard gravel soils, BC soils, red earth, stone and earth mixed
a) Rmt 18,038.40
with fair size boulders etc
b) Hard Rock with soils Rmt 24,780.68
U2D 5 c) CC or BT road surface etc. Rmt 16,076.92
U2D 6 d) Hard Rock Rmt 18,539.98
U2D 7 e) CC or BT road with Hard rock Rmt 34,440.14
U2D 8 Across the road In HDPE pipes (thickness 10mm) to cross CC
f) or BT road and other service lines including cost of concrete Rmt 22,605.74
cost of HDPE pipes of 250 mm dia etc. Complete.
U2D 9 Cable laying in built up trenches, cable trays and supports etc.
g) Rmt 22,605.74
complete including cost of trays and support etc, complete.
U2D 10 Cable laying across the culverts and over bridges etc.,
h) complete in PVC pipes of 250 mm dia in complete Rmt 22,605.74

56
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate for
Item
[Link]. Description of Material/Work Unit 2020-21
No.
(in Rs)
U2D 11 Cable laying by clamping on special type tower including
i) earthing cable from termination to Link box including cost of Rmt 24,468.04
aluminum clamps
U2D 12 Cable laying by clamping on Sub-station structures like CPL
j) etc., including earthing cable from termination to Link box Rmt 5,437.35
including cost of aluminum clamps.
U2D 13 Cable laying while clamping bare on the walls , ceiling and
k) Rmt 10,874.69
structures including cost of clamps in complete shape.
U2D 14 l) Cable laying across the railway tracks. Rmt 54,373.44
Including excavation and excluding backfilling without
2.2
cable laying
U2D 15 a) Hard rock with CC or BT Road surfaces etc. Rmt 23,108.71
U2D 16 Hard Gravel soils, BC Soils, Red Earth, stone & Earth mixed
b) Rmt 8,156.01
with fair size boulders etc.,
2.3 Excluding excavation and including backfilling
U2D 17 Hard Gravel soils, BC Soils, Red Earth, stone & Earth mixed
a) Rmt 3,398.35
with fair size boulders etc.,
U2D 18 b) Hard rock with CC or BT Road surfaces etc. Rmt 9,515.35
U2D 19 Only excavation and back filling of soil without laying of
2.4 Rmt 4,078.00
cable.
U2D 20 Excavation and backfilling of suitable thermal backfill for
2.5 maintainings soil thermal resistance value of 120 degrees. Cum 10,874.69

U2D 21 2.6 Laying of cable excluding excavation and backfilling. Rmt 1,359.35
Laying of cable by Horizontal Directional Drilling (HDD)
2.7
incl. cost of 250 mm HDPE Pipe
U2D 22 a) Soil/Morrem,soft rock (upto 5000 PSI) per pipe Rmt 13,321.48
U2D 23 b) Soil/Hard rock (5000 PSI upto 9000 PSI) per pipe Rmt 21,749.38
3 LAYING OF CO-AXIAL CABLE
U2D 24 [Link]. co-axial copper cable conductor PVC insulated
a) Rmt 34.00
6.6KV grade across the cable.
U2D 25 [Link] core copper cable conductor PVC insulated
b) Rmt 34.00
6.6KV grade across the cable.
U2D 26 [Link]. co-axial copper cable conductor PVC insulated
c) 6.6KV grade on pole mounted termination tower including Rmt 34.00
cost of cleats.
U2D 27 [Link] core copper cable conductor PVC insulated
d) 6.6KV grade on pole mounted termination tower including Rmt 34.00
cost of cleats.
For pulling optical fiber cable the following items shall be
4
done while excavation of trenches as per specifications.
U2D 28 Supply of HDPE duct pipe of OD/ID 40/33 mm dia and
associated material of standard make as per the specification
of the contract/tender and laying jointing, bedding of above
a) HDPE duct pipe in the already excavated XLPE cable trench
RM 135.92

including sealing the section ends as per the specification of

the contract/tender (Per Pipe).

57
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate for
Item
[Link]. Description of Material/Work Unit 2020-21
No.
(in Rs)
U2D 29 Supply of RCC joint chambers (1200/760/50 mm) W/L/T with
base and top plates as per the specification of the
b) contract/tender and erection of RCC joint chambers for every Each 9,515.35
1KM in HDPE duct enroot as per the specification of the
contract/tender.
5 CABLE JOINTING
Jointing of cable excluding cost of pre-moulded straight
through joints, Protection box, 3-phase solid bond link box
without SVL / 3-phase cross bond link box with SVL,
including excavation of pit for double circuit cable, providing
cement concrete base and walls etc. including cost of cement,
steel etc., labour charges and all incidental items of work for
finished item of work including design of pit providing joint
bay identification mark including providing necessary T&P
for jointing viz., tarpaullin tent, DG Set, Air Conditioner etc.,
complete wherever necessary for complete item of work. This
includes loading, un-loading and transportation of all materials
to work spot as per drawing and preparation of joint bay.
U2D 30 With excavation of joint bay size (13mX4m) and laying of
a) Nos. 6,93,261.43
CC([Link]) bed and sand bed and back filling
U2D 31 b) Jointing charges for cross bonding joints for each phase. Nos. 3,39,834.02
6 TERMINATION CHARGES
Termination of cable excluding cost of out door type cable
terminations and single phase link boxes without SVL
complete and all incidental item of work finished item of work
including providing necessary T&P viz., tarpaullin tent, DG
set, air conditioner, scaffolding etc complete wherever
necessary for complete item of work.
U2D 32 220 KV tower mounted type cable end terminations including
a) erection on tower in all respects per phase including Each 5,70,921.16
scaffolding charges.
U2D 33 220 kV Outdoor type cable end terminations with silicon
b) Each 4,75,767.65
materials complete in all respect.
U2D 34 220 kV SF6 type cable end terminations complete in all
c) Each 4,75,767.65
respect.
U2D 35 Providing earthing of joint bays with copper flat of cross
section equivalent to the earthing cable and run all around the
joint bay, providing earth electrodes of steel rods coated with
copper as per standards and treated with suitable earth
enhancing compound to get an effective diameter and welding
7a the copper flat to the electrodes by exothermic weldng. The Nos. 54,373.44
earthing scheme drawing shall be got approved with all eath
resistance calculations considerting the fault currents earth
leads from link box to earth pit and connecing lug fixtures,
fasteners shall be supplied. Length of the earth lead will be as
per site condition/ connivance.

58
 File No.ENE51-PM0SYI(400)/12/2021-EE2

SS Rate for
Item
[Link]. Description of Material/Work Unit 2020-21
No.
(in Rs)
U2D 36 Excavation of earth pit at CTT Tower, putting cast iron pipe
with flange on one end (as per ISS7181/86) of nominal dia 125
mm and 2.75 metres long inside the pit including supply and
fixing of RCC Collars 0.75 mtr. dia (OD) 50mm thick and 0.60
mtrs. long inside the pit, backfill the pit in the 25mm size
7b granules of BH coke for full depth of the pit with alternate Nos. 14,476.93
layers of BH Coke and salt of 300mm thick around the earth
pipe of 150mm on all the sides of the pipe including cost and
conveyance of BH Coke,salt,clamps,CI pipes and RCC collars,
labour charges for all operational and incidental items of work
etc., complete.(as per SSR 2013-14)
U2D 37 Provision for RCC ([Link]) for any unforeseen requirement (rate to be
8a whenever necessary at culverts, drains, nalas, bridges.(rate to Cum taken as per
be taken as per CSSR) CSSR)
U2D 38 Supplying, fitting and placing of HYSD, TMT bar
reinforcement (TISCO/SAIL/VSP) in foundtions, colums ,
(rate to be
beams slabs wherever [Link] the work as per the
8b MT taken as per
drawings furnished by the field engineer including cutting ,
CSSR)
bending, cranking, tying grill in position including cost of
binding wire scaffolding etc.(rate to be taken as per CSSR)
9 CONNECTION OF LINK BOXES
U2D 39 Erection of single phase link boxes, providing suitable
supporting arrangements, sheath bonding cable, connecting
earth leads, with all lugs, fixtures, clamps, bolts and nuts etc.,
complete including excavation, providing concrete box with
a) Each 40,780.08
walls of 75mm thick RCC for inserting link boxes, and
refilling, etc. including earthing as per the directions of site
engineer including connecting to the earthing cable from link
box to earthpit.
U2D 40 Erection of 3 phase link boxes making connections with earth
leads with lugs, fixtures, fasteners sheath bonding cable etc.,
including excavation, providing RCC concrete wall box of
b) 75mm thick for inserting link boxes , and refilling, etc. Each 54,373.44
including earthing as per the directions of site engineer
including connecting to the earthing cable from link box to
earthpit.
U2D 41 Erection of Lightning Arrestors on special type tower
including cost of hardware, jumpering with suitable conductor
10 between line conductor and the pole mounted terminations Nos. 6,796.69
including labour charges and insurance for all incidental and
operational items of work.
U2D 42 Road cutting charges and charges for way leaves to be paid
for various Government and other agencies. The cost is for
11 Mts. 13,593.36
estimate purpose however, the amount will be reimbursed as
per actuals against documentary evidence.
U2D 43 Site testing and commissioning (including phase sequence test,
12 KM 4,07,800.83
megger test, continuity test, HV test etc.)

59
 File No.ENE51-PM0SYI(400)/12/2021-EE2

ANNEXURE-XIII
TRANSMISSION LINE WORKS
[Link]. Description of work % Over the basic labour rates
1 River Crossing with JC type towers 100% extra
2 2nd Circuit Stringing with 1st Circuit lives75% extra
Works under shutdown:
This is applicable under the following
conditions only.
3 I. Pre-Programmed for interruption of 50% extra
line.
ii. Pre-arranged replacement/rectification
of line materials
4 Dismatling works 75% of Normal Rate
Emergency Works such as break down
works.
5 100% extra
This will bot be applicable for pre-
arranged shutdown works
6 Stringing of railway crossings 100% extra
7 National and State High way crossings 25% extra
Tree cutting & Jungle Clearance In Tr.
8 Line works as the works are in scattered 100% extra
areas
9 DC work under shutdown 100%extra

SUBSTATIONS AND OTHER WORKS

[Link]. Description of work % Over the basic labour rates
Works under shutdown:
This is applicable under the following
conditions only.
i. Pre-Programmed for interruption of
1 equipment. 50% extra
ii. Pre-programmed replacement of bus
in substation.
ii. Pre-arranged replacement
/rectification of equipment.
2 Dismatling works 75% of Normal Rate
Emergency Work such as break down
works.
3 100% extra
This will bot be applicable for pre-
arranged shutdown works
50% of basic labour rate of
Idle trip (No load) rate of the low-bedded loaded trip. Shortest destance
4 trailer for movement of Power from/ to the place of availability
Transformers. of low bedded trailer shall be
considered.

60
 File No.ENE51-PM0SYI(400)/12/2021-EE2

VOLUME-II
EQUIPMENT/MATERIAL RATES

61
 File No.ENE51-PM0SYI(400)/12/2021-EE2

MATERIAL/EQUIPMENT RATES FOR 220KV & 132KV SUBSTATIONS & LINES

C
a Ex-Works Price
without GST
[Link]. SAP Code t Description of Equipment/ Material Unit
e and F&I (in Rs)
g SSR-2020-21
o
1 10001372 220kV Circuit Breakers, SF6, 3pole, 3150A, 50KA Nos 13,00,000

2 10001377 132kV Circuit Breakers, SF6, 3pole, 3150A, 40KA Nos 5,50,000

3 10001380 132kV Circuit Breakers, SF6, 2Pole, 3150A, 40KA Nos 3,89,284

4 10001358 33 kV, 2500A, 25KA, Vaccum outdoor circuit breaker Nos 2,06,000

5 10001198 220kV CTs(800-600-400A/1-1-0.5,1-0.5,1-1A) Nos 2,45,000

220kV CT (800-500-300/1-0.66,1-0.375,0.5,0.625,0.83,1-
6 10001221 Nos 2,45,000
0.375,1-1A)

7 10001250 132kV CT (800-500/1-0.5775,0.66,1-1A) Nos 1,17,433

8 10001260 132kV CTs(600-300/1-1-1A) Nos 1,30,400

9 10001255 132kV CTs(300-200-100/1-0.5775,1-1A) Nos 96,689

10 10001265 132kV 0.2S Class metering CT of ratio 600/1 A Nos 1,20,570

11 10001266 132kV CT of ratio 300/1A (metering) Nos 1,20,163

12 10001100 33 kV CTs(2000/1-0.5775,1-1A) Nos 45,564

13 10001146 33kV CTs (1600-1200-800/1-0.5775,1-1-190.2S)A) Nos 56,170

10001104
14 33 kV CTs 1200 A Nos 45,564
10001103

15 10001108 33 kV CTs (400-200/1-1 A) Nos 31,697

16 10001110 33KV CT of ratio (240-120/1-1A) Nos 28,167

17 10001141 33kV NCTs 10/1A Nos 23,473

18 10001326 220kV PTs Nos 2,33,042

19 10001329 132kV PTs Nos 1,05,076

20 10001320 33 kV PTs Nos 32,000

21 10001301 220kV CVTs-3 core Nos 1,40,000

22 10001303 132kV CVTs Nos 1,20,000

62
 File No.ENE51-PM0SYI(400)/12/2021-EE2
C
a Ex-Works Price
without GST
[Link]. SAP Code t Description of Equipment/ Material Unit
e and F&I (in Rs)
g SSR-2020-21
o
23 10003102 220kV LAs Nos 45,000

24 10003105 132kV LAs Nos 32,000

25 10003108 33 kV LAs Nos 3,368

26 10002590 220kV 1600A Isolators without E/S Nos 1,67,100

27 10002588 220kV 1600A Isolators with E/S Nos 2,17,500

28 10002594 220kV 800A Isolators without E/S Nos 1,20,300

29 10002593 220kV 800A Isolators with E/S Nos 1,70,700

30 10002631 132kV 800A Isolators with E/S Nos 1,22,100

31 10002632 132kV 800A Isolators without E/S Nos 84,997

32 10002501 33 kV Isolators-2000 A Nos 46,439

33 10002503 33 kV Isolators-1200/1250A Nos 33,362

34 10002504 33 kV Isolators-800 A Nos 30,283

35 10007518 220kV Solid core insulators (with creepage 25 mm/KV) Nos 17,800

36 10007517 220kV Solid core insulators (with creepage 31 mm/KV) Nos 22,500

37 10007528 132kV Solid core insulators (with creepage 31mm/KV) Nos 8,000

38 10007528 132kV Solid core insulators (with creepage 25mm/KV) Nos 8,000

39 10007535 33kV Solid core insulators (with creepage 25mm/KV) Nos 1,900

40 10005213 220V,200AH Battery set (VRLA) Nos 3,19,000

41 10005218 220V,100 AH Battery set(VRLA) Nos 1,98,000

42 10005302 220V, 200AH Battery charger Nos 2,13,237

43 10005306 220V, 100AH Battery charger Nos 2,09,044

44 10000704 250KVA 33/0.415 KV Station Transformer Nos 3,57,954

45 10000705 100KVA 33/0.415 KV Station Transformer Nos 2,40,570

63
 File No.ENE51-PM0SYI(400)/12/2021-EE2
C
a Ex-Works Price
without GST
[Link]. SAP Code t Description of Equipment/ Material Unit
e and F&I (in Rs)
g SSR-2020-21
o
46 10004150 LTAC panel Nos 1,65,000

47 10004155 220kV PTDB panel Nos 53,350

48 10004156 132KV PTDB Panel Nos 46,786

49 10003211 2CX2.5 [Link] unarmoured copper control cable Km 39,045

50 10003217 4CX2.5 [Link] unarmoured copper control cable Km 60,287

51 10003223 6CX2.5 [Link] unarmoured copper control cable Km 89,429

52 10003228 10CX2.5 [Link] unarmoured copper control cable Km 1,42,712

53 10003230 12CX2.5 [Link] unarmoured copper control cable Km 1,67,852

54 10003389 3.5CX120 [Link] Al. power cable Km 2,85,584

55 10007604 220kV 70KN SRC Insulators Nos 3,400

56 10007603 220kV 120KN SRC Insulators Nos 3,600

57 10007607 132kV 70KN SRC Insulators Nos 2,187

58 10007605 132kV 120KN SRC Insulators Nos 2,393

59 10007514 70KN Porcelin normal Disc Insulators Nos 295

60 10007512 120KN Porcelin normal Disc Insulators Nos 550

160KN Porcelin Antifog Disc Insulators with Zinc Sleeve

61 10007508 Nos 1,030
470mm creepage

62 10010101 ACSR Panther conductor Km 1,45,000

63 10010103 ACSR Moose Conductor Km 3,25,000

64 10010176 7/3.15 mm HTGS wire Km 25,500

65 10007650 Bolts & Nuts MT 78,737

HDouble suspension H/W (AGS type) for Panther

66 10007079 a Nos 3,663
conductor
r
H
67 10007106 aSingle Suspension H/W for Panther (Pilot) Nos 1,359
rH
68 10007102 aSingle Suspension H/W (AGS-FAH) Panther ACSR Nos 1,663
r

64
 File No.ENE51-PM0SYI(400)/12/2021-EE2
C
a Ex-Works Price
without GST
[Link]. SAP Code t Description of Equipment/ Material Unit
e and F&I (in Rs)
g SSR-2020-21
o
H
69 10007103 aSingle Suspension H/W (AGS -AAH) for Panther ACSR Nos 1,840
rH
70 10007032 aDouble Tension H/W for Panther ACSR Nos 3,152
rH
71 10007052 aSingle Tension H/W for Panther ACSR Nos 1,591
rH
72 10007205 aMid Span Compression joints for Panther Nos 392
rH
73 10007278 aVibration dampers for Panther ACSR Nos 428
rH
74 10007223 aRepair sleeves for Panther conductor Nos 206
rH
75 10007089 aSingle Suspension H/W (AAH type) for Moose Conductor Nos 3,570
r
H
76 10007028 aDouble Tension H/W suitable for Moose Nos 4,881
rH
77 10007037 aSingle Tension H/W suitable for Moose Nos 2,765
rH
78 10007074 aDouble suspension h/w (AGS type) for moose conductor Nos 4,540
rH
79 10007090 aSingle Suspension H/W (FAH) for Moose Nos 3,064
rH
80 10007085 aSingle Suspension H/W suitable for Moose (Pilot) Nos 1,108
r
H
81 10007083 a220kV Single suspension hardware for Twin moose Nos 3,500
rH
82 10007073 a220kV Double suspension hardware for twin moose Nos 4,500
rH
83 10008562 aSpacer clamps with 400mm spacing for twin moose Nos 446
rT clamps for twin moose to single moose with 400mm
H
84 10008788 a Nos 707
spacing
rH Suspension clamps suitable for twin Moose conductor for
85 10007235 a Nos 555
220kV and 132kV
rH
86 10007200 aMid Span Compression joints for Moose Nos 843
rH
87 10007218 aRepair sleeves for Moose conductor Nos 346
rH
88 10007276 aVibration dampers for Moose conductor Nos 829
r
H
89 10007301 aArmour Rods for Moose ACSR conductor Nos 1,621
rH
90 10007292 aArcing Horns for Single suspension Moose Nos 294
rH
91 10007306 aArcing Horns for Single V-Suspension Moose Nos 218
r

65
 File No.ENE51-PM0SYI(400)/12/2021-EE2
C
a Ex-Works Price
without GST
[Link]. SAP Code t Description of Equipment/ Material Unit
e and F&I (in Rs)
g SSR-2020-21
o
H
92 10007069 aTension hardware with earth bond Nos 625
rH
93 10007321 aSuspension hardware with earth bond Nos 803
rH
94 10007209 aMidspan compression Joints for earth wire Nos 91
rT
95 67500060 oNumber plates with Bolts &Nuts and Washers Nos 151
w
T
96 67500058 oPhase Plates with Bolts &Nuts and Washers Set 192
w
T
97 67500055 oCircuit plate with Bolts &Nuts and Washers Nos 240
w
T
98 67500061 oDanger Boards with Bolts &Nuts and Washers Nos 168
w
T
99 67500042 oBird guards Nos 200
w
T
100 67500028 oAnti-Climbing devices Set 2,601
w
T
101 10007787 oU Bolts 16mm Nos 140
w
T
102 10007790 oU Bolts 20mm Nos 187
w
H
103 67500046 aHangers 132 KV 541
n
H
104 67500076 aHangers 220 KV 612
n
H
105 10008844 aArmour Rods for Panther ACSR conductor Nos 680

10007289 n
H
106 Arcing Horns for Panther ACSR conductor Nos 550
10007290 a
n5 bolted type single tension h/w for single moose or zebra
H
107 10007039 a Nos 1,900
conductor for 220kV & 132kV
rH 5 bolted twin zebra / moose tension h/w 400mm spacing
108 10007029 a Sets 3,900
for 132/220kV bus
rH 3 bolted type single tension h/w for single moose or zebra
109 10007038 a Nos 1,253
conductor for 33KV
rH 3 bolted tension hardware for twin moose with 150mm
110 10007036 a Nos 3,300
spacing to 33KV bus
rC
111 10008276 lT Clamps for single Moose all three ways Nos 600
aCT clamps for twin Moose T off single Moose with 150mm
112 10008918 l Nos 542
spacing
aC
113 10008576 lSpacer clamps with 150mm spacing for twin moose Nos 300
aCPost type insulators clamps for twin conductor for 220kV
114 10008933 l Nos 704
& 132kV
a

66
 File No.ENE51-PM0SYI(400)/12/2021-EE2
C
a Ex-Works Price
without GST
[Link]. SAP Code t Description of Equipment/ Material Unit
e and F&I (in Rs)
g SSR-2020-21
o
CPost type insulators clamps for single conductor for 220kV
115 10008932 l Nos 550
& 132kV
aC
116 10007526 lPost type insulators clamps for twin conductor for 33KV Nos 700
aC
117 10008740 lPost type insulators clamps for single conductor for 33KV Nos 510
aC
118 10008105 lPad type compressor clamp for GS Earth wire to 75/12 flat Nos 80
aC
119 10008106 lCleat type clamp for G.S. Earth wire Nos 78
a
120 10008104 CT clamp for GS Earth wire Nos 300
l
C
121 10008865 Bolted earth wire tension clamp Nos 590
l
a
122 10002935 Supply and fixing GI flexible earth bonds Nos 300

123 10006608 Supply and erection of LED lamps (120W) with fixture Nos 5,709

124 10009201 Marshalling Kiosk Nos 20,656

10009209
125 10009210 CT Marshalling boxes(220/132/33KV) Nos 3,985
10009211
126 10009214 PT Marshalling boxes(220/132/33KV) Nos 5,310

127 10009228 LT Distribution box with MCCB Nos 11,129

10009221
128 Lighting Pillar Box Nos 8,023
10009222
FCO2 portable fire extinguishers of 15 Lbs capacity without
129 10009701 i Nos 4,500
trolley and hose pipe
rFCO2 portable fire extinguishers of 50 Lbs capacity and
130 10009702 i Nos 18,500
hose pipe
rFDCP type fire extinguishers with horn and hose pipe 50Kg
131 10009713 i Nos 14,384
capacity, Trolley mounted
rFCO2 type portable fire extinguishers of 9 kgs capacity
132 10009723 i Nos 8,352
with trolley mounted
10009957 D r
133 15KVA DG set (CGL/Kirloskar) Nos 1,82,900
10009958 G
s
D
134 10009956 G 25KVA DG set (CGL/Kirloskar) Nos 2,35,900
s
135 10000712 33KV HG fuse set with insulators Nos 12,845

136 70002757 MDF Board with 12mm thick 3x4 size with teak wood Nos 5,728

Portable Twin Tube 20W emergency portable Lamp of

137 10009464 Nos 1,300
make Philips or bajaj

67
 File No.ENE51-PM0SYI(400)/12/2021-EE2

EQUIPMENT/MATERIAL RATES FOR 400KV SUBSTATIONS & LINES WORKS

Rates without
SAP Material GST & F&I
Sl. No. Description Unit
Code (in Rs.)
2020-21
A) ISOLATORS
420 KV 3 pole outdoor type horizontal centre break
Isolators 3 phases 50 c/s of 3150 Amps and fault level of
I 50 KA per second A.C. Motor operated with all
accessories, auxiliaries marshalling boxes, Terminal
Connectors other essentials as specified.
a) With single earth switch 7,22,706
10002550 (i) Metallics Sets 4,82,262
10007507 (ii) Insulators (1 set = 6 Nos. Insulators) Sets 2,40,444
b) With double earth switch 8,67,257
10002551 (i) Metallics Sets 6,26,813
10007507 (ii) Insulators (1 set = 6 Nos Insulators) Sets 2,40,444
245 KV 3 pole outdoor type horizontal double break
Isolators 3 phases 50 c/s of 1600 Amps and fault level of
40 KA per second A.C. Motor operated with all
II
accessories, auxiliaries marshalling boxes, Terminal
connectors other essentials as specified.( creepage
distance of 31mm/kV)
a) With Double earth switch 4,18,000
10002586 (i) Metallics Sets 2,56,406
10007517 (ii) Insulators (1 set = 9 Nos. Insulators) Sets 1,61,594
b) With single earth switch 3,56,559
(i) Metallics Sets 1,99,459
(ii) Insulators (1 set = 9 Nos. Insulators) Sets 1,57,100
c) Without earth switch 2,98,076
(i) Metallics Sets 1,40,976
(ii) Insulators (1 set = 9 Nos. Insulators) Sets 1,57,100
245 KV 3 pole outdoor type horizontal double break
Isolators 3 phases 50 c/s of 2500 Amps and fault level of
40 KA per second ,A.C. Motor operated with all
III
accessories, auxiliaries marshalling boxes, Terminal
connectors other essentials as specified. (creepage
distance of 31mm/kV)
a) with Single earth switch 3,93,249
10002580 (i) Metallics Sets 2,36,149
10007517 (ii) Insulators (1 set = 9 Nos. Insulators) Sets 1,57,100
B) CIRCUIT BREAKERS
420 KV 3 pole SF6 Gas filled out door circuit breakers
without closing resistors of 3 phases 50 c/s of 3150Amps
and fault level of 50 KA for one second either spring
charged motor operated or pneumatically operated with all
1 10001370 accessories, auxiliaries including terminal connectors and Sets 24,50,000
marshalling boxes and first fill of SF6 Gas with additional
10% gas and others as specified including Support
structures complete as specified for the 420 kV Circuit
Breakers.

In the above breakers, Main and Tie 400kV Circuit

2 10001442 Breakers of 125 MVAR Bus Reactor shall be supplied Nos 3,74,603
with CSDs. The rate for Control Switching Device in CB.

68
 File No.ENE51-PM0SYI(400)/12/2021-EE2
Rates without
SAP Material GST & F&I
Sl. No. Description Unit
Code (in Rs.)
2020-21
C) Lightening Arrestors
Design, Engineering, manufacture, assembly, shop testing,
supply and delivery at site including packing, forwarding,
handling at port of disembarkation, transportation to
1 project site, unloading of the following surge arrestors
complete with surge counters, insulating bays and all
associated accessories and auxiliaries in accordance with
specification including terminal connectors.

i) 10003100 390kV Lightening Arrestor Nos 1,06,575

D) Battery and Battery Charger
220V, 400AH, capacity sealed maintenance free valve
regulated lead acid 2 Nos. Battery banks supplied in
1 10005209 Sets 12,00,654
factory charged condition along with all other required
accessories (i.e) connectors etc.
2 Nos., 40/100 A FC & Float-Cum-Boost charger with
communication interface suitable for SAS IEC 61850 and
2 10005318 for SMF VRLA Battery banks along with all required Sets 9,70,283
accessories etc. with centre zero DC earth leakage
ammeter.
Design, Manufacture, Shop testing, Supply of AC &
F)
DC Distribution Boards as per the specification.
415V AC Main Board (Sub-Boards-I & II) as per Specn.
1 10004160 set 14,43,956
& Drawing as detailed below
i) ' I ' Type Module with a rating of 1250 A (ACB) - 2
Nos.
ii) 'I (BC) ' Type Module with a rating of 1250 A(ACB) -
1 No.
iii)' F1 ' Type Module with a rating of 800 A - 2 Nos.
iv) ' F1 ' Type Module with a rating of 400 A - 7 Nos.
v)' I ' Type Module with a rating of 1250 A (ACB) - 1
No.
vi)' F1' Type Module with a rating of 630 A - 3 Nos.
vii) ' E1' Type Module suitable for incoming feeder - 2
Nos.
viii) ' V1 ' Type Module with a rating of 0 - 500 V - 2
Nos.

ix) Cost of all Busbars, Cabling, Wiring meters etc. & all
other required accessories etc. as per specification - 1 set

x) Cost of the panel with all other required accessories etc.

as per specification - 1 set
COMPACT OUT DOOR ACMB incl. disconnector-1000
1(b) 10004167 amps- 1 Nos,MCCB-630 A- 2 Nos,MCCB-400 A- 2 sets 4,31,163
Nos,MCCB-63 A- 4 Nos
415V AC Distribution Board (Sub-Boards-I & II) as per
2 10004161 set 16,32,949
Specn. & Drawing as detailed below
i) ' F1' Type Module with a rating of 800 A - 2 Nos.
ii) ' F1 (BC) ' Type Module with a rating of 800 A - 1
No.
iii) ' DG' Type Module with a rating of 1250 A (ACB) -
1 No.
iv) ' F1' Type Module with a rating of 200 A - 4 Nos.

69
 File No.ENE51-PM0SYI(400)/12/2021-EE2
Rates without
SAP Material GST & F&I
Sl. No. Description Unit
Code (in Rs.)
2020-21
v) ' F1' Type Module with a rating of 150 A - 2 Nos.
vi) ' F1' Type Module with a rating of 125 A - 4 Nos.
vii) ' F1' Type Module with a rating of 63 A - 67 Nos.
viii) ' F1' Type Module with a rating of 32 A - 12 Nos.
ix) ' F1' Type Module with a rating of 16 A - 4 Nos.
x) ' V2 ' Type Module with a rating of 0 - 500 V - 2
Nos.
xi) Cost of the panel with all other required accessories
etc. as per specification - 1 set

xii) Cost of all Busbars, Cabling, Wiring meters etc. & all
other required accessories etc. as per specification - 1 set

415V AC Lighting Board (Sub-Boards-I & II) &

3 10004162 Emergency Lighting Board as per Specn. & Drawing as set 2,82,000
detailed below.
i) ' F1' Type Module with a rating of 630 A - 2 Nos.
ii) ' F1 (BC) ' Type Module with a rating of 630 A - 1 No
iii) ' F1' Type Module with a rating of 63 A (ACB) - 16
Nos.
iv) ' F1' Type Module with a rating of 125 A - 4 Nos.
v) ' V2' Type Module with a rating of 0-500 V - 3 Nos.
vi) ' F1' Type Module with a rating of 125 A - 1 No.
vii) ' F1' Type Module with a rating of 32 A - 4 Nos.
viii) Cost of the panel with all other required accessories
etc. as per specification - 1 set

ix) Cost of all Busbars, Cabling, Wiring meters etc. & all
other required accessories etc. as per specification - 1 set

E) INSTRUMENT TRANSFORMERS

Design, Engineering, manufacture, assembly, shop testing,

supply and delivery at site including packing forwarding
handling transportation to project site, unloading, of
420kV, 3000-2000-1000-500/1-1A, Single Phase current
1 10001158 No. 5,75,000
Transformers in accordance with specification, including
first fill of transformer oil and all accessories, auxiliaries
including marshalling boxes and terminal connectors for
CTs as specified 400kv technical specification.

Design, Engineering, manufacture, assembly, shop testing,

supply and delivery at site including packing forwarding,
handling at port of disembarkation, transportation to
project site, unloading, of 245kV, 40kA 1600-1200-800/1-
2 10001187 1-1-1-1A Single Phase Current Transformers in No. 2,80,000
accordance with specification, including first fill of
transformer oil and all accessories, auxiliaries including
marshaling boxes and terminal connectors for CTs as
specified in 400kv technical specification.

70
 File No.ENE51-PM0SYI(400)/12/2021-EE2
Rates without
SAP Material GST & F&I
Sl. No. Description Unit
Code (in Rs.)
2020-21
Design, Engineering, manufacture, assembly, shop testing,
supply and delivery at site including packing forwarding
handling transportation to project site, unloading, of
420kV Single Phase CVT in accordance with
3 10001300 No. 3,31,867
specification, including first fill of transformer oil and all
accessories, auxiliaries including marshalling boxes and
terminal connectors for CVTs as specified in 400kv
technical specification.
F) EARTHING AND EARTHMAT
Discharge rod 10 ft long with suitable screw type clamp
1 10006901 suitable for moose conductor & 15 Mtrs long 25 sqmm. Set 11,081
Copper lead with heavy duty crocodile clamp.
Electrical safety hand gloves suitable for the operation in
2 70004306 Set 2,719
400/220kV switchyard of ISI Quality.
2 Mtr x 1 Mtr, 10mm thick Neoprine Rubber mats of ISI
3 70004363 No. 2,786
Quality.
Stainless container of 2 litres capacity for collection of oil
4 10000650 No. 1,478
samples with cock arrangements at both ends.
70000511,
Electrical safety Belts, Shoes and Helmets suitable for the
5 70004303, Set 3,650
operation in 400/220kV switchyard of ISI Quality.
70004303
G) BUS BAR MATERIAL
1 10007505 400 kV Bus Post Insulators. Nos 40,074
2 10008687 220 kV Bus Post Insulators. Nos 22,204
4.5" IPS Aluminum tube of electrical grade including
3 10010128 Mtrs 2,842
welding sleeves.
4" IPS Aluminum tube of electrical grade including
4 10009058 Mtrs 2,332
welding sleeves.
Bay Marshalling Boxes for 400KV, 220 and 132 KV Bays
5 10009246 Nos. 49,278
with 3mm Aluminum sheet.
400 KV Single suspension hardware suitable for Twin
6 10007014 sets 6,500
Moose.
400 KV Double Suspension hardware suitable for Quad
7 10007009 Sets 7,500
Moose.
400 KV Double Tension hardware suitable for Twin
8 10007002 Sets 12,596
Moose.
400 KV Double Tension hardware suitable for Quad
9 10007005 Sets 20,000
Moose.
220 KV / 132kV Single suspension hardware suitable for
10 10007083 3,500
Twin Moose.
220 KV double suspension hardware suitable for Twin
11 10007073 Sets 4,500
Moose.
220 KV Double suspension hardware suitable for Quad
12 10007071 Sets 8,100
Moose.
220 KV / 132kV Double tension hardware suitable for
13 10007021 Sets 6,222
Twin Moose.
220 KV Double tension hardware suitable for Quad
14 10007020 Sets 12,616
Moose
15 10008085 400 KV Conductor Spacers for Quad moose Nos. 1,200
16 10008086 400 KV Conductor Spacers for Twin moose Nos. 450
17 10008096 220 KV Conductor Spacers for Twin moose Nos. 450
18 10008095 220 KV Conductor Spacers for Quad moose Nos. 1,000

71
 File No.ENE51-PM0SYI(400)/12/2021-EE2
Rates without
SAP Material GST & F&I
Sl. No. Description Unit
Code (in Rs.)
2020-21

19 400 kV clamps & connectors including jumper sleeves

(a) 10008040 BPI Clamp for Twin moose through/expansion type Nos. 1,209
(b) 10008698 BPI Clamps for 4.5" IPS Rigid /sliding /expansion type Nos. 2,363
(c) 10008041 BPI Clamps for 4" IPS Rigid /sliding type/expansion Nos. 2,304
(d) 10008042 T Connectors SM to SM Nos. 966
(e) 10008043 T Connectors TM to SM Nos. 1,527
(f) 10008032 Inter connector TM to 4.5" IPS Al. Tube Nos. 2,130
(g) 10008030 Inter connector QM to 4.5" IPS Al. Tube nos 4,260
(h) 10008037 Inter connector TM to 4" IPS Al. Tube 645
(i) 10008089 Corona spheroid Nos. 692
(j) 10008092 PG Clamps Moose to Moose Nos 510
20 220 kV /132kV Clamps & connectors
a) 10008026 BPI Clamp for Single moose Nos 702
b) 10008097 BPI Clamp for Twin moose through/expansion type Nos. 1,209
c) 10008098 BPI Clamps for 4" IPS Rigid/sliding/expansion type Nos. 2,304
d) 10008100 T Connector SM to SM Nos. 884
e) 10008931 T Connector TM to SM Nos. 1,284
f) 10008080 Isolator connecting Clamps suitable to Twin Moose Nos. 2,119
g) 10008102 Corona spheroid Nos. 692
h) 10008103 PG Clamps Moose to Moose Nos. 480
i) 10008101 Inter connector TM to 4" IPS Al. Tube Nos. 1,124
j) 10008761 Inter connector QM to 4" IPS Al. Tube Nos. 2,267
Pad type Compressor clamp for GS Earth wire to 75 x 12
21 10008105 Nos. 147
Flat
22 10008106 Cleat type clamp for G.S Earth wire Nos. 70
23 10008104 T clamp for GS Earth wire with flexible jumpers Nos. 300
H) POWER AND CONTROL CABLES

Design of complete cabling system for the entire

substation, preparation of cable scheduling , manufacture,
shop testing, packing and forwarding , transportation to
site/stores, providing conduits,cable termination kits,
cable lugs and glands of the following Power & Control
Cables as per requirement.

Single core, 630 [Link], 1100 V XLPE, FRLS insulated

1 10003381 PVC sheathed, Aluminium wire/strip armoured, stranded Km 5,87,337
aluminium conductor cable.
Single core, 300 [Link], 1100 V XLPE, FRLS insulated
2 10003383 PVC sheathed, Aluminium wire/strip armoured, stranded Km 3,09,098
aluminium conductor cable.
3 ½ core 300 [Link], 1100 V, XLPE, FRLS insulated
3 10003385 PVC sheathed, galvanized steel wire / strip armoured, Km 9,61,838
stranded aluminium conductor cable.
1100 V, PVC, FRLS insulated PVC sheathed, galvanised
4 steel wire / strip armoured, stranded aluminium conductor
cable.
(a) 10003391 3.5 core, 35 [Link]. Km 1,79,773
(b) 10003392 4 core, 16 [Link]. Km 1,06,615
(c) 10003395 4 core, 6 [Link]. Km 79,235
(d) 10003396 2 core, 6 [Link]. Km 56,624
1100 V, PVC, FRLS insulated PVC sheathed, galvanized
5 steel wire / strip armoured, stranded copper conductor
cable

72
 File No.ENE51-PM0SYI(400)/12/2021-EE2
Rates without
SAP Material GST & F&I
Sl. No. Description Unit
Code (in Rs.)
2020-21
(a) 10003299 3 core 2.5 [Link]. Km 98,599
(b) 10003221 5 core 2.5 [Link]. Km 1,13,092
(c) 10003300 7 core 2.5 [Link]. Km 1,50,929
(d) 10003278 10 core 2.5 [Link]. Km 1,89,000
(e) 10003280 14 core 2.5 [Link]. Km 2,52,683
(f) 10003281 19 core 2.5 [Link]. Km 3,33,452
(g) 10003597 27 core 2.5 [Link]. Km 4,87,770
(h) 10003210 50 Sq. mm Multistrand
Galvanized flexible
cable trays with 2mm copper
thick cable
perforated CRCA Mtrs
6
sheet
(a) 10003603 200 mm size Mtrs 393
(b) 10003531 450 mm size Mtrs 659
7 GI Pipe for entry into cable trench
(a) 10003548 4" Dia 3 mm thick GI Pipe Including Sacials, Bends etc., Mtrs 632

(b) 10003549 6" Dia 3 mm thick GI Pipe Including Sacials, Bends etc., Mtrs 895
I) INDOOR & OUTDOOR ILLUMINATION
1 Indoor Lighting Fixtures.
Control room lighting fixtures -make-CGL-LCBOR-40-
(a) Nos 4,000
CDLor equivalent model in Philips/Bajaj.

Decorative Pendent mounting lighting fixtures make-CGL-

(b) Nos 7,000
LCLR66-60-CDL or equivalent model in Philips/Bajaj.

Pendent mounting lighting fixtures -make CGL-LCLP54-

(c) Nos 4,800
36-CDL or equivalent model in Philips/Bajaj.
Lighting fixtures-make CGL-LHBL-60-CD or equivalent
(d) Nos 5,000
model in Philips/Bajaj.
Lighting fixtures-make CGL-LPLLA-18-CDL or
(e) Nos 699
equivalent model in Philips/Bajaj.
1 x 11W CFL lamp Emergency light with Battery operated
portable fixtures with built in chargeable batteries and
(f) Nos 900
battery charger suitable for a lighting period of six hours
of make Bajaj/Philips/CGL/BPL.
Decorative type lighting fixures with 4 Nos 18 watts CFL
(g) Lamp for Portico, main gate etc, make Bajaj / Philips / Nos 1,800
CGL are equivalent.
Wireless Buzzer anchor make or equivalent approved
(h) Nos 100
make with ISI mark.
Following items for providing and fixing concealed in
roof and walls with PVC Conduit piping of ISI standards
2 with necessary GI wire of suitable guage to draw wires at
later date including cost of junction boxes [Link] and
conveyance of all materials.
a) 10009106 40 mm dia - 2mm thick Mtrs 76
b) 10011978 32mm dia - 2mm thick Mtrs 76
c) 25mm dia - 2mm thick Mtrs 66
d) 10011982 12mm dia - 1.5mm thick Mtrs 45
Indoor Modular Main distribution board suitable for wall
insert with 1No 63A TP MCB for I/C and 6 Nos 32A
3 10009303 SPMCB, 8 Nos 10 A SPMCB & 10 Nos 16A SPMCB Nos 8,562
with neutral link for O/G complete make Havells
/LEGRAND or MDS or equivalent.

73
 File No.ENE51-PM0SYI(400)/12/2021-EE2
Rates without
SAP Material GST & F&I
Sl. No. Description Unit
Code (in Rs.)
2020-21

AC Distribution Boards Mains for usage in AC Kiosks for

4 10004170 supply (indoor wall inserted/mounted) with SP 16A Nos 19,834
MCBs - 3 Nos., 6A SP MCBs-2Nos., 2A SP MCBs 3 Nos.

Decorative Type Ten panel Switch boards in AC Kiosks

5 10009466 with 5A switches - 5/ 7 Nos.& 5/15A plug-1 No with 1 Nos 18,141
No 15 A Switch.(Anchor/Havels)
6 Out Door street Lighting Fixtures
Street lighting fixtures -make CGL-LSTN1-150-CDL-A or
a) 10009389 Nos 7,500
equivalent model in Philips/Bajaj
Decorative Post Lantern-make CGL-LPTO-60-CDL/M or
b) Nos 6,000
equivalent model in Philips/Bajaj.

Lighting Masts / Poles with junction boxes, earthing

7
materials and all accessories as per drawing enclosed.
a) Type A1 with junction box Nos 11,896
b) Type E1 with junction box Nos 6,366
10009407 Lighting Panels for Control house
8 I/C 63A TPN SFU - 1 No. Nos 13,336
O/G 16A-32A SPMCB - 24 Nos.
Outdoor Junction Box with 32A-SP-MCB-2 Nos,10A-SP-
9 10009434 MCB-4 Nos & terminal blocks (bolt type) for 6 circuits Nos 4,868
and neutral link.
415V, 63A - Interlocked Switch and Socket outdoor
10 10009412 Nos 3,316
Power Recepticle.
Decorative Type Six panel Switch boards with 5A
11 10009465 switches - 5 Nos., 5 & 15A plug-2 No with 2 No 15 A Nos 1,084
Switch.(Anchor/Havels).
Decorative Type Ten panel Switch boards with 5A
12 10009466 switches - 7 Nos., 5 & 15A plug-3 Nos with 3 No 15 A Nos 1,248
Switch.(Anchor/Havels).
Decorative Type Three panel Switch boards with 5A
13 10009444 Nos 569
switches - 3 Nos, 5A Plug - 1No(Anchor/Havels)
Decorative Type Three panel Switch boards with 15A
14 10009445 Nos 952
switches - 2 Nos.&15A plug-2 No .(Anchor/Havels)
15 Telephone Junction Boxes
MDF box suitable for 50 pair Telephones with crones and
(a) 10010965 Nos 1,958
surge protection complete.
MDF box suitable for 10 pair Telephones with crones and
(b) 10010967 Nos 1,460
surge protection complete.
(c) 10011014 Single socket outlet comprising RJ-45 Socket. Nos 181
(d) 10011015 Dual socket outlet comprising RJ-45 Socket. Nos 324
1400 mm sweep ceiling fans with Electronic regulator
16 10009418 Nos. 1,081
CGL/Bajaj/Usha/Khaitan make.
Wall mounted Fans with 400 mm sweep with Electronic
17 10009346 Nos. 2,147
regulator CGL/Bajaj/Usha/Khaitan make.
Outdoor AC Distribution Board with 2 Nos Incomings, 3
Phase, 440 V, 300 Amps, with Cu Bar and 300 Amps
18 10004152 Fuse units & Neutral link complete and outgoing 2 Nos , No. 32,441
3P, 125 A, MCBs including all accessories including CT
meter arrangement (200/1 ratio).
19 10009420 Wheel Mounted ladders (10 Mtrs Height) No. 20,937
20 70000965 Aluminium ladders (12ft Height) No. 10,741
21 70000977 Telescopic aluminium ladder (18feet) No. 24,696

74
 File No.ENE51-PM0SYI(400)/12/2021-EE2
Rates without
SAP Material GST & F&I
Sl. No. Description Unit
Code (in Rs.)
2020-21
22 70000966 Aluminium ladders (8ft Height) No. 8,341
AIR CONDITIONING AND VENTILLATION
J)
SYSTEM
A Air Conditioning.

Wall mounted Split air conditioners 2.0 Ton capacity with

cooling capacity of 24000 BTU/Hr & 6000 [Link]/Hr with
1 10009818 No. 43,268
stabilisers, receptacles including all support structures and
all other accessories with MCB of 25KA--.5 star model

Under deck insulation for the roof exposed to sunlight

2 10009869 with 50 mm thick TF quality expanded poly styrene Sft 361
including GI washers and wire for fixing.
B Ventilation
Supply of exhaust fans of propeller type/ axial type, each
1 with a suitable drive motors, DOL starters, vain protection
with screen, grouting bolts etc.,.
3ph, 24" Sweep 1440 RPM, 3000 cum/hr, exhaust fan or
a) 10009835 Nos. 4,274
equivalent with 3- ph MCBs.
3ph, 18" Sweep 960 RPM, 2000 cum/hr, exhaust fan or
b) 10009836 Nos. 3,990
equivalent with 3- ph MCBs.
3ph, 12" Sweep 960 RPM, 500 cum/hr, exhaust fan or
c) 10009837 Nos. 2,170
equivalent with 3- ph MCBs.
K) DIESEL GENERATOR SET
DG Set 250 KVA (with acoustic insulation), 1500 RPM,
0.8 PF, 415 V, 3 phase, 50 Hz with the following :-

(1) Diesel Engine complete with all accessories as

specified.
(2) Alternator directly coupled to the engine through
coupling complete with all accessories.
(3) Automatic voltage Regulator.
(4) Complete starting arrangement including two Nos.
Batteries & chargers and Power and Control Cables and
cable glands and lugs etc.
(5) Base Frame and Foundation bolts.
(6) Day Tank of 990 litre capacity with all the accessories
and fittings.
(7) Oil pump for transferring to Day Tank as per
specification.
(8) Engine cooling and Lubricating system.
1 10009973 (9) Engine Air filtering System. set 13,62,006
(10) Exhaust silencer package with flexible coupling and
thermal Insulator.
(11) Set of GI Pipes, Valves, Strainers, unloading hose
pipes as required.
(12) All lubricants, diesel oil, consumables, touch up
paints etc, for the first filling, testing & commissioning at
site.

(13) AMF panel for Control & Metering, and alarm as per
specification including all power and control cables, with

cable glands & lugs etc suitable to Substation Automation

System.

75
 File No.ENE51-PM0SYI(400)/12/2021-EE2
Rates without
SAP Material GST & F&I
Sl. No. Description Unit
Code (in Rs.)
2020-21
(14) Acoustic insulation for DG Set as per the norms of
Central Pollution Control Board.
(15) All the equipment/material required for
control/monitoring of DG set through Sub-Station
Automation System.
FIRE PROTECTION, DETECTION & ALARM
L)
SYSTEMS

(a) Horizontal centrifugal Electric Driven Hydrant/HVW

Spray, pump of capacity 410M3/hr and total dynamic
head of 88MWC with all accessories & fittings - 1 No.
1 10009618 Set 7,45,000
(b) Electric Induction Motor Squirrel cage type for the
above with all accessories & fittings as per specifications -
1 No.
(a) Horizontal centrifugal Diesel Engine Driven
Hydrant/HVW spray pump of capacity 410M3/hr and total
dynamic head of 88MWC with all accessories and
[Link] the HVW pumps, one motor driven and one
diesel driven shall be of same model and their components
interchangeable - 1 No.
2 10009617 (b) Diesel Engine, multi cylinder type, four stroke cycle Set 9,18,500
with mechanical airless injection cold starting type for the
above with all accessories and fittings as per specification -
1 No.
(c) Set of Batteries - 2 Nos.
(d) Fuel tank having capacity to hold fuel oil for six hours
of full load run - 1 No.
(a) Horizontal centrifugal Electric Driven jockey pump of
capacity 10.8 m3/hr and Total dynamic head of 88MWC
3 10009619 with all accessories and fittings. Sets 1,80,782
(b) Electric Motor for the above with all accessories and
fittings as per specification.
Air vessels with vent valves etc. as per specification and
4 10009620 No. 3,28,864
system requirement.
Sump pumps of capacity 10M3 /hr. MWC with motor
5 10009621 Nos. 38,133
starter and all accessories.
6 10009629 Basket strainer 300 NB. Nos. 1,19,500
Control panel equipped with all accessories for motor
drives of Fire water pumps and 2 Nos. jockey pumps as
7 10009605 Set 1,95,800
per specifications suitable for 2 sources supply and 2 Nos.
Battery chargers.
Control Panel for Diesel Engine driven fire water pumps
8 10009607 Set 1,88,400
as per specification.
(a) Annunciation panel at fire water pump house as per
9 10009613 Set 1,79,800
specification.
(b) Annunciation panel in Control Room as per
10009614 Set 1,36,188
specification..
Supply of the following Hydrant and HVWS system
10
Accessories
a) 10009134 Single headed Hydrants. Nos. 10,836
b) 10009135 Landing Valves. No. 4,684
c) 10009033 Hose cabinets. Nos. 5,418
d) 10009034 Hoses of 15.0m length with coupling. Nos. 4,576
e) 10009035 Hoses of 7.5m length with coupling. Nos. 3,487

76
 File No.ENE51-PM0SYI(400)/12/2021-EE2
Rates without
SAP Material GST & F&I
Sl. No. Description Unit
Code (in Rs.)
2020-21
f) 10009036 Branch pipe with Nozzles. Nos. 3,050
Supply of the following Mild steel black pipes and
11
Mild steel galvanized pipes as per specifications
a) 10009037 300 NB Mtrs 3,940
b) 10009038 250 NB Mtrs 3,365
c) 10009039 200NB Mtrs 1,998
d) 10006447 150NB Mtrs 1,880
e) 10009084 100NB Mtrs 1,560
f) 10009085 80NB Mtrs 1,080
g) 10009074 50NB Mtrs 840
h) 10009075 25NB Mtrs 241
i) 10009076 15NB Mtrs 171
Set of GI & MS Piping beyond deluge valves for
12 10006448 transformer including detection piping and pipe supports Sets 2,45,900
including all accessories complete.
13 Supply of the following valves :-
a) 10006450 300 NB Gate Nos. 34,336
b) 10006451 250 NB Gate Nos. 33,408
c) 10009136 250 NB Check Nos. 21,344
d) 10009137 200 NB Gate Nos. 26,912
e) 10009138 150 NB Gate Nos. 14,848
f) 10009139 100 NB Gate Nos. 15,222
g) 10009140 80 NB Gate Nos. 12,399
h) 10009141 80 NB Check Nos. 10,208
i) 10009142 50 NB Gate Nos. 7,109
j) 10009143 50 NB Check Nos. 4,176
k) 10009144 25 NB Gate Nos. 2,320
l) 10009009 15 NB Gate Nos. 1,763
m) 10009145 Float operated valve 100NB Nos. 21,344
14a) 10009146 Float operated Level guage Nos 14,466
14b) 10009147 Level switch Nos 18,920
15 10009148 Pressure Gauge Nos 1,720
16 10009149 Pressure Switch Nos 4,902
17 10009150 Differential Pressure Gauge Nos 3,143
Deluge valve with motor gounge, pr. switch, [Link],
18 10009151 Sets 98,563
solenoid valve to drain - size 150 NB
19 10009615 Local control panel for Deluge valve Nos. 12,345
20 10009616 Strainer Y type, 150 NB Nos. 25,817
21 10009622 Quartzoid bulb detectors Nos 530
22 10009623 HVW spray nozzles Nos 1,290
Supply of Detection and Alarm system including all
23
hardware and all other accessories
a) 10006637 Multi criteria detectors Nos 2,911
b) 10009626 Heat detector Nos 2,467
c) 10009627 Response indicator Nos 263
d) 10009628 Manual call point Nos 1,655
Fire detection & Alarm panel for control room with 2 Nos
hooters, 2 Nos. sirens and 2 Nos. relay modules with RS-
e) 10009604 Set 1,15,427
485 communication port & all accessories for integrating
in SAS.
Water pressure transducer with input of 0-16 bars and
f) 10010267 with 2nos ports as output of range 4-20mA for integrating Nos 63,692
in SAS.

77
 File No.ENE51-PM0SYI(400)/12/2021-EE2
Rates without
SAP Material GST & F&I
Sl. No. Description Unit
Code (in Rs.)
2020-21
Temperature transducer in control room for measuring
ambient temperature with input of 0-75 degree centigrade
g) 10010267 Nos 43,399
and with 2nos ports as output of range 4-20mA for
integrating in SAS.(CR-1, ACK-10)
Supply of the following Portable Fire Extinguishers
24
with all accessories as per specification
Dry chemical powder type Fire extinguishers of 9 kgs.
a) 10009711 Nos 2,173
Capacity.
Dry chemical powder type Fire extinguishers of 25 kgs.
b) 10009712 Nos 10,718
Capacity (trolley mounted).
Dry chemical powder type Fire extinguishers of 50 kgs.
c) 10009713 Nos 14,384
Capacity (trolley mounted).
Dry chemical powder type Fire extinguishers of 150 kgs.
d) 10009714 Nos 39,600
Capacity (trolley mounted).
CO2 type portable Fire extinguishers of 45 kgs. Capacity
e) 10009726 Nos 32,400
(trolley mounted).
CO2 type portable Fire extinguishers of 22.5 kgs.
f) 10009725 Nos 15,266
Capacity (trolley mounted).
CO2 type portable Fire extinguishers of 9 kgs. Capacity
g) 10009724 Nos 8,352
(trolley mounted).
h) 10009719 CO2 type portable Fire extinguishers of 2 kgs. Capacity. Nos 3,434

i) 10009735 9 liters capacity Mechanical foam type fire extinguishers. Nos 2,691
j) 10009715 Sand / water Buckets 9 liters capacity with stand. Nos 360
Fire Alarm Panel for the above detectors with 24V
25 10009602 Nos. 3,663
(12+12) Batteries for supply to be installed in AC Kiosk
26 Mandatory spares
a) 10009044 Self starter of HVW Pumps No 42,484
b) 10009046 Fuel oil filter elements of Diesel engine drive No 12,017
c) 10009048 Gland packing of jockey pumps No 6,117
d) 10009622 Quartzoid bulb detector Nos 530
e) 10009049 Projectors (Nozzles) Nos 1,285
f) 10009626 Heat detectors No 2,384
g) 10009149 Pressure switch No 6,941
h) 10009154 Flaps for check valves 250NB Nos 13,367
i) 10009153 Flaps for check valves 80NB Nos 4,046
j) 10009152 Flaps for check valves 50NB Nos 6,521
k) 70003320 Set of bearings for HVW pumps Set 9,755
l) 70003321 Set of bearings for Jockey pumps Set 5,562
m) 10009148 Pressure Gauge No 2,780
M) 33kV STATION POWER SUPPLY FACILITIES
33kV/433V, 630 KVA Station supply transformers with
1 10000702 Nos. 5,90,393
all accessories and fittings as per specifications.
2 10009247 HT Trivector Meter box. Nos. 6,128
3 10000712 33 KV HG Fuse sets with Insulators. Km 12,845
150 x 150 mm RS Joists, MS channels &Misc. Structural
4 10012509, Steel for 33KV Switchyard CT`s, LA`s, PT`s, CB`s, Nos. 69,472
Isolators & HG Fuse sets.
Hard ware, Clamps, connectors, galvanized bolts, nuts and
washers and other miscellaneous items required for
5 10007320 Nos. 1,08,142
complete erection and commissioning of 33 KV /433 V
facilities as per the specification.

78
 File No.ENE51-PM0SYI(400)/12/2021-EE2
Rates without
SAP Material GST & F&I
Sl. No. Description Unit
Code (in Rs.)
2020-21
33 kV CTs with junction box and terminal connectors and
6 10001112 Sets 16,691
all accessories as per specification, 25-15/1-1-1A.
CONTROL HOUSE FURNITURE AND
N)
MONITORING SYSTEM
Godrej make Tables (Model EARL Size 200 W x 1900 D
1 70002812 x 750H mm) or Wipro make (Model Kingsley Premium No. 6,353
Type-A main table).
Credenzas for above (Make Godrej, Model: EARL Size
2100 W x 350D x 1520H) or Wipro make, Model
2 70002813 Wudsafe-LHS:size 750Lx425Dx740HT or equivalent as No. 1,995
per approval of APTRANSCO M/s. Godrej make with
revolving chair.
Self Containing 12 Nos Racks with safety locker make
3 70002727 Set 16,556
Godrej or Wipro or equivalent.
Junior Executive table (1365 x 680 x 7350) mm with
4 70002591 decolam Model No.T-9 make Godrej or Wipro or Nos. 8,982
equivalent.
Steel Table (1199 x 590 x 735) mm with single drawer
5 70002589 and Decolam Top Model. T-111 make Godrej or Wipro or Nos. 5,399
equivalent.
Steel revolving chair model No. CH - 1014 with heavy
6 70002668 base seat and back in cane make Godrej or Wipro make Nos 5,182
model: That's it or equivalent.
Steel Tubular `S Type chair (Continuous Arm) Model No.
Chr-7 in 1" dia and 14 gauge pipe, cane seat and back in
7 70002669 Nos 3,000
teak wood with quality cane make Godrej or Wipro make
model: That's it or equivalent.
Steel Tubular `S` Type chair (without arm) Model No. Chr-
4 in 1" dia and 14 SWG pipe, cane seat and back in teak
8 70002666 Nos 2,289
wood with quality cane make Godrej Wipro make model:
That's it or equivalent.
Steel store well plain (900 x 507 x 1950) mm Make
9 70002711 Godrej, Model: Slimline 4S Text purple colour or Wipro Nos 7,440
make model Endura.
10 70002787 Plastic file trays ( 16'' x 11''x3'') Nos 266
Steel Stools (15''x15"x18") with MS top sheet thickness
11 70002703 20mm 1" square pipe 16 gauge make Godrej or Nos 1,120
equivalent.
12 70002788 Steel waste paper baskets (12"x10"x10") Nos 465
Steel rack (6'x3'x16") with 6 shelves making 5
13 70002726 Nos. 2,800
compartments (22 Gauge)
14 70002745 Short bench (4'x14"x1/2') with laminated Top. Nos. 3,360
15 Display Board for Substation Layout
6' x 5' Plywood Novapan finish with suitable border and
computerized symbols, labels etc of single line diagram as
a) 70002814 No. 4,687
directed by Site Engineer complete suitable for Wall/Floor
stand mounted.
b) 70002815 Aluminium Floor stand for the above. No. 8,652
3' x 2' Wooden key board suitable for holding 30 Nos Key
16 70002816 No. 1,081
chains
Brother P-Touch Sticker lable printer with Software and
17 70001850 No. 14,587
all accessories (Model PT-2700) / Latest Model.
Sticker lables, printer cartridges suitable for (Brother
18
P make) Touch sticker Lables, Printer.

79
 File No.ENE51-PM0SYI(400)/12/2021-EE2
Rates without
SAP Material GST & F&I
Sl. No. Description Unit
Code (in Rs.)
2020-21
a) 70001851 24 mm size. No. 396
b) 70001852 18 mm size. No. 325
c) 70001853 12 mm size. No. 252
Supply and fixing of teak wood name boards with enamel
19 70004318 Nos. 3,174
painting letters of size 12"x4" for rooms in control room.

Supply and fixing of Bay Indicator boards of thickness

20 70002817 18" with MS sheet and MS angles of size 10"x26" Nos. 1,992
including cost of letters.

Supply and fixing of name board indicating 400/220kV

SS, APTRANSCO, XXXXXXXXX, XXXXXXXX Dist.
21 70004411 Of size 4x8 feet with MS 18gauge sheet MS Nos. 19,628
1.5"angles.1.5"pipes and concreting foundation including
cost of painting letters(1no. In English & 1no. In Telugu).

22 70004412 Supply and fixing of notice board of size 2x2.5feet. No. 724
23 70004414 Pictograph of size 2x4feet with letters. No. 5,429
24 Personal computer (with the following configuration)

Intel core i-7-3920XM Process 512KB level-8M cache

upto 3.80 GHz, 8GB RAM , 128bit graphic accelerator
with 4MB SG RAM,160GB Ultra DMA-HDD,1.44MB
FDD,52X Creative DVD-ROM,1x16550 fast serial ports
& IEPP ECP parallel ports , 4X, universal serial bus
(USB) ports, PS/2 compatible key board/mouse ports, 19"
a) 70001915 Nos. 67,712
colour monitor, Internet ready multimedia key board,
Optical scroll mouse and built in modem 128KBPS along
with telephone instrument & other accessories and
complete installation of the system, DVD writer with
latest software. (HP / ACER make or equivalent reputed
make
b) 70001867 10/100 MBPS Ethernet Card Nos. 24,449

Windows-10 or later version of OS and latest MS OFFICE

c) 70005269 software - preloaded along with Media & Manuals, Power Nos. 32,589
management software, ACPI and windows 10 / Latest.

Latest updated versions of Antivirus software kit - Norton,

d) 70005258 Nos. 8,468
macfee, hill view etc alongwith Media & Manuals
e) 70001982 Pen drives of 128GB of latest version Nos. 1,278
25 70002246 HP laser jet printer 101 0 to 1015 series.(1020 series) 13,974
Laser Jet Printer with Fax, scan, photostat along with 2
26 70002240 Nos. 27,791
sets of Spare cartridges and Scanner.
27 70002092 2 kVA inverter (input 220V DC, output 220V AC) Nos. 17,564
Laptop of latest version with all software, multimedia and
28 70001712 Nos. 51,283
manuals of make Dell or equivalent etc.
29 70005310 Latest AutoCAD software licensed copy No. 34,928
30 70000505 Binoculars(latest version) No. 4,357
Xerox Machine (RICOH Digital Multi Functional
Network Device Model MP 2001 SP / Latest model with
31 70001856 Nos. 1,05,000
RADF Network, Printer, Scanner, Fax Option (LP Printer
latest version with 2Nos Spare cartridges)
32 70004448 Water -Purifier ISI standard make. Nos. 9,739

80
 File No.ENE51-PM0SYI(400)/12/2021-EE2
Rates without
SAP Material GST & F&I
Sl. No. Description Unit
Code (in Rs.)
2020-21
Furniture consisting of a table and revolving chair for PC
33 Nos. 6,810
and a table for printer
O) 400KV LINE MATERIALS
1 67500060 Number plates with Bolts &Nuts and Washers No 151
2 67500052 Danger plates with Bolts &Nuts and Washers No 168
3 67500058 Phase plates with Bolts &Nuts and Washers(Set of Three) Sets 199

4 67500055 Circuit plates with Bolts &Nuts and Washers (Set of Two) Sets 240
5 Anti climbing devices
a) 67500033 Tangent towers Nos 3,920
b) 67500034 Small angle towers Nos 5,227
c) 67500035 Medium angle towers Nos 6,533
d) 67500036 Large angle towers Nos 6,533
6 67500042 Bird guards(saw tooth ) Nos 200
7 Earthing of the towers
a) 10006927 Pipe type Earthing Sets Sets 1,271
b) 10003006 Counter poise earthing Sets 3,049
Insulator Hardware & Accessories for conductor and
8
earth wire.
(a) For Quad Moose ACSR conductor
Double Suspension Hardware for Quad ACSR Moose
i) 10007009 Sets 9,897
Conductor
ii) 10007001 Quadruple tension Hardware for ACSR Moose conductor Sets 37,000

iii) 10007011 Pilot string Hardware for Quad ACSR Moose conductor Sets 10,293

iv) 10007274 Quadruple spacer dampers for ACSR Moose Conductor No. 1,373
v) Bundle spacers for ACSR Moose conductor No. 277
Rigid spacers (Quadruple ACSR Moose conductor) for
vi) 10007319 No. 1,027
jumpers.
vii) 10007201 Mid span compression joints for ACSR Moose conductor No. 841
viii) 10007218 Repair Sleeves No. 346
(b) For Twin Moose ACSR conductor
i) 10007027 Double tension Hardware for ACSR Moose conductor Sets 10,020
Double 'I' Suspension Hardware for ACSR/ INVAR
ii) 10007010 Sets 11,071
Moose Conductor
Single Suspension Hardware for ACSR/ INVAR Moose
iii) 10007083 Sets 6,000
Conductor
Single Suspension Pilot string Insulator Hardware for
iv) 10007501 Sets 10,293
Twin Moose ACSR Conductor complete
v) 10007276 Vibration dampers for ACSR Moose Conductor No. 903
Rigid spacers (Twin ACSR Moose conductor) for
vi) 10008569 No. 707
jumpers.
vii) 10007275 Spacer Dampers for ACSR Moose conductor No. 938
(c) For 7/3.65 mm GSS Earth wire
(i) 10007112 Suspension clamps for HTGS Earth Wire Sets 423
(ii) 10007063 Tension clamps for HTGS Earth Wire Sets 418
(iii) 10007279 Vibration dampers for HTGS Earth wire Nos 370
(iv) 10007210 Mid span compression joints for earth wire Nos 220
(v) 10006923 Flexible copper bonds for earth wire. Nos 510
(vi) 10007228 Repair Sleeves Nos 148

81
 File No.ENE51-PM0SYI(400)/12/2021-EE2
Rates without
SAP Material GST & F&I
Sl. No. Description Unit
Code (in Rs.)
2020-21
High Tension Galvanized Stranded Steel Earth wire
P) 10010175 KM 41,012
7/3.66 mm
Q) INSULATORS
120KN Disc Insulators (Antifog type with Zinc Sleeve)
(a).i 10007510 No. 510
460mm creepage
120kN Long Rod Insulators(one set= 23 No.s Disc
ii. 10007523 Set 16,338
insulators
iii. 10007601 120KN SRC Insulators -13020mm creepage No. 4,800
160KN Disc Insulators (Antifog type with Zinc Sleeve)
(b).i 10007508 No. 1,030
470mm creepage
160kN Long Rod Insulators(one set= 24 No.s Disc
ii. 10007524 Set 18,419
insulators
iii. 10007600 160KN SRC Insulators -13020mm creepage No. 5,835

82
 File No.ENE51-PM0SYI(400)/12/2021-EE2

TELECOM EQUIPMENT/MATERIAL RATES

Ex-Works Price
without GST and
[Link] SAP Code Category Description Units F&I (in
Rs)
SRR-2020-21
1 10011407 OPGW OPGW 24 Fiber capacity DWSM type cable Km 98,714

2 10011470 OPGW OPGW 48 Fiber capacity DWSM type cable Km 1,30,831

Suspension Assembly (Grounding clamps are part
3 10011420 OPGW Set 3,610
of suspension assembly)
Tension Assembly (Dead end Clamps and
4 10011423 OPGW Set 3,339
Grounding clamps are part of Tension Assembly)
5 10011422 OPGW Vibration Dampers No. 928
6 10011479 OPGW 24 F& 48F Splice Box (OPGW - OFAC) No. 5,158
7 10011482 OPGW 24 F& 48F Splice Box (OPGW - OPGW) No. 5,158
8 10011473 OPGW 48F 3 way Splice Box (OPGW-OPGW-OPGW) No. 16,415
9 10011421 OPGW Down Lead Clamps No. 336
Fibre optic cable of ADSS type with DWSM, 24
10 10011442 ADSS Km 1,00,158
fibre capacity.
10011461
Suspension clamp sets (grounding clamps are part
11 10011471 ADSS Set 5,123
of suspension assembly)
10011462 Tension clamp sets(dead end clamps and grounding
12 ADSS Set 5,544
10011472 clamps are part of tension assembly)
13 ADSS Splice boxes (ADSS-OFAC) No. 8,782
14 10011431 ADSS Splice boxes (ADSS-ADSS) No. 8,782
15 10011459 ADSS Vibration Dampers Assembly No. 1,049
10011464
16 10011469 UG-OFC UG [Link] unarmoured 48 F DWSM type Km 85,400

17 10011469 UG-OFC UG [Link] armoured 48 F DWSM type Km 89,000

18 10011408 UG-OFC UG [Link] armoured 24 F DWSM type Km 60,534

19 10011432 UG-OFC Splice boxes 24 F U/G (Joint closures) No. 6,311

20 10011432 UG-OFC Splice boxes 48 F U/G (Joint closures) No. 6,500

21 10011971 UG-OFC HDPE DUCT of 40/33 mm dia of standard Make km 65,381
RCC Chambers (120/76/5)cm W/L/T with base and
22 10011972 UG-OFC Each 6,771
top plates for every 0.5 Km
Uni directional short haul PDH type 8 Mbps
23 10011826 OLTE capacity OLTE equipment with primary MUX and No. 3,36,494
MDF
24 10011590 OLTE Spares for OLTE and MUX of PDH Set 1,68,247
Two directional Managed Synchronous Digital
Hierarchy (SDH) type, long haul which can drive
25 10011584 OLTE upto 320 Km in one direction and 280Km in No. 33,99,392
another direction, STM-4 upgradable to STM-16
OLTE with Primary Multiplexer.

83
 File No.ENE51-PM0SYI(400)/12/2021-EE2

Ex-Works Price
without GST and
[Link] SAP Code Category Description Units F&I (in
Rs)
SRR-2020-21

Two directional Managed Synchronous Digital

Hierarchy (SDH) type, Long Haul that can drive
26 10011594 OLTE No. 19,55,556
upto 240 Km in both directions, STM-4 upgradable
to STM-16 OLTE with Primary Multiplexer

Two directional Managed Synchronous Digital

Hierarchy (SDH) type, long haul which cxn drive
27 10011693 OLTE upto 180 Km in both directions, STM-4 No. 16,44,481
upgradable to STM-16 OLTE with Primary
Multiplexer
Two directional Managed Synchronous Digital
Hierarchy (SDH) type, long haul which can drive
28 10011592 OLTE No. 13,49,048
upto 150 Km in both directions, STM-4
upgradable to STM-16 OLTE with Primary
Multiplexer
Two directional Managed Synchronous Digital
Hierarchy (SDH) type, long haul which can drive
29 10011582 OLTE upto 120 Km in both directions, STM-4 No. 11,56,068
upgradable to STM-16 OLTE with Primary
Multiplexer.

Two directional Managed Synchronous Digital

Hierarchy (SDH) type, long haul which can drive
30 10011827 OLTE upto 120 Km in one direction and 60km in other No. 11,15,485
direction, STM-4 upgradable to STM-16 OLTE
with Primary Multiplexer.

Three directional Managed Synchronous Digital

Hierarchy (SDH) type, long haul which can drive
31 10011593 OLTE No. 14,56,311
upto 100 Km in all directions, STM-4 upgradable
to STM-16 OLTE with Primary Multiplexer.

Three directional Managed Synchronous Digital

Hierarchy (SDH) type, long haul in two directions
that can drive upto 100 Km in two directions and
32 10011586 OLTE No. 16,50,485
shot haul that can drive upto 60Km in one direction,
STM-4 upgradable to STM-16 OLTE with Primary
Multiplexer.

Two directional Managed Synchronous Digital

Hierarchy (SDH) type, long haul which can drive
33 10011589 OLTE No. 8,15,134
upto 60 Km in both directions, STM-4 upgradable
to STM-16 OLTE with Primary Multiplexer.

34 10011589 OLTE Spares for Long Haul OLTE and MUX Set 8,52,293
35 10011590 OLTE Spares for Short Haul OLTE and MUX Set 7,31,841
36 10011051 OLTE Digital Tele Protection Signalling equipment No. 2,04,576
37 10011692 OLTE Spares for Digital Tele Protection equipment Set 1,90,000
Fibre distribution panels for termination of Fibres of
38 10011692 OLTE No. 19,163
48 F capacity

84
 File No.ENE51-PM0SYI(400)/12/2021-EE2

Ex-Works Price
without GST and
[Link] SAP Code Category Description Units F&I (in
Rs)
SRR-2020-21
Fibre approach cable (DWSM) of 24 Fibre capacity
39 10011408 OLTE Km 98,000
with HDPE pipe
Fibre approach cable (DWSM) of 48 Fibre capacity
40 10011469 OLTE Km 1,08,000
with HDPE pipe
Laptop PC for configuration of remote OLTE,
41 10011640 OLTE MUX, Digital Teleprotection equipment with No. 54,818
necessary software
Fusion Splicing Machine (FSM) along with
42 70000317 OLTE No. 4,21,598
standard accessories
43 10012199 OLTE Opticall Time Domain Reflector (OTDR) No. 4,81,154
44 10004917 OLTE Optical Power Meter No. 91,334
45 10011802 OLTE Optical Laser Source No. 1,53,400
OFC tool kit consisting of Fibre stripping tool and
tools for cutting and stripping of sheathing, jacket
46 10011655 OLTE Set 1,86,295
armouring of OFAC/ADSS/OPGW cables
including two binoculars.
Network Management system for SDH and MUX
47 10011696 OLTE along with software and configuration tool ( PC- No. 13,82,633
1No, Chair- 1 No,Table-1No, Printer- 1 No)
SDH STM-4/16 analyzer with optical and electrical
48 10011694 OLTE No. 6,31,814
interfaces
Digital Access Cross Connect Switch (DACS) 16 x
49 10011694 OLTE 16 ports switching matrix, fully equipped for No. 1,10,503
minimum 16 E-1 ports
50 10011902 Cables 125 Ohms Co-axial Cable Km 99,104
51 10011919 Cables 6 pair PVC copper telephone Cable Km 37,637
52 10011925 Cables single pair PVC copper telephone Cable Km 7,111
53 10005696 Cables 25 Sqmm Battery cable Km 2,44,667
54 10003262 Cables 2.5 [Link], 2 Core Un-armoured Copper cable Km 35,900
55 10011965 Cables Cat 6 cable (305 mtrs each box) Box 5,654
20 pair Armoured jelly filled copper telephone
56 10011907 Cables Km 1,74,760
Cable
10 pair Armoured jelly filled copper telephone
57 10011913 Cables Km 73,713
Cable
Battery
58 10005230 48V/200Ah(1+0) Battery Set Set 62,400
Chargers
Battery
59 10005228 48V/250Ah(1+0) Battery Set Set 77,040
Chargers
Battery
60 10005551 48V/300Ah(1+0) Battery Set Set 88,200
Chargers
Battery
61 10005347 48V/400Ah(1+0) Battery Set Set 1,17,600
Chargers
Battery
62 10005326 48V/35A (1+0) Battery Charger No. 1,47,068
Chargers

85
 File No.ENE51-PM0SYI(400)/12/2021-EE2

Ex-Works Price
without GST and
[Link] SAP Code Category Description Units F&I (in
Rs)
SRR-2020-21
Battery
63 10005321 48V/50A (1+0) Battery Charger No. 1,55,614
Chargers
Battery
64 10005317 48V/100A (1+0) Battery Charger No. 1,96,105
Chargers
Battery
65 10010924 48V/150A (1+0) Battery Charger No. 2,33,000
Chargers

66 10010924 EPAX EPAX (16/16) with 2 E1 cards wired for 128 ports No. 1,45,777

67 10010926 EPAX Spares for EPAX (16/16) with E1 Set 53,333

68 10010952 EPAX EPAX (16/16), 128 universal ports fully wired No. 1,15,556
69 10010907 EPAX EPAX (8/8), 128 universal ports fullly wired. No. 86,666
70 10010939 EPAX Spares for EPAX Set 36,000
71 10010989 EPAX EPB Telephone No. 629
1.5 Ton 3 Star Split AC unit alongwith 4 KVA
72 10009812 AC unit Stabilizer including stand for outdoor unit and No. 40,258
copper kit with cable
2 Ton 3 Star Split AC unit alongwith 5 KVA
73 10009859 AC unit Stabilizer including stand for outdoor unit and No. 43,220
copper kit with cable
74 10005121 Tool Kit 4 1/2 Digit true RMS digital Multimeter No 33,192

Medium Size Tool kit 1)Screw Driver with

detachable bits (Taparia) 2) Spnner set 3) Cutting
Piller 4) No.e plier 5) Wire Stripper 6) 25Watt
75 10012175 Tool Kit No. 22,528
Soldering Iron 8)50 Watt Soldering Iron 8)
Crimping Tool 4/6/8 pin 9)3 1/2 Digit Multimeter
with briefcase
76 10010705 PLCC Single channel PLCC terminal ( 20 W) No. 1,16,349
77 10010701 PLCC Twin channel PLCC terminal ( 40 W) No. 2,33,042
78 10010720 PLCC Spares for single channel PLCC terminal Set 78,172
79 10010713 PLCC Spare set forTwin channel PLCC Terminal Set 1,81,567
80 10011058 PLCC Analog protection coupler No. 99,639
81 10011059 PLCC Spares for analog protection coupler Set 88,004
82 10011027 PLCC Digital protection coupler for DPLCC No. 2,06,623
83 10011053 PLCC Spares for digital protection coupler for DPLCC Set 1,53,660
84 10010709 PLCC Digital PLCC terminal No. 6,28,043

85 10010732 PLCC Spares for Digital PLCC terminal Set 4,80,077

86 10010738 PLCC Phase to Phase coupling unit No. 70,204

87 10010744 PLCC Phase to Ground coupling unit No. 41,291
2000A/1.0 mH Wavetrap along with pedestal
88 10010601 PLCC No. 5,20,062
mounting and insulator stack.

86
 File No.ENE51-PM0SYI(400)/12/2021-EE2

Ex-Works Price
without GST and
[Link] SAP Code Category Description Units F&I (in
Rs)
SRR-2020-21
1250A/0.5 mH Wavetrap along with mounting
89 10010605 PLCC No. 1,55,360
Pedastal and insulator stack.
630A/0.2 mH Wavetrap along with accessories
90 10010613 PLCC No. 1,01,315
suitable for suspension mounting.
91 70001996 PLCC FSK Modem No. 1,25,466
92 70001525 PLCC Earth Megger No. 13,988
93 10012151 PLCC Selective Level meter No. 3,06,800
94 10012162 PLCC Selective Level Oscillator No. 2,33,919

Motorola make, XIRP 8608i model walkie - talkies

(UHF Handheld Sets) Trunked radio, non-keypad &
Walkie
95 10012211 without Display, 806-870 MHz frequency, Li-on No. 19,800
talkie
High capacity battery of 1650 mAH , Belt Clip,
Antenna, Battery Charger & User Manual

Walkie Spare batterie 1650 mAH High capacity battery for

96 10012212 No. 3,000
talkie Walkie - talkies

97 EPAX EPAX(32/32) with 2 E1 cards wired for 128 ports No. 2,91,350
98 EPAX EPAX(32/32) 128 universally wired ports No. 2,32,570
spares for EPAX(32/32) with 2 E1 cards wired for
99 EPAX Set 83,393
128 ports

100 EPAX spares EPAX(32/32) 128 universally wired ports Set 70,624

87
 File No.ENE51-PM0SYI(400)/12/2021-EE2
Auto/ Power Transformers and Reactors Rates
Ex-Works Price
without GST
[Link]. SAP CODE Description of Transformer/Reactor Unit and F&I
(in Rs)
SSR-2020-21
500MVA, 400/220/33KV Auto Transformer with all
1 10000000 No. 16,61,42,952
accessories.
315MVA, 400/220/33KV Auto Transformer with all
2 10000001 No. 9,80,00,000
accessories.
160MVA, 220/132/11KV Auto Transformer with all
3 10000005 No. 5,90,60,000
accessories.
100MVA, 220/132/11KV Auto Transformer with all
4 10000007 No. 4,15,00,000
accessories.
80MVA, 220/33KV Power Transformer with all
5 10000009 No. 4,50,00,000
accessories.
80MVA, 132/33KV Power Transformer with all
6 10000023 No. 4,00,00,000
accessories.
50MVA, 220/33KV Power transformer with all
7 10000024 No. 3,32,45,763
accessories.
50MVA, 132/33KV Power transformer with all
8 10000010 No. 3,64,30,870
accessories.
31.5MVA, 132/33KV Power transformer with all
9 10000025 No. 1,80,00,000
accessories.
10 10012591 125MVAR, 400KV Shunt Reactor withh all accessories. No. 7,50,00,000

11 10000821 80MVAR, 400KV Shunt Reactor withh all accessories. No. 6,50,00,000

88
 File No.ENE51-PM0SYI(400)/12/2021-EE2

Control and Relay Panels along with SAS equipment for 400KV, 220KV AND 132KV
SUBSTATIONS

Ex-Works Price
without GST
[Link]. SAP Code Description of Equipment/ Material Unit and F&I
(in Rs)
SRR-2020-21

Design, engineering, manufacture, assembly, shop testing,

supply and delivery at sites including packing forwarding
handling and unloading at site of complete set of the
following control and relay and protection panels and
other equipment with all equipment accessories and others
as per APTRANSCO specification.

Common Control and Busbar Protection Panels for 400kV

1 10004002 side As per 400KV Specification for Control & Relay Nos 46,35,294
Panels.
Common Control and Busbar Protection Panels for 220kV
2 10004003 side As per 400KV Specification for Control & Relay Nos 30,05,200
Panels.
400kV Line CB Control and Relay Panels As per 400KV
3 10004004 Nos 4,35,555
Specification for Control& Relay Panels
400kV Line Protection Panels As per 400KV Specification
4 Nos 11,21,000
(without Line Reactor).
400kV Tie CB Control and Relay panels As per 400KV
5 10004007 Nos 5,72,492
Specification for Control & Relay Panels.
400kV side of 400/220kV 500/315 MVA ICT CB Control
6 10004013 and Relay Panels as per 400KV Specification for Control Nos 4,53,015
& Relay Panels.
400/220kV 500/315MVA ICT Protection Panels As per
7 10004014 Nos 9,51,145
400KV Specification for Control & Relay Panels.
220kV side of 400/220kV 500/315 MVA ICT CB Control
8 10004013 and Relay Panels as per 400KV Specification for Control Nos 4,53,015
& Relay Panels.
220kV Line CB Control and Relay Panels As per 400KV
9 Nos 4,65,782
Specification for Control & Relay Panels.
220kV Line Protection Panels As per 400KV Specification
10 10004022 Nos 8,34,037
for Control & Relay Panels.

220kV Bus Coupler Control, Relay and Protection Panels

11 10004023 Nos 5,56,996
As per 400KV Specification for Control & Relay Panels.

220kV Transfer Bus Coupler Control, Relay and

12 10004024 Protection Panels 400KV Specification for Control & Nos 4,79,935
Relay Panels.
132kV feeder Control, Relay and Protection panels with
13 10004047 IEC 61850 with Automation features as per 400KV Nos 6,84,746
Specification.

Sub-Station Automation System as per 400KV

14 10010251 Specification including Software for Sub-Station Nos 1,21,71,390
Automation System along with Visual monitoring system.

Relay Test kit and Testing Instruments as per 400KV

15 70001502 Nos 29,54,255
Specification for Control& Relay Panels.

89
 File No.ENE51-PM0SYI(400)/12/2021-EE2

Ex-Works Price
without GST
[Link]. SAP Code Description of Equipment/ Material Unit and F&I
(in Rs)
SRR-2020-21
125MVAR Bus Reactor Main CB Control & Relay Panel
16 10004011 Nos 6,05,000
as per 400KV Specification.
125MVAR Bus Reactor CB Protection Panel as per
17 10004009 Nos 9,56,432
400KV Specification.
Mandatory Spares for Control and Relay Panels as per
18 10004253 Lot 21,27,744
400KV Specification.
19 10004035 220 kV Feeder Control & Relay Panels with BCUs Nos 9,90,509
220/132kV Power Transformer Control & Relay Panels
20 10004037 Nos 10,89,102
with BCUs
220kV Bus Bar Scheme Panel (for 16 Bays) for double
21 10004027 Nos 14,50,000
bus system
22 10004023 220kV Bus Coupler Panel with BCUs. Nos 4,60,583
10004047 132 kV feeder Control & Relay Panel with BCUs with
23 Nos 4,51,417
10004048 Distance relay
10004048
132 kV Feeder Control & Relay Panel with BCUs with
24 10004049 Nos 7,50,000
Line Differential relay

132 /33 KV Power Transformer Control & Relay Panel

25 10004059 Nos 8,51,501
with BCUs as per BOM.
33 kV Twin feeder Control & Relay Panel with BCUs as
26 10004066 Nos 5,02,743
per BOM.
27 10004069 33KV Capacitor bank C&R Panels with BCUs Nos 5,70,651
28 Spare Transformer Differential relay (220/132KV ) Nos 2,00,000
29 Spare Line differential relay(220KV) Nos 2,50,000
30 Spare Distance relay(220KV) Nos 1,60,000
Industrial grade desktop PC with 24" (TFT) Monitor with
31 10010303 SET 1,89,884
software & furniture as per APTRANSCO BOM.
32 70002326 A4 Laser color printer with furniture as per BOM. Nos 59,963
GPS clock, antenna along with Associated
33 10010292 SET 1,44,911
equipment for time synchronization with existing relays.
3 KVA Inverters, Cabling & Installation as per aptransco
34 70002094 SET 94,942
Specification.
Data Concentrator for Energy Meters interface with
35 10012127 SET 15,000
IEC61850.
REMOTE Gateway consists of chassis, mother board,
power supply, processor with communication ports: a) IEC
36 10011651 SET 1,50,000
60870-5-101 and b) IEC 60870-5-104. (Suitable for
400kvSS, 220kv SS ,132 kV SS).
37 10011665 Industrial grade Ethernet Switches & Accessories. Nos 1,02,000

90
 File No.ENE51-PM0SYI(400)/12/2021-EE2

XLPE POWER CABLE AND ACCESSORRIES RATES FOR 400KV, 220KV and 132KV

Ex-Works Price
without GST
[Link]. SAP Code Description of Equipment/ Material Unit and F&I (in
Rs) SSR-2020-
21
Supply of 400 KV XLPE Under ground Single Core 2500
1 KM 3,89,39,067
[Link]. Copper Cable.

400kv [Link] Pre moulded joints without cross

2 Nos 20,48,148
bonding arrangements with copper casing and coffin box.

400kV [Link] Pre moulded joints with cross bonding

3 arrangements (Insulated joints)with copper casing and Nos 20,48,148
coffin box.
Design, Supply of 400KV, 2500 [Link] outdoor type
4 cable end terminations (sealing ends)with all materials Nos 24,85,000
complete in all respects.
Design, supply of 400KV, 2500Sqmm cable end
5 terminations complete in all respects (SF6 type cable Nos 16,40,781
terminations).
3 Phase Link boxes With SVL to cross bond the sheath
6 10003662 Nos. 1,31,917
suitable for 400kV XLP UG cable.
3 Phase Link boxes With out SVL to cross bond the sheath
7 10003663 Nos. 59,568
suitable for 400kV XLP UG cable.
1 phase Link boxes without SVL suitable for 400kV XLP
8 10003665 Nos. 23,700
UG cable.
Supply of 220 KV XLPE Under ground Single Core 1000
9 10003701 KM 1,38,67,104
[Link]. Copper Cable.

220kV 1000 [Link] Pre moulded joints without cross

10 10003705 Nos 5,85,000
bonding arrangements with copper casing and coffin box.

220kV [Link] Pre moulded joints with cross bonding

11 10003707 arrangements (Insulated joints)with copper casing and Nos 5,95,000
coffin box.
Design, Supply of 220KV, 1000 [Link] outdoor type
12 10003709 cable end terminations (sealing ends)with all materials Nos 9,65,569
complete in all respects.
Design, supply of 220 KV 1000Sqmm cable end
13 10010457 terminations complete in all respects (SF6 type cable Nos 6,97,800
terminations).
Supply of 132 KV XLPE Under ground Single Core 630
14 10003713 KM 82,27,473
[Link]. Copper Cable.

132kV 630 [Link] Pre moulded joints without cross

15 10003721 Nos 2,80,064
bonding arrangements with copper casing and coffin box.

132kV 630 [Link] Pre moulded joints with cross bonding

16 10003720 arrangements (Insulated joints)with copper casing and Nos 2,80,064
coffin box.
Design, Supply of 132 KV, 630 [Link] outdoor type cable
17 10003722 end terminations (sealing ends)with all materials complete Nos 4,13,867
in all respects.
Design, supply of 132 KV 630Sqmm cable end
18 10010456 terminations complete in all respects (SF6 type cable Nos 3,44,648
terminations).

91
 File No.ENE51-PM0SYI(400)/12/2021-EE2
Ex-Works Price
without GST
[Link]. SAP Code Description of Equipment/ Material Unit and F&I (in
Rs) SSR-2020-
21
19 10003662 3 Phase Link boxes With SVL to cross bond the sheath. Nos. 1,06,600
3 Phase Link boxes With out SVL to cross bond the
20 10003663 Nos. 59,568
sheath.
21 10003665 1 phase Link boxes without SVL. Nos. 19,987
Supply of 240 sqmm coaxial copper cable conductor PVC
22 10003206 insulated 6.6 KV grade with suitable lugs and glands for KM 48,50,000
joint bays.
Supply of 240 sqmm coaxial copper cable conductor PVC
23 10003209 insulated 6.6 KV grade with sheath bonding without cross KM 26,50,000
bonding joints to link box.
24 33KV 400Sqmm 1 core copper XLPE cable KM 28,94,300
25 33KV 400Sqmm 3core Al XLPE cable KM 21,05,900

92
 File No.ENE51-PM0SYI(400)/12/2021-EE2
GIS EQUIPMENT RATES FOR 400KV, 220KV, 132KV and 33KV
Ex-Works Price
without GST
[Link]. SAP Code Description of Equipment/ Material Unit and F&I
(in Rs)
SSR-2020-21
420kV, 4000 A, 63 kA, SF6 GIS transformer/feeder bay
1 10010470 SET 3,85,00,000
module.
420kV, 4000A, 63 kA, SF6 GIS Auxiliary Bus module for
2 10010468 SET 1,85,00,000
Spare Transformer/feeder.
420kV, 4000 A, 63 kA, SF6 GIS Line feeder bay module
3 10010469 SET 4,25,00,000
(with PIR).
420kV, 4000 A, 63 kA, SF6 GIS Line Reactor bay
4 SET 3,60,00,000
module.
5 10010471 420kV, 4000A, 63 kA, SF6 GIS Bus Reactor bay module. SET 3,60,00,000

420kV, 4000 A, 63 kA, SF6 GIS Bus Sectionalizer

6 SET 5,49,24,550
module.
420kV, 4000 A, 63 kA, SF6 GIS Tie bay module(with
7 10010472 SET 3,60,00,000
PIR).
420kV, 4000 A, 63 kA, SF6 GIS Tie bay module(without
8 SET 3,20,00,000
PIR).
420kV, 4000 A, 50 kA, SF6 GIS Bus Sectionalizer
9 SET 5,49,24,550
module.
420kV, SF6/Air Bushing for connecting GIS to AIS#
10 10010451 SET 5,00,000
4000A, 63kA.
420kV, 3000 A, 40 kA, Single phase, SF6 Gas Insulated
11 10010473 Bus Duct (GIB) outside GIS Hall along with associated mtrs 70,000
support structure.
12 SF6 Gas processing Unit. SET 65,00,000
70001118
13 70001119 EOT Crane for GIS Building. SET 26,00,000

Online Partial Discharge Monitoring System for 400kV

14 10010467 SET 2,50,00,000
GIS station.
15 10010477 400kv bus VT/CVT module. SET 65,00,000
10010402 245kV, 4000 A, 40KA, SF6 GIS transformer/ feeder bay
16 SET 2,00,00,000
module.
17 10010401 245kV, 4000 A, 50KA, SF6 GIS Line feeder bay module. SET 2,00,00,000
245kV, 4000 A, 50KA, SF6 GIS Bus bar module suitable
18 10010440 SET 1,50,00,000
for double bus arrangement.
245kV, 4000 A, 50KA, SF6 GIS Bus coupler bay module
19 10010403 SET 1,90,00,000
suitable for double bus arrangement.
245kV, 4000 A, 50 kA, SF6/Air Bushing for connecting
20 SET 12,00,000
GIS to AIS.
245kV, 1600A, 40kA, Single phase, SF6 Gas Insulated
21 10010442 Bus Duct (GIB) outside GIS Hall alongwith associated mtrs 72,000
support structure.
22 SF6 Gas processing unit for 220kV GIS station. SET 84,00,000

93
 File No.ENE51-PM0SYI(400)/12/2021-EE2
Ex-Works Price
without GST
[Link]. SAP Code Description of Equipment/ Material Unit and F&I
(in Rs)
SSR-2020-21
70001118
23 70001119 EOT Crane for GIS Building (220kV bus Duct). SET 21,00,000

24 10010467 Partial Discharge Monitor (220kV GIS) - OFFLINE. SET 60,00,000

25 10010482 245kv bus VT/CVT module. SET 77,00,000
145kV, 2500 A, 31.5 kA, SF6 GIS Line feeder bay
26 10010405 SET 1,00,00,000
module.
27 10010483 145kV, 2500 A, 31.5 kA, SF6 GIS Bus bar module. SET 60,00,000
145kV, 2500 A, 31.5 kA, SF6 GIS Bus bar coupler bay
28 10010407 SET 90,00,000
module as per Section-Project, Technical specification.
29 145kV, 2500A, 31.5KA SF6 TO AIR BUSHING. SET 3,85,000
145kV, 2500 A, 31.5 kA, 3 Phase, SF6 Gas Insulated Bus
30 duct (GIB) outside GIS Hall alongwith associated support mtrs 1,05,000
structure.
31 10010408 132kv VT/CVT module SET 50,00,000
32 SF6 Gas Processing Unit for 145kV GIS Station SET 84,00,000
70001118
33 70001119 EOT Crane for GIS Building (132kV GIS station). SET 17,00,000

Partial Discharge Monitoring system for 145kV GIS

34 SET 60,00,000
station.
36kV, 2500A, 25KA for 1 second, SF6 GAS- Insulated
35 10010484 SET 30,00,000
metal enclosed bus bar module.
10010443 36kV, 2500A, 25KA SF6 GIS transformer/ feeder bay
36 SET 35,00,000
10010453 module.
36kV, 3 - phase, 2500A, 25KA SF6 for 1 second, 33kV
37 10010447 SF6 GAS Insulated metal enclosed bus section bay SET 35,00,000
module.

94
 File No.ENE51-PM0SYI(400)/12/2021-EE2

VISUAL MONITORING SYSTEM FOR 400KV , 220KV AND 132KV SUBSTATIONS

Ex-Works Price
without GST
[Link]. Description of Equipment/ Material Unit
and F&I (in Rs)
SSR-2020-21

4 MP IP Bullet Cameras, IP66, 50 Mtrs IR, Day&Night,

1 No. 7,500
with 16x digital zoom.
4 MP IP Done Cameras, IP66 & IK10 rated rugged, 50mtrs
2 Nos 7,200
IR, Day&Night, with 16x digital zoom.
4 MP IP PTZ Cameras with 45x200(100mts) IR, IP66,
3 Nos 92,000
with 30x digital zoom.
4 2 MP IP uncooled Thermal PTZ Camera. Nos 4,65,000
5 64 Ch NVR with 4 sata. Nos 75,500
6 8 Tb Surveilance Hard Disc. Nos 19,500
17U Rack with fully loaded equipment and power
7 Nos 14,500
manager, rodent proof
8 1 KVA UPS with 20 minutes backup Nos 17,500
9 1 KVA UPS with surge protection Nos 6,500
VMS Metal surface boxes with Power manger and
10 termination box for OFC splicing and MCB connection Nos 6,500
with 1 KVA Surge protection.

10/100/1000 Gigabyte Mangeble layer 3 stackable

managed switch with 24 fiber slots and 4 combination of
11 Nos 82,000
LAN/fiber with physical stacking and fault torent topology
with versatilw 10G slots support with physical stacking.

28 Port L2 Gigabyte + stacking & routing smart managed

12 fiber switch with 24 port lan and 4 ports sfp slots with Nos 10,200
standaed mode or survilance mode.

1-Port Mini GBIC Module for 1000BaseLX (LC Duplex)

high performance 1310nm single mode SFP (mini -GBIC)
13 Nos 3,500
transceiver. Supporting full duplex, Gigabyte speeds on
single mode fiber for distances of up to 10km on 9Um.

10-Port Gigabit smart managed PoE switch, advanced L2

switching and security features, L2+Static Routing
14 Nos 14,100
optional "standard mode" or "surveillance mode"
management user interface.
15 8 PORT Giga byte POE. Nos 7,500
16 6U Fully loaded rack with Power manager. Nos 4,200
Fiber Duplix patch card LC-LC or LC-SC as per the LIU
17 Nos 1,000
functionality.
18 6 PORT loaded LIU with fiber pigtails and adoptors. Nos 3,500
19 6 Core single MODE armoured OFC cable. Mtrs 42
32 MM HDPE pipe for ducting purpose with anti
20 rodandant and suitale T junctions/C Sections, reducers & Mtrs 52
couplers.
21 CAT 6 Out Door Armoured cable. Bundles 12,500

95
 File No.ENE51-PM0SYI(400)/12/2021-EE2

Ex-Works Price
without GST
[Link]. Description of Equipment/ Material Unit
and F&I (in Rs)
SSR-2020-21

22 Power cable 2 core 2.5 sqmm seoured. Nos 41

23 55" LED TV with 2 HDMI slots. Nos 62,000
24 HDMI Cable. Nos 850
25 Wirless Mouses. Nos 600
26 CAT 6A Jacks. Nos 24
Other hardware accessories required for visual monitoring
27 Nos 50,000
system.
28 VMA Software Licence Nos 60,000
Complete Installation cost for commissioning of visual
29 LS. 1,50,000
monitoring system of 220kV SS.
Complete Installation cost for commissioning of visual
30 LS. 50,000
monitoring system of 132kV SS.

96