Manufacturer assumes no responsibility for a hazard or 1.

Features
damage caused by incorrect or non-application of any of the · Accuracy class 1 as per IEC 62053-21, class 0.5, 0.5S, 0.2, 0.2S as per IEC 62053-22
instructions attached herein. Under no circumstance shall · True RMS measurement
Larsen & Toubro be liable for any consequential or resulting
injury or for loss, damage or expense directly or indirectly from · Password protection provision
the use of this product. Sufficient care is taken to provide all · OLD registers to store the previously cleared energy value and Load hours
information regarding the product but Larsen & Toubro does · High / Low V, A, Hz, W, VA, VAr, PF
not claim any responsibility for the damage caused by using the
product directly or indirectly. Use according to the operating · Auto-scaling of Kilo, Mega & Giga value
instructions, professional practices, wiring rules, codes, safety · THD for Voltage and Current
regulations applicable to the given installation. · Site selectable for 3 phase 4 wire, 3 phase 3 wire, 1 phase
Digital Panel Meter · Site programmable CT/PT ratio
During normal operation of this instrument ,hazardous voltages · Maximum demand measurement with real time clock in 4440 series
Multifunction Meter are present at the rear terminals, which can cause injury or · Direct access key for Basic parameters, Power and Energy parameters
Installation ,disconnection or removal of the meter should be
44XX Series LED Type carried out only by qualified, trained personnel, after de-
· Autoscrolling & freeze mode provision is available
energizing connected circuits. Improper installation , including · Terminals with sealing provision (optional)
improper grounding will void warranty. Product warranty void if
seal is broken.

2. Technical Specification
3 Ph 4 W, 3 Ph 3 W, 1 Ph Fast transients burst test ±4 kV as per IEC 61000-4-4
Type of Type Immunity to ±8 kV air discharge, ±6 kV contact
measurement True RMS, 128 samples per cycle,
1 sec update time electrostatic discharge discharge as per IEC 61000-4-2

Electro- Radiated, radio-frequency, 10 V/m as per 61000-4-3

Class 1 as per IEC 62053-21 electromagnetic field immunity test
Measurement magnetic
Accuracy Class 0.5, 0.5s as per IEC 62053-22 compatibility Immunity to electromagnetic HF
Class 0.2, 0.2S as per IEC 62053-22 (EMC) 10 V/m as per IEC 61000-4-6
fields through conducted lines
Display type LED 4 digit for instantaneous and 6 digits
and resolution for cumulative Surge immunity test ±6 kV as per IEC 61000-4-5
50 - 520 VLL Rated power frequency magnetic fields 1 A/m as per IEC 61000-4-8
PT Primary and Secondary user programmable Emission Class B as per CISPR 22
Input voltage for LT and HT applications Impulse voltage test ±6 kV as per IEC 62052-11
Insulation
Burden: 0.2VA max per phase AC voltage test 4 kV double insulation as per IEC 62053-21
properties
-/5A and -/1A site selectable Insulation resistance 500 V DC as per IS 13779
Measuring circuit
Current range from 50mA - 5A with overload Operating temperature -10O C to +55O C
Input current capacity upto 120% In (i.e., 6A) Storage temperature -25O C to +70O C
Operating
CT Primary and Secondary user conditions Humidity 5% to 95% relative humidity non-condensing
programmable for LT and HT applications Recommended wire 2.5 sq mm
Frequency 40 - 70 Hz Shock As per standard IEC 60068-2
Mechanical
Aux voltage 80 - 300VAC/DC Vibration 10 to 55 Hz, 0.15 mm amplitude
conditions
Auxiliary circuit Aux burden <5VA Casing Plastic mould protected to IP51 from front side
Freq range 40 - 70 Hz Measurement category CAT III
Test of power consumption as per IEC 62053-21 Safety Pollution degree 2
Electrical
Voltage dips and interrupts as per IEC 62053-21 Protection IP20 at terminals, IP51 on front
requirements
Short time over current protection 10A max continuous, 20 times of In for 3 sec

3. LED Indication WL 4420

Product weight 300 gms Mega ON M
Weight &
dimensions
Bezel dimension (W x H x D) 96 x 96 x 58 mm
both on
Giga { Kilo ON -
K

Panel cutout 92 x 92 mm +0.8

-0.0
M I/O 1
-

Outputs Meter constant: 10000/(external CT ratio x PT ratio) Lag (ON) K

I/O 2 Digital Outputs
M (If available in meter)
Type RS485 port Modbus RTU -
I/O 3

K I/O 4
Baud rate 2400, 4800, 9600, 19200, 38400 bps (site selectable) M

Parity Odd, Even, None -

Pulse ON
Communication Communication ON K
B P E
Slave id 1 to 247 (programmable) To view parameters CLR PRG
To select and to accept the
2 kVAC isolation for 1 minute between To edit the value/ MULTIFUNCTION METER value/Parameter in setup
Isolation system type downward mode and scroll through
communication and other circuits in edit mode & scroll
To edit the value/system the Energy parameters
type upward in edit mode
through the basic
Certifications CE, RoHS parameters
& scroll through the
Power parameters

4. Display Of Parameters
4.1 Display of Parameters for multifunction meter

Display Meaning Display Meaning Display Meaning

Watts A Current Average High Level of Parameter
UA Total VA F Frequency Low Level of Parameter
Total VAR Neutral Current Voltage THD
PF Power Factor Revolution Per Minute (RPM) Amps hour
Active Energy EB (kWh) Voltage Phase Angle Amps THD
Apparent Energy Current Phase Angle Amps THD Phasewise upto 31st level
Reactive Inductive Energy Unbalance Voltage K-Factor V
Reactive Capacitive Energy Unbalance Current A K-Factor A
Average On Hour Number of Interrupts
Load Hour Old Energy Voltage THD Phasewise upto 31st level
L Lagging Power Factor Clear Baud Rate
ll Voltage Line to Line Rising Demand Active energy delivered / export (kwh)
Voltage Line to Neutral Forecast Demand Leading Power Factor
Voltage RY Phase Maximum Demand
Voltage YB Phase AL Additional Load
Voltage BR Phase Elapse Time

Precautionary Measures to be taken while Wiring the Circuit :

· Turn OFF the power to the circuit, when wiring the circuit. Connecting or removing measurement cables while the power is turned ON is dangerous
· Take special caution not to wire a current measurement circuit to the voltage input terminal or vice-versa
· Strip the insulation cover of the measurement cable so that when it is wired to the input terminal, the conductive parts (bare wires) do not protrude from the terminal.
It is recommended to use appropriate pre lug after crimping the wire. Also, make sure to fasten the input terminal screws securely so that the cable does not come loose
· Use cables with safety terminals that cover the conductive parts for connecting to the voltage input terminals. Using a terminal with bare conductive parts is dangerous if the terminal comes loose
· After connecting the measurement cable, attach the current input protection cover for your safety. Make sure that the conductive parts are not exposed from the protection cover
· Use the suitable star screw driver and apply optimum torque to prevent damage to the meter terminals

Preventive Measures :
· Fuse : To avoid the possibility of short circuit, use a slow blow fuse that has a voltage rating VAC : 250V, Fuse current : 200 mA, Breaking capacity : 10kA@ 125 VAC When replacing a fuse,
turn OFF the power and unplug the power cord. Never short the fuse holder

5.1 Programming Mode 5.2 General Programming Guide 5.3 Setting or Configuration of Parameter If customer enters wrong password
Programming keys · Press UP + E to enter Programming Mode · Press E to enter Edit Mode then pass error will be displayed (Meter
· Press Down to enter Password (Default Value · Blinking of parameter/value indicates Edit Mode is ON will display next parameter
0000) · Press UP or DOWN to increment/decrement values but cannot be edited.) If customer
ENTER - to enter Edit Mode and save parameter
· Digit blinking indicates Edit Mode is ON or to select from available options forgets the set password, Kindly
DOWN - to decrement value or parameter · Press E to accept the value of the parameter contact L&T Customer Interaction Center.
· Press UP or DOWN to increment and
UP - to increment value or parameter · Press DOWN to move to next parameters till end
decrement
after configuration of last parameter display screen
value 0/1/2/3/4/5/6/7/8/9
will prompt “save”, Display reads “y” (YES)
· Press E to edit the next digit till 4th digit · Press Down if changes are not to be saved, display
· If Password is correct, meter displays next reads “ ” (no)
parameter in editable mode · Press E to save the option
5.4 Display : High Limit 1* 1800 1% to 100% of Full scale 5.5. Enabling & Disabling Auto Scrolling
M Press DOWN for 6 secs
Row 1: Parameter -
High Limit 2* 1700 50% to 99% of High Limit 1 Display Shows: EnAbLE Auto.sc
Row 2: Options/Set Option K
Low Limit* 1300 50% to 99% of High limit 2 Again press DOWN for 6 sec
M Display Shows: diSAbL Auto.sc
Eg. Row 1: ConFIG -
Baud rate 9600 2400, 4800, 9600, 19.2k 5.6.Clearing Parameter
K
Row 2: 3P 4W Parity · Press UP + DOWN to enter Clear Mode
Even Even/Odd/none
· Press DOWN to enter Password (0000 Default)
Slave Id 1.000 1 to 247 · Press E to clear
Programming Option/Range · Select :
Default No of Poles (For rpm) - CLR. int to clear integrator (all energy parameter)
Parameter 4.000 1 to 28
- CLR. Hi. L clear max or min value
Yes/No
Reverse lock*** REV.LOC No - CLR. Md clear max demand
ConFIG 3P 4W If YES it blocks energy accumulation
in case the CT polarity reverse. · Once parameter to be cleared is selected it will prompt for
(Defines the power 3P 4W 3P 3W to “Y” (YES) or “ ” (no) for conformation
system configuration.) 1 Phase PASSWORD 0000 0000 to 9999
Energy Resolution Resolution/Counter 5.7. Energy Resolution
100V-999kV
To set 33kV Set first four digits Starting current 0.400 0.4 to 20% of Full Scale Active energy display is available in resolution mode (default) or counter
(3300) as explained above press
PT Primary 415 UP/DOWN key to place decimal point mode.
at appropriate location. Display update time 1.000 1 to 5 seconds
Letter K/M will indicate the Kilo/Mega.
M & K both LED will glow for Giga In Resolution mode when energy reading reaches 9999.xx Wh it will
Display autoscroll time 5.000 1 to 10 seconds
next scale to 10.xxxx kWh, once it reaches 9999.xxkWh it scales to
PT Secondary 415.0 50V to 550V Pulse output on time 250.0 50 to 500 msec 10.xxxxMWh, once it reaches to 9999.xx MWh it scales to 10.xxxx
CT Primary 5.000 0.5A - 99kA GWh.
Analog output 1 VLL/A/Freq/Watts /PF/VA
parameter diSAbL In Counter mode, the energy reading will be fixed at kWh or MWh or
CT Secondary 5.000 0.5A - 6A GWh. It primarily depends on the CT primary and PT primary values.
Method of VA Selection: Analog Output 1 Following table denotes the same:
VA selection VEC.Har Arithmetic /Vector harmonics 0 to 20mA 0 to 20mA/4 to 20mA Full scale
Offset
/Vector ( 3 X PT pri X CT pri ) / 1000 Fixed unit of display
Analog Output 2 VLL/A/Freq/Watts/PF/VA
YEAr** x Range: 2012 to 2052 parameter diSAbL 0.4 - 400 kWh

dAtE** x Jan 01 to December 31 400.1 - 400M MWh

Analog Output 2
0 to 20mA 0 to 20mA/4 to 20mA 400M - 4000M GWh
Time** x 00:00 to 23.59 Offset
*Applicable for 4420 and 4430 Model
Demand Type* Sliding Sliding/Block** **Applicable for 4440 model 5.8. Old Energy
*** not applicable for model 4430
Watts/VAR/A Avg/VA 1. If energy value is reset or CT values are modified,
Demand Parameter* Watts
then the existing energy value will be made zero and
will be saved in another register called
Demand Period* Wh.OLD (old energy).
15 5 - 30 mins

6. Wiring Diagram 7. Memory Map

40101 Watts Total float 40121 PF Y Ph float 40141 VLN Avg float 40161 VAh Received float
Received (Import) Delivered (Export) Received (Import) Delivered (Export) Received (Import) Delivered (Export) 40103 Watts R Ph float 40123 PF B Ph float 40143 V R Ph float 40163 VARh Ind. Received float
40105 Watts Y Ph float 40125 VA Total float 40145 V Y Ph float 40165 VARh Cap. Received float
Load Line Load Line Load Line
40107 Watts B Ph float 40127 VA R Ph float 40147 V B Ph float 40167* Wh Delivered* float
40109 VAR Total float 40129 VA Y Ph float 40149 I Total float 40169* VAh Delivered* float
40151 I R Ph float
4

40111 VAR R Ph float 40131 VA B Ph float 40171* VARh Ind. Delivered* float
3

Relay 2
2

Relay 1
40113 VAR Y Ph float 40133 VLL Avg float 40153 I Y Ph float 40173* VARh Cap. Delivered* float
COM 1

AMF IP
240V AC
AMF IP
240V AC Common

40115 VAR B Ph float 40135 VRY Ph float 40155 I B Ph float 40175 PF Avg. Received float
40117 PF Avg (inst) float 40137 VYB Ph float 40157 Frequency float 40177 Amps hour Received float
3 Phase 4 Wire System 3 Phase 3 Wire System For 4420 and 4430 with 2 relay output
40119 PF R Ph float 40139 VBR Ph float 40159 Wh EB Received float 40179* PF Avg. Delivered* float

40181* Amps hour Delivered* float 40217 Load Hours Received Unsigned long 40265 I Unbal R Ph float 40301 Watts Max. float 40489 I B Har. float
40183 Neutral I float 40219* Load Hours Delivered* Unsigned long 40267 I Unbal Y Ph float 40303 Watts Min. float 40491 K factor V R Ph float
40185 V R Har. float 40221 No of interruptions Unsigned long 40269 I Unbal B Ph float 40305 VAR Max. (absolute max.) float 40493 K factor V Y Ph float
40187 V Y Har. float 40223 MD Occurrence time Unsigned long 40273 Analog input 1 float 40307 VAR Min. (absolute min) float 40495 K factor V B Ph float
40189 V B Har. float 40233 V R Ph angle float 40275 Analog input 2 float 40309 VA Max. float 40497 K factor I R Ph float
40191 I R Har. float 40235 V Y Ph angle float 40285 VLL Max. float 40311 VA Min. float 40499 K factor I Y Ph float
40193 I Y Har. float 40237 V B Ph angle float 40287 VLL Min. float 40313 PF Max. (absolute max.) float 40501 K factor I B Ph float
40195 I B Har. float 40239 I R Ph angle float 40289 VLN Max. float 40315 PF Min. (absolute min.) float *Applicable for 4430 Model
40197 Rising Demand float 40241 I Y Ph angle float 40291 VLN Min. float 40479 V R Har. float
40201 Max. Demand float 40243 I B Ph angle float 40293 Amps Max. float 40481 V Y Har. float
40203* Rising Demand Delivered* float 40259 V Unbal R Ph float 40295 Amps Min. float 40483 V B Har. float
40207* Max. Demand Delivered* float 40261 V Unbal Y Ph float 40297 Frequency Max. float 40485 I R Har. float
40215 RPM float 40263 V Unbal B Ph float 40299 Frequency Min. float 40487 I Y Har. float

8. Mounting Dimensions 9. Troubleshooting

1) Meter display does not turn ON.

Ver 1.1(March 2020)

+2.0
Steps for Mounting
90 Insert meter to panel In case of complaint please contact
- 0.0
1 a) Check that there is power supply applied on Aux supply terminals.
without clamps
b) Check fuse connection (Use fuse connection of specified ratings). CUSTOMER INTERACTION CENTRE (CIC)
2 2) Data displayed / reading incorrect. TOLL-Free: 1800 233 5858, 1800 200 5858
Insert both clamps
1 3 a) Check that CT /PT ratios are properly set. Telephone : 022 6774 5858
2 email: [email protected]
b) Check if proper configuration mode 3P4W, 3P3W, 1Phase is correctly set.
90 +2.0
- 0.0
3) Pt reading are incorrect / Active Power reading is negative.
a) CT connections may be reversed, check and correct CT connection.
b) Check voltage and current phases are connected in proper sequence.
4) RS485 communication does not work.
a) Check baud rate & parity maintained in the connected computers is same as meter.
54mm b) Memory mapping in software is correct.
3
4mm c) Check Slave ID of meter is Unique & properly maintained. L&T Electrical & Automation
d) Check converter is working properly. Electrical Standard Products
e)Ensure termination resistor (120Ω 0.5W)is connected L&T Business Park, Tower 'B' / 3rd Floor
Saki Vihar Road, Powai Mumbai 400 072
Website: www.Lntebg.com
 Manufacturer assumes no responsibility for a hazard or 1. Features
damage caused by incorrect or non-application of any of the
instructions attached herein. Under no circumstance shall
· Accuracy class 1 as per IEC 62053-21, · Direct access key for basic parameters, Power and
Larsen & Toubro be liable for any consequential or resulting class 0.5, 0.5S, 0.2, 0.2S as per IEC 62053-22 Energy parameters
injury or for loss, damage or expense directly or indirectly from
the use of this product. Sufficient care is taken to provide all · True RMS measurement · Autoscrolling & freeze mode provision is available
information regarding the product but Larsen & Toubro does · Password protection provision · Terminals with sealing provision (optional)
not claim any responsibility for the damage caused by using the
product directly or indirectly. Use according to the operating
· OLD registers to store the previously · Favourite screen option for user selectable
instructions, professional practices, wiring rules, codes, safety cleared energy value and Load hours parameters
regulations applicable to the given installation. · High/Low V, A, Hz, W, VA, VAr, PF · Phase wise Voltage and Current waveforms
Digital Panel Meter · Auto-scaling of Kilo, Mega & Giga value · Power saving mode
Multifunction Meter
During normal operation of this instrument ,hazardous voltages · THD for Voltage and Current
are present at the rear terminals, which can cause injury or
Installation ,disconnection or removal of the meter should be · Site selectable for 3 Ph 4 W, 3 Ph 3 W, 1 Ph
44XX Series LCD Type carried out only by qualified, trained personnel, after de- · Site programmable CT/PT ratio
energizing connected circuits. Improper installation , including · Maximum demand measurement with
improper grounding will void warranty. Product warranty void if
seal is broken. real time clock in 4440 series

2. Technical Specification
3 P 4 W, 3 P 3 W, 1 P Impulse voltage test ±6 kV as per IEC 62052-11
Insulation
Type of Type AC voltage test 4 kV double insulation as per IEC 62053-21
measurement True RMS, 128 samples per cycle, properties
1 sec update time Insulation resistance 500 V DC as per IS 13779
Operating temperature -10O C to +55O C
Class 1 as per IEC 62053-21
Measurement Operating Storage temperature -25O C to +70O C
Accuracy Class 0.5, 0.5s as per IEC 62053-22
conditions Humidity 5% to 95% relative humidity non-condensing
Class 0.2, 0.2s as per IEC 62053-22
Recommended wire 2.5 sq mm
Display type LCD 4 digit for instantaneous and 6 digits
and resolution for cumulative Shock As per standard IEC 60068-2
Mechanical
50 - 520 VLL Vibration 10 to 55 Hz, 0.15 mm amplitude
conditions
PT Primary and Secondary user programmable Casing Plastic mould protected to IP51 from front side
Input voltage for LT and HT applications Measurement category CAT III
Burden: 0.2VA max per phase Safety Pollution degree 2
-/5A and -/1A site selectable Protection IP20 at terminals, IP51 on front
Measuring circuit 300 gms
Current range from 50mA - 5A with overload Product weight
Input current capacity upto 120% In (i.e., 6A) Weight & Bezel dimension (W x H x D) 96 x 96 x 58 mm
dimensions
CT Primary and Secondary user Panel cutout 92 x 92 mm +0.8
-0.0
programmable for LT and HT applications Outputs Meter constant: 10000/(external CT ratio x PT ratio)
Frequency 40 - 70 Hz Type RS485 port Modbus RTU
Aux voltage 80 - 300VAC/DC Baud rate 2400, 4800, 9600, 19200, 38400 bps (site selectable)
Auxiliary circuit Aux burden <5VA Parity Odd, Even, None
Communication
Freq range 40 - 70 Hz Slave id 1 to 247 (programmable)
Test of power consumption as per IEC 62053-21 2 kVAC isolation for 1 minute between
Electrical Isolation
Voltage dips and interrupts as per IEC 62053-21 communication and other circuits
requirements
Short time over current protection 10A max continuous, 20 times of In for 3 sec Certifications CE, RoHS
Fast transients burst test ±4 kV as per IEC 61000-4-4

Immunity to electrostatic discharge ±8 kV air discharge, ±6 kV contact

discharge as per IEC 61000-4-2
Radiated, radio-frequency, 10 V/m as per 61000-4-3
Electro- electromagnetic field immunity test
magnetic Immunity to electromagnetic HF
compatibility 10 V/m as per IEC 61000-4-6
fields through conducted lines
(EMC)
Surge immunity test ±6 kV as per IEC 61000-4-5

Rated power frequency magnetic fields 1 A/m as per IEC 61000-4-8

Emission Class B as per CISPR 22

3. LED Indication WC 4410 WC 4410 WC 4410

Four parameter Three user selectable parameters available in

415.0 LL 5.000 A view display
415.0 LL 5.000 A single screen Wh is fixed and any two
0.000 Ay
230.0 Ln 50.00 F 230.0 Ln 50.00 F parameters selectable from 0.000 Ln FAV
Wh Wh W,F,A,VLL,Ab,Ay,Ar,VA,PF Wh
Digital Outputs Fixed for quick
1234.567 (if available in meter) view of energy 1234.567 Disable Auto scroll mode and switch to Fav 1234.567
parameter always screen using Options button
I/0 I/0 I/0
Communication ON 1 2 3 4
Pulse ON 1 2 3 4 1 2 3 4

B P E B P E B P E
To view parameters CLR PRG CLR PRG CLR PRG
To select and to accept the
MULTIFUNCTION METER value/Parameter in setup MULTIFUNCTION METER MULTIFUNCTION METER
To edit the value/ mode and scroll through
system type downward To edit the value/system the Energy parameters
in edit mode & scroll type upward in edit mode
through the basic & scroll through the
parameters Power parameters

4. Display Of Parameters
4.1 Display of Parameters for multifunction meter

Display Meaning Display Meaning Display Meaning

W Watts A Current Average HI High Level of Parameter
VA Total VA F Frequency Lo Low Level of Parameter
Vr Total VAR An Neutral Current V.thd Voltage THD
PF Power Factor RPM Revolution Per Minute (RPM) Ah Amps hour
Wh Active Energy Received ( kWh) V.Ph.ANG Voltage Phase Angle A.thd Amps THD
VAh Apparent Energy A.Ph.ANG Current Phase Angle K.FACt.U. K-Factor V
VArh.L Reactive Inductive Energy Un.BAL.V Unbalance Voltage K.FACt.A. K-Factor A
VArh.C Reactive Capacitive Energy Un.BAL.A Unbalance Current lntr Number of Interrupts
AVG Average On.hr On Hour b Baud Rate
Ld.Hr. Load Hour OLD Old d Active energy Delivered (Export) (kwh)
L Lagging Power Factor CLr Clear C Leading Power Factor
LL Voltage line to line rd Rising Demand
Ln Voltage line to Neutral Fd Forecast Demand
rY Voltage RY Phase Md Maximum Demand
Yb Voltage YB Phase AL Additional Load
br Voltage BR Phase Et Elapse Time

Precautionary Measures to be taken while Wiring the Circuit :

· Turn OFF the power to the circuit, when wiring the circuit. Connecting or removing measurement cables while the power is turned ON is dangerous
· Take special caution not to wire a current measurement circuit to the voltage input terminal or vice-versa
· Strip the insulation cover of the measurement cable so that when it is wired to the input terminal, the conductive parts (bare wires) do not protrude from the terminal.
It is recommended to use appropriate pre lug after crimping the wire. Also, make sure to fasten the input terminal screws securely so that the cable does not come loose
· Use cables with safety terminals that cover the conductive parts for connecting to the voltage input terminals. Using a terminal with bare conductive parts is dangerous if the terminal comes loose
· After connecting the measurement cable, attach the current input protection cover for your safety. Make sure that the conductive parts are not exposed from the protection cover
· Use the suitable star screw driver and apply optimum torque to prevent damage to the meter terminals

Preventive Measures :
· Fuse : To avoid the possibility of short circuit, use a slow blow fuse that has a voltage rating
VAC : 250V, Fuse current : 200 mA, Breaking capacity : 10kA@ 125 VAC When replacing a fuse,
turn OFF the power and unplug the power cord. Never short the fuse holder
5.1 Programming Mode 5.2 General Programming Guide 5.3 Setting or Configuration of Parameter If customer enters wrong password
Programming keys · Press UP + E to enter Programming Mode · Press E to enter Edit Mode then pass error will be displayed (Meter
· Press Down to enter Password (Default Value · Blinking of parameter/value indicates Edit Mode is ON will display next parameter
0000) · Press UP or DOWN to increment/decrement values but cannot be edited.) If customer
ENTER - to enter Edit Mode and save parameter or to select from available options forgets the set password, Kindly
DOWN - to decrement value or parameter · Digit blinking indicates Edit Mode is ON
· Press E to accept the value of the parameter contact L&T Customer Interaction Center.
UP - to increment value or parameter · Press UP or DOWN to increment and · Press DOWN to move to next parameters till end
decrement after configuration of last parameter display screen
value 0/1/2/3/4/5/6/7/8/9 will prompt “save”, Display reads “y” (YES)
· Press E to edit the next digit till 4th digit · Press Down if changes are not to be saved, display
· If Password is correct, meter displays next reads “ ” (no)
parameter in editable mode · Press E to save the option

CONFIG ROW 1: Parameter Pulse POP.ON.T

5.4 Display : 3P.4W
ROW 2: Options /Set options Demand Type* Sliding Sliding/Block** 250.0 50 to 500 msec
output on time
Programming Parameter Option/Range Demand Parameter* Watts Watts/VAR/A Avg/VA Analog Output 1
Default VLL/A/Freq/Watts/PF/VA
parameter AO.1.PAR diSAbL
CONFIG 3P 4W Demand Period* 15 5 - 30 mins
(Defines the power 3P 4W 3P 3W Analog Output 1
High Limit 1* 1800 1% to 100% of Full scale 0 to 20mA 0 to 20mA/4 to 20mA
system configuration.) 1 Phase Offset AO.1.OFS
100V-999kV High Limit 2* 1700 50% to 99% of High Limit 1 Analog Output 2
To set 33kV Set first four digits parameter AO.2.PAR diSAbL VLL/ A/ Freq/ Watts/ PF/ VA
(3300) as explained above press
PT Primary 415 UP/DOWN key to place decimal point Low Limit* 1300 50% to 99% of High limit 2
Analog Output 2
at appropriate location.
Offset AO.2.OFS 0 to 20mA 0 to 20mA/4 to 20mA
Letter K/M will indicate the Kilo/Mega. 2400, 4800, 9600, 19.2k
M & K both LED will glow for Giga Baud rate BAUD 9600
Power PWR.SAV Disable Disable/ Enable
PT Secondary 415.0 50V to 550V Parity PARITY Even Even/ Odd/ none saver mode
CT Primary 5.000 0.5A - 99kA Slave Id SL.Id 1.000 1 to 247 *Applicable for 4420 and 4430 Model
**Applicable for 4440 model 5.7. Old Energy
*** not applicable for model 4430 1. If energy value is reset or
CT Secondary 5.000 0.5A - 6A
No of Poles (For rpm) 4.000 1 to 28 5.5. Enabling & Disabling Auto Scrolling CT values are modified,
then the existing energy
Method of VA Selection: Press DOWN for 6 secs value will be made zero and
VA selection VEC.Har Arithmetic /Vector harmonics Yes/No Display Shows: EnAbLE Auto.sc will be saved in another
/Vector Reverse lock*** REV.LOC No If YES it blocks energy register called
accumulation in case the CT Again press DOWN for 6 sec
Wh.OLD (old energy).
Options: Watts/FREQ/A/ polarity reverse. Display Shows: diSAbL Auto.sc
Programmable
Watts VLL/Ab/Ay/Ar/VA/PF 5.6.Clearing Parameter
Parameter 1 PARAM 1 PASSWORD PASWd 0000 0000 to 9999 · Press UP+ DOWN to enter Clear Mode
Programmable Options: Watts/FREQ/A/ · Press DOWN to enter Password (0000 Default)
PF VLL/Ab/Ay/Ar/VA/PF Energy ENERGY Resolution Resolution/ Counter · Press E to clear
Parameter 2 PARAM 2
· Select :
YEAr** x Range: 2012 to 2052 Starting Current START.A 0.400 0.4 to 20% of Full Scale -CLR. int to clear integrator (all energy parameter)
-CLR. Hi. L clear max or min value
x -CLR. Md clear max demand
dAtE** Jan 01 to December 31 Display update time DISP.U.R 1.000 1 to 5 seconds · Once parameter to be cleared is selected it prompt
Time** x 00:00 to 23.59 Display autoscroll Time Auto.T 5.000 1 to 10 seconds to “Y” (YES) or “ ” (no) for conformation

5.7. Energy Resolution

Active energy display is available in resolution mode (default) or counter 6. Wiring Diagram
mode.
In Resolution mode when energy reading reaches 9999.xx Wh it will Received (Import) Delivered (Export) Received (Import) Delivered (Export) Received (Import) Delivered (Export) Received (Import) Delivered (Export)

next scale to 10.xxxx kWh, once it reaches 9999.xxkWh it scales to

10.xxxxMWh, once it reaches to 9999.xx MWh it scales to 10.xxxx GWh. Load Line Load Line Load Line Load Line
In Counter mode, the energy reading will be fixed at kWh or MWh or
GWh. It primarily depends on the CT primary and PT primary values.

4
Following table denotes the same:

3
Relay 2

2
Relay 1
Full scale

COM 1
AMF IP AMF IP AMF IP
Common
( 3 X PT pri X CT pri ) / 1000 Fixed unit of display
240V AC 240V AC 240V AC

0.4 - 400 kWh

400.1 - 400M MWh 3 Phase 4 Wire System 3 Phase 3 Wire System Single Phase System For 4420 and 4430 with 2 relay output
400M - 4000M GWh

7. Memory Map
Address Parameter Data type Address Parameter Data type Address Parameter Data type Address Parameter Data type
40101 Watts Total float 40157 Frequency float 40223 MD Occurrence time Unsigned long 40315 PF Min. (absolute min.) float
40103 Watts R Ph float 40159 Wh Received float 40233 V R Ph angle float 40479 V R Har. float
40105 Watts Y Ph float 40161 VAh Received float 40235 V Y Ph angle float 40481 V Y Har. float
40107 Watts B Ph float 40163 VARh Ind. Received float 40237 V B Ph angle float 40483 V B Har. float
40109 VAR Total float 40165 VARh Cap. Received float 40239 I R Ph angle float 40485 I R Har. float
40111 VAR R Ph float 40167** Wh Delivered float 40241 I Y Ph angle float 40487 I Y Har. float
40113 VAR Y Ph float 40169** Vah Delivered float 40243 I B Ph angle float 40489 I B Har. float
40115 VAR B Ph float 40171** VARh Ind. Delivered float 40259 V Unbal R Ph float 40491 K factor V R Ph float
40117 PF Avg (inst) float 40173** VARh Cap. Delivered float 40261 V Unbal Y Ph float 40493 K factor V Y Ph float
40119 PF R Ph float 40175 PF Avg. Received float 40263 V Unbal B Ph float 40495 K factor V B Ph float
40121 PF Y Ph float 40177 Ampere Hour float 40265 I Unbal R Ph float 40497 K factor I R Ph float
40123 PF B Ph float 40179** PF Avg. Delivered float 40267 I Unbal Y Ph float 40499 K factor I Y Ph float
40125 VA Total float 40181** Ampere Hour Delivered float 40269 I Unbal B Ph float 40501 K factor I B Ph float
40127 VA R Ph float 40183 Neutral Current float 40285 VLL Max. float ** Applicable for 4430 Model

40129 VA Y Ph float 40185 V R Har. float 40287 VLL Min. float

40131 VA B Ph float 40187 V Y Har. float 40289 VLN Max. float
40133 VLL Avg float 40189 V B Har. float 40291 VLN Min. float
40135 VRY Ph float 40191 I R Har. float 40293 Amps Max. float
40137 VYB Ph float 40193 I Y Har. float 40295 Amps Min. float
40139 VBR Ph float 40195 I B Har. float 40297 Frequency Max. float
40141 VLN Avg float 40197 Rising Demand float 40299 Frequency Min. float
40143 V R Ph float 40201 Max. Demand float 40301 Watts Max. float
40145 V Y Ph float 40203** Rising Demand Delivered float 40303 Watts Min. float
40147 V B Ph float 40207** Max. Demand Delivered float 40305 VAR Max. (absolute max.) float
40149 I Total float 40215 RPM float 40307 VAR Min. (absolute min) float
40151 I R Ph float 40217 Load Hours Received Unsigned long 40309 VA Max. float
40153 I Y Ph float 40219** Load Hours Delivered Unsigned long 40311 VA Min. float
40155 I B Ph float 40221 No of interruptions Unsigned long 40313 PF Max. (absolute max.) float

8. Mounting Dimensions : 9. Troubleshooting

Ver 1.1(March 2020)

1) Meter display does not turn ON. In case of complaint please contact
+2.0 Steps for Mounting
90 - 0.0
Insert meter to panel
a) Check that there is power supply applied on Aux supply terminals. CUSTOMER INTERACTION CENTRE (CIC)
1
without clamps b) Check fuse connection (Use fuse connection of specified ratings). TOLL-Free: 1800 233 5858, 1800 200 5858
2) Data displayed / reading incorrect. Telephone : 022 6774 5858
2 Insert both clamps
1
a) Check that CT /PT ratios are properly set. email: [email protected]
2 3
b) Check if proper configuration mode 3P4W, 3P3W, 1Phase is correctly set.
90 +2.0 3) Pt reading are incorrect / Active Power reading is negative.
- 0.0
a) CT connections may be reversed, check and correct CT connection.
b) Check voltage and current phases are connected in proper sequence.
4) RS485 communication does not work. L&T Electrical & Automation
a) Check baud rate & parity maintained in the connected computers is same as Meter. Electrical Standard Products
b) Memory mapping in software is correct. L&T Business Park, Tower 'B' / 3rd Floor
54mm
3 c) Check Slave ID of meter is Unique & properly maintained. Saki Vihar Road, Powai Mumbai 400 072
4mm
d) Check converter is working properly. Website: www.Lntebg.com
e)Ensure termination resistor (120Ω 0.5W)is connected