Document ID: 2690506 Page | of 5 2014 Holden VF Sedan | VE/WN Sedan, Ute, Sportwagon, Caprice, Lumina, HSV Service Manual 5617662 | Ensine/Propulsion | Cruise Control | Diagnostic Information and Procedures | Document ID: 2690506 Cruise Control Malfunction - DTC B3794, P0564, P0565, P0567, P0568, POS6C, P0580, P0581, P155A-P155C, or P162C Diagnostic Instructions + Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. + Review Strateqy Based Diagnosis for an overview of the diagnostic approach. + Dizqnostic Procedure Instructions provides an overview of each diagnostic category. DTC Descriptors DTC B379408 Cruise Control Function Request Circuit DTC B379461 Cruise Control Function Request Circuit DTcPos64 Cruise Control Multifunction Switch Circuit DTcPos6s Cruise Control Switch Circuit DTC P0567 Cruise Control Resume Switch Circuit DTc Poses Cruise Control Set Switch Circuit DTcPos6c Cruise Control Cancel Switch Circuit DTC Pos80 Cruise Control Multifunction Switch Circuit Low Voltage DTcPoss1 Cruise Control Multifunction Switch Circuit High Voltage DTCP155A Cruise Control Switch State Undetermined DTCP155B Cruise Control Set/Coast Switch 2 Circuit DTcP1ssc Cruise Control Resume/Acceleration Switch 2 Circuit pTcp162c © 2014 General Motors. All rights reserved, hitps://[Link]/gsi/[Link]?laborOpCode=&docSyskey=2690506&cellld=218718... 7/07/2014Page 2 of 5 Vehicle Speed Limiting/Werning Switch Circuit Diagnostic Fault Information Short to | Open/High | Short to Signal cireut Ground | Resiense | Votaye. | performance Tanitin 1 1 - = signal 1 | roses | Prosar.” | 8azeest, rose 1. Cruse Conta Hanction Circuit/System Description ‘The cruise control switch is an input to the body control module (BCM). The BCM monitors the cruise control on/off, set/coast, resume/accelerate and cancel switches via the cruise control switch signal circult in order to detect when the driver has requested to perform a cruise control function. The BCM detects a specific voltage signal on the cruise control switch signal Circuit when a switch is applied, The engine control module (ECM) receives the requested cruise control switch function from the BCM via a serial data message Conditions for Running the DTC « The cruise switch is ON. + The ignition is ON. Conditions for Setting the DTC B3794 08 ‘The BCM detects an invalid voltage signal on the cruise control switch signal circult for 1 second. 83794 61 Stuck switch for either Resume/Accel or Set/Coast button for 60 seconds. P0564, POS6S, P0567, POS6S, POS6C + The BCM detects an invalid voltage signal on the cruise control switch signal circuit for greater than 2 seconds and sends a serial data message to the ECM. The ECM sets these DTCs when the message is received. ‘+ The ECM runs this diagnostic continuously. P0580, POs81 ‘+ The ECM detects an invalid voltage signal on the cruise control switch signal circuit. ‘+ The above condition is present for greater than 2 seconds. + The ECM runs this diagnostic continuously. PASSA The ECM is unable to determine the state of the crulse control switch. Pi62c The ECM is unable to determine the state of the vehicle speed limiting switch Actions Taken When the DTC Sets hitps://[Link]/gsi/[Link]?laborOpCode=&docSyskey=2690506&cellld=218718... 7/07/2014Page 3 of 5 83794 + The malfunction indicator lamp (MIL) will not illuminate: + The cruise control system is disabled. P0564, POS6S, P0567, POS68, POSGC, POS8O, POSB1, P155A, P162C DTCs P0564, POSES, P0567, POSES, POSE, POS8O, P0581, PSSA and P162C are type C DTCs Conditions for Clearing the DTC B3794 ‘+ The condition responsible for setting the DTC no longer exists. «= Ahistory DTC will clear after 40 malfunction-free ignition cycles have occurred. P0564, P0565, P0567, P0568, POS6C, POS80, P0581, P155A, P162C DTCs POS64, POS6S, POS67, POS6S, POSEC, POS8O, POS81, PSSA and P162C are type C DTCs. Reference Information Schemat Reference Cruise Control Schematics Connector End View Reference Component Connector End Views Description and Operation Cruise Control Description and Operation Electrical Information Reference © Circuit Testing * Connector Repairs ‘« Testing for Intermittent Conditions and Poor Connections ‘© Wiring Repairs Scan Tool Reference Control Module References for scan tool Information Circuit/System Veri ication 1, Ignition ON 2. Verify that the stop lamps operate properly and that no B22 Brake Pedal Position Sensor related DTCs are set. = If brake pedal position sensor related DTCs are set Refer to Diaanostic Tr DTC) List - Vehi 4 If no brake pedal position sensor related DTCs are set 3. Verify the scan tool BCM Cruise Control Switch Status parameter changes between Off and ‘On, Resume and Set when switching between each position on the cruise control switch. > If the parameter does not change Refer to Circuit/System Testing. ¥ If the parameter changes 4, Verify that no conditions that may inhibit cruise control operation are present. Refer to the ECM scan tool data list Cruise Control Inhibit Reason parameter. Refer to the Cruise Control Description and Operation for a list of inhibit reasons. > If the cruise control system has a reason why it is inhi red hitps://[Link]/gsi/[Link]?laborOpCode=&docSyskey=2690506&cellld=218718... 7/07/2014Repair the condition that is causing the inhibit reason. Page 4 of 5 ¥ If the cruise control system does not have any reasons why it may be inhibited 5. Verify that no cruise control related DTCs are set. * If any cruise control related DTCs are set Refer to Circuit/System Testing. ¥ Ifno cruise control related DTCs are set 6. All OK, Circuit/System Testing Note: + An open ignition circuit or fuse before the control module will cause communication DTCs or power mode mismatch DTCs to set against or in the control module. This failure mode will be diagnosed in the no communications diagnostic procedure or power mode mismatch, + This test assumes the ignition circuit has a driver that will open under a high current condition before the fuse opens, + The driver can open under normal conditions such as battery run down prot: a retained accessory power mode. 1. Ignition OFF, disconnect the harness connector at the S7OL Steering Wheel Contr: -Left, ignition ON. 2. Verify a test lamp illuminates between the ignition circuit terminal 1 and ground. > If the test lamp does not 2.1. Ignition OFF, disconnect the harness connector at the K9 Body Control Modu 2.2. Test for greater than 100. between the ignition circuit and ground, = If 100 or less, repair the short to ground on the circuit. 4 If greater than 1009 2.3, Test for less than 29 in the ignition circuit end to end. juminate > If 29 or greater, repair the open/high resistance in the circuit. = If less than 29, test or replace the K9 Body Control Module. 4 Ifthe test lamp illuminates 3. Verify the scan tool ECM Cruise Control Switch Status parameter is Off, > If not off rection or ‘ols Switch 3.1, Ignition OFF, disconnect the harness connector at the K9 Body Control Module, Ignition ON. 3.2. Test for less than 1V between the signal circuit terminal 3 and ground. = If 1V or greater, repair the short to voltage on the circuit, = Ifless than 1V, replace the K9 Body Control Module. v If off 4, Install a 3A fused jumper wire between the signal circuit terminal 3 and the ignition circuit terminal 1 5. Verify the scan tool ECM Cruise Control parameter is Disabled. = If not Error 5.1, Ignition OFF, disconnect the harness connector at the K9 Body Control Module. 5.2. Test for infinite resistance between the signal circuit terminal 9 and ground. = If less than infinite resistance, repair the short to ground on the circuit. 4 If infinite resistance 5.3. Test for less than 29 in the signal circuit end to end. hitps://[Link]/gsi/[Link]?labor OpCode=&docSyskey=2690506&cellld=218718.. 7/07/2014Document ID: 2690506 Page 5 of 5 > If 2 or greater, repair the open/high resistance in the circuit. > If less than 29, replace the K9 Body Control Module. v If Error 6. Test or replace the S70L Steering Wheel Controls Switch-Left. Repair Instructions Perform the Diagnostic Repair Verification after completing the repair. Contra! Module References for BCM replacement, programming and setup. hitps://[Link]/gsi/[Link]?laborOpCode=&docSyskey=2690506&cellld=218718... 7/07/2014