MC600

IMPORTANT NOTE

Curtain Walling

Please note both CWCT and NHBC consider all storey height glazing to be a
curtain wall and therefore should be designed as such. Curtain walling
cannot be treated in the same way as window and door installations.
The following are requirements in undertaking a Curtain Walling project:

· Full elevation drawings must be produced. These drawings should

clearly indicate all perimeter interface details typically showing
water / vapour barriers, pressings / trims, fixing brackets / fixings
along with any fire stopping that may be required. This is not an
exhaustive list as other details may be required to suit specific
projects.

· All bracketry and fixings should be backed up by calculations from

a structural engineer to confirm suitability and meet site
requirements. Also, profiles need to be identified to suit site
conditions. These factors include screen sizes, fixing positions,
glass weight, barrier loadings & wind loadings.

· It may be a requirement to include for on-site water testing and pull

out testing. NHBC would require certification to the CWCT weather
test where glazing may span a floor as opposed to a BS6375-1
window / door weather test.

Please also consider acoustic, thermal and structural performance when

specifying curtain wall configuration and components.

IMPORTANT NOTE:
It would be expected that one or more members of installation teams
have been certified by the Systems supplier to demonstrate competence
and understanding of the system being installed.

ISSUED: JANUARY 2021 PAGE A01

 MC600

THIS PAGE IS INTENTIONALLY LEFT BLANK

PAGE A02 ISSUED: JANUARY 2021

 MC600

Main Index

MC Index Index.................................................................................................. A01 - A04

A MC Profiles

Specification Pages............................................................................ A05 - A08

Technical Information......................................................................... A09 - A14
Scale Profile Drawings....................................................................... A15 - A26

B MC Accessories

Photos & Drawings............................................................................. B03 - B16

C MC Sections

Scale Elevations................................................................................. C01 - C34

D MC Statics................................................................................................ D01 - D12

E MC Construction Drawings

NHBC Notice...................................................................................... E03

Bracket requirements......................................................................... E04
Horizontal Deductions........................................................................ E05
Stick Build Mullion Preparation - ACMC650....................................... E06
Stick Build Transom Preparation........................................................ E07
Stick Build Assembly - ACMC650 Spring Pin..................................... E08 - E09
Ladder Build Assembly - Shear Block................................................ E10
Drainage & Pressure Equalisation..................................................... E11
Reinforcing Sleeves........................................................................... E12
Splice Joints....................................................................................... E13
Transom / Mullion Sealing................................................................. E14
Sleeves............................................................................................... E15
Mullion on Transom Preparation........................................................ E16
Mullion on Transom Assembly........................................................... E17
Raked Head....................................................................................... E18
Glazing Details................................................................................... E19

ISSUED: JANUARY 2021 PAGE A03

 MC600

Updates
------------------------------------------------------------------------------------------------------------------------------------------------------

------------------------------------------------------------------------------------------------------------------------------------------------------
DATE PAGE DESCRIPTION
---------------------------------------------------------------------------------------------------------------------
26/01/2021 All Sections Removed old version of reinforcing sleeves;
-MC644, MC646, MC648, MC649, MC900, ACMC684,
ACMC686, ACMC688, ACMC689
Removed Facetted on plan sections & Accessories;
-MC670, MC671, MC672, MC675, MC676, MC677, SR014
Added New Shear Block for MC604;
-ACMC607
Added Raked Head;
-ACMC6052, ACMC6053, ACMC6054, ACMC6056, ACMC6058,
ACMC6059, ACMC693, ACMC646, ACMC647
Added;
-MC117, MC118, MC165, MC166

PAGE A04 ISSUED: JANUARY 2021

 MC600
PROFILES : SPECIFICATION PAGES

Specification

GENERAL DESCRIPTION

MC600 is a stick build curtain wall system suitable for low to high rise installations in commercial buildings.

Designed for quick and easy workshop preparation and on-site installation, MC600 is a cost effective system
which offers a high quality finish.

PROFILE SPECIFICATION

The sections are constructed of aluminium alloy extrusion to BS EN 755-9 and BS EN 12020, extruded from
6060 T6 alloy.

The aluminium alloy extrusion is pre-treated and finished either:-

a) Anodised to BS 3987: 1987, grade AA25 to a natural self colour.

b) Polyester powder organic coating to BS EN 12206-1.

GENERAL MANUFACTURING

After careful inspection of the extrusions, all visible areas shall be taped using our recommended protective
tape to help protect against any scratches.

Sections are cut with accurate 90° ends using Tungsten Carbide Tipped Saw Blades, operating at
approximately 3000 rpm. The isolators, MC601 can be inserted into the mullions/transoms prior to cutting.

The mullions are marked and drilled using the recommended drill jig ACMC695.

Transoms are drilled using recommended drill jig ACMC691 in preparation for the fixing bracket ACMC600
which is secured into position using ACET060 stainless steel self tapping screws.

On polyester powder coated finishes, great care should be taken to avoid getting gap sealer on visible
surfaces and should be removed as soon as possible with a clean cloth.

Care should be exercised when using products not supplied by Smart Systems Ltd as no responsibility can
be accepted.

ISSUED: JANUARY 2021 PAGE A05

 MC600
PROFILES : SPECIFICATION PAGES

Specification

DRAINAGE

As with all dry glazed systems, the system must be adequately drained and ventilated. Refer to drainage
details in manual, if in doubt ask the Technical Department.

WORKSHOP MANUFACTURING INFORMATION

After careful inspection of the extrusions, all visible areas shall be taped using our recommended protective
tape to help protect against any scratches.

Sections are cut with accurate 90° ends using Tungsten Carbide Tipped Saw Blades, operating at
approximately 3000 rpm. The isolator MC601 can be inserted into the mullions/transoms prior to cutting.

The mullions are marked to show the centre line of the transoms and are drilled with a 4mm dia. drill bit for
the ACMC600 brackets and a 6.5mm dia. drill bit for the ACMC650 anti-rotation spring pin using the
recommended drill jig ACMC695.

Transoms are drilled with a 3mm dia. drill bit using recommended drill jig ACMC691 in preparation for the
fixing bracket ACMC600 which is secured into position using ACET060 stainless steel self tapping screws.
The ACMC650 anti-rotation spring pin is slid into the position and secured by tightening the grub screw.
IMPORTANT NOTE: Maximum weight on ACMC600 / ACMC605 is 500kg.

All gaskets and transom end pads may be fitted in the workshop to save time on site.

ON SITE ASSEMBLY INFORMATION

After mullions are secured into position, the transoms are inserted between the vertical members until the
ACMC650 anti-rotation spring pin engages into the predrilled hole. Transom end pads should be sealed
using ACSIL05. Care should be taken to ensure the transom end pads are not dislodged at this point. The
transom is secured into position via the ACMC600 brackets using PUA028 stainless steel self tapping
screws.

Moulded corners shall be fitted between the gaskets and sealed using ACMX09830 EPDM adhesive.
ACMC630 glazing supports shall be positioned in preparation for the double glazed units.

GLAZING

Double glazed units shall be positioned on plastic packers on ACMC630 glazing supports with equal
distance on all sides.

Units are secured in position using DK154 with ACDK066 or MC655 fixing (not compatible with ACDK066)
held in place by ACMC610 or ACMC612 Hex Head Self Tapping Fixing Screw taking care not to exceed
torque of 4Nm at the recommended speed of 1500-1800rpm. Stitch plates may be used to secure the units
temporarily until all units are in position. Pressure plates shall be fitted at the top first, working downwards to
help avoid uneven fixings.

The cover caps are clipped in position using a rubber mallet taking care to strike the corners only to avoid
denting the section. Vertical cover caps are fitted first followed by the horizontal caps.

PAGE A06 ISSUED: JANUARY 2021

 MC600
PROFILES : SPECIFICATION PAGES

Specification

Construction Options

The MC600 Curtain Walling System may be installed as a stick,

ladder frame or as a screwed system.
Stick build is a fast method of fabrication and installation. The
Curtain Wall is taken to a site in stick form and the mullions are
first to be assembled - usually from the centre outwards. The
transoms are then fitted from the front of the Curtain Wall. Spring
Pins (ACMC650) fixed to the transoms, locate in pre-drilled holes
in the mullions and the transoms are then secured using a face
mounted bracket - ACMC600

Where ladder frames are used, shear blocks (ACMC602 /

ACMC603) are fixed to the mullions in the factory and 'ladders'
built and taken to the site ready assembled. The ladders are
connected together on site by locating open sided transoms
(MC615 / MC617) over the shear blocks, fixing them from the
front through the transom face, into the shear block screwports.
A clip plate (MC650 / MC651) is then pushed into place to close
the transom.

A final method of construction is to use two part mullions /

transoms (MC615 / MC650 and/or MC617 / MC651) and fix
using screws though the mullions into screwports within the
transoms.

ISSUED: JANUARY 2021 PAGE A07

 MC600
PROFILES : SPECIFICATION PAGES

Specification

MC600 Weather Performance (BS6375)

BS EN 1026: 2000 Air Permeability: Class 4 600Pa

BS EN 1027: 2000 Watertightness: Class 9a 600Pa
BS EN 12211: 2000 Resistance to Wind Load: Class 3 2400Pa

MC600 U Values

Contact Technical Department

PAGE A08 ISSUED: JANUARY 2021

 MC600
PROFILES : TECHNICAL INFORMATION

ix(cm4) iy(cm4) Pack

Number Picture Page Perim. Mec. Length
MF SA KL HP M
(mm) (mm) wx(cm3) wy(cm3) (m) pr.

7
DK052 A22 170 96 - - 1 ü ü ü ü
X
6.5
Y Y
X

7
DK053 A22 190 98 - - 1 ü ü ü ü
X
6.5
Y Y
X

DK154 A26 171 - - - 7 1 ü

X
Y Y
X

ETC090 A20 68 - - - 5 1 ü ü ü ü
X
Y Y
X

ETC091 A20 75 - - - 5 1 ü ü ü ü
X
Y Y
X

MC050 A22 206 102 - - 7 1 ü ü ü ü

X
Y Y
X

MC116 A26 85 34.5 - - 7 1 ü ü ü ü

X
Y Y
X

MC117 A26 48 18 - - 7 1 ü ü ü ü
X
Y Y
X

MC118 A26 105 49 - - 7 1 ü ü ü ü

X
Y Y
X
A = Outside MF = Mill Finish
B = Inside SA = Silver Anodised
KL = Basic Colour
HP = Special Colour
M = Dual Colour

ISSUED: JANUARY 2021 PAGE A09

 MC600
PROFILES : TECHNICAL INFORMATION

ix(cm4) iy(cm4) Pack

Number Picture Page Perim. Mec. Length
MF SA KL HP M
(mm) (mm) wx(cm3) wy(cm3) (m) pr.

MC165 A25 91 - - - 7 1 ü ü ü ü
X
Y Y
X

MC166 A25 103 - - - 7 1 ü ü ü ü

X
Y Y
X

MC601 A26 - - - - 7 1 ü
X
Y Y
X

MC602 A26 - - - - 7 1 ü
X
Y Y
X

71.6 31.7
MC603 A15 396 205 ---- ---- 7 1 ü ü ü ü
X
14.9 11.5
Y Y
X

MC604 A16 - - - - 7 1 ü ü ü ü
X
Y Y
X

23.5 20.7
MC612 A15 346 155 ---- ---- 7 1 ü ü ü ü
X
7.2 7.5
Y Y
X

120.6 35.2
MC614 A16 444 255 ---- ---- 7 1 ü ü ü ü
X
21.7 12.8
Y Y
X

116.9 22.7
MC615 A17 657 157 ---- ---- 6.5 1 ü ü ü ü
X
20.7 12.3
Y Y
X
A = Outside MF = Mill Finish
B = Inside SA = Silver Anodised
KL = Basic Colour
HP = Special Colour
M = Dual Colour

PAGE A10 ISSUED: JANUARY 2021

 MC600
PROFILES : TECHNICAL INFORMATION

ix(cm4) iy(cm4) Pack

Number Picture Page Perim. Mec. Length
MF SA KL HP M
(mm) (mm) wx(cm3) wy(cm3) (m) pr.

250 45
MC616 A18 496 305 --- ---- 7 1 ü ü ü ü
X
33.2 16.4
Y Y
X

232.2 25.8
MC617 A18 705 181 ---- ---- 6.5 1 ü ü ü ü
X
32.2 14.7
Y Y
X

380.4 59.5
MC618 A19 546 355 ---- ---- 7 1 ü ü ü ü
X
44.6 21.6
Y Y
X

575 68.5
MC619 A19 586 395 ---- ---- 7 1 ü ü ü ü
X
57 24.9
Y Y
X

1453.2 114.3
MC620 A17 695 505 ---- ---- 7 1 ü ü ü ü
X
110.42 41.6
Y Y
X

297 247.9
MC621 A21 692 312 ---- ---- 7 1 ü ü ü ü
X
45.9 45.1
Y Y
X

521.3 69.9
MC625 A20 625 353 ---- ---- 7 1 ü ü ü ü
X
57.4 25.4
Y Y
X

MC650 A17 221 94 - - 6.5 1 ü ü ü ü

X
Y Y
X

MC651 A18 271 119 - - 6.5 1 ü ü ü ü

X
Y Y
X
A = Outside MF = Mill Finish
B = Inside SA = Silver Anodised
KL = Basic Colour
HP = Special Colour
M = Dual Colour

ISSUED: JANUARY 2021 PAGE A11

 MC600
PROFILES : TECHNICAL INFORMATION

ix(cm4) iy(cm4) Pack

Number Picture Page Perim. Mec. Length
MF SA KL HP M
(mm) (mm) wx(cm3) wy(cm3) (m) pr.

MC652 A22 188 97 - - 7 1 ü ü ü ü

X
Y Y
X

MC653 A22 247 154 - - 7 1 ü ü ü ü

X
Y Y
X

MC654 A22 206 105 - - 7 1 ü ü ü ü

X
Y Y
X

MC655 A26 212 - - - 7 1 ü

X
Y Y
X

MC655H
PREPPED FOR
A23 212 - - - 7 1 ü
HORIZONTAL X
Y Y
X

MC655V
PREPPED FOR
A24 212 - - - 7 1 ü
VERTICAL X
Y Y
X

MC656 A16 171 69 - - 6.5 1 ü ü ü ü

X
Y Y
X

MC657 A21 298 152.9 - - 7 1 ü ü ü ü

X
Y Y
X

MC658 A21 - - - - 7 1 ü
X
Y Y
X
A = Outside MF = Mill Finish
B = Inside SA = Silver Anodised
KL = Basic Colour
HP = Special Colour
M = Dual Colour

PAGE A12 ISSUED: JANUARY 2021

 MC600
PROFILES : TECHNICAL INFORMATION

ix(cm4) iy(cm4) Pack

Number Picture Page Perim. Mec. Length
MF SA KL HP M
(mm) (mm) wx(cm3) wy(cm3) (m) pr.

MC663 A25 209 42 - - 6.5 1 ü ü ü ü

X
Y Y
X

MC664 A25 229 52 - - 6.5 1 ü ü ü ü

X
Y Y
X

MC665 A25 103 103 - - 7 1 ü ü ü ü

X
Y Y
X

MC666 A25 127 127 - - 7 1 ü ü ü ü

X
Y Y
X

MC667 A25 - - - - 7 1 ü ü ü ü
X
Y Y
X

23.1 13.8
MC693 A15 336 - ---- ---- 6 1 ü
X
7.6 5.5
Y Y
X

69.7 17
MC694 A16 375 - ---- ---- 6 1 ü
X 15.8 6.8
Y Y
X

142.9 22.3
MC696 A18 462 - ---- ---- 6 1 ü
X
37.7 8.9
Y Y
X

258.9 23.9
MC698 A19 507 - ---- ---- 6 1 ü
X
37.7 9.8
Y Y
X
A = Outside MF = Mill Finish
B = Inside SA = Silver Anodised
KL = Basic Colour
HP = Special Colour
M = Dual Colour

ISSUED: JANUARY 2021 PAGE A13

 MC600
PROFILES : TECHNICAL INFORMATION

ix(cm4) iy(cm4) Pack

Number Picture Page Perim. Mec. Length
MF SA KL HP M
(mm) (mm) wx(cm3) wy(cm3) (m) pr.

353.1 26.3
MC699 A19 547 - ---- ---- 6 1 ü
X
44.8 10.7
Y Y
X

UTL026 A20 160 160 - - 6 1 ü ü ü ü

X
Y Y
X

UTL052 A20 160 160 - - 6 1 ü ü ü ü

X
Y Y
X

A = Outside MF = Mill Finish

B = Inside SA = Silver Anodised
KL = Basic Colour
HP = Special Colour
M = Dual Colour

PAGE A14 ISSUED: JANUARY 2021

 MC600
PROFILE : SCALED PROFILE DRAWINGS

Primary Visible Side Secondary Visible Side

MC612
50mm Box

Sleeve Not
Available For
MC612
55

Will accept
UTL052 or
50mm x 30mm
insert

10.5 50

MC603
75mm Box
ACVS010

MC693
55

Sleeve

10.5 75

ACVS010

Scale 1:1

ISSUED: JANUARY 2021 PAGE A15

 MC600
PROFILE : SCALED PROFILE DRAWINGS

Primary Visible Side Secondary Visible Side

MC614
100mm Box
ACVS010

MC694
55

Sleeve

10.5 100

ACVS010

MC604
75mm Open Box

10.5 75
55

MC656
75mm Clip Plate

64.5

Scale 1:1

PAGE A16 ISSUED: JANUARY 2021

 MC600
PROFILE : SCALED PROFILE DRAWINGS

Primary Visible Side Secondary Visible Side

MC615
100mm Open Box

10.5 100
55

MC650
100mm Clip Plate

Scale 1:1
89.5

MC620
225mm Box
ACVS010

MC698
55

Sleeve

Scale 1:2
10.5 225

ISSUED: JANUARY 2021 PAGE A17

 MC600
PROFILE : SCALED PROFILE DRAWINGS

Primary Visible Side Secondary Visible Side

MC616
125mm Box
ACVS010

MC696
55

Sleeve

10.5 125
ACVS010

MC617
125mm Open Box
10.5 125
54.5

MC651
125mm Clip Plate

114.5

Scale 1:1

PAGE A18 ISSUED: JANUARY 2021

 MC600
PROFILE : SCALED PROFILE DRAWINGS

Primary Visible Side Secondary Visible Side

MC618 MC619
150mm Box 170mm Box

MC698
150

Sleeve

170
MC699
Sleeve

ACVS010

ACVS010
10.5

55
10.5

55

Scale 1:1

ISSUED: JANUARY 2021 PAGE A19

 MC600
PROFILE : SCALED PROFILE DRAWINGS

Primary Visible Side Secondary Visible Side

MC625 UTL026
90° Corner Mullion 40 x 40mm Box

40
40

UTL052
MC698 50 x 30mm Box
147

Sleeve

50 30

ACVS010
ETC090 ETC091
EPDM Carrier EPDM Carrier
11.5
21

21

90°
55 3.5

Scale 1:1

PAGE A20 ISSUED: JANUARY 2021

 MC600
PROFILE : SCALED PROFILE DRAWINGS

Primary Visible Side Secondary Visible Side

MC621
100mm x 110mm Transom

100
10.5
110

MC658
Pressure Plate
15.5

109

MC657
Capping
20

111.5
Scale 1:1

ISSUED: JANUARY 2021 PAGE A21

 MC600
PROFILE : SCALED PROFILE DRAWINGS

Primary Visible Side Secondary Visible Side

DK052 MC652 MC653

Horizontal Capping 50mm Vertical
Horizontal Capping
with Drip Capping
16 20 50
54.5

54.5

54.5
56.5

DK053 MC654 MC050

Vertical Capping Vertical Capping Vertical Capping
21 25 30
54.5

54.5

55

Scale 1:1

PAGE A22 ISSUED: JANUARY 2021

 MC600
PROFILE : SCALED PROFILE DRAWINGS

Primary Visible Side Secondary Visible Side

250
19

25
7

Ø6.5

250

7
250

25

Ø6.5
19

*Maximum distance on
50

fixing holes from end of

pressure plate = 80mm
25*

MC655H
Pre-Drilled Horizontal
Pressure Plate
Scale 1:1

ISSUED: JANUARY 2021 PAGE A23

 MC600
PROFILE : SCALED PROFILE DRAWINGS

Primary Visible Side Secondary Visible Side

Ø6.5
250

Ø6.5
125

MC655V
Pre-Drilled Vertical
Pressure Plate
Scale 1:1

PAGE A24 ISSUED: JANUARY 2021

 MC600
PROFILE : SCALED PROFILE DRAWINGS

Primary Visible Side Secondary Visible Side

MC665 MC666 MC667

Infill Infill Infill
28

34

42
24
30
38

MC165 MC166
Infill Infill
26

28

20 24

MC663 MC664
Infill Infill
22

22
13

13

41 51

Scale 1:1

ISSUED: JANUARY 2021 PAGE A25

 MC600
PROFILE : SCALED PROFILE DRAWINGS

DK154
MC655 Pressure Plate
Aluminium Pressure Plate
54.5
54.5
ACDK066 must be
ACDV066 is not used for each fixing
compatible with MC655
15.5

7.5 7.5
ACMC150

MC601 MC602
Insulator Insulator
45.5

55.5
30.5

40.5

10

10

10 5

MC116 MC117
10

10

Rebate Adaptor Rebate Adaptor

13 7

20

MC118
10

Rebate Adaptor

23

PAGE A26 ISSUED: JANUARY 2021

 MC600

Section B

Accessories

Photos & Drawings

ISSUED: JANUARY 2021 PAGE B01

 MC600

THIS PAGE IS INTENTIONALLY LEFT BLANK

PAGE B02 ISSUED: JANUARY 2021

 MC600
ACCESSORIES : PHOTOS & DRAWINGS

Image Part Code Pack Unit Application Colour

MF ü
ACDK066 1 each DK154 SA
KL
Fixing Plate for DK154 only HP
SSC
DO NOT USE WITH MC655 SMC
W
Z
PC

MF
ACET060 100 pack ACMC600 SA
KL
No.7 x 1" CSK S/S Self Tapper HP
SSC
SMC
W
Z
PC

MF
ACMC115 100 m MC612 SA
MC614 KL
Gasket for 24mm Glazing MC615 HP
MC616 SSC
SMC
MC617
W
15 MC618
MC619
Z ü
PC

MF
ACMC150 100 m MC655 SA
KL
Gasket for MC655 HP
SSC
SMC
W
Z ü
PC

MC603 MF ü
ACMC600 10 pack MC612 SA
MC614 KL
Transom Bracket Packed MC616 HP
with ACMC601 MC618 SSC
MC619 SMC
MC620 W
MC621 Z
MC625 PC

T-BARS
MF = Mill Finish W = White
ACVG65=2.5mm
ACVG66=3.0mm Screw (Grub) SA = Silver Anodised Z = Black
ACVL150=4.0mm
KL = Basic Colour
HP = Special Colour
SSC = Smooth Satin Chrome
SMC = Smokey Chrome
PC = Polished Chrome

ISSUED: JANUARY 2021 PAGE B03

 MC600
ACCESSORIES : PHOTOS & DRAWINGS

Image Part Code Pack Unit Application Colour

MF ü
ACMC602 20 pack MC615 SA
KL
Shear Block for MC615 HP
SSC
SMC
3
76. W
Z
PC

MF ü
ACMC603 20 pack MC617 SA
KL
Shear Block for MC617 HP
SSC
SMC
W
.7
98

Z
PC

MF
ACMC604 20 pack MC604 SA
MC615 KL
Transom End Block MC617 HP
SSC
SMC
W
Z ü
PC

MC603 MF
ACMC605 20 pack MC612 SA
MC614 KL
Transom End Block for MC616 HP
34m - 42mm Glazing MC618 SSC
MC619 SMC
MC620 W
MC621 Z ü
MC625 PC

MF
ACMC606 50 pack MC603 SA
KL
Transom End Pad for MC603 HP
SSC
SMC
W
Z ü
PC

T-BARS
MF = Mill Finish W = White
ACVG65=2.5mm
ACVG66=3.0mm Screw (Grub) SA = Silver Anodised Z = Black
ACVL150=4.0mm
KL = Basic Colour
HP = Special Colour
SSC = Smooth Satin Chrome
SMC = Smokey Chrome
PC = Polished Chrome

PAGE B04 ISSUED: JANUARY 2021

 MC600
ACCESSORIES : PHOTOS & DRAWINGS

Image Part Code Pack Unit Application Colour

MF ü
ACMC607 20 pack MC604 SA
KL
Shear Block for MC604 HP
SSC
SMC
9
53. W
Z
PC

MF
ACMC610 100 pack ACDK066 SA
DK154 KL
6.3mm x 53mm Hex Head MC655 HP
Self Tapper SSC
SMC
W
Z
PC

MF
ACMC612 100 pack ACDK066 SA
DK154 KL
6.3mm x 63mm Hex Head MC655 HP
Self Tapper SSC
SMC
W
Z
PC

MF
ACMC613 50 pack MC612 SA
KL
Transom End Pad for MC612 HP
SSC
SMC
W
Z ü
PC

MF
ACMC614 50 pack MC614 SA
KL
Transom End Pad for MC614 HP
SSC
SMC
W
Z ü
PC

T-BARS
MF = Mill Finish W = White
ACVG65=2.5mm
ACVG66=3.0mm Screw (Grub) SA = Silver Anodised Z = Black
ACVL150=4.0mm
KL = Basic Colour
HP = Special Colour
SSC = Smooth Satin Chrome
SMC = Smokey Chrome
PC = Polished Chrome

ISSUED: JANUARY 2021 PAGE B05

 MC600
ACCESSORIES : PHOTOS & DRAWINGS

Image Part Code Pack Unit Application Colour

MF
ACMC616 50 pack MC616 SA
KL
Transom End Pad for MC616 HP
SSC
SMC
W
Z ü
PC

MF
ACMC618 50 pack MC618 SA
KL
Transom End Pad for MC618 HP
SSC
SMC
W
Z ü
PC

MF
ACMC619 50 pack MC619 SA
KL
Transom End Pad for MC619 HP
SSC
SMC
W
Z ü
PC

MF
ACMC115
ACMC624 20 pack SA
MC612
KL
MC614
Moulded Corner Gasket for MC615 HP
6mm, 24mm & 34mm Glazing SSC
MC616
MC617 SMC

MC618 W
MC619 Z
PC

MF
ACMC628 20 pack ACSC212
SA
MC612
KL
MC614
Moulded Corner Gasket for MC615
HP
10mm, 28mm & 38mm Glazing SSC
MC616
SMC
MC617
W
MC618
Z
MC619
PC

T-BARS
MF = Mill Finish W = White
ACVG65=2.5mm
ACVG66=3.0mm Screw (Grub) SA = Silver Anodised Z = Black
ACVL150=4.0mm
KL = Basic Colour
HP = Special Colour
SSC = Smooth Satin Chrome
SMC = Smokey Chrome
PC = Polished Chrome

PAGE B06 ISSUED: JANUARY 2021

 MC600
ACCESSORIES : PHOTOS & DRAWINGS

Image Part Code Pack Unit Application Colour

MC612 MF ü
ACMC630 20 pack SA
45 MC614 KL
Glazing Support (100mm) MC615 HP
MC616 SSC
MC617 SMC
W
MC618
Z
MC619 PC

MC612 MF ü
ACMC631 20 pack SA
55 MC614 KL
Glazing Support (100mm) MC615 HP
for 34mm - 42mm MC616 SSC
MC617 SMC
W
MC618
Z
MC619 PC

MF
ACMC632 20 pack ACSC208
SA
MC612
KL
MC614
Moulded Corner Gasket for MC615
HP
14mm, 32mm & 42mm Glazing SSC
MC616
SMC
MC617
W
MC618
MC619
Z ü
PC

ACMC203
MF ü
ACMC644 10 pack SA
MC612
KL
MC614
Cover Cap for Splice Joint MC615
HP
SSC
MC616
SMC
MC617
W
MC618
Z
MC619
PC

MC612
MF ü
ACMC646 50 pack SA
MC614 KL
Foam End Block for Raked MC615 HP
Heads MC616 SSC
For Glazing 6mm - 32mm SMC
MC617
53.5

W
MC618 Z
MC619 PC

T-BARS
MF = Mill Finish W = White
ACVG65=2.5mm
ACVG66=3.0mm Screw (Grub) SA = Silver Anodised Z = Black
ACVL150=4.0mm
KL = Basic Colour
HP = Special Colour
SSC = Smooth Satin Chrome
SMC = Smokey Chrome
PC = Polished Chrome

ISSUED: JANUARY 2021 PAGE B07

 MC600
ACCESSORIES : PHOTOS & DRAWINGS

Image Part Code Pack Unit Application Colour

MC612
MF ü
ACMC647 50 pack SA
MC614 KL
Foam End Block for Raked MC615 HP
Heads MC616 SSC
63.5

For Glazing 34mm - 42mm SMC

MC617
W
MC618 Z
MC619 PC

MC612 MF ü
ACMC650 1 each SA
MC614 KL
Spring Pin With Hook MC615 HP
MC616 SSC
MC617 SMC
W
MC618
Z
MC619 PC

MC612 MF ü
ACMC651 1 each SA
MC614 KL
Fixed Anti-Rotation Pin with MC615 HP
Hook MC616 SSC
MC617 SMC
W
MC618
Z
MC619 PC

MF
ACMC660 50 pack DK053 SA
KL
End Cap HP
SSC
SMC
W
Z
PC

MF
ACMC661 50 pack DK052 SA
KL
End Cap HP
SSC
SMC
W
Z
PC

T-BARS
MF = Mill Finish W = White
ACVG65=2.5mm
ACVG66=3.0mm Screw (Grub) SA = Silver Anodised Z = Black
ACVL150=4.0mm
KL = Basic Colour
HP = Special Colour
SSC = Smooth Satin Chrome
SMC = Smokey Chrome
PC = Polished Chrome

PAGE B08 ISSUED: JANUARY 2021

 MC600
ACCESSORIES : PHOTOS & DRAWINGS

Image Part Code Pack Unit Application Colour

MF
ACMC663 1 each MC603 SA
KL
0
100 1000mm Sleeve for MC603 HP
with ACVS010 inserts SSC
SMC
Produced from MC693 W
Z
PC

MF
ACMC664 1 each MC614 SA
KL
00

1000mm Sleeve for MC614 HP

10

with ACVS010 inserts SSC

SMC
Produced from MC694 W
Z
PC

MF
ACMC666 1 each MC616 SA
KL
00
10

1000mm Sleeve for MC616 HP

with ACVS010 inserts SSC
SMC
Produced from MC696 W
Z
PC

MF
ACMC668 1 each MC618 SA

0
MC620 KL
1 00
1000mm Sleeve for MC618 MC625 HP
with ACVS010 inserts SSC
SMC
Produced from MC698 W
Z
PC

MF
ACMC669 1 each MC619 SA
KL
00
10

1000mm Sleeve for MC619 HP

with ACVS010 inserts SSC
SMC
Produced from MC699 W
Z
PC

T-BARS
MF = Mill Finish W = White
ACVG65=2.5mm
ACVG66=3.0mm Screw (Grub) SA = Silver Anodised Z = Black
ACVL150=4.0mm
KL = Basic Colour
HP = Special Colour
SSC = Smooth Satin Chrome
SMC = Smokey Chrome
PC = Polished Chrome

ISSUED: JANUARY 2021 PAGE B09

 MC600
ACCESSORIES : PHOTOS & DRAWINGS

Image Part Code Pack Unit Application Colour

MF
ACMC691 1 each MC612 SA
MC614 KL
Transom Drill Jig MC616 HP
Dual Purpose: SSC
-Transom Brackets
MC618
SMC
-Shear Blocks MC619 W
Z
PC

MF
ACMC692 1 each MC614 SA
MC615 KL
Mullion Drill Jig for Shear MC616 HP
Block SSC
MC617
SMC
MC618 W
MC619 Z
PC

MF
ACMC693 1 each MC614 SA
MC615 KL
Raked Head Drill Jig MC616 HP
SSC
MC617
SMC
MC618 W
MC619 Z
PC

MF
ACMC695 1 each MC612 SA
MC614 KL
Mullion Drill Jig for ACMC650 MC616 HP
& ACMC651 SSC
MC618
SMC
MC619 W
Z
PC

MF
ACMC6052 1 each MC612 SA
30
KL
Angle Bracket for MC612 HP
SSC
SMC
W
Z
PC

T-BARS
MF = Mill Finish W = White
ACVG65=2.5mm
ACVG66=3.0mm Screw (Grub) SA = Silver Anodised Z = Black
ACVL150=4.0mm
KL = Basic Colour
HP = Special Colour
SSC = Smooth Satin Chrome
SMC = Smokey Chrome
PC = Polished Chrome

PAGE B10 ISSUED: JANUARY 2021

 MC600
ACCESSORIES : PHOTOS & DRAWINGS

Image Part Code Pack Unit Application Colour

MF
5
ACMC6053 1 each MC603 SA
53.
KL
Angle Bracket for MC603 HP
SSC
SMC
W
Z
PC

MF

80
ACMC6054 1 each MC614 SA
KL
Angle Bracket for MC614 HP
SSC
SMC
W
Z
PC

MF
5 ACMC6056 1 each MC616 SA
102.
KL
Angle Bracket for MC616 HP
SSC
SMC
W
Z
PC

MF
ACMC6058 1 each MC618 SA
128
KL
Angle Bracket for MC618 HP
SSC
SMC
W
Z
PC

MF
.5 ACMC6059 1 each MC619 SA
146
KL
Angle Bracket for MC619 HP
SSC
SMC
W
Z
PC

T-BARS
MF = Mill Finish W = White
ACVG65=2.5mm
ACVG66=3.0mm Screw (Grub) SA = Silver Anodised Z = Black
ACVL150=4.0mm
KL = Basic Colour
HP = Special Colour
SSC = Smooth Satin Chrome
SMC = Smokey Chrome
PC = Polished Chrome

ISSUED: JANUARY 2021 PAGE B11

 MC600
ACCESSORIES : PHOTOS & DRAWINGS

Image Part Code Pack Unit Application Colour

MF
ACSC208 100 m MC612 SA
MC614 KL
Gasket for 32mm Glazing MC615 HP
MC616 SSC
SMC
MC617
W
7.5 MC618
MC619
Z ü
PC

MF
ACSC212 100 m MC612 SA
MC614 KL
Gasket for 28mm Glazing MC615 HP
MC616 SSC
SMC
MC617
W
11.
5
MC618 Z
MC619 PC

MF
ACVS010 7.3 m MC693 SA
MC694 KL
Spacer for Inserts MC696 HP
MC698 SSC
SMC
MC699
W
Z
PC

MF
PUA028 100 pack ACMC600 SA
KL
No.10 x 1" Pan Head HP
Self Tapper SSC
SMC
W
Z
PC

MF
SA
KL
HP
SSC
SMC
W
Z
PC

T-BARS
MF = Mill Finish W = White
ACVG65=2.5mm
ACVG66=3.0mm Screw (Grub) SA = Silver Anodised Z = Black
ACVL150=4.0mm
KL = Basic Colour
HP = Special Colour
SSC = Smooth Satin Chrome
SMC = Smokey Chrome
PC = Polished Chrome

PAGE B12 ISSUED: JANUARY 2021

 MC600
STANDARD ACCESSORIES

Image Part Code Pack Unit Application Colour

MF ü
ACMX09700 1 each SA
KL
Alu. Polish HP
SSC
SMC
W
Z
PC

MF
ACMX09761 1 each SA
KL
Maxi Gloss HP
SSC
SMC
W
Z
PC

MF
ACMX09762 1 each SA
KL
Alu. Bright HP
SSC
SMC
W
Z
PC

MF
ACMX09763 1 each SA
KL
Teflon Spray HP
SSC
SMC
W
Z
PC

MF
ACMX09764 1 each SA
KL
Maxi Clean HP
SSC
SMC
W
Z
PC

T-BARS
MF = Mill Finish W = White
ACVG65=2.5mm
ACVG66=3.0mm Screw (Grub) SA = Silver Anodised Z = Black
ACVL150=4.0mm
KL = Basic Colour
HP = Special Colour
SSC = Smooth Satin Chrome
SMC = Smokey Chrome
PC = Polished Chrome

ISSUED: JANUARY 2021 PAGE B13

 MC600
STANDARD ACCESSORIES

Image Part Code Pack Unit Application Colour

MF
ACMX09765 1 each SA
KL
Alu. Cleaner HP
SSC
SMC
W
Z
PC

MF
ACMX09770 1 each SA
KL
Roll & Wrap 100mm HP
SSC
SMC
W
Z
PC

MF
ACMX09775 1 each SA
KL
Grip Handwrap HP
SSC
SMC
W
Z
PC

MF
ACMX09801 1 each SA
KL
Protective Tape 50mm HP
SSC
SMC
W
Z
PC

MF
ACMX09802 1 each SA
KL
Protective Tape 70mm HP
SSC
SMC
W
Z
PC

T-BARS
MF = Mill Finish W = White
ACVG65=2.5mm
ACVG66=3.0mm Screw (Grub) SA = Silver Anodised Z = Black
ACVL150=4.0mm
KL = Basic Colour
HP = Special Colour
SSC = Smooth Satin Chrome
SMC = Smokey Chrome
PC = Polished Chrome

PAGE B14 ISSUED: JANUARY 2021

 MC600
STANDARD ACCESSORIES

Image Part Code Pack Unit Application Colour

MF
ACMX09803 1 each SA
KL
Protective Tape 100mm HP
SSC
SMC
W
Z
PC

MF
ACSIL04 1 each SA
KL ü
Sealing Glue HP
Order with suffix of KL SSC
colour (eg.ACSIL04KL005) SMC
or BL=Black/WP=White/
CL=Clear
W ü
Z ü
PC

MF
ACSIL05 1 each SA
KL
Rubber Sealant HP
SSC
SMC
W
Z
PC

MF
ACSIL08 1 each SA
KL
Silicon Gun HP
SSC
SMC
W
Z
PC

MF
ACSIL013 1 each SA
KL
Glue for Mitre HP
SSC
SMC
W
Z
PC

T-BARS
MF = Mill Finish W = White
ACVG65=2.5mm
ACVG66=3.0mm Screw (Grub) SA = Silver Anodised Z = Black
ACVL150=4.0mm
KL = Basic Colour
HP = Special Colour
SSC = Smooth Satin Chrome
SMC = Smokey Chrome
PC = Polished Chrome

ISSUED: JANUARY 2021 PAGE B15

 MC600
STANDARD ACCESSORIES

Image Part Code Pack Unit Application Colour

MF ü
ACSIL014 1 each SA
KL
Anti-Corrosion Coating HP
SSC
SMC
W
Z
PC

MF
ACUN3900 1 each SA
KL
Gasket Roller HP
SSC
SMC
W
Z
PC

MF
SA
KL
HP
SSC
SMC
W
Z
PC

MF
SA
KL
HP
SSC
SMC
W
Z
PC

MF
SA
KL
HP
SSC
SMC
W
Z
PC

T-BARS
MF = Mill Finish W = White
ACVG65=2.5mm
ACVG66=3.0mm Screw (Grub) SA = Silver Anodised Z = Black
ACVL150=4.0mm
KL = Basic Colour
HP = Special Colour
SSC = Smooth Satin Chrome
SMC = Smokey Chrome
PC = Polished Chrome

PAGE B16 ISSUED: JANUARY 2021

 MC600

Section C

Sections

Scale Elevations

6
7

9 3
1

2 10

8
SM
AR
TW
4
AL
L

ISSUED: JANUARY 2021 PAGE C01

 MC600

12
11
17 15

14
13
18
16
SM
AR
T WA
LL

S
LU
IDEP
VIS O GL
OF VIS
OL
D

PAGE C02 ISSUED: JANUARY 2021

 MC600
SECTIONS

Detail 1a - End Mullion

CLASS B
4
AIRTIGHT VAPOUR
IL0
BARRIER
ACS
MC694

MC614
ETC091

ACET070

PLEASE NOTE:
Pressings and Membranes are shown for illustration
only. Membranes should be specified to suit
building interface and correctly bonded to structure.
Please refer to relevant suppliers for details.

100
All brackets, fixings and membranes should be
specified by a certified structural engineer.

ETC091

164.5
ACVS010
ACET070

CLASS B
WATERPROOF
BREATHABLE BARRIER

ACSC212
MC665
28

PERIMETER POINTING AS
SPECIFIED WITH BACKER ROD
DK154
21

MC601
ACDK066
ACMC610 DK053 15
10
Nom. 5 54.5

Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE C03

 MC600
SECTIONS

Detail 1b - End Mullion

AC
SI
UTL046 L0
4
MC694

MC614

CLASS B
AIRTIGHT VAPOUR ACET070
BARRIER

ETC091

100
PLEASE NOTE:
Pressings and Membranes are shown for illustration
only. Membranes should be specified to suit building
interface and correctly bonded to structure.
Please refer to relevant suppliers for details.

All brackets, fixings and membranes should be

specified by a certified structural engineer.

ETC091

164.5
ACVS010

CLASS B ACET070
WATERPROOF
BREATHABLE BARRIER

UTL086
ACSC212
04
SIL
AC

28

PERIMETER POINTING
AS SPECIFIED WITH
UTL035 DK154
21

BACKER ROD

MC601

ACMC610 DK053 15
10
Nom. SITE DEPENDANT 54.5

Do Not Scale From This Drawing

PAGE C04 ISSUED: JANUARY 2021

 MC600
SECTIONS

Detail 1c - Open Box Mullion

CLASS B
AIRTIGHT VAPOUR
BARRIER

MC615

MC650
ACET070

ETC091

PLEASE NOTE:
Pressings and Membranes are shown for illustration
only. Membranes should be specified to suit building
interface and correctly bonded to structure.
Please refer to relevant suppliers for details.

100
All brackets, fixings and membranes should be
specified by a certified structural engineer.

ETC091

164.5
ACET070

CLASS B
WATERPROOF
BREATHABLE BARRIER

ACSC212
MC665
28

PERIMETER POINTING AS
SPECIFIED WITH BACKER ROD
ACMC150
21

MC655 MC601
ACMC610 DK053 15
10
Nom. 5 54.5

Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE C05

 MC600
SECTIONS

Detail 1d - Open Box Mullion

CLASS B
AIRTIGHT VAPOUR
BARRIER

MC615

MC650
ACET070

ETC091

PLEASE NOTE:
Pressings and Membranes are shown for illustration
only. Membranes should be specified to suit building
interface and correctly bonded to structure.
Please refer to relevant suppliers for details.

100
All brackets, fixings and membranes should be
specified by a certified structural engineer.

ETC091

174.5
ACET070
CLASS B
WATERPROOF
BREATHABLE BARRIER
ACSC208
ACSC115

MC666
42

PERIMETER POINTING AS
SPECIFIED WITH BACKER ROD
DK154
21

MC602
ACDK066 ACMC612 DK053 15
10
Nom. 10 54.5

Do Not Scale From This Drawing

PAGE C06 ISSUED: JANUARY 2021

 MC600
SECTIONS

Detail 2a - Mullion Detail

55

MC694

MC614

100

164.5
ACVS010

ACSC212
28

28

DK053 DK154
21

MC601

ACDK066 ACMC610 15
54.5

Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE C07

 MC600
SECTIONS

Detail 2b - Mullion Detail

MC615

MC650

100

164.5
ACSC212
28

28

ACMC150
21

MC601

ACMC610 DK053 15
MC655
54.5

Do Not Scale From This Drawing

PAGE C08 ISSUED: JANUARY 2021

 MC600
SECTIONS

Detail 2c - Mullion Detail

MC615

MC650

100

174.5
ACSC208
42

42

DK154
21

MC602

ACMC612 DK053 15
ACDK066
54.5

Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE C09

 MC600
SECTIONS

Detail 3a - Mullion Detail

77 5 55

MC694

MC614

ACET840

ETC308
ACVS010

ACSC212
28
28

ETC424N DK053 DK154

21

MC601

ACDK066
ACMC610 15
54.5

Do Not Scale From This Drawing

PAGE C10 ISSUED: JANUARY 2021

 MC600
SECTIONS

Detail 3b - Mullion Detail

82 55
5

MC612

ACET840

ETC616

ACSC212
28

28
ETC628 DK154
ACDK066
MC601
ACMC610
50

MC653

15
54.5

Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE C11

 MC600
SECTIONS

Detail 4a - Mullion with Smart Wall Jamb

164.5
100 28

DK154
ACSC212
ACVS010

MC601
ACET062
MC614

15
54.5
55
MC694

ACMC610
3

DK053
ACW20038

21

ACDK066
IMP016

MC665
IMP210

IMP035

PUA028
IMP036N

PLEASE NOTE:
Refer to the latest Smart Wall
manual for further details

NOT TO SCALE

Do Not Scale From This Drawing

PAGE C12 ISSUED: JANUARY 2021

 MC600
SECTIONS

Detail 5a - Top Transom

CLASS B
MASTIC SEALANT WATERPROOF
BREATHABLE BARRIER CLASS B
WITH BACKER ROD AIRTIGHT VAPOUR
BARRIER

MC665
Nom.
10
10

MC612
MC652
56.5

55
ACMC610
ACMC650
15

MC601
ACDK066
ACSC212
DK154
20

28

113.5

PLEASE NOTE:
Refer to Section E for further
information on top of mullion fixing

Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE C13

 MC600
SECTIONS

Detail 5b - Top Transom

CLASS B
WATERPROOF
BREATHABLE BARRIER

MASTIC SEALANT CLASS B

WITH BACKER ROD AIRTIGHT VAPOUR
BARRIER
ACSC115
MC666
Nom.
10
10

MC652
56.5

55
ACMC612
15

MC612
MC601 ACMC650
MC655 ACSC208
ACMC150

20 42

123.5

PLEASE NOTE:
Refer to Section E for further
information on top of mullion fixing

Do Not Scale From This Drawing

PAGE C14 ISSUED: JANUARY 2021

 MC600
SECTIONS

Detail 6a - Transom

55

ACMC650

MC614

100
MC601
ACMC630

163.5
ACSC212
28

28
MC652

20
ACMC150

15
ACMC610

54.5
MC655

Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE C15

 MC600
SECTIONS

Detail 6b - Transom

ACMC650
55

MC614

100
MC602
ACMC631

173.5
ACSC208

42
MC652

20
DK154

15
ACDK066

ACMC612

54.5

Do Not Scale From This Drawing

PAGE C16 ISSUED: JANUARY 2021

 MC600
SECTIONS

Detail 6c - Transom

55

ACMC650

MC614

100
MC601
ACMC630

163.5
ACSC212
MC116

28
6

MC652

20
DK154

15
ACMC610

54.5
ACDK066

Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE C17

 PAGE
28
PLEASE NOTE: SECTIONS
Refer to Section E for further
information on shear blocks

C18
MC652 ACMC630 ACMC602 MC615

ISSUED: JANUARY 2021

ACDK066

ACMC610
55

54.5
MC600

15

Do Not Scale From This Drawing

MC601 MC650
ACSC212
Detail 6d - Open Box Transom

DK154

20 28 100

163.5
 MC600
SECTIONS

Detail 7a - Transom Above Door

163.5
20 28 100

ACMC212
MC652 ACMC630 ACET062 MC614
15

ACDK066 ACMC650
ACMC610
54.5

55
MC601
19

3
DK154
TRIMMED FOR
MC663
MC665 ACW20038

IMP110

IMP011

PLEASE NOTE:
Transom / Mullion must be
selected bases on Ixx / Iyy value
required to suit site conditions.

IMP120

PLEASE NOTE:
Refer to the latest Smart Wall
manual for threshold details

NOT TO SCALE

Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE C19

 MC600
SECTIONS

Detail 7b - Transom Above Door

173.5
20 42 100

ACMC208
MC652
ACMC631 ACET062 MC614
ACDK066
ACMC6350
ACMC612
54.5

55
MC602

3
DK154
TRIMMED FOR ACW20038
MC663

IMP110

IMP011

PLEASE NOTE:
Transom / Mullion must be
selected bases on Ixx / Iyy value
required to suit site conditions.

IMP120

PLEASE NOTE:
Refer to the latest Smart Wall
manual for threshold details

NOT TO SCALE

Do Not Scale From This Drawing

PAGE C20 ISSUED: JANUARY 2021

 28
SECTIONS

Refer to Section E for further

information on bottom of mullion fixing

20
ACSC212

MC652 ACMC630 MC614

ACMC650
ACDK066

ACMC610
PLEASE NOTE:
Pressings and Membranes are shown for illustration only.
Membranes should be specified to suit building interface
and correctly bonded to structure.
55

Please refer to relevant suppliers for details.

54.5
All brackets, fixings and membranes should be specified
by a certified structural engineer.
MC600

MC601
Detail 8a - Cill

PACKER AC
S IL
DK154 0 4
ACET070

Do Not Scale From This Drawing

ACSC115 ACET070
MC665
UTL007 ETC091

ISSUED: JANUARY 2021

CILL PRESSINGS
BY OTHERS CLASS B
CLASS B AIRTIGHT VAPOUR

PAGE
WATERPROOF BARRIER
BREATHABLE BARRIER
HOLDING
DOWN CLIPS

C21
 42

PAGE
SECTIONS

Refer to Section E for further

information on bottom of mullion fixing

C22
20
ACSC208

MC652 ACMC631 ACMC650

MC614

ACDK066

ISSUED: JANUARY 2021

ACMC612
PLEASE NOTE:
Pressings and Membranes are shown for illustration only.
Membranes should be specified to suit building interface
and correctly bonded to structure.
55

Please refer to relevant suppliers for details.

54.5
All brackets, fixings and membranes should be specified
by a certified structural engineer.

MC602
MC600

Detail 8b - Cill

PACKER
DK154
ACET070

Do Not Scale From This Drawing

MC666 ACSC212 ACET070 ETC091
04
UTL007 S IL
AC

CILL PRESSINGS
BY OTHERS CLASS B
CLASS B AIRTIGHT VAPOUR
WATERPROOF BARRIER
BREATHABLE BARRIER
HOLDING
DOWN CLIPS
 28
SECTIONS

Refer to Section E for further

information on bottom of mullion fixing

20
ACSC212

MC652 ACMC630 ACMC602 MC650

ACDK066 MC615
ACMC610
55

54.5
MC600

MC601
Detail 8c - Cill

DK154 PACKER

Do Not Scale From This Drawing

ACSC115 ACET070
MC665
UTL007

ISSUED: JANUARY 2021

PLEASE NOTE:
Pressings and Membranes are shown for illustration only.
CILL PRESSINGS Membranes should be specified to suit building interface
and correctly bonded to structure.
BY OTHERS Please refer to relevant suppliers for details.

PAGE
All brackets, fixings and membranes should be specified
by a certified structural engineer.

C23
 MC600
SECTIONS

Detail 9 - Opening Vent to Transom

28

ETC628

82
ETC616

20
ACET840

MC652 5
28
ACDK066

ACMC610
56.5

55

ACMC630
UTL052

DK154 MC612
MC601 ACSC212

28
113.5

Do Not Scale From This Drawing

PAGE C24 ISSUED: JANUARY 2021

 MC600
SECTIONS

Detail 10a - 90° Corner

55

MC625

MC698
147

ACVS010

28
ACSC212
21

MC601
90°

DK053

54 ACMC610
.5
ACDK066

DK154
BESPOKE
UTL026 PACKER
NOT TO SCALE

Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE C25

 MC600
SECTIONS

Detail 10b - 90° Corner

PLEASE NOTE:
Brackets and Fixing shown are for illustration only.
Brackets and Fixings should be specified by a
structural engineer.

55
AC
SI
L0
4

MC614
ACET070

ACET070
MC694
100

UTL047
°
90
164.5

ACVS010

ACSC212 Insulated Panel by others

28

DK154 DK053

MC601
ACDK066
ACMC610
15

54.5

NOT TO SCALE

Do Not Scale From This Drawing

PAGE C26 ISSUED: JANUARY 2021

 MC600
SECTIONS

Detail 11a - Auto Sliding Door Head

164.5

28 100

ACSC150
ACSC150
ACMC630 ACMC650 MC621

MC657

ACMC610
111.5

MC601

MC658

ACMC610

MC663
ACMC650
ACSC150 IMP114
TRIMMED FLUSH
MC601 IMP121
TO MC663 ACDV205

6
170.5

PLEASE NOTE:
For further details on Auto
Slide Doors, please refer to
Smart Wall Manual.

NOT TO SCALE

Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE C27

 MC600
SECTIONS

Detail 11b - Auto Sliding Door Head

163.5

28 100

MC652 ACMC630 MC614

ACMC650
MC601
54.5

55

ACSC212 UTL059
MODIFIED

DK154
151.5

Insulated Panel by others

PUA028

MC652

ACMC630

MC601
54.5

MC614
ACMC650
MC663
IMP114 IMP121
DK154
TRIMMED FOR MC663 ACDV205

169.5

PLEASE NOTE:
For further details on Auto
Slide Doors, please refer to
Smart Wall Manual.

NOT TO SCALE

Do Not Scale From This Drawing

PAGE C28 ISSUED: JANUARY 2021

 164.5
100
SECTIONS

ACSC150
ACSC212 ACMC650
MC657
ACMC630 MC601 MC621

ACMC610

MC658

111.5
MC600

ACMC610

Do Not Scale From This Drawing

Detail 12a - Auto Sliding Door Head

ISSUED: JANUARY 2021

ACMC650
MC601
ACSC212

PAGE
PLEASE NOTE:
ACSC150 For further details on Auto
Slide Doors, please refer to
28 Smart Wall Manual.

C29
 163.5
28

PAGE
SECTIONS
MC652 ACMC630 MC614

C30
MC601
ACMC650

56.5

ISSUED: JANUARY 2021

UTL059
ACSC212 MODIFIED
PUA028
DK154

151.5
MC600

MC652

Do Not Scale From This Drawing

PLEASE NOTE:
For further details on Auto
Slide Doors, please refer to

56.5
Smart Wall Manual.
Detail 12b - Auto Sliding Door Head

ACMC630

MC614
ACMC650
100
MC601
 MC600
SECTIONS

Detail 13 - Auto Sliding Door Stile

IMP040

IMP114
6

ACDV205

IMP114
MC614

PLEASE NOTE:
MC694 For further details on Auto
100

Slide Doors, please refer to

Smart Wall Manual.
164.5

ACVS010

ACSC212

MC663
28

DK154
TRIMMED FOR MC663

DK053

MC601
ACDK066
ACMC610
15
54.5
NOT TO SCALE

Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE C31

 MC600
SECTIONS

Detail 14 - Auto Sliding Door Stile

IMP013

IMP039

MC614

MC694

164.5
ACVS010

ACSC212

MC663
28

DK154
TRIMMED FOR MC663

DK053

MC601 ACDK066

PLEASE NOTE: ACMC610

For further details on Auto 15
Slide Doors, please refer to
Smart Wall Manual. 54.5
NOT TO SCALE

Do Not Scale From This Drawing

PAGE C32 ISSUED: JANUARY 2021

 MC600
SECTIONS

Detail 15 - Visoglide Plus Head

164.5
20 28 100

ACMC150
ACSC212
ACMC630 ACMC650

MC657 MC621

MC658

ACMC610

MC601
111.5

110
MC601

ACMC610

MC665

ACMC650
ACMC150
ACW20038

ACIM062

VG518

VG520

PLEASE NOTE:
For further details on Sliding
Doors please refer to the VG560
Visoglide Plus Manual.

NOT TO SCALE

Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE C33

 CLASS B
PLEASE NOTE: 55 AIRTIGHT VAPOUR

PAGE
BARRIER
For further details on Sliding SECTIONS
Doors please refer to the MC694 MC614
Visoglide Plus Manual.

ACW20038 ETC091

C34
VG511N
ACIM062

ACET070

ISSUED: JANUARY 2021

ACVS010

ETC091

ACET070

ACSC212
MC600

VG520

CLASS B
WATERPROOF
BREATHABLE
BARRIER

MC665

Do Not Scale From This Drawing

PLEASE NOTE:
Pressings and Membranes are shown for illustration
Detail 16 - Visoglide Plus Jamb

only. Membranes should be specified to suit

building interface and correctly bonded to structure.
Please refer to relevant suppliers for details. PERIMETER
POINTING AS
SPECIFIED WITH
All brackets, fixings and membranes should be
BACKER ROD
specified by a certified structural engineer. MC665
17

ACDK066

MC601 DK053 ACMC610

DK154 54.5 5
TRIMMED FOR MC663
NOT TO SCALE 10
Nom.
 MC600

Section D

Statics

Open Out & In

General Size Limitations are shown on Page A02.

For Wind Loading Limitations, Please Contact

The Technical Department - T: 01934 833100

PAGE D01
 MC600

THIS PAGE IS INTENTIONALLY LEFT BLANK

PAGE D02
 MC 600
Statics

Statics

Important Note

The selection of suitable mullions and transoms should be based on the design
wind load of the structure based on criteria including location; exposure;
average wind speeds etc. The following pages will assist with the selection of
suitable mullions and transoms. For specific details regarding wind loading
limitations or further advice, please contact our Technical Department.

Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE D 03

 MC 600
Statics

MC612 Technical Specification

MC612
Scale 1:1

= Fixing Bracket

H H = Unsupported Span

L = Transom Centres
4
IX(cm ) = 23.54

H (mm) MC612 MC613

4000
3750

3500

3250

3000
2750

2500

2250

2000
Design
1750 Wind
Load
1500 750 Pa
1000 Pa
1250 1250 Pa
1500 Pa
1750 Pa
2000 Pa

500 1000 1500 2000 2500

L (mm)

Do Not Scale From This Drawing

PAGE D 04 ISSUED: JANUARY 2021

 MC 600
Statics

MC614 Technical Specification

MC614
Scale 1:2
= Fixing Bracket

H H = Unsupported Span
IX(cm4) = 120.61
L = Transom Centres

H (mm) MC614
6000
5750

5500

5250

5000
4750

4500

4250

4000
3750

3500

3250

3000 Design
Wind
2750 Load
750 Pa
2500
1000 Pa
2250 1250 Pa
1500 Pa
2000 1750 Pa
2000 Pa
1750

1500

1250

500 1000 1500 2000 2500

L (mm)

Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE D 05

 MC 600
Statics

MC615 Technical Specification

MC615
Scale 1:2
= Fixing Bracket

H H = Unsupported Span
IX(cm4) = 116.94
L = Transom Centres

H (mm) MU615

6000
5750

5500

5250

5000
4750

4500

4250

4000
3750

3500

3250
Design
3000
Wind
2750 Load
750 Pa
2500
1000 Pa
2250 1250 Pa
1500 Pa
2000 1750 Pa
2000 Pa
1750

1500

1250

500 1000 1500 2000 2500

L (mm)

Do Not Scale From This Drawing

PAGE D 06 ISSUED: JANUARY 2021

 MC 600
Statics

MC616 Technical Specification

MC616
Scale 1:2
= Fixing Bracket

H H = Unsupported Span
IX(cm4) = 249.97
L = Transom Centres

H (mm) MC616

7000
6750

6500

6250

6000
5750

5500

5250

5000
4750

4500

4250

4000
3750
Design
3500 Wind
Load
3250 750 Pa

3000 1000 Pa

2750 1250 Pa
1500 Pa
2500 1750 Pa
2000 Pa
2250

500 1000 1500 2000 2500

L (mm)

Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE D 07

 MC 600
Statics

MC617 Technical Specification

MC617
Scale 1:2
= Fixing Bracket

H H = Unsupported Span
IX(cm4) = 232.25
L = Transom Centres

H (mm) MC617

7000
6750

6500

6250

6000
5750

5500

5250

5000
4750

4500

4250

4000
3750
Design
3500 Wind
Load
3250
750 Pa
3000
1000 Pa
2750
1250 Pa

2500 1500 Pa
1750 Pa
2000 Pa
2250

500 1000 1500 2000 2500

L (mm)

Do Not Scale From This Drawing

PAGE D 08 ISSUED: JANUARY 2021

 MC 600
Statics

MC618 Technical Specification

MC618
Scale 1:2
= Fixing Bracket

H H = Unsupported Span
IX(cm4) = 380.41
L = Transom Centres

H (mm) MC618

7000
6750

6500

6250

6000
5750

5500

5250

5000
4750

4500

4250 Design
Wind
4000 Load
3750 750 Pa

3500
1000 Pa
3250
1250 Pa

3000 1500 Pa
1750 Pa
2750 2000 Pa

2500

2250

500 1000 1500 2000 2500

L (mm)

Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE D 09

 MC 600
Statics

MC619 Technical Specification

MC619
Scale 1:2
= Fixing Bracket

H H = Unsupported Span
IX(cm4) = 575.04
L = Transom Centres

H (mm) MC619

7000
6750

6500

6250

6000
5750

5500

5250

5000
4750
Design
4500 Wind
Load
4250 750 Pa

4000
1000 Pa
3750
1250 Pa
3500
1500 Pa

3250 1750 Pa
2000 Pa

500 1000 1500 2000 2500

L (mm)

Do Not Scale From This Drawing

PAGE D 10 ISSUED: JANUARY 2021

 MC 600
Statics

MC620 Technical Specification

MC620
Scale 1:2

IX(cm4) = 1453.17

= Fixing Bracket

H = Unsupported Span

L = Transom Centres

H (mm) MC620

7000
6750

6500

6250
Design
6000 Wind
5750 Load
750 Pa
5500

5250
1000 Pa
5000
1250 Pa
4750

4500 1500 Pa

1750 Pa
4250
2000 Pa
4000
3750

3500

3250

500 1000 1500 2000 2500

L (mm)

Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE D 11

 MC 600
Statics

THIS PAGE IS INTENTIONALLY LEFT BLANK

PAGE D 12 ISSUED: JANUARY 2021

 MC600

Section E

E MC Construction Drawings - Open Out

NHBC Notice....................................................................................... E03

Bracket Requirements......................................................................... E04
Horizontal Deductions......................................................................... E05
Stick Build Mullion Preparation - ACMC650........................................ E06
Stick Build Transom Preparation......................................................... E07
Stick Build Assembly - ACMC650 Spring Pin...................................... E08 - E09
Ladder Build Assembly - Shear Block................................................. E10
Drainage & Pressure Equalisation....................................................... E11
Reinforcing Sleeves............................................................................. E12
Splice Joints........................................................................................ E13
Transom / Mullion Sealing.................................................................. E14
Sleeves................................................................................................ E15
Mullion on Transom Preparation......................................................... E16
Mullion on Transom Assembly............................................................ E17
Raked Head......................................................................................... E18
Glazing Details.................................................................................... E19

ISSUED: JANUARY 2021 PAGE E01

 MC600

THIS PAGE IS INTENTIONALLY LEFT BLANK

PAGE E02 ISSUED: JANUARY 2021

 MC600
CONSTRUCTION DRAWINGS - OPEN OUT

NHBC

Before undertaking any Curtain Wall job, please refer to:

NHBC - Curtain Walling & Cladding - Chapter 6.9

Please note both CWCT and NHBC consider all storey height glazing to be a curtain wall and therefore should be designed as such.
Curtain walling cannot be treated in the same way as window and door installations.

The following are requirements in undertaking a Curtain Walling project:

· Full elevation drawings must be produced. These drawings should clearly indicate all perimeter interface details typically showing
water / vapour barriers, pressings / trims, fixing brackets / fixings along with any fire stopping that may be required. This is not an
exhaustive list as other details may be required to suit specific projects.

· All bracketry and fixings should be backed up by calculations from a structural engineer to confirm suitability and meet site
requirements. Also, profiles need to be identified to suit site conditions. These factors include screen sizes, fixing positions, glass
weight, barrier loadings & wind loadings.

· It may be a requirement to include for on-site water testing and pull out testing. NHBC would require certification to the CWCT
weather test where glazing may span a floor as opposed to a BS6375-1 window / door weather test.

Please also consider acoustic, thermal and structural performance when specifying curtain wall configuration and components.

It would be expected that one or more members of installation teams have been certified by the Systems supplier to demonstrate
competence and understanding of the system being installed.

IF IN DOUBT - CONTACT TECHNICAL DEPARTMENT:

01934 876 100

stechnical@[Link]

The latest NHBC documentation can be found at:

[Link]

Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE E03

 MC600
CONSTRUCTION DRAWINGS - OPEN OUT

Bracket Requirments

Structural Curtain Wall Brackets Single Span Multiple Tie Back Multiple Span
Brackets form the link between the curtain wall and the For single span there are two possible Where mullions span more than one Where mullions span more than one
structure. These are critically important to the safety and arrangements of these fixings for a single storey, restraint fixings are usually mullion length (typically 7m). A Splice
serviceability of the wall. storey mullion. The top hung provided at intermediate floors. By Joint will be required to join mullions.
arrangement is more common but the providing mid point tie back restraints the Each length will require one support
Brackets need to be designed to transfer all the loads from the bottom supported arrangement may be required mullion strength may be fixing for dead load transfer.
curtain wall to the structure safely, whilst accommodate tolerances used, particularly for low rise reduced.
and movement. The screen will depend on the availability of a construction.
suitable support structure (tie back positions).
Support
The loads will vary on the size of the screen and the location of the
building. Brackets need to be designed to interface with a suitable
support structure/building frame. Detail drawings will be required to Restraint
identify the location and position of any brackets.

Dead loads - Support

The weight of the curtain wall needs to be transferred to the
structure.

Live Loads - Restraint Support

Wind loads in the form of negative (suction) or positive pressures Top Hung
are usually the dominant load case. Support

Brackets and fixings on curtain wall are structural and must be

designed to relevant structural codes. Restraint
Restraint Restraint
BS8118. Structural Use of Aluminium
Support

Restraint
(Intermediate Tie Back)

Typical Load Requirements

Restraint
FFL First Floor (Intermediate Tie Back)

Head Bracket/Fixing Requirements

Support + Restraint
Restraint Restraint Restraint
Dead Load 1.5 kN
Live Load 3.0kN Restraint

Bottom
Support
FFL Ground Floor

Based on a 5m high mullion

at 1m centres.
Glass Weight 30kg/m Base Bracket/Fixing Requirements
Wind Load 1200Pa Restraint only
Live Load 3.0kN

Do Not Scale From This Drawing

PAGE E04 ISSUED: JANUARY 2021

 MC600
CONSTRUCTION DRAWINGS - OPEN OUT

Horizontal Deductions
W
28.5 28.5
27.5 27.5
TRANSOM TRANSOM

Horizontal Deductions
Component Formula

Glass W - 25
Capping W - 56

Pressure Plate W - 58
Transom
without End Pads
W - 55
Transom
with End Pads
W - 57
Isolator
without Transom End Pads
W - 55

B
END PAD END PAD
Isolator
with Transom End Pads
W - 57

Gasket W - 255

GASKET GASKET

100
100

PRESSURE PLATE PRESSURE PLATE

CAPPING CAPPING

12.5 12.5
28 28
29 29

Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE E05

 MC600
CONSTRUCTION DRAWINGS - OPEN OUT

Stick Build Mullion Preparation - ACMC650

ACMC695 - Drill Jig

55 54.5 MC612 MC603 MC614 MC616 MC618 MC619
27.5 27.5

Ø Ø4
4
Ø4

Ø1
Ø1
Ø1

Ø1
Ø1
Ø
11

1
1
1

1
1
20
68

4 Ø
Ø 4 Ø4

47
40 31.5
Align drill jig over 78.5
centre line and 102
clamp in position
128.5

151
10

177
195
ACMC650

27.5
Ø5

Ø5
Ø5

Ø5
Ø5

Ø5
Drill with a Ø5mm bit
using ACMC695 drill jig
and open to Ø11mm
MC612 MC603 MC614 MC616 MC618 MC619

27.5
217
ACMC695 - Drill Jig

Do Not Scale From This Drawing

PAGE E06 ISSUED: JANUARY 2021

 MC600
CONSTRUCTION DRAWINGS - OPEN OUT

Stick Build Transom Preparation

IMPORTANT NOTE:
Drill through ACMC691 Maximum load on ACMC600 /
using 3mm drill bit. Once ACMC605 = 500kg
ACMC691 is removed, open
holes to 4mm.
Mullion

Fix ACMC600 / ACMC605

into Transom using 2 x
ACET060 & Mullion using
2 x PUA028
Only 2 marked holes
should be drilled for
ACMC600 & ACMC605 2 x PUA028
2 x ACET060

Transom ACMC600
or
ACMC605

ACMC691 should be butted

up to end of transom and
then locked in place using
Transom
thumb screw.
ACMC691
Transom Drill Jig

Isolator
Transom Brackets
Slide & Fix ACMC600 /
ACMC605 onto transom
Transom Block Isolator Glazing Thickness before placing on mullion Isolator
ACMC600 MC601 6mm - 32mm

ACMC605 MC602 34mm - 42mm

Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE E07

 MC600
CONSTRUCTION DRAWINGS - OPEN OUT

Stick Build Assembly - ACMC650 Spring Pin

ll ion
Mu

601
MC

Ensure hole is de-burred

and clear of any debris.

Apply ACSIL05 gasket rubber sealant to

transom end pad close to the edges

Apply ACSIL05 gasket rubber

sealant to transom bracket
AC
MC prior to fitting rubber cap
650

Mu
llio
n

Clean any excess sealant

ad
dp
en
om
ns
Tra

Tra
600 ns
CMC om
A
Tra
ns
om
MC
6 01

Do Not Scale From This Drawing

PAGE E08 ISSUED: JANUARY 2021

 MC600
CONSTRUCTION DRAWINGS - OPEN OUT

Ladder Build Assembly - Shear Blocks

Mullion

Always drill this hole

ACMC692 Transom
ACMC692
see table
Mullion
C 2 x ACET060
B
A

60 60 607
M MC MC
A AC

3 2
C
C
C
A
Apply ACSIL05 gasket rubber
sealant to faces of ACMC604 that
make contact with Transom,
2 x PUA028
Mullion and Isolator

ACMC604

Shear Block

Ladder Frame Assembly

Drill through ACMC691

using 3mm drill bit. Once Transom Drill Location Shear Block
ACMC691 is removed, open
holes to 4mm.
MC604 C ACMC602
Only 2 marked holes
should be drilled for
Shear Blocks MC614 B ACMC603

MC617 A ACMC607

Transom
Remove excess
ACMC691
ACSIL05

ACMC691 should be butted up to

end of transom and then locked in
place using thumb screw.

ISSUED: JANUARY 2021 PAGE E09

 MC600
CONSTRUCTION DRAWINGS - OPEN OUT

Ladder Build Assembly - Shear Blocks

For preparation of MC650/MC651, clamp profiles MC

615
together and use ACMC692 drill jig.

M
C
65
0
MC
615

650
MC

MC
615

4N
tap

O
.P
pin

U
gs

A
02
cre

8
Se
ws

l f
.

MC
650
MC
615
6 50
MC

or...
MC
650
Machine back plate individually using
dimensions shown.

MC
650

ACMC692 -
75 Shear Block Drill Jig

Do Not Scale From This Drawing

PAGE E10 ISSUED: JANUARY 2021

 MC600
CONSTRUCTION DRAWINGS - OPEN OUT

Drainage & Pressure Equalisation

Punched hole
for fixing
DK154

25

5 25

5
25

10
25* 75
25mm x 10mm Notch is
125
only required when
*Maximum distance on
using DK052
fixing holes from end of 175
pressure plate = 80mm
250

MC652

IMPORTANT NOTE: Place additional slot at End

To prevent noise and air permeability (which may Cap centre if length is over
carry moisture), it is good practice to adjust the slot
1800mm
position to ensure the slot in cover cap is not aligned
with the drainage slot in the Pressure Plate.

25 25

50 Nom.
from each end
5
℄
Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE E11

 MC600
CONSTRUCTION DRAWINGS - OPEN OUT

Reinforcing Sleeves

1000mm Sleeve

IMPORTANT NOTE:
Use suitable fixings to support
structural strength of box

CLEARANCE HOLE
ANTI-CRUSH SPACER
CLEARANCE HOLE
FOR BOLT ONLY

Mullion
1000mm
ANTI-CRUSH SPACER
Sleeve

NUT
BOLT

eve
Sle WASHER
0mm WASHER
100
300 min

Temporarily insert
2 x ACET060 to work
as stops for sleeve
Reinforcing Sleeves
Transom /
Description Sleeve 1000mm Sleeve
Mullion
MC612 50mm Box UTL052 -
Remove 2 x ACET060 once
sleeve is fixed in place MC603 75mm Box MC693 ACMC663
IMPORTANT NOTE:
MC614 100mm Box MC694 ACMC664
Sleeve must insert into mullion by
a minimum of 300mm. MC616 125mm Box MC696 ACMC666

MC618 150mm Box MC698 ACMC668

MC619 170Mmm Box MC699 ACMC669

MC625 90° Corner MC698 ACMC668

Mullion
MC620 225mm Box MC698 ACMC668

Do Not Scale From This Drawing

PAGE E12 ISSUED: JANUARY 2021

 MC600
CONSTRUCTION DRAWINGS - OPEN OUT

Splice Joints
DK053 DK154

ACMC644 80°
MC601 Sleeve Mullion LOW MODULUS
SEALANT
ACMC644
*
AC
S IL
04

10
AC
MC
644

50
AC

10
SIL
04

300 minimum
LOW MODULUS
SEALANT

Bracket by others
10

* Ensure that glue holes on ACMC644 are above the splice joint.
50

ACMC644

MC050 ACMC040
10
100
50
150

10

ACMC040 joint strap can

be used with MC050 cap
ACET060
only
Position screw to prevent sleeve from
dropping during installation.
10

Remove once complete.

All brackets & fixings must be specified

by a structural engineer

Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE E13

 MC600
CONSTRUCTION DRAWINGS - OPEN OUT

Transom / Mullion Sealing

ACSIL05 around perimeter of cut edge of

transom before fitting end pad

AC
S IL
05

ACSIL05 on top face of ACMC600 Clean excess ACSIL05 from

cast metal component transom / mullion joint

AC
SI
Ensure to ACSIL05 end pad

L0
5
contact points

ACSIL05 around perimeter of end pad AC

SI
L0
5
AC ACSIL05 on internal surfaces of
SIL ACMC600 rubber component
05
where in contact with isolator

Do Not Scale From This Drawing

PAGE E14 ISSUED: JANUARY 2021

 MC600
CONSTRUCTION DRAWINGS - OPEN OUT

Sleeves

MC693
38

MC694
64.5
MC696

87
75.5
MC698

113
11

99.5

131
18.5

99.5
11
37.5

MC699
18.5

11
37.5

18.5

11
37.5
IMPORTANT NOTE:
Flat Plate to be specified by a
Structural Engineer. It should be 18.5
cut and prepared to suit aperture.
37.5

18.5

37.5

Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE E15

 MC600
CONSTRUCTION DRAWINGS - OPEN OUT

Mullion on Transom Preparation

110.5
50
℄ 7.5
25

12.5

Gable end shown as example

Transom Transom
END View FRONT View

℄ ℄
Shear Block X (mm) Y (mm)

X
ACMC6052 30 - Y

ACMC6053 53.5 23.5

36 Y ACMC6054 80 50

ACMC6056 102.5 72.5

ACMC6058 128 98

ACMC6059 146.5 116.5

Transom

MC603 MC612 MC614 MC616 MC618 MC619 MC621

℄ MC603 ACMC6053 ACMC6053 ACMC6053 ACMC6053 ACMC6053 ACMC6053

Ø3 MC612 ACMC6052 ACMC6052 ACMC6052 ACMC6052 ACMC6052 ACMC6052 ACMC6052

Mullion
MC614 ACMC6054 ACMC6054 ACMC6054 ACMC6054 ACMC6054

Transom
MC616 ACMC6056 ACMC6056 ACMC6056
TOP View
MC618 ACMC6058 ACMC6058

MC619 ACMC6059

Do Not Scale From This Drawing

PAGE E16 ISSUED: JANUARY 2021

 MC600
CONSTRUCTION DRAWINGS - OPEN OUT

Mullion on Transom Assembly

2 x PUA028

℄
7.5

50

2 x PUA028

Mullion Consider fixing detail of

mullion at head for support

Ø4 IMPORTANT NOTE:
Please ensure curtain walling
configuration meets all site requirements
i.e Wind Loads, Structural requirements
22

Transom
Consider packing location
of Glass units.

Do Not Scale From This Drawing

ISSUED: JANUARY 2021 PAGE E17

 MC600
CONSTRUCTION DRAWINGS - OPEN OUT

Raked Head

Use appropriate ACMC605* Shear

Shear Block
Block and Transom cut at desired
angle for fixing locations

°
- 90
°
35

2 x PUA028
2 x PUA028

36 Y Shear Block

2 x PUA028

ACMC693 AC
Ø4 SIL
05

ACMC646
or
ACMC647

Shear Block X (mm) Y (mm)

Transom
ACMC6052 30 -
X
Y

ACMC6053 53.5 23.5

Drill Ø4mm through
ACMC6054 80 50 bushes for 2 x PUA028

ACMC6056 102.5 72.5

ACMC6058 128 98

ACMC6059 146.5 116.5

Do Not Scale From This Drawing

PAGE E18 ISSUED: JANUARY 2021

 MC600
CONSTRUCTION DRAWINGS - OPEN OUT

Glazing Details

43.5
Internal Gasket Corner Gasket Glazing Support Isolator Screw Transom Bracket
GLAZING EXAMPLE 6

6** ACSC212 ACMC624 ACMC630 MC601 ACMC610 ACMC600

ACSC212
10** ACSC208 ACMC632 ACMC630 MC601 ACMC610 ACMC600
MC118
14* ACMC115 ACMC624 ACMC630 MC601 ACMC610 ACMC600
ACMC630
Glazing Thickness (mm)

24 ACMC115 ACMC624 ACMC630 MC601 ACMC610 ACMC600

15
28 ACSC212 ACMC628 ACMC630 MC601 ACMC610 ACMC600

32 ACSC208 ACMC632 ACMC630 MC601 ACMC610 ACMC600

34 ACMC115 ACMC624 ACMC631 MC602 ACMC612 ACMC605

38 ACSC212 ACMC628 ACMC631 MC602 ACMC612 ACMC605

15
42 ACSC208 ACMC632 ACMC631 MC602 ACMC612 ACMC605

*1 x MC116 required MC601

**1 x MC118 required ACSC212
DK154

4.50
28

ACMC601 or ACMC605

Type B IMPORTANT NOTE:

ACDK066 is to be used with DK154 only
Type A

Use ACSIL05 Gasket

Type A DK154 7.5 MC655 7.5
Sealant to join corner
gasket to standard gasket Type B

ACDK066

ISSUED: JANUARY 2021 PAGE E19

 MC600
CONSTRUCTION DRAWINGS - OPEN OUT

THIS PAGE IS INTENTIONALLY LEFT BLANK

Do Not Scale From This Drawing

PAGE E20 ISSUED: JANUARY 2021