HPS-1 Plastic anchors

Economical plastic impact anchor

Anchor version Benefits

- Impact anchor for light frames,
battens and profiles on solid base
HPS-1 materials
(M4-M8)
- Impact and temperature resistant
- High quality plastic

Base material

Autoclaved
Concrete
Solid brick Hollow brick aerated
(non-cracked)
concrete

Basic loading data

All data in this section applies to:

- Correct setting (See setting instruction)
- No edge distance and spacing influence
- Base material as specified in the table
- Minimum base material thickness
- Loads shall be reduced if the temperature sustains above 40°C

Recommended loadsa)
5/5- 6/0- 6/30- 8/10- 8/60-
Anchor size 4/0 5/0 8/0
5/15 6/25 6/40 8/40 8/100
NRd [kN] 0,05 0,10 0,15 0,25 0,25 0,30 0,40 0,40
Concrete ≥ C16/20
VRd [kN] 0,15 0,30 0,35 0,55 0,35 0,50 0,90 0,50
Engineering brick, NRd [kN] 0,05 0,10 0,15 0,25 0,25 0,30 0,40 0,40
12 hole, class B VRd [kN] 0,15 0,30 0,35 0,55 0,35 0,50 0,90 0,50
Perforated brick NRd [kN] 0,05 0,10 0,15 0,20 0,20 0,25 0,30 0,30
3 hole common VRd [kN] 0,15 0,30 0,35 0,55 0,35 0,50 0,90 0,55
Thermalite block, NRd [kN] - - 0,08 0,15 0,15 0,20 0,25 0,25
7 N lightweights VRd [kN] - - 0,15 0,25 0,15 0,40 0,40 0,25
Thermalite block, NRd [kN] - - 0,05 0,08 0,08 - 0,12 0,12
1/2 N lightweights VRd [kN] - - 0,10 0,15 0,10 - 0,25 0,15
Autoclaved aerated NRd [kN] - - 0,08 0,10 0,10 - 0,15 0,15
concrete AAC 4, ACC 6 VRd [kN] - - 0,10 0,12 0,10 - 0,30 0,20
Extruded brick, NRd [kN] 0,05 0,10 0,15 0,20 0,20 0,25 0,35 0,35
Boral 10 VRd [kN] 0,15 0,25 0,30 0,40 0,25 0,50 0,90 0,55
a) With overall global safety factor  = 5 to the characteristic loads and a partial safety factor of  = 1,4 to the design values.

1 Updated: Dec-17
 Materials

Material quality
Part Material
Plastic sleeve Polyamide 6.6
Carbon steel, galvanised to min. 5µm
Screw Stainless steel, grade A2
Stainless steel, grade A2, copper-plated

Setting information

Installation temperature
-10 °C to +40°C

Service temperature range

Hilti HPS-1 impact anchor may be applied in the temperature range below.

Base material Max. long term base Max. short term base
Temperature range
temperature material temperature material temperature
Temperature range -40 °C to +80 °C +50 °C +80 °C

Max. short term base material temperature

Short-term elevated base material temperatures are those that occur over brief intervals, e.g. as a result of diurnal
cycling.

Max. long term base material temperature

Long-term elevated base material temperatures are roughly constant over significant periods of time.

Setting details HPS-1

Anchor HPS-1 4 HPS-1 5 HPS-1 6 HPS-1 8
Nominal diameter of drill bit do [mm] 4 5 6 8
Cutting diameter of drill bit dcut ≤ [mm] 4,35 5,35 6,4 8,45
Depth of drill hole h1 ≥ [mm] 25 30 40 50
Nominal embedment depth hnom [mm] 20 20 25 30
Anchor length l [mm] 21,5 22 - 37 27 - 67 28,5 – 132,5
Max fixture thickness tfix [mm] 2 15 40 100

Updated: Dec-17 2
 Installation equipment
Anchor HPS-1 4 HPS-1 5 HPS-1 6 HPS-1 8
Rotary hammer TE2 - TE16
Other tools Screwdriver

Setting parameters HPS-1

Anchor HPS-1 4 HPS-1 5 HPS-1 6 HPS-1 8
Spacing s [mm] 20 25 30 35
Edge distance c [mm] 20 25 30 35

Setting instruction

*For detailed information on installation see instruction for use given with the package of the product.

Setting instructions
1.Drill hole with drill bit 2.Install anchor 3.Hammer in anchor

3 Updated: Dec-17
Updated: Dec-17 4