D7 Smart Diagnosis System

User Manual

Shenzhen Xtooltech Intelligent Co., LTD

Please read this user manual carefully before using the D7
Smart Diagnosis System. When reading the manual, please
pay attention to the words “Note” or “Caution”, and read them
carefully for appropriate operation.

TRADEMARKS

is a registered trademark of Shenzhen Xtooltech

Intelligent CO., LTD.
In countries where the trademarks, service marks, domain
names, logos and the name of the company are not registered,
XTOOL claims that it still reserves the ownership of the
unregistered trademarks, service marks, domain names, logos
and the company name. All other marks for the other products
and the company’s name mentioned in the manual still belong
to the original registered company.
You may not use the trademarks, service marks, domain
names, logo and company name of XTOOL or other companies
mentioned without written permission from the trademark holder.
XTOOL reserves the right to the final interpretation of this
manual content.

I
COPYRIGHT

Without the written consent of Shenzhen Xtooltech Intelligent

Co., Ltd., any company or individual shall not copy or backup
this operation manual in any form (electronic, mechanical,
photocopying, recording or other forms).

DECLARATION

This manual is designed for the usage of the D7 Smart

Diagnosis System and provides operating instructions and
product descriptions for users of the D7 Smart Diagnostic
system.
No part of this manual can be reproduced, stored in a retrieval
system or transmitted, in any form or by any means (electronic,
mechanical, photocopying, recording, or otherwise), without the
prior written permission of XTOOL.
Use the device only as described in this manual. XTOOL is not
responsible for any consequences of violating the laws and
regulations caused by using the product or its data information
XTOOL shall not be liable for any incidental or consequential
damages or for any economic consequential damages arising
II
from the accidents of individual users and the third parties,
misuse or abuse of the device, unauthorized change or repair
of the device, or the failure made by the user not to use the
product according to the manual.
All information, specifications and illustrations in this manual
are based on the latest configurations and functions available at
the time of printing. XTOOL reserves the right to make changes
at any time without notice.

OPERATION INSTRUCTIONS

For safe operation, please follow the instructions below:

 Keep the device away from heat or fumes when you use it.
 If the vehicle battery contains acid, please keep your hands
and skin or fire sources away from the battery during
testing.
 The exhaust gas of the vehicle contains harmful chemicals,
please ensure adequate ventilation.
 Do not touch the cooling system components or exhaust
manifolds when the engine is running due to the high
temperatures reached.

III
 Make sure the car is securely parked, Neutral is selected
or the selector is at P or N position to prevent the vehicle
from moving when the engine starts.
 Make sure the (DLC) diagnostic link connector is
functioning properly before starting the test to avoid
damage to the Diagnostic Computer.
 Do not switch off the power or unplug the connectors
during testing, otherwise, you may damage the ECU and/or
the Diagnostic Computer.

CAUTIONS!

 Avoid shaking or dismantling the unit as it may damage the

internal components.
 Do not use hard or sharp objects to touch the LCD screen;
 Do not use excessive force;
 Do not expose the screen to strong sunlight for a long
period.
 Please keep it away from water, moisture, high
temperature or very low temperature.
 If necessary, calibrate the screen before testing to ensure
the accuracy of LCD performance.
 Keep the main unit away from strong magnetic fields.

IV
AFTERSALES-SERVICES

E-Mail: aftersales-services@[Link]
Tel: +86 755 21670995 or +86 755 86267858 (China)

Official Website: [Link]

V
CONTENT

TRADEMARKS..............................................................................I
COPYRIGHT................................................................................. II
DECLARATION............................................................................ II
OPERATION INSTRUCTIONS................................................. III
CAUTIONS!................................................................................. IV
AFTERSALES-SERVICES........................................................ V
CONTENT.......................................................................................I
1 GENERAL INTRODUCTION.................................................. 1
Tablet.............................................................................................. 2
Front View of Tablet.............................................................................. 2
Back View of Tablet.............................................................................. 3
Host Ports............................................................................................... 4

Technical Specifications..............................................................5

Package Kit....................................................................................6
Main Unit.................................................................................................6
Other Accessories................................................................................. 6

2 GETTING STARTED................................................................ 7
Activation........................................................................................7

i
 Main Interface............................................................................. 10
Operation system................................................................................ 10
Diagnosis system entrance................................................................12
Function Buttons................................................................................. 13
Navigation Buttons.............................................................................. 14
Notification Bar.................................................................................... 15

Factory Reset..............................................................................17

3 UPDATE................................................................................... 19
4 DIAGNOSIS............................................................................. 21
Vehicle Connection.................................................................... 21

Diagnosis..................................................................................... 22
Vehicle Selection.................................................................................23
Basic functions.....................................................................................25

5 SPECIAL FUNCTIONS..........................................................33
Oil Reset...................................................................................... 34

EPB............................................................................................... 35

SAS............................................................................................... 36

DPF............................................................................................... 37

BMS MATCH...............................................................................38

Throttle......................................................................................... 39

TPMS Reset................................................................................ 39

ABS Bleeding.............................................................................. 40

ii
 Injector Coding............................................................................41

Gearbox Match........................................................................... 42

Suspension.................................................................................. 42

Windows Initialization................................................................ 43

Seat Match...................................................................................43

Headlight Adjustment.................................................................43

IMMO Service............................................................................. 44

Gear Learning............................................................................. 45

6 SETTINGS................................................................................47
Language..................................................................................... 47

Units..............................................................................................49

My Workshop Info...................................................................... 50

VCI Information........................................................................... 51

About............................................................................................ 52

7 REPORT................................................................................... 53
Report...........................................................................................54

Replay.......................................................................................... 57

File Manager............................................................................... 57

8 REMOTE ASSISTANCE........................................................58
9 FAQ........................................................................................... 60
Q1: Failed to generate diagnosis report................................. 60

iii
Q2: How to print diagnosis report............................................ 62

Q3: Failed to extract files.......................................................... 62

Q4: Mailbox supported.............................................................. 63

Q5: How to make an appointment for remote support.........63

Q6: How to generate and upload diagnostic log files...........63

Q7: How to switch language.....................................................64

Q8: Failed to diagnose vehicle.................................................64

Q9: Failed to activate or register..............................................65

Q10: Failed to turn on when charging.....................................65

Q11: Failed to open the diagnosis app...................................65

iv
1 GENERAL INTRODUCTION
The XTOOL D7 smart diagnostic system is an advanced flatbed
scanning tool based on the Android operating system. It
supports multi-language switching and is suitable for different
countries and regions. The advantage of this obd2 scanner is
not only its comprehensive functions, including complete
system diagnosis, all obd2 functions, various reset functions
(IMMO / EEPROM adapter / EPB (Electronic Parking Brake)
reset / oil light reset / SAS (Steering Angle Sensors) reset / TPS
(Throttle Position Sensor) matching / Injector coding / ABS
(Anti-block system) bleed / gearbox matching / gear learning /
electronic pump actuation / disable transport mode / SRS
(Supplemental Restrgint System) reset / exhaust post-
processing / BMS matching / air suspension / cylinder / TPMS
reset / tire refit / headlight adjustment / windows
Initialization/seat matching/DIY mode) can also achieve faster
and more accurate diagnosis.

1
TABLET

The main unit of the D7 is the tablet, which has a built-in VCI
module, which can be directly connected to the tablet and the
car with the main test line, without the need to connect to an
external VCI box via Bluetooth.

FRONT VIEW OF TABLET

Fig 1-1 Tablet Front View

The front of the main unit is a touchable display screen, you
can use your fingers to operate on the screen to complete the
car diagnosis.

2
BACK VIEW OF TABLET

Fig 1-2 Tablet Back View

The product model and S/N are laser-engraved on the back of
the display tablet, and the small hole at the bottom is the
Loudspeaker.
1 Nameplate: Display basic information such as S/N and
model etc.
2 Loudspeaker: external sound can be played, supporting
the playback of music, etc.

3
HOST PORTS

Fig 1-3 Tablet Host Ports

① Micro USB: Battery charge or data synchronization with PC
or DC.
②DB15 Port: This port is used to connect to the main test cable.
③Power Button: Long press to power on or off. In the power-on
state, short press the button to make the device enter the sleep
mode.

4
TECHNICAL SPECIFICATIONS
Table 1-1 Specification

Item Description

Operating System Android

Processor Quad-core 1.6GHz Processor

Memory 32GB

7.0-inch touch screen with 1024 × 600

Display
resolution

 USB
Connectivity
 Wi-Fi

Sensors Gravity sensor, light sensor

Microphone, dual speakers, 4-band

Auto Input/Output
3.5mm stereo/standard headset jack

Power and Battery 4000mAh, 3.7V lithium-polymer battery

Power Voltage 5V

Power Consumption 8W

Operating -20 to 60℃(-4 to 140℉)

Temperature

Storage Temperature -40 to 70℃(-40 to 158℉)

Humidity <90%

Dimension (L*W*H) 218*150*29mm

5
PACKAGE KIT

MAIN UNIT

 Tablet 1 pcs

OTHER ACCESSORIES

 OBDⅡ-16 Connector (1 pcs)

* Used to access vehicle ECU data
 Main Test Cable (1 pcs)
*The main cable is used to connect the Tablet to the connector.
 USB Cable
*Connect display table to the PC or DC power adapter
 Power Adapters
a) Charger DC5V AC100-300V 2A USB socket output No AC
movable feet 1 pcs
b) AC Charger Adapter 1 pcs (EU Standard)
c) AC Charger Adapter 1 pcs (US Standard)
*Used to connect a USB cable to connect the tablet to an external
DC power port for charging.
 User Manual
*Tool operation instructions

6
2 GETTING STARTED

ACTIVATION

After first-time users press and hold the power button to turn on
the system, the system will automatically enter the guide
process and request to select the language for the operating
system.

Fig 2-1
After setting the system language, you will enter the activation
page, as shown in the figure below. You can also click the

7
"Trial" button in the upper right corner to try it out before
activation.

Fig 2-2
Click Start Activate to enter the activation page, as shown
below:

8
 Fig 2-3
A pop-up window showing Activation Success indicates that
you have completed the first boot setup, click OK to enter the
diagnostic system and start using the device.

Fig 2-4

9
MAIN INTERFACE

OPERATION SYSTEM

As shown in the figure below, this interface is the main page of

the operating system of the device. You can also return to this
interface at any time by clicking 【⚪ 】on the bottom navigation

bar.

Fig 2-5
The icons on the right, from top to bottom, are browser, photo
album, application square, file manager, system settings, as
shown below:

10
 Table 2-1

Items Descriptions

Browser

Album

Application Square

File Explorer

Settings for Android System

a) Browser: Click on the browser icon to enter the browser to

view the official website of XTOOL or search for other
information.
b) Gallery: Click the Gallery icon to enter the album to
quickly view the pictures or screenshots stored in the
device. You can select the picture you need, click the
share button on the upper right, and send the picture to
your mobile phone or PC via Bluetooth or USB connection
c) Application Square: This function is suitable for power
balance after replacing and repairing the cylinder. You can
remove or add apps here.

11
 Fig 2-6
d) ES File Explorer:
You can manage APP, music, files, pictures, etc. in the device
in this function, and you can also use Local/Home/Cleaner to
clean up files.

DIAGNOSIS SYSTEM ENTRANCE

Once activated, you will automatically enter the diagnostic

system with the following main screen. Tap on the diagnosis
application button on the menu, the main interface will be
shown as below:

12
 Fig 2-7
The main interface is mainly composed of Function Buttons
and Navigation Buttons. The touch screen navigation is
menu-driven, and you can quickly access functions by clicking
on the option title and answering the dialogue window. A
detailed description of the menu structure can be found in the
next section Function Buttons.

FUNCTION BUTTONS

The following table briefly describes each function button

Table 2-2

Item Description

Quickly access to the vehicle system to identify

the vehicle VIN code
13
 Enter to select a vehicle

Includes special functions for car diagnosis

You can view the vehicle diagnostic report

In case of failure, you can control the

diagnostic equipment remotely

Users can upgrade the available software with

one click
Users can set the language, unit, Bluetooth,
repair shop information, also can view
information about this software

Users can view more extended functions

NAVIGATION BUTTONS

Instructions for operating the navigation bar buttons at the

bottom of the screen, as described in the table below:
Table 2-3

Items Descriptions

Back to the previous interface

Back to the main interface of the Android

system
14
 Shows recently used applications

Press for screenshot

Decrease volume

Click this button to return to the diagnostic

vehicle interface

Increase volume

Click here to return to the diagnostic vehicle

models interface

NOTIFICATION BAR

Slide down to open the notification bar. Users can adjust the
brightness of the screen when they need it, and you can also
connect Wi-Fi and so on.

15
Fig 2-8

16
FACTORY RESET

When you choose to restore factory settings in the OS system,

the device will automatically restart and enter the factory mode
to pull the software. You can select the language in the
following interface.

Fig 2-9
After selecting the system language, click Next to enter the Wi-
Fi connection page, as shown below:

17
 Fig 2-10
Select a network to connect to on the Wi-Fi connection page.
After successful network connection, the automatic system will
jump to Factory mode to download the software:

Fig 2-11
Once the software has been downloaded, the tablet will
18
automatically reboot and request the system language selection
again.

Fig 2-11
Since restoring the factory settings will erase the user
information on your device, you need to enter the email again to
activate your device

3 UPDATE
After activating the device, please update the software in
"Update" first. The device will pull all currently supported
software packages, and you can download them as needed.
ALL software updates directly via the Internet. To access the

19
update application, open the diagnosis application and click
UPDATE, shown as below:

Fig 3-1
*Note:
After contacting your dealer to change the language
configuration, you need to download all the software packages
on the device again

20
4 DIAGNOSIS
The diagnostic application can read ECU information, read and
clear DTC and check living data and freeze frames. The
diagnosis application can access the electronic control unit
(ECU) of various vehicle control systems, including the engine,
transmission, anti-lock braking system (ABS), airbag system
(SRS), and perform kinds of actuation tests.

VEHICLE CONNECTION

The diagnosis operation needs to connect the D7 smart

diagnosis system to a vehicle first so that the tablet can
establish correct vehicle communication. Please perform the
following steps:
1 Turn on the tablet;
2 Connect cables and tablet in the following order: ①→②→
③→④;
3 Switch on the ignition and tap on the diagnosis application
to test vehicles.
Since the display panel and the VCI box are integrated, to
communicate with the vehicle, the OBD Ⅱ -16 connector must
be connected to the main test cable, and the vehicle data

21
connector should be inserted into the DLC usually located
under the vehicle dashboard.
The connection method is shown in the figure below:

Fig 4-1
1 Tablet
2 Main Test Cable
3 OBDII-16 Connector
4 Vehicle
*Caution: Please make sure all the cables are connected
tightly; The vehicle’s DLC is not always located under the dash;
for the location of the DLC, please refer to the vehicle’s user
manual.

DIAGNOSIS

After the tablet device is properly connected to the vehicle, the

system can begin vehicle diagnosis. You can select the vehicle
22
model that needs to be diagnosed according to the area, as
shown below:

Fig 4-2
*Note: OBDⅡ supports reading the common fault codes in the
engine; DEMO, a demonstration program. Click this button to
experience and learn the operation process of the diagnostic
function.

VEHICLE SELECTION

D7 Smart Diagnosis System support 2 ways to access the

vehicle diagnosis system.
You can select "Automatic Detection" or "Manual Selection"
to enter the diagnosis system. Automatic detection will
automatically identify the vehicle's VIN code, and then read the
information of your target diagnostic object. If you
23
choose "manual selection", then you can start the diagnosis by
selecting the vehicle brand, year, and model of the vehicle.
Enter "manual selection", you can also diagnose the car
according to the system according to your needs after selecting
the model.

Fig 4-3

24
BASIC FUNCTIONS

The diagnosis system supports 5 basic diagnosis functions, as

follows:
 Read ECU
 Read /Clear DTCs
 Read Live Data
 Actuation Test
 Freeze Frame

Fig 4-4

Read ECU Information: This function is to read ECU version

information, which is the equivalent of "System Identification"
or "System information in some electronic control systems, all
mean to read ECU related software and hardware versions,
models and production date of diesel engine, part number, etc.

25
It is convenient for us to make a record in the maintenance
process, and it also makes data feedback and management
easier.

Fig 4-5

Read Trouble Code: Read trouble codes stored in ECU.

26
 Fig 4-6
*Tip: In the process of diagnosis, if the device shows “System
is OK” or “No Trouble Code”, it means there is no related
trouble code stored in ECU or some troubles are not under the
control of ECU, most of these troubles are mechanical system
troubles or executive circuit troubles, it is also possible that
signal of the sensor may bias within limits, which can be judged
in Live Data.

Clear Trouble Code: It allows to clear current and historical

trouble codes memory in ECU, under the premise that all the
troubles are eliminated.

27
 Fig 4-7
The trouble codes can’t be erased without eliminating all the
troubles, which will cause the diagnostic tool to always read the
trouble code because the code will always be saved in ECU.
Suggestion: users should better not clear trouble codes, we
need to record the trouble details after reading the code, which
is provided as a reference for maintenance. After dealing with
troubles, there will be no trouble code when we re-read.

Read Live Data: that is to read the parameters of running

engine, such as oil pressure, temperature, engine speed, fuel
oil temperature, coolant temperature, intake air temperature,
etc. Based on these parameters, we can judge directly where
the problem lies, which helps to narrow the scope of
maintenance. For some vehicles, during their actual operation,

28
the problems such as performance characteristics offset,
sensitivity reduction, can be judged in live data.

Fig 4-8

Fig 4-9

29
In the process of diagnosis, if the device shows “System is
OK” or “No Trouble Code”, it means there is no related
trouble code stored in ECU or some troubles are not under the
control of ECU, most of these troubles are mechanical system
troubles or executive circuit troubles, it is also possible that
signal of the sensor may bias within limits, which can be judged
in Live Data.

Actuation Test: Actuation test, also known as bidirectional

control, is a generic term used to describe sending and
receiving information between one device and another. This
function is used mainly to judge whether these actuating
components of the engine are working properly.
The vehicle engineers responsible for designing computer
control systems programmed them so a scan tool could request
information or command a module to perform specific tests and
functions. Some manufacturers refer to bidirectional controls as
functional tests, actuator tests, inspection tests, system tests or
the like. Reinitialization and reprogramming also can be
included in the list of bidirectional controls.
This function allows the device to send information to and
receive information from, vehicle control modules. For example,
in the case of OBD II generic information Mode 1 (which relates
to data parameters), the scan tool user initiates a request for
information from the powertrain control module (PCM), and the
30
PCM responds by sending the information back to the scan tool
for display. Most enhanced scan tools also can actuate relays,
injectors and coils, perform system tests, etc. Users could
check the individual part to see what is working properly by
actuation test.

Fig 4-10 click on Continue to complete the test

Freeze Frame: When the signal of the sensor is abnormal, the

ECU will save the data at that moment of failure to form a
freeze-frame. It is usually used to analyze the reasons that may
lead to car failures.
The living data items supported by vehicles of different brands
are not the same, so the freeze frames displayed when
diagnosing vehicles of different brands may also be different.

31
Some vehicles may not have the option of a freeze-frame which
means that the model does not support this function.

32
5 SPECIAL FUNCTIONS
The D7 Smart Diagnosis System supports 23 commonly used
special reset functions, allowing you to quickly access your
vehicle system for various scheduled services, maintenance
and reset performance, eliminating the need to reset after
resolving common problems. This user manual lists some of the
commonly used special reset services for your reference. The
special functions interface is shown as below:

Fig 5-1
*Note:
Due to the limitation of screenshots, the special functions
shown in this picture are not complete. All special functions
33
supported by D7 are subject to the actual special functions
displayed on the device.

OIL RESET

Reset the Engine Oil Life System, which calculates the

optimum oil life change interval based on the vehicle's driving
conditions and climate. The oil life reminder must be reset each
time the oil is changed so that the system can calculate when
the next oil change is required.

This function allows you to perform a reset for the engine oil life
system, which calculates an optimal oil life change interval
depending on the vehicle driving conditions and climate.
This function can be performed in the following cases:
 If the service lamp is on, you must provide service for the
car. After service, you need to reset the driving mileage or
driving time so that the service lamp turns off and the
system enables the new service cycle.
 After changing engine oil or electric appliances that monitor
oil life, you need to reset the service lamp.

34
EPB

Electronic Parking Brake (EPB) System reset is a popular

special function. You can use this function to reset the
electronic parking brake system and brake pads, which also
supports the brake pad replacement (retraction, release of the
brake pump), G-sensor and body angle calibration. This
function has multiple uses and can safely and effectively
maintain the electronic brake system. These applications
include deactivating and activating brake control systems,
assisting in controlling brake fluid, opening and closing brake
pads, and setting brakes after replacing brake discs or brake
pads, etc.
1. If the brake pad wears the brake pad sense line, the brake
pad sense line sends a signal sense line to the onboard
computer to replace the brake pad.
After replacing the brake pad, you must reset the brake pad.
Otherwise, the car alarms.
2. Reset must be performed in the following cases:
 The brake pad and brake pad wear sensor are replaced.
 The brake pad indicator lamp is on.
 The brake pad sensor circuit is short, which is recovered.
 The servo motor is replaced.

35
SAS

Steering Angle Sensors (SAS) System Calibration permanently

stores the current steering wheel position as the straight-ahead
position in the SAS EEPROM. Therefore, the front wheels and
the steering wheel must be set exactly to the straight-ahead
position before calibration. In addition, the VIN is also read from
the instrument cluster and stored permanently in the SAS
EEPROM. On successful completion of calibration, the SAS
fault memory is automatically cleared.
To reset the steering angle, first find the relative zero point
position for the car to drive in a straight line. Taking this position
as a reference, the ECU can calculate the accurate angle for
left and right steering.
After replacing the steering angle position sensor, replacing
steering mechanical parts (such as steering gearbox, steering
column, end tie rod, steering knuckle), performing four-wheel
alignment, or recovering the car body, you must reset the
steering angle.

36
DPF

The Diesel Particle Filter (DPF) function manages DPF

regeneration, DPF component replacement teach-in and DPF
teach-in after replacing the engine control unit.
The ECM monitors driving style and selects a suitable time to
employ regeneration. Cars driven a lot at idling speed and low
load will attempt to regenerate earlier than cars driven more
with higher load and speed. For regeneration to take place, a
prolonged high exhaust temperature must be obtained.
In the event of the car being driven in such a way that
regeneration is not possible, i.e., frequent short journeys, a
diagnostic trouble code will eventually be registered in addition
to the DPF light and “Check Engine” indicators displaying. A
service regeneration can be requested in the workshop using
the diagnostic tool.

DPF regeneration is used to clear PM (Particulate Matter) from

the DPF filter through continuous combustion oxidation mode
(such as high-temperature heating combustion, fuel additive or
catalyst reduce PM ignition combustion) to stabilize the filter
performance.
DPF regeneration may be performed in the following cases:
 The exhaust back pressure sensor is replaced.

37
 The PM trap is removed or replaced.
 The fuel additive nozzle is removed or replaced.
 The catalytic oxidizer is removed or replaced.
 The DPF regeneration MIL is on and maintenance is
performed.
 The DPF regeneration control module is replaced.

BMS MATCH

The Battery Management System (BMS) allows the scan tool to

evaluate the battery charge state, monitor the close-circuit
current, register the battery replacement, and activate the rest
state of the vehicle.
This function enables you to perform a resetting operation on
the monitoring unit of the vehicle battery, in which the original
low battery fault information will be cleared and battery
matching will be done.
Battery matching must be performed in the following cases:
 The main battery is replaced. Battery matching must be
performed to clear original low battery information and
prevent the related control module from detecting false
information. If the related control module detects false
information, it will invalidate some electric auxiliary
functions, such as automatic start & stop function, sunroof
without one-key trigger function, power window
38
 without automatic function.
 Battery monitoring sensor. Battery matching is performed
to re-match the control module and motoring sensor to
detect battery power usage more accurately, which can
avoid an error message displayed on the instrument panel.

THROTTLE

Throttle Position Sensor (TPS) Match, this function enables you

to make initial settings to throttle actuators and returns the
“learned” values stored on ECU to the default state. Doing so
can accurately control the actions of regulating throttle (or idle
engine) to adjust the amount of air intake.

TPMS RESET

Tire Pressure Monitor System (TPMS) Reset allows you to

quickly look up the tire sensor IDs from the vehicle ECU, as
well as to perform TPMS replacement and reset procedures
after tire sensors are replaced.

This function allows you to quickly lookup the tire sensor IDs
from the vehicle’s ECU, as well as to perform TPMS
replacement and sensor tests.

39
 After the tire pressure MIL turns on and maintenance is
performed, the tire pressure resetting function must be
performed to reset tire pressure and turn off the tire
pressure MIL.
 Tire pressure resetting must be performed after
maintenance is performed in the following cases: tire
pressure is too low, tire leaks, tire pressure monitoring
device is replaced or installed, the tire is replaced, the tire
pressure sensor is damaged, and tire is replaced for the
car with tire pressure monitoring function.

ABS BLEEDING

Anti-lock Braking System (ABS) Bleeding allows you to perform

various bi-directional tests to check the operating conditions of
ABS.
1. When the ABS contains air, the ABS bleeding function must
be performed to bleed the brake system to restore ABS brake
sensitivity.
2. If the ABS computer, ABS pump, brake master cylinder,
brake cylinder, brake line, or brake fluid is replaced, the ABS
bleeding function must be performed to bleed the ABS.
3. After the oil in the brake oil tank is seriously insufficient or the
brake fluid is replaced, ABS Bleeding is also required
*Note
40
 When performing ABS Bleeding, it is necessary to unscrew
the exhaust screw of the ABS pump.
 After completing the tire pressure sensor learning, it takes
a while for the fault light to go out.
 Tire pressure imbalance will also cause the tire pressure
light to light up.

INJECTOR CODING

This function can write the identification code of the fuel injector
into the ECU so that the ECU can recognize and work normally.
Write injector actual code or rewrite code in the ECU to the
injector code of the corresponding cylinder to more accurately
control or correct cylinder injection quantity.
After the ECU or injector is replaced, the injector code of each
cylinder must be confirmed or re-coded so that the cylinder can
better identify injectors to accurately control fuel injection.
*Note
1. After cleaning, generally there is no need to do the coding
matching function.
2. The identification of the fuel injector includes its working
accuracy value and type value. When replacing it, you need to
find the corresponding model for replacement.
3. At present, mainstream cars support injector coding function

41
GEARBOX MATCH

After changing the gearbox or changing the gearbox ECU, you

need to use the gearbox matching function to re-match the
engine and the gearbox.
*Cautions!
Before resetting the gearbox, please check the gearbox control
unit to ensure that there is no fault code. If there is a fault code,
the gearbox memory function cannot be reset. Please road test
after reset.

SUSPENSION

This function can adjust the height of the vehicle body. When
replacing the body height sensor in the air suspension system,
or control module or when the vehicle level is incorrect, you
need to perform this function to adjust the body height sensor
for level calibration.
The air suspension system reset function enables the computer
ECU to match the current air suspension system information,
thereby ensuring the normal damping effect of the vehicle when
driving.
Application scenarios:
 The shock absorber is not the same height due to air
leakage, maintenance, replacement, etc.;
42
 After replacing the air pump assembly;
 After replacing the control computer ECU.

WINDOWS INITIALIZATION

This function is to match the windows to restore the initial

memory of the ECU and restore the automatic raising and
lowering functions of the power window. Usually, when the
vehicle window fails or after replacing the window glass, we
need to use this function to initialize the car window.

SEAT MATCH

This function is suitable for the matching of replacement and

maintenance seats with memory functions. After the seat fails
or is replaced or repaired, it is generally necessary to use this
function to match the seat.
*Cautions: Needed for cars with seats with memory function,
general gasoline cars don’t need.

HEADLIGHT ADJUSTMENT

Refers to the adaptive front lighting system (when using bi-

xenon headlights at night), it can be rotated to both sides,

43
pressing the button means that they stay indirect light, and will
not turn when you turn the steering wheel.

IMMO SERVICE

An immobilizer is an anti-theft mechanism that prevents a

vehicle’s engine from starting unless the correct ignition key or
other device is present. Most new vehicles have an immobilizer
as standard equipment. An important advantage of this system
is that it doesn’t require the car owner to activate it since it
operates automatically. An immobilizer is considered as
providing much more effective anti-theft protection than an
audible alarm alone.
As an anti-theft device, an immobilizer disables one of the
systems needed to start a car’s engine, usually the ignition or
the fuel supply. This is accomplished by radio frequency
identification between a transponder in the ignition key and a
device called a radio frequency reader in the steering column.
When the key is placed in the ignition, the transponder sends a
signal with a unique identification code to the reader, which
relays it to a receiver in the vehicle’s computer control module.
If the code is correct, the computer allows the fuel supply and
ignition systems to operate and start the car. If the code is
incorrect or absent, the computer disables the system, and the
car will be unable to start until the correct key is placed in the
44
ignition.
To prevent the car from being used by unauthorized keys, the
anti-theft key matching function must be performed so that the
immobilizer control system on the car identifies and authorizes
remote control keys to normally use the car.
When the ignition switch key, ignition switch, combined
instrument panel, ECU, BCM, or remote-control battery is
replaced, anti-theft key matching must be performed.
The IMMO service can disable a lost vehicle key and program
the replacement key fob. One or more replacement key fobs
can be programmed.
*Note
Some models need to be used with an EEPROM adapter for
IMMO service. The EEPROM adapter is not included in this
product. Please purchase it separately if you need to use it.

GEAR LEARNING

The crankshaft position sensor learns crankshaft tooth

machining tolerance and saves to the computer to more
accurately diagnose engine misfires. If tooth learning is not
performed for a car equipped with a Delphi engine, the MIL
turns on after the engine is started. The diagnostic device
detects the DTC P1336 'tooth not learned'. In this case, you
must use the diagnostic device to perform tooth
45
learning for the car. After tooth learning is successful, the MIL
turns off. This function can complete the self-learning of the
gearbox and improve the quality of shifting.
After the engine ECU, crankshaft position sensor, or crankshaft
flywheel is replaced, or the DTC 'tooth not learned' is present,
tooth learning must be performed.

46
6 SETTINGS
Click the Settings button to adjust the default settings and view
information about the D7 Smart Diagnosis System. There are
seven options available in the system settings:
 Language
 Units
 My Workshop Info
 VCI Info
 About

LANGUAGE
The languages supported by this device are listed in Settings.
In areas outside the English area, the default language is
English and the local official language. Users can switch
between English and local official languages on the device by
themselves. If you need to switch other languages, please
contact the dealer to unbind the current language configuration
and rebind it to the language configuration you need to switch.
After the configuration is successfully changed, you can switch
the target language.
.

47
 Fig 6-1
 This will only change the language of the APP. If you want
to change the system language, please go to Android Settings.
 How to change the language of your software?
 Step1: Contact your dealer and leave a message about
the language you need and the S/N of your device, The
technician will modify the language configuration for you in
the background.
 Step2: Settings->Language->Choose language
 Step3: OS Settings->Language & input->Choose
Language

48
 Note: The types and quantities of languages supported are
subject to the actual language types displayed on the
device

 Step4: Back to Updates to pull all packages again

UNITS

You can switch the unit used by the system. D7 Smart

Diagnosis System provides you with Metric, Imperial, and U.S.
units. You can directly click on the unit you need, after the
switch is successful, a blue checkmark will be displayed behind
the unit’s name.

Fig 6-2

49
MY WORKSHOP INFO

Click on My Workshop Information, you can input your

workshop information here. As shown in the figure below, you
just need to fill in the valid information in the corresponding
column and click "SUBMIT". And then it will show your
workshop information in the report when you generate a
diagnostic report, including your company name, address,
website, telephone, and mailbox.

Fig 6-3

50
VCI INFORMATION

Fig 6-4
You can view the VCI information here, including the VCI
firmware name, the latest firmware version, the currently used
firmware version, and the VCI firmware type.

 The diagnosis tablet supports automatic firmware update,

please make sure that the device is connected to the network
when you enter the diagnostic software and the firmware will be
automatically updated to the latest version.

51
ABOUT

Tap on ABOUT, you can check the serial number and APP
version on here.

Fig 6-5

52
7 REPORT
Diagnostic Report is used for viewing and printing the saved
files, such as Live Data, Trouble codes or pictures generated in
the process of diagnosis, users also can view a record of which
cars have been previously tested. It includes 3 parts:
 Report
 Replay
 File Management

Fig 7-1

REPORT
This feature provides a history of diagnostic reports, where
53
you can view and delete the vehicle's diagnostic reports
according to your needs.

Fig 7-2
When you open the report, located in the header of the table is
the studio information you filled in advance in the system setup,
then the information of the vehicle, as shown as below:

54
 Fig 6-3
 Print PDF Report
As you can see, you also could click " Print PDF Report " at
the bottom right corner to output the pdf report. If you need to
close the report, you could tap on the button “Exit”.
Please follow the below steps to print your report▼
Step 1: Install an APP that can drive your target printer. Add
the printer and input the IP address of the printer in the APP, or
you can contact your dealer for help.
 D7 Smart Diagnosis System doesn’t provide the printer
driver software, please install a third part App on the tablet if
you need the print your diagnosis report.
Step 2: Back to the Android main menu, go to Settings ->
Printing-> Turn printer on.
Step 3: Report-> Choose report-> Print PDF Report-> Print

55
 Fig 6-4
Step 4: Click the top-left corner of the screen and choose the
printer you added before. Then click the button on the right to
print.

Fig 6-5

REPLAY
This function allows you to replay the living data recorded
during the diagnosis process.
Before replaying the living data, please make sure you have
recorded the live data during the diagnosis

56
FILE MANAGER
This function allows you to check and delete files on the device.
Please use this function under the guidance of professionals.
Ordinary users are not recommended to use it by themselves,
as it may cause software missing or malfunctioning.

57
8 REMOTE ASSISTANCE
Tap on "Remote" to start the TeamViewer quick support
program, which is a simple, fast, and secure remote-control
screen. You can use this application to enable them to control
your tablet on a PC through the TeamViewer software, thereby
obtaining temporary remote support from XTOOL's technical
support centre.
Computers and mobile devices running TeamViewer are
identified by a globally unique ID. When the remote application
is started for the first time, the ID will be automatically
generated according to the hardware characteristics and will
not be changed in the future. This TeamViewer ID can
individually access all TeamViewer clients.
Before launching the remote desktop application, make sure
that the tablet is connected to the Internet so that you can
access the tablet to receive remote support from a third party. If
you encounter problems and are not able to solve them, you
could open this application and ask for remote assistance.
To obtain remote support from your partners or XTOOL After-
service Center:
1. Turn on the power of the tablet.

58
2. Click Remote in the diagnosis application. The TeamViewer
screen is displayed, and the device ID will be generated.
3. Your partner must install the remote-control software on
his/her computer by downloading the full version of the
TeamViewer program ([Link] online, and
then start the software on his/her computer at the same time, to
provide support and remote control of the tablet.
4. Provide your ID to the partner or XTOOL technician, and
then wait for him/her to send you a remote-control request.
5. A pop-up window will be displayed, asking you to confirm to
allow the remote-control program to control your device.
6. Click Allow to accept, or click Reject to reject.

Fig 8-1

59
9 FAQ

Q1: FAILED TO GENERATE DIAGNOSIS REPORT

1. Currently only perform diagnostic functions, that is, read
ECU information, read code and clear code, live data,
freeze frame, which can trigger a diagnostic report. Other
functions, such as immobilization and maintenance
services will not be displayed in the report.
2. After entering the diagnosis menu, you need to perform one
specific function before the system can generate a
diagnosis report normally.
3. After the diagnosis is completed, you need to step back to
the previous menu step by step to generate the diagnosis
report successfully. If the APP is killed directly, the report
cannot be triggered.
4. If the report still cannot be generated after troubleshooting
according to the above prompts, please try to exit the APP,
enter the system settings, and then choose to clear the
APP cache.
Enter the path: Setting>>Apps>>Diagnosis>>Clear Cache

Sample as follows:

60
Fig 9-1

Fig 9-2

61
 Fig 9-3

Q2: HOW TO PRINT DIAGNOSIS REPORT

The XTOOL device is compatible with third-party print drivers.
You can download the printer driver you need in the browser
that comes with the tablet to install it, and then set your printer
in the OS settings. After the setting is completed, you can print
it in the Report.

Q3: FAILED TO EXTRACT FILES

Since the XTOOL tablet is equipped with an Android system,
you have to confirm the system type of receiver.
For Android: supports transferring files via Bluetooth, USB
cable, etc.;
62
For IOS: only supports transferring files through a wired
connection (Bluetooth connection is not available).

Q4: MAILBOX SUPPORTED

The diagnosis tablet supports various mailboxes, including
Hotmail, outlook, yahoo and Gmail, etc. When you set up the
email, please make sure that the email client configuration
address you entered is correct.

Q5: HOW TO MAKE AN APPOINTMENT FOR REMOTE

SUPPORT
Please contact your dealer, or send an email to our technical
support center. (Email address: supporting@[Link])
And our technical support team will confirm the time of remote
support with you.

Q6: HOW TO GENERATE AND UPLOAD DIAGNOSTIC LOG

FILES
The D7 tablet will automatically generate and store the
diagnostic logs. When the device is connected to the Internet, it
will automatically upload all the stored diagnostic logs to the
backend system.

63
Q7: HOW TO SWITCH LANGUAGE
1. Contact your dealer and leave a message about the
language you need and the S/N of your device, The
technician will modify the language configuration for you in
the backend system.
2. Settings->Language->Choose language
3. Back to Updates to update all the software again

Q8: FAILED TO DIAGNOSE VEHICLE

1. Contact your dealer to confirm whether the vehicle model is
supported by the scan tool you owned.
2. Check whether the vehicle is properly connected (e.g.
whether the ignition is ON, and the diagnosis of some
vehicle need to turn on the engine ), If your tablet is
equipped with a VCI box, please check the status of VCI
box indicator.
3. Confirm whether you have entered the correct diagnosis
menu.
4. Confirm whether the AUTO-SCAN function can assist you to
enter the correct diagnosis menu, or whether OBDII
function work.
5. Check whether the software is the latest version, if not,
please update to the latest version first.

64
Q9: FAILED TO ACTIVATE OR REGISTER
 For ‘Activation Failed’
Generally caused by network instability, please switch to a
more stable network and try to activate again.

 For ‘Registration Failed’

Generally, it is caused by the connection timeout or the sending
timeout, please check whether you have blocked the outgoing
network traffic to non-US regions like China. We recommend
that you unblock and try to register again.

Q10: FAILED TO TURN ON WHEN CHARGING

In the charging state, you need to first press the power button
to light up the screen(showing the charging status). Then press
and hold the power button for 4-5 seconds until the boot
animation is shown on screen.

Q11: FAILED TO OPEN THE DIAGNOSIS APP

The tablet has to connect to the network every 30 days,
otherwise, the diagnosis app will be locked and disabled until
the device is connected to the network.

65
SHENZHEN XTOOLTECH INTELLIGENT CO., LTD
Company address: 17&18/F, Building A2, Creativity City, Liuxian Avenue,
Nanshan District, Shenzhen, China

Factory address: 2/F, Building 12, Tangtou Third Industrial Zone, Shiyan
Street, Baoan District, Shenzhen, China

Service-Hotline: 0086-755-21670995/86267858

Email: marketing@[Link]

Fax: 0755-83461644

Website: [Link]

66