SIGNAGE

REQUIREMENTS

F45 TRAINING
GLOBAL

2019
 CONTENTS

1. INTRODUCTION 3
2. SIGNAGE REQUIREMENTS 4
3. COLOUR SCHEMES & PAINT COLOURS 7

SIGNAGE 4. INTERNAL SIGNAGE 9

REQUIREMENTS
5. INSTALLATION OF INTERNAL SIGNAGE 14
6. EXTERNAL SIGNAGE 16
7. ADDITIONAL SIGNAGE & BRANDING 19

GLOBAL 8. EXAMPLES OF WHAT IS NOT ALLOWED IN YOUR STUDIO 27

9. ANNEXURE A - GLOSSARY OF TERMS 29

4 8
INTRODUCTION

What is this document?

This Document sets out details of your obligations as a F45 Franchisee, and provides information that is referred to in your Agreement and the
Operations Manual. In particular, this Document sets out important information regarding the installation and overall appearance of your Studio.

Updates to this Document

This Document will be updated from time to time as the need arises. We encourage you to keep up to date with the policies and procedures on the F45
Intranet, which are accessible via F45Playbook.com. Where we make an amendment or otherwise update the requirements set out in this Document,
we will provide you with a reasonable amount of time to effect any changes required for your Studio.

Policies and Guidance

Parts of this Document provides guidance, while other parts set out policies and procedures that you are required to follow as part of your
Agreement with F45. If the Document says you must do something or uses similar words, this is a requirement rather than a guideline, and you
are expected to comply with the requirement. Failure to do so may be a breach of your Agreement, which if not remedied, could lead to the
termination of the Agreement.

Your Obligations
You have various obligations under the terms of your Agreement, this Document and other policies and procedures introduced by F45 from time to
time. You must familiarise yourself with your obligations under each of those documents.

We reserve the right to ask you for information, documents and or receipt to verify your compliance with your obligations under this Document or your
Agreement. If requested, within the time specified (if any) or, if no time is specified, as soon as possible.

If you have failed to comply with your obligations under the Agreement or this Document, we may request you to do anything or act which we believe
is necessary (acting reasonably) to comply with your obligations.

Compliance with this Document

You must strictly observe the requirements set out in this Document, unless you obtain the prior written approval of F45.
3
INTRODUCTION

Getting Advice
We are here to assist with general advice on requirements for your franchise, however Advice and information within this Document cannot be relied
upon on or substituted for professional advice. Remember that every franchise is individually responsible for its business decisions and its legal tax and
accounting obligations. You should seek independent professional advice about these matters as needed.

Confidentiality
This Document is provided to the Franchisee and is a confidential document. You are required to keep it confidential except where the law allows
sharing. All the information in these documents is protected by copyright laws. It is not to be reproduced in whole or in part without the prior written
consent of F45. In managing your business, you will consult with your own lawyers, accountants and business advisers. In these instances, you have
permission to discuss these documents but none of the material may be copied by you or your advisers.

Ownership
This Document is on loan to the franchisee and is the property of F45 Group. It is on loan for the term of the Agreement. Any reproduction of this manual
is not possible without the prior written approval of F45. If your business finishes you must return this manual, along with any amendments, to F45.

Policies & Requirements

This Document does not set out the totality of your obligations. You must also adhere to any other policy or requirement implemented by F45 from
time to time.

Inconsistency with your Agreement

In the event that there is an inconsistency with the terms of this Document and the terms of your Agreement, the terms of your Agreement will prevail
to the extent of the inconsistency.

Interpretation
Unless indicated otherwise, capitalised term in this Document have the meaning given to them in Annexure A.

4
SIGNAGE REQUIREMENTS

F45 has strict signage requirements that relate to:

• Internal signage, that is the signage that appears inside your Studio (Internal Signage);

• External signage, that is signage that appears outside of your Studio including motor vehicles and alike (External Signage).

These requirements are set out in this Document.

Following directions from F45

Your Internal Signage and External Signage will vary depending upon the set up and layout of your Studio. F45 has the right, at its absolute discretion,
to determine the design, layout and the type of signage that needs to be installed in your Studio.
You will be required to submit to F45 your proposal for Internal Signage and External Signage for approval. You must follow any directions or requests
given to you by F45 in relation to the modification of your proposals.

Signage Approval
All signage inside and outside of your Studio must be approved by F45. You must obtain this approval prior to the installation or erection of any
signage. Once you have obtained this approval you must not alter or modify the signage in any manner and must ensure that the installation of the
signage strictly accords with the terms of the approval from F45. If your signage does not accord with that approval, your Studio will not be approved
to open.

Use a Professional
We highly recommend that you use a professional signage installer for your Internal and External Signage.

Sourcing of Signage
Usually, F45 will supply Internal Signage. If F45 supplies Internal Signage, you must use that signage for your Studio and must not source any other
signage. Additionally, you must not seek to have the Internal Signage painted on the walls, without the prior written approval of F45 (which will only be
granted in exceptional circumstances, as determined by F45). You are responsible for sourcing (and paying for) your External Signage, as these items
are not usually supplied by F45.

5
SIGNAGE REQUIREMENTS

Internal Signage Process

Once your site has been approved, you may submit your proposal for internal signage to F45 at any time, however we recommend that you wait until
your floorplan has been approved before you submit any proposal. Your proposal for Internal Signage must:

• be in a single document (either a PDF or PowerPoint presentation);

• show the walls the signage is to be applied to (in a photograph), with the proposed signage overlaid on top of the relevant image;

• show the measurements for the signage, so F45 can verify that the Internal Signage will be installed in accordance with its specifications; and

• include any additional details requested by F45 from time to time.

If you have engaged the services of a professional signage installer (which we recommend), they will usually be able to assist you in the process as a
part of their service.

External Signage
Your External Signage will vary depending on your Studio. You can submit your proposal for External Signage as soon as your site has been approved.
Your proposal for External Signage must:

• be in a single document (either a PDF or PowerPoint presentation);

• show the exterior surface of the Premises (in a photograph), with the proposed signage overlaid on top of the relevant image;

• show the measurements for the signage, so F45 can verify that the External Signage will be installed in accordance with its specifications; and

• include any additional details requested by F45 from time to time.

For external signage, you must engage the services of a professional signage installer, as you are required to source this signage separate to the goods
and equipment supplied by F45. Your External Signage supplier will usually be able to assist you with your submission of External Signage.

Modifications or alterations to signage

Once your signage has been installed you must not alter or modify the signage or install additional signage without our prior written approval. If you
making any such modification, you will be deemed to be in breach of your Agreement until such time that you rectify to F45’s satisfaction.
6
SIGNAGE REQUIREMENTS

Set out below is an example of how your submission for External Signage should look.

OVERALL SHOPFRONT WIDTH

AREA AVAILABLE FOR SIGNAGE

OVERALL SHOPFRONT HEIGHT

OVERALL SIZES

EACH WINDOWS PARTITION WIDTH AND HEIGHT

EACH GLASS DOOR WIDTH AND HEIGHT

OVERALL SHOPFRONT WIDTH

AREA AVAILABLE FOR SIGNAGE

OVERALL SHOPFRONT HEIGHT

OVERALL SIZES

SITE ELEVATION DRAWINGS

EACH WINDOWS PARTITION WIDTH AND HEIGHT

EACH GLASS DOOR WIDTH AND HEIGHT

SITE PHOTO WITH MEASUREMENTS

7
COLOUR SCHEMES & PAINT COLOURS

Set out below are the colour schemes used in F45 Studios. You must strictly adhere to these colour schemes and you must not modify those colours in
any manner.

Primary Colours Secondary Colours

ral : 9003 signal white pantone : BLACK

CMYK : 0.0.0.0 CMYK : 0.0.0.100
RGB : 255.255.255 RGB : 0.0.0
hex : #ffffff

ral : 5022 NIGHT BLUE pantone : cool GREY 10c

pantone : 274 c CMYK : 0.0.0.75
CMYK : 100.100.7.38 RGB : 100.100.100
RGB : 33.21.81
hex : #211551
pantone : 70% 2766 c
ral : 3020 pure red CMYK : 77.74.27.2
pantone : 2035 c RGB : 88.87.133
CMYK : 0.100.100.3
RGB : 214.0.28
hex : #D6001C

8
COLOUR SCHEMES & PAINT COLOURS

Paint Codes
The entire interior of a F45 Studio must be painted white, including the walls (from floor to ceiling), internal doors and also the ceiling, unless you have
obtained the prior written approval of F45. You do not need to paint the windows.
We set out below the paint codes for 4 of the top paint brands. Please refer to these paint codes when purchasing wall paint.

Recommended White Paints

DULUX SILK BRITISH PAINTS

30GY 88/014 | White on White 5W W1 | Love Note

Recommended Red Paints

DULUX TAUBMANS BRITISH PAINTS SHERWIN WILLIAMS

16YR 16/594 | Matador T12 25.H1 | Hi-C Red 186 | Red Bauble SW 6868 | Real Red

Recommended Cobalt Blue Paints

DULUX TAUBMANS BRITISH PAINTS SHERWIN WILLIAMS

DLX1174-7 | Royal Indigo 34CB-3 | Egyptian Violet 276 | Midnight Whirlwind SW 6545 | Majestic Purple 9
INTERNAL SIGNAGE

Requirements
Set out below are the requirements for Internal Signage for your Premises. The precise design of your Internal Signage will be determined by F45 once
you submit your proposal, however your Internal Signage must strictly accord with these measurements.

Standard Size
3000mmW x 2225mmH
Suitable for ceiling
heights: 2600mmH -
3350mmH FFL

Large Size
3890 x 2900mmH
Suitable for ceiling
heights: 3351mmH -
4350mmH FFl

Extra Large Size

5000mmW x 3729mmH
Suitable for Ceiling
heights: 4351mmH + FFL

88.5

10
INTERNAL SIGNAGE

Set out below is an example of how your Internal Signage will look when installed.

WD-STR
WALL RACING STRIPE DECAL
WD-STR-CL To be installed to all walls (apart from
COLUMN RACING STRIPE DECAL the large logo wall) at 700mm FFL.
To be installed to columns at 700mm
FFL. One star to be installed to each
side of column, centred to each face.
ILL-FEAT / WD-FEARFEATURE LOGO WD-TAG
ILLUMINATED / DECAL WALL TAG LINE DECAL
To be installed on the wall indicated in To be installed to blue section of
Columns to be painted
your approved floor plan mock up, The logo needs to be placed wall racing stripe decals centred
to match PMS 534 C
unobstructed by equipment, power 30cm from the ground to the to wall.
points, etc. base of the logo.
Corner
CL

Based on
2600mm
(8.6”)
Wall Height

Install
700mm
(27.6”)
FFL

PAGE NAME HERE - SCALE 1:x PAGE NA

11
INTERNAL SIGNAGE

Internal Wall Logo

Every Studio must feature an internal wall logo (Wall Logo). The Wall Logo is
INTERIOR SIGNAGE - WALL LOGO 25
a very important part of the signage and the main branding element for the
All walls and ceilings must be painted white. large interior logo cannot be on the same wall as
Studio interior. When you submit your Internal Signage submission, you must any Tv’s and cannot have racing stripes on this wall. 2 metre gap if need be. The wall logo must
provide the wall dimension, as the Wall Logo must: fill 85% of the height of the wall. Dimensions must be included in submissions to HQ. No interior
signage will be approved if it is not dye cut. Surface needs to be dry wall, rendered, flat brick
(with no mortar lines) and if this is not possible then please seek advice from Hq.
• encompass at least 85% of the relevant wall; Studio Interior - Wall logo vinyl
• be positioned 30cms from the floor to the base of the Wall Logo;
• be centered on the wall and it must not have any equipment
obscuring it from view;
• not be on the same wall as a TV; and
• not be on a same wall as the internal racing stripes, or there must
be a clear 2 metre distance between the edge of the Wall Logo
and the beginning of any internal racing stripe.

The wall logo must fill 85% of the height of the wall.

The wall logo must fill 85% of the height of the wall.

Do not put items in front of the wall logo logo must be centered on the wall in the
Do not put items in front of correct dimensions
the wall logo.
E: [email protected] www.f45training.com

12
INTERNAL SIGNAGE

Internal Wall Racing Stripes

Except for the wall which features the Wall Logo, all walls must have racing
stripes, however only 2 walls may have the slogan ‘Team Training. Life Changing’ 70CM / 27.5” FROM THE FLOOR

(Slogan).

Where featured, the Slogan must be centered to the wall and printed once only.
All racing stripes must be 70cm/27.5” from the ground.

13
INTERNAL SIGNAGE
The Blue star =60mm x 60mm

Internal Pylon Racing Stripes

The internal pylons in your Studio (if any) must be painted blue in accordance
The combined heigh
with our specifications, which include: 70CM / 27.5” FROM THE FLOOR of stripes = 25cm
Top white stripe = 75% Bottom red stripe = 25%

• the blue star must be centered on the pylon; and From the ground to the
bottom of red stripe = 70cm
• all racing stripes must be 70cm/27.5” from base of the stripe to the ground.
E: [email protected] www.f45training.com

14
INSTALLATION OF INTERNAL SIGNAGE

Engage a Professional Signage Installer

We highly recommend that you engage the services of a suitably qualified
USA KILZ
signage professional to install the signage in your studio. The F45 Internal
PREMIUM PRIMER
Signage is “high tack”, which means that once you affix it to the wall, you will not
be able to reposition the signage. If you install the signage and then attempt to
reposition, it will void any warranty claim associated with the internal signage
and may:

• damage the internal signage; and/or EU ZINSSER

BULLS EYE 1 2 3
• damage the internal walls and result in the paint being removed
WATER BASED PRIMER
from that wall.

Prepare The Wall Properly AU DULUX

It is important that the wall surface is adequately prepared prior to attempting 1 STEP PRIMER,
to affix the internal signage to the wall. In order to properly prepare the wall, SEALER AND UNDERCOAT
you (or your installer) must follow the instructions set out below. WATER BASED PRIMER

Clean and Repair

It is essential that you (or your signage installer) cleans and repairs the surface and
inspects for any objects that are likely to impair the application of a primer, paint
or signage. You must ensure that the wall surface is clean, smooth and free of
bumps or debris. The internal signage is a thin layer of PVC film and so any debris
or bumps on the application surface will show as bumps on the outer surface
of the sticker or prevent the signage from adhering properly. It is essential that
these be removed and that the wall is clean for a perfect installation.

Wall must be smooth, clean and completely dry before applying primer base
coat. It is recommended that walls have little or no surface variation and a
smooth texture. Repair any wall damage and return walls to ‘like new’ condition.
Walls that are not properly repaired may cause poor graphic adhesion. 15
INSTALLATION OF INTERNAL SIGNAGE

Examples of unsound walls include those with cracks, damaged or inconsistent surfaces, holes, incomplete patches, loose wall-board joints, overly
textured paint, moist, chipped, loose, flaking or peeling paint.

If the walls are flat brick with no mortar lines this is acceptable. In instances where it is not possible to achieve a flat brick finish please contact F45.
Moisture behind wall-board may cause the wall-board paper to release. Pay special attention to areas where condensation may occur, including walls
around cooling units, overhead windows or water pipes that could drip on the graphic.

Remove any wallpaper not securely bonded to walls. Do not apply the graphic over wallpaper, it won’t stick. Painting over wet or damp drywall compound
will retard paint drying and cause inconsistent graphic adhesion. Painting over dusty drywall will impair primer bond to wall surface.

Use a Primer
Our recommended primers are set out below. Primer should be allowed to dry for a minimum of 3 days.

Using The Correct Paint

It is essential that the wall surface be painted with a teflon free paint. Teflon is a component added to the paints to give it a “wash and wear” feature.
If you are unsure which paint to use, we recommend that you consult with a professional paint store or contact an experienced painter for their
recommended paints that are interior low sheen paints, without any barrier technology. In addition to the above, you should have regard to the
requirements set out below.

• Not all latex paints will be compatible with pressure sensitive adhesive (especially zero/low voc paints). Vinyl film should be tested in an
inconspicuous area to ensure that an adequate bond develops over 24 hours.
• No installation should take place until media and paint are deemed compatible.
• The end-user/applicator is responsible for ensuring all painted substrates have been processed and cured according to the paint
manufacturer’s specifications. Failure to follow these specifications may cause loss of adhesion and therefore reduce the vinyl graphic’s
durability and performance. This may lead to graphic failure and/or removal problems.

For the correct colors, please refer to section on paint colors to find the correct code and color reference. Our recommended paints can be seen on
page 7.

16
INSTALLATION OF INTERNAL SIGNAGE

Allow For Cure Period

As outlined above, you must paint the internal walls of your studio as soon as possible in order to allow the paint enough time to ‘cure’. Curing is the
process by which the paint dries, hardens, and releases vapours and solvents contained within the paint, over time. The cure time may vary depending
on how many coats of paint were applied to the relevant surface. However, you must allow the paint to cure for a period of not less than 30 days
prior to installing any adhesive internal signage. If you install signage before the paint has had time to cure, it will stop the curing process thereby
affecting the adhesive and causing the signage to peel.

Vinyl Application
The signage must not be installed until paint has cured.

• Proper cleaning and preparation of the substrate prior to application is critical to the success of the graphic.
• A final cleaning pass prior to painting with a 50% mix of water and IPA will ensure that the paint is dust free and ready for graphic
installation. Once the cleaning mix has dried (+/- 20mins) you may apply the graphics.
• Vinyls must be applied with a plastic squeegee or soft rubber roller being careful to minimize stretch while maximizing pressure.
• Use overlapping squeegee strokes beginning at the centre of the vinyl and extending completely over the edge to ensure the margins
are well attached.
• Margins are frequent sites of failure to attach due to poor initial attachment.

17
EXTERNAL SIGNAGE

Your External Signage will vary depending on your site requirements and will be determined by F45 following receipt of your submission. Set out in this
section is an overview of the External Signage that is available depending on the site.

External Signage Specifications

Set out below are the specifications for External Signage.

CHANNEL LETTERING 400mmH CHANNEL LETTERING 600mmH CHANNEL LETTERING 900mmH

1000mm (39.3”) 1861mm 1000mm (39.3”)
per module (73.3”) per module
1000mm (39.3”) 85mm 1000mm (39.3”) 1000mm (39.3”) 1241mm 1000mm (39.3”)
per module (32.5”) per module per module (48.9”) per module

400mm 900mm
600mm
(15.7”) (53.4”)
(23.6”)

LIGHTBOX FASCIA SIGN 400mmH LIGHTBOX FASCIA SIGN 600mmH LIGHTBOX FASCIA SIGN 900mmH
1000mm (39.3”) 1861mm 1000mm (39.3”)
1000mm (39.3”) 1241mm 1000mm (39.3”) per module (73.3”) per module
1000mm (39.3”) 85mm 1000mm (39.3”)
per module (48.9”) per module
per module (32.5”) per module

400mm 600mm 900mm

(15.7”) (23.6”) (53.4”)

FA-400 FA-600 FA-900

CANTILEVERED LIGHTBOX 1500mmW UNDER AWNING LIGHTBOX 750mmW WALL MOUNTED LIGHTBOX 300mmH WALL MOUNTED LIGHTBOX 1400mmH
CANTILEVERED LIGHTBOX 750mmW 1300mm (51.2”)

1500mm (59”) 600mm (23.6”)

750mm (29.5”) 750mm (29.5”)

300mm 300mm
300mm (11.8”) 1400mm
(11.8”)
(11.8”) (55.1”)

UA-750
CL-1500 CL-750 WM-300 WM-1400

NON-ILLUMINATED BANNER GLAZING LOGO DECAL GLAZING RACING STRIPE DECAL TOWN CENTRE SIGN
1000mm (39.4”) (FOR USE ON PYLONS)
640mm
(25.2”)
400mm (15.7”)
Site specific Site specific

310mm 250mm
1500mm (9.8”) Site
(12.2”)
(59”) specific

BN-1500 GD-LOGO GD-STR TC-PYL TC-PYL-CUS

18
PLEASE NOTE: The sizes indicated above are for guideline purposes only, and will vary by location and
storefront. Please use these as examples, and scale the signage as necessary for your location.
EXTERNAL SIGNAGE

Set out below are the specifications for the External Signage and how that signage will appear during the day. Your External Signage must accord with
these specifications.

FA-600 CL-900 GD-STR

TC-PYL LIGHTBOX FASCIA SIGN 600mmH GLAZING RACING STRIPE DECAL
TOWN CENTRE SIGN CHANNEL LETTERING SIGN 900mmH
To be positioned either above the entry way To be positioned either above the entry To be installed to glazing at 700mm FFL.
For use when there is an existing pylon Stars must be 40cm apart.
sign with space allocated to the F45 ten- doors or across the full length of the building way doors or across the full length of the
ancy. Size and construction are determined fascia depending on the site and visibility. building fascia depending on the site and
on a site by site basis. The racing stripes should extend the full visibility. The racing stripes should extend
length of available space. The logo must be the full length of available space. The logo GD-LOGO
positioned directly above the entry doors. must be positioned directly above the GLAZING LOGO DECAL
WM-1400 entry doors. To be installed to door glazing at 1600mm
WALL MOUNTED LIGHTBOX 1400mmH FFL.
To be used when there is either a 600mmH
fascia or 900mmH fascia installed on the UA-1500 CA-1500
shopfront. It should be positioned on the BN-1500 CANTILEVERED LIGHTBOX 1500mmW
UNDER AWNING LIGHTBOX 1500mmW NON-ILLUMINATED BANNER 1500mmH
side of the building at a high level, prefer- To be positioned close to the entry way To be used when an under awning
ably the 2nd storey, depending on the site To be positioned perpendicular to the lightbox is not suitable for the site, such
doors depending on the site and visibility. building at a high level, preferably the
and visibility. The F45 logo should always be closest to as where there is no awning. The lightbox
2nd storey, depending on the site and should be positioned close to the entry
the kerb. visibility. way doors depending on the site and
CORNER visibility. The F45 logo should always be
closest to the kerb.

1600mm
(63”)
FFL
700mm
(27.6”)
FFL

19
 EXTERNAL SIGNAGE

Set out below is how that signage will appear at night. Your External Signage must accord with these specifications.

GD-STR
GD-STR
GLAZING RACING
GLAZING RACING STRIPE
STRIPE DECAL
DECAL
TC-PYL
TC-PYL FA-600FA-600 CL-900
FA-900
Non-illuminated.
Non-illuminated. Stars must be 40cm apart.
TOWN TOWN CENTRE
CENTRE SIGNSIGN LIGHTBOX
FASCIAFASCIA SIGN 600mmH
SIGN 600mmH FASCIA SIGN
CHANNEL 900mmH
LETTERING SIGN 900mmH
Illumination
Illumination is dependent
is dependent on pylon
on existing F45 logo andand
F45 logo racing
racingstripes
stripes totobebe internally
internally F45 logo
F45 logoand
toracing stripes to be
be internally internally
illuminated.
FL. existing pylon
structure structure
and wil and
be detemined on will
a site be
by site illuminated.
illuminated. illuminated.
GD-LOGO
GD-LOGO
detemined
basis. on a site by site basis. GLAZING LOGO
GLAZING LOGO DECAL
DECAL
Non-illuminated.
Non-illuminated.
WM-1400
WM-1400
s WALL MOUNTED LIGHTBOX 1400mmH UA-1500
UA-1500 BN-1500
BN-1500
WALL MOUNTED LIGHTBOX 1400mmH
UNDERUNDER AWNING
AWNING LIGHTBOX1500mmW
LIGHTBOX 1500mmW NON-ILLUMINATED BANNER
NON-ILLUMINATED BANNER 1500mmH
1500mmH CA-1500
CA-1500
is SignSign
facefaceto
to be internally
be internally illuminated.
illuminated. Both sign
Both sign facesfaces
to tobebeinternally
internally illuminated.
illuminated. Non-illuminated. CANTILEVERED
CANTILEVERED LIGHTBOXLIGHTBOX 1500mmW1500mmW
d Non-illuminated.
he
Both signfaces
Both sign faces tointernally
to be be internally illuminated.
illuminated.
s be
CORNER
CORNER

F45 INDICATIVE SHOPFRONT - NIGHT F45 INDICATIVE SHOPFRONT - NIGHT

ELEVATION Elevation 1 ELEVATION Elevation 2

SCALE 1:50 SCALE 1:50

20
 Station numbering 1 - 27

ADDITIONAL SIGNAGE AND BRANDING

Station Markers 
Station markers are provided in your equipment pack. Only use what we provide. Do not create your own.

Station numbering 1.1 - 9.2

E: [email protected] www.f45training.com
21
ADDITIONAL SIGNAGE AND BRANDING

Banners
Banners have been created and are provided in your equipment pack. Banners are great devices to use when opening a new studio, recruiting new
customers or creating awareness if your studio is not in view of foot traffic on a sidewalk level.

LARGE TEARDROP BANNER SMALL TEARDROP BANNER

307.5cm x 100cm / 121” X 27.5” 86.3cm x 177.8cm / 34” X 70”
Allow for 2” bleed on all sides Allow for 2” bleed on all sides
22
ADDITIONAL SIGNAGE AND BRANDING

A Frames
Artwork has been created for your A-frame signage and has been provided in A-FRAME BACK
your equipment pack. A-frames are great devices to use when opening a new 60cm x 90cm / 23.6” X 35.4”
studio, recruiting new customers or creating awareness if your studio is not in Allow for 0.5cm/1.27”
view of foot traffic on a sidewalk level. You can also use A-frames as internal bleed on all sides
directional signs to direct customers in a building.

A-FRAME FRONT
60cm x 90cm / 23.6” X 35.4”
Allow for 0.5cm/1.27”
bleed on all sides

23
ADDITIONAL SIGNAGE AND BRANDING

Directional Signage
Artwork has been created for directional signage and has been provided in your
equipment pack. Use these signs as internal directional signs to direct customers
once inside a building.

24
ADDITIONAL SIGNAGE AND BRANDING

Desk Design
Only Studios with: (a) a minimum of 180sqm (1937.5sqft) of training floor
space; and (b) 25sqm (269.098sqft) for stretching and waiting space (205sqm
total/2206.6sqft), will be allowed to install a desk. Franchisees are permitted to
source their own materials/installation, but all designs must be approved by HQ
prior to sourcing and installing a desk.

25
ADDITIONAL SIGNAGE AND BRANDING

Desk Dimensions

2000

REAR CARCASS

FRONT CARCASS
900

450

FRONT
BRANDING

ALL OUTER SUFACES TO HAVE JOINS

PLATERED OR SIMILAR BEFORE PAINTING

16
398
DRAWER LENGTH

199

DRAWER DEPTH
B

140
1260
900

60

32

DETAIL B
SCALE 1 : 2
STANDARD
FINGER PULL
32 DETAIL
100 A

SECTION A-A
SCALE 1 : 8

50 DO NOT SCALE OFF DRAWING. DO NOT MAKE ASSUMPTIONS. IF IN DOUBT, ASK.

TOLERANCES UNLESS STATED NOTES: D3 PRODUCT DESIGN PTY LTD

Studio 1, Level 4
35 Buckingham Street
NO DECIMAL (e.g. 25) ±0.40
ONE DECIMAL (e.g. 25.0) ±0.20
TWO DECIMALS (e.g. 25.00) ±0.10 CLIENT PROJECT
SURRY HILLS NSW 2010
Phone: 02 9361 6477
Email: [email protected]
26
ANGLES ±0.50°
F45 RETAIL UNIT DESK
THIS DRAWING IS CONFIDENTIAL AND THE PROPERTY OF
DRAWING NAME DRAWING No REV DATE
D3 PRODUCT DESIGN AND IS NOT TO BE REPRODUCED, COPIED
A
NOR OTHERWISE USED IN ANY FORM WHATSO-EVER, NOR IS THE
INFORMATION THEREON AND ASSOCIATED KNOWLEDGE TO BE GENERAL ASSMEBLY D3-?????-??? REV #
01/09/17
DISCUSSED TO THIRD PARTIES WITHOUT PRIOR WRITTEN
PERMISSION FROM D3 PRODUCT DESIGN EXCEPT FOR THE
EXCLUSIVE BENEFIT OF D3 PRODUCT DESIGN.
THE ACCEPTANCE OF THIS DRAWING WILL BE CONSTRUED
DRAWN BY AL 01/09/17 CHECKED BY DF JOB NO ????? SHEET SIZE
AS AN AGREEMENT TO THE FOREGOING CONDITIONS.
© D3 PRODUCT DESIGN 2007 DRAWING SCALE 1:1 SHEET 1 of 1 ALL DIMENSIONS IN mm A2
ADDITIONAL SIGNAGE AND BRANDING

Vehicle Wrap Designs 4x4/SEDAN

There are 5 different options for car wraps for 4X4/sedans and scooters vehicles
to choose from. You can download the print ready files on Playbook.

Car wraps are a great way to create a hype around the opening of your new
studio and reach areas that you wouldn’t normally.

OPTION 1

OPTION 3

OPTION 5

27
ADDITIONAL SIGNAGE AND BRANDING

VESPA

OPTION 1 OPTION 4

OPTION 2 OPTION 5

OPTION 3
28
EXAMPLES OF WHAT IS NOT ALLOWED IN YOUR STUDIO

NON-COMPLIANT Boards, Mirrors and Posters

NON-COMPLIANT Equipment

NON-COMPLIANT Merchandise Display

29
EXAMPLES OF WHAT IS NOT ALLOWED IN YOUR STUDIO

NON-COMPLIANT Desks

NON-COMPLIANT Sled Tracks

NON-COMPLIANT TVs

30
ANNEXURE A - GLOSSARY OF TERMS

In this document, the terms set out below have the meaning given to them.

Agreement means the agreement entered into by you with F45 in relation to the operation of a F45 Studio in a Territory.

“F45”, “F45 Group”, “us” means the F45 group of companies and includes all related body corporates, associated entities and affiliates.
or “we”

Head Office
means the head office operated by F45 in your state or territory.

Premises
means the premises from which the Studio will be operated.

Studio means a F45 Training studio.

You means a F45 Training studio.

31
F45 TRAINING