NV11

MANUAL SET

Downloaded from www.Manualslib.com manuals search engine

 NV11
MANUAL SET

INTRODUCTION

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set - Introduction 1

MANUAL AMENDMENTS

Document Base Details

Spec. Used Issue Receipt Comments

Date Date
GA963-1 09/09/10 29/07/11
GA138 01/11/10 22/01/11
GA959 29/03/11 29/07/11

Amendment Details

Rev. Date Amendment Details Issued by

-- 19/04/12 First Issue EAM

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set - Introduction 2

NV11 MANUAL SET - INTRODUCTION

COPYRIGHT 3
LIMITED WARRANTY 3
PRODUCT SAFETY INFORMATION 3
INTRODUCTION 4
FEATURES 5
TYPICAL APPLICATIONS 5
STRUCTURE OF THIS MANUAL SET 6
WHICH SECTION IS RELEVANT TO ME? 6

MAIN HEADQUARTERS Innovative Technology Ltd

Derker Street – Oldham – England - OL1 4EQ
Tel: +44 161 626 9999 Fax: +44 161 620 2090
E-mail: [email protected]
Web site: www.innovative-technology.co.uk

BRAZIL
[email protected]

CHINA
[email protected]

GERMANY
[email protected]

SPAIN
[email protected]

UNITED KINGDOM
[email protected]

UNITED STATES OF AMERICA

[email protected]

REST OF THE WORLD

[email protected]

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set - Introduction 3

COPYRIGHT

This manual set is Copyright © Innovative Technology Ltd. 2012. No part of this
publication may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from
Innovative Technology Ltd. The contents of this manual set may be subject to change
without prior notice.

LIMITED WARRANTY

Innovative Technology Ltd warrants each of its hardware products to be free from
defects in workmanship and materials under normal use and service for a period
commencing on the date of purchase from Innovative Technology Ltd or its
Authorized Reseller, and extending for the length of time stipulated by Innovative
Technology Ltd.

A list of Innovative Technology Ltd offices can be found in every section of this
manual set. If the product proves defective within the applicable warranty period,
Innovative Technology Ltd will repair or replace the product. Innovative Technology
Ltd shall have the sole discretion whether to repair or replace, and any replacement
product supplied may be new or reconditioned.

The foregoing warranties and remedies are exclusive and are in lieu of all other
warranties, expressed or implied, either in fact or by operation of law, statutory or
otherwise, including warranties of merchantability and fitness for a particular purpose.

Innovative Technology Ltd shall not be liable under this warranty if it’s testing and
examination disclose that the alleged defect in the product does not exist or was
caused by the customer's or any third person's misuse, neglect, improper installation
or testing, unauthorized attempts to repair, or any other cause beyond the range of
the intended use. In no event will Innovative Technology Ltd be liable for any
damages, including loss of profits, cost of cover or other incidental, consequential or
indirect damages arising out the installation, maintenance, use, performance, failure
or interruption of a Innovative Technology Ltd product, however caused.

PRODUCT SAFETY INFORMATION

Throughout this manual set, we may draw your attention to key safety points that you
should be aware of when using or maintaining the product.

These safety points will be highlighted in

a box, like this: Caution!
Mains voltage is present on
these terminals

This manual set and the information it contains is only applicable to the model stated
on the front cover, and must not be used with any other make or model.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set - Introduction 4

INTRODUCTION

The NV11 validator is made up of four basic components: an NV9USB validator head,
Note Float module, removable bezel and a cashbox (as shown below):

Note Float
module

Removable
bezel

NV9USB
validator
head

Cashbox

The NV11 is a device that can accept, validate and store 300 or 600 bank notes of
mixed denominations, and also has the capability of storing a further 30 notes in the
Note Float module for future payout.

NV11 NV11 NV11

Rear View Side View Front View

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set - Introduction 5

Up to 16 different denominations of bank note can be accepted and stacked, and the
Note Float module can be programmed to store and dispense 30 single denomination
notes.

The NV11 validator leaves the factory preset to at least one currency and one
firmware interface so that it is ready for immediate installation. The NV11 validator
works with any NV9USB currency dataset created by Innovative Technology Ltd -
datasets can be downloaded from the Support section of the ITL website.

FEATURES

The NV11 validator has many innovative features, including:

 300 or 600 note storage capacity

 Note Float module has 30 note capacity (single denomination)
 Accepts, validates and stores bank notes in less than 3 seconds
 Uses a secure encrypted protocol for data transfer

TYPICAL APPLICATIONS

The NV11 validator can be used in a variety of situations where high security and high
volume bank note acceptance, validation and payout are needed. Some typical
applications are:

 AWP and SWP applications

 Self-Serve and Retail
 Kiosks
 Casinos
 Parking and Ticketing
 Vending

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set - Introduction 6

STRUCTURE OF THIS MANUAL SET

This manual set is made up of seven sections, each is supplied in a separate Portable
Document Format (PDF) file, so you only need to download or print the section
relevant to your requirements:

 Introduction
 Section 1 – Quick Start and Configuration Guide
 Section 2 – Field Service Manual
 Section 3 – ITL Software Support Guide
 Section 4 – Mechanical and Electrical Manual
 Section 5 – Software Implementation Guide
 Section 6 – Technical Appendices

WHICH SECTION IS RELEVANT TO ME?

 Quick Start and Configuration Guide:

– Most users should use this section; typical users are software engineers
looking at how to make it work, project engineers evaluating their first
unit, or installation engineers installing the unit into a host machine.

– This section contains the essential information that a user needs to

quickly assemble and configure the NV11 validator ready for installation
into the host machine.

 Field Service Manual:

– Typically used by a field service engineer who is maintaining the

product.

– This section contains the essential information that the field service
engineer needs to clean, maintain and fault find an NV11 validator that
is installed in a host machine.

 ITL Software Support Guide:

– Any user who wants to test the functionality of the unit, reprogram the
firmware or dataset, or set up the encryption key, address or routing for
the unit.

– This section contains the information needed for a user to configure and
program the NV11 validator, using a range of software tools.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set - Introduction 7

 Mechanical and Electrical Manual:

– Design engineers who are designing a host machine cabinet, or looking

to integrate the NV11 validator into an existing cabinet.

– This section contains the all the mechanical and electrical information a
designer needs to effectively integrate the NV11 validator into a host
machine.

 Software Implementation Guide:

– Software engineers looking at how to implement the NV11 validator in

their host machine, or design engineers looking at including the unit in
their host machine.

– The information in this section details the communications protocols,

specific commands and interfaces used (eSSP and ccTalk).

 Technical Appendices:

– These appendices have no specific audience, but users can find relevant
and useful information here.

– This section includes information on product approvals, technical

specifications and ordering information.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 SECTION 1
NV11
MANUAL SET

QUICK START
AND
CONFIGURATION
GUIDE

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 1 2

NV11 MANUAL SET – SECTION 1

1. QUICK START AND CONFIGURATION GUIDE 3

1.1 Assembly 3
1.2 Bezel Removal and Refitting 6
1.3 Interfacing 7
1.4 Connector and Pinouts 8
1.5 Configuration 9
1.6 Status Indicators 10
1.7 Programming 10
1.8 Technical Specifications 11
1.9 NV11 Flash Codes 12
1.10 Fault Finding 14
1.11 Frequently Asked Questions 16

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 1 3

1. QUICK START AND CONFIGURATION GUIDE

This section is one part of a complete manual set: most users should use this section
of the manual - typical users are software engineers looking at how to make it work,
project engineers evaluating their first unit, or installation engineers installing the unit
into a host machine.

This section contains the essential information that a user needs to quickly assemble
and configure the NV11 validator ready for installation into the host machine.

The NV11 validator is pin for pin compatible with

Information
the NV7 / NV8 / NV9 / NV10 series of validators,
Validator compatibility. but NOT with earlier versions of the product
(NV2 – NV5).

1.1 Assembly

Installing the NV11 is a simple operation, but note that the validator can only be
installed horizontally:

1. If the validator head

Blanking plate
has a blanking plate
fitted, you will need
to remove this
BEFORE attempting to
fit the Note Float
module. If the Note
Float module is
already fitted, please
Validator head
go to step 6
2. Open the validator
head by sliding the
red release catch on
the front of the
validator to the left
(as indicated in the
picture)

Release catch

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 1 4

Caution! Always make sure the validator head has been

opened BEFORE trying to remove the blanking
Validator head MUST be plate – trying to remove the blanking plate with
opened. the validator head closed will cause unit
damage.

Side clips
3. Remove the blanking
plate by disengaging
the two side clips and
lifting the blanking
plate upwards

4. Close the validator

head and then
carefully fit the Note Rear cover
Float module onto the
validator head,
making sure the rear
cover is securely
closed and that both
latches are lined up
correctly

Latch

5. Make sure both

latches are engaged
and closed

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 1 5

6. The validator can be

fitted with a standard
or slide-on cashbox of
300 or 600 note
capacity

7. If not already
attached, the
validator can be fitted
with a horizontal
bezel of your choice.

8. The cashbox is
Note Float module
attached to the
validator by locating
and sliding until the
cashbox is clipped Bezel
securely and secured
in the host machine
using the studs on the
bottom of the
cashbox
Validator
head

Mounting
Cashbox studs

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 1 6

There are many variants of bezel and cashbox type

Information
available for the NV11 validator. Please check the ITL
Check website for options. website (www.innovative-technology.co.uk) for up to
date information on the options available.

1.2 Bezel Removal and Refitting

b. Slide bezel away from

 The bezel is locking arms
removed by pushing
the red locking arms
on both sides of the
validator upwards,
and sliding the bezel
away from the
locking arms

a. Push locking arms upwards

Lift upwards to remove

 Lift the bezel off
once the bezel has
been slid fully
across and is clear
of the locating pins

Locating pins

The bezel is refitted by pushing the bezel back onto the locating pins and sliding
backwards until all six pins are engaged in the slots. The locking arms will then spring
back and locate into the bezel.

Caution! Always make sure that BOTH locking arms are

fully located in the bezel – trying to operate the
Check locking arms. validator if they are not correctly located can
cause unit damage.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 1 7

1.3 Interfacing

The connector needed to set up and interface with the NV11 validator is easily
accessible on the side of the unit:

Interface
Connector

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 1 8

1.4 Connector and Pinouts

The NV11 validator has a single connector that is used to allow interfacing and
programming.

Information
Power is always required on pins 15 and 16 of the
Power always required 16 way connector.
regardless of connection
type.

The connector is a 16 pin socket used to interface the NV11 to the host machine. The
pin numbering of the socket is shown below, as well as an overview of the socket
connections:

Pin Description
1 Serial Data Out (Tx)
5 Serial Data In (Rx)
11 USB Data +
12 USB Data -
13 USB Power (+5V)
15 +V
16 0V / Ground Connection

To use a USB connection with the NV11, a USB cable fitted with a 16 way connector
on one end (ITL Part Number CN392) should be used. The CN392 cable fits into the
16 way connector and allows high speed programming and serial communications
when used in SSP and ccTalk modes.

When using the USB connection, power must be supplied to the NV11 using the
CN392 cable.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 1 9

1.5 Configuration

The NV11 does not use DIP switches to configure the unit – configuration and setting
is carried out by using a Configuration Button mounted on the front of the Note Float
module:

Note Float module

Configuration Button

Status LED

There are several functions available when using the Configuration Button, and these
are listed in this table:

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 1 10

Action Power Status Function

Press and hold (more than Powered ON Sets validator to Programming
2 seconds) until the bezel mode (SSP)
illuminates, then release
Press twice (within half a Powered ON Shows current interface type (see
second) flash count table below)
Press once when Note Powered ON Acknowledges that a note
Float module status LED is blockage has been cleared
flashing (transport error)

Flash Count Interface The NV11 Validator leaves the factory preset
1 SSP to at least one currency and one interface so
6 ccTalk that it is ready for immediate installation. The
6,1 ccTalk plain (16 bit) dataset and interface used are shown on the
6,1,2 ccTalk (8 bit) label fixed to the front of the Note Float unit.

1.6 Status Indicators

The NV11 validator has two separate coloured Light Emitting Diode (LED) indicators
that are used to show the status of the unit – these are located next to the
configuration button on the front of the Note Float module, and behind the front bezel
of the NV9USB validator head.

If there is a fault or other issue with the unit, the LEDs will flash as described in
subsection 1.9.

1.7 Programming

Full details on programming the NV11 validator can be found in Section 3 of this
manual set (ITL Software Support Guide).

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 1 11

1.8 Technical Specifications

The full technical specifications for the NV11 validator can be found in Section 6,
Appendix B of this manual set. A brief summary is given here:

DC Voltage Minimum Nominal Maximum

Absolute limits 10.8 V 12 V 13.2 V
Supply ripple voltage 0V 0V 0.25 V @ 100 Hz
Supply Current
Standby 350 mA
Running 3A
Peak (motor stall) 3.5 A

Interface Logic Levels Logic Low Logic High

Inputs 0 V to +0.5 V +3.7 V to +12 V
Outputs (2.2 kΩ pull-up) +0.6 V Pull-up voltage of host
interface
Maximum current sink 50 mA per output

WARNING! Ensure that the supply voltage to the NV11 is not

lower than 10.8 V and that the power supply can
Use suitable power supply
provide sufficient current to avoid incorrect
operation and excessive note rejects.

We recommend that your power supply is capable of supplying 12V DC at 4 A.

 For 12V operation, use TDK Lambda model SWS50-12. This power supply is
available from a variety of suppliers including Farnell (stock code 1184645) and
RS (stock code 466-5869).

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 1 12

1.9 NV11 Flash Codes

The NV11 validator has inbuilt fault detection facilities. If there is a configuration or
other error either the Note Float module status LED, or the NV9USB validator head
front bezel will flash in a particular sequence; a summary of the Flash Codes for both
units is shown below:

NV9USB Bezel Flash Codes:

Flashes Indicated Error Comments

Long Short
0 0 None
Remove obstruction and
follow the cleaning
2 Note path obstructed
procedure in Section 2 of
1
this manual set
Contact ITL technical
3 Unit not initialised
support
Check that the cash box
note plate is free to move
2 2 Cash box problem
and the stacker mechanism
is in the home position
Firmware checksum
1
error
Interface checksum
error or unable to
2
set programmed
Download new firmware
interface
3 EEPROM checksum
3
error
Dataset checksum
4
error
Check the validator
Incompatible
5 firmware is compatible with
firmware
the Note Float module
Power supply too
1
low
4 Check power supply
Power supply too
2
high

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 1 13

Note Float Module Flash Codes:

Flashes Indicated Error Comments

0 None
Constant Remove trapped note from the
flash Note Float module and press
Note transport error
(1 every the configuration button once
second)
Download new dataset /
2 Software error
firmware
Return to service centre for
3 Calibration error
repair
Check for trapped notes
4 Diverter error stopping the diverter returning
to the home position
Check for trapped notes
5 Motor timeout stopping the Note Float module
tape from moving

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 1 14

1.10 Fault Finding

Please use this flow chart with the Flash Codes in the previous sub-section as an aid
to help resolve any configuration or start up problems you might have after installing
the NV11 validator

Check the required dataset is programmed using the

Incorrect currency
Validator Manager Software (see Section 3 of this
file
manual set).

Check the required note denomination and issue is

Notes not included in
included in the currency file using the Validator Manager
currency file
Software (see Section 3 of this manual set).
All notes rejected
(bezel LEDs ON)
Check the host machine is ready to accept notes and
Notes inhibited by
that the maximum allowed credit hasn’t been exceeded.
host machine
If a coin hopper is fitted, make sure it isn’t empty.

Check there is sufficient clearance for note ejection after

Bill path obstructed
acceptance (see Section 4 of this manual set).

Check there is power to the validator, and that it is

within the tolerances specified in the Technical
No power
Specification (see subsection 1.8 or Section 6 of this
manual set).
Notes not accepted
(bezel LEDs OFF) Check which interface the validator is programmed for by
Incorrect interface pressing the configuration button twice – the displayed
programmed code indicates which interface is programmed (see
subsection 1.5 of this manual).

Check voltage and current supplied to the validator are

within the tolerances specified in the Technical
Specification (see subsection 1.8 or Section 6 of this
Power supply out of
manual set).
specification
Check there is sufficient clearance for note ejection after
Notes accepted but
acceptance (see Section 4 of this manual set).
no credit given

Check there are no foreign objects obstructing the

sensors (see Section 2 of this manual set).
Rear note detect
sensor obscured Check the back security flap moves freely (this is the
black plastic flap at the rear underside of the validator
head)

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 1 15

Check and clean the note path (see Section 2 of this

manual set).
Foreign objects in
note path
Check drive belts are fitted correctly and that there is no
debris underneath the belts.

Check voltage and current supplied to the validator are

within the tolerances specified in the Technical
Acceptor runs slowly Incorrect supply
Specification (see subsection 1.8 or Section 6 of this
or intermittently voltage
manual set).

If possible, replace damaged components (see Section 4

of this manual set).
Unit damage
IF YOU HAVE ANY DOUBTS, RETURN THE UNIT TO ITL
FOR REPAIR

Bezel LEDs are Check the flash code tables for an understanding of the
Various reasons
flashing issue (see subsection 1.9 of this manual).

Check and clean the note path (see Section 2 of this

manual set), then reset the validator.
Motor continues to Foreign object or
run note in the note path
In some cases you may also need to reset the host
machine.

If you are unsure about the cause or how to resolve the problem, please contact ITL’s
technical support department. Support contact details can be found on the ITL
website (www.innovative-technology.co.uk), or on the last page of this section.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 1 16

1.11 Frequently Asked Questions

a. Why are there no DIP switches on the unit?

 The NV11 has no dipswitches. Configuring the unit is carried out by using the
configuration button mounted on the front of the Note Float module – see
subsection 1.5 of this manual for more information.

b. In what orientation can I use the NV11 validator?

 The NV11 can only be mounted horizontally - see subsection 1.1 of this manual
for more information on mounting the validator. Check the ITL website to see
the currently available range of cashboxes and bezels.

c. How do I check which interface has been set?

 You can check which interface has been selected by using the configuration
button mounted on the front of the Note Float module – see subsection 1.3 of
this manual for more information.

d. How do I change the interface type?

 You can change the interface type by using the configuration button mounted
on the front of the Note Float module – see subsection 1.5 of this manual for
more information.

e. Some or all notes are not accepted

 Check that no inhibits are set in the Validator Manager software (see Section 3
of this manual set). If the problem persists, contact ITL Support for further
assistance.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set

MAIN HEADQUARTERS Innovative Technology Ltd

Derker Street – Oldham – England - OL1 4EQ
Tel: +44 161 626 9999 Fax: +44 161 620 2090
E-mail: [email protected]
Web site: www.innovative-technology.co.uk

BRAZIL
[email protected]

CHINA
[email protected]

GERMANY
[email protected]

SPAIN
[email protected]

UNITED KINGDOM
[email protected]

UNITED STATES OF AMERICA

[email protected]

REST OF THE WORLD

[email protected]

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 SECTION 2
NV11
MANUAL SET

FIELD SERVICE
MANUAL

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 2 2

NV11 MANUAL SET – SECTION 2

2. FIELD SERVICE MANUAL 3

2.1 Cleaning 3
2.2 Fault Finding - Flash Codes 10
2.3 Technical Specifications 12
2.4 Fault Finding Flow Chart 13
2.5 Frequently Asked Questions 15
2.6 Spare Parts 16

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 2 3

2. FIELD SERVICE MANUAL

This section is one part of a complete manual set: typically, a field service engineer
who is maintaining the product would use this section.

This section contains the essential information that the field engineer needs to clean,
maintain and fault find an NV11 validator that is installed in a host machine.

The NV11 validator has been designed to minimise any problems or performance
variations over time. This has been achieved by careful hardware and software
design; this attention to the design means there is very little user maintenance
required.

2.1 Cleaning

The NV11 validator has been designed in a way to prevent damage and airborne
contamination reaching the optical sensors; however, depending upon the
environment the NV11 may require occasional cleaning or belt changing.

Caution! Do not use solvent based cleaners such as

alcohol, petrol, methylated spirits, white spirit or
Do not use solvent based PCB cleaner. Using these solvents can cause
cleaners on any part of the permanent damage to the unit; only use a mild
NV11 unit. detergent solution as directed below.

To clean the NV11, open the note

path by sliding the red release catch
on the front of the validator to the
left (as indicated in the picture) - this
will allow access to the lozenge and
note path

Release
catch

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 2 4

Note path
Lozenge
release
catch

Lozenge

Drive belts

Note stacker

Cash box
spring plate

Note Float
module

Cashbox

Unless stated otherwise, you should disconnect

WARNING! the power BEFORE carrying out any cleaning
operations to avoid the risk of causing damage
Disconnect power BEFORE to the validator.
any cleaning operation

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 2 5

Ideally, you should also remove the Note Float module prior to cleaning the sensors.
Removal is a very straightforward task:

WARNING! Do not attempt to disassemble the Note Float

module – there are no user serviceable parts
Do not try to disassemble inside and trying to disassemble the module
could cause personal injury and will also
damage the unit beyond repair.

1. Open both the Note

Float side latches as
shown

2. Carefully lift the Note

Float module upwards
and clear of the
validator head

3. To refit the Note Float

module, reverse the
procedure – make
sure that the electrical
connectors and
latches are lined up
correctly Electrical
connector

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 2 6

Front sensors

Optical sensor

Start sensor

Rear sensor

Optical sensor

Examine the note paths, lozenge and note stacker for any dirt or debris, and carefully
clear and wipe the surfaces of the note paths and lozenge with a soft lint free cloth
that has been dampened with a water and mild detergent solution (i.e. household
washing up liquid.) - be very careful when cleaning around the sensor lenses and
make sure they are clean and dry before closing the cover and restarting the unit. Do
not try to polish the sensor lenses – if a lens is badly scratched, contact ITL technical
support for advice.

Also check that the note stacker and cash box spring plate are not jammed.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 2 7

Caution! When cleaning the recessed front sensor, use a

small soft brush or cotton bud – do not use
Be careful cleaning sensors. anything sharp or abrasive.

Cleaning the belts is a simple operation. Ensure the validator is enabled (i.e. bezel
lights are illuminated), then remove the bezel:

b. Slide bezel away from

 The bezel is locking arms
removed by pushing
the red locking arms
on both sides of the
validator upwards,
and sliding the bezel
away from the
locking arms

a. Push locking arms upwards

Lift upwards to remove

 Lift the bezel off
once the bezel has
been slid fully
across and is clear
of the locating pins

Locating pins

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 2 8

 Insert a piece of
paper (which is
narrower than the
width between the
two belts) in the
centre of the note
path to activate
the drive motor

 Use a lint free

cloth dampened
with water and
containing a mild
detergent (such as
dish detergent)
and hold against
each drive belt as
is turns.

Insert paper here

Repeat this procedure until all dust and debris has been removed from both belts.
Finally, use a DRY lint free cloth to remove any excess moisture and refit the bezel.
The bezel is refitted by pushing the bezel back onto the locating pins and sliding
backwards until all six pins are engaged in the slots. The locking arms will then spring
back and locate into the bezel.

Caution! Always make sure that BOTH locking arms are

fully located in the bezel – trying to operate the
Check locking arms. validator if they are not correctly located can
cause unit damage.

Caution! Do not lubricate any of the note transport

mechanism, belts or any part of the note path,
Do not use any lubricants. as this can affect the operation of the validator.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 2 9

If the belts are worn or damaged, they should be replaced. This is a simple
procedure, and is carried out as follows:

WARNING! Do not attempt to disassemble the validator

head or Note Float module – trying to do this
Do not try to disassemble could cause personal injury and will damage the
unit beyond repair.

 Open the top of

the unit using the Release catch Lozenge
Release catch release
catch
 Release the
lozenge by gently
pressing the
Lozenge release
catch

 Remove and
Lozenge
place the lozenge
on a clean dry
surface

 Press in the large Drive belts

wheels to release
the belt tension
and then remove
the belts, sliding
them off the
smallest wheels
first

 Replace the belts

by fitting them
over the lozenge,
largest wheels
first

 Reassemble and
close the unit

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 2 10

2.2 Fault Finding - Flash Codes

The NV11 validator has inbuilt fault detection facilities. If there is a configuration or
other error either the Note Float module status LED, or the NV9USB validator head
front bezel will flash in a particular sequence; a summary of the Flash Codes for both
units is shown below:

NV9USB Bezel Flash Codes:

Flashes Indicated Error Comments

Long Short
0 0 None
Remove obstruction and
follow the cleaning
2 Note path obstructed
procedure in Section 2 of
1
this manual set
Contact ITL technical
3 Unit not initialised
support
Check that the cash box
note plate is free to move
2 2 Cash box problem
and the stacker mechanism
is in the home position
Firmware checksum
1
error
Interface checksum
error or unable to
2
set programmed
Download new firmware
interface
3 EEPROM checksum
3
error
Dataset checksum
4
error
Check the validator
Incompatible
5 firmware is compatible with
firmware
the Note Float module
Power supply too
1
low
4 Check power supply
Power supply too
2
high

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 2 11

Note Float Module Flash Codes:

Flashes Indicated Error Comments

0 None
Constant Remove trapped note from the
flash Note Float module and press
Note transport error
(1 every the configuration button once
second)
Download new dataset /
2 Software error
firmware
Return to service centre for
3 Calibration error
repair
Check for trapped notes
4 Diverter error stopping the diverter returning
to the home position
Check for trapped notes
5 Motor timeout stopping the Note Float module
tape from moving

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 2 12

2.3 Technical Specifications

The full technical specifications for the NV11 validator can be found in Section 6,
Appendix B of this manual set. A brief summary is given here:

DC Voltage Minimum Nominal Maximum

Absolute limits 10.8 V 12 V 13.2 V
Supply ripple voltage 0V 0V 0.25 V @ 100 Hz
Supply Current
Standby 350 mA
Running 3A
Peak (motor stall) 3.5 A

Interface Logic Levels Logic Low Logic High

Inputs 0 V to +0.5 V +3.7 V to +12 V
Outputs (2.2 kΩ pull-up) +0.6 V Pull-up voltage of host
interface
Maximum current sink 50 mA per output

WARNING! Ensure that the supply voltage to the NV11 is not

lower than 10.8 V and that the power supply can
Use suitable power supply
provide sufficient current to avoid incorrect
operation and excessive note rejects.

We recommend that your power supply is capable of supplying 12V DC at 4 A.

 For 12V operation, use TDK Lambda model SWS50-12. This power supply is
available from a variety of suppliers including Farnell (stock code 1184645) and
RS (stock code 466-5869).

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 2 13

2.4 Fault Finding Flow Chart

Please use this flow chart with the Flash Codes in subsection 2.2 as an aid to help
resolve any configuration or start up problems you might have after installing the
NV11 validator

Check the required dataset is programmed using the

Incorrect currency
Validator Manager Software (see Section 3 of this
file
manual set).

Check the required note denomination and issue is

Notes not included in
included in the currency file using the Validator Manager
currency file
Software (see Section 3 of this manual set).
All notes rejected
(bezel LEDs ON)
Check the host machine is ready to accept notes and
Notes inhibited by
that the maximum allowed credit hasn’t been exceeded.
host machine
If a coin hopper is fitted, make sure it isn’t empty.

Check there is sufficient clearance for note ejection after

Note path obstructed
acceptance (see Section 4 of this manual set).

Check there is power to the validator, and that it is

No power within the tolerances specified in the Technical
Specification (see subsection 2.3 of this manual).
Notes not accepted
(bezel LEDs OFF) Check which interface the validator is programmed for by
Incorrect interface pressing the configuration button twice – the displayed
programmed code indicates which interface is programmed (see
Section 1 of this manual set).

Check voltage and current supplied to the validator are

within the tolerances specified in the Technical
Power supply out of Specification (see subsection 2.3 of this manual).
specification
Check there is sufficient clearance for note ejection after
Notes accepted but acceptance (see Section 4 of this manual set).
no credit given

Rear note detect Check there are no foreign objects obstructing the
sensor obscured sensors (see subsection 2.1 of this manual).

Check the back security flap moves freely (this is the

black plastic flap at the rear underside of the validator
head)

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 2 14

Foreign objects in Check and clean the note path (see subsection 2.1 of
note path this manual).

Check voltage and current supplied to the validator are

Acceptor runs slowly Incorrect supply within the tolerances specified in the Technical
or intermittently voltage Specification (see subsection 2.3 of this manual).

If possible, replace damaged components (see Section 4

of this manual set).
Unit damage
IF YOU HAVE ANY DOUBTS, RETURN THE UNIT TO
ITL FOR REPAIR

Bezel LEDs are Check the flash code tables for an understanding of the
Various reasons
flashing issue (see Subsection 2.2 of this manual).

Check and clean the note path (see Subsection 2.1 of

this manual), then reset the validator.
Motor continues to Foreign object or
run note in the note path
In some cases you may also need to reset the host
machine.

If you are unsure about the cause or how to resolve the problem, please contact ITL’s
technical support department. Support contact details can be found on the ITL
website (www.innovative-technology.co.uk), or on the last page of this section.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 2 15

2.5 Frequently Asked Questions

a. Why are there no DIP switches on the unit?

 The NV11 has no dipswitches. Configuring the unit is carried out using a
configuration button mounted on the front of the Note Float module – see
Section 1, subsection 1.5 of this manual set for more information.

b. In what orientation can I use the NV11 validator?

 The NV11 can only be mounted horizontally - see Section 1, subsection 1.1 of
this manual for more information on mounting the validator. Please check the
ITL website to see the currently available range of cashboxes and bezels.

c. Some or all notes are not accepted

 Check that no inhibits are set in the Validator Manager software (see Section 3
of this manual set). If the problem persists, contact ITL Support for further
assistance.

d. How do I clean the validator?

 Follow the instructions given in subsection 2.1 of this manual.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 2 16

2.6 Spare Parts

Full details of the interface cable connector pinouts, connector types / makes and other related information can be found in Section 4
of this manual set. The user can obtain the following parts for the NV11 validator:

ITL Part Number Description Details

CN215 Ribbon interface cable Provides connection between DA2 and NV11

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 2 17

ITL Part Number Description Details

CN292 Interface cable Provides connection between DA2 and NV11

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 2 18

ITL Part Number Description Details

CN392 Power and USB Communication Cable USB 2.0 Compliant Type A to 16 way header cable

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 2 19

Bezels
ITL Part Description
Number

PA189 Horizontal Bezel Assembly

69mm Fixed Width No image available

PA268
Horizontal Bezel

PA896 Horizontal Bezel Assembly

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 2 20

Cashboxes

Locking Cashbox
PA186
Assembly (300L)

Slide-on Cashbox
PA192
Assembly (300S)

Standard Cashbox
PA898
Assembly

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 2 21

There are many variants of bezel and cashbox type

Information
available for the NV11 validator. Please check the ITL
Check website for options. website (www.innovative-technology.co.uk) for up to
date information on the options available.

Drive Belts

FD106 NV9USB Red Drive Belt

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set

MAIN HEADQUARTERS Innovative Technology Ltd

Derker Street – Oldham – England - OL1 4EQ
Tel: +44 161 626 9999 Fax: +44 161 620 2090
E-mail: [email protected]
Web site: www.innovative-technology.co.uk

BRAZIL
[email protected]

CHINA
[email protected]

GERMANY
[email protected]

SPAIN
[email protected]

UNITED KINGDOM
[email protected]

UNITED STATES OF AMERICA

[email protected]

REST OF THE WORLD

[email protected]

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 SECTION 3
NV11
MANUAL SET

ITL SOFTWARE
SUPPORT GUIDE

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 2

NV11 MANUAL SET – SECTION 3

3. ITL SOFTWARE SUPPORT GUIDE 3

3.1 PiPS Software 3
3.1.1 Preparing for Installation 3
3.1.2 BV Interface Drivers 7
3.1.3 Installing the Drivers 10
3.1.4 Installing the PiPS Software 18
3.1.5 Starting the PiPS Software 21
3.1.6 Preferences, Settings and Options 24
3.2 Updating Firmware and Datasets 29
3.3 Tools 34
3.3.1 Diagnostics 34
3.3.2 Connections 40
3.4 Frequently Asked Questions 42

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 3

3. ITL SOFTWARE SUPPORT GUIDE

3.1 PiPS Software

PiPS (Pay in Pay out System) is a software package developed by Innovative

Technology Ltd to allow customers to carry out programming, setup and operational
tasks on the full range of NV11 devices.

3.1.1 Preparing for Installation

If you do not have the PiPS software on CD, you can easily download it from the
Innovative Technology website. Visit www.innovative-technology.co.uk, and select
‘Software Download’ from the ‘Support’ tab:

Clicking this link will take you to the software download page. To download any files
you must log in as a registered user – if you have not already registered this is a very
quick process; just click the ‘create an account’ link and follow the on-screen
instructions.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 4

Enter your login

details here, or
create a new
account

After logging in, the download screen will change slightly:

Your user name will be displayed in

the top right hand corner of the
screen

The padlock icon for each file will

change from locked to unlocked. To
download a file, just click on the
padlock icon opposite the file name.
If you want to find more information
about the file before you download
it, you can click on the blue
information icon.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 5

In this case, we want to download the PiPS software, so we click on the padlock icon
opposite the ‘SMART PIPS (Pay In Pay Out System)’ filename:

After clicking the link, a file download dialog box will appear – choose the option to
save the file:

You can save the file anywhere that is convenient, as long as you can remember
where it is when you want to install the software.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 6

After choosing where to save the file, a file transfer dialog box will appear showing
the progress of the file download:

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 7

3.1.2 BV Interface Drivers

After downloading the Validator Manager software, you will also need to download the
Banknote Validator (BV) Interface drivers – two versions are available (32 bit and 64
bit) so choose the correct type for your operating system. Again, remember where
you saved the file.

Both files are provided in a ‘zipped’ (compressed) form – you will need to extract the
files from the zipped file before you can install the software or driver. Any version of
Windows from Windows 98 onwards can open zipped files; or you may want to use a
third party software tool such as Winzip or WinRAR.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 8

Extract the files to a convenient location – this might be an existing folder, or you may
want to save them into a new folder.

In this example, the BV Interface driver files are being saved into a folder called
‘Drivers’ on the computers C: drive.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 9

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 10

3.1.3 Installing the Drivers

There are several ways to communicate with the NV11 validator, which include using
a direct connection from computer to validator with a CN392 validator to USB cable, or
by using a special interface unit called a DA2. Use of the DA2 is not covered here –
please refer to ITL Document number GA338-2 for more information. In this manual
we will be using the USB connection method. The connector needed to set up and
interface the NV11 validator is easily accessible on the side of the unit:

Interface
Connector

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 11

To use a USB connection with the NV11, a USB cable fitted with a 16 way connector
on one end (ITL Part Number CN392) should be used. The CN392 cable fits into the
16 way connector and allows high speed programming and serial communications
when used in SSP and ccTalk modes. When using the USB connection, power must be
supplied to the NV11 using the red and black power leads on the CN392 cable.

The NV11 validator must be powered up for the interface to be recognised by

Windows. If the validator is not in the host machine, you will need to provide power
to the 16 way interface connector first. The connection information and pin numbering
is as follows:

Pin Description
1 Serial Data Out (Tx)
5 Serial Data In (Rx)
11 USB Data +
12 USB Data -
13 USB Power (+5V)
15 +V
16 0V / Ground Connection

Before connecting the USB cable to the computer, make sure that the CN392 cable is
connected to the validator and that the unit is powered up. Once you have carried out
these steps, plug the USB cable into the computer.

After connecting the USB cable, Windows

should then detect the NV11 validator
interface – a ‘Found New Hardware’
bubble or dialog box should appear.

A ‘Found New Hardware’ wizard should then start to guide you through the installation
process (this first screen is not always shown on some computers):

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 12

Select this option

as you already
have the drivers

Information
Please make sure that you are using the V2 drivers
Only use V2 drivers for the installation.

Select this option as

we have saved the
drivers to a known
location

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 13

The next dialog box will ask you where to search for the drivers:

Click the ‘Browse’

button to find the
driver files (in this
example C:\Drivers)

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 14

Uncheck this option

to speed up the
installation

Click the ‘Next’

button to install
the drivers

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 15

You may see a warning dialog saying that the drivers have not passed Windows logo
testing – you can ignore this warning. Just click the ‘Continue Anyway’ button.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 16

Click the ‘Finish’

button to complete
the installation

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 17

After completing the driver installation you can check that the communications port
has been installed correctly.

Open Windows Device Manager, and click on the Plus symbol (+) next to the ‘Ports’
entry. This will expand the list of installed communications ports. You should see an
entry for an ‘ITL BV Serial V2’ port as shown here:

The actual communications port number (in our example COM5) may vary depending
on your particular computer configuration.

Now the drivers have been correctly installed you can install the Validator Manager
software – this is covered next.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 18

3.1.4 Installing the PiPS Software

Installing the PiPS software is very straightforward. Find the PiPS installation file you
downloaded earlier, extract the installation file from the zipped file and double click
the file (it has an .msi extension) – this will start the installation process:

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 19

You can choose where you would like to install the software, or just accept the default
location (as shown above). Clicking on the ‘Next’ button will then ask you to confirm
the installation:

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 20

Once the installation is complete, you will have a new program group called ‘ITL
Smart Tools’ in the Windows Start Menu, similar to the one shown here:

You can run the PiPS software by clicking the ‘Pay-in Pay-Out system’ menu entry;
however, before you can use the PiPS software with an NV11 you will need to make
sure that you have installed the BV interface drivers (as described earlier).

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 21

3.1.5 Starting the PiPS Software

The PiPS software is launched by clicking the ‘Pay-in Pay-out system’ entry in the ‘ITL
Smart Tools’ menu group.

The initial program screen looks like this:

Make sure that the NV11 is powered up and the USB cable is connected before going
any further.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 22

Once the NV11 is connected, there are two ways to start the program operation:

Click the ‘Start-up’ icon Click ‘Utilities’, then ‘Run PIPS System’

The PiPS software will then start to connect to the NV11.

Depending on the number and types of communications
ports on your computer, you may get an error message
similar to the one shown on the right saying ‘Unable to
open this port’ – this isn’t a problem, just click the ‘OK’
button.

You will see some text in the PiPS program

window as the software checks the
communications ports for the NV11 (similar
to what is shown here) – this text may vary
depending on your particular computer
configuration.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 23

Once the NV11 unit has been found, two windows will appear on the screen:

This window shows the

installed currency, level
and programming
information for the
connected NV11.

This window will

display all the
communications
events

More details of the program options and operations that can be carried out will be
covered in the next subsection.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 24

3.1.6 Preferences, Settings and Options

The preferences for the PiPS software are

accessible from the Utilities menu (as
shown). Click the ‘Options’ entry to open
a new dialog box:

This option sets the protocol version

used for communications – contact ITL
Technical Support for the current
configuration details.
This option allows the
user to display bank
note by value or channel

Check this option to allow detailed

protocol logging

This option is not

applicable for the NV11

Normally, these preferences should not need changing.

The settings and options for the NV11 vary depending whether the system is in the
'Run' or the 'Halt' state – generally the system will need to be halted before any
changes to setup options can be made. Pay in/pay out operations are only available
when in ‘Run’ state.

Halt State

If the system is in ‘Halt’ state, the user will either

have just started the PiPS software, or clicked on
the ‘Halt’ button. The menu bar will look like this:

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 25

The main screen should look something like this:

The various settings and options can be accessed from a right click when the mouse
cursor is over any of the system device entries:

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 26

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 27

Halt State Options

Set Route To set the pay in route for inserted bank notes to either
Cashbox or Note Float module, select the desired
denomination(s) and click the required route. The system will
send the commands to the device and store these preferences
so that they will be set again on the next start-up.

Set Options Using this dialog, the user can setup the device SSP address
and eSSP keys by double clicking on the required option.

Get Error Status This option displays any device error messages in the ‘System
Events’ window.

Download Update This option allows the user to download an ITL update file to
File the connected device.

Send SSP This option brings up the SSP communications dialog which
Command allows the user to send individual commands to the connected
device.

Exercise care when changing the device eSSP key.

CAUTION! The user must make a note of the new key and
change the host key to match. If the key is not
Take care when changing
known then device must be returned to ITL for key
eSSP key
reset.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 28

Run State

If the system is in ‘Run’ state, the user will have clicked on the ‘Run’ button and the
menu bar will look like this:

Run State Options

Set Route To set the pay in route for inserted bank notes to either
Cashbox or Note Float module, select the desired domination(s)
and click the required route. The system will send the
commands to the device and store these preferences so that
they will be set again on the next start-up.

Empty This command will empty all the stored notes in the connected
Note Float module into the device cashbox. After emptying the
notes, counters on the device will be reset to zero.

Reset This command will reset the connected payout device. After
reset, the system will re-initialise the device for use.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 29

3.2 Updating Firmware and Datasets

CAUTION! Powering off the NV11 when updating the

firmware or dataset can cause the validator to stop
Do not power off working.

The NV11 validator firmware and dataset can be updated very easily using the PiPS
software. The process uses NV9USB dataset files which can be downloaded from the
Innovative Technology Ltd website:

The firmware and dataset files for the NV11 validator

Information
are combined into a single file, so both will be
Combined data files updated when you carry out the update.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 30

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 31

After selecting the dataset, a dialog will prompt you to save or open the file: select
the Save option

You can then choose where to save the file – choose a location that is convenient for
you:

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 32

Once the dataset file is saved, unzip the file and you can then start the process to
update the NV11 validator by connecting the USB cable and starting the PiPS software
as described previously.

With the PiPS software in

‘Halt’ mode, right click on one
of the currency entries and
select ‘Download Update File’
from the dialog as shown
here:

You will then be prompted to select the dataset file you downloaded and unzipped
earlier – select the file and click the ‘Open’ button:

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 33

The PiPS software will then ask you to confirm that this is file you want to use to
update the NV11 unit with – click the ‘Yes’ button to continue:

A new dialog will then appear showing the update status:

After the reset is complete, the NV11 validator will then be ready for use with the new
currency.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 34

3.3 Tools

3.3.1 Diagnostics

There is a dedicated software diagnostics tool for use with the NV11 validator called
‘Bank Note Validator Diagnostics Tools’, and this software can be downloaded from
the Innovative Technology Ltd website:

When the file download dialog box appears, click the ‘Save’ button and select a
suitable location to save the file in:

Installing the Diagnostics tools software is done in the same way as the PiPS software
- Find the ITLDiagnosticsTools zipped file you just downloaded, extract the installation
file from the zipped file and double click the extracted file (it has an .msi extension) –
this will start the installation process.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 35

After installing the software, you can run the

diagnostics software by selecting the
‘Shortcut to ITL Diagnostics.exe’ item near
the top of the Windows Start menu. Make
sure that the NV11 Validator is powered up
and the USB cable is connected before
starting the program.

The main screen of the diagnostics tools software looks like this:

When running the software for the first time, you need to set a few options. These
are accessed from the ‘Options’ menu:

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 36

By selecting the ‘Serial Port’ item

from the ‘Options’ menu you can
define which serial port is being
used to connect to the NV11
validator. After selecting this
option, a new dialog box will open
allowing you to choose the correct
serial port.

Select the required port from the dropdown list,

and then click the ‘OK’ button to confirm your
selection. This will close the dialog box and allow
you to select another option from the menu. You
shouldn’t normally need to change the language
setting, as this is determined by the Windows
locale settings. You can if you wish select one of
four specific languages if needed, as shown
below:

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 37

Select the ‘Diagnostics’ item from

the ‘Utilities’ menu to start the
diagnostics process (you can also
start the diagnostics by clicking
on the left hand icon below the
menu bar) - this will open the
Diagnostics screen:

Click the ‘Start Diagnostic’ button to start the diagnostic process. The software will
then prompt you to insert a special piece of green diagnostics paper (ITL part number
LB149). Insert the paper in the same way you would with a bank note – at the end of
the diagnostics test the paper will be ejected.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 38

Diagnostics Pass:

A summary of the validator type and Motor test results are shown in
related information is displayed here. this window.

The overall test result is displayed here.

Sensor test results are shown in

this window.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 39

Diagnostics Fail:

Motor test results are shown in

A summary of the validator type and this window – in this example all
related information is displayed here. the motors have passed testing.

The overall test result is displayed here.

Sensor test results are shown in this

window – in this example, several sensors
have failed during the diagnostics test.

Further details on how to use the diagnostics tools and interpret the results can be
found in the program help file.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 40

3.3.2 Connections

The NV11 validator has a single connector that is used to allow interfacing and
programming.

Information
Power is always required on pins 15 and 16 of the
Power always required 16 way connector.
regardless of connection
type.

The connector is a 16 pin socket used to interface the NV11 to the host machine. The
pin numbering of the socket is shown below, as well as an overview of the socket
connections:

Pin Description
1 Serial Data Out (Tx)
5 Serial Data In (Rx)
11 USB Data +
12 USB Data -
13 USB Power (+5V)
15 +V
16 0V / Ground Connection

To use a USB connection with the NV11, a USB cable fitted with a 16 way connector
on one end (ITL Part Number CN392) should be used. The CN392 cable fits into the
16 way connector and allows high speed programming and serial communications
when used in SSP and ccTalk modes. When using the USB connection, power must be
supplied to the NV11 using the red and black power leads on the CN392 cable.

The socket connections for the natively supported protocols are shown in the tables
below, as is a summary of the interface units needed for other types of operation:

WARNING! Do not make any connections to the interface socket

Risk of unit damage pins marked ‘Do not connect’ – making connections
to these pins could cause severe damage to the unit.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 41

NV11 SSP Interface:

Pin Name Type Description

1 TxD Output Serial data out (Tx)
2
3 Factory use only Do not connect
4
5 RxD Input Serial data in (Rx)
6
7
8 Factory use only Do not connect
9
10
11 USB D+ Data USB Data +
12 USB D- Data USB Data -
13 USB Vcc Power USB +V (+5V)
14 Factory use only Do not connect
15 V In Power +V
16 GND Ground GND

NV11 ccTalk Interface:

Pin Name Type Description

ccTalk data – must also be
1 TxD Output
connected to pin 5
2
3 Factory use only Do not connect
4
ccTalk data – must also be
5 RxD Input
connected to pin 1
6
7
8 Factory use only Do not connect
9
10
11 USB D+ Data USB Data +
12 USB D- Data USB Data -
13 USB Vcc Power USB +V (+5V)
14 Factory use only Do not connect
15 V In Power +V
16 GND Ground GND

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 3 42

3.4 Frequently Asked Questions

a. Why are there no DIP switches on the unit?

 The NV11 has no dipswitches. Configuring the unit is carried out using a
configuration button mounted on the front of the Note Float module – see
Section 1, subsection 1.5 of this manual set for more information.

b. Are 64 bit drivers available?

 Both 32 and 64 bit drivers can be downloaded from the ‘Support’ section of the
ITL website – please make sure that you are using the correct type of driver for
your Operating System.

c. Some or all notes are not accepted

 Check that no inhibits are set in the PiPS software. If the problem persists,
contact ITL Support for further assistance.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set

MAIN HEADQUARTERS Innovative Technology Ltd

Derker Street – Oldham – England - OL1 4EQ
Tel: +44 161 626 9999 Fax: +44 161 620 2090
E-mail: [email protected]
Web site: www.innovative-technology.co.uk

BRAZIL
[email protected]

CHINA
[email protected]

GERMANY
[email protected]

SPAIN
[email protected]

UNITED KINGDOM
[email protected]

UNITED STATES OF AMERICA

[email protected]

REST OF THE WORLD

[email protected]

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 SECTION 4
NV11
MANUAL SET

MECHANICAL
AND ELECTRICAL
MANUAL

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 2

NV11 MANUAL SET – SECTION 4

4. MECHANICAL AND ELECTRICAL MANUAL 3

4.1 Introduction 3
4.2 Assembly and Fitting Instructions 5
4.3 Bezel Removal and Refitting 8
4.4 Technical Specifications 9
4.5 Cable Specifications 10
4.6 Electrical Interfaces 11
4.7 Configuration Button 14
4.8 Programming 15
4.9 Basic Operation 16
4.10 Spare Parts 18
4.11 Guidance Notes 27
Cleaning 27
Manual Note Removal 35
Re-Initialisation 38
4.12 Drawings and Schematics 39

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 3

4. MECHANICAL AND ELECTRICAL MANUAL

This section is one part of a complete manual set: Design Engineers who are
designing a host machine cabinet, or looking to integrate the NV11 validator into an
existing cabinet would need to read this section. This section contains the all the
mechanical and electrical information a designer needs to effectively integrate the
NV11 validator into a host machine.

4.1 Introduction

The NV11 validator is made up of four basic components: an NV9USB validator head,
Note Float module, removable bezel and a cashbox (as shown below):

Note Float
module

Removable
bezel

NV9USB
validator
head

Cashbox

The NV11 is a device that can accept, validate and store 300 or 600 bank notes of
mixed denominations, and also has the capability of storing a further 30 notes in the
Note Float module for future payout.

Up to 16 different denominations of bank note can be accepted and stacked, and the
Note Float module can be programmed to store and dispense 30 single denomination
notes.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 4

The NV11 is a LIFO (Last In First Out) system. This means that only the last note in
the Note Float module is available to be paid out or moved to the stacker. Any value
note can be routed into the Note Float module using the ‘Set Routing’ command. It is
recommended that only one denomination of the chosen currency is stored in the
Note Float module.

NV11 NV11 NV11

Rear View Side View Front View

The NV11 validator is pin for pin compatible with

Information
the NV7 / NV8 / NV9 / NV10 series of validators,
Validator compatibility. but NOT with earlier versions of the product
(NV2 – NV5).

The NV11 validator leaves the factory preset to at least one currency and dataset so
that it is ready for immediate installation. The NV11 validator works with any NV9USB
currency dataset created by Innovative Technology Ltd - datasets can be downloaded
from the Support section of the ITL website.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 5

4.2 Assembly and Fitting Instructions

Installing the NV11 is a simple operation, but note that the validator can only be
installed horizontally:

The NV11 validator is pin for pin compatible with

Information
the NV7 / NV8 / NV9 / NV10 series of validators,
Validator compatibility. but NOT with earlier versions of the product
(NV2 – NV5).

1. If the validator head

Blanking plate
has a blanking plate
fitted, you will need
to remove this
BEFORE attempting to
fit the Note Float
module. If the Note
Float module is
already fitted, please
Validator head
go to step 6
2. Open the validator
head by sliding the
red release catch on
the front of the
validator to the left
(as indicated in the
picture)

Release catch

Caution! Always make sure the validator head has been

opened BEFORE trying to remove the blanking
Validator head MUST be plate – trying to remove the blanking plate with
opened. the validator head closed will cause unit
damage.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 6

Side clips
3. Remove the blanking
plate by disengaging
the two side clips and
lifting the blanking
plate upwards

4. Close the validator

head and then
carefully fit the Note Rear cover
Float module onto the
validator head,
making sure the rear
cover is securely
closed and the latches
are lined up correctly

Latch

5. Make sure both

latches are engaged
and closed

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 7

6. The validator can be

fitted with a standard
or slide-on cashbox of
300 or 600 note
capacity

7. If not already
attached, the
validator can be fitted
with a horizontal
bezel of your choice.

8. The cashbox is
Note Float module
attached to the
validator by locating
and sliding until the
cashbox is clipped Bezel
securely and secured
in the host machine
using the studs on the
bottom of the
cashbox
Validator
head

Mounting
Cashbox studs

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 8

There are many variants of bezel and cashbox type

Information
available for the NV11 validator. Please check the ITL
Check website for options. website (www.innovative-technology.co.uk) for up to
date information on the options available.

4.3 Bezel Removal and Refitting

b. Slide bezel away from

 The bezel is locking arms
removed by pushing
the red locking arms
on both sides of the
validator upwards,
and sliding the bezel
away from the
locking arms

a. Push locking arms upwards

Lift upwards to remove

 Lift the bezel off
once the bezel has
been slid fully
across and is clear
of the locating pins

Locating pins

The bezel is refitted by pushing the bezel back onto the locating pins and sliding
backwards until all six pins are engaged in the slots. The locking arms will then spring
back and locate into the bezel.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 9

Caution! Always make sure that BOTH locking arms are

fully located in the bezel – trying to operate the
Check locking arms. validator if they are not correctly located can
cause unit damage.

The technical drawings which can be found at the end of this section show all the
dimensional information needed to mount the unit.

4.4 Technical Specifications

The full technical specifications for the NV11 validator can be found in Section 6,
Appendix B of this manual set. A brief summary is given here:

DC Voltage Minimum Nominal Maximum

Absolute limits 10.8 V 12 V 13.2 V
Supply ripple voltage 0V 0V 0.25 V @ 100 Hz
Supply Current
Standby 350 mA
Running 3A
Peak (motor stall) 3.5 A

Interface Logic Levels Logic Low Logic High

Inputs 0 V to +0.5 V +3.7 V to +12 V
Outputs (2.2 kΩ pull-up) +0.6 V Pull-up voltage of host
interface
Maximum current sink 50 mA per output

WARNING! Ensure that the supply voltage to the NV11 is not

lower than 10.8 V and that the power supply can
Use suitable power supply
provide sufficient current to avoid incorrect
operation and excessive note rejects.

We recommend that your power supply is capable of supplying 12V DC at 4 A.

 For 12V operation, use TDK Lambda model SWS50-12. This power supply is
available from a variety of suppliers including Farnell (stock code 1184645) and
RS (stock code 466-5869).

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 10

4.5 Cable Specifications

The minimum specification for wire used in power cables for the NV11 validator is
given here:

Minimum Nominal Peak current Cable rating Insulation

AWG current rating rating rating
26 3.0 A 3.5 A 4A 80 °C

Do not use wire of an inferior specification, as this can cause operating problems with
the validator.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 11

4.6 Electrical Interfaces

Interface
Connector

The connector needed to set up and interface the NV11 validator is easily accessible
on the side of the unit:

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 12

Information
Power is always required on pins 15 and 16 of the
Power always required 16 way connector.
regardless of connection
type.

The connector is a 16 pin socket used to interface the NV11 to the host machine. The
pin numbering of the socket is shown below, as well as an overview of the socket
connections:

Pin Description
1 Serial Data Out (Tx)
5 Serial Data In (Rx)
11 USB Data +
12 USB Data -
13 USB Power (+5V)
15 +V
16 0V / Ground Connection

To use a USB connection with the NV11, a USB cable fitted with a 16 way connector
on one end (ITL Part Number CN392) should be used. The CN392 cable fits into the
16 way connector and allows high speed programming and serial communications
when used in SSP and ccTalk modes.

When using the USB connection, power must be supplied to the NV11 using the
CN392 cable. The socket connections for the natively supported protocols are shown
in the tables below:

WARNING! Do not make any connections to the interface socket

Risk of unit damage pins marked ‘Do not connect’ – making connections
to these pins could cause severe damage to the unit.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 13

NV11 SSP Interface:

Pin Name Type Description

1 TxD Output Serial data out (Tx)
2
3 Factory use only Do not connect
4
5 RxD Input Serial data in (Rx)
6
7
8 Factory use only Do not connect
9
10
11 USB D+ Data USB Data +
12 USB D- Data USB Data -
13 USB Vcc Power USB +V (+5V)
14 Factory use only Do not connect
15 V In Power +V
16 GND Ground GND

NV11 ccTalk Interface:

Pin Name Type Description

ccTalk data – must also be
1 TxD Output
connected to pin 5
2
3 Factory use only Do not connect
4
ccTalk data – must also be
5 RxD Input
connected to pin 1
6
7
8 Factory use only Do not connect
9
10
11 USB D+ Data USB Data +
12 USB D- Data USB Data -
13 USB Vcc Power USB +V (+5V)
14 Factory use only Do not connect
15 V In Power +V
16 GND Ground GND

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 14

4.7 Configuration Button

The NV11 does not use DIP switches to configure the unit – configuration and setting
is carried out by using a Configuration Button mounted on the front of the Note Float
module:

Note Float module

Configuration Button

Status LED

There are several functions available when using the Configuration Button, and these
are listed in this table:

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 15

Action Power Status Function

Press and hold (more than Powered ON Sets validator to Programming
2 seconds) until the bezel mode (SSP)
illuminates, then release
Press twice (within half a Powered ON Shows current interface type (see
second) flash count table below)
Press once when Note Powered ON Acknowledges that a note
Float module status LED is blockage has been cleared
flashing (transport error)

Flash Count Interface The NV11 validator leaves the factory preset
1 SSP to at least one currency and one firmware
6 ccTalk interface so that it is ready for immediate
6,1 ccTalk plain (16 bit) installation.
6,1,2 ccTalk (8 bit)

WARNING! When in programming mode, do not turn off the

Risk of unit damage power before the operation is complete as this will
make the unit unusable.

4.8 Programming

Full details on programming the NV11 validator using software can be found in
Section 3 of this manual set (ITL Software Support Guide).

It is not possible to program the NV11 by the use of a configuration card as this
method of programming is not yet implemented.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 16

4.9 Basic Operation

The NV11 validator is a device that can accept, validate and store 300 or 600 bank
notes of mixed denominations, and works with any NV9USB currency dataset created
by Innovative Technology Ltd.

Validated bank notes are stored in the NV11’s cashbox, and bank notes accepted by
the validator are not visible once inside the unit and can only be taken out of the
cashbox manually.

The NV11 validator has inbuilt fault detection facilities. If there is a configuration or
other error either the Note Float module status LED, or the NV9USB validator head
front bezel will flash in a particular sequence; a summary of the Flash Codes for both
units is shown below:

NV9USB Bezel Flash Codes:

Flashes Indicated Error Comments

Long Short
0 0 None
Remove obstruction and
follow the cleaning
2 Note path obstructed
procedure in Section 2 of
1
this manual set
Contact ITL technical
3 Unit not initialised
support
Check that the cash box
note plate is free to move
2 2 Cash box problem
and the stacker mechanism
is in the home position
Firmware checksum
1
error
Interface checksum
error or unable to
2
set programmed
Download new firmware
interface
3 EEPROM checksum
3
error
Dataset checksum
4
error
Check the validator
Incompatible
5 firmware is compatible with
firmware
the Note Float module
Power supply too
1
low
4 Check power supply
Power supply too
2
high

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 17

Note Float Module Flash Codes:

Flashes Indicated Error Comments

0 None
Constant Remove trapped note from the
flash Note Float module and press
Note transport error
(1 every the configuration button once
second)
Download new dataset /
2 Software error
firmware
Return to service centre for
3 Calibration error
repair
Check for trapped notes
4 Diverter error stopping the diverter returning
to the home position
Check for trapped notes
5 Motor timeout stopping the Note Float module
tape from moving

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 18

4.10 Spare Parts

ITL Part Number Description Details

CN215 Ribbon interface cable Provides connection between DA2 and NV11

Comments:
Please consult the tables on the next page for pin out and connector information.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 19

CN215 Parts List

Qty Description Supplier Alternative

2 8 way 2 row 2.54mm pitch friction lock housing Leotronics 2652-2161 Molex 90142-0016
8 Tin plated crimp socket 22-24 AWG Leotronics 2653-2000 Molex 90119-0110
2 Black heat shrink sleeving --- ---
1 22 AWG stranded 4 core cable, PVC insulated --- ---

CN215 Connectivity

CON1 CON2 Gauge Colour Comments

Pin
1 1 24 AWG Orange
5 5 24 AWG Brown
15 15 24 AWG Red V IN
16 16 24 AWG Black GND

Notes:
Pins 3, 4, 7, 8, 9, 10, 13 and 14 have no crimps fitted
Pins 2, 6, 11 and 12 have crimps fitted but these are not connected.

WARNING! If you choose to make your own cables, you must make sure that the wire gauges are suitable for use
Use correct wire with the validator. The minimum wire gauge for the CN292 cable is 24 AWG, with 22 AWG being
gauges recommended.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 20

ITL Part Number Description Details

CN292 Interface cable Provides connection between DA2 and NV11

Comments:
Please consult the tables on the next page for pin out and connector information.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 21

CN292 Parts List

Qty Description Supplier Alternative

2 8 way 2 row 2.54mm pitch friction lock housing Leotronics 2652-2161 Molex 90142-0016
8 Tin plated crimp socket 22-24 AWG Leotronics 2653-2000 Molex 90119-0110
2 Black heat shrink sleeving --- ---
1 22 AWG stranded 4 core cable, PVC insulated --- ---

CN292 Connectivity

CON1 CON2 Gauge Colour Comments

Pin
1 1 24 AWG Orange
5 5 24 AWG Brown
15 15 24 AWG Red V IN
16 16 24 AWG Black GND

Notes:
Pins 3, 4, 7, 8, 9, 10, 13 and 14 have no crimps fitted
Pins 2, 6, 11 and 12 have crimps fitted but these are not connected.

WARNING! If you choose to make your own cables, you must make sure that the wire gauges are suitable for use
Use correct wire with the validator. The minimum wire gauge for the CN292 cable is 24 AWG, with 22 AWG being
gauges recommended.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 22

ITL Part Number Description Details

CN392 Power and USB Communication Cable USB 2.0 Compliant Type A to 16 way header cable

Comments:
Please consult the tables on the next page for pin out and connector information.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 23

CN392 Parts List

Qty Description Supplier Alternative

1 USB 2.0 lead with type A plug Molex 88728-3400 RS 324-8362
2 8 way 2 row 2.54mm pitch friction lock housing Molex 90142-0016 Leotronics 2652-2161
9 Gold plated crimp socket 22-24 AWG Molex 90119-2110 Leotronics 2653-2000
2 Black heat shrink sleeving --- ---
2 26 AWG stranded single core cable, PVC insulated --- ---

CN392 Connectivity

CON1 CON2 Gauge Colour Comments

Pin
1 13 Red USB +V (+5V)
2 12 White USB Data – (twist together with Data +)
3 11 Green USB Data + (twist together with Data -)
4 16 Black USB GND - see figure 1 for connection detail
Screen 16 Black See figure 1 for connection detail
--- 16 26 AWG Black 0V - see figure 1 for connection detail
--- 15 26 AWG Red +12V - see figure 1 for connection detail
Notes:
CON2 pins 1 - 4 have crimps fitted but these are not connected.
CON2 pins 5 -10 and 14 have no crimps fitted

WARNING! If you choose to make your own cables, you must make sure that the wire gauges are suitable for use
Use correct wire with the validator. The minimum wire gauge for the CN392 cable is 26 AWG, with 24 AWG being
gauges recommended.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 24

Bezels
ITL Part Description
Number

PA189 Horizontal Bezel Assembly

69mm Fixed Width No image available

PA268
Horizontal Bezel

PA896 Horizontal Bezel Assembly

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 25

Cashboxes

Locking Cashbox
PA186
Assembly (300L)

Slide-on Cashbox
PA192
Assembly (300S)

Standard Cashbox
PA898
Assembly

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 26

There are many variants of bezel and cashbox type

Information
available for the NV11 validator. Please check the ITL
Check website for options. website (www.innovative-technology.co.uk) for up to
date information on the options available.

Drive Belts

FD106 NV9USB Red Drive Belt

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 27

4.11 Guidance Notes

Cleaning

The NV11 validator has been designed in a way to prevent damage and airborne
contamination reaching the optical sensors; however, depending upon the
environment the NV11 may require occasional cleaning or belt changing.

Caution! Do not use solvent based cleaners such as

alcohol, petrol, methylated spirits, white spirit or
Do not use solvent based PCB cleaner. Using these solvents can cause
cleaners on any part of the permanent damage to the unit; only use a mild
NV11 unit. detergent solution as directed below.

To clean the NV11, open the note

path by sliding the red release catch
on the front of the validator to the
left (as indicated in the picture) - this
will allow access to the lozenge and
note path

Release
catch

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 28

Note path
Lozenge
release
catch

Lozenge

Drive belts

Note stacker

Cash box
spring plate

Note Float
module

Cashbox

Unless stated otherwise, you should disconnect

WARNING! the power BEFORE carrying out any cleaning
operations to avoid the risk of causing damage
Disconnect power BEFORE to the validator.
any cleaning operation

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 29

Ideally, you should also remove the Note Float module prior to cleaning the sensors -
removal is a very straightforward task:

WARNING! Do not attempt to disassemble the Note Float

module – there are no user serviceable parts
Do not try to disassemble inside and trying to disassemble the module
could cause personal injury and will also
damage the unit beyond repair.

1. Open both the Note

Float side latches as
shown

2. Carefully lift the Note

Float module upwards
and clear of the
validator head

3. To refit the Note Float

module, reverse the
procedure – make sure
that the electrical
connectors and latches
are lined up correctly
Electrical
connector

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 30

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 31

Front sensors

Optical sensor

Start sensor

Rear sensor

Optical sensor

Examine the note paths, lozenge and note stacker for any dirt or debris, and carefully
clear and wipe the surfaces of the note paths and lozenge with a soft lint free cloth
that has been dampened with a water and mild detergent solution (i.e. household
washing up liquid.) - be very careful when cleaning around the sensor lenses and
make sure they are clean and dry before closing the cover and restarting the unit. Do
not try to polish the sensor lenses – if a lens is badly scratched, contact ITL technical
support for advice.

Also check that the note stacker and cash box spring plate are not jammed.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 32

Caution! When cleaning the recessed front sensor, use a

small soft brush or cotton bud – do not use
Be careful cleaning sensors. anything sharp or abrasive.

Cleaning the belts is a simple operation. Ensure the validator is enabled (i.e. bezel
lights are illuminated), then remove the bezel:

b. Slide bezel away from

 The bezel is locking arms
removed by pushing
the red locking arms
on both sides of the
validator upwards,
and sliding the bezel
away from the
locking arms

a. Push locking arms upwards

Lift upwards to remove

 Lift the bezel off
once the bezel has
been slid fully
across and is clear
of the locating pins

Locating pins

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 33

 Insert a piece of
paper (which is
narrower than the
width between the
two belts) in the
centre of the note
path to activate
the drive motor

 Use a lint free

cloth dampened
with water and
containing a mild
detergent (such as
dish detergent)
and hold against
each drive belt as
is turns.

Insert paper here

Repeat this procedure until all dust and debris has been removed from both belts.
Finally, use a DRY lint free cloth to remove any excess moisture and refit the bezel.
The bezel is refitted by pushing the bezel back onto the locating pins and sliding
backwards until all six pins are engaged in the slots. The locking arms will then spring
back and locate into the bezel.

Caution! Always make sure that BOTH locking arms are

fully located in the bezel – trying to operate the
Check locking arms. validator if they are not correctly located can
cause unit damage.

Caution! Do not lubricate any of the note transport

mechanism, belts or any part of the note path,
Do not use any lubricants. as this can affect the operation of the validator.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 34

If the belts are worn or damaged, they should be replaced. This is a simple
procedure, and is carried out as follows:

WARNING! Do not attempt to disassemble the validator

head or Note Float module – trying to do this
Do not try to disassemble could cause personal injury and will damage the
unit beyond repair.

 Open the top of

the unit using the Release catch Lozenge
Release catch release
catch
 Release the
lozenge by gently
pressing the
Lozenge release
catch

 Remove and Lozenge

place the lozenge
on a clean dry
surface

 Press in the large Drive belts

wheels to release
the belt tension
and then remove
the belts, sliding
them off the
smallest wheels
first

 Replace the belts

by fitting them
over the lozenge,
largest wheels
first

 Reassemble and
close the unit

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 35

Manual Note Removal

It is unlikely that you will need to manually remove notes from the Note Float module,
but there may be occasions where this needs to be done. Depending on the situation,
there are two methods that can be used.

Transport Error:

If the Note Float module status LED is flashing once every second, this indicates a
note transport error. To correct the problem, follow the following steps.

If you need to follow this procedure, the NV11

should be powered off and the Note Float module
Caution! removed from the validator. The rear cover of the
Risk of damage Note Float module is mechanically interlocked with
the validator head – if you try to force the cover
open the module and validator could be damaged
beyond repair.

1. Remove the Note Float module from the validator

head by opening the two side latches and lifting the
module upwards

2. Open the Note Float module rear cover by pressing

in the two red buttons, then lift the cover

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 36

3. Carefully remove the bank note, then close the

cover firmly and refit the module onto the validator
head

Press the Configuration Button once after powering

up the NV11 to decrease the note count by 1

Manual Emptying:

In the unlikely event that you need to remove all the bank notes from the Note Float
module, this can be done following the steps below (after removing the Note Float
module from the validator head as detailed previously). There is a special cross point
tool (ITL part number PM979) used to manually operate the module’s transport
mechanism – please do not use any other tool as you may damage the mechanism.

If you need to follow this procedure, only use the

Caution!
PM979 cross point tool and take great care not to
Risk of serious damage over wind the mechanism or force past the dead
to Note Float module stops – if you do the module will be damaged
internal mechanism beyond repair.

1. Remove the PM979 cross point tool

from the stowage location on the side
of the Note Float module by pulling
the tool away from the module

PM979 cross point tool

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 37

2. Open the Note Float module rear

cover by pressing in the two red
buttons, then lift the cover

3. Insert the cross head tool into the

top drive roller as shown here

4. Turn the roller with the cross point

tool ANTICLOCKWISE (as indicated
by the arrow) until all the bank notes
have been removed

After removing all the bank notes, close the rear cover firmly, place the cross point
tool back in the stowage position and refit the module onto the validator.

Do not attempt to disassemble the Note Float

WARNING! module or remove the side covers to try and remove
Do not attempt disassembly any notes inside, as the module will be damaged
beyond repair. Always follow the procedure given
above.

After removing bank notes manually, an ‘EMPTY’ command should be run when the
unit is powered back up.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 38

Re-Initialisation

The NV11 validator has an in-built self-calibration system that keeps the optical
sensors in optimum operating condition. However if the NV11 is disassembled for any
reason it also will need to be re-initialised - re-initialisation can only be carried out by
ITL’s technical support team.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 39

4.12 Drawings and Schematics

NOTE: If required, IGES 3D models are available on request from ITL technical support.

NV11:

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 40

Cashbox Options:

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 4 41

Standard Cashbox:

Assembly instructions:
1. Clip two springs (SP120) to the cash plate 4. Fit the cash box door (PA899) to the cash box
(MC161), then slide the assembly into the cash by pushing the door shaft flush to the door edge
box (MC310) making sure the cash plate is above at one end and inserting the extended part of
the cash box slot the shaft into the pivot hole in the cash box (see
View ‘B’)
2. Secure the springs to the cash box floor using 5. Twist the cash box door so the free end of
the 6 tabs in the base of the cash box the shaft slides into the other cash box pivot
hole (see View ‘B’)
3. Twist the cash plate and insert the end tab into 6. Push the cash box door closed (see View ‘C’)
the cash box slot (see View ‘A’), then push the
plate fully into the cash box (see View ‘C’)

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set

MAIN HEADQUARTERS Innovative Technology Ltd

Derker Street – Oldham – England - OL1 4EQ
Tel: +44 161 626 9999 Fax: +44 161 620 2090
E-mail: [email protected]
Web site: www.innovative-technology.co.uk

BRAZIL
[email protected]

CHINA
[email protected]

GERMANY
[email protected]

SPAIN
[email protected]

UNITED KINGDOM
[email protected]

UNITED STATES OF AMERICA

[email protected]

REST OF THE WORLD

[email protected]

Copyright © Innovative Technology Ltd 2012

Downloaded from www.Manualslib.com manuals search engine

 SECTION 5
NV11
MANUAL SET

SOFTWARE
IMPLEMENTATION
GUIDE

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 5 2

NV11 MANUAL SET – SECTION 5

5. SOFTWARE IMPLEMENTATION GUIDE 3

5.1 Communication Protocols 3
5.2 Configuration Card Programming 5
5.3 SSP and eSSP 5
5.4 ccTalk 16
5.5 SSP Escrow Function 20
5.6 Connection Options 21

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 5 3

5. SOFTWARE IMPLEMENTATION GUIDE

5.1 Communication Protocols

The NV11 validator can use two different communication protocols - SSP/eSSP and
ccTalk.

Smiley® Secure Protocol (SSP) is a secure serial interface specifically designed to

address the problems experienced by cash systems in gaming machines. Problems
such as acceptor swapping, reprogramming acceptors and line tapping are all
addressed.

Encrypted Smiley® Secure Protocol (eSSP) is an enhancement of SSP. eSSP uses the
same 16 bit CRC checksums on all packets as SSP, but also uses a Diffie-Hellman key
exchange to allow the host machine and validator to jointly establish a shared secret
key over an insecure communications channel. The encryption algorithm used is AES
with a 128-bit key; this provides a very high level of security.

The recommended communication protocol for the NV11 validator is eSSP, as this
provides the highest level of data transfer security. A ccTalk interface protocol is also
available.

For detailed information and the full protocol specifications please read the following
documents, which can be downloaded from the Innovative Technology Ltd website
(www.innovative-technology.co.uk):

 SSP Interface Specification (ITL Document number GA138)

 ccTalk Communications Protocol Specification [additional commands]
(ITL Document number GA964)
 ITL Bank Note Reader ccTalk Specification (ITL Document number GA966)

Summaries of the NV11 validator socket connections for the supported interfaces are
shown below:

WARNING! Do not make any connections to the interface socket

Risk of unit damage pins marked ‘Do not connect’ – making connections
to these pins could cause severe damage to the unit.

It is recommended that all transactions with the NV11

Information validator be encrypted to prevent commands being
recorded and replayed by an external device. If this is
Encryption of data strongly not possible, then other (mechanical) measures
recommended should be used to prevent physical bus tapping.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 5 4

NV11 SSP Interface:

Pin Name Type Description

1 TxD Output Serial data out (Tx)
2
3 Factory use only Do not connect
4
5 RxD Input Serial data in (Rx)
6
7
8 Factory use only Do not connect
9
10
11 USB D+ Data USB Data +
12 USB D- Data USB Data -
13 USB Vcc Power USB +V (+5V)
14 Factory use only Do not connect
15 V In Power +V
16 GND Ground GND

NV11 ccTalk Interface:

Pin Name Type Description

ccTalk data – must also be
1 TxD Output
connected to pin 5
2
3 Factory use only Do not connect
4
ccTalk data – must also be
5 RxD Input
connected to pin 1
6
7
8 Factory use only Do not connect
9
10
11 USB D+ Data USB Data +
12 USB D- Data USB Data -
13 USB Vcc Power USB +V (+5V)
14 Factory use only Do not connect
15 V In Power +V
16 GND Ground GND

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 5 5

5.2 Configuration Card Programming

It is not possible to program the NV11 by the use of a configuration card as this
method of programming is not yet implemented. Full details on programming the
NV11 validator using software can be found in Section 3 of this manual set (ITL
Software Support Guide).

5.3 SSP and eSSP

Smiley® Secure Protocol (SSP) is a secure serial interface specifically designed to

address the problems experienced by cash systems in gaming machines. Problems
such as acceptor swapping, reprogramming acceptors and line tapping are all
addressed.

Encrypted Smiley® Secure Protocol (eSSP) is an enhancement of SSP. eSSP uses the
same 16 bit CRC checksums on all packets as SSP, but also uses a Diffie-Hellman key
exchange to allow the host machine and validator to jointly establish a shared secret
key over an insecure communications channel. The encryption algorithm used is AES
with a 128-bit key; this provides a very high level of security.

The encryption of the SSP protocol ensures superior protection and reliability of the
data, which is transferred between validator and host machine. The encryption key is
divided into two parts:

 The lower 64 bits are fixed and specified by the machine manufacturer allowing
control of which devices are used in their machines.

 The higher 64 bits are securely negotiated by the slave and host at power up,
ensuring each machine and each session are using different keys.

The interface uses a master-slave model; the host machine is the master and the
peripherals (note acceptor, coin acceptor or coin hopper) are the slaves. Data transfer
is over a multi-drop bus using clock asynchronous serial transmission with simple
open collector drivers. Each SSP device of a particular type has a unique serial
number; this number is used to validate each device in the direction of credit transfer
before transactions can take place.

Information
When communicating with the NV11 validator, poll
200 ms command spacing commands should be sent at least 200 ms apart.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 5 6

SSP Commands and Responses

a. Commands

Action Command Code (Hex) Command Set

Reset 0x01

Host Protocol Version 0x06

Poll 0x07

Get Serial Number 0x0C

Synchronisation command 0x11 Generic

Disable 0x09

Enable 0x0A

Program Firmware / currency 0x0B (Programming Type)

Manufacturers Extension 0x30 (Command, Data)

Set inhibits 0x02

Display On 0x03

Display Off 0x04

Set-up Request 0x05

Reject 0x08

Unit data 0x0D Validator

Channel Value data 0x0E

Channel Security data 0x0F

Channel Re-teach data 0x10

Last Reject Code 0x17

Hold 0x18

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 5 7

Action Command Code (Hex) Command Set

Enable Protocol Version 0x19 (made obsolete in

Events protocol version 6)

Get Bar Code Reader 0x23

Configuration

Set Bar Code Reader 0x24

Validator
Configuration

Get Bar Code Inhibit 0x25

Set Bar Code Inhibit 0x26

Get Bar Code Data 0x27

Enable Payout Device * 0x5C, Options

Disable Payout Device 0x5B

Set Routing * 0x3B (route, value/channel

(Country code))

Get Routing * 0x3C (value/channel (Country

code))

Empty 0x3F
Note Float
Get Note Positions * 0x41

Payout Note 0x42

Stack Note 0x43

Set Value Reporting Type * 0x45 (type)

SMART empty 0x52

Cashbox Payout Operation 0x53

Data

The commands marked with * will respond with the generic response ‘Command
cannot be processed’ and an error code of ‘Invalid Currency’ if there are notes inside
the Note Float module that do not match the dataset that is installed in the validator.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 5 8

Notes:

Action Comments
Reset: Single byte command, causes the slave to reset
Host Protocol Version: Dual byte command, the first byte is the command; the
second byte is the version of the protocol that is
implemented on the host.
Poll: Single byte command, no action taken except to report
latest events.
Get Serial Number: Single byte command, used to request the slave serial
number. Returns 4-byte long integer.
Sync: Single byte command, which will reset the validator to
expect the next sequence ID to be 0.
Disable: Single byte command, the peripheral will switch to its
disabled state, it will not execute any more commands or
perform any actions until enabled, any poll commands
will report disabled.
Enable: Single byte command, the peripheral will return to
service.
Manufacturers This command allows the manufacturer of a peripheral to
Extension: send commands specific to their unit
Enable Payout Device: Two-byte command, the first byte is the command and
the second enables several different options. Unused bits
should be 0.
Disable Payout Device: Single-byte command. All accepted notes will be routed
to the stacker and payout commands will not be
accepted.
Set Routing: The first byte is the command. The second byte is the
selected route, and the remaining bytes are the four-
byte value or single byte channel number (depending on
the reporting type selected) of the note that the route
should be applied to. By default all note values are
stacked. For protocol version 6, three extra country code
bytes are sent
Empty: Single byte command, this will cause all notes to be sent
to the stacker for removal.
Get Note Positions: Single byte command, this will return the number of
notes in the Note Float module and the value in each
position. The first note in the table is the first note that
was paid into the Note Float module - the Note Float
module is a LIFO system, so the note that is last in the
table is the only one that is available to be paid out or
moved into the stacker.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 5 9

Action Comments
Payout Note: This is a single byte command. The Note Float module
will pay out the last note that was stored. This is the
note that is in the highest position in the table returned
by the Get Note Positions Command. If the payout is
possible the Note Float will reply with the generic
response ‘OK’.
Stack Note: This is a single byte command. The Note Float module
will stack the last note that was stored. This is the note
that is in the highest position in the table returned by the
Get Note Positions Command. If the stack operation is
possible the Note Float will reply with the generic
response ‘OK’.
Set Value Reporting Two-byte command. This will set the method of
Type: reporting values of notes. There are two options, by a
four-byte value of the note or by the channel number of
the value from the banknote validator. If the channel
number is used then the actual value must be
determined using the data from the Validator command
Unit Data. The default operation is by 4-byte value.
SMART empty: Empties the Note Float module of notes, maintaining a
count of value emptied. The note counters will be set to
0 after running this command. Use ‘cashbox payout
operation data’ command to retrieve a breakdown of the
denominations routed to the cashbox through this
operation.
Cashbox Payout This command can be sent at the end of a SMART
Operation Data: Empty, float or dispense operation. Returns the amount
emptied to cashbox from the Note Float in the last
dispense, float or empty command. The quantity of
denominations in the response is sent as a 2 byte little
endian array; the note values as 4-byte little endian
array and the country code as a 3-byte ASCII array. Each
denomination in the dataset will be reported, even if 0
notes of that denomination are emptied.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 5 10

b. Responses

Action Command Code (Hex) Command Set

OK 0xF0

Command not known 0xF2

Wrong number of parameters 0xF3

Parameter out of range 0xF4

Generic
Command cannot be 0xF5
processed

Software Error 0xF6

FAIL 0xF8

Key Not Set 0xFA

Slave Reset 0xF1

Read, n 0xEF, Channel Number

Credit, n 0xEE, Channel Number

Rejecting 0xED

Rejected 0xEC

Stacking 0xCC

Stacked 0xEB
Validator
Safe Jam 0xEA

Unsafe Jam 0xE9

Disabled 0xE8

Fraud Attempt, n 0xE6, Channel Number

Stacker Full 0xE7

Note cleared from front at 0xE1, Channel Number

reset

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 5 11

Action Command Code (Hex) Command Set

Note cleared into cash box at 0xE2, Channel Number

reset

Cash Box Removed 0xE3

Cash Box Replaced 0xE4

Validator
Bar Code Ticket Validated 0xE5

Bar Code Ticket Acknowledge 0xD1

Note Path Open 0xE0

Channel Disable 0xB5

Dispensing 0xDA, value/channel

dispensing

Dispensed 0xD2, value/channel

dispensed

Jammed 0xD5, value/channel

dispensing

Halted 0xD6

Incomplete Payout 0xDD, value/channel

dispensed, value/channel
requested

Note Float
Emptying 0xC2

Empty 0xC3

Note Stored in Payout * 0xDB, value/channel of note

Note Transferred to Stacker 0xC9, value/channel of note

Payout Out of Service 0xC6

Note Paid into Stacker at 0xCA, value/channel of note

Power Up

Note Paid into Store at Power 0xCB, value/channel of note

Up

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 5 12

Action Command Code (Hex) Command Set

Note Dispensed at Power Up 0xCD, value/channel of note

Note Float Removed 0xC7

Note Float Attached 0xC8

Note in Bezel Hold 0xCE, value/channel of note

Note Float
Device Full 0xCF

SMART Emptying 0xB3

SMART Emptied 0xB4

Channel Disable 0xB5

* When enabled using option flag.

Notes:

Action Comments
Command Not Known: Returned when an invalid command is received by a
peripheral.
Wrong Number Of A command was received by a peripheral, but an incorrect
Parameters: number of parameters were received.

Parameter Out Of One of the parameters sent with a command is out of

Range: range.

Command Cannot Be A command sent could not be processed at that time.

Processed:

Software Error: Reported for errors in the execution of software e.g.

Divide by zero. This may also be reported if there is a
problem resulting from a failed remote firmware upgrade,
in this case the firmware upgrade should be redone
Key Not Set: The slave is in encrypted communication mode but the
encryption keys have not been negotiated
Jammed: Five-byte response that indicates that the validator is
jammed; this is reported until it is un-jammed or reset. It
will also become disabled.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 5 13

Action Comments
Dispensing: Single-byte response indicating that a dispense operation
is in progress. The four-byte value of the note or the
single byte channel number is reported, depending on the
reporting type set. This value will be 0 until the note has
passed out of the Note Float module and into a payable
position in the validator.
Dispensed: Response that indicates when the payout has finished a
dispense operation; The four-byte value of the note or the
single byte channel number is reported, depending on the
reporting type set.
Jammed: Five byte response that indicates that the payout is
jammed; this is reported until it is un-jammed or reset. It
will also become disabled. The value or channel number of
the note being dispensed is also reported.
Incomplete Payout: This event is given when the payout starts up if a payout
or float operation was in progress when the power was
removed. The first four bytes after the event code are the
value that was dispensed; the next four are the value that
was originally requested.
Emptying: This event is given while the payout is being emptied of
notes into the cashbox by the EMPTY command.
Empty: This event is given at the end of the empty process.
Note Stored in This event is given when notes paid in to the payout
Payout: system are routed to the payout store. For compatibility
with the SMART Payout the value of the note is not
reported. However if the Note Float is enabled with the
option flag VALUE_ON_STORED set, then the value of the
note will be reported (see enable payout device
command).
Note Transferred to This event is given when a note has successfully been
Stacker: moved from the Note Float and stacked in the cash box.
During the process the Stacking event will be given.
Note Float Removed: This event is reported when the Note Float module is
physically disconnected from the validator while the power
is on.
Note Float Attached: This event is reported when the Note Float module is
physically attached to the validator while the power is on.
The validator and Note Float module will then reset.
Note In Bezel Hold: This event is reported when the Dispensing note is held in
the bezel waiting for the user to remove it.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 5 14

Action Comments
Device Full: This event is reported when the Note Float has reached its
limit of stored notes. This event will be reported until a
note is paid out or stacked.
Channel Disable: Indicates all note channels have been inhibited and as
such, the unit is disabled. Only reported if using protocol
version 7 and above.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 5 15

Example SSP Communications

Here is an example of the communication between host and slave. Both the typical
commands from the host and responses from the validator are detailed.

Host Slave Comments

> SYNC < OK Synchronisation command
> SET_GENERATOR, [64 bit < OK Set the encryption key
prime number] generator
> SET_MODULUS, [64 bit prime < OK Set the encryption key modulus
number]
> REQUEST_KEY_EXCHANGE < OK, [64bit slave Host sends the host
[64 bit host intermediate key] intermediate key] intermediate key, slave
responds with the slave
intermediate key. The
encryption key is then calculated
independently by both host and
slave.
> GET_SERIAL < OK < [SERIAL NV11 Serial Number
NUMBER]
> SETUP_REQUEST < OK < [SETUP NV11 Setup
INFORMATION]
> SET_ROUTING, 01 14 00 00 < OK Route notes of value 0020 to
00 the NV11 Cashbox
> SET_INHIBIT > 07 > 00 < OK Enable channels 1,2 and 3
> ENABLE < OK Enable NV11
> POLL < OK < DISABLED
> POLL < OK
> POLL < OK < NOTE READ NV11 currently reading a note
< 00
> POLL < OK < NOTE READ Note has been recognised as
< 03 channel 3 (€20)
> HOLD < OK Hold the note in escrow
> POLL < OK < STACKING Stack the note
> POLL < OK < CREDIT < Credit given for channel 3 (€20),
03 < STACKING < note stacked
STACKED
> POLL < OK

Full support is available from ITL and local support offices for implementing eSSP -
this support includes libraries and example applications. When requesting this
information, please specify your preferred language(s) and operating system.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 5 16

5.4 ccTalk

This section should be read in conjunction with the full ccTalk specification, which can
be downloaded from the internet (www.cctalk.org).

ccTalk is a serial communications protocol in widespread use throughout the money

transaction industry. Peripherals such as coin acceptors, note validators and hoppers
found in a diverse range of automatic payment equipment use ccTalk to communicate
with the host controller.

The protocol uses an asynchronous transfer of character frames in a similar manner to

RS232. The main difference is that it uses a single two-way communication data line
for half-duplex communication rather than separate transmit and receives lines. It
operates at TTL voltages and is ‘multi-drop’ (peripherals can be connected to a
common bus and are logically separated by a device address) - each peripheral on the
ccTalk bus must have a unique address.

Each communication sequence (a command or request for information) consists of 2

message packets structured in one of the formats detailed below. The first packet will
go from the master device to the slave device and then a reply will be sent from the
slave device to the master device.

Commands can have 3 primary formats:

 8 Bit Checksum – No Encryption

 16 Bit CRC – No Encryption
 16 Bit CRC – BNV Encryption

As it is possible to use the ccTalk protocol without encryption, suitable physical

security should be employed to protect the ccTalk bus.

Information When communicating with the NV11 validator, Read

Buffered Bill events (command 159) should be sent
200 ms command spacing at least 200 ms apart.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 5 17

ccTalk Command Summary

Command Header Parameters Example

Reset Device 001 None ACK
Request Comms 004 None X.Y
Revision
Force Empty NV11 019 SEL EVENT
Store to Cash Box
Request Expanded 020 SEL FLAG, EVENT,
NV11 status REMAIN, PAID,
UNPAID, STORED,
STORE, FLAG2
Clear Total Count 021 SEL ACK / NAK
Pump RNG 022 R1-R8 ACK
Request Cipher Key 023 None KEY1 – KEY8
Request Variable 024 SEL KEY, MC
Set
Modify Variable Set 025 SEL, KEY ACK
Request Total 026 SEL IN1-IN3, OUT1-
Count OUT3, STR1-STR3
Enable Payout 027 KEY ACK / NAK
Dispense NV11 028 SEL, SEC1-SEC8, EVENT / NAK
Notes BILL CNT
Request NV11 029 SEL FLAG, EVENT,
Status REMAIN, PAID,
UNPAID, STORED,
STORE
Emergency Stop 030 SEL, FUNC REMAIN
Empty NV11 Store 031 SEL EVENT
to Cash Box
Modify Variable MC 032 SEL, MC ACK / NAK
Set
Request RC Version 033 SEL VERSION
Request RC Count 034 SEL COUNT
Modify RC Count 035 SEL, COUNT ACK / NAK
Request Current 036 SEL COUNT
Count
Read Barcode Data 129 None ACK
Store Encryption 136 None ACK
Code
Switch Encryption 137 3 bytes Encryption ACK
Code key
Request Currency 145 None or Country ‘GBP02113’
Revision Code (2 digit)
Operate Bi- 146 None ACK
directional Motors
Stacker Cycle 147 None ACK
Request Bill 152 None 3
Operating Mode

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 5 18

Command Header Parameters Example

Modify Bill 153 Escrow & Stacker ACK
Operating Table
Route Bill 154 0/1 ACK/254
Request Bill Position 155 Country Code (2 00000111 00000000
digit)
Request Country 156 Country Code (2 100
Scaling digit)
Request Bill ID 157 None ‘GB0010A’
Read Buffered Bill 159 None 10000000000
Events
Request Address 169 None 1
Mode
Request Base Year 170 None 2006
Request Build Code 192 None 161209
Request Last Mod 195 None 00
Date
Calculate ROM 197 None 4 byte checksum
Checksum
Request Option 213 None 3 (stacker & escrow)
Flags
Request Data 216 None 00000
Storage Av.
Enter Pin 218 Pin1, Pin2, Pin3, ACK
Pin4
Enter New Pin 219 Pin1, Pin2, Pin3, ACK
Pin4
Request Accept 225 None 3
Count
Request Insertion 226 None 7
Count
Request Master 227 None 1
Inhibit
Set Master Inhibit 228 Bit Mask ACK
Request Inhibits 230 None Inhibit Low, Inhibit
High
Set Inhibits 231 Channels ACK
Perform Self Check 232 None 0
Request Software 241 None XX.YY
Version
Request Serial 242 None 3 byte serial number
Number
Request Product 244 None ‘NV11’
Code
Request Equipment 245 None ‘Bill Validator’
Category

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 5 19

Command Header Parameters Example

Request 246 None ‘ITL’
manufacturer ID
Request Polling 249 None 200
Priority
Simple Poll 254 None ACK

Monetary Values

Values are represented as 32 bit unsigned integers (4 bytes) and in the lowest value
of currency. For example:

€50.00 would be 0x00001388

When sending or receiving a value the least significant byte is sent first. So in this
example [0x88] [0x13] [0x00] [0x00] will be sent.

Each type of note is identified by its value and represented using the standard format
outlined above. As an example, the values for Euro notes are:

Note (€) Hex value Data to Send

5.00 0x000001F4 [0xF4] [0x01] [0x00] [0x00]
10.00 0x000003E8 [0xE8] [0x03] [0x00] [0x00]
20.00 0x000007D0 [0xD0] [0x07] [0x00] [0x00]
50.00 0x00001388 [0x88] [0x13] [0x00] [0x00]
100.00 0x00002710 [0x10] [0x27] [0x00] [0x00]
200.00 0x00004E20 [0x20] [0x4E] [0x00] [0x00]
500.00 0x0000C350 [0x50] [0xC3] [0x00] [0x00]

Communications Format

ccTalk communication is carried out using the following settings:

Baud rate= 9600bps, Data= 8 bit, No parity, Stop bit= 1bit

Command Format from Host to NV11

[Dst] [Len] [CRC (LSB)] [Header] [Data1] … [DataN] [CRC (MSB)]

Field Description
Dst Destination Address (for a note validator, 40 [0x28])
Len Number of data bytes in the message
Header Command
Data Data attached to Header, specified by Len (1-N)
CRC [Dst] + [Len] + [Header] + [Data1] + … + calculated value of CRC16
against Data N

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 5 20

Response Format from the NV11 to Host

ACK message:

[Dst] [00] [CRC (LSB)] [00] [CRC (MSB)]

NAK message:

[Dst] [00] [CRC (LSB)] [05] [CRC (MSB)]

BUSY message:

[Dst] [00] [CRC (LSB)] [06] [CRC (MSB)]

Response:

[Dst] [Len] [CRC (LSB)] [00] [Data1] … [DataN] [CRC (MSB)]

Field Description
Dst Destination Address (for a note validator, 40 [0x28])
Len Number of data bytes in the message
Header Reply message [00]
Data Data attached to Header, specified by Len (1-N)
CRC [Dst] + [Len] + [Header] + [Data1] + … + calculated value of CRC16
against Data N.

If encryption setting is enabled, encryption is carried out against:

[CRC (LSB)] + [Header] + [Data1] + … + [DataN] + [CRC (MSB)]

5.5 SSP Escrow Function

To hold a note in the escrow position when using SSP, the POLL command should be
replaced with the HOLD command after NOTE READ > 0 for as long as the note is to
be held in escrow.

A POLL command will then accept the note; the REJECT command will return the note
to the customer

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 5 21

5.6 Connection Options

The NV11 validator has a single connector that is used to allow interfacing and
programming:

Interface
Connector

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 5 22

Information
Power is always required on pins 15 and 16 of the
Power always required 16 way connector.
regardless of connection
type.

The connector is a 16 pin socket used to interface the NV11 to the host machine. The
pin numbering of the socket is shown below, as well as an overview of the socket
connections:

Pin Description
1 Serial Data Out (Tx)
5 Serial Data In (Rx)
11 USB Data +
12 USB Data -
13 USB Power (+5V)
15 +V
16 0V / Ground Connection

To use a USB connection with the NV11, a USB cable fitted with a 16 way connector
on one end (ITL Part Number CN392) should be used. The CN392 cable fits into the
16 way connector and allows high speed programming and serial communications
when used in SSP and ccTalk modes.

Further details of the cable needed to interface and program the NV11 validator can
be found in Section 4 of this manual set (subsection 4.9). When using the USB
connection, power must be supplied to the NV11 using the CN392 cable.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set

MAIN HEADQUARTERS Innovative Technology Ltd

Derker Street – Oldham – England - OL1 4EQ
Tel: +44 161 626 9999 Fax: +44 161 620 2090
E-mail: [email protected]
Web site: www.innovative-technology.co.uk

BRAZIL
[email protected]

CHINA
[email protected]

GERMANY
[email protected]

SPAIN
[email protected]

UNITED KINGDOM
[email protected]

UNITED STATES OF AMERICA

[email protected]

REST OF THE WORLD

[email protected]

Copyright © Innovative Technology Ltd 2012

Downloaded from www.Manualslib.com manuals search engine

 SECTION 6
NV11
MANUAL SET

TECHNICAL
APPENDICES

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 6 2

NV11 MANUAL SET – SECTION 6

6. TECHNICAL APPENDICES 3
APPENDIX A – PRODUCT APPROVALS 3
APPENDIX B – TECHNICAL SPECIFICATIONS 5
APPENDIX C – GLOSSARY OF TERMS 7
APPENDIX D – ORDERING INFORMATION 10

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 6 3

6. TECHNICAL APPENDICES

APPENDIX A – PRODUCT APPROVALS

CE Marking

The NV11 unit described in this manual set has been designed to comply with the
relevant sections of the following Harmonised European Standards:

 EN60950-1:2001
 EN60335-1:2002
 EN60335-2-82:2003

The unit complies with all the applicable essential requirements of the Standards.

RoHS

The following products, identified by the part numbers listed in the table below, are
compliant with the European Union Directive 2002/95/EC of the Restriction of the use
of certain Hazardous Substances (RoHS) in Electrical and Electronic Equipment.

Product Description Lead free date

NV11 Bank Note Acceptor Assembly All NV11

We hereby declare that lead (Pb), mercury (Hg), cadmium (Cd), hexavalent chromium
(Cr4-6), polybrominated biphenyls (PBB) and polybrominated diphenyl ethers (PBDE),
are not intentionally added to our products in amounts exceeding the maximum
concentration values as defined by RoHS regulations (except where the application of
any of those substances comes within the scope of the RoHS regulations exempted
applications).

All compliant products are clearly marked on the product and/or packaging.

All the information provided in this statement of compliance is accurate to the best of
our knowledge, as of the date of this publication being issued.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 6 4

WEEE

The European Union’s directive 2002/96/EC on Waste Electrical and Electronic

Equipment (WEEE) was adopted by the European Council and Parliament in 2003 with
a view to improving the collection and recycling of Waste Electrical and Electronic
Equipment throughout the EU, and to reduce the level of non-recycled waste. The
directive was implemented into law by many EU member states during 2005 and
2006.

Products and packaging that display the symbol (shown left) indicates
that this product must NOT be disposed of with other waste. Instead
it is the user’s responsibility to dispose of their Waste Electrical and
Electronic Equipment by handing it over to an approved reprocessor,
or by returning it to the original equipment manufacturer for
reprocessing.

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 6 5

APPENDIX B – TECHNICAL SPECIFICATIONS

The information contained here does not form part of a contract and is subject to
change without notice. Innovative Technology Ltd operates a policy of continual
product development; as such specifications may change from time to time.

Environment:

Minimum Maximum
Temperature +3 °C +50 °C
Humidity 5% 95 % non condensing

Power Requirements:

DC Voltage Minimum Nominal Maximum

Absolute limits 10.8 V 12 V 13.2 V
Supply ripple voltage 0V 0V 0.25 V @ 100 Hz
Supply Current
Standby 350 mA
Running 3A
Peak (motor stall) 3.5 A

WARNING! Ensure that the supply voltage to the NV11 is not

lower than 10.8 V and that the power supply can
Use suitable power supply
provide sufficient current to avoid incorrect
operation and excessive note rejects.

We recommend that your power supply is capable of supplying 12V DC at 4 A.

 For 12V operation, use TDK Lambda model SWS50-12. This power supply is
available from a variety of suppliers including Farnell (stock code 1184645) and
RS (stock code 466-5869).

Logic Levels:

Interface Logic Levels Logic Low Logic High

Inputs 0 V to +0.5 V +3.7 V to +12 V
Outputs (2.2 kΩ pull-up) +0.6 V Pull-up voltage of host
interface
Maximum current sink 50 mA per output

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 6 6

General Specifications:

Note Sizes Minimum Maximum

Width 60 mm 82 mm in cashbox
80mm in Note Float module
Length 115 mm 150 mm

Capacity
Storage 300 or 600 notes
Note Float module 30 notes

Weight
NV11 2.2 kg

Interface Protocol
eSSP; ccTalk (CC1, CC4)

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 6 7

APPENDIX C – GLOSSARY OF TERMS

Term Meaning

A Ampere

AC Alternating Current

ACK Acknowledge

AES Advanced Encryption Standard

ASSY Assembly

AV Average

AWG American Wire Gauge

AWP Amusement With Prizes

BNV Bank Note Validator

ccTalk Coin Controls Talk

COMMS Communications

CRC Cyclic Redundancy Check

DC Direct Current

DIA Diameter

DIP Dual Inline Package

ECB Electronic Code Book

EEPROM Electrically Erasable Programmable Read Only

Memory

eSSP Encrypted Smiley® Secure Protocol

FAQ Frequently Asked Questions

FIFO First In, First Out

GA General Assembly

GND Ground

Hz Hertz

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 6 8

Term Meaning

IF Interface

ITL Innovative Technology Ltd

LED Light Emitting Diode

LIFO Last In, First Out

mA milliampere

max maximum

MDB Multi Drop Bus

min minimum

mm millimetre

ms millisecond

MOD Modified (or Modification)

NV Note Validator

PCB Printed Circuit Board

PDF Portable Document Format

PiPS Pay-in Pay-out System

PROM Programmable Read Only Memory

PSU Power Supply Unit

QTY Quantity

RAM Random Access Memory

ROM Read Only Memory

Rx Receive

RoHS Restriction of the use of certain Hazardous

Substances

SIO Serial Input Output

SSP Smiley® Secure Protocol

SWG Standard Wire Gauge

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 6 9

Term Meaning

SWP Skill With Prizes

SYNC Synchronize

TTL Transistor Transistor Logic

Tx Transmit

USB Universal Serial Bus

V Volt

V_In Voltage In

WEEE Waste Electrical and Electronic Equipment

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set – Section 6 10

APPENDIX D – ORDERING INFORMATION

The following information is required to order an NV11 validator:

Product NV11 Consists of NV9USB validator, Note Float module,

bezel and cash box

Dataset Country code and Alternatively supply details of the currency and
variant note types you wish to use

Bezel Size 66 - 85 mm Please check the NV11 product page on the ITL
website for details of the bezels available

Cash Box 300 or 600 note Please check the NV11 product page on the ITL
capacity website for details of the range of available
cashboxes

Interface eSSP; ccTalk The NV11 can be used with CC1 or CC4 variants
of ccTalk

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine

 NV11 Manual Set

MAIN HEADQUARTERS Innovative Technology Ltd

Derker Street – Oldham – England - OL1 4EQ
Tel: +44 161 626 9999 Fax: +44 161 620 2090
E-mail: [email protected]
Web site: www.innovative-technology.co.uk

BRAZIL
[email protected]

CHINA
[email protected]

GERMANY
[email protected]

SPAIN
[email protected]

UNITED KINGDOM
[email protected]

UNITED STATES OF AMERICA

[email protected]

REST OF THE WORLD

[email protected]

Copyright © Innovative Technology Ltd 2012 GA963-2

Downloaded from www.Manualslib.com manuals search engine