Super Precision.

FIN 1/10/07 3:55 PM Page 2

Table of Contents
Super Precision Machine Tool Bearings

INTRODUCTION
About NSK Super Precision
Machine Tool Bearings . . . . . . . . . . . . . . . . .183
NOMENCLATURE/INTERCHANGE
Super Precision Angular Contact . . . . . . . . .184
Super Precision Cylindrical Roller . . . . . . . .186
Angular Contact Thrust Ball Bearings . . . . . .187
Ball Screw Support Bearings . . . . . . . . . . . .188
APPLICATION
Super Precision Angular Contact . . . . . . . . .189
Super Precision Cylindrical Roller . . . . . . . .189
Ball Screw Support Bearings . . . . . . . . . . . .189
BEARING TABLES
7000C Series . . . . . . . . . . . . . . . . . . . . . . . .190
7000A5 Series . . . . . . . . . . . . . . . . . . . . . . .192
7200C Series . . . . . . . . . . . . . . . . . . . . . . . .194
7200A5 Series . . . . . . . . . . . . . . . . . . . . . . .196
7900C Series . . . . . . . . . . . . . . . . . . . . . . . .198
7900A5 Series . . . . . . . . . . . . . . . . . . . . . . .200
*BNC Series . . . . . . . . . . . . . . . . . . . . . . . .202
BNR Series . . . . . . . . . . . . . . . . . . . . . . . . .206
BGR Series . . . . . . . . . . . . . . . . . . . . . . . . .210
BAR/BTR Series . . . . . . . . . . . . . . . . . . . . . .214
N1000 Series . . . . . . . . . . . . . . . . . . . . . . . .218
NN3000 Series . . . . . . . . . . . . . . . . . . . . . .220
NN3900 Series . . . . . . . . . . . . . . . . . . . . . .222
Ball Screw Support Bearings . . . . . . . . . . . .224
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227

*BNR has replaced BNC Series.

Contact NSK Engineering for details

182
Super [Link] 1/10/07 3:55 PM Page 3

Introduction

ABOUT NSK SUPER PRECISION BEARINGS

■ Super Precision Angular Contact Bearings
■ High Speed Super Precision Angular Contact Bearings
■ Super Precision Angular Contact Thrust Bearings
■ Super Precision Cylindrical Roller Bearings
■ Ball Screw Support Bearings

NSK has developed new methods of manufacturing to produce several series of bearings that
meet the ever-increasing needs for higher speeds and greater precision in bearing applications. These
Super Precision Bearings include angular contact bearings, precision cylindrical roller bearings and ball
screw support bearings.
Super Precision Angular Contact bearings are specifically designed for rigid, high-speed, high-
precision machine tool spindles. Their state-of-the-art preload control assures consistent high
performance. Super Precision Angular contacts are also available with seals – contact NSK for
details.
High Speed Super Precision Angular Contact bearings are now available due to NSK’s new optimized
design, under the ROBUST name. Allowing increased speeds and improved performance, these series
are available in application specific designs for machining center applications (BNR), and high speed
grinding applications (BGR) – both allowing customers to push the limits of existing speeds.
Super Precision Angular Contact Thrust bearings are designed to work together with high speed
super precision cylindrical roller bearings where high speed, and high rigidity are required. Offered in
a 30º and 40º series, this offering allows flexibility for meeting the rigidity requirements seen in many
machine tool applications.
Super Precision Cylindrical roller bearings are designed to specifically handle large radial loads in
high speed applications. They are available in a variety of designs, including double row and single row
options, to suit various applications. In addition, a standard lube groove and hole feature is available
along with tapered and non-tapered bores. When combined with Super Precision Angular Contact Thrust
bearings, the Super Precision Cylindrical meets the high rigidity requirements of many machine tool
spindle applications.
Ball Screw Support bearings are designed specifically to provide maximum axial rigidity and improved
feeding accuracy for use with precision ball screws. They are high accuracy angular contact thrust
bearings, which are superior to combinations of standard angular contact bearings or arrangements of
radial and thrust bearings for ball screw applications. Both Metric and Inch series are available.
Ball Screw Support Units are also available from NSK. Please reference, Linear Section, p. 270, for
more details.

183
Super [Link] 1/10/07 3:55 PM Page 4

Nomenclature — Super Precision Angular Contact

Interchange — High Precision Angular Contact

INTERCHANGE
DESCRIPTION
NSK *OLD NSK SKF FAG BARDEN OLD BARDEN FAFNIR SNFA NTN
ULTRA LIGHT SERIES 79XX 79XX 719XX 719XX 19XX - 93XXWI B 79XX
Part No.

EXTRA LIGHT SERIES 70XX 70XX 70XX 70XX 1XX 1XX 91XXWI X 70XX
LIGHT SERIES 72XX 72XX 72XX 72XX 2XX 2XX 2XXWI 2 72XX
15˚ CONTACT ANGLE C C CD C C BLANK 2* 1 C
25˚ CONTACT ANGLE A5 A5 ACD E E 2* 3* 3 -
POLYAMIDE CAGE TYN TY - - TMT - PRC P T2
PHENOLIC CAGE TR T BLANK T TA BLANK CR C T1
SEALS V1V - S* 2RSD OR RR - /S -
S PREFIX
DUPLEX UNIVERSAL DU DU DG DU DU D DU DU GD2
Part Number Suffix

SINGLE UNIVERSAL SU SU G U U - SU U G
EXTRA LIGHT PRELOAD EL EL - - - - X - GL
LIGHT PRELOAD L L A L L L L L GN
MEDIUM PRELOAD M M B M M M M M GM
HEAVY PRELOAD H H C H H H H H GH
CERAMIC BALLS SN24 SN24 HC HCB* C* - C* /NS 5S*
ABEC 7 PRECISION P4Y P4 P4A P4S BLANK BLANK MM* 7 P4
ABEC 9 PRECISION P2 P2 PA9A - ABEC 9 ABEC 9 MMX* 9 P2
*TYN cage replaces TY, TR cage replaces T. Sealed (V1V) versions are a new option and P4Y tolerance specification replaces P4. P4Y tolerance specification have tighter bore and OD
control than ABEC 7 (class 4 or P4) NSK supplies the following bearing series with P4Y tolerance: 7000; 7200;

184
Super [Link] 1/10/07 3:55 PM Page 5

Nomenclature — High Speed Super Precision Angular Contact

Ball Bearings

Interchange — Ultra High Precision Angular Contact

INTERCHANGE
DESCRIPTION
NSK *OLD NSK SKF BARDEN FAFNIR SNFA NTN
ULTRA LIGHT ROBUST HIGH SPEED SERIES XXBNR19 XXBNC19 719XXCE ZSB19XX 93XXWO,WN,HX VEBXX HSB9XX
EXTRA LIGHT ROBUST HIGH SPEED SERIES XXBNR10 XXBNC10 70XXCE ZSB1XX 91XXWO,WN,HX VEXXX HSB0XX
Part No.

ULTRA LIGHT ROBUST HIGH SPEED SERIES

FOR GRINDING SPINDLES XXBGR19 XXBNT19 - - - - BNT9XX
EXTRA LIGHT ROBUST HIGH SPEED SERIES
FOR GRINDING SPINDLES XXBGR10 XXBNT10 - XXBX48 - - BNT0XX
POLYAMIDE CAGE TYN TY BLANK TMT PRC P -
PHENOLIC CAGE TR T - T CR C BLANK
DUPLEX UNIVERSAL DU DU DG DU DU DU D
Part Number Suffix

SINGLE UNIVERSAL SU SU G U SU U BLANK

EXTRA LIGHT PRELOAD EL EL - - X - GL
LIGHT PRELOAD L L A L L L GN
CERAMIC BALLS H SN24 HC C* C* /NS 5S*
STEEL BALLS S BLANK BLANK BLANK BLANK BLANK BLANK
ABEC 7 PRECISION P4Y P4 P4 BLANK MMV* 7 P4
ABEC 9 PRECISION P2 P2 P2 ABEC 9 MMX* 9 P2
*BNR has replaced BNC series. P4Y tolerance specification replaces P4. P4Y tolerance specification have tighter bore and OD control than ABEC 7 (class 4 or P4) NSK supplies the
following bearing series with P4Y tolerance: 7000; 7200; 7900; and BNR.

185
Super [Link] 1/10/07 3:55 PM Page 6

Nomenclature — Super Precision Cylindrical Roller Bearings

Double Row — Super Precision Cylindrical Roller Bearings

Single Row — Super Precision Cylindrical Roller Bearings

Interchange — Precision Cylindrical Roller Bearings

INTERCHANGE
DESCRIPTION
NSK *OLD NSK SKF FAG NTN
ULTRA LIGHT DOUBLE
ROW CYLINDRICAL SERIES NN39XX NN39XX - - -
Part No.

EXTRA LIGHT DOUBLE

ROW CYLINDRICAL SERIES NN30XX NN30XX NN30XX NN30XX NN30XX
EXTRA LIGHT SINGLE
ROW CYLINDRICAL SERIES N10XX N10XX N10XX N10XX N10XX
NON-METALLIC CAGE TB T TN,TN9 - -
BRASS CAGE MB M BLANK M G1
Part Number Suffix

TAPERED BORE KR K UPK K K

LUBE GROOVE AND HOLES
ON OUTER RING E44 - W33 S -
MATCHED CLEARANCE,
RINGS NOT TO BE MIXED CCX CCX CX CX CXNA
ABEC 7 PRECISION P4 P4 SP SP P4
*The outer ring machined lubrication groove and holes (E44) is now a standard feature. TB cage
replaces T cage, MB replaces M and KR replaces K.

186
Super [Link] 1/10/07 3:55 PM Page 7

Nomenclature — Angular Contact Thrust Ball Bearings

Interchange — Thrust Angular Contact Ball Bearings

INTERCHANGE
DESCRIPTION
NSK *OLD NSK SKF NTN
30˚ ANGULAR CONTACT
THRUST BEARINGS XXBAR10 XXBA10 BTMXXA HTA0XXADB
Part No.

40˚ ANGULAR CONTACT

THRUST BEARINGS XXBTR10 XXBT10 BTMXXB HTA0XXDB
POLYAMIDE CAGE TYN TY BLANK T2
PHENOLIC CAGE TR T - T1
DUPLEX UNIVERSAL DU DU DB GD2
Part Number Suffix

SINGLE UNIVERSAL SU SU - G
EXTRA LIGHT PRELOAD EL EL - -
LIGHT PRELOAD L L A GN
CERAMIC BALLS H SN24 HC 5S*
STEEL BALLS S BLANK BLANK BLANK
ABEC 7 PRECISION P4A P4A P4A P4
ABEC 9 PRECISION P2A P2A PA9A P2
*BAR and BTR series has replaced BA and BT series.

187
Super [Link] 1/10/07 3:55 PM Page 8

Nomenclature — Ball Screw Support Bearings

Interchange — Ball Screw Support Bearings

INTERCHANGE
DESCRIPTION
NSK SKF TORR/FAF MRC NTN
METRIC TYPE xxTACxxx BDAB6342xx MMxxBSxxx -- BSTxxXxx
Part
No.

INCH TYPE xxTACxxx BDAB6342xx MM93xxWI xH Jxxx --

INTERNAL SPECIFICATIONS A -- -- -- X
(Standard Capacity)
INTERNAL SPECIFICATIONS B A -- -- -1
(High Capacity)
SINGLE UNIVERSAL SU -- SU DS BLANK
DUPLEX UNIVERSAL DU DG DU DU --
DUPLEX FACE TO FACE DF DF DU DF DF
DUPLEX BACK TO BACK DB DB DU DB DB
Suffix

DUPLEX TANDEM DT DT DU DT DT
QUAD SET \ \ / / DFF QFC QU -- DTFT
QUAD SET \ / / / DFT QFT QU DFDT --
QUAD SET //\\ DBB QBC QU -- --
QUAD SET / \ \ \ DBT QBT QU -- DTBT
QUAD SET / / / / DTT QT QU -- --
METRIC SERIES PRELOAD C10 BLANK H -- BLANK
INCH SERIES PRELOAD C11 BLANK H BLANK --
CORRESPONDS TO ISO CLASS 4 PN7A P4(PA7) MM BLANK UP
TIGHTER BORE AND O.D. ACCURACY PN7B P4(PA7) MM BLANK UP
FOR SU BEARINGS
The competitive manufacturers are provided for a convenient source of unit substitution. They can be considered interchangeable in most instances,
but for special applications, please consult NSK Engineering. NSK assumes no liability with respect to errors or omissions.

188
Super [Link] 1/10/07 3:55 PM Page 9

Super Precision Machine Tool Bearing Applications

ABOUT NSK SUPER PRECISION MACHINE TOOL BEARINGS

This section covers three types of super precision bearings for use in machine tools. They are super
precision angular contact ball bearings, super precision cylindrical roller bearings and ball screw support
bearings.
The NSK super precision angular contact ball bearing is ideally designed to support the thrusting
conditions in most machine tools while still running at very high speeds. The bearings are readily available
with either 15°or 25° contact angles with either one of the high speed polyamide or phenolic cages.
The NSK super precision cylindrical roller bearing is superior for handling high radial loading conditions
while operating with exceptional accuracy. These bearings are obtainable with flanges on the outer ring or
on the inner.
The NSK ball screw support bearing is ideally suited for the combined radial and axially loading to support
the ball screw. The bearings have a high contact angle for precise positioning of the ball screw, maximum
axial rigidity, and exact control of lateral eccentricity.

SUPER PRECISION ANGULAR CONTACT SUPER PRECISION CYLINDRICAL

■ Machine Tool Spindles on: ■ Machine Tool Spindles for float and high
- Lathes radial loadings.
- Boring Machinery ■ (N, NN) Design for exact positioning of the
- Grinders ball screw in a variety of machine tools.
- Machining Centers
- Milling Machines BALL SCREW SUPPORT BEARINGS
- Slicing Machines
- Drilling Machines ■ Precision Ball Screws
- Gem Cutting Machines

189
Super [Link] 1/10/07 3:55 PM Page 10

Super Precision
Angular Contact
7000C Series
15° Contact Angle

Basic Bearing Dimensions Preferred Shoulder Dimensions

Bearing
d D B da min Damax *Db max ra max *rb max
Number
mm inch mm inch mm inch inch inch inch inch inch
7000 C 10 0.3937 26 1.0236 8 0.3150 0.492 0.925 0.976 0.012 0.006
7001 C 12 0.4724 28 1.1024 8 0.3150 0.571 1.004 1.055 0.012 0.006
7002 C 15 0.5906 32 1.2598 9 0.3543 0.689 1.161 1.213 0.012 0.006
7003 C 17 0.6693 35 1.3780 10 0.3937 0.768 1.280 1.331 0.012 0.006
7004 C 20 0.7874 42 1.6535 12 0.4724 0.984 1.457 1.555 0.024 0.012
7005 C 25 0.9843 47 1.8504 12 0.4724 1.181 1.654 1.752 0.024 0.012

7006 C 30 1.1811 55 2.1654 13 0.5118 1.417 1.929 1.969 0.039 0.020

7007 C 35 1.3780 62 2.4409 14 0.5512 1.614 2.205 2.244 0.039 0.020
7008 C 40 1.5748 68 2.6772 15 0.5906 1.811 2.441 2.480 0.039 0.020
7009 C 45 1.7717 75 2.9528 16 0.6299 2.008 2.717 2.756 0.039 0.020
7010 C 50 1.9685 80 3.1496 16 0.6299 2.205 2.913 2.953 0.039 0.020

7011 C 55 2.1654 90 3.5433 18 0.7087 2.441 3.268 3.346 0.039 0.024

7012 C 60 2.3622 95 3.7402 18 0.7087 2.638 3.465 3.543 0.039 0.024
7013 C 65 2.5591 100 3.9370 18 0.7087 2.835 3.661 3.740 0.039 0.024
7014 C 70 2.7559 110 4.3307 20 0.7874 3.031 4.055 4.134 0.039 0.024
7015 C 75 2.9528 115 4.5276 20 0.7874 3.228 4.252 4.331 0.039 0.024

7016 C 80 3.1496 125 4.9213 22 0.8661 3.425 4.646 4.724 0.039 0.024
7017 C 85 3.3465 130 5.1181 22 0.8661 3.622 4.843 4.921 0.039 0.024
7018 C 90 3.5433 140 5.5118 24 0.9449 3.898 5.157 5.276 0.059 0.031
7019 C 95 3.7402 145 5.7087 24 0.9449 4.094 5.354 5.472 0.059 0.031
7020 C 100 3.9370 150 5.9055 24 0.9449 4.291 5.551 5.669 0.059 0.031

7021 C 105 4.1339 160 6.2992 26 1.0236 4.528 5.906 6.063 0.079 0.039
7022 C 110 4.3307 170 6.6929 28 1.1024 4.724 6.299 6.457 0.079 0.039
7024 C 120 4.7244 180 7.0866 28 1.1024 5.118 6.693 6.850 0.079 0.039
7026 C 130 5.1181 200 7.8740 33 1.2992 5.512 7.480 7.638 0.079 0.039
7028 C 140 5.5118 210 8.2677 33 1.2992 5.906 7.874 8.031 0.079 0.039
7030 C 150 5.9055 225 8.8583 35 1.3780 6.378 8.386 8.583 0.079 0.039

7032 C 160 6.2992 240 9.4488 38 1.4961 6.772 8.976 9.173 0.079 0.039
7034 C 170 6.6929 260 10.2362 42 1.6535 7.165 9.764 9.961 0.079 0.039
7036 C 180 7.0866 280 11.0236 46 1.8110 7.559 10.551 10.748 0.079 0.039
7038 C 190 7.4803 290 11.4173 46 1.8110 7.953 10.945 11.142 0.079 0.039
7040 C 200 7.8740 310 12.2047 51 2.0079 8.346 11.732 11.929 0.079 0.039
*Db is housing diameter for low shoulder. rb is housing fillet radius for low shoulder.

Application Data
Bearing Tolerances –– Table 10.12 thru Table 10.16 on page 314-17
Preload –– Table 10.46 on page 337
Shaft & Housing Fits –– Contact NSK engineering

190
Super [Link] 1/10/07 3:55 PM Page 11

Common Options
TR : Phenolic cage
TYN : Polyamide cage
DU : Duplex Universal
SU : Single Universal
L : Light Preload
M : Medium Preload
H : Heavy Preload
P4 : ISO 4 (ABEC 7) Precision
P5 : ISO 5 (ABEC 5) Precision

Bearing
Basic Load Ratings Limiting Speeds Weight
Bearing (lbs) (1000 RPM) (Approx.)
Number
Cr Cor Grease Oil lbs
7000 C 1190 560 63.9 97.3 0.05
7001 C 1300 650 57.5 87.5 0.05
7002 C 1400 760 49 74.5 0.07
7003 C 1490 860 44.3 67.4 0.10
7004 C 2490 1470 37.1 56.5 0.17
7005 C 2620 1660 32 48.7 0.19

7006 C 3400 2310 27.1 41.2 0.29

7007 C 4300 3060 23.8 36.1 0.37
7008 C 4630 3570 21.3 32.5 0.46
7009 C 5490 4320 19.2 29.2 0.59
7010 C 5840 4920 17.7 27 0.64

7011 C 7720 6440 15.9 24.2 0.93

7012 C 7940 6940 14.9 22.6 0.99
7013 C 8380 7720 14 21.3 1.06
7014 C 10600 9700 12.8 19.5 1.49
7015 C 10800 10300 12.2 18.5 1.62

7016 C 13200 12500 11.3 17.1 2.11

7017 C 13600 13200 10.7 16.3 2.21
7018 C 16100 15500 10 15.3 2.91
7019 C 16500 16400 9.6 14.6 3.06
7020 C 17000 17400 9.2 14 3.18

7021 C 19800 20100 8.7 13.3 3.97

7022 C 23800 23400 8.3 12.5 4.94
7024 C 25100 26200 7.7 11.7 5.31
7026 C 29100 30900 7 10.7 8.03
7028 C 29800 32600 6.6 10 8.49
7030 C 34000 37900 6.2 9.4 10.30

7032 C 38400 43400 5.8 8.8 12.55

7034 C 46100 52700 5.4 8.2 17.20
7036 C 51400 61900 5 7.7 22.49
7038 C 55300 69400 4.8 7.3 24.48
7040 C 59500 76100 4.6 6.9 29.77
Cr = Dynamic Radial Load Rating
Cor = Static Radial Load Rating

191
Super [Link] 1/10/07 3:55 PM Page 12

Super Precision
Angular Contact
7000A5 Series
25° Contact Angle

Basic Bearing Dimensions Preferred Shoulder Dimensions

Bearing
d D B da min Damax *Db max ra max *rb max
Number
mm inch mm inch mm inch inch inch inch inch inch
7000 A5 10 0.3937 26 1.0236 8 0.3150 0.492 0.925 0.976 0.012 0.006
7001 A5 12 0.4724 28 1.1024 8 0.3150 0.571 1.004 1.055 0.012 0.006
7002 A5 15 0.5906 32 1.2598 9 0.3543 0.689 1.161 1.213 0.012 0.006
7003 A5 17 0.6693 35 1.3780 10 0.3937 0.768 1.280 1.331 0.012 0.006
7004 A5 20 0.7874 42 1.6535 12 0.4724 0.984 1.457 1.555 0.024 0.012
7005 A5 25 0.9843 47 1.8504 12 0.4724 1.181 1.654 1.752 0.024 0.012

7006 A5 30 1.1811 55 2.1654 13 0.5118 1.417 1.929 1.969 0.039 0.020

7007 A5 35 1.3780 62 2.4409 14 0.5512 1.614 2.205 2.244 0.039 0.020
7008 A5 40 1.5748 68 2.6772 15 0.5906 1.811 2.441 2.480 0.039 0.020
7009 A5 45 1.7717 75 2.9528 16 0.6299 2.008 2.717 2.756 0.039 0.020
7010 A5 50 1.9685 80 3.1496 16 0.6299 2.205 2.913 2.953 0.039 0.020

7011 A5 55 2.1654 90 3.5433 18 0.7087 2.441 3.268 3.346 0.039 0.024

7012 A5 60 2.3622 95 3.7402 18 0.7087 2.638 3.465 3.543 0.039 0.024
7013 A5 65 2.5591 100 3.9370 18 0.7087 2.835 3.661 3.740 0.039 0.024
7014 A5 70 2.7559 110 4.3307 20 0.7874 3.031 4.055 4.134 0.039 0.024
7015 A5 75 2.9528 115 4.5276 20 0.7874 3.228 4.252 4.331 0.039 0.024

7016 A5 80 3.1496 125 4.9213 22 0.8661 3.425 4.646 4.724 0.039 0.024
7017 A5 85 3.3465 130 5.1181 22 0.8661 3.622 4.843 4.921 0.039 0.024
7018 A5 90 3.5433 140 5.5118 24 0.9449 3.898 5.157 5.276 0.059 0.031
7019 A5 95 3.7402 145 5.7087 24 0.9449 4.094 5.354 5.472 0.059 0.031
7020 A5 100 3.9370 150 5.9055 24 0.9449 4.291 5.551 5.669 0.059 0.031

7021 A5 105 4.1339 160 6.2992 26 1.0236 4.528 5.906 6.063 0.079 0.039
7022 A5 110 4.3307 170 6.6929 28 1.1024 4.724 6.299 6.457 0.079 0.039
7024 A5 120 4.7244 180 7.0866 28 1.1024 5.118 6.693 6.850 0.079 0.039
7026 A5 130 5.1181 200 7.8740 33 1.2992 5.512 7.480 7.638 0.079 0.039
7028 A5 140 5.5118 210 8.2677 33 1.2992 5.906 7.874 8.031 0.079 0.039
7030 A5 150 5.9055 225 8.8583 35 1.3780 6.378 8.386 8.583 0.079 0.039

7032 A5 160 6.2992 240 9.4488 38 1.4961 6.772 8.976 9.173 0.079 0.039
7034 A5 170 6.6929 260 10.2362 42 1.6535 7.165 9.764 9.961 0.079 0.039
7036 A5 180 7.0866 280 11.0236 46 1.8110 7.559 10.551 10.748 0.079 0.039
7038 A5 190 7.4803 290 11.4173 46 1.8110 7.953 10.945 11.142 0.079 0.039
7040 A5 200 7.8740 310 12.2047 51 2.0079 8.346 11.732 11.929 0.079 0.012
*Db is housing diameter for low shoulder. rb is housing fillet radius for low shoulder.

Application Data
Bearing Tolerances –– Table 10.12 thru Table 10.16 on page 314-17
Preload –– Table 10.46 on page 337
Shaft & Housing Fits –– Contact NSK engineering

192
Super [Link] 1/10/07 3:55 PM Page 13

Common Options
TR : Phenolic cage
TYN : Polyamide cage
DU : Duplex Universal
SU : Single Universal
L : Light Preload
M : Medium Preload
H : Heavy Preload
P4 : ISO 4 (ABEC 7) Precision
P5 : ISO 5 (ABEC 5) Precision

Bearing
Basic Load Ratings Limiting Speeds Weight
Bearing (lbs) (1000 RPM) (Approx.)
Number
Cr Cor Grease Oil lbs
7000 A5 1160 540 55.6 83.4 0.04
7001 A5 1260 630 50 75 0.05
7002 A5 1340 730 42.6 63.9 0.07
7003 A5 1420 820 38.5 57.7 0.09
7004 A5 2380 1410 37.1 56.5 0.15
7005 A5 2510 1600 27.8 41.7 0.17

7006 A5 3240 2190 23.6 35.3 0.25

7007 A5 4080 2930 20.7 31 0.33
7008 A5 4390 3400 18.6 27.8 0.41
7009 A5 5200 4120 16.7 25 0.55
7010 A5 5530 4670 15.4 23.1 0.60

7011 A5 7280 6130 13.8 20.7 0.84

7012 A5 7500 6550 13 19.4 0.90
7013 A5 7940 7280 12.2 18.2 1.00
7014 A5 10000 9150 11.2 16.7 1.38
7015 A5 10300 9700 10.6 15.8 1.44

7016 A5 12500 11800 9.8 14.7 1.94

7017 A5 12800 12500 9.4 14 1.99
7018 A5 15200 14800 8.7 13.1 2.58
7019 A5 15700 15700 8.4 12.5 3.11
7020 A5 16000 16400 8 12 3.20

7021 A5 18700 19100 7.5 11.4 4.01

7022 A5 22500 22300 7.2 10.8 4.98
7024 A5 23800 24900 6.7 10 5.36
7026 A5 27600 29300 6.1 9.1 8.07
7028 A5 28000 30900 5.8 8.6 8.53
7030 A5 32000 35900 5.4 8 10.34

7032 A5 36400 41200 5 7.5 12.59

7034 A5 37500 43400 4.7 7 17.27
7036 A5 41700 51100 4.4 6.6 22.93
7038 A5 45000 56900 4.2 6.3 24.70
7040 A5 48300 63100 4 5.9 30.21
Cr = Dynamic Radial Load Rating
Cor = Static Radial Load Rating

193
Super [Link] 1/10/07 3:55 PM Page 14

Super Precision
Angular Contact
7200C Series
15° Contact Angle

Basic Bearing Dimensions Preferred Shoulder Dimensions

Bearing
d D B da min Damax *Db max ra max *rb max
Number
mm inch mm inch mm inch inch inch inch inch inch
7200 C 10 0.3937 30 1.1811 9 0.3543 0.591 0.984 1.083 0.024 0.012
7201 C 12 0.4724 32 1.2598 10 0.3937 0.669 1.063 1.161 0.024 0.012
7202 C 15 0.5906 35 1.3780 11 0.4331 0.787 1.181 1.280 0.024 0.012
7203 C 17 0.6693 40 1.5748 12 0.4724 0.866 1.378 1.476 0.024 0.020
7204 C 20 0.7874 47 1.8504 14 0.5512 1.024 1.614 1.654 0.039 0.020
7205 C 25 0.9843 52 2.0472 15 0.5906 1.220 1.811 1.850 0.039 0.020

7206 C 30 1.1811 62 2.4409 16 0.6299 1.417 2.205 2.244 0.039 0.024

7207 C 35 1.3780 72 2.8346 17 0.6693 1.654 2.559 2.638 0.039 0.024
7208 C 40 1.5748 80 3.1496 18 0.7087 1.850 2.874 2.953 0.039 0.024
7209 C 45 1.7717 85 3.3465 19 0.7480 2.047 3.071 3.150 0.039 0.024
7210 C 50 1.9685 90 3.5433 20 0.7874 2.244 3.268 3.346 0.039 0.031

7211 C 55 2.1654 100 3.9370 21 0.8268 2.520 3.583 3.701 0.059 0.031
7212 C 60 2.3622 110 4.3307 22 0.8661 2.717 3.976 4.094 0.059 0.031
7213 C 65 2.5591 120 4.7244 23 0.9055 2.913 4.370 4.488 0.059 0.031
7214 C 70 2.7559 125 4.9213 24 0.9449 3.110 4.567 4.685 0.059 0.031
7215 C 75 2.9528 130 5.1181 25 0.9843 3.307 4.764 4.882 0.059 0.031

7216 C 80 3.1496 140 5.5118 26 1.0236 3.543 5.118 5.276 0.079 0.039
7217 C 85 3.3465 150 5.9055 28 1.1024 3.740 5.512 5.669 0.079 0.039
7218 C 90 3.5433 160 6.2992 30 1.1811 3.937 5.906 6.063 0.079 0.039
7219 C 95 3.7402 170 6.6929 32 1.2598 4.213 6.220 6.417 0.079 0.039
7220 C 100 3.9370 180 7.0866 34 1.3386 4.409 6.614 6.811 0.079 0.039

7221 C 105 4.1339 190 7.4803 36 1.4173 4.606 7.008 7.205 0.079 0.039
7222 C 110 4.3307 200 7.8740 38 1.4961 4.803 7.402 7.598 0.079 0.039
7224 C 120 4.7244 215 8.4646 40 1.5748 5.197 7.992 8.189 0.079 0.039
7226 C 130 5.1181 230 9.0551 40 1.5748 5.669 8.504 8.780 0.098 0.039
7228 C 140 5.5118 250 9.8425 42 1.6535 6.063 9.291 9.567 0.098 0.039
7230 C 150 5.9055 270 10.6299 45 1.7717 6.457 10.079 10.354 0.098 0.039

7232 C 160 6.2992 290 11.4173 48 1.8898 6.850 10.866 11.142 0.098 0.039
7234 C 170 6.6929 310 12.2047 52 2.0472 7.402 11.496 11.850 0.118 0.059
7236 C 180 7.0866 320 12.5984 52 2.0472 7.795 11.890 12.244 0.118 0.059
7238 C 190 7.4803 340 13.3858 55 2.1654 8.189 12.677 13.031 0.118 0.059
7240 C 200 7.8740 360 14.1732 58 2.2835 8.583 13.465 13.819 0.118 0.059
*Db is housing diameter for low shoulder. rb is housing fillet radius for low shoulder.

Application Data
Bearing Tolerances –– Table 10.12 thru Table 10.16 on page 314-17
Preload –– Table 10.46 on page 337
Shaft & Housing Fits –– Contact NSK engineering

194
Super [Link] 1/10/07 3:55 PM Page 15

Common Options
TR : Phenolic cage
TYN : Polyamide cage
DU : Duplex Universal
SU : Single Universal
L : Light Preload
M : Medium Preload
H : Heavy Preload
P4 : ISO 4 (ABEC 7) Precision
P5 : ISO 5 (ABEC 5) Precision

Bearing
Basic Load Ratings Limiting Speeds Weight
Bearing (lbs) (1000 RPM) (Approx.)
Number
Cr Cor Grease Oil lbs
7200 C 1210 590 57.5 87.5 0.07
7201 C 1770 870 52.3 79.6 0.08
7202 C 1950 1010 46 70 0.09
7203 C 2450 1310 40.4 61.5 0.14
7204 C 3260 1820 34.4 52.3 0.22
7205 C 3730 2290 29.9 45.5 0.28

7206 C 5180 3310 25 38.1 0.42

7207 C 6830 4480 21.5 32.8 0.60
7208 C 8160 5670 19.2 29.2 0.79
7209 C 9150 6480 17.7 27 0.87
7210 C 9590 7170 16.5 25 0.99

7211 C 11900 9040 14.9 22.6 1.29

7212 C 14400 11000 13.6 20.6 1.69
7213 C 16400 13200 12.5 19 2.19
7214 C 17900 14600 11.8 18 2.36
7215 C 18600 15700 11.3 17.1 2.58

7216 C 20800 17400 10.5 16 3.09

7217 C 24000 20400 9.8 14.9 3.90
7218 C 27600 23600 9.2 14 4.83
7219 C 29800 25100 8.7 13.3 5.73
7220 C 33500 28400 8.3 12.5 6.90

7221 C 36600 32200 7.8 11.9 8.22

7222 C 39500 35900 7.5 11.3 9.70
7224 C 44800 43200 6.9 10.5 11.84
7226 C 46500 47000 6.4 9.8 13.60
7228 C 53600 57100 5.9 9 17.29
7230 C 60800 68300 5.5 8.4 24.48

7232 C 64400 75000 5.2 7.8 30.65

7234 C 71700 87100 4.8 7.3 38.37
7236 C 75000 93700 4.6 7 39.25
7238 C 77200 101000 4.4 6.7 48.73
7240 C 82700 110000 4.2 6.3 57.77
Cr = Dynamic Radial Load Rating
Cor = Static Radial Load Rating

195
Super [Link] 1/10/07 3:55 PM Page 16

Super Precision
Angular Contact
7200A5 Series
25° Contact Angle

Basic Bearing Dimensions Preferred Shoulder Dimensions

Bearing
d D B da min Damax *Db max ra max *rb max
Number
mm inch mm inch mm inch inch inch inch inch inch
7200 A5 10 0.3937 30 1.1811 9 0.3543 0.591 0.984 1.083 0.024 0.012
7201 A5 12 0.4724 32 1.2598 10 0.3937 0.669 1.063 1.161 0.024 0.012
7202 A5 15 0.5906 35 1.3780 11 0.4331 0.787 1.181 1.280 0.024 0.012
7203 A5 17 0.6693 40 1.5748 12 0.4724 0.866 1.378 1.476 0.024 0.012
7204 A5 20 0.7874 47 1.8504 14 0.5512 1.024 1.614 1.654 0.039 0.020
7205 A5 25 0.9843 52 2.0472 15 0.5906 1.220 1.811 1.850 0.039 0.020

7206 A5 30 1.1811 62 2.4409 16 0.6299 1.417 2.205 2.244 0.039 0.020

7207 A5 35 1.3780 72 2.8346 17 0.6693 1.654 2.559 2.638 0.039 0.024
7208 A5 40 1.5748 80 3.1496 18 0.7087 1.850 2.874 2.953 0.039 0.024
7209 A5 45 1.7717 85 3.3465 19 0.7480 2.047 3.071 3.150 0.039 0.024
7210 A5 50 1.9685 90 3.5433 20 0.7874 2.244 3.268 3.346 0.039 0.024

7211 A5 55 2.1654 100 3.9370 21 0.8268 2.520 3.583 3.701 0.059 0.031
7212 A5 60 2.3622 110 4.3307 22 0.8661 2.717 3.976 4.094 0.059 0.031
7213 A5 65 2.5591 120 4.7244 23 0.9055 2.913 4.370 4.488 0.059 0.031
7214 A5 70 2.7559 125 4.9213 24 0.9449 3.110 4.567 4.685 0.059 0.031
7215 A5 75 2.9528 130 5.1181 25 0.9843 3.307 4.764 4.882 0.059 0.031

7216 A5 80 3.1496 140 5.5118 26 1.0236 3.543 5.118 5.276 0.079 0.039
7217 A5 85 3.3465 150 5.9055 28 1.1024 3.740 5.512 5.669 0.079 0.039
7218 A5 90 3.5433 160 6.2992 30 1.1811 3.937 5.906 6.063 0.079 0.039
7219 A5 95 3.7402 170 6.6929 32 1.2598 4.213 6.220 6.417 0.079 0.039
7220 A5 100 3.9370 180 7.0866 34 1.3386 4.409 6.614 6.811 0.079 0.039

7221 A5 105 4.1339 190 7.4803 36 1.4173 4.606 7.008 7.205 0.079 0.039
7222 A5 110 4.3307 200 7.8740 38 1.4961 4.803 7.402 7.598 0.079 0.039
7224 A5 120 4.7244 215 8.4646 40 1.5748 5.197 7.992 8.189 0.079 0.039
7226 A5 130 5.1181 230 9.0551 40 1.5748 5.669 8.504 8.780 0.098 0.039
7228 A5 140 5.5118 250 9.8425 42 1.6535 6.063 9.291 9.567 0.098 0.039
7230 A5 150 5.9055 270 10.6299 45 1.7717 6.457 10.079 10.354 0.098 0.039

7232 A5 160 6.2992 290 11.4173 48 1.8898 6.850 10.866 11.142 0.098 0.039
7234 A5 170 6.6929 310 12.2047 52 2.0472 7.402 11.496 11.850 0.118 0.059
7236 A5 180 7.0866 320 12.5984 52 2.0472 7.795 11.890 12.244 0.118 0.059
7238 A5 190 7.4803 340 13.3858 55 2.1654 8.189 12.677 13.031 0.118 0.059
7240 A5 200 7.8740 360 14.1732 58 2.2835 8.583 13.465 13.819 0.118 0.059
*Db is housing diameter for low shoulder. rb is housing fillet radius for low shoulder.

Application Data
Bearing Tolerances –– Table 10.12 thru Table 10.16 on page 314-17
Preload –– Table 10.46 on page 337
Shaft & Housing Fits –– Contact NSK engineering

196
Super [Link] 1/10/07 3:55 PM Page 17

Common Options
TR : Phenolic cage
TYN : Polyamide cage
DU : Duplex Universal
SU : Single Universal
L : Light Preload
M : Medium Preload
H : Heavy Preload
P4 : ISO 4 (ABEC 7) Precision
P5 : ISO 5 (ABEC 5) Precision

Bearing
Basic Load Ratings Limiting Speeds Weight
Bearing (lbs) (1000 RPM) (Approx.)
Number
Cr Cor Grease Oil lbs
7200 A5 1140 550 40.0 56.0 0.07
7201 A5 1720 840 36.0 50.0 0.08
7202 A5 1870 980 32.0 45.0 0.10
7203 A5 2360 1260 28.0 38.0 0.14
7204 A5 3150 1740 24.0 32.0 0.22
7205 A5 3570 2190 20.0 28.0 0.29

7206 A5 4960 3150 17.0 24.0 0.43

7207 A5 6550 4300 15.0 20.0 0.61
7208 A5 7830 5420 13.0 18.0 0.80
7209 A5 8820 6190 12.0 17.0 0.89
7210 A5 9150 6830 11.0 16.0 1.00

7211 A5 11400 8600 10.0 14.0 1.31

7212 A5 13800 10600 9.5 13.0 1.70
7213 A5 15700 12600 8.5 12.0 2.21
7214 A5 17100 13900 8.0 11.0 2.38
7215 A5 17700 15000 8.0 11.0 2.60

7216 A5 19800 16600 7.1 10.0 3.13

7217 A5 22900 19400 6.7 9.5 3.95
7218 A5 26200 22500 6.3 9.0 4.87
7219 A5 28400 24000 6.0 8.5 5.80
7220 A5 32000 27300 5.6 8.0 6.97

7221 A5 34800 30600 5.3 7.5 8.31

7222 A5 37700 34400 5.3 7.1 9.81
7224 A5 42500 41200 4.8 6.7 11.95
7226 A5 44100 44800 4.5 6.0 13.72
7228 A5 50900 54500 4.0 5.6 17.44
7230 A5 58000 65000 3.8 5.3 24.48

7232 A5 61300 71700 3.6 4.8 30.87

7234 A5 68300 83800 3.4 4.5 37.93
7236 A5 71700 89300 3.2 4.5 39.47
7238 A5 73900 95900 3.0 4.3 49.17
7240 A5 78300 105000 2.8 4.0 58.21
Cr = Dynamic Radial Load Rating
Cor = Static Radial Load Rating

197
Super [Link] 1/10/07 3:55 PM Page 18

Super Precision
Angular Contact
7900C Series
15° Contact Angle

Basic Bearing Dimensions Preferred Shoulder Dimensions

Bearing
d D B da min Damax *Db max ra max *rb max
Number
mm inch mm inch mm inch inch inch inch inch inch
7900 C 10 0.3937 22 0.8661 6 0.2362 0.492 0.768 0.819 0.012 0.006
7901 C 12 0.4724 24 0.9449 6 0.2362 0.571 0.846 0.898 0.012 0.006
7902 C 15 0.5906 28 1.1024 7 0.2756 0.689 1.004 1.055 0.012 0.006
7903 C 17 0.6693 30 1.1811 7 0.2756 0.768 1.083 1.134 0.012 0.006
7904 C 20 0.7874 37 1.4567 9 0.3543 0.886 1.358 1.409 0.012 0.006
7905 C 25 0.9843 42 1.6535 9 0.3543 1.083 1.555 1.606 0.012 0.006

7906 C 30 1.1811 47 1.8504 9 0.3543 1.280 1.752 1.803 0.012 0.006

7907 C 35 1.3780 55 2.1654 10 0.3937 1.575 1.969 2.067 0.024 0.012
7908 C 40 1.5748 62 2.4409 12 0.4724 1.772 2.244 2.343 0.024 0.012
7909 C 45 1.7717 68 2.6772 12 0.4724 1.969 2.480 2.579 0.024 0.012
7910 C 50 1.9685 72 2.8346 12 0.4724 2.165 2.638 2.736 0.024 0.012

7911 C 55 2.1654 80 3.1496 13 0.5118 2.402 2.913 2.953 0.039 0.020

7912 C 60 2.3622 85 3.3465 13 0.5118 2.598 3.110 3.150 0.039 0.020
7913 C 65 2.5591 90 3.5433 13 0.5118 2.795 3.307 3.346 0.039 0.020
7914 C 70 2.7559 100 3.9370 16 0.6299 2.992 3.701 3.740 0.039 0.020
7915 C 75 2.9528 105 4.1339 16 0.6299 3.189 3.898 3.937 0.039 0.020

7916 C 80 3.1496 110 4.3307 16 0.6299 3.386 4.094 4.134 0.039 0.020
7917 C 85 3.3465 120 4.7244 18 0.7087 3.622 4.449 4.528 0.039 0.024
7918 C 90 3.5433 125 4.9213 18 0.7087 3.819 4.646 4.724 0.039 0.024
7919 C 95 3.7402 130 5.1181 18 0.7087 4.016 4.843 4.921 0.039 0.024
7920 C 100 3.9370 140 5.5118 20 0.7874 4.213 5.236 5.315 0.039 0.024

7921 C 105 4.1339 145 5.7087 20 0.7874 4.409 5.433 5.512 0.039 0.024
7922 C 110 4.3307 150 5.9055 20 0.7874 4.606 5.630 5.709 0.039 0.024
7924 C 120 4.7244 165 6.4961 22 0.8661 5.000 6.220 6.299 0.039 0.024
7926 C 130 5.1181 180 7.0866 24 0.9449 5.472 6.732 6.850 0.059 0.031
7928 C 140 5.5118 190 7.4803 24 0.9449 5.866 7.126 7.244 0.059 0.031
7930 C 150 5.9055 210 8.2677 28 1.1024 6.299 7.874 8.031 0.079 0.039

7932 C 160 6.2992 220 8.6614 28 1.1024 6.693 8.268 8.425 0.079 0.039
7934 C 170 6.6929 230 9.0551 28 1.1024 7.087 8.661 8.819 0.079 0.039
7936 C 180 7.0866 250 9.8425 33 1.2992 7.480 9.449 9.606 0.079 0.039
7938 C 190 7.4803 260 10.2362 33 1.2992 7.874 9.843 10.000 0.079 0.039
7940 C 200 7.8740 280 11.0236 38 1.4961 8.346 10.551 10.748 0.079 0.039
*Db is housing diameter for low shoulder. rb is housing fillet radius for low shoulder.

Application Data
Bearing Tolerances –– Table 10.12 thru Table 10.16 on page 314-17
Preload –– Table 10.46 on page 337
Shaft & Housing Fits –– Contact NSK engineering

198
Super [Link] 1/10/07 3:55 PM Page 19

Common Options
TR : Phenolic cage
TYN : Polyamide cage
DU : Duplex Universal
SU : Single Universal
L : Light Preload
M : Medium Preload
H : Heavy Preload
P4 : ISO 4 (ABEC 7) Precision
P5 : ISO 5 (ABEC 5) Precision

Bearing Sealed
Basic Load Ratings Limiting Speeds Weight Design
Bearing (lbs) (1000 RPM) (Approx.)
Number
Cr Cor Grease Oil lbs
7900 C 670 340 71.9 109.4 0.02 –
7901 C 750 420 63.9 97.3 0.02 –
7902 C 1070 600 53.5 81.4 0.03 –
7903 C 1120 660 49 74.5 0.04 –
7904 C 1570 950 40.4 61.5 0.08 –
7905 C 1760 1220 34.4 52.3 0.09 –

7906 C 1860 1410 29.9 45.5 0.11 *

7907 C 2710 2050 25.6 38.9 0.16 *
7908 C 3400 2650 22.6 34.4 0.24 *
7909 C 3590 3000 20.4 31 0.28 *
7910 C 3790 3370 18.9 28.7 0.28 *

7911 C 4300 3990 17.1 26 0.39 *

7912 C 4370 4210 15.9 24.2 0.42 *
7913 C 4540 4610 14.9 22.6 0.45 *
7914 C 6330 6240 13.6 20.6 0.73 *
7915 C 6420 6570 12.8 19.5 0.78 *

7916 C 6530 6940 12.2 18.5 0.82 *

7917 C 8710 9150 11.3 17.1 1.15 *
7918 C 9370 10400 10.7 16.3 1.22 *
7919 C 9480 10800 10.3 15.6 1.28 *
7920 C 11200 12200 9.6 14.6 1.73 *

7921 C 11500 12800 9.2 14 1.79 –

7922 C 11700 13300 8.9 13.5 1.87 –
7924 C 16100 18300 8.1 12.3 2.51 –
7926 C 17600 20400 7.5 11.3 3.31 –
7928 C 17900 21400 7 10.7 3.55 –
7930 C 22900 27300 6.4 9.8 6.54 –

7932 C 23800 29800 6.1 9.3 6.81 –

7934 C 25400 33300 5.8 8.8 7.34 –
7936 C 32600 41400 5.4 8.2 10.80 –
7938 C 33100 43200 5.2 7.8 11.16 –
7940 C 42500 54900 4.8 7.3 15.10 –
Cr = Dynamic Radial Load Rating
Cor = Static Radial Load Rating

199
Super [Link] 1/10/07 3:55 PM Page 20

Super Precision
Angular Contact
7900A5 Series
25° Contact Angle

Basic Bearing Dimensions Preferred Shoulder Dimensions

Bearing
d D B da min Damax *Db max ra max *rb max
Number
mm inch mm inch mm inch inch inch inch inch inch
7900 A5 10 0.3937 22 0.8661 6 0.2362 0.492 0.768 0.819 0.012 0.006
7901 A5 12 0.4724 24 0.9449 6 0.2362 0.571 0.846 0.898 0.012 0.006
7902 A5 15 0.5906 28 1.1024 7 0.2756 0.689 1.004 1.055 0.012 0.006
7903 A5 17 0.6693 30 1.1811 7 0.2756 0.768 1.083 1.134 0.012 0.006
7904 A5 20 0.7874 37 1.4567 9 0.3543 0.886 1.358 1.409 0.012 0.006
7905 A5 25 0.9843 42 1.6535 9 0.3543 1.083 1.555 1.606 0.012 0.006

7906 A5 30 1.1811 47 1.8504 9 0.3543 1.280 1.752 1.803 0.012 0.006

7907 A5 35 1.3780 55 2.1654 10 0.3937 1.575 1.969 2.067 0.024 0.012
7908 A5 40 1.5748 62 2.4409 12 0.4724 1.772 2.244 2.343 0.024 0.012
7909 A5 45 1.7717 68 2.6772 12 0.4724 1.969 2.480 2.579 0.024 0.012
7910 A5 50 1.9685 72 2.8346 12 0.4724 2.165 2.638 2.736 0.024 0.012

7911 A5 55 2.1654 80 3.1496 13 0.5118 2.402 2.913 2.953 0.039 0.020

7912 A5 60 2.3622 85 3.3465 13 0.5118 2.598 3.110 3.150 0.039 0.020
7913 A5 65 2.5591 90 3.5433 13 0.5118 2.795 3.307 3.346 0.039 0.020
7914 A5 70 2.7559 100 3.9370 16 0.6299 2.992 3.701 3.740 0.039 0.020
7915 A5 75 2.9528 105 4.1339 16 0.6299 3.189 3.898 3.937 0.039 0.020

7916 A5 80 3.1496 110 4.3307 16 0.6299 3.386 4.094 4.134 0.039 0.020
7917 A5 85 3.3465 120 4.7244 18 0.7087 3.622 4.449 4.528 0.039 0.024
7918 A5 90 3.5433 125 4.9213 18 0.7087 3.819 4.646 4.724 0.039 0.024
7919 A5 95 3.7402 130 5.1181 18 0.7087 4.016 4.843 4.921 0.039 0.024
7920 A5 100 3.9370 140 5.5118 20 0.7874 4.213 5.236 5.315 0.039 0.024

7921 A5 105 4.1339 145 5.7087 20 0.7874 4.409 5.433 5.512 0.039 0.024
7922 A5 110 4.3307 150 5.9055 20 0.7874 4.606 5.630 5.709 0.039 0.024
7924 A5 120 4.7244 165 6.4961 22 0.8661 5.000 6.220 6.299 0.039 0.024
7926 A5 130 5.1181 180 7.0866 24 0.9449 5.472 6.732 6.850 0.059 0.031
7928 A5 140 5.5118 190 7.4803 24 0.9449 5.866 7.126 7.244 0.059 0.031
7930 A5 150 5.9055 210 8.2677 28 1.1024 6.299 7.874 8.031 0.079 0.039

7932 A5 160 6.2992 220 8.6614 28 1.1024 6.693 8.268 8.425 0.079 0.039
7934 A5 170 6.6929 230 9.0551 28 1.1024 7.087 8.661 8.819 0.079 0.039
7936 A5 180 7.0866 250 9.8425 33 1.2992 7.480 9.449 9.606 0.079 0.039
7938 A5 190 7.4803 260 10.2362 33 1.2992 7.874 9.843 10.000 0.079 0.039
7940 A5 200 7.8740 280 11.0236 38 1.4961 8.346 10.551 10.748 0.079 0.039
*Db is housing diameter for low shoulder. rb is housing fillet radius for low shoulder.

Application Data
Bearing Tolerances –– Table 10.12 thru Table 10.16 on page 314-17
Preload –– Table 10.46 on page 337
Shaft & Housing Fits –– Contact NSK engineering

200
Super [Link] 1/10/07 3:55 PM Page 21

Common Options
TR : Phenolic cage
TYN : Polyamide cage
DU : Duplex Universal
SU : Single Universal
L : Light Preload
M : Medium Preload
H : Heavy Preload
P4 : ISO 4 (ABEC 7) Precision
P5 : ISO 5 (ABEC 5) Precision

Bearing Sealed
Basic Load Ratings Limiting Speeds Weight
Bearing (lbs) Design
(1000 RPM) (Approx.)
Number
Cr Cor Grease Oil lbs
7900 A5 650 330 62.5 93.8 0.02 –
7901 A5 720 400 55.6 83.4 0.02 –
7902 A5 1030 570 46.6 69.8 0.03 –
7903 A5 1070 630 42.6 63.9 0.04 –
7904 A5 1490 900 35.1 52.7 0.08 –
7905 A5 1680 1160 29.9 44.8 0.09 –

7906 A5 1760 1330 26 39 0.11 *

7907 A5 2580 1950 22.3 33.4 0.16 *
7908 A5 3220 2510 19.7 29.5 0.24 *
7909 A5 3400 2840 17.7 26.6 0.28 *
7910 A5 3590 3200 16.4 24.6 0.29 *

7911 A5 4060 3770 14.9 22.3 0.40 *

7912 A5 4120 3990 13.8 20.7 0.38 *
7913 A5 4280 4370 13 19.4 0.45 *
7914 A5 5970 5910 11.8 17.7 0.74 *
7915 A5 6060 6220 11.2 16.7 0.78 *

7916 A5 6150 6530 10.6 15.8 0.83 *

7917 A5 8270 8600 9.8 14.7 1.16 *
7918 A5 8820 9810 9.4 14 1.23 *
7919 A5 8930 10300 8.9 13.4 1.30 *
7920 A5 10700 11600 8.4 12.5 1.75 *

7921 A5 10800 12100 8 12 1.81 –

7922 A5 11000 12700 7.7 11.6 1.89 –
7924 A5 15200 17300 7.1 10.6 2.54 –
7926 A5 16600 19300 6.5 9.7 3.35 –
7928 A5 16900 20300 6.1 9.1 3.59 –
7930 A5 21700 26000 5.6 8.4 6.55 –

7932 A5 22500 28200 5.3 7.9 6.88 –

7934 A5 23800 31500 5 7.5 7.41 –
7936 A5 30600 39200 4.7 7 10.89 –
7938 A5 31100 40800 4.5 6.7 11.29 –
7940 A5 40100 52000 4.2 6.3 15.26 –
Cr = Dynamic Radial Load Rating
Cor = Static Radial Load Rating

201
Super [Link] 1/10/07 3:55 PM Page 22

High Speed
Super Precision
Angular Contact
BNC Series (Steel ball)
15° Contact Angle

Basic Bearing Dimensions Preferred Shoulder Dimensions

Part
d D B da min Damax *Db max ra max *rb max
Number
mm inch mm inch mm inch inch inch inch inch inch
30BNC10 30 1.1811 55 2.1654 13 0.5118 1.417 1.929 1.969 0.039 0.020
35BNC10 35 1.3780 62 2.4409 14 0.5512 1.614 2.205 2.244 0.039 0.020
40BNC10 40 1.5748 68 2.6772 15 0.5906 1.811 2.441 2.480 0.039 0.020
45BNC10 45 1.7717 75 2.9528 16 0.6299 2.008 2.717 2.756 0.039 0.020
50BNC10 50 1.9685 80 3.1496 16 0.6299 2.205 2.913 2.953 0.039 0.020

55BNC10 55 2.1654 90 3.5433 18 0.7087 2.441 3.268 3.346 0.039 0.024

60BNC10 60 2.3622 95 3.7402 18 0.7087 2.638 3.465 3.543 0.039 0.024
65BNC10 65 2.5591 100 3.9370 18 0.7087 2.835 3.661 3.740 0.039 0.024
70BNC10 70 2.7559 110 4.3307 20 0.7874 0.433 4.055 4.134 0.039 0.024
75BNC10 75 2.9528 115 4.5276 20 0.7874 3.228 4.252 4.331 0.039 0.024

80BNC10 80 3.1496 125 4.9213 22 0.8661 3.425 4.646 4.724 0.039 0.024
85BNC10 85 3.3465 130 5.1181 22 0.8661 3.622 4.843 4.921 0.039 0.024
90BNC10 90 3.5433 140 5.5118 24 0.9449 3.898 5.157 5.276 0.059 0.031
95BNC10 95 3.7402 145 5.7087 24 0.9449 4.094 5.354 5.472 0.059 0.031
100BNC10 100 3.9370 150 5.9055 24 0.9449 4.173 5.551 5.669 0.059 0.031

105BNC10 105 4.1339 160 6.2992 26 1.0236 4.528 5.906 6.063 0.079 0.039
110BNC10 110 4.3307 170 6.6929 28 1.1024 4.724 6.299 6.457 0.079 0.039

Limiting Speeds
The limiting speeds listed in the Bearing Dimensional Tables are guideline values. They are based on a single bearing that is lightly preloaded by means of a spring and subjected to a relatively
light load with good heat dissipation.
The limiting speeds with grease lubrication are determined using high quality grease in appropriate amounts. Those listed for oil lubrication are based on the use of oil-air (or oil mist)
lubrication. In situations where the lubricating oil is used as a means to remove heat, higher speed can be achieved, however a large amount of oil must be pressure fed through the bearing, so
there is a significant loss of spindle power.
When single bearings are used in two, three or four row combinations, or the preload is increased to improve spindle rigidity, limiting speeds will be lower than those listed by the factors in the
table below.

Speed Factor
Arrangement EL L M H
DB 0.85 0.80 0.65 0.55
DBB 0.80 0.75 0.60 0.45
DBD 0.75 0.70 0.55 0.40

*Db is housing diameter for low shoulder. rb is housing fillet radius for low shoulder.

202
Super [Link] 1/10/07 3:55 PM Page 23

Common Options
TR : Phenolic cage
TYN : Polyamide cage
DU : Duplex Universal
SU : Single Universal
L : Light Preload
M : Medium Preload
H : Heavy Preload
P4 : ISO 4 (ABEC 7) Precision
P5 : ISO 5 (ABEC 5) Precision

Limiting Speed Bearing Preload

Basic Load Ratings Weight Value
Part Single or Tandem Duplex
(lbs) (RPM) (Approx.)
Number (EL)
Cr Cor Grease Oil lbs lbs
30BNC10 2590 2000 28000 40000 0.27 11.24
35BNC10 2990 2450 26000 36000 0.36 11.24
40BNC10 3120 2740 22000 32000 0.44 11.24
45BNC10 3480 3150 20000 28000 0.56 11.24
50BNC10 3640 3460 19000 26000 0.61 11.24

55BNC10 4500 4380 17000 24000 0.90 11.24

60BNC10 4680 4790 15000 22000 0.97 11.24
65BNC10 4860 5220 15000 20000 1.05 11.24
70BNC10 6610 6860 13000 19000 1.40 11.24
75BNC10 6720 7190 13000 18000 1.48 11.24

80BNC10 7870 8540 12000 17000 2.02 22.48

85BNC10 7980 8880 11000 16000 2.11 22.48
90BNC10 10450 11580 11000 15000 2.71 22.48
95BNC10 10680 12030 10000 14000 2.82 22.48
100BNC10 10790 12590 9500 14000 2.93 22.48

105BNC10 12590 14950 9000 13000 3.81 22.48

110BNC10 13830 16410 8500 12000 4.65 22.48
Cr = Dynamic Radial Load Rating
Cor = Static Radial Load Rating

203
Super [Link] 1/10/07 3:55 PM Page 24

High Speed
Super Precision
Angular Contact
BNC Series (Ceramic ball) (Continued)
15° Contact Angle

Basic Bearing Dimensions Preferred Shoulder Dimensions

Part
d D B da min Damax *Db max ra max *rb max
Number
mm inch mm inch mm inch inch inch inch inch inch
30BNC10SN24 30 1.1811 55 2.1654 13 0.5118 1.417 1.929 1.969 0.039 0.020
35BNC10SN24 35 1.3780 62 2.4409 14 0.5512 1.614 2.205 2.244 0.039 0.020
40BNC10SN24 40 1.5748 68 2.6772 15 0.5906 1.811 2.441 2.480 0.039 0.020
45BNC10SN24 45 1.7717 75 2.9528 16 0.6299 2.008 2.717 2.756 0.039 0.020
50BNC10SN24 50 1.9685 80 3.1496 16 0.6299 2.205 2.913 2.953 0.039 0.020

55BNC10SN24 55 2.1654 90 3.5433 18 0.7087 2.441 3.268 3.346 0.039 0.024

60BNC10SN24 60 2.3622 95 3.7402 18 0.7087 2.638 3.465 3.543 0.039 0.024
65BNC10SN24 65 2.5591 100 3.9370 18 0.7087 2.835 3.661 3.740 0.039 0.024
70BNC10SN24 70 2.7559 110 4.3307 20 0.7874 0.433 4.055 4.134 0.039 0.024
75BNC10SN24 75 2.9528 115 4.5276 20 0.7874 3.228 4.252 4.331 0.039 0.024

80BNC10SN24 80 3.1496 125 4.9213 22 0.8661 3.425 4.646 4.724 0.039 0.024
85BNC10SN24 85 3.3465 130 5.1181 22 0.8661 3.622 4.843 4.921 0.039 0.024
90BNC10SN24 90 3.5433 140 5.5118 24 0.9449 3.898 5.157 5.276 0.059 0.031
95BNC10SN24 95 3.7402 145 5.7087 24 0.9449 4.094 5.354 5.472 0.059 0.031
100BNC10SN24 100 3.9370 150 5.9055 24 0.9449 4.173 5.551 5.669 0.059 0.031

105BNC10SN24 105 4.1339 160 6.2992 26 1.0236 4.528 5.906 6.063 0.079 0.039
110BNC10SN24 110 4.3307 170 6.6929 28 1.1024 4.724 6.299 6.457 0.079 0.039

Limiting Speeds
The limiting speeds listed in the Bearing Dimensional Tables are guideline values. They are based on a single bearing that is lightly preloaded by means of a spring and subjected to a relatively
light load with good heat dissipation.
The limiting speeds with grease lubrication are determined using high quality grease in appropriate amounts. Those listed for oil lubrication are based on the use of oil-air (or oil mist)
lubrication. In situations where the lubricating oil is used as a means to remove heat, higher speed can be achieved, however a large amount of oil must be pressure fed through the bearing, so
there is a significant loss of spindle power.
When single bearings are used in two, three or four row combinations, or the preload is increased to improve spindle rigidity, limiting speeds will be lower than those listed by the factors in the
table below.

Speed Factor
Arrangement EL L M H
DB 0.85 0.80 0.65 0.55
DBB 0.80 0.75 0.60 0.45
DBD 0.75 0.70 0.55 0.40

*Db is housing diameter for low shoulder. rb is housing fillet radius for low shoulder.

204
Super [Link] 1/10/07 3:55 PM Page 25

Common Options
TR : Phenolic cage
TYN : Polyamide cage
DU : Duplex Universal
SU : Single Universal
L : Light Preload
M : Medium Preload
H : Heavy Preload
P4 : ISO 4 (ABEC 7) Precision
P5 : ISO 5 (ABEC 5) Precision

Limiting Speed Bearing Preload

Basic Load Ratings Weight Value
Part Single or Tandem Duplex
(lbs) (RPM) (Approx.)
Number (EL)
Cr Cor Grease Oil lbs lbs
30BNC10SN24 2590 2000 34000 57000 0.27 11.24
35BNC10SN24 2990 2450 30000 50000 0.36 11.24
40BNC10SN24 3120 2740 27000 45000 0.44 11.24
45BNC10SN24 3480 3150 24000 41000 0.56 11.24
50BNC10SN24 3640 3460 22000 38000 0.61 11.24

55BNC10SN24 4500 4380 20000 34000 0.90 11.24

60BNC10SN24 4680 4790 19000 31000 0.97 11.24
65BNC10SN24 4860 5220 17000 30000 1.05 11.24
70BNC10SN24 6610 6860 16000 27000 1.40 11.24
75BNC10SN24 6720 7190 15000 26000 1.48 11.24

80BNC10SN24 7870 8540 14000 24000 2.02 22.48

85BNC10SN24 7980 8880 13000 23000 2.11 22.48
90BNC10SN24 10450 11580 13000 21000 2.71 22.48
95BNC10SN24 10680 12030 12000 20000 2.82 22.48
100BNC10SN24 10790 12590 12000 20000 2.93 22.48

105BNC10SN24 12590 14950 11000 18000 3.81 22.48

110BNC10SN24 13830 16410 10000 17000 4.65 22.48
Cr = Dynamic Radial Load Rating
Cor = Static Radial Load Rating

205
Super [Link] 1/10/07 3:55 PM Page 26

High Speed
Super Precision
Angular Contact
BNR Series - ROBUST (Steel ball)
18° Contact Angle

Basic Bearing Dimensions Preferred Shoulder Dimensions

Part
d D B da min Damax *Db max ra max *rb max
Number
mm inch mm inch mm inch inch inch inch inch inch
30BNR10S 30 1.1811 55 2.1654 13 0.5118 1.417 1.929 1.969 0.039 0.020
35BNR10S 35 1.3780 62 2.4409 14 0.5512 1.614 2.205 2.244 0.039 0.020
40BNR10S 40 1.5748 68 2.6772 15 0.5906 1.811 2.441 2.480 0.039 0.020
45BNR10S 45 1.7717 75 2.9528 16 0.6299 2.008 2.717 2.756 0.039 0.020
50BNR10S 50 1.9685 80 3.1496 16 0.6299 2.205 2.913 2.953 0.039 0.020

55BNR10S 55 2.1654 90 3.5433 18 0.7087 2.441 3.268 3.346 0.039 0.024

60BNR10S 60 2.3622 95 3.7402 18 0.7087 2.638 3.465 3.543 0.039 0.024
65BNR10S 65 2.5591 100 3.9370 18 0.7087 2.835 3.661 3.740 0.039 0.024
70BNR10S 70 2.7559 110 4.3307 20 0.7874 0.433 4.055 4.134 0.039 0.024
75BNR10S 75 2.9528 115 4.5276 20 0.7874 3.228 4.252 4.331 0.039 0.024

80BNR10S 80 3.1496 125 4.9213 22 0.8661 3.425 4.646 4.724 0.039 0.024
85BNR10S 85 3.3465 130 5.1181 22 0.8661 3.622 4.843 4.921 0.039 0.024
90BNR10S 90 3.5433 140 5.5118 24 0.9449 3.898 5.157 5.276 0.059 0.031
95BNR10S 95 3.7402 145 5.7087 24 0.9449 4.094 5.354 5.472 0.059 0.031
100BNR10S 100 3.9370 150 5.9055 24 0.9449 4.291 5.551 5.669 0.059 0.031

Limiting Speeds
The limiting speeds listed in the Bearing Dimensional Tables are guideline values. They are based on a single bearing that is lightly preloaded by means of a spring and subjected to a relatively
light load with good heat dissipation.
The limiting speeds with grease lubrication are determined using high quality grease in appropriate amounts. Those listed for oil lubrication are based on the use of oil-air (or oil mist)
lubrication. In situations where the lubricating oil is used as a means to remove heat, higher speed can be achieved, however a large amount of oil must be pressure fed through the bearing, so
there is a significant loss of spindle power.
When single bearings are used in two, three or four row combinations, or the preload is increased to improve spindle rigidity, limiting speeds will be lower than those listed by the factors in the
table below.

Speed Factor
Arrangement EL L M H
DB 0.85 0.80 0.65 0.55
DBB 0.80 0.75 0.60 0.45
DBD 0.75 0.70 0.55 0.40

*Db is housing diameter for low shoulder. rb is housing fillet radius for low shoulder.

206
Super [Link] 1/10/07 3:55 PM Page 27

Common Options
TR : Phenolic cage
TYN : Polyamide cage
DU : Duplex Universal
SU : Single Universal
L : Light Preload
M : Medium Preload
H : Heavy Preload
P4 : ISO 4 (ABEC 7) Precision
P5 : ISO 5 (ABEC 5) Precision

Limiting Speed Bearing Preload

Basic Load Ratings Weight Value
Part Single or Tandem Duplex
(lbs) (RPM) (Approx.)
Number (EL)
Cr Cor Grease Oil lbs lbs
30BNR10S 1940 1290 33000 47100 0.273 11.24
35BNR10S 2270 1600 28900 41300 0.362 11.24
40BNR10S 2380 1790 26000 37100 0.450 11.24
45BNR10S 2630 2020 23400 33400 0.571 11.24
50BNR10S 2740 2230 21600 30800 0.620 11.24

55BNR10S 3390 2810 19400 27600 0.913 11.24

60BNR10S 3510 3080 18100 25900 0.977 11.24
65BNR10S 3640 3330 17000 24300 1.041 11.24
70BNR10S 5010 4450 15600 22300 1.422 11.24
75BNR10S 5080 4650 14800 21100 1.497 11.24

80BNR10S 5960 5510 13700 19600 2.031 22.48

85BNR10S 6020 5780 13100 18700 2.121 22.48
90BNR10S 7870 7420 12200 17400 2.736 22.48
95BNR10S 7980 7760 11700 16700 2.862 22.48
100BNR10S 8090 8090 11200 16000 2.745 22.48
Cr = Dynamic Radial Load Rating
Cor = Static Radial Load Rating

207
Super [Link] 1/10/07 3:55 PM Page 28

Super Precision
Angular Contact
BNR Series - ROBUST (Ceramic ball) (Continued)
18° Contact Angle

Basic Bearing Dimensions Preferred Shoulder Dimensions

Part
d D B da min Damax *Db max ra max *rb max
Number
mm inch mm inch mm inch inch inch inch inch inch
30BNR10H 30 1.1811 55 2.1654 13 0.5118 1.417 1.929 1.969 0.039 0.020
35BNR10H 35 1.3780 62 2.4409 14 0.5512 1.614 2.205 2.244 0.039 0.020
40BNR10H 40 1.5748 68 2.6772 15 0.5906 1.811 2.441 2.480 0.039 0.020
45BNR10H 45 1.7717 75 2.9528 16 0.6299 2.008 2.717 2.756 0.039 0.020
50BNR10H 50 1.9685 80 3.1496 16 0.6299 2.205 2.913 2.953 0.039 0.020

55BNR10H 55 2.1654 90 3.5433 18 0.7087 2.441 3.268 3.346 0.039 0.024

60BNR10H 60 2.3622 95 3.7402 18 0.7087 2.638 3.465 3.543 0.039 0.024
65BNR10H 65 2.5591 100 3.9370 18 0.7087 2.835 3.661 3.740 0.039 0.024
70BNR10H 70 2.7559 110 4.3307 20 0.7874 0.433 4.055 4.134 0.039 0.024
75BNR10H 75 2.9528 115 4.5276 20 0.7874 3.228 4.252 4.331 0.039 0.024

80BNR10H 80 3.1496 125 4.9213 22 0.8661 3.425 4.646 4.724 0.039 0.024
85BNR10H 85 3.3465 130 5.1181 22 0.8661 3.622 4.843 4.921 0.039 0.024
90BNR10H 90 3.5433 140 5.5118 24 0.9449 3.898 5.157 5.276 0.059 0.031
95BNR10H 95 3.7402 145 5.7087 24 0.9449 4.094 5.354 5.472 0.059 0.031
100BNR10H 100 3.9370 150 5.9055 24 0.9449 4.291 5.551 5.669 0.059 0.031
Limiting Speeds
The limiting speeds listed in the Bearing Dimensional Tables are guideline values. They are based on a single bearing that is lightly preloaded by means of a spring and subjected to a relatively
light load with good heat dissipation.
The limiting speeds with grease lubrication are determined using high quality grease in appropriate amounts. Those listed for oil lubrication are based on the use of oil-air (or oil mist)
lubrication. In situations where the lubricating oil is used as a means to remove heat, higher speed can be achieved, however a large amount of oil must be pressure fed through the bearing, so
there is a significant loss of spindle power.
When single bearings are used in two, three or four row combinations, or the preload is increased to improve spindle rigidity, limiting speeds will be lower than those listed by the factors in the
table below.

Speed Factor
Arrangement EL L M H
DB 0.85 0.80 0.65 0.55
DBB 0.80 0.75 0.60 0.45
DBD 0.75 0.70 0.55 0.40

*Db is housing diameter for low shoulder. rb is housing fillet radius for low shoulder.

208
Super [Link] 1/10/07 3:55 PM Page 29

Common Options
TR : Phenolic cage
TYN : Polyamide cage
DU : Duplex Universal
SU : Single Universal
L : Light Preload
M : Medium Preload
H : Heavy Preload
P4 : ISO 4 (ABEC 7) Precision
P5 : ISO 5 (ABEC 5) Precision

Limiting Speed Bearing Preload

Basic Load Ratings Weight Value
Part Single or Tandem Duplex
(lbs) (RPM) (Approx.)
Number (EL)
Cr Cor Grease Oil lbs lbs
30BNR10H 1940 1290 42400 65900 0.273 11.24
35BNR10H 2270 1600 37200 57800 0.362 11.24
40BNR10H 2380 1790 33400 51900 0.450 11.24
45BNR10H 2630 2020 30000 46700 0.571 11.24
50BNR10H 2740 2230 27700 43100 0.620 11.24

55BNR10H 3390 2810 24900 38700 0.913 11.24

60BNR10H 3510 3080 23300 36200 0.977 11.24
65BNR10H 3640 3330 21900 34000 1.041 11.24
70BNR10H 5010 4450 20000 31200 1.422 11.24
75BNR10H 5080 4650 19000 29500 1.497 11.24

80BNR10H 5960 5510 17600 27400 2.031 22.48

85BNR10H 6020 5780 16800 26100 2.121 22.48
90BNR10H 7870 7420 15700 24400 2.736 22.48
95BNR10H 7980 7760 15000 23400 2.862 22.48
100BNR10H 8090 8090 14400 22400 2.745 22.48
Cr = Dynamic Radial Load Rating
Cor = Static Radial Load Rating

209
Super [Link] 1/10/07 3:55 PM Page 30

High Speed
Super Precision
Angular Contact
BGR Series (Steel ball)
15° Contact Angle

Basic Bearing Dimensions Preferred Shoulder Dimensions

Part
d D B da min Damax ra max *rb max
Number
mm inch mm inch mm inch inch inch inch inch
6BGR10S 6 0.2362 17 0.6693 6 0.2362 0.335 0.571 0.012 -
7BGR10S 7 0.2756 19 0.7480 6 0.2362 0.374 0.650 0.012 -
8BGR10S 8 0.3150 22 0.8661 7 0.2756 0.413 0.768 0.012 -
10BGR10S 10 0.3937 26 1.0236 8 0.3150 0.492 0.925 0.012 0.0059

12BGR10S 12 0.4724 28 1.1024 8 0.3150 0.571 1.004 0.012 0.0059

15BGR10S 15 0.5906 32 1.2598 9 0.3543 0.689 1.161 0.012 0.0059
17BGR10S 17 0.6693 35 1.3780 10 0.3937 0.768 1.280 0.012 0.0059
20BGR10S 20 0.7874 42 1.6535 12 0.4724 0.984 1.457 0.024 0.0118
25BGR10S 25 0.9843 47 1.8504 12 0.4724 1.181 1.654 0.024 0.0118
rb is housing fillet radius for low shoulder.

Limiting Speeds
The limiting speeds listed in the Bearing Dimensional Tables are guideline values. They are based on a single bearing that is lightly preloaded by means of a spring and subjected to a relatively
light load with good heat dissipation.
The limiting speeds with grease lubrication are determined using high quality grease in appropriate amounts. Those listed for oil lubrication are based on the use of oil-air (or oil mist)
lubrication. In situations where the lubricating oil is used as a means to remove heat, higher speed can be achieved, however a large amount of oil must be pressure fed through the bearing, so
there is a significant loss of spindle power.
When single bearings are used in two, three or four row combinations, or the preload is increased to improve spindle rigidity, limiting speeds will be lower than those listed by the factors in the
table below.

Speed Factor
Arrangement EL L M H
DB 0.85 0.80 0.65 0.55
DBB 0.80 0.75 0.60 0.45
DBD 0.75 0.70 0.55 0.40

210
Super [Link] 1/10/07 3:55 PM Page 31

Common Options
TR : Phenolic cage
TYN : Polyamide cage
DU : Duplex Universal
SU : Single Universal
L : Light Preload
M : Medium Preload
H : Heavy Preload
P4 : ISO 4 (ABEC 7) Precision
P5 : ISO 5 (ABEC 5) Precision

Limiting Speed Bearing

Basic Load Ratings Single or Tandem Weight
Part (lbs)
Number 1000 (RPM) (Approx.)

Cr Cor Grease Oil lbs

6BGR10S 320 100 140 192 0.01
7BGR10S 370 120 124 170 0.02
8BGR10S 530 180 107 147 0.03
10BGR10S 800 290 88.9 123 0.04

12BGR10S 880 330 80 110 0.05

15BGR10S 940 390 68.1 93.7 0.06
17BGR10S 1010 440 61.6 84.7 0.08
20BGR10S 1690 750 51.7 71 0.15
25BGR10S 1790 850 44.5 61.2 0.17
Cr = Dynamic Radial Load Rating
Cor = Static Radial Load Rating

211
Super [Link] 1/10/07 3:55 PM Page 32

Super Precision
Angular Contact
BGR Series (Ceramic ball) (Continued)
15° Contact Angle

Basic Bearing Dimensions Preferred Shoulder Dimensions

Part
d D B da min Damax ra max *rb max
Number
mm inch mm inch mm inch inch inch inch inch
6BGR10H 6 0.2362 17 0.6693 6 0.2362 0.335 0.571 0.012 -
7BGR10H 7 0.2756 19 0.7480 6 0.2362 0.374 0.650 0.012 -
8BGR10H 8 0.3150 22 0.8661 7 0.2756 0.413 0.768 0.012 -
10BGR10H 10 0.3937 26 1.0236 8 0.3150 0.492 0.925 0.012 0.0059

12BGR10H 12 0.4724 28 1.1024 8 0.3150 0.571 1.004 0.012 0.0059

15BGR10H 15 0.5906 32 1.2598 9 0.3543 0.689 1.161 0.012 0.0059
17BGR10H 17 0.6693 35 1.3780 10 0.3937 0.768 1.280 0.012 0.0059
20BGR10H 20 0.7874 42 1.6535 12 0.4724 0.984 1.457 0.024 0.0118
25BGR10H 25 0.9843 47 1.8504 12 0.4724 1.181 1.654 0.024 0.0118
rb is housing fillet radius for low shoulder.

Limiting Speeds
The limiting speeds listed in the Bearing Dimensional Tables are guideline values. They are based on a single bearing that is lightly preloaded by means of a spring and subjected to a relatively
light load with good heat dissipation.
The limiting speeds with grease lubrication are determined using high quality grease in appropriate amounts. Those listed for oil lubrication are based on the use of oil-air (or oil mist)
lubrication. In situations where the lubricating oil is used as a means to remove heat, higher speed can be achieved, however a large amount of oil must be pressure fed through the bearing, so
there is a significant loss of spindle power.
When single bearings are used in two, three or four row combinations, or the preload is increased to improve spindle rigidity, limiting speeds will be lower than those listed by the factors in the
table below.

Speed Factor
Arrangement EL L M H
DB 0.85 0.80 0.65 0.55
DBB 0.80 0.75 0.60 0.45
DBD 0.75 0.70 0.55 0.40

212
Super [Link] 1/10/07 3:55 PM Page 33

Limiting Speed Bearing

Basic Load Ratings Single or Tandem Weight
Part (lbs)
Number 1000 (RPM) (Approx.)

Cr Cor Grease Oil lbs

6BGR10H 320 100 166 244 0.01
7BGR10H 370 120 147 216 0.02
8BGR10H 530 180 127 187 0.03
10BGR10H 800 290 106 156 0.04

12BGR10H 880 330 95 140 0.05

15BGR10H 940 390 80.9 120 0.06
17BGR10H 1010 440 73.1 108 0.08
20BGR10H 1690 750 61.3 90.4 0.15
25BGR10H 1790 850 52.8 77.8 0.17
Cr = Dynamic Radial Load Rating
Cor = Static Radial Load Rating

213
Super [Link] 1/10/07 3:55 PM Page 34

Super Precision
Thrust Angular Contact
BAR Series
30° Contact Angle

Preferred Shoulder
Basic Bearing Dimensions Dimensions
Part
Number d D B da min Dbmax *rb max
mm inch mm inch mm inch inch inch inch
60BAR10S 60 2.3622 95 3.7402 16.5 0.6496 2.6378 3.54331 0.02362
65BAR10S 65 2.5591 100 3.9370 16.5 0.6496 2.8346 3.74015 0.02362
70BAR10S 70 2.7559 110 4.3307 18 0.7087 3.0315 4.13385 0.02362
75BAR10S 75 2.9528 115 4.5276 18 0.7087 3.2283 4.33070 0.02362

80BAR10S 80 3.1496 125 4.9213 20.25 0.7972 3.4252 4.72440 0.02362

85BAR10S 85 3.3465 130 5.1181 20.25 0.7972 3.6220 4.92125 0.02362
90BAR10S 90 3.5433 140 5.5118 22.5 0.8858 3.8976 5.27559 0.03937
95BAR10S 95 3.7402 145 5.7087 22.5 0.8858 4.0945 5.47244 0.03937

100BAR10S 100 3.9370 150 5.9055 22.5 0.8858 4.2913 5.66929 0.03937
105BAR10S 105 4.1339 160 6.2992 24.75 0.9744 4.5276 6.06299 0.03937
110BAR10S 110 4.3307 170 6.6929 27 1.0630 4.7244 6.45669 0.03937
120BAR10S 120 4.7244 180 7.0866 27 1.0630 5.1181 6.85039 0.03937
130BAR10S 130 5.1181 200 7.8740 31.5 1.2402 5.5118 7.63779 0.03937
rb is housing fillet radius for low shoulder.

214
Super [Link] 1/10/07 3:55 PM Page 35

Common Options
TR : Phenolic cage
TYN : Polyamide cage
DU : Duplex Universal
SU : Single Universal
L : Light Preload
M : Medium Preload
H : Heavy Preload
P4 : ISO 4 (ABEC 7) Precision
P5 : ISO 5 (ABEC 5) Precision

Preload Axial
Limiting Speed Bearing Rigidity
Basic Load Ratings Weight Value
Part Duplex Duplex Duplex
(lbs) (RPM) (Approx.)
Number (EL) (EL)
Cr Cor Grease Oil lbs lbs lbs/.001 inch
60BAR10S 4249 8543 9 700 12 300 0.93 53.95 1084.9
65BAR10S 4384 9330 9 100 11 600 0.99 56.20 1142
70BAR10S 6047 12364 8 400 10 600 1.32 56.20 1142
75BAR10S 6137 13039 7 900 10 000 1.40 58.45 1199.1

80BAR10S 7194 15399 7 400 9 300 1.93 76.44 1370.4

85BAR10S 73064 16074 7 000 8 900 2.14 78.68 1370.4
90BAR10S 95544 20795 6 600 8 300 2.64 80.93 1427.5
95BAR10S 9667 21694 6 300 8 000 2.91 80.93 1484.6

100BAR10S 9779 22481 6 000 7 600 3.08 83.18 1541.7

105BAR10S 11128 25853 5 700 7 200 3.83 85.43 1598.8
110BAR10S 12477 29450 5 400 6 800 4.65 87.68 1598.8
120BAR10S 12814 31698 5 000 6 400 4.99 87.68 1713
130BAR10S 16299 38667 4 600 5 800 7.41 87.68 1713
Cr = Dynamic Radial Load Rating
Cor = Static Radial Load Rating

215
Super [Link] 1/10/07 3:55 PM Page 36

Super Precision
Thrust Angular Contact
BTR Series (Continued)
40° Contact Angle

Preferred Shoulder
Basic Bearing Dimensions Dimensions
Part
Number d D B da min Dbmax *rb max
mm inch mm inch mm inch inch inch inch
60BTR10S 60 2.3622 95 3.7402 16.5 0.6496 2.6378 3.5433 0.02362
65BTR10S 65 2.5591 100 3.9370 16.5 0.6496 2.8346 3.7402 0.02362
70BTR10S 70 2.7559 110 4.3307 18 0.7087 3.0315 4.1339 0.02362
75BTR10S 75 2.9528 115 4.5276 18 0.7087 3.2283 4.3307 0.02362
80BTR10S 80 3.1496 125 4.9213 20.25 0.7972 3.4252 4.7244 0.02362

85BTR10S 85 3.3465 130 5.1181 20.25 0.7972 3.6220 4.9213 0.02362

90BTR10S 90 3.5433 140 5.5118 22.5 0.8858 3.8976 5.2756 0.03937
95BTR10S 95 3.7402 145 5.7087 22.5 0.8858 4.0945 5.4724 0.03937
100BTR10S 100 3.9370 150 5.9055 22.5 0.8858 4.2913 5.6693 0.03937

105BTR10S 105 4.1339 160 6.2992 24.75 0.9744 4.5276 6.0630 0.03937
110BTR10S 110 4.3307 170 6.6929 27 1.0630 4.7244 6.4567 0.03937
120BTR10S 120 4.7244 180 7.0866 27 1.0630 5.1181 6.8504 0.03937
130BTR10S 130 5.1181 200 7.8740 31.5 1.2402 5.5118 7.6378 0.03937
rb is housing fillet radius for low shoulder.

216
Super [Link] 1/10/07 3:55 PM Page 37

Common Options
TR : Phenolic cage
TYN : Polyamide cage
DU : Duplex Universal
SU : Single Universal
L : Light Preload
M : Medium Preload
H : Heavy Preload
P4 : ISO 4 (ABEC 7) Precision
P5 : ISO 5 (ABEC 5) Precision

Preload Axial
Limiting Speed Bearing Rigidity
Basic Load Ratings Weight Value
Part Duplex Duplex Duplex
(lbs) (RPM) (Approx.)
Number (EL) (EL)
Cr Cor Grease Oil lbs lbs lbs/.001 inch
60BTR10S 5036 9779 8 400 11 000 0.93 83.18 1884300
65BTR10S 5193 10566 7 900 10 400 0.99 87.68 1998500
70BTR10S 7194 14163 7 300 9 500 1.32 87.68 1998500
75BTR10S 7306 14725 6 900 9 000 1.40 89.92 2055600
80BTR10S 8543 17535 6 400 8 300 1.93 114.65 2284000

85BTR10S 8655 18322 6 100 8 000 2.14 116.90 2398200

90BTR10S 11240 23605 5 700 7 400 2.64 119.15 2455300
95BTR10S 11465 24729 5 500 7 100 2.91 123.64 2569500
100BTR10S 11578 25628 5 200 6 800 3.08 125.89 2626600

105BTR10S 13151 29450 5 000 6 500 3.84 128.14 2683700

110BTR10S 14837 33272 4 700 6 100 4.65 130.39 2797900
120BTR10S 15287 35969 4 400 5 700 4.99 137.13 2969200
130BTR10S 19334 43838 4 000 5 200 7.41 137.13 2969200
Cr = Dynamic Radial Load Rating
Cor = Static Radial Load Rating

217
Super [Link] 1/10/07 3:55 PM Page 38

Super Precision
Cylindrical
Roller Bearings
N 1000 Series
Single Row

Basic Bearing Dimensions Preferred Shoulder Dimensions

Bearing ra da Db
d D B (inch)
Number (inch) (inch)
mm mm mm inch mm inch max max min max
N1006 30 1.1811 55 2.1654 13 0.5118 0.0197 1.3780 2.0079 1.9291
N1007 35 1.3780 62 2.4409 14 0.5512 0.0197 1.5748 2.2835 2.2047
N1008 40 1.5748 68 2.6772 15 0.5906 0.0236 1.7717 2.5197 2.4409
N1009 45 1.7717 75 2.9528 16 0.6299 0.0236 1.9685 2.7953 2.6772

N1010 50 1.9685 80 3.1496 16 0.6299 0.0236 2.1654 2.9921 2.8740

N1011 55 2.1654 90 3.5433 18 0.7087 0.0394 2.4213 3.3465 3.2283
N1012 60 2.3622 95 3.7402 18 0.7087 0.0394 2.6181 3.5433 3.4252
N1013 65 2.5591 100 3.9370 18 0.7087 0.0394 2.8150 3.7402 3.6220

N1014 70 2.7559 110 4.3307 20 0.7874 0.0394 3.0118 4.1339 3.9764

N1015 75 2.9528 115 4.5276 20 0.7874 0.0394 3.2087 4.3307 4.1732
N1016 80 3.1496 125 4.9213 22 0.8661 0.0394 3.4055 4.7244 4.5276
N1017 85 3.3465 130 5.1181 22 0.8661 0.0394 3.6024 4.9213 4.7244

N1018 90 3.5433 140 5.5118 24 0.9449 0.0394 3.8583 5.2559 5.0787

N1019 95 3.7402 145 5.7087 24 0.9449 0.0394 4.0551 5.4528 5.2756
N1020 100 3.9370 150 5.9055 24 0.9449 0.0394 4.2520 5.6496 5.4724
N1021 105 4.1339 160 6.2992 26 1.0236 0.0394 4.4882 6.0433 5.7874

N1022 110 4.3307 170 6.6929 28 1.1024 0.0394 4.6850 6.4370 6.1811
N1024 120 4.7244 180 7.0866 28 1.1024 0.0394 5.0787 6.8307 6.5748
N1026 130 5.1181 200 7.8740 33 1.2992 0.0394 5.4724 7.6181 7.2441
N1028 140 5.5118 210 8.2677 33 1.2992 0.0394 5.8661 8.0118 7.6378

Application Data
Radial Internal Clearance –– Table 10.37 on page 331
Bearing Tolerances –– Table 10.12 thru Table 10.16 on page 314-17
Shaft & Housing Fits –– Contact NSK Engineering

218
Super [Link] 1/10/07 3:55 PM Page 39

Common Options
M : One piece brass cage; inner ring guided
MB : Split type brass cage; roller guided
MR : Riveted brass cage; roller guided
T : Polyamide cage; roller guided
KR : Precision Tapered Bore 1:12
CCx : Matched Clearance (9,1, . . .)
P4 : ISO 4 (ABEC7) Precision

Bearing
Basic Load Ratings Limiting Speeds Weight
Bearing (lbs) (1000 RPM) (Approx.)
Number
Cr Cor Grease Oil lbs
N1006 4400 4400 20.0 22.0 0.29
N1007 5100 5200 18.0 20.0 0.40
N1008 6100 6500 16.0 18.0 0.49
N1009 7300 8000 14.0 16.0 0.60

N1010 7300 8200 13.0 15.0 0.64

N1011 8500 9800 12.0 13.0 0.96
N1012 9000 10900 11.0 12.0 1.02
N1013 9300 11500 10.0 12.0 1.10

N1014 13100 15900 9.5 11.0 1.49

N1015 13400 16800 9.0 10.0 1.58
N1016 16300 20400 8.5 9.5 2.09
N1017 16800 21500 8.0 9.0 2.19

N1018 19800 25800 7.5 8.5 2.86

N1019 20400 27100 7.1 8.0 3.01
N1020 20900 28200 6.7 7.5 3.15
N1021 24500 33500 6.3 7.1 3.98

N1022 29500 39000 6.0 6.7 4.95

N1024 31100 43000 5.6 6.3 5.24
N1026 38600 53500 5.3 5.6 7.94
N1028 39500 56000 4.8 5.3 8.38
Cr = Dynamic Radial Load Rating
Cor = Static Radial Load Rating

219
Super [Link] 1/10/07 3:55 PM Page 40

Super Precision
Cylindrical
Roller Bearings
NN 3000 Series
Double Row

Basic Bearing Dimensions Preferred Shoulder Dimensions

Bearing ra da Db
d D B (inch)
Number (inch) (inch)
mm mm mm inch mm inch max max min max
NN3005 25 0.9843 47 1.8504 16 0.6299 0.0236 1.1417 1.6929 1.6535
NN3006 30 1.1811 55 2.1654 19 0.7480 0.0394 1.3780 1.9685 1.9685
NN3007 35 1.3780 62 2.4409 20 0.7874 0.0394 1.5748 2.2441 2.2047
NN3008 40 1.5748 68 2.6772 21 0.8268 0.0394 1.7717 2.4803 2.4409

NN3009 45 1.7717 75 2.9528 23 0.9055 0.0394 1.9685 2.7559 2.7165

NN3010 50 1.9685 80 3.1496 23 0.9055 0.0394 2.1654 2.9528 2.9134
NN3011 55 2.1654 90 3.5433 26 1.0236 0.0394 2.4213 3.2874 3.2677
NN3012 60 2.3622 95 3.7402 26 1.0236 0.0394 2.6181 3.4843 3.4646

NN3013 65 2.5591 100 3.9370 26 1.0236 0.0394 2.8150 3.6811 3.6614

NN3014 70 2.7559 110 4.3307 30 1.1811 0.0394 3.0118 4.0748 4.0157
NN3015 75 2.9528 115 4.5276 30 1.1811 0.0394 3.2087 4.2717 4.2126
NN3016 80 3.1496 125 4.9213 34 1.3386 0.0394 3.4055 4.6654 4.5276

NN3017 85 3.3465 130 5.1181 34 1.3386 0.0394 3.6024 4.8622 4.7244

NN3018 90 3.5433 140 5.5118 37 1.4567 0.0591 3.8583 5.1969 5.0787
NN3019 95 3.7402 145 5.7087 37 1.4567 0.0591 4.0551 5.3937 5.2756
NN3020 100 3.9370 150 5.9055 37 1.4567 0.0591 4.2520 5.5906 5.4724

NN3021 105 4.1339 160 6.2992 41 1.6142 0.0787 4.4882 5.9449 5.8268
NN3022 110 4.3307 170 6.6929 45 1.7717 0.0787 4.6850 6.3386 6.1811
NN3024 120 4.7244 180 7.0866 46 1.8110 0.0787 5.0787 6.7323 6.5748
NN3026 130 5.1181 200 7.8740 52 2.0472 0.0787 5.4724 7.5197 7.2835

NN3028 140 5.5118 210 8.2677 53 2.0866 0.0787 5.8661 7.9134 7.6772
NN3030 150 5.9055 225 8.8583 56 2.2047 0.0787 6.3386 8.4252 8.2283
NN3032 160 6.2992 240 9.4488 60 2.3622 0.0787 6.7323 9.0157 8.7402
NN3034 170 6.6929 260 10.2362 67 2.6378 0.0787 7.1260 9.8031 9.4094

NN3036 180 7.0866 280 11.0236 74 2.9134 0.0787 7.5197 10.5906 10.1575
NN3038 190 7.4803 290 11.4173 75 2.9528 0.0787 7.9134 10.9843 10.5512
NN3040 200 7.8740 310 12.2047 82 3.2283 0.0787 8.3071 11.7717 11.2205

Application Data
Radial Internal Clearance –– Table 10.37 on page 331
Bearing Tolerances –– Table 10.12 thru Table 10.16 on page 314-17
Shaft & Housing Fits –– Contact NSK Engineering

220
Super [Link] 1/10/07 3:55 PM Page 41

Common Options
M : One piece brass cage; inner ring guided
MB : Split type brass cage; roller guided
MR : Riveted brass cage; roller guided
T : Polyamide cage; roller guided
KR : Precision Tapered Bore 1:12
CCx : Matched Clearance (9,1, . . .)
E44 : Lube Groove and Holes, Outer Ring
P4 : ISO 4 (ABEC7) Precision

Bearing
Basic Load Ratings Limiting Speeds Weight
Bearing (lbs) (1000 RPM) (Approx.)
Number
Cr Cor Grease Oil lbs
NN3005 5800 6700 19.0 22.0 0.28
NN3006 6900 8400 16.0 19.0 0.43
NN3007 8800 11200 14.0 16.0 0.56
NN3008 9700 12500 13.0 15.0 0.67

NN3009 11700 15400 12.0 13.0 0.88

NN3010 11900 16300 11.0 12.0 0.95
NN3011 15500 21700 9.5 11.0 1.40
NN3012 16400 23800 9.0 10.0 1.50

NN3013 17300 26000 8.5 9.5 1.61

NN3014 21900 33300 8.0 9.0 2.31
NN3015 21800 34000 7.5 8.5 2.42
NN3016 26900 41900 6.7 8.0 3.37

NN3017 28200 45200 6.7 7.5 3.54

NN3018 32200 51100 6.0 7.1 4.53
NN3019 33700 55300 6.0 6.7 4.73
NN3020 35300 59500 5.6 6.3 4.95

NN3021 44500 73000 5.3 6.0 6.27

NN3022 51500 84000 5.0 5.6 8.10
NN3024 54000 91000 4.8 5.3 8.82
NN3026 64000 107000 4.3 4.8 12.87

NN3028 67200 116000 4.0 4.5 13.93

NN3030 75000 132000 3.8 4.3 16.92
NN3032 84000 149000 3.6 4.0 20.55
NN3034 101000 181000 3.2 3.8 28.16

NN3036 127000 225000 3.0 3.4 36.74

NN3038 133000 242000 3.0 3.4 38.94
NN3040 147000 262000 2.8 3.2 49.72
Cr = Dynamic Radial Load Rating
Cor = Static Radial Load Rating

221
Super [Link] 1/10/07 3:55 PM Page 42

Super Precision
Cylindrical
Roller Bearings
NN 3900 Series
Double Row

Basic Bearing Dimensions Preferred Shoulder Dimensions

Bearing ra da Db
d D B (inch)
Number (inch) (inch)
mm inch mm inch mm inch max max min max
NN3920 100 3.9370 140 5.5118 30 1.1811 0.0394 4.1929 5.2559 5.1575
NN3921 105 4.1339 145 5.7087 30 1.1811 0.0394 4.3898 5.4528 5.3543
NN3922 110 4.3307 150 5.9055 30 1.1811 0.0394 4.5866 5.6496 5.5512
NN3924 120 4.7244 165 6.4961 34 1.3386 0.0394 4.9803 6.2402 6.0827

NN3926 130 5.1181 180 7.0866 37 1.4567 0.0591 5.4331 6.7717 6.6535
NN3928 140 5.5118 190 7.4803 37 1.4567 0.0591 5.8268 7.1654 7.0866
NN3930 150 5.9055 210 8.2677 45 1.7717 0.0787 6.2598 7.9134 7.7559
NN3932 160 6.2992 220 8.6614 45 1.7717 0.0787 6.6535 8.3071 8.1496

NN3934 170 6.6929 230 9.0551 45 1.7717 0.0787 7.0472 8.7008 8.5433
NN3936 180 7.0866 250 9.8425 52 2.0472 0.0787 7.4409 9.4882 9.2126
NN3938 190 7.4803 260 10.2362 52 2.0472 0.0787 7.8346 9.8819 9.6654
NN3940 200 7.8740 280 11.0236 60 2.3622 0.0787 8.3071 10.5906 10.2756

NN3944 220 8.6614 300 11.8110 60 2.3622 0.0787 9.0945 11.3780 11.0630
NN3948 240 9.4488 320 12.5984 60 2.3622 0.0787 9.8819 12.1654 11.8898
NN3952 260 10.2362 360 14.1732 75 2.9528 0.0787 10.6693 13.7402 13.3071
NN3956 280 11.0236 380 14.9606 75 2.9528 0.0787 11.4567 14.5276 14.0945

Application Data
Radial Internal Clearance –– Table 10.37 on page 331
Bearing Tolerances –– Table 10.12 thru Table 10.16 on page 314-17
Shaft & Housing Fits –– Contact NSK Engineering

222
Super [Link] 1/10/07 3:55 PM Page 43

Common Options
M : One piece brass cage; inner ring guided
MB : Split type brass cage; roller guided
MR : Riveted brass cage; roller guided
T : Polyamide cage; roller guided
KR : Precision Tapered Bore 1:12
CCx : Matched Clearance (9,1, . . .)
E44 : Lube Groove and Holes, Outer Ring
P4 : ISO 4 (ABEC7) Precision

Bearing
Basic Load Ratings Limiting Speeds Weight
Bearing (lbs) (1000 RPM) (Approx.)
Number
Cr Cor Grease Oil lbs
NN3920 23800 40800 6.0 6.7 2.84
NN3921 24700 43600 5.6 6.3 3.30
NN3922 25800 46500 5.3 6.3 3.43
NN3924 30900 56000 5.0 5.6 4.40

NN3926 39000 72500 4.5 5.3 5.65

NN3928 45200 85000 4.3 4.8 6.07
NN3930 59000 109000 3.8 4.5 9.77
NN3932 61000 117000 3.6 4.3 11.33

NN3934 63000 123000 3.6 4.0 12.03

NN3936 76000 148000 3.2 3.8 15.71
NN3938 77000 152000 3.2 3.6 16.35
NN3940 93500 184000 3.0 3.4 23.10

NN3944 99000 202000 2.6 3.0 25.08

NN3948 104000 218000 2.6 2.8 26.62
NN3952 151000 311000 2.2 2.6 47.08
NN3956 155000 328000 2.2 2.4 49.94
NN3920 23800 40800 6.0 6.7 2.84
NN3921 24700 43600 5.6 6.3 3.30
NN3922 25800 46500 5.3 6.3 3.43
NN3924 30900 56000 5.0 5.6 4.40
Cr = Dynamic Radial Load Rating
Cor = Static Radial Load Rating

223
Super [Link] 1/10/07 3:55 PM Page 44

Ball Screw
Support Bearings
Major Dimensions

Inch Series
Boundary Dimensions
Bearing Bore Diameter Outside Diameter Ball
d D Width B Complement
Number
mm inch mm inch mm inch no.- inch
20 TAC 47XB 20.000 0.7874 47.0 1.8504 15.875 0.6250 15–1/4
23 TAC 62B 23.838 0.9385 62.0 2.4409 15.875 0.6250 21–1/4
38 TAC 72B 38.100 1.5000 72.0 2.8346 15.875 0.6250 24–1/4
44 TAC 76B 44.475 1.7510 76.2 3.0000 15.875 0.6250 26–1/4

57 TAC 90B 57.150 2.2500 90.0 3.5433 15.875 0.6250 32–1/4

76 TAC 110B 76.200 3.0000 110.0 4.3307 15.875 0.6250 41–1/4
101 TAC 145B 101.600 4.0000 145.0 5.7087 22.225 0.8750 37–3/8

Metric Series
Boundary Dimensions
Bearing Bore Diameter Outside Diameter Ball
d D Width B Complement
Number
mm inch mm inch mm inch no.- inch
17 TAC 47B 17 0.6693 47 1.8504 15 0.5906 15–1/4
20 TAC 47B 20 0.7874 47 1.8504 15 0.5906 15–1/4
25 TAC 62B 25 0.9843 62 2.4409 15 0.5906 21–1/4
30 TAC 62B 30 1.1811 62 2.4409 15 0.5906 21–1/4

35 TAC 72B 35 1.3780 72 2.8346 15 0.5906 24–1/4

40 TAC 72B 40 1.5748 72 2.8346 15 0.5906 24–1/4
40 TAC 90B 40 1.5748 90 3.5433 20 0.7874 20–1/4
45 TAC 75B 45 1.7717 75 2.9528 15 0.5906 26–1/4

45 TAC 100B 45 1.7717 100 3.9370 20 0.7874 23–3/8

50 TAC 100B 50 1.9685 100 3.9370 20 0.7874 23–3/8
55 TAC 100B 55 2.1654 100 3.9370 20 0.7874 23–3/8
55 TAC 120B 55 2.1654 120 4.7244 20 0.7874 27–3/8

60 TAC 120B 60 2.1654 120 4.7244 20 0.7874 27–3/8

224
Super [Link] 1/10/07 3:55 PM Page 45

Ball Screw
Support Bearings
Load Ratings

Inch Series
Dynamic Axial Load Rating Ca Limited Axial Capacity
Bearing One Row Two Rows Three Rows Two Rows Three Rows
Loaded Loaded One Row Loaded Loaded
Number Loaded Loaded DF
DF DFD•DFF•DT DFT•DTD DFD•DFF•DT DFT•DTD
daN lbf daN lbf daN lbf daN lbf daN lbf daN lbf
20 TAC 47XB 2190 4920 3550 7980 4750 10700 2660 5980 5300 11900 7950 17900
23 TAC 62B 2850 6410 4650 10500 6150 13800 4050 9110 8150 18300 12200 27400
38 TAC 72B 3150 7080 5150 11600 6850 15400 5200 11700 10400 23400 15700 35300
44 TAC 76B 3300 7420 4350 12000 7100 16000 5700 12800 11400 25600 17000 38200

57 TAC 90B 3550 7980 5750 12900 7600 17100 6850 15400 13700 30800 20500 46100
76 TAC 110B 3900 8770 6300 14200 8350 18800 8650 19400 17300 38900 26000 58500
101 TAC 145B 7600 17100 12300 27700 16400 36900 16600 37300 33000 74200 50000 112000

Metric Series
Dynamic Axial Load Rating Ca Limited Axial Capacity
Bearing One Row Two Rows Three Rows Two Rows Three Rows
Loaded Loaded One Row Loaded Loaded
Number Loaded Loaded DF
DF DFD•DFF•DT DFT•DTD DFD•DFF•DT DFT•DTD
daN lbf daN lbf daN lbf daN lbf daN lbf daN lbf
17 TAC 47B 2190 4920 3550 7980 4750 10700 2660 5980 5300 11900 7950 17900
20 TAC 47B 2190 4920 3550 7980 4750 10700 2660 5980 5300 11900 7950 17900
25 TAC 62B 2850 6410 4650 10500 6150 13800 4050 9110 8150 18300 12200 27400
30 TAC 62B 2920 6570 4750 10700 6300 14200 4300 9670 8600 19300 12900 29000

35 TAC 72B 3100 6970 5050 11400 6700 15100 5000 11200 10000 22500 15000 33700
40 TAC 72B 3150 7080 5150 11600 6850 15400 5200 11700 10400 23400 15700 35300
40 TAC 90B 5900 1330 9550 21500 12700 28600 8950 20100 17900 40200 26900 60500
45 TAC 75B 3300 7420 5350 12000 7100 16000 5700 12800 11400 25600 17000 38200

45 TAC 100B 6150 13800 10000 22500 13300 29900 9900 22300 19800 44500 29800 67000
50 TAC 100B 6300 14200 10200 22900 13600 30600 10400 23400 20800 46800 31000 69700
55 TAC 100B 6300 14200 10200 22900 13600 30600 10400 23400 20800 46800 31000 69700
55 TAC 120B 6750 15200 10900 24500 14500 32600 12300 27700 24600 55300 37000 83200

60 TAC 120B 6750 15200 10900 24500 14500 32600 12300 27700 24600 55300 37000 83200

225
Super [Link] 1/10/07 3:55 PM Page 46

Ball Screw
Support Bearings
Preloads

Inch Series (Preload Symbol C11)

Duplex Triplex Quadruplex
Combinations Combinations Combinations
Bearing (DF) (DFD) (DFF)
Number Preload Preload Preload
lbf lbf lbf
20 TAC 47XB 750 1000 1500
23 TAC 62B 1000 1350 2000
38 TAC 72B 1500 2100 3000
44 TAC 76B 1500 2100 3000

57 TAC 90B 1750 2300 3500

76 TAC 110B 2250 3000 4500
101 TAC 145B 3000 4100 6000

Metric Series (Preload Symbol C10)

Duplex Triplex Quadruplex
Combinations Combinations Combinations
Bearing (DF) (DFD) (DFF)
Number Preload Preload Preload
lbf lbf lbf
17 TAC 47B 490 680 990
20 TAC 47B 490 680 990
25 TAC 62B 680 930 1390
30 TAC 62B 680 930 1390

35 TAC 72B 790 1080 1590

40 TAC 72B 790 1080 1590
40 TAC 90B 1010 1390 2050
45 TAC 75B 790 1080 1590

45 TAC 100B 1170 590 2300

50 TAC 100B 1170 1590 2300
55 TAC 100B 1170 1590 2300
55 TAC 120B 1390 1870 2750

60 TAC 120B 1390 1870 2750

226
Super [Link] 1/10/07 3:55 PM Page 47

Notes

227