Lab - Configure Automated Security Features (Instructor Version)

Instructor Note: Red font color or gray highlights indicate text that appears in the instructor copy only.

Topology

Addressing Table
Device Interface IP Address Subnet Mask Default Gateway Switch Port

R1 G0/0/0 [Link] [Link] N/A N/A

R1
G0/0/1 [Link] [Link] N/A S1 F0/5
R2 G0/0/0 [Link] [Link] N/A N/A

R2
G0/0/1 [Link] [Link] N/A N/A
R3 G0/0/0 [Link] [Link] N/A N/A

© 2015 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public. Page 1 of 17 [Link]
Lab - Securing the Router for Administrative Access

Device Interface IP Address Subnet Mask Default Gateway Switch Port

R3
G0/0/1 [Link] [Link] N/A S3 F0/5
PC-A NIC [Link] [Link] [Link] S1 F0/6
PC-C NIC [Link] [Link] [Link] S3 F0/18
Blank Line, No additional information

Objectives
Part 1: Configure Basic Device Settings
 Cable the network as shown in the topology.
 Configure basic IP addressing for routers and PCs.
 Configure OSPF routing.
 Configure PC hosts.
 Verify connectivity between hosts and routers.
Part 2: Configure Automated Security Features
 Lock down a router using AutoSecure and verify the configuration.
 Contrast using AutoSecure with manually securing a router using the command line.

Background / Scenario
The router is a critical component in any network. It controls the movement of data into and out of the network
and between devices within the network. It is particularly important to protect network routers because the
failure of a routing device could make sections of the network, or the entire network, inaccessible. Controlling
access to routers and enabling reporting on routers is critical to network security and should be part of a
comprehensive security policy.
In this lab, you will build a multi-router network and configure the routers and hosts. You will use automated
security features on router R3.
Note: The routers used with hands-on labs are Cisco 4221 with Cisco IOS XE Release 16.9.6 (universalk9
image). The switches used in the labs are Cisco Catalyst 2960+ with Cisco IOS Release 15.2(7) (lanbasek9
image). Other routers, switches, and Cisco IOS versions can be used. Depending on the model and Cisco
IOS version, the commands available and the output produced might vary from what is shown in the labs.
Refer to the Router Interface Summary Table at the end of the lab for the correct interface identifiers.
Note: Before you begin, ensure that the routers and the switches have been erased and have no startup
configurations.

Required Resources
 3 Routers (Cisco 4221 with Cisco XE Release 16.9.6 universal image or comparable with a Security
Technology Package license)
 2 Switches (Cisco 2960+ with Cisco IOS Release 15.2(7) lanbasek9 image or comparable)
 2 PCs (Windows OS with a terminal emulation program, such as PuTTY or Tera Term installed)
 Console cables to configure Cisco networking devices
 Ethernet cables as shown in the topology

© 2015 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public. Page 2 of 17 [Link]
Lab - Securing the Router for Administrative Access

Instructions

Part 1: Configure Basic Device Settings

In this part, set up the network topology and configure basic settings, such as interface IP addresses.

Step 1: Cable the network.

Attach the devices, as shown in the topology diagram, and cable as necessary.

Step 2: Configure basic settings for each router.

Open configuration window

a. Console into the router and enable privileged EXEC mode.

Router> enable
Router# configure terminal
Configure host names as shown in the topology.
R1(config)# hostname R1
Configure interface IP addresses as shown in the IP Addressing Table.
R1(config)# interface g0/0/0
R1(config-if)# ip address [Link] [Link]
R1(config-if)# no shutdown

R1(config)# interface g0/0/1

R1(config-if)# ip address [Link] [Link]
R1(config-if)# no shutdown
b. To prevent the router from attempting to translate incorrectly entered commands as though they were
host names, disable DNS lookup. R1 is shown here as an example.
R1(config)# no ip domain-lookup

Step 3: Configure OSPF routing on the routers.

a. Use the router ospf command in global configuration mode to enable OSPF on R1.
R1(config)# router ospf 1
b. Configure the network statements for the networks on R1. Use an area ID of 0.
R1(config-router)# network [Link] [Link] area 0
R1(config-router)# network [Link] [Link] area 0
c. Configure OSPF on R2 and R3.
R2(config)# router ospf 1
R2(config-router)# network [Link] [Link] area 0
R2(config-router)# network [Link] [Link] area 0

R3(config)# router ospf 1

R3(config-router)# network [Link] [Link] area 0
R3(config-router)# network [Link] [Link] area 0
d. Issue the passive-interface command to change the G0/0/1 interface on R1 and R3 to passive.
R1(config)# router ospf 1

© 2015 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public. Page 3 of 17 [Link]
Lab - Securing the Router for Administrative Access

R1(config-router)# passive-interface g0/0/1

R3(config)# router ospf 1

R3(config-router)# passive-interface g0/0/1

Step 4: Verify OSPF neighbors and routing information.

a. Issue the show ip ospf neighbor command to verify that each router lists the other routers in the
network as neighbors.
R1# show ip ospf neighbor

Neighbor ID Pri State Dead Time Address Interface

[Link] 1 FULL/BDR [Link] [Link] GigabitEthernet0/0/0

b. Issue the show ip route command to verify that all networks display in the routing table on all routers.
R1# show ip route
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP
a - application route
+ - replicated route, % - next hop override, p - overrides from PfR

Gateway of last resort is not set

[Link]/8 is variably subnetted, 3 subnets, 2 masks

C [Link]/30 is directly connected, GigabitEthernet0/0/0
L [Link]/32 is directly connected, GigabitEthernet0/0/0
O [Link]/30 [110/2] via [Link], [Link], GigabitEthernet0/0/0
[Link]/24 is variably subnetted, 2 subnets, 2 masks
C [Link]/24 is directly connected, GigabitEthernet0/0/1
L [Link]/32 is directly connected, GigabitEthernet0/0/1
O [Link]/24 [110/3] via [Link], [Link], GigabitEthernet0/0/0

Step 5: Configure PC host IP settings.

Configure a static IP address, subnet mask, and default gateway for PC-A and PC-C as shown in the IP
Addressing Table.

Step 6: Verify connectivity between PC-A and PC-C.

a. Ping from R1 to R3.
If the pings are not successful, troubleshoot the basic device configurations before continuing.
b. Ping from PC-A, on the R1 LAN, to PC-C, on the R3 LAN.
If the pings are not successful, troubleshoot the basic device configurations before continuing.
Note: If you can ping from PC-A to PC-C you have demonstrated that OSPF routing is configured and
functioning correctly. If you cannot ping but the device interfaces are up and IP addresses are correct, use the

© 2015 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public. Page 4 of 17 [Link]
Lab - Securing the Router for Administrative Access

show run, show ip ospf neighbor, and show ip route commands to help identify routing protocol-related
problems.
Close configuration window

Part 2: Configure Basic Security Settings on R1

In this part, copy and paste the following commands into R1 to configure basic security settings.
Open configuration window

enable
configure terminal
service password-encryption
security passwords min-length 10
enable algorithm-type scrypt secret cisco12345
ip domain name [Link]
username user01 algorithm-type scrypt secret user01pass
username admin privilege 15 algorithm-type scrypt secret adminpasswd
banner motd " Unauthorized access is strictly prohibited! "
line con 0
exec-timeout 5 0
login local
logging synchronous
line aux 0
exec-timeout 5 0
login local
line vty 0 4
exec-timeout 5 0
privilege level 15
transport input ssh
login local
crypto key generate rsa general-keys modulus 1024
ip ssh time-out 90
ip ssh authentication-retries 2
ip ssh version 2
close configuration window

Part 3: Configure Automated Security Features

In this part, you will do as follows:
 Use AutoSecure to secure R3.
 Review router security configurations with CLI.
By using a single command in CLI mode, the AutoSecure feature allows you to disable common IP services
that can be exploited for network attacks. It can also enable IP services and features that can aid in the
defense of a network when under attack. AutoSecure simplifies the security configuration of a router and
hardens the router configuration.

Step 1: Use the AutoSecure Cisco IOS feature on R3.

a. Enter privileged EXEC mode using the enable command.

© 2015 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public. Page 5 of 17 [Link]
Lab - Securing the Router for Administrative Access

b. Issue the auto secure command on R3 to lock down the router. R2 represents an ISP router, so assume
that R3 G0/0/0 is connected to the internet when prompted by the AutoSecure questions. Respond to the
AutoSecure questions as shown in the following output. The responses are bolded.
Open configuration window

R3# auto secure

--- AutoSecure Configuration ---

*** AutoSecure configuration enhances the security of

the router but it will not make router absolutely secure
from all security attacks ***

All the configuration done as part of AutoSecure will be

shown here. For more details of why and how this configuration
is useful, and any possible side effects, please refer to Cisco
documentation of AutoSecure.
At any prompt you may enter '?' for help.
Use ctrl-c to abort this session at any prompt.

If this device is being managed by a network management station,

AutoSecure configuration may block network management traffic.
Continue with AutoSecure? [no]: yes

Gathering information about the router for AutoSecure

Is this router connected to internet? [no]: yes

Enter the number of interfaces facing internet [1]:
Interface IP-Address OK? Method Status
Protocol
GigabitEthernet0/0/0 [Link] YES manual up up
GigabitEthernet0/0/1 [Link] YES manual up up
Serial0/1/0 unassigned YES unset up up
Serial0/1/1 unassigned YES unset up up
Enter the interface name that is facing internet: GigabitEthernet0/0/0

Securing Management plane services..

Disabling service finger

Disabling service pad
Disabling udp & tcp small servers
Enabling service password encryption
Enabling service tcp-keepalives-in
Enabling service tcp-keepalives-out
Disabling the cdp protocol

Disabling the bootp server

Disabling the http server

© 2015 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public. Page 6 of 17 [Link]
Lab - Securing the Router for Administrative Access

Disabling the finger service

Disabling source routing
Disabling gratuitous arp

Here is a sample Security Banner to be shown

at every access to device. Modify it to suit your
enterprise requirements.

Authorized Access only

This system is the property of So-&-So-Enterprise.
UNAUTHORIZED ACCESS TO THIS DEVICE IS PROHIBITED.
You must have explicit permission to access this
device. All activities performed on this device
are logged. Any violations of access policy will result
in disciplinary action.

Enter the security banner {Put the banner between

k and k, where k is any character}:
# Unauthorized Access Prohibited #
Enable secret is either not configured or
is the same as the enable password
Enter the new enable secret: cisco12345
Confirm the enable secret : cisco12345
Enter the new enable password: 12345cisco
Confirm the enable password: 12345cisco

Configuration of local user database

Enter the username: admin
Enter the password: adminpasswd
Confirm the password: adminpasswd
Configuring AAA local authentication
Configuring console, Aux and vty lines for
local authentication, exec-timeout, transport
Securing device against Login Attacks
Configure the following parameters

Blocking Period when Login Attack detected: 60

Maximum Login failures with the device: 2

Maximum time period for crossing the failed login attempts: 30

Configure SSH server? [yes]: [Enter]

Enter the domain-name: [Link]

© 2015 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public. Page 7 of 17 [Link]
Lab - Securing the Router for Administrative Access

Configuring interface specific AutoSecure services

Disabling the following ip services on all interfaces:

no ip redirects
no ip proxy-arp
no ip unreachables
no ip directed-broadcast
no ip mask-reply

Securing Forwarding plane services..

Enabling unicast rpf on all interfaces connected

to internet

Configure CBAC Firewall feature? [yes/no]: no

This is the configuration generated:

no service finger
no service pad
no service udp-small-servers
no service tcp-small-servers
service password-encryption
service tcp-keepalives-in
service tcp-keepalives-out
no cdp run
no ip bootp server
no ip http server
no ip finger
no ip source-route
no ip gratuitous-arps
banner motd ^C Unauthorized Access Prohibited ^C
security passwords min-length 6
security authentication failure rate 10 log
enable secret 5 $1$lubv$Rdx4gHUcijbxV7p2z76/71
enable password 7 110A1016141D5D5B5C737B
username admin password 7 02050D4808095E731F1A5C
aaa new-model
aaa authentication login local_auth local
line console 0
login authentication local_auth
exec-timeout 5 0
transport output telnet
line aux 0
login authentication local_auth

© 2015 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public. Page 8 of 17 [Link]
Lab - Securing the Router for Administrative Access

exec-timeout 10 0
transport output telnet
line vty 0 4
login authentication local_auth
transport input telnet
line tty 1
login authentication local_auth
exec-timeout 15 0
login block-for 60 attempts 2 within 30
ip domain-name [Link]
crypto key generate rsa general-keys modulus 1024
ip ssh time-out 60
ip ssh authentication-retries 2
line vty 0 4
transport input ssh telnet
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
logging facility local2
logging trap debugging
service sequence-numbers
logging console critical
logging buffered
int GigabitEthernet0/0/0
no ip redirects
no ip proxy-arp
no ip unreachables
no ip directed-broadcast
no ip mask-reply
int GigabitEthernet0/0/1
no ip redirects
no ip proxy-arp
no ip unreachables
no ip directed-broadcast
no ip mask-reply
ip access-list extended 100
permit udp any any eq bootpc
interface GigabitEthernet0/0/0
ip verify unicast source reachable-via rx 100
!
end

Apply this configuration to running-config? [yes]: [Enter]

Applying the config generated to running-config

© 2015 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public. Page 9 of 17 [Link]
Lab - Securing the Router for Administrative Access

WARNING: Command has been added to the configuration using a type 5 password.
However, type 5 passwords will soon be deprecated. Migrate to a supported
password type
WARNING: Command has been added to the configuration using a type 7 password.
However, type 7 passwords will soon be deprecated. Migrate to a supported
password type
WARNING: Command has been added to the configuration using a type 7 password.
However, type 7 passwords will soon be deprecated. Migrate to a supported
password typeThe name for the keys will be: [Link]

% The key modulus size is 1024 bits

% Generating 1024 bit RSA keys, keys will be non-exportable...
[OK] (elapsed time was 0 seconds)

R3#
Note: The questions asked and the output may vary depend on the features on the IOS image and
device.

Step 2: Establish an SSH connection from PC-C to R3.

a. Start PuTTy or another SSH client, and log in with the admin account and password adminpasswd
created when AutoSecure was run. Enter the IP address of the R3 G0/0/1 interface [Link].
b. Because SSH was configured using AutoSecure on R3, you will receive a PuTTY security warning. Click
Yes to connect anyway.
c. Enter privileged EXEC mode with password cisco12345, and verify the R3 configuration using the show
run command.

Step 3: Contrast the AutoSecure-generated configuration of R3 with the manual configuration of

R1.
Questions:

1. What security-related configuration changes were performed on R3 by AutoSecure that were not performed in
previous sections of the lab on R1?
Type your answers here.
Answers will vary but could include: AutoSecure enables AAA and creates a named authentication
list (local_auth). Console, AUX, and vty logins are set up for local authentication. The security
authentication failure rate 10 log command was added. The tcp intercept feature was enabled, ip http
server was disabled, cdp was disabled, security passwords min-length is set to 6. Logging trap
debugging was enabled. Other minor but potentially exploitable services were disabled. An enable
password was created. Logging buffered and logging console critical were enabled.
2. What security-related configuration changes were performed in previous sections of the lab that were not
performed by AutoSecure?
Type your answers here.
Answers will vary but could include: Telnet access was excluded from vty transport input. Additional
accounts were created.

© 2015 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public. Page 10 of 17 [Link]
Lab - Securing the Router for Administrative Access

3. Identify at least five unneeded services that were locked down by AutoSecure and at least three security
measures applied to each interface.
Note: Some of the services listed as being disabled in the AutoSecure output above might not appear in the
show running-config output because they are already disabled by default for this router and Cisco IOS
version.
Services disabled include:
Type your answers here.
no service pad
no cdp run
no ip bootp server
no ip http server
no ip source-route
no ip gratuitous-arps
no ip identd
For each interface, the following were disabled:
Type your answers here.
no ip redirects
no ip proxy-arp
no ip unreachables
4. What are some advantages to using AutoSecure?
Type your answers here.
This tool can catch security vulnerabilities that many network administrators might overlook or be
unaware of. It can lock down a router much faster than entering one command at a time and the tools
result in less potential for entry errors. Also, the tool avoids the need to use complex Cisco IOS
commands and procedures.
Close configuration window

Router Interface Summary Table

Router Model Ethernet Interface #1 Ethernet Interface #2 Serial Interface #1 Serial Interface #2

Gigabit Ethernet 0/0 Gigabit Ethernet 0/1

1900 (G0/0) (G0/1) Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
Gigabit Ethernet 0/0 Gigabit Ethernet 0/1
2900 (G0/0) (G0/1) Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
Gigabit Ethernet 0/0/0 Gigabit Ethernet 0/0/1
4221 (G0/0/0) (G0/0/1) Serial 0/1/0 (S0/1/0) Serial 0/1/1 (S0/1/1)
Gigabit Ethernet 0/0/0 Gigabit Ethernet 0/0/1
4300 (G0/0/0) (G0/0/1) Serial 0/1/0 (S0/1/0) Serial 0/1/1 (S0/1/1)
Blank Line, No additional information

Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many
interfaces the router has. There is no way to effectively list all the combinations of configurations for each router
class. This table includes identifiers for the possible combinations of Ethernet and Serial interfaces in the device.
The table does not include any other type of interface, even though a specific router may contain one. An example
of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation that can be used in
Cisco IOS commands to represent the interface.

© 2015 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public. Page 11 of 17 [Link]
Lab - Securing the Router for Administrative Access

Device Configs

Router R1
R1# show run
Building configuration...

Current configuration : 1932 bytes

!
version 16.9
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
platform qfp utilization monitor load 80
platform punt-keepalive disable-kernel-core
!
hostname R1
!
boot-start-marker
boot-end-marker
!
security passwords min-length 10
enable secret 9 $9$608LjMVuvbEJZK$bG8hofgigO/nhdeamLoGOaHSBNqCt7DvjDQECDEbWrs
!
no aaa new-model
!
no ip domain lookup
ip domain name [Link]
!
login on-success log
!
subscriber templating
!
multilink bundle-name authenticated
!
spanning-tree extend system-id
!
username user01 secret 9
$9$[Link].6a$fZzGLtwBmw7/MyYlkNO1J3tPKPZEnEdFeem7vgrfdQw
username admin privilege 15 secret 9
$9$tsj8PFFTy1v294$1WywiLRIrkYnnjWn/6B4HnGRPDkFOMC/iGn5m6operU
!
redundancy
mode none
!
interface GigabitEthernet0/0/0
ip address [Link] [Link]
negotiation auto
!

© 2015 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public. Page 12 of 17 [Link]
Lab - Securing the Router for Administrative Access

interface GigabitEthernet0/0/1
ip address [Link] [Link]
negotiation auto
!
router ospf 1
passive-interface GigabitEthernet0/0/1
network [Link] [Link] area 0
network [Link] [Link] area 0
!
ip forward-protocol nd
no ip http server
ip http secure-server
!
ip ssh time-out 90
ip ssh authentication-retries 2
ip ssh version 2
!
control-plane
!
banner motd ^C Unauthorized access is strictly prohibited! ^C
!
line con 0
exec-timeout 5 0
logging synchronous
login local
transport input none
stopbits 1
line aux 0
exec-timeout 5 0
login local
stopbits 1
line vty 0 4
exec-timeout 5 0
privilege level 15
login local
transport input ssh
end

Router R2
R2# show run
Building configuration...

Current configuration : 1138 bytes

!
version 16.9
service timestamps debug datetime msec
service timestamps log datetime msec
platform qfp utilization monitor load 80

© 2015 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public. Page 13 of 17 [Link]
Lab - Securing the Router for Administrative Access

platform punt-keepalive disable-kernel-core

!
hostname R2
!
boot-start-marker
boot-end-marker
!
no aaa new-model
!
no ip domain lookup
!
login on-success log
!
subscriber templating
!
multilink bundle-name authenticated
!
redundancy
mode none
!
interface GigabitEthernet0/0/0
ip address [Link] [Link]
negotiation auto
!
interface GigabitEthernet0/0/1
ip address [Link] [Link]
negotiation auto
!
router ospf 1
network [Link] [Link] area 0
network [Link] [Link] area 0
!
ip forward-protocol nd
no ip http server
ip http secure-server
!
control-plane
!
line con 0
logging synchronous
transport input none
stopbits 1
line aux 0
stopbits 1
line vty 0 4
login
!
end

© 2015 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public. Page 14 of 17 [Link]
Lab - Securing the Router for Administrative Access

Router R3
R3# show run
Building configuration...

Current configuration : 2604 bytes

!
version 16.9
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
platform qfp utilization monitor load 80
platform punt-keepalive disable-kernel-core
!
hostname R3
!
boot-start-marker
boot-end-marker
!
security authentication failure rate 10 log
security passwords min-length 6
logging console critical
enable secret 5 $1$KRNj$os8y9zWDfLjSVDb2Ol.eS1
enable password 7 091D1C5A4D50141B180F0B
!
aaa new-model
!
aaa authentication login local_auth local
!
aaa session-id common
no ip source-route
no ip gratuitous-arps
!
no ip bootp server
no ip domain lookup
ip domain name [Link]
!
!
login block-for 60 attempts 2 within 30
login on-success log
!
subscriber templating
!
multilink bundle-name authenticated
!

© 2015 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public. Page 15 of 17 [Link]
Lab - Securing the Router for Administrative Access

spanning-tree extend system-id

!
username admin password 7 011202095205160E325F590D
!
redundancy
mode none
!
no cdp run
!
interface GigabitEthernet0/0/0
ip address [Link] [Link]
no ip redirects
no ip unreachables
no ip proxy-arp
ip verify unicast source reachable-via rx 100
negotiation auto
!
interface GigabitEthernet0/0/1
ip address [Link] [Link]
no ip redirects
no ip unreachables
no ip proxy-arp
negotiation auto
!
interface Serial0/1/0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
!
interface Serial0/1/1
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
!
router ospf 1
passive-interface GigabitEthernet0/0/1
network [Link] [Link] area 0
network [Link] [Link] area 0
!
ip forward-protocol nd
no ip http server
ip http secure-server
!
ip ssh time-out 60
ip ssh authentication-retries 2
!
logging trap debugging

© 2015 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public. Page 16 of 17 [Link]
Lab - Securing the Router for Administrative Access

logging facility local2

ip access-list extended 100
permit udp any any eq bootpc
!
control-plane
!
banner motd ^C Unauthorized Access Prohibited ^C
!
line con 0
exec-timeout 5 0
logging synchronous
login authentication local_auth
transport input none
transport output telnet
stopbits 1
line aux 0
exec-timeout 15 0
login authentication local_auth
transport output telnet
stopbits 1
line vty 0 4
login authentication local_auth
transport input telnet ssh
!
end
End of document

© 2015 - 2024 Cisco and/or its affiliates. All rights reserved. Cisco Public. Page 17 of 17 [Link]