Chemical Analysis Group 5890 Gas Chromatograph
5890 - Common Cabling \ Pin-outs Document A15707
300
310 320 330 340 Standalone Cable Configuration HP 5890/Data System Cabling Diagrams HP 5880/Data System Cabling Diagrams HP 6890/Data System Cabling Diagrams
Configuration and Cabling
Standalone Cable Configuration for 18594A/B Controllers
310
Figure 310-1
5890 remote connector
+5V
P6
P6
U16
2 1 6 12 8 3 4
?? ??
Start In Ready Sense In Remote Config In
Remote Connector
12 10 8 6 4 2
11 9
2 11 6 Ready Out 9 24V U5 8 K1 5 10 K2 +5V 7 8 10 Start Out
7 5 3 1
12/95
Configuration and Cabling HP Automatic Liquid Sampler Service Manual
310 Standalone Cable Configuration for 18594A/B Controllers
Pin # 1 2 3
Signal Description Remote Start In - TTL Input: expects a pulse input of greater than 5 msec from pin 1 to any ground pin. Ground Remote Config In - TTL Input: expects a contact closure or a jumper from pin 3 to any ground pin. When pin 3 is grounded a run can not be started by pressing START on the GC. It is waiting for a start pulse on pin 1. When using an Automatic Liquid Sampler pressing START on the GC causes the sequence to start. The run is started when the injection is made. Ground Ready Out - Two sides of a single pole, double-throw relay. When 5890 is ready then the contacts connected to 5 & 6 open. Also when 5890 is ready the contacts connected to pins 5 & 9 are closed. Start Out - Two sides of a normally-open relay. Contacts are closed for 50 msec to signal the start of a run. If pin 3 is connected to ground then the contacts are closed when the oven program starts. Same as pin 8. Ground Remote Ready In - TTL input. Expects to be connected to any ground pin by an external device if that device is Not Ready.
4 5&6 or 5&9 7&8
10 11 12
Configuration and Cabling HP Automatic Liquid Sampler Service Manual
12/95
Standalone Cable Configuration for 18594A/B Controllers
310
Figure 310-2. Using the parallel remote PC board. When connecting multiple instruments to the 5890 remote connector there are TWO main causes for running into trouble. They are the following:
5890 A or Series II
Instrument 1
Instrument 2
Parallel Remote Cable (05990-6001 9) Parallel Remote PCB (05990-60320) Example:
Instrument 3
#1 The instruments connecting to the remote connector must use the same polarity on the remote connection (+ and - ). Even when using all HP cables, the connections need to be converted so that the instrument inputs and outputs (+ and ground connections) are the same.
Instrument 1 (+)
Instrument 1 GND 5890 Start Out Instrument 2 GND Instrument 2 (+)
#2 When using multiple instruments, it is important to be aware of which instrument is starting the run. In the case where an Automatic Liquid Sampler is being used as one of the instruments, the sampler will send the start between pin 1 and the ground of the 5890. The other instruments to be started also need to be connected to those same pins on the parallel remote PC board.
13
12/95
Configuration and Cabling HP Automatic Liquid Sampler Service Manual
310 Standalone Cable Configuration for 18594A/B Controllers
Asynchronous standalone cable configuration for HP G1512A controllers
When configured for asynchronous standalone mode, the APG remote connector is redefined to provide independent start, stop, and readiness signals for each injector. Generalpurposecables with spade lugs and a terminal block can be used to connect the output to an HP 35900C/D/E analogtodigital A/D) convertor configured for asynchronous operation. (
Figure 310-3. Typical asynchronous cable configuration. Terminal block 0360-1729 HP G1512A APG remote 35900-60670 (1) (2) 35900-60670 (3) Remote A HP 35900C/D/E (3) 35900-60670 Remote B
PIN # 1 2 3 4 5 6 7 8 9
Function GND Front injector ready in Back injector ready in Front injector ready out Back injector ready out Front Start request Back Start request Front Start out Back Start out
Color code black white red green brown blue orange yellow violet
Color code black (remote A&B) orange (remote A) orange (remote B) N\C N\C violet (remote A) violet (remote B) red (remote A) red (remote B)
NOTE: (1) The remote connector on the HP G1512A is APG-compatible which means it accepts and outputs TTL levels (0 V low, +5 V high) rather than contact closures. (2) This mode is only supported when the GC is in isothermal mode. Typically this means that the GC would not have to be started and, therefore, would require no cabling. 4
Configuration and Cabling HP Automatic Liquid Sampler Service Manual
12/95
HP 5890/Data System Cabling Diagrams
320
Figure 320-1. HP 339x INET integrator.
Out 18594A/B or G1512A In #2
#1
In 5890 Out
#3 Out #1, 2, 3 HPIL Cable 339x In 82167-60002
12/95
Configuration and Cabling HP Automatic Liquid Sampler Service Manual
320 HP 5890/Data System Cabling Diagrams
Figure 320-2. HP non-INET integrator.
#1 18594A/B
Remote 5890
Signal
#2 #1 #2 Y-Cable Analog Signal 03395-60540 35900-60610
3395/6
Figure 320-3. HP 3365 ChemStation (DOS). #1 18594A/B or G1512A 5890
#2 PC ChemStation #1 #2 HP-IB Cable (Straight In) HP-IB Cable 8210-4654 10833B
Configuration and Cabling HP Automatic Liquid Sampler Service Manual
12/95
HP 5890/Data System Cabling Diagrams 320
Figure 320-4. HP ChemStation with 18594A/B controller. #1 18594A/B 5890
#2 PC ChemStation #1 #2 HP-IB Cable (Straight In) HP-IB Cable 8210-4654 10833B
Figure 320-5. HP ChemStation with G1512A controller. #1 G1512A 5890
#3 #2 PC ChemStation #1 #2 #3 HP-IB Cable (Straight In) HP-IB Cable 5890/G1512A Remote Cable 8210-4654 10833B 35900-60700
12/95
Configuration and Cabling HP Automatic Liquid Sampler Service Manual
320 HP 5890/Data System Cabling Diagrams
Figure 320-6. HP MSD ChemStation.
18594A/B or G1512A
#1 5890
#2 #4 #1, 3 PC ChemStation #3 MSD #2 #4 HP-IB Cable (Straight In) HP-IB Cable 5890/MSD Remote 8210-4654 10833B 35900-60700
Figure 320-7. Standalone 18594A/B, 5890. #1 18594A/B 5890 #2 #3 #1 #2 Parallel Remote Cable 5890/Sampler Remote Start 5890 General Purpose Remote 05990-60019 18594-60570 05890-61080
Parallel Remote PCB (05990-60320)
#3
Two wires typically connected to another device: GreenStart BrownGround
Configuration and Cabling HP Automatic Liquid Sampler Service Manual
12/95
HP 5890/Data System Cabling Diagrams 320
Figure 320-8. Non-HP data system.
G1512A
#1 5890
#1 #2 #2 #3 Non-HP Data System #3
Y-Cable 5890/APG 2 Meter General Purpose Remote (spade lugs) 5890 General Purpose Signal (spade lugs)
G1512-60530 35900-60670
05890-61080
Figure 320-9. HP 35900C/D/E analog-to-digital converter. #1 G1512A 5890
#3 #2 35900C/D/E
#1 #2 #3
Y-Cable 5890/APG APG Remote 5890/APG Signal Cable
G1512-60530 G1530-60930 35900-60610
12/95
Configuration and Cabling HP Automatic Liquid Sampler Service Manual
320 HP 5890/Data System Cabling Diagrams
Figure 320-10. G1512A HP 5890A with 18652A A/D box #1 G1512A 5890A
#2 18652A
#1 #2
G1512-60530 01046-60204
14
Configuration and Cabling HP Automatic Liquid Sampler Service Manual
12/95
HP 5880/Data System Cabling Diagrams
Figure 330-1
330
HP 5880A 5880A Mainframe Board 19321-60010
18594A/B 5880A Internal Cable 19321-60500
Cable 5880A/18594A/B 19321-60510
18594A/B Controller Board 18594-60050
15
12/95
Configuration and Cabling HP Automatic Liquid Sampler Service Manual
HP 6890/Data System Cabling Diagrams
340
HP 6890 GC-G1512A
Figure 340-1. G1512A to HP 6890 gas chromatograph
#1 HP 6890A #2 G1512A
#1 #2
RS232 cable G1530-60600 APG remote cable 2M G1530-60930
12/95
Configuration and Cabling HP Automatic Liquid Sampler Service Manual
340 HP 6890/Data System Cabling Diagrams HP 6890 GC-GC ChemStation-GC Automatic Liquid Sampler (ALS)
HP 6890 GC-GC ChemStation-GC Automatic Liquid Sampler (ALS)
Figure 340-2.
1 RS-232 HP 6890 GC 2 APG remote GC ALS
3 HP-IB
GC ChemSta4 RS-232 tion
Modem
Number HP part no. and description 1 2 3 4 G1530-60600, RS-232 cable, 9-pin female/9-pin female G1530-60930, APG remote cable, 2-m, 9-pin male/9-pin male 10833B-2310, 2-m HP-IB cable HP 24542M (also 24540-80012), RS-232 cable
Configuration and Cabling HP Automatic Liquid Sampler Service Manual
12/95
HP 6890/Data System Cabling Diagrams 340 HP 6890 GC-HP Mass Selective Detector-GC ChemStation-GC ALS
HP 6890 GC-HP Mass Selective Detector-GC ChemStation-GC ALS
Figure 340-3.
1 APG remote MSD HP 6890 GC
3 RS-232 GC ALS 4 APG remote
2 HP-IB
2 HP-IB
GC ChemStation
Number HP part no. and description 1 2 3 4 G1530-60930, APG remote cable, 2-m, 9-pin male/9-pin male 10833B-2310, 2-m HP-IB cable G1530-60600, RS-232 cable, 2-m, 9-pin female/9-pin female G1530-60930, APG remote cable, 2-m, 9-pin male/9-pin male
12/95
Configuration and Cabling HP Automatic Liquid Sampler Service Manual
340 HP 6890/Data System Cabling Diagrams HP 6890 GC-GC ALS-Non-HP Data System
HP 6890 GC-GC ALS-Non-HP Data System
Figure 340-4.
1 RS-232 HP 6890 GC GC ALS 2 APG remote
3 APG remote
4 External event Spade lug termination
Number HP part no. and description 1 2 3 4 G1530-60600, 2-m RS-232 cable, 9-pin female/9-pin female G1530-60930, 2-m APG remote cable, 9-pin male/9-pin male 35900-60670, General use APG remote cable, 9-pin male/spade lugs G1530-60590, External event cable, 8-pin/spade lugs
HP 35900-60670 APG remote cable spade lug identification Connector 1 Connector 2 9 pin (male) name
1 2 3 4 5 6 7 8 9 GND Prepare Start Shut down Reserved Power on Ready Stop Start Request
HP G1530-60590 external event cable spade lug identification Pin 1 2 3 4 5 6 7 8 Color Yellow Black Red White Orange Green Brown Blue Signal 24 V Out 1 24 V Out 2 Ground Ground Contact 1 Contact 1 Contact 2 Contact 2
Signal spade lugs
Black White Red Green Brown Blue Orange Yellow Violet
Configuration and Cabling HP Automatic Liquid Sampler Service Manual
12/95
HP 6890/Data System Cabling Diagrams 340 HP 6890 GC-HP 3396B/C or HP 3397A Integrator-GC ALS-Modem
HP 6890 GC-HP 3396B/C or HP 3397A Integrator-GC ALS-Modem
Figure 340-5.
Modem 4 Modem
HP 6890 GC
1 RS-232 2 APG remote
GC ALS
3 INET
INET Integrator
Number 1 2 3 4
HP part no. and description G1530-60600, 2-m RS-232 cable, 9-pin female/9-pin female G1530-60930, 2-m APG remote cable, 9-pin male/9-pin male Two 82167-60003, 5-m INET cables G1530-61120, Modem cable, 9-pin female/9-pin male OR 24540-80012 (also HP 24542M), Modem cable 9-pin female/25-pin male
12/95
Configuration and Cabling HP Automatic Liquid Sampler Service Manual
340 HP 6890/Data System Cabling Diagrams HP 6890 GC-HP 3395A/3396B Integrator-GC ALS
HP 6890 GC-HP 3395A/3396B Integrator-GC ALS
Figure 340-6. 1 RS-232 HP 6890 GC 2 APG remote GC ALS
3 APG remote
4 Analog
HP 3395A/3396B Integrator
Number HP part no. and description 1 2 3 4 G1530-60600, 2-m RS-232 cable, 9-pin female/9-pin female G1530-60930, 2-m APG remote cable, 9-pin male/9-pin male 03396-61020, APG remote cable, 9-pin/15-pin G1530-60570, Analog cable, 2 m, 6-pin
Configuration and Cabling HP Automatic Liquid Sampler Service Manual
12/95
HP 6890/Data System Cabling Diagrams 340 HP 6890 GC-HP 3395B/3396C or HP 3397A Integrator-GC ALS
HP 6890 GC-HP 3395B/3396C or HP 3397A Integrator-GC ALS
Figure 340-7. 1 RS-232 HP 6890 GC 2 APG remote GC ALS
3 APG remote
4 Analog
HP 3395B/3396C Integrator
Number HP part no. and description 1 2 3 4 G1530-60600, 2-m RS-232 cable, 9-pin female/9-pin female G1530-60930, 2-m APG remote cable, 9-pin male/9-pin male 03396-61010, APG remote cable, 9-pin/15-pin G1530-60570, Analog cable, 2 m, 6-pin
12/95
Configuration and Cabling HP Automatic Liquid Sampler Service Manual
340 HP 6890/Data System Cabling Diagrams HP 6890 GC-HP 35900C/D/or E Analog-to-Digital Converter-GC ALS
HP 6890 GC-HP 35900C/D/or E Analog-to-Digital Converter-GC ALS
Figure 340-8. 1 RS-232 HP 6890 GC 2 APG remote GC ALS
3 APG remote
4 Analog
35900 C/D/E A/D converter
Number HP part no. and description 1 2 3 4 G1530-60600, 2-m RS-232 cable, 9-pin female/9-pin female G1530-60930, 2-m APG remote cable, 9-pin male/9-pin male G1530-60930, APG remote, 2-m, 9-pin male/9-pin male G1530-60570, Analog cable, 2-m, 6-pin
16
Configuration and Cabling HP Automatic Liquid Sampler Service Manual
12/95
