MVI56E-MNETR

Modbus TCP/IP Interface Module

with Reduced Data Block

February 7, 2023

USER MANUAL
Your Feedback Please
We always want you to feel that you made the right decision to use our products. If you have suggestions,
comments, compliments or complaints about our products, documentation, or support, please write or call us.

How to Contact Us
ProSoft Technology, Inc.
+1 (661) 716-5100
+1 (661) 716-5101 (Fax)
www.prosoft-technology.com
[email protected]

MVI56E-MNETR User Manual

For Public Use.

February 7, 2023

ProSoft Technology ®, ProLinx ®, inRAx ®, ProTalk ®, and RadioLinx ® are Registered Trademarks of ProSoft
Technology, Inc. All other brand or product names are or may be trademarks of, and are used to identify
products and services of, their respective owners.

Content Disclaimer
This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability
of these products for specific user applications. It is the duty of any such user or integrator to perform the
appropriate and complete risk analysis, evaluation and testing of the products with respect to the relevant
specific application or use thereof. Neither ProSoft Technology nor any of its affiliates or subsidiaries shall be
responsible or liable for misuse of the information contained herein. Information in this document including
illustrations, specifications and dimensions may contain technical inaccuracies or typographical errors. ProSoft
Technology makes no warranty or representation as to its accuracy and assumes no liability for and reserves the
right to correct such inaccuracies or errors at any time without notice. If you have any suggestions for
improvements or amendments or have found errors in this publication, please notify us.
No part of this document may be reproduced in any form or by any means, electronic or mechanical, including
photocopying, without express written permission of ProSoft Technology. All pertinent state, regional, and local
safety regulations must be observed when installing and using this product. For reasons of safety and to help
ensure compliance with documented system data, only the manufacturer should perform repairs to components.
When devices are used for applications with technical safety requirements, the relevant instructions must be
followed. Failure to use ProSoft Technology software or approved software with our hardware products may
result in injury, harm, or improper operating results. Failure to observe this information can result in injury or
equipment damage.
Copyright © 2023 ProSoft Technology, Inc. All Rights Reserved.

For professional users in the European Union

If you wish to discard electrical and electronic equipment (EEE), please contact your dealer or
supplier for further information.

Warning – Cancer and Reproductive Harm – www.P65Warnings.ca.gov

Open Source Information

Open Source Software used in the product

The product contains, among other things, Open Source Software files, as defined below, developed by third
parties and licensed under an Open Source Software license. These Open Source Software files are protected
by copyright. Your right to use the Open Source Software is governed by the relevant applicable Open Source
Software license conditions. Your compliance with those license conditions will entitle you to use the Open
Source Software as foreseen in the relevant license. In the event of conflicts between other ProSoft Technology,
Inc. license conditions applicable to the product and the Open Source Software license conditions, the Open
Source Software conditions shall prevail. The Open Source Software is provided royalty-free (i.e. no fees are
charged for exercising the licensed rights). Open Source Software contained in this product and the respective
Open Source Software licenses are stated in the module webpage, in the link Open Source.

If Open Source Software contained in this product is licensed under GNU General Public License (GPL), GNU
Lesser General Public License (LGPL), Mozilla Public License (MPL) or any other Open Source Software
license, which requires that source code is to be made available and such source code is not already delivered
together with the product, you can order the corresponding source code of the Open Source Software from
ProSoft Technology, Inc. - against payment of the shipping and handling charges - for a period of at least 3 years
since purchase of the product. Please send your specific request, within 3 years of the purchase date of this
product, together with the name and serial number of the product found on the product label to:

ProSoft Technology, Inc.

Director of Engineering
9201 Camino Media, Suite 200
Bakersfield, CA 93311
USA

Warranty regarding further use of the Open Source Software

ProSoft Technology, Inc. provides no warranty for the Open Source Software contained in this product, if such
Open Source Software is used in any manner other than intended by ProSoft Technology, Inc. The licenses
listed below define the warranty, if any, from the authors or licensors of the Open Source Software. ProSoft
Technology, Inc. specifically disclaims any warranty for defects caused by altering any Open Source Software or
the product’s configuration. Any warranty claims against ProSoft Technology, Inc. in the event that the Open
Source Software contained in this product infringes the intellectual property rights of a third party are excluded.
The following disclaimer applies to the GPL and LGPL components in relation to the rights holders:
“This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the
implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General
Public License and the GNU Lesser General Public License for more details.”

For the remaining open source components, the liability exclusions of the rights holders in the respective license
texts apply. Technical support, if any, will only be provided for unmodified software.
Important Safety Information

North America Warnings

A Warning - Explosion Hazard - Substitution of components may impair suitability for Class I, Division 2.
B Warning - Explosion Hazard - When in hazardous locations, turn off power before replacing or rewiring
modules.
C Warning - Explosion Hazard - Do not disconnect equipment unless power has been switched off or the area
is known to be nonhazardous.
D Class 2 Power

ATEX Warnings and Conditions of Safe Usage

Power, Input, and Output (I/O) wiring must be in accordance with the authority having jurisdiction
A Warning - Explosion Hazard - When in hazardous locations, turn off power before replacing or wiring
modules.
B Warning - Explosion Hazard - Do not disconnect equipment unless power has been switched off or the area
is known to be non-hazardous.
C These products are intended to be mounted in an IP54 enclosure. The devices shall provide external means
to prevent the rated voltage being exceeded by transient disturbances of more than 40%. This device must
be used only with ATEX certified backplanes.
D DO NOT OPEN WHEN ENERGIZED.

Electrical Ratings
▪ Backplane Current Load: 800 mA @ 5 Vdc; 3 mA @ 24 Vdc
▪ Operating Temperature: 0°C to 60°C (32°F to 140°F)
▪ Storage Temperature: -40°C to 85°C (-40°F to 185°F)
▪ Shock: 30 g operational; 50 g non-operational; Vibration: 5 g from 10 Hz to 150 Hz
▪ Relative Humidity 5% to 95% (without condensation)
▪ All phase conductor sizes must be at least 1.3 mm2 and all earth ground conductors must be at least 4mm2.

Agency Approvals & Certifications

Please visit our website: www.prosoft-technology.com
MVI56E-MNETR ♦ ControlLogix™ Platform Contents
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Contents
Your Feedback Please ................................................................................................................ 2
How to Contact Us ....................................................................................................................... 2
Content Disclaimer ...................................................................................................................... 2
Important Safety Information ....................................................................................................... 4

1 Start Here 8
1.1 What's New? ...................................................................................................... 8
1.2 System Requirements ....................................................................................... 9
1.3 Package Contents ...........................................................................................10
1.4 Setting Jumpers ...............................................................................................10
1.5 Installing the Module in the Rack .....................................................................11
1.6 Importing the Sample Add-On Instruction .......................................................11
1.7 Creating a New RSLogix 5000 Project ............................................................12
1.7.1 Creating the Remote Network .........................................................................13
1.7.2 Creating the Module - Remote Rack ...............................................................15
1.7.3 Creating the Module - Local Rack ...................................................................17
1.7.4 Importing the Add-On Instruction .....................................................................19
1.8 Downloading the Sample Program to the Processor.......................................30

2 Configuring the MVI56E-MNETR Module 31

2.1 Installing ProSoft Configuration Builder ...........................................................31
2.2 Using ProSoft Configuration Builder Software .................................................31
2.2.1 Upgrading from MVI56-MNETR in ProSoft Configuration Builder ...................31
2.2.2 Setting Up the Project ......................................................................................32
2.2.3 Setting Module Parameters .............................................................................33
2.2.4 Module .............................................................................................................34
2.2.5 MNET Client x ..................................................................................................38
2.2.6 MNET Client x Commands ..............................................................................40
2.2.7 MNET Servers .................................................................................................47
2.2.8 Static ARP Table .............................................................................................49
2.2.9 Ethernet Configuration .....................................................................................50
2.3 Connecting Your PC to the Module .................................................................51
2.3.1 Setting Up a Temporary IP Address ................................................................51
2.4 Downloading the Project to the Module ...........................................................55
2.4.1 Using CIPconnect to Connect to the Module ...................................................57
2.4.2 Using RSWho to Connect to the Module .........................................................65

3 Ladder Logic 66
3.1 Controller Tags ................................................................................................66
3.1.1 MVI56E-MNETR Controller Tags ....................................................................66
3.2 User-Defined Data Types (UDTs)....................................................................68
3.2.1 MVI56(E)-MNETR User-Defined Data Types ..................................................68
3.3 Using Controller Tags ......................................................................................69
3.4 Controller Tag Overview ..................................................................................70
3.4.1 MNETR.DATA..................................................................................................70
3.4.2 MNETR.STATUS .............................................................................................73
3.4.3 MNETR.CONTROL .........................................................................................73

ProSoft Technology, Inc. Page 5 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Contents
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

3.4.4 MNETR.UTIL ...................................................................................................74

4 Diagnostics and Troubleshooting 75

4.1 LED Status Indicators ......................................................................................75
4.1.1 Scrolling LED Status Indicators .......................................................................75
4.1.2 Ethernet LED Indicators ...................................................................................76
4.1.3 Non-Scrolling LED Status Indicators ...............................................................77
4.1.4 Clearing a Fault Condition ...............................................................................77
4.1.5 Troubleshooting ...............................................................................................78
4.2 Using the Diagnostics Menu in ProSoft Configuration Builder ........................79
4.2.1 Connecting to the Module's Webpage .............................................................82
4.2.2 The Diagnostics Menu .....................................................................................83
4.2.3 Monitoring Module Information ........................................................................84
4.2.4 Monitoring Backplane Information ...................................................................85
4.2.5 Monitoring MNET Client Information................................................................85
4.2.6 Monitoring MNET Server Information ..............................................................86
4.2.7 Monitoring Database Information.....................................................................86
4.3 Reading Status Data from the Module ............................................................87
4.3.1 Status Data Definition ......................................................................................88
4.3.2 Client Configuration Error Word .......................................................................89
4.3.3 Client Command Errors ...................................................................................90

5 Reference 92
5.1 Product Specifications .....................................................................................92
5.1.1 General Specifications .....................................................................................92
5.1.2 Functional Specifications .................................................................................93
5.1.3 Hardware Specifications ..................................................................................93
5.2 Module Power Up ............................................................................................94
5.3 Backplane Data Transfer .................................................................................95
5.3.1 Normal Data Transfer Blocks ...........................................................................97
5.3.2 Special Function Blocks .................................................................................100
5.4 Data Flow between MVI56E-MNETR and ControlLogix Processor ..............110
5.4.1 Server Driver ..................................................................................................111
5.4.2 Client Driver ...................................................................................................113
5.5 Ethernet Cable Specifications........................................................................115
5.5.1 Ethernet Cable Configuration ........................................................................115
5.5.2 Ethernet Performance ....................................................................................115
5.6 Modbus Protocol Specification ......................................................................116
5.6.1 About the Modbus TCP/IP Protocol ...............................................................116
5.6.2 Commands Supported by the Module ...........................................................117
5.6.3 Read Coil Status (Function Code 01) ............................................................118
5.6.4 Read Input Status (Function Code 02) ..........................................................119
5.6.5 Read Holding Registers (Function Code 03) .................................................120
5.6.6 Read Input Registers (Function Code 04) .....................................................121
5.6.7 Force Single Coil (Function Code 05) ...........................................................122
5.6.8 Preset Single Register (Function Code 06) ...................................................123
5.6.9 Diagnostics (Function Code 08) ....................................................................124
5.6.10 Force Multiple Coils (Function Code 15) .......................................................126
5.6.11 Preset Multiple Registers (Function Code 16) ...............................................127
5.6.12 Modbus Exception Responses ......................................................................128
5.7 Using the Optional Add-On Instruction Rung Import .....................................130
5.7.1 Before You Begin ...........................................................................................130

ProSoft Technology, Inc. Page 6 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Contents
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.7.2 Overview ........................................................................................................130

5.7.3 Installing the Rung Import with Optional Add-On Instruction .........................131
5.7.4 Reading the Ethernet Settings from the Module............................................135
5.7.5 Writing the Ethernet Settings to the Module ..................................................136
5.7.6 Reading the Clock Value from the Module ....................................................137
5.7.7 Writing the Clock Value to the Module ..........................................................138
5.8 Adding the Module to an Existing Project ......................................................139
5.9 Using the Sample Program............................................................................142
5.9.1 Opening the Sample Program in RSLogix .....................................................142
5.9.2 Choosing the Controller Type ........................................................................144
5.9.3 Selecting the Slot Number for the Module .....................................................145
5.9.4 Downloading the Sample Program to the Processor.....................................146
5.9.5 Adding the Sample Ladder to an Existing Application ...................................146

6 Support, Service & Warranty 147

6.1 Contacting Technical Support........................................................................147
6.2 Warranty Information .....................................................................................147

ProSoft Technology, Inc. Page 7 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Start Here
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

1 Start Here
To get the most benefit from this User Manual, you should have the following skills:
• Rockwell Automation® RSLogix™ software: launch the program, configure ladder
logic, and transfer the ladder logic to the processor
• Microsoft Windows: install and launch programs, execute menu commands,
navigate dialog boxes, and enter data
• Hardware installation and wiring: install the module, and safely connect Modbus
TCP/IP and ControlLogix devices to a power source and to the MVI56E-MNETR
module’s application port(s)

1.1 What's New?

MVI56E products are backward compatible with existing MVI56 products, ladder logic,
and module configuration files already in use. Easily swap and upgrade products while
benefiting from an array of new features designed to improve interoperability and
enhance ease-of-use.
• ProSoft Configuration Builder (PCB): New Windows software for diagnostics,
connecting via the module's Ethernet port or CIPconnect®, to upload/download
module configuration information and access troubleshooting features and functions.
• ProSoft Discovery Service (PDS): Utility software to find and display a list of
MVI56E modules on the network and to temporarily change an IP address to connect
with a module's web page.
• CIPconnect-enabled: Allows PC-to-module configuration and diagnostics from the
Ethernet network through a ControlLogix 1756-ENBT EtherNet/IP™ module.
• Personality Module: An industrial compact flash memory card storing the module’s
complete configuration and Ethernet settings, allowing quick and easy replacement.
• LED Scrolling Diagnostic Display: 4-character, alphanumeric display, providing
standard English messages for status and alarm data, and for processor and
network communication status.

ProSoft Technology, Inc. Page 8 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Start Here
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

1.2 System Requirements

The MVI56E-MNETR module requires the following minimum hardware and software
components:
• Rockwell Automation ControlLogix® processor (firmware version 10 or higher), with
compatible power supply, and one free slot in the rack for the MVI56E-MNETR
module. The module requires 800 mA of available 5 Vdc power
• Rockwell Automation RSLogix 5000 programming software
o Version 16 or higher required for Add-On Instruction
o Version 15 or lower must use Sample Ladder, available from
www.prosoft-technology.com
• Rockwell Automation RSLinx® communication software version 2.51 or higher
• ProSoft Configuration Builder (PCB) (included)
• ProSoft Discovery Service (PDS) (included in PCB)
• Pentium® II 450 MHz minimum. Pentium III 733 MHz (or better) recommended
• Supported operating systems:
o Microsoft Windows 10
o Microsoft Windows 7 Professional (32-or 64-bit)
o Microsoft Windows 2000 Professional with Service Pack 1, 2, or 3
o Microsoft Windows Server 2003
• 128 Mbytes of RAM minimum, 256 Mbytes of RAM recommended
• 100 Mbytes of free hard disk space (or more based on application requirements)

Note: The Hardware and Operating System requirements in this list are the minimum recommended to
install and run software provided by ProSoft Technology®. Other third party applications may have different
minimum requirements. Refer to the documentation for any third party applications for system requirements.

Note: You can install the module in a local or remote rack. For remote rack installation, the module requires
EtherNet/IP or ControlNet communication with the processor.

ProSoft Technology, Inc. Page 9 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Start Here
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

1.3 Package Contents

The following components are included with your MVI56E-MNETR module, and are all
required for installation and configuration.

Important: Before beginning the installation, please verify that all of the following items are present.

Qty. Part Name Part Number Part Description

1 MVI56E-MNETR MVI56E-MNETR Modbus TCP/IP Interface Module with
Module Reduced Data Block

1.4 Setting Jumpers

The Setup Jumper acts as "write protection" for the module’s firmware. In "write
protected" mode, the Setup pins are not connected, and the module’s firmware cannot
be overwritten. The module is shipped with the Setup jumper OFF. Do not jumper the
Setup pins together unless you are directed to do so by ProSoft Technical Support (or
you want to update the module firmware).
The following illustration shows the jumper configuration in the OFF position

Note: If you are installing the module in a remote rack, you may prefer to leave the Setup pins jumpered.
You can update the module’s firmware without requiring physical access to the module.

Security considerations:

Leaving the Setup pin jumpered leaves the module open to unexpected firmware updates.

You should consider segmenting the data flow for security reasons. Per IEC 62443-1-1, you should align
with IEC 62443 and implement segmentation of the control system. Relevant capabilities are firewalls,
unidirectional communication, DMZ. Oil and Gas customers should also see DNVGL-RP-G108 for guidance
on partitioning.

You should practice security by design, per IEC 62443-4-1, including layers of security and detection. The
module relies on overall network security design, as it is only one component of what should be a defined
zone or subnet.

ProSoft Technology, Inc. Page 10 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Start Here
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

1.5 Installing the Module in the Rack

If you have not already installed and configured your ControlLogix processor and power
supply, please do so before installing the MVI56E-MNETR module. Refer to your
Rockwell Automation product documentation for installation instructions.

Warning: You must follow all safety instructions when installing this or any other electronic devices. Failure
to follow safety procedures could result in damage to hardware or data, or even serious injury or death to
personnel. Refer to the documentation for each device you plan to connect to verify that suitable safety
procedures are in place before installing or servicing the device.

After you have checked the placement of the jumpers, insert the MVI56E-MNETR into
the ControlLogix chassis. Use the same technique recommended by Rockwell
Automation to remove and install ControlLogix modules.
You can install or remove ControlLogix system components while chassis power is
applied and the system is operating. However, please note the following warning.

Warning: When you insert or remove the module while backplane power is on, an electrical arc can occur.
An electrical arc can cause personal injury or property damage by sending an erroneous signal to your
system’s actuators. This can cause unintended machine motion or loss of process control. Electrical arcs
may also cause an explosion when they happen in a hazardous environment. Verify that power is removed
or the area is non-hazardous before proceeding.

Repeated electrical arcing causes excessive wear to contacts on both the module and its mating connector.
Worn contacts may create electrical resistance that can affect module operation.

1.6 Importing the Sample Add-On Instruction

Note: This section only applies if your processor is using RSLogix 5000 version 16 or higher. If you have an
earlier version, please see Using the Sample Program (page 142).

Before You Begin

Two Add-On Instructions are provided for the MVI56E-MNETR module. The first is
required for setting up the module; the second is optional.
Copy the files from www.prosoft-technology.com. Save them to a convenient location in
your PC, such as Desktop or My Documents.

File Name Description

MVI56EMNETR_AddOn_Rung_vXXX.L5X L5X file containing Add-On Instruction, user defined
data types, controller tags and ladder logic required
to configure the MVI56E-MNETR module
MVI56EMNETR_Optional_Rung_vXXX.L5X Optional L5X file containing additional Add-On
Instruction with logic for changing Ethernet
configuration and clock settings.

ProSoft Technology, Inc. Page 11 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Start Here
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

1.7 Creating a New RSLogix 5000 Project

1 Open the FILE menu, and then choose NEW.

2 Select your ControlLogix controller model.

3 Select REVISION 16.
4 Enter a name for your controller, such as My_Controller.
5 Select your ControlLogix chassis type.
6 Select SLOT 0 for the controller.

ProSoft Technology, Inc. Page 12 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Start Here
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

1.7.1 Creating the Remote Network

Note: If you are installing the MVI56E-MNETR module in a remote rack, follow these steps. If you are
installing the module in a local rack, follow the steps in Creating the Module - Local Rack (page 17).

1 Right-click I/O CONFIGURATION and choose NEW MODULE.

2 Expand the Communications module selections and then select the Ethernet Bridge
module that matches your hardware. This example uses a 1756-ENBT/A module.

Note: If you are prompted to Select Major Revision, choose the lower of the available revision numbers.

ProSoft Technology, Inc. Page 13 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Start Here
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

3 Name the ENBT/A module, then set the IP Address and slot location in the local rack
with the ControlLogix processor.

4 Click OK.
5 Next, select the 1756-ENBT module that you just created in the Controller
Organization pane and click the right mouse button to open a shortcut menu. On the
shortcut menu, choose NEW MODULE.

6 Repeat steps 2 and 3 to add the second EtherNet/IP module to the remote rack.

ProSoft Technology, Inc. Page 14 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Start Here
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

1.7.2 Creating the Module - Remote Rack

Note: To continue installing the MVI56E-MNETR module in a remote rack, follow the next steps. If you are
installing the module in a local rack, follow the steps in Creating the Module - Local Rack (page 17).

1 Next, select the remote 1756 BACKPLANE node in the Controller Organization pane
underneath the remote rack EtherNet/IP module you just created and click the right
mouse button to open a shortcut menu. On the shortcut menu, choose NEW MODULE.

This action opens the SELECT MODULE dialog box.

2 Select the 1756-MODULE (GENERIC 1756 MODULE) from the list and click OK. This
action opens the New Module dialog box.

ProSoft Technology, Inc. Page 15 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Start Here
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

3 Set the Module Properties values as follows:

Parameter Value
Name Enter a module identification string. The recommended value is
MNETR.
Description Enter a description for the module. Example: MODBUS TCP/IP
INTERFACE MODULE WITH REDUCED DATA BLOCK.
Comm Format Select DATA-INT (Very Important)
Slot Enter the slot number in the rack where the MVI56E-MNETR
module will be installed.
Input Assembly Instance 1
Input Size 42
Output Assembly Instance 2
Output Size 42
Configuration Assembly Instance 4
Configuration Size 0

4 On the CONNECTION tab, set the RPI value for your project. Fifty (50) milliseconds is
usually a good starting value.

The MVI56E-MNETR module is now visible in the I/O CONFIGURATION section.

ProSoft Technology, Inc. Page 16 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Start Here
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

1.7.3 Creating the Module - Local Rack

Note: If you are installing the MVI56E-MNETR module in a local rack, follow these steps. If you are
installing the module in a remote rack, follow the steps in Creating the Module - Remote Rack (page 13).

1 Add the MVI56E-MNETR module to the project.

In the Controller Organization window, select I/O CONFIGURATION and click the right
mouse button to open a shortcut menu. On the shortcut menu, choose NEW MODULE.

This action opens the Select Module dialog box.

2 Select the 1756-MODULE (GENERIC 1756 MODULE) from the list and click OK. This
action opens the New Module dialog box.

ProSoft Technology, Inc. Page 17 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Start Here
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

3 Set the Module Properties values as follows:

Parameter Value
Name Enter a module identification string. The recommended value is
MNETR.
Description Enter a description for the module. Example: MODBUS TCP/IP
INTERFACE MODULE WITH REDUCED DATA BLOCK.
Comm Format Select DATA-INT (Very Important)
Slot Enter the slot number in the rack where the MVI56E-MNETR
module is to be installed.
Input Assembly Instance 1
Input Size 42
Output Assembly Instance 2
Output Size 42
Configuration Assembly Instance 4
Configuration Size 0

4 On the CONNECTION tab, set the RPI value for your project. Five (5) milliseconds is
usually a good starting value. Click OK to confirm.

The MVI56E-MNETR module is now visible in the I/O CONFIGURATION section.

ProSoft Technology, Inc. Page 18 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Start Here
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

1.7.4 Importing the Add-On Instruction

1 In the Controller Organization window, expand the Tasks folder and subfolder until
you reach the MainProgram folder.
2 In the MainProgram folder, double-click to open the MAINROUTINE ladder.
3 Select an empty rung in the new routine, and then click the right mouse button to
open a shortcut menu. On the shortcut menu, choose IMPORT RUNG.

4 Navigate to the location on your PC where you saved (page 11) the Add-On
Instruction (for example, My Documents or Desktop). Select the
MVI56EMNETR_ADDON_RUNG_V1_3.L5X file.

ProSoft Technology, Inc. Page 19 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Start Here
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

This action opens the Import Configuration dialog box, showing the controller tags
that will be created.
o If you are installing the module in a Remote Rack, open the dropdown menus for
the Input and Output tags, and select the MNETR module in the remote rack.

5 Click OK to confirm the import. RSLogix will indicate that the import is in progress:

ProSoft Technology, Inc. Page 20 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Start Here
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

When the import is complete, you will see the new Add-On Instruction rung in the
ladder.

The procedure has also imported new user-defined data types, data objects and the
Add-On instruction for your project.

6 Save the application and then download the sample ladder logic into the processor.

ProSoft Technology, Inc. Page 21 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Start Here
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Adding Multiple Modules (Optional)

Important: If your application requires more than one MVI56-MNETR module into the same project, follow
the steps below.

1 In the I/O Configuration folder, click the right mouse button to open a shortcut menu,
and then choose NEW MODULE.

2 Select 1756-MODULE.

This action opens the New Module dialog box.

ProSoft Technology, Inc. Page 22 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Start Here
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

3 Fill in the module properties as follows:

Parameter Value
Name Enter a module identification string. Example: MNETR_2
Description Enter a description for the module. Example: MODBUS TCP/IP
INTERFACE MODULE WITH REDUCED DATA BLOCK
Comm Format Select DATA-INT
Slot Enter the slot number in the rack where the MVI56E-MNETR module
is located.
Input Assembly Instance 1
Input Size 42
Output Assembly Instance 2
Output Size 42
Configuration Assembly 4
Instance
Configuration Size 0

4 Click OK to confirm. The new module is now visible:

5 Expand the Tasks folder, and then expand the MainTask folder.
6 On the MainProgram folder, click the right mouse button to open a shortcut menu.
On the shortcut menu, choose NEW ROUTINE.
7 In the New Routine dialog box, enter the name and description of your routine, and
then click OK.

ProSoft Technology, Inc. Page 23 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Start Here
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

8 Select an empty rung in the new routine, and then click the right mouse button to
open a shortcut menu. On the shortcut menu, choose IMPORT RUNG.

9 Select the file MVI56(E)MNETR_AddOn_Rung_<Version#>.L5X

ProSoft Technology, Inc. Page 24 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Start Here
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

This action opens the IMPORT CONFIGURATION dialog box, showing the controller tags
that will be created.

10 Associate the I/O connection variables to the correct module. The default values are
Local:1:I and Local:1:O so these require change.

ProSoft Technology, Inc. Page 25 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Start Here
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Or, in a Remote Rack application…

11 Change the default tags MNETR and AOI56MNETR to avoid conflict with existing
tags. In this step, you should append a string to the default tag names, such as "_2",
as shown in the following illustration.

ProSoft Technology, Inc. Page 26 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Start Here
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

12 Click OK to confirm.

Or, in a Remote Rack application…

ProSoft Technology, Inc. Page 27 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Start Here
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Adjusting the Input and Output Array Sizes

The module internal database is divided into two user-configurable areas:

• Read Data
• Write Data
The Read Data area is moved from the module to the processor, while the Write Data
area is moved from the processor to the module.
The MVI56E-MNETR Add-On Instruction rung is configured for 600 registers of Read
Data and 600 registers of Write Data, which is sufficient for most applications. However,
you can configure the sizes of these data areas to meet the needs of your application.
1 In ProSoft Configuration Builder, expand the Module icon in the tree view and
double-click MODULE to open an Edit window. Change the READ REGISTER COUNT to
contain the number of words for your Read Data area.

Important: Because the module pages data in blocks of 40 registers at a time, you should configure your
user data areas in multiples of 40 registers.

2 To modify the WriteData array, follow the above steps, substituting WriteData for
ReadData.
3 Save and download the configuration to the module (page 55) and reboot.
Make sure that the ReadData and WriteData arrays do not overlap in the module
memory. For example, if your application requires 2000 words of WriteData starting at
register 0, then your Read Register Start parameter must be set to a value of 2000 or
greater.

ProSoft Technology, Inc. Page 28 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Start Here
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Adjusting the Input and Output Array Sizes in Logix 5000

You will also need to adjust the sizes of the MNETR.DATA.ReadData and
MNETR.DATA.WriteData Controller Tag arrays to accommodate the Read Register
Count and Write Register Count values configured in PCB.

1 In the Controller Organizer pane of RSLogix 5000, double-click on the MNETRDATA

UDT.

2 Edit the ReadData array size to match or exceed the value of the Read Register
Count parameter in PCB.

3 Repeat Step 2 for the WriteData array size. Then click OK.
4 Once complete, the MNETR.DATA.ReadData and MNETR.DATA.WriteData
Controller Tag array sizes are updated.

ProSoft Technology, Inc. Page 29 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Start Here
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

1.8 Downloading the Sample Program to the Processor

Note: The key switch on the front of the ControlLogix processor must be in the REM or PROG position.

1 If you are not already online with the processor, open the Communications menu,
and then choose DOWNLOAD. RSLogix 5000 will establish communication with the
processor. You do not have to download through the processor's serial port, as
shown here. You may download through any available network connection.
2 When communication is established, RSLogix 5000 will open a confirmation dialog
box. Click the DOWNLOAD button to transfer the sample program to the processor.

3 RSLogix 5000 will compile the program and transfer it to the processor. This process
may take a few minutes.
4 When the download is complete, RSLogix 5000 will open another confirmation dialog
box. If the key switch is in the REM position, click OK to switch the processor from
PROGRAM mode to RUN mode.

Note: If you receive an error message during these steps, refer to your RSLogix documentation to interpret
and correct the error.

ProSoft Technology, Inc. Page 30 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

2 Configuring the MVI56E-MNETR Module

2.1 Installing ProSoft Configuration Builder
1 Download the ProSoft Configuration Builder from www.prosoft-technology.com.
2 Run the installation file to start the installation wizard.

2.2 Using ProSoft Configuration Builder Software

ProSoft Configuration Builder (PCB) provides a convenient way to manage module
configuration files customized to meet your application needs. PCB is not only a
powerful solution for new configuration files, but also allows you to import information
from previously installed (known working) configurations to new projects.

Note: During startup and initialization, the MVI56E-MNETR module receives its protocol and backplane
configuration information from the installed Personality Module (Compact Flash). Use ProSoft Configuration
Builder to configure module settings and to download changes to the Personality Module.

2.2.1 Upgrading from MVI56-MNETR in ProSoft Configuration Builder

MVI56E-MNETR modules are fully backward-compatible with MVI56-MNETR modules.
However, you will need to convert your MVI56-MNETR configuration in ProSoft
Configuration Builder to a form that your new MVI56E-MNETR module will accept when
you download it.
ProSoft Configuration Builder version 2.2.2 or later has an upgrade option that easily
performs this conversion, while preserving all your configuration settings and any name
you may have given your module.

Important: For this procedure, you need to have ProSoft Configuration Builder version 2.2.2 or later
installed on your PC. You can download the latest version from www.prosoft-technology.com.

ProSoft Technology, Inc. Page 31 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

1 In ProSoft Configuration Builder's tree view, click the MODULE icon and right-click to
open a shortcut menu.

2 On the shortcut menu, select CHANGE MODULE TYPE TO MVI56E-MNETR.

2.2.2 Setting Up the Project

If you have used other Windows configuration tools before, you will find the screen
layout familiar. PCB’s window consists of a tree view on the left, and an information pane
and a configuration pane on the right side of the window. When you first start PCB, the
tree view consists of folders for Default Project and Default Location, with a Default
Module in the Default Location folder. The following illustration shows the PCB window
with a new project.

1 In PCB select DEFAULT MODULE in the tree view, and then click the right mouse
button to open a shortcut menu.

ProSoft Technology, Inc. Page 32 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

2 On the shortcut menu, select CHOOSE MODULE TYPE. This action opens the Choose
Module Type dialog box.

3 In the Product Line Filter area of the dialog box, select MVI56E. In the Select Module
Type dropdown list, select MVI56E-MNETR, and then click OK to save your settings
and return to the ProSoft Configuration Builder window.

2.2.3 Setting Module Parameters

Notice that the contents of the information pane and the configuration pane changed
when you added the MVI56E-MNETR module to the project.

ProSoft Technology, Inc. Page 33 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

At this time, you may wish to rename the Default Project and Default Location folders in
the tree view.

Renaming an Object
1 Select the object, and then click the right mouse button to open a shortcut menu.
From the shortcut menu, choose RENAME.
2 Type the name to assign to the object.
3 Click away from the object to save the new name.

Configuring Module Parameters

1 Click the [+] sign next to the module icon to expand module information.
2 Click the [+] sign next to any icon to view module information and configuration
options.
3 Double-click any icon to open an Edit dialog box.
4 To edit a parameter, select the parameter in the left pane and make your changes in
the right pane.
5 Click OK to save your changes.

Printing a Configuration File

1 Select the module icon, and then click the right mouse button to open a shortcut
menu.
2 On the shortcut menu, choose VIEW CONFIGURATION. This action opens the View
Configuration window.
3 In the View Configuration window, open the FILE menu, and choose PRINT. This
action opens the Print dialog box.
4 In the Print dialog box, choose the printer to use from the drop-down list, select
printing options, and then click OK.

2.2.4 Module
This section of the configuration describes the database setup and module-level
parameters.

Backplane Error/Status Pointer

1 to 4955
This parameter sets the address in the internal database where the backplane
error/status data will be placed. If you want the error/status data to be moved to the
processor and placed into the ReadData array, the value entered should be a module
memory address in the Read Data area. If the value is set to -1, the error/status data will
not be stored in the module's internal database and will not be transferred to the
processor's ReadData array.
Enabling the Error/Status Pointer is optional. The error/status data is routinely returned
as part of the input image, which is continually being transferred from the module to the
processor. For more information, see Normal Data Transfer Blocks (page 97).

ProSoft Technology, Inc. Page 34 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Read Register Start

0 to 4999
The Read Register Start parameter specifies the start of the Read Data area in module
memory. Data in this area will be transferred from the module to the processor.

Note: Total user database memory space is limited to the first 5000 registers of module
memory, addresses 0 through 4999. Therefore, the practical limit for this parameter is
4999 minus the value entered for Read Register Count, so that the Read Data Area
does not try to extend above address 4999. Read Data and Write Data Areas must be
configured to occupy separate address ranges in module memory and should not be
allowed to overlap.

ProSoft Technology, Inc. Page 35 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Read Register Count

0 to 5000
The Read Register Count parameter specifies the size of the Read Data area of module
memory and the number of registers to transfer from this area to the processor, up to a
maximum of 5000 words.

Note: Total Read Register Count and Write Register Count cannot exceed 5000 total
registers. Read Data and Write Data Areas must be configured to occupy separate
address ranges in module memory and should not be allowed to overlap.

Write Register Start

0 to 4999
The Write Register Start parameter specifies the start of the Write Data area in module
memory. Data in this area will be transferred in from the processor.

Note: Total user database memory space is limited to the first 5000 registers of module
memory, addresses 0 through 4999. Therefore, the practical limit for this parameter is
4999 minus the value entered for Write Register Count, so that the Write Data Area does
not try to extend above address 4999. Read Data and Write Data Areas must be
configured to occupy separate address ranges in module memory and should not be
allowed to overlap.

Write Register Count

0 to 5000
The Write Register Count parameter specifies the size of the Write Data area of module
memory and the number of registers to transfer from the processor to this memory area,
up to a maximum value of 5000 words.

Note: Total Read Register Count and Write Register Count cannot exceed 5000 total
registers. Read Data and Write Data Areas must be configured to occupy separate
address ranges in module memory and should not be allowed to overlap.

ProSoft Technology, Inc. Page 36 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Failure Flag Count

0 through 65535
This parameter specifies the number of successive transfer errors that must occur
before halting communication on the application port(s). If the parameter is set to 0, the
application port(s) will continue to operate under all conditions. If the value is set larger
than 0 (1 to 65535), communications will cease if the specified number of failures occur.

Initialize Output Data

0 = No, 1 = Yes
This parameter is used to determine if the output data for the module should be
initialized with values from the processor. If the value is set to 0, the output data will be
initialized to 0. If the value is set to 1, the data will be initialized with data from the
processor. Use of this option requires associated ladder logic to pass the data from the
processor to the module.

Pass-Through Mode
0, 1, 2 or 3
This parameter specifies the pass-through mode for write messages received by the
MNET and MBAP server ports.
• If the parameter is set to 0, all write messages will be placed in the module’s virtual
database.
• If a value of 1 is entered, write messages received will be sent to the processor as
unformatted messages.
• If a value of 2 is entered, write messages received will be sent to the processor with
the bytes swapped in a formatted message.
• If a value of 3 is entered, write messages received will be sent to the processor as
formatted messages.

Note: If pass-through mode is used, the module's Write Data area must begin at 0 (Write
Register Start = 0).

Duplex/Speed Code
0, 1, 2, 3 or 4
This parameter allows you to cause the module to use a specific duplex and speed
setting.
• Value = 1: Half duplex, 10 MB speed
• Value = 2: Full duplex, 10 MB speed
• Value = 3: Half duplex, 100 MB speed
• Value = 4: Full duplex, 100 MB speed
• Value = 0: Auto-negotiate
Auto-negotiate is the default value for backward compatibility. This feature is not
implemented in older software revisions.

ProSoft Technology, Inc. Page 37 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

2.2.5 MNET Client x

This section defines general configuration for the MNET Client (Master).

Client Error/Status Pointer

1 to 4990
This parameter sets the address in the internal database where the Client error/status
data will be placed. If you want the error/status data to be moved to the processor and
placed into the ReadData array, the value entered should be a module memory address
in the Read Data area. If the value is set to -1, the error/status data will not be stored in
the module's internal database and will not be transferred to the processor's ReadData
array.
Enabling the Error/Status Pointer is optional. The error/status data is routinely returned
as part of the input image, which is continually being transferred from the module to the
processor. For more information, see Normal Data Transfer Blocks (page 97).

Command Error Pointer

-1 to 4999
This parameter sets the address in the internal database where the Command Error List
data will be placed. If you want the Command Error List data to be moved to the
processor and placed into the ReadData array, the value entered should be a module
memory address in the Read Data area. If the value is set to -1, the Command Error List
data will not be stored in the module's internal database and will not be transferred to the
processor's ReadData array.

Minimum Command Delay

0 to 65535 milliseconds
This parameter specifies the number of milliseconds to wait between the initial issuances
of a command. This parameter can be used to delay all commands sent to servers to
avoid "flooding" commands on the network. This parameter does not affect retries of a
command as they will be issued when failure is recognized.

Response Timeout
0 to 65535 milliseconds
This is the time in milliseconds that a Client will wait before re-transmitting a command if
no response is received from the addressed server. The value to use depends on the
type of communication network used, and the expected response time of the slowest
device on the network.

Retry Count
0 to 10
This parameter specifies the number of times a command will be retried if it fails.

ProSoft Technology, Inc. Page 38 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Float Flag
YES or NO
This flag specifies how the Client driver will issue Function Code 3, 6, and 16 commands
(read and write Holding Registers) to a remote server when it is moving 32-bit floating-
point data.
If the remote server expects to receive or will send one complete 32-bit floating-point
value for each count of one (1), then set this parameter to YES. When set to YES, the
Client driver will send values from two consecutive 16-bit internal memory registers (32
total bits) for each count in a write command, or receive 32 bits per count from the server
for read commands. Example: Count = 10, Client driver will send 20 16-bit registers for
10 total 32-bit floating-point values.
If, however, the remote server expects to use a count of two (2) for each 32-bit floating-
point value it sends or receives, or if you do not plan to use floating-point data in your
application, then set this parameter to NO, which is the default setting.
You will also need to set the Float Start and Float Offset parameters to appropriate
values whenever the Float Flag parameter is set to YES.

Float Start
0 to 65535
Whenever the Float Flag parameter is set to YES, this parameter determines the lowest
Modbus Address, used in commands to a remote server, to consider as commands to
read or write floating-point data. All commands with address values greater than or equal
to this value will be considered floating-point data commands. All commands with
address values less than this value will be considered normal 16-bit register data
commands.
This parameter is used only if the Float Flag is set to YES. For example, if a value of
7000 is entered, all commands sent with addresses of 47001 (or 407001) and above will
be considered as floating-point data commands and 32 bits of data will be sent or
received for each count of one in the command.
You will also need to set the Float Offset parameter to an appropriate value whenever
the Float Flag parameter is set to YES.

Float Offset
0 to 9999
This parameter defines the start register for floating-point data in the internal database.
This parameter is used only if the Float Flag is enabled. For example, if the Float Offset
value is set to 3000 and the Float Start parameter is set to 7000, data requests for
register 7000 will use the internal Modbus register 3000.

ARP Timeout
1 to 60
This parameter specifies the number of seconds to wait for an ARP reply after a request
is issued.

ProSoft Technology, Inc. Page 39 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Command Error Delay

0 to 300
This parameter specifies the number of 100 millisecond intervals to turn off a command
in the error list after an error is recognized for the command. If this parameter is set to 0,
there will be no delay.

2.2.6 MNET Client x Commands

The MNET Client x Commands section of the configuration sets the Modbus TCP/IP
Client command list. This command list polls Modbus TCP/IP server devices attached to
the Modbus TCP/IP Client port. The module supports numerous commands. This
permits the module to interface with a wide variety of Modbus TCP/IP protocol devices.
The function codes used for each command are those specified in the Modbus protocol.
Each command list record has the same format. The first part of the record contains the
information relating to the MVI56E-MNETR communication module, and the second part
contains information required to interface to the Modbus TCP/IP server device.

Command List Overview

In order to interface the MVI56E-MNETR module with Modbus TCP/IP server devices,
you must construct a command list. The commands in the list specify the server device
to be addressed, the function to be performed (read or write), the data area in the device
to interface with and the registers in the internal database to be associated with the
device data. The Client command list supports up to 100 commands.
The command list is processed from top (command #1) to bottom. A poll interval
parameter is associated with each command to specify a minimum delay time in tenths
of a second between the issuances of a command. If the user specifies a value of 10 for
the parameter, the command will be executed no more frequently than every 1 second.
Write commands have a special feature, as they can be set to execute only if the data in
the write command changes. If the register data values in the command have not
changed since the command was last issued, the command will not be executed.
If the data in the command has changed since the command was last issued, the
command will be executed. Use of this feature can lighten the load on the network. To
implement this feature, set the enable code for the command to CONDITIONAL (2).

ProSoft Technology, Inc. Page 40 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Commands Supported by the Module

The format of each command in the list depends on the Modbus Function Code being
executed. The following table lists the functions supported by the module.

Function Code Definition Supported in Client Supported in Server

1 Read Coil Status X X
2 Read Input Status X X
3 Read Holding Registers X X
4 Read Input Registers X X
5 Set Single Coil X X
6 Single Register Write X X
7 Read Exception Status X
8 Diagnostics X
15 Multiple Coil Write X X
16 Multiple Register Write X X
22 Mask Write 4X X
23 Read/Write X

Each command list record has the same general format. The first part of the record
contains the information relating to the communication module and the second part
contains information required to interface to the Modbus TCP/IP server device.

Command Entry Formats

The following table shows the structure of the configuration data necessary for each of
the supported commands.

1 2 3 4 5 6 7 8 9 10
Enable Internal Poll Interval Count Swap IP Address Serv Slave Function Code Device
Code Address Time Code Port Node Modbus
Address
Register 1/10th Seconds Bit Count 0 IP Address Port # Address Read Coil (0x) Register
(bit)
Code Register 1/10th Seconds Bit Count 0 IP Address Port # Address Read Input (1x) Register
(bit)
Code Register 1/10th Seconds Word Code IP Address Port # Address Read Holding Register
Count Registers (4x)
Code Register 1/10th Seconds Word 0 IP Address Port # Address Read Input Registers Register
Count (3x)
Code 1 bit 1/10th Seconds Bit Count 0 IP Address Port # Address Force (Write) Single Register
Coil (0x)
Code 1 bit 1/10th Seconds Word 0 IP Address Port # Address Preset (Write) Single Register
Count Register (4x)
Code Register 1/10th Seconds Bit Count 0 IP Address Port # Address Force (Write) Multiple Register
(bit) Coil (0x)
Code Register 1/10th Seconds Word 0 IP Address Port # Address Preset (Write) Multiple Register
Count Register (4x)

The first part of the record is the module information, which relates to the MVI56E
module, and the second part contains information required to interface to the server
device.

ProSoft Technology, Inc. Page 41 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Command list example:

Enable
NO (0), YES (1), or CONDITIONAL (2)
This field defines whether the command is to be executed and under what conditions.

Value Description
NO (0) The command is disabled and will not be executed in the normal polling
sequence.
YES (1) The command is executed each scan of the command list if the Poll Interval
time is set to zero. If the Poll Interval time is set to a nonzero value, the
command will be executed when the interval timer expires.
CONDITIONAL (2) The command will execute only if the internal data associated with the
command changes. This value is valid only for write commands.

Internal Address
0 to 65535 (for bit-level addressing)
or
0 to 4999 (for word-level addressing)
This field specifies the database address in the module's internal database to use as the
destination for data brought in by a read command or as the source for data to be sent
out by a write command. The database address is interpreted as a bit address or a 16-
bit word (register) address, depending on the Modbus Function Code used in the
command.
• For Modbus functions 1, 2, 5, and 15, this parameter is interpreted as a bit-level
address.
• For Modbus functions 3, 4, 6, and 16, this parameter is interpreted as a word-level or
register-level address.

ProSoft Technology, Inc. Page 42 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Poll Interval
0 to 65535
This parameter specifies the minimum interval between issuances of a command during
continuous command execution (Enable code of 1). The parameter is entered in tenths
of a second. Therefore, if a value of 100 is entered for a command, the command
executes no more frequently than every 10 seconds.

Reg Count
Regs: 1 to 125
Coils: 1 to 800
This parameter specifies the number of 16-bit registers or binary bits to be transferred by
the command.
• Functions 5 and 6 ignore this field as they apply only to a single data point.
• For functions 1, 2, and 15, this parameter sets the number of bits (inputs or coils) to
be transferred by the command.
• For functions 3, 4, and 16, this parameter sets the number of registers to be
transferred by the command.

ProSoft Technology, Inc. Page 43 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Swap Code
NONE
SWAP WORDS
SWAP WORDS & BYTES
SWAP BYTES
This parameter defines if and how the order of bytes in data received or sent is to be
rearranged. This option exists to allow for the fact that different manufacturers store and
transmit multi-byte data in different combinations. This parameter is helpful when dealing
with floating-point or other multi-byte values, as there is no one standard method of
storing these data types. The parameter can be set to rearrange the byte order of data
received or sent into an order more useful or convenient for other applications. The
following table defines the valid Swap Code values and the effect they have on the byte-
order of the data.

Swap Code Description

NONE No change is made in the byte ordering (1234 = 1234)
SWAP WORDS The words are swapped (1234=3412)
SWAP WORDS & BYTES The words are swapped, then the bytes in each word are swapped
(1234=4321)
SWAP BYTES The bytes in each word are swapped (1234=2143)

These swap operations affect 4-byte (or 2-word) groups of data. Therefore, data
swapping using these Swap Codes should be done only when using an even number of
words, such as when 32-bit integer or floating-point data is involved.

Node IP Address
xxx.xxx.xxx.xxx
The IP address of the device being addressed by the command.

Service Port
502 or other port numbers supported on a server
Use a value of 502 when addressing Modbus TCP/IP servers that are compatible with
the Schneider Electric MBAP specifications (this will be most devices). If a server
implementation supports another service port, enter the value here.

ProSoft Technology, Inc. Page 44 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Slave Address
0 - Broadcast to all nodes
1 to 255
Use this parameter to specify the slave address of a remote Modbus Serial device
through a Modbus Ethernet to Serial converter.

Note: Use the Node IP Address parameter (page 44) to address commands to a remote Modbus TCP/IP
device.

Note: Most Modbus devices accept an address in the range of only 1 to 247, so check with the slave device
manufacturer to see if a particular slave can use addresses 248 to 255.

If the value is set to zero, the command will be a broadcast message on the network. The Modbus protocol
permits broadcast commands for write operations. Do not use node address 0 for read operations.

Modbus Function
1, 2, 3, 4, 5, 6, 15, or 16
This parameter specifies the Modbus Function Code to be executed by the command.
These function codes are defined in the Modbus protocol. The following table lists the
purpose of each function supported by the module. More information on the protocol is
available from www.modbus.org.

Modbus Function Code Description

1 Read Coil Status
2 Read Input Status
3 Read Holding Registers
4 Read Input Registers
5 Force (Write) Single Coil
6 Preset (Write) Single Register
15 Force Multiple Coils
16 Preset Multiple Registers

ProSoft Technology, Inc. Page 45 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

MB Address in Device
This parameter specifies the starting Modbus register or bit address in the server to be
used by the command. Refer to the documentation of each Modbus server device for the
register and bit address assignments valid for that device.
The Modbus Function Code determines whether the address will be a register-level or
bit-level OFFSET address into a given data type range. The offset will be the target data
address in the server minus the base address for that data type. Base addresses for the
different data types are:
• 00001 or 000001 (0x0001) for bit-level Coil data (Function Codes 1, 5, and 15).
• 10001 or 100001 (1x0001) for bit-level Input Status data (Function Code 2)
• 30001 or 300001 (3x0001) for Input Register data (Function Code 4)
• 40001 or 400001 (4x0001) for Holding Register data (Function Codes 3, 6, and 16).
Address calculation examples:
• For bit-level Coil commands (FC 1, 5, or 15) to read or write a Coil 0X address
00001, specify a value of 0 (00001 - 00001 = 0).
• For Coil address 00115, specify 114
(00115 - 00001 = 114)
• For register read or write commands (FC 3, 6, or 16) 4X range, for 40001, specify a
value of 0
(40001 - 40001 = 0).
• For 01101, 11101, 31101 or 41101, specify a value of 1100.
(01101 - 00001 = 1100)
(11101 -10001 = 1100)
(31101 - 30001 = 1100)
(41101 - 40001 = 1100)

Note: If the documentation for a particular Modbus server device lists data addresses in hexadecimal
(base16) notation, you will need to convert the hexadecimal value to a decimal value to enter in this
parameter. In such cases, it is not usually necessary to subtract 1 from the converted decimal number, as
this addressing scheme typically uses the exact offset address expressed as a hexadecimal number.

Comment
0 to 35 alphanumeric characters

ProSoft Technology, Inc. Page 46 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

2.2.7 MNET Servers

This section contains database offset information used by the server when accessed by
external Clients. These offsets can be utilized to segment the database by data type.

Float Flag
YES or NO
This flag specifies how the server driver will respond to Function Code 3, 6, and 16
commands (read and write Holding Registers) from a remote Client when it is moving
32-bit floating-point data.
If the remote Client expects to receive or will send one complete 32-bit floating-point
value for each count of one (1), then set this parameter to YES. When set to YES, the
server driver will return values from two consecutive 16-bit internal memory registers (32
total bits) for each count in the read command, or receive 32-bits per count from the
Client for write commands. Example: Count = 10, server driver will send 20 16-bit
registers for 10 total 32-bit floating-point values.
If, however, the remote Client sends a count of two (2) for each 32-bit floating-point
value it expects to receive or send, or, if you do not plan to use floating-point data in your
application, then set this parameter to NO, which is the default setting.
You will also need to set the Float Start and Float Offset parameters to appropriate
values whenever the Float Flag parameter is set to YES.

ProSoft Technology, Inc. Page 47 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Float Start
0 to 65535
This parameter defines the first register of floating-point data. All requests with register
values greater than or equal to this value will be considered floating-point data requests.
This parameter is only used if the Float Flag is enabled. For example, if a value of 7000
is entered, all requests for registers 7000 and above will be considered as floating-point
data.

Float Offset
0 to 9999
This parameter defines the start register for floating-point data in the internal database.
This parameter is used only if the Float Flag is enabled. For example, if the Float Offset
value is set to 3000 and the Float Start parameter is set to 7000, data requests for
register 7000 will use the internal Modbus register 3000.

Output Offset
0 to 4999
This parameter defines the start register for the Modbus command data in the internal
database. This parameter is enabled when a value greater than 0 is set. For example, if
the Output Offset value is set to 3000, data requests for Modbus Coil Register address
00001 will use the internal database register 3000, bit 0. If the Output Offset value is set
to 3000, data requests for Modbus Coil register address 00016 will use the internal
database register 3000, bit 15. Function codes affected are 1, 5, and 15.

Bit Input Offset

0 to 4999
This parameter defines the start register for Modbus command data in the internal
database. This parameter is enabled when a value greater than 0 is set. For example, if
the Bit Input Offset value is set to 3000, data requests for Modbus Input Register
address 10001 will use the internal database register 3000, bit 0. If the Bit Input Offset is
set to 3000, data requests for Modbus Coil register address 10016 will use the internal
database register 3000, bit 15. Function code 2 is affected.

Holding Register Offset

0 to 4999
This parameter defines the start register for the Modbus Command data in the internal
database. This parameter is enabled when a value greater than 0 is set. For example, if
the Holding Register Offset value is set to 4000, data requests for Modbus Word register
40001 will use the internal database register 4000. Function codes affected are 3, 6, 16,
& 23.

ProSoft Technology, Inc. Page 48 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Word Input Offset

0 to 4999
This parameter defines the start register for Modbus Command data in the internal
database. This parameter is enabled when a value greater than 0 is set. For example, if
the Word Input Offset value is set to 4000, data requests for Modbus Word register
address 30001 will use the internal database register 4000. Function code 4 is affected.

Connection Timeout
0 to 1200 seconds
Number of seconds the server will wait to receive new data. If the server does not
receive any new data during this time, it will close the connection.

2.2.8 Static ARP Table

The Static ARP Table defines a list of static IP addresses that the module will use when
an ARP (Address Resolution Protocol) is required. The module will accept up to 40 static
IP/MAC address data sets.
Use the Static ARP table to reduce the amount of network traffic by specifying IP
addresses and their associated MAC (hardware) addresses that the MVI56E-MNETR
module will be communicating with regularly.

Important: If the device in the field is changed, this table must be updated to contain the new MAC address
for the device and downloaded to the module. If the MAC is not changed, no communications with the
module will be provided.

IP Address
Dotted notation
This table contains a list of static IP addresses that the module will use when an ARP is
required. The module accepts up to 40 static IP/MAC address sets.

Important: If the device in the field is changed, this table must be updated to contain the new MAC address
for the device and downloaded to the module. If the MAC is not changed, no communications with the
module will occur.

Hardware MAC Address

Hex value
This table contains a list of static MAC addresses that the module will use when an ARP
is required. The module accepts up to 40 static IP/MAC address sets.

Important: If the device in the field is changed, this table must be updated to contain the new MAC address
for the device and downloaded to the module. If the MAC is not changed, no communications with the
module will occur.

ProSoft Technology, Inc. Page 49 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

2.2.9 Ethernet Configuration

Use this procedure to configure the Ethernet settings for your module. You must assign
an IP address, subnet mask and gateway address. After you complete this step, you can
connect to the module with an Ethernet cable.
1 Determine the network settings for your module, with the help of your network
administrator if necessary. You will need the following information:
o IP address (fixed IP required) _____ . _____ . _____ . _____
o Subnet mask _____ . _____ . _____ . _____
o Gateway address _____ . _____ . _____ . _____

Note: The gateway address is optional, and is not required for networks that do not use a default gateway.

2 Double-click the ETHERNET CONFIGURATION icon. This action opens the Edit dialog
box.

3 Edit the values for my_ip, netmask (subnet mask) and gateway (default gateway).
4 When you are finished editing, click OK to save your changes and return to the
ProSoft Configuration Builder window.

ProSoft Technology, Inc. Page 50 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

2.3 Connecting Your PC to the Module

With the module securely mounted, connect one end of the Ethernet cable to the Config
(E1) Port, and the other end to an Ethernet hub or switch accessible from the same
network as your PC. You can also connect directly from the Ethernet Port on your PC to
the Config (E1) Port on the module by using an Ethernet crossover cable (not included).

2.3.1 Setting Up a Temporary IP Address

Important: ProSoft Configuration Builder locates MVI56E-MNETR modules through UDP broadcast
messages. These messages may be blocked by routers or layer 3 switches. In that case, ProSoft Discovery
Service will be unable to locate the modules.

To use ProSoft Configuration Builder, arrange the Ethernet connection so that there is no router/ layer 3
switch between the computer and the module OR reconfigure the router/ layer 3 switch to allow routing of
the UDP broadcast messages.

1 In the tree view in ProSoft Configuration Builder, select the MVI56E-MNETR module.

ProSoft Technology, Inc. Page 51 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

2 Click the right mouse button to open a shortcut menu. On the shortcut menu, choose
DIAGNOSTICS.

3 In the Diagnostics window, click the SET UP CONNECTION button.

ProSoft Technology, Inc. Page 52 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

4 In the Connection Setup dialog box, click the BROWSE DEVICE(S) button to open the
ProSoft Discovery Service. Select the module, then right-click and choose ASSIGN
TEMPORARY IP.

5 The module’s default IP address is 192.168.0.250. Choose an unused IP within your

subnet, and then click OK.

Important: The temporary IP address is only valid until the next time the module is initialized. For
information on how to set the module’s permanent IP address, see Ethernet Configuration (page 50).

ProSoft Technology, Inc. Page 53 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

6 Close the ProSoft Discovery Service window. Enter the temporary IP in the Ethernet
address field of the Connection Setup dialog box, then click the TEST CONNECTION
button to verify that the module is accessible with the current settings.

7 If the Test Connection is successful, click CONNECT. The Diagnostics menu will
display in the Diagnostics window.

ProSoft Technology, Inc. Page 54 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

2.4 Downloading the Project to the Module

Note: For alternative methods of connecting to the module with your PC, refer to Using CIPconnect to
Connect to the Module (page 57) or Using RSWho to Connect to the Module (page 65).

In order for the module to use the settings you configured, you must download (copy) the
updated Project file from your PC to the module.
1 In the tree view in ProSoft Configuration Builder, click once to select the MVI56E-
MNETR module.
2 Open the PROJECT menu, and then choose MODULE / DOWNLOAD.
This action opens the Download dialog box. Notice that the Ethernet address field
contains the temporary IP address you assigned previously. ProSoft Configuration
Builder will use this temporary IP address to connect to the module.

Click TEST CONNECTION to verify that the IP address allows access to the module.
3 If the connection succeeds, click DOWNLOAD to transfer the Ethernet configuration to
the module.

ProSoft Technology, Inc. Page 55 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

If the Test Connection procedure fails, you will see an error message. To correct the
error, follow these steps.
1 Click OK to dismiss the error message.
2 In the Download dialog box, click BROWSE DEVICE(S) to open ProSoft Discovery
Service.

3 Select the module, and then click the right mouse button to open a shortcut menu.
On the shortcut menu, choose SELECT FOR PCB.
4 Close ProSoft Discovery Service.
5 Click DOWNLOAD to transfer the configuration to the module.

ProSoft Technology, Inc. Page 56 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

2.4.1 Using CIPconnect to Connect to the Module

You can use CIPconnect® to connect a PC to the MVI56E-MNETR module over Ethernet
using Rockwell Automation’s 1756-ENBT EtherNet/IP® module. This allows you to
configure the MVI56E-MNETR module and network, upload and download files, and
view network and module diagnostics from a PC. RSLinx is not required when you use
CIPconnect. All you need are:
• The IP addresses and slot numbers of any 1756-ENBT modules in the path
• The ControlNet node numbers and slot numbers of any 1756-CNBx ControlNet
Bridge modules in the path
• The slot number of the MVI56E-MNETR in the destination ControlLogix chassis (the
last ENBT/CNBx and chassis in the path).

To use CIPconnect, follow these steps.

1 In the Select Connection Type dropdown list, choose 1756-ENBT. The default path
appears in the text box, as shown in the following illustration.

2 Click CIP PATH EDIT to open the CIPconnect Path Editor dialog box.

ProSoft Technology, Inc. Page 57 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

The CIPconnect Path Editor allows you to define the path between the PC and the
MVI56E-MNETR module. The first connection from the PC is always a 1756-ENBT
(Ethernet/IP) module.

Each row corresponds to a physical rack in the CIP path.

• If the MVI56E-MNETR module is located in the same rack as the first 1756-ENBT
module, select RACK NO. 1 and configure the associated parameters.
• If the MVI56E-MNETR is available in a remote rack (accessible through ControlNet
or Ethernet/IP), include all racks (by using the ADD RACK button).

Parameter Description
Source Module Source module type. This field is automatically selected
depending on the destination module of the last rack
(1756-CNB or 1756-ENBT).
Source Module IP Address IP address of the source module (only applicable for
1756-ENBT)
Source Module Node Address Node address of the source module (only applicable for
1756-CNB)
Destination Module Select the destination module associated to the source module
in the rack. The connection between the source and destination
modules is performed through the backplane.
Destination Module Slot Number The slot number where the destination MVI56E module is
located.

To use the CIPconnect Path Editor, follow these steps.

1 Configure the path between the 1756-ENBT connected to your PC and the MVI56E-
MNETR module.
o If the module is located in a remote rack, add more racks to configure the full
path.
o The path can only contain ControlNet or Ethernet/IP networks.
o The maximum number of supported racks is six.
2 Click CONSTRUCT CIP PATH to build the path in text format
3 Click OK to confirm the configured path.

ProSoft Technology, Inc. Page 58 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Example 1: Local Rack Application

For this example, the MVI56E-MNETR module is located in the same rack as the 1756-
ENBT that is connected to the PC.

MVI56E Module 1756-ENBT

Rack 1

0 1 2 3
Ethernet

Rack 1
Slot Module Network Address
0 ControlLogix Processor -
1 Any -
2 MVI56E-MNETR -
3 1756-ENBT IP=192.168.0.100

1 In the Download dialog box, click CIP PATH EDIT.

ProSoft Technology, Inc. Page 59 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

2 Configure the path as shown in the following illustration, and click CONSTRUCT CIP
PATH to build the path in text format.

Click OK to close the CIPconnect Path Editor and return to the Download dialog box.
3 Check the new path in the Download dialog box.

ProSoft Technology, Inc. Page 60 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

4 Click TEST CONNECTION to verify that the physical path is available. The following
message should be displayed upon success.

5 Click OK to close the Test Connection pop-up and then click DOWNLOAD to download
the configuration files to the module through the path.

ProSoft Technology, Inc. Page 61 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Example 2: Remote Rack Application

For this example, the MVI56E-MNETR module is located in a remote rack accessible
through ControlNet, as shown in the following illustration.

1756-CNB 1756-ENBT
Rack 1

0 1 2 3
Ethernet

ControlNet

1756-CNB MVI56E Module

Rack 2

0 1 2 3 4 5 6

Rack 1
Slot Module Network Address
0 ControlLogix Processor -
1 1756-CNB Node = 1
2 1756-ENBT IP=192.168.0.100
3 Any -

Rack 2
Slot Module Network Address
0 Any -
1 Any -
2 Any -
3 Any -
4 Any -
5 1756-CNB Node = 2
6 MVI56E-MNETR -

ProSoft Technology, Inc. Page 62 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

1 In the Download dialog box, click CIP PATH EDIT.

2 Configure the path as shown in the following illustration and click CONSTRUCT CIP
PATH to build the path in text format.

Click OK to close the CIPconnect Path Editor and return to the Download dialog box.

ProSoft Technology, Inc. Page 63 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

3 Check the new path in the Download dialog box.

4 Click TEST CONNECTION to verify that the physical path is available. The following
message should be displayed upon success.

5 Click DOWNLOAD to download the configuration files to the module through the path.

ProSoft Technology, Inc. Page 64 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Configuring the MVI56E-MNETR Module
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

2.4.2 Using RSWho to Connect to the Module

Note: You need RSLinx installed on your PC to use this feature. You also need an ENBT module set up in
the rack. For information on setting up the ENBT module, see Using CIPconnect to Connect to the Module
(page 57).

1 In the tree view in ProSoft Configuration Builder, right-click the MVI56E-MNETR

module.
2 From the shortcut menu, choose DOWNLOAD FROM PC TO DEVICE.
3 In the Download dialog box, choose 1756 ENBT from the Select Connection Type
dropdown box.

4 Click RSWHO to display modules on the network. The MVI56E-MNETR module will
automatically be identified on the network.

5 Select the module, and then click OK.

6 In the Download dialog box, click DOWNLOAD.

ProSoft Technology, Inc. Page 65 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Ladder Logic
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

3 Ladder Logic
Ladder logic is required for managing communication between the MVI56E-MNETR
module and the processor. The ladder logic handles tasks such as:
• Module backplane data transfer
• Special block handling
• Status data receipt
Additionally, a power-up handler may be needed to initialize the module’s database and
may clear some processor fault conditions.
The sample Import Rung with Add-On Instruction is extensively commented to provide
information on the purpose and function of each user-defined data type and controller
tag. For most applications, the Import Rung with Add-On Instruction will work without
modification.

3.1 Controller Tags

Data related to the MVI56E-MNETR is stored in the ladder logic in variables called
controller tags. Individual controller tags can be grouped into collections of controller
tags called controller tag structures. A controller tag structure can contain any
combination of:
• Individual controller tags
• Controller tag arrays
• Lower-level controller tag structures
The controller tags for the module are pre-programmed into the Add-On Instruction
Import Rung ladder logic. You can find them in the Controller Tags subfolder, located in
the Controller folder in the Controller Organizer pane of the main RSLogix 5000 window.
This controller tag structure is arranged as a tree structure. Individual controller tags are
found at the lowest level of the tree structure. Each individual controller tag is defined to
hold data of a specific type, such as integer or floating-point data. Controller tag
structures are declared with user-defined data types, which are collections of data types.

3.1.1 MVI56E-MNETR Controller Tags

The main controller tag structure, MNETR, is broken down into four lower-level controller
tag structures.

The four lower-level controller tag structures contain other controller tags and controller
tag structures. Click the [+] sign next to any controller tag structure to expand it and view
the next level in the structure.

ProSoft Technology, Inc. Page 66 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Ladder Logic
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

For example, if you expand the MNETR.DATA controller tag structure, you will see that it
contains two controller tag arrays, MNETR.DATA.ReadData and
MNETR.DATA.WriteData, which are 600-element integer arrays by default.

Each controller tag in the Add-On Instruction is commented in the Description column.
Notice that the Data Type column displays the data types used to declare each controller
tag, controller tag array or controller tag structure. Individual controller tags are declared
with basic data types, such as INT and BOOL. Controller tag arrays are declared with
arrays of basic data types. Controller tag structures are declared with user-defined data
types (UDTs).

ProSoft Technology, Inc. Page 67 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Ladder Logic
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

3.2 User-Defined Data Types (UDTs)

User-defined data types (UDTs) allow users to organize collections of data types into
groupings. These groupings, or data type structures, can then be used to declare the
data types for controller tag structures. Another advantage of defining a UDT is that it
may be re-used in other controller tag structures that use the same data types.
The Add-On Instruction Import Rung ladder logic for the module has pre-defined UDTs.
You can find them in the User-Defined subfolder, located in the Data Types folder in the
Controller Organizer pane of the main RSLogix window. Like the controller tags, the
UDTs are organized in a multiple-level tree structure.

3.2.1 MVI56(E)-MNETR User-Defined Data Types

Twelve different UDTs are defined for the MVI56(E)-MNETR Add-On Instruction.
The main UDT, MNETRMODULEDEF, contains all the data types for the module and
was used to create the main controller tag structure, MNETR. There are four UDTs one
level below MNETRMODULEDEF. These lower-level UDTs were used to create the
MNETR.DATA, MNETR.STATUS, MNETR.CONTROL, and MNETR.UTIL controller tag
structures.

Click the [+] signs to expand the UDT structures and view lower-level UDTs.

ProSoft Technology, Inc. Page 68 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Ladder Logic
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

For example, if you expand MNETRDATA, you will see that it contains two UDTs,
ReadData and WriteData. Both of these are 600-element integer arrays by default.

Notice that these UDTs are the data types used to declare the MNETR.DATA.ReadData
and MNETR.DATA.WriteData controller tag arrays.
Each UDT is commented in the Description column.

3.3 Using Controller Tags

You can use controller tags to:
• View read and write data that is being transferred between the module and the
processor.
• View status data for the module.
• Set up and trigger special functions.
• Initiate module restarts (Warm Boot or Cold Boot).

ProSoft Technology, Inc. Page 69 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Ladder Logic
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

3.4 Controller Tag Overview

Controller Tag Description

MNETR.DATA Input and output data transferred between the processor and
the module
MNETR.STATUS Status information
MNETR.CONTROL Governs the data movement between the PLC rack and the
module
MNETR.UTIL Generic tags used for internal ladder processing (DO NOT
MODIFY)

The following sections describe each of these controller tag structures in more detail.

3.4.1 MNETR.DATA
The controller tags in MNETR.DATA hold user data to be transferred between the
processor and the MVI56E-MNETR module. This read and write data is transferred
between the processor and the module as "pages," or blocks, of data up to 40 words
long.
The data types for the MNETR.DATA.ReadData and MNETR.DATA.WriteData controller
tag arrays are integer arrays containing variable numbers of elements.

Controller Tag Data Type Description

ReadData INT[x] Data read from module. Array size is equal
to the Read Register Count set PCB.
WriteData INT[x] Data to write to module. Array size is equal
to the Write Register Count set in PCB.

ProSoft Technology, Inc. Page 70 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Ladder Logic
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

MNETR.DATA.ReadData
For ease of use, this array should be dimensioned as a multiple of 40 words. This data is
paged up to 40 words at a time from the module to the processor. The ladder logic
places the received data into the proper position in the ReadData array.

The ReadData array is related to the contents of the Read Data area of the module's
internal database. To view the actual registers in the module's internal database, access
the database display from ProSoft Configuration Builder's Diagnostics menu. For more
information, see the section on PCB Diagnostics (page 83).

ProSoft Technology, Inc. Page 71 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Ladder Logic
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

MNETR.DATA.WriteData
For ease of use, this array should be dimensioned as a multiple of 40 words. This data is
paged up to 40 words at a time from the processor to the module. The ladder logic
places the write data into the output image for transfer to the module.

The WriteData array is related to the contents of the Write Data area of the module's
internal database. To view the actual registers in the module's internal database, access
the database display from ProSoft Configuration Builder's Diagnostics menu. For more
information, see the section on PCB Diagnostics (page 83).

ProSoft Technology, Inc. Page 72 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Ladder Logic
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

3.4.2 MNETR.STATUS

Name Data Type Description

PassCnt INT Program cycle counter
ProductVersion INT Shows the module software version
ProductCode INT[2] Identifies the module product code
BlockStats MNETRBLOCKSTATS Status information for the data transfer
operations between the processor and the
module
Reserved1 INT Reserved for future use
Reserved2 INT Reserved for future use
MNetReq INT The number of MNET (Port 2000) requests
received
MNetResp INT The number of MNET (Port 2000) responses
sent
MBAPReq INT The number of MBAP (Port 502) requests
received
MBAPResp INT The number of MBAP (Port 502) responses
sent
ClientStatus MNETRCLIENTSTATS Client status data

For a more complete description of the MNETR.STATUS controller tag structure, refer to
the Status Data Definition (page 88).

3.4.3 MNETR.CONTROL
This controller tag structure is used to request special tasks from the module. For more
information, see Special Function Blocks (page 100).

Name Data Type Description

BootTimer TIMER Timer to clear Warm Boot and Cold Boot
WarmBoot BOOL Triggers a Warm Boot
ColdBoot BOOL Triggers a Cold Boot
EventCmdTrigger BOOL Triggers the Event Command.
EventCmd MNETREVENTCMD This object contains the values needed to
build an Event Command. An array of these
objects is used for each port.
CmdControl MNETRCMDCONTROL Controls the execution of the commands listed
in the configuration's MNET Client 0
Command List.
PassThru MNETRPASSTHRU Transfers a remote Client’s commands
through the MNETR module straight into the
processor’s controller tags.
IPAddress MNETRIPADDRESS Getting and setting IP address to and from the
module

ProSoft Technology, Inc. Page 73 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Ladder Logic
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

3.4.4 MNETR.UTIL

Caution: These variables are for internal ladder usage only. Do not use these variables in your own
application, otherwise unpredictable results could occur.

Name Data Type Description

LastRead INT Index of last read block
LastWrite INT Index of last write block
BlockIndex INT Computed block offset for data table
ReadDataSizeGet INT Gets ReadData array length
WriteDataSizeGet INT Gets WriteData array length
ReadDataBlkCount INT Holds the value of the Block Counts of the
ReadData Array. Array size is divided by 40.
WriteDataBlkCount INT Holds the value of the Block Counts of the
WriteData array. Array size is divided by 40.
RBTSremainder INT Holds remainder calculation value from the
ReadData array.
WBTSremainder INT Holds remainder calculation value from the
WriteData array.
IPsetPending BOOL Allows setting module IP address
IPgetPending BOOL Allows getting module IP address
InitOutBlkIDLim INT Block Index Limit for ReadData size of the array

The LastRead tag stores the latest Read Block ID received from the module. The
LastWrite tag stores the latest Write Block ID to be sent to the module. The BlockIndex
tag is an intermediate variable used during the block calculation.

ProSoft Technology, Inc. Page 74 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Diagnostics and Troubleshooting
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

4 Diagnostics and Troubleshooting

The module provides information on diagnostics and troubleshooting in the following
forms:
• LED status indicators on the front of the module provide information on the module’s
status.
• Status data contained in the module can be viewed in ProSoft Configuration Builder
through the Ethernet port.
• Status data values are transferred from the module to the processor.

4.1 LED Status Indicators

4.1.1 Scrolling LED Status Indicators

The scrolling LED display indicates the module's operating status as follows:

Initialization Messages
Code Message
Boot / DDOK Module is initializing
Ladd Module is waiting for required module configuration data from
ladder logic to configure the application port(s)
Waiting for Processor Connection Module did not connect to processor during initialization
▪ Sample ladder logic or AOI is not loaded on processor
▪ Module is located in a different slot than the one
configured in the ladder logic/AOI
▪ Processor is not in RUN or REM RUN mode
Last config: <date> Indicates the last date when the module changed its IP
address. You can update the module date and time through the
module’s web page, or with the optional MVI56E Advanced
Add-On Instruction.
C0 (Client): CmdCnt: X MinDly : After power up and every reconfiguration, the module will
X CmdOffs: X RespTmout : X display the configuration of the application port(s). The
Retries : X ErrOffs : X information consists of:
ARPTmout : X ErrDelay : X Client
FltFlag : X FltSt : X FltOffs : X ▪ CmdCnt : number of commands configured for the Client
SVR (server) : BIOffs: X WIOffs : ▪ MinDly : Minimum Command Delay parameter
X OutOffs : X HoldOffs : X ▪ CmdOffs : Command Error Pointer parameter
FltFlag : X FltSt : X FltSt : X ▪ RespTmout : Response Timeout parameter
CommTmout : X ▪ Retries : Retry Count parameter
▪ ErrOffs : Error/Status Offset parameter
▪ ARPTmout : ARP Timeout parameter
▪ ErrDelay: Command Error Delay parameter
▪ FltFlag: Float Flag parameter
▪ Flt St : Float Start parameter
▪ FltOffs : Float Offset parameter
Server
▪ BIOffs: Bit Input Offset parameter
▪ WIOffs : Word Input Offset parameter
▪ OutOffs : Output offset parameter
▪ HoldOffs : Holding Register offset parameter
▪ FltFlag: Float Flag parameter
▪ FltSt : Float Start parameter
▪ FltOffs : Float Offset parameter

ProSoft Technology, Inc. Page 75 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Diagnostics and Troubleshooting
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Operation Messages
After the initialization step, the following message pattern will be repeated.

<Backplane Status> <IP Address> <Backplane Status> <Port Status>

Code Message
<Backplane Status> OK: Module is communicating with processor
ERR: Module is unable to communicate with processor. For
this scenario, the <Port Status> message above is replaced
with "Processor faulted or is in program mode".
<IP Address> Module IP address
<C0> OK: Port is communicating without error
Communication Errors: port is having communication errors.
Refer to Diagnostics and Troubleshooting (page 75) for further
information about the error.

4.1.2 Ethernet LED Indicators

The Ethernet LEDs indicate the module's Ethernet port status as follows:

LED State Description

10/100 Off No activity on the Ethernet port.
Green Flash The Ethernet port is actively transmitting or receiving data.
LINK/ACT Off No physical network connection is detected. No Ethernet
communication is possible. Check wiring and cables.
Green Solid Physical network connection detected. This LED must be On solid
for Ethernet communication to be possible.

ProSoft Technology, Inc. Page 76 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Diagnostics and Troubleshooting
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

4.1.3 Non-Scrolling LED Status Indicators

The non-scrolling LEDs indicate the module’s operating status as follows:
LED Label Color Status Indication
APP Red or OFF The module is not receiving adequate power or is not securely
Green plugged into the rack. May also be OFF during configuration
download.
GREEN The MVI56E-MNETR is working normally.
RED The most common cause is that the module has detected a
communication error during operation of an application port.
The following conditions may also cause a RED LED:
▪ The firmware is initializing during startup
▪ The firmware detects an on-board hardware problem
during startup
▪ Failure of application port hardware during startup
▪ The module is shutting down
▪ The module is rebooting due to a ColdBoot or WarmBoot
request from the ladder logic or Debug Menu
OK Red or OFF The module is not receiving adequate power or is not securely
Green plugged into the rack.
GREEN The module is operating normally.
RED The module has detected an internal error or is being
initialized. If the LED remains RED for over 10 seconds, the
module is not working. Remove it from the rack and re-insert it
to restart its internal program.
ERR Red OFF The battery voltage is OK and functioning.
ON The battery voltage is low or battery is not present. Allow
battery to charge by keeping module plugged into rack for 24
hours. If ERR LED still does not go off, contact ProSoft
Technology, as the battery is not a user-serviceable item.

4.1.4 Clearing a Fault Condition

Typically, if the OK LED on the front of the module turns RED for more than ten
seconds, a hardware problem has been detected in the module or the program has
exited.
To clear the condition, follow these steps:
1 Turn off power to the rack.
2 Remove the card from the rack.
3 Verify that all jumpers are set correctly.
4 If the module requires a Compact Flash card, verify that the card is installed
correctly.
5 Re-insert the card in the rack and turn the power back on.
6 Verify correct configuration data is being transferred to the module from the
ControlLogix controller.
If the module's OK LED does not turn GREEN, verify that the module is inserted
completely into the rack. If this does not cure the problem, contact ProSoft Technology
Technical Support.

ProSoft Technology, Inc. Page 77 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Diagnostics and Troubleshooting
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

4.1.5 Troubleshooting
Use the following troubleshooting steps if you encounter problems when the module is
powered up. If these steps do not resolve your problem, please contact ProSoft
Technology Technical Support.

Processor Errors
Problem Description Steps to take
Processor Fault Verify that the module is plugged into the slot that has been configured
for the module in the I/O Configuration of RSLogix.
Verify that the slot location in the rack has been configured correctly in
the ladder logic.
Processor I/O LED This indicates a problem with backplane communications. A problem
flashes could exist between the processor and any installed I/O module, not just
the MVI56E-MNETR. Verify that all modules in the rack are correctly
configured in the ladder logic.

Module Errors
Problem Description Steps to take
MVI56E modules with This indicates that backplane transfer operations are failing. Connect to
scrolling LED display: the module’s Configuration/Debug port to check this.
<Backplane Status> To establish backplane communications, verify the following items:
condition reads ERR ▪ The processor is in RUN or REM RUN mode.
▪ The backplane driver is loaded in the module.
▪ The module is configured for read and write data block transfer.
▪ The ladder logic handles all read and write block situations.
▪ The module is properly configured in the processor I/O configuration
and ladder logic.
OK LED remains RED The program has halted or a critical error has occurred. Connect to the
Configuration/Debug port to see if the module is running. If the program
has halted, turn off power to the rack, remove the card from the rack and
re-insert the card in the rack, and then restore power to the rack.

ProSoft Technology, Inc. Page 78 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Diagnostics and Troubleshooting
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

4.2 Using the Diagnostics Menu in ProSoft Configuration Builder

Tip: You can have a ProSoft Configuration Builder Diagnostics window open for more than one module at a
time.

To connect to the module’s Configuration/Debug Ethernet port:

1 In ProSoft Configuration Builder, select the module, and then click the right mouse
button to open a shortcut menu.

2 On the shortcut menu, choose DIAGNOSTICS.

3 In the Diagnostics window, click the SET UP CONNECTION button to browse for the
module’s IP address.

ProSoft Technology, Inc. Page 79 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Diagnostics and Troubleshooting
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

4 In the Connection Setup dialog box, click the TEST CONNECTION button to verify that
the module is accessible with the current settings.

You can also use CIPconnect® to connect to the module through a 1756-ENBT card.
Refer to Using CIPconnect to Connect to the Module (page 57) for information on
how to construct a CIP path.

5 If the Test Connection is successful, click CONNECT.

ProSoft Technology, Inc. Page 80 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Diagnostics and Troubleshooting
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

If PCB is unable to connect to the module:

1 Click the BROWSE DEVICE(S) button to open the ProSoft Discovery Service. Select
the module, then right-click and choose SELECT FOR PCB.

2 Close ProSoft Discovery Service, and click the CONNECT button again.
3 If these troubleshooting steps fail, verify that the Ethernet cable is connected
properly between your computer and the module, either through a hub or switch
(using the grey cable) or directly between your computer and the module (using the
red cable).
If you are still not able to establish a connection, contact ProSoft Technology for
assistance.

ProSoft Technology, Inc. Page 81 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Diagnostics and Troubleshooting
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

4.2.1 Connecting to the Module's Webpage

The module's internal webserver provides access to general product information,
firmware download link, and links to the ProSoft Technology's website.
1 In ProSoft Discovery Service, select the module, and then click the right mouse
button to open a shortcut menu.

2 On the shortcut menu, choose VIEW MODULE’S WEBPAGE.

ProSoft Technology, Inc. Page 82 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Diagnostics and Troubleshooting
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

4.2.2 The Diagnostics Menu

The Diagnostics menu, available through the Ethernet configuration port for this module,
is arranged as a tree structure, with the Main menu at the top of the tree, and one or
more submenus for each menu command. The first menu you see when you connect to
the module is the Main menu.

ProSoft Technology, Inc. Page 83 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Diagnostics and Troubleshooting
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

4.2.3 Monitoring Module Information

Use the MODULE menu to view configuration and hardware information for the MVI56E-
MNETR module’s backplane and Ethernet application port.

Version
Use the Version menu to view module hardware and firmware information.

Config
Use the Configuration menu to view backplane configuration settings for the MVI56E-
MNETR module.
The information on this menu corresponds with the configuration information in the
Module settings in ProSoft Configuration Builder.

NIC Status
Use the NIC Status (Network Interface Card) menu to view configuration and status
information for the MVI56E-MNETR module's Ethernet application port.
The information on this menu is useful for troubleshooting Ethernet network connectivity
problems.

Static ARP
Use the Static ARP menu to view the list of IP and MAC addresses that are configured
not to receive ARP (Address Resolution Protocol) messages from the module.
The Static ARP Table (page 49) defines a list of static IP addresses that the module will
use when an ARP is required.

ProSoft Technology, Inc. Page 84 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Diagnostics and Troubleshooting
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

4.2.4 Monitoring Backplane Information

Use the BACKPLANE menu to view the backplane status information for the MVI56E-
MNETR module.

Backplane Status
Use the Status menu to view current backplane status, including
• Number of retries
• Backplane status
• Fail count
• Number of words read
• Number of words written
• Number of words parsed
• Error count
• Event count
• Command count
During normal operation, the read, write, and parsing values should increment
continuously, while the error value should not increment.
The status values on this menu correspond with members of the Status Data Definition
(page 88).

4.2.5 Monitoring MNET Client Information

Use the MNET CLIENT x menu to view the configuration and status information for the
MNET Client(s).

Config
Use the Configuration menu to view configuration settings for MNET Client x.
The information on this menu corresponds with the configuration information in the
MNET Client x settings in ProSoft Configuration Builder.

Status
Use the Status menu to view status for MNET Client x. During normal operation, the
number of requests and responses should increment, while the number of errors should
not change.

Command List
Use the Command List menu to view the command list settings for MNET Client x. The
information on this menu corresponds with the MNET Client x Commands settings in
ProSoft Configuration Builder. Use the scroll bar on the right edge of the window to view
each MNET Client command.

Command Status
Use the Command Status menu to view MNET Client x Command status.
A zero indicates no error. A non-zero value indicates an error. For an explanation of
each value, refer to Client Command Error (page 90).

ProSoft Technology, Inc. Page 85 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Diagnostics and Troubleshooting
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

4.2.6 Monitoring MNET Server Information

Use the MNET SERVER menu to view the configuration and status information for the
MNET server.

Config
Use the Configuration menu to view configuration settings for MNET servers connected
to the MNET Client.
The information on this menu corresponds with the configuration information in the
MNET Servers settings in ProSoft Configuration Builder (page 47).

Status
Use the Status menu to view the status of each MNET server connected to the MNET
Client 0. During normal operation, the number of requests and responses should
increment, while the number of errors should not change.

4.2.7 Monitoring Database Information

Use the DATABASE menu to view the contents of the MVI56E-MNETR module’s internal
database.
You can view data in the following formats:

ASCII

Decimal

Float

ProSoft Technology, Inc. Page 86 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Diagnostics and Troubleshooting
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Hexadecimal

Use the scroll bar on the right edge of the window to view each page (100 words) of
data.

4.3 Reading Status Data from the Module

Module status information is useful for troubleshooting and can be accessed in several
different ways.

In the ladder logic's MNETR.STATUS controller tag structure.

The MVI56E-MNETR module returns status data in the input image that can be used to
determine the module’s operating status. This data is transferred from the module to the
ControlLogix processor continuously as part of the normal data transfer block sequence
(page 97). You can view this data in the MNETR.STATUS controller tag structure in the
ladder logic. For more information, see the Status Data Definition (page 88).

In ProSoft Configuration Builder's Diagnostics screens.

For more information, see the section on PCB Diagnostics (page 83).

In database locations specified by Error/Status Pointers (optional).

If optional Error/Status Pointers are enabled, the status data can also be found in the
Read Data area of the module’s database at the locations specified by the pointer
configuration parameters. For more information, see Backplane Error/Status Pointer
(page 34), Client Error/Status Pointer (page 38) and Command Error Pointer (page 38).

ProSoft Technology, Inc. Page 87 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Diagnostics and Troubleshooting
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

4.3.1 Status Data Definition

This section contains a description of the controller tags in the MNETR.STATUS
structure, which contains module, server and Client status data.

Controller Tag Description

Pass Count This value is incremented each time a complete program cycle
occurs in the module.
Product Version Shows the module software version.
Product Code Identifies the module product code.
Read Block Count This field contains the total number of Read blocks transferred
from the module to the processor.
Write Block Count This field contains the total number of Write blocks transferred
from the processor to the module.
Parse Block Count This field contains the total number of blocks successfully parsed
that were received from the processor.
Command Event Block Count This field contains the total number of Event Command blocks
received from the processor.
Command Block Count This field contains the total number of command blocks received
from the processor.
Error Block Count This field contains the total number of block errors recognized by
the module.
Reserved1 Not used
Reserved2 Not used
MNet Request Count This counter increments each time a MNet (port 2000) request is
received.
MNet Response Count This counter is incremented each time a MNet (port 2000)
response message is sent.
MBAP Request Count This counter increments each time a MBAP (port 502) request is
received.
MBAP Response Count This counter is incremented each time a MBAP (port 502)
response message is sent.
Client Cmd Request This value is incremented each time a command request is
issued.
Client Cmd Response This value is incremented each time a command response is
received.
Client Cmd Error This value is incremented each time an error message is received
from a remote unit or a local error is generated for a command.

Client Request Count Not used

Client Response Count Not used
Client Error Sent Count Not used
Client Error Received Count Not used
Client Cfg Error Word This word contains a bitmap that defines configuration errors in
the configuration file for the Client.
Client Current Error Code This value corresponds to the current error code for the Client.
Client Last Error Code This value corresponds to the last error code recorded for the
Client.

ProSoft Technology, Inc. Page 88 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Diagnostics and Troubleshooting
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

4.3.2 Client Configuration Error Word

The Configuration Error Word contains Client configuration error indications, in a bit-
mapped format. Specific bits in the module's Configuration Error Word are turned on (set
to 1) to indicate various configuration errors. The Configuration Error Word is a controller
tag in MNETR.STATUS.ClientStatus in the ladder logic.
Bits set to 1 in the Configuration Error Word indicate the following errors.

Bit Description Value

0 Reserved - not currently used 0001h
1 Reserved - not currently used 0002h
2 Reserved - not currently used 0004h
3 Reserved - not currently used 0008h
4 Invalid retry count parameter 0010h
5 The float flag parameter is not valid. 0020h
6 The float start parameter is not valid. 0040h
7 The float offset parameter is not valid. 0080h
8 The ARP Timeout is not in range (ARP Timeout parameter 0 or 0100h
greater than 60000 milliseconds) and will default to 5000
milliseconds.
9 The Command Error Delay is > 300 and will default to 300. 0200h
10 Reserved - not currently used 0400h
11 Reserved - not currently used 0800h
12 Reserved - not currently used 1000h
13 Reserved - not currently used 2000h
14 Reserved - not currently used 4000h
15 Reserved - not currently used 8000h

Combinations of errors will result in more than one bit being set in the error word.
Correct any invalid data in the configuration for proper module operation. A value of zero
(0) in this word indicates all bits are clear, which means that all module configuration
parameters contain valid values. However, this does not mean that the configuration is
valid for the user application. Make sure each parameter is set correctly for the intended
application.

ProSoft Technology, Inc. Page 89 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Diagnostics and Troubleshooting
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

4.3.3 Client Command Errors

There are several different ways to view Client Command Errors.
• In the MNETR.STATUS.ClientStats.CurErr and MNETR.STATUS.ClientStats.LastErr
controller tags
• On the Client status data screens in the ProSoft Configuration Builder Diagnostics
• At a module database location specified by the configuration's MNET Client 0
Command Error Pointer, if the Command Error Pointer is enabled. This means that
the first register refers to command 1 and so on.

Word Offset Description

1 Command 1 Error
2 Command 2 Error
3 Command 3 Error
… ….
… …

For every command that has an error, the module automatically sets the Poll Delay
parameter to the configured value in the Command Error Delay (in seconds). This
instructs the module to wait for X seconds until it attempts to issue the command again.
If set to 0, the module does not use the Command Error Delay and polls based on the
configured Poll Delay in the Client Command list.
As the commands in the Client Command List are polled and executed, an error value is
maintained in the module for each command. This error list can be transferred to the
processor.

Standard Modbus Exception Code Errors

Code Description
1 Illegal function
2 Illegal data address
3 Illegal data value
4 Failure in associated device
5 Acknowledge
6 Busy; message was rejected

Module Communication Error Codes

Code Description
-2 Timeout while transmitting message
-11 Timeout waiting for response after request (same as -36)
253 Incorrect slave/server address in response
254 Incorrect function code in response
255 Invalid CRC/LRC value in response

ProSoft Technology, Inc. Page 90 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Diagnostics and Troubleshooting
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

MNET Client Specific Errors

Code Description
-33 Failed to connect to server specified in command
-35 Invalid length of response message
-36 MNET command response timeout (same as -11)
-37 TCP/IP connection ended before session finished

Command List Entry Errors

Code Description
-40 Too few parameters
-41 Invalid enable code
-42 Internal address > maximum address
-43 Invalid node address (<0 or >255)
-44 Count parameter set to 0
-45 Invalid function code
-46 Invalid swap code
-47 ARP could not resolve MAC from IP (bad IP address, not part of a
network, invalid parameter to ARP routine).
-48 Error during ARP operation: the response to the ARP request did
not arrive to the module after a user-adjustable ARP Timeout.

Note: When the Client gets error -47 or -48, it uses the adjustable ARP Timeout
parameter in the configuration file to set an amount of time to wait before trying again to
connect to this non-existent server. This feature allows the Client to continue sending
commands and polling other existing servers, while waiting for the non-existent server to
appear on the network.

ProSoft Technology, Inc. Page 91 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5 Reference
5.1 Product Specifications
The Modbus TCP/IP Client/Server Enhanced Communication Module with Reduced
Data Block allows Rockwell Automation® ControlLogix® processors to interface easily
with Modbus TCP/IP-compatible devices, such as Modicon Programmable Automation
Controllers (PACs) and a wide variety of Modbus TCP/IP-compatible instruments and
devices.
The MVI56E-MNETR uses a reduced Input/Output (I/O) data image block size for
transferring data between itself and a ControlLogix processor. This makes it ideal for
remote rack applications using ControlNet™ or EtherNet/IP™ process networks. The
module also works well for applications that require redundant ControlLogix processors.
MVI56E-MNETR enhancements include local and remote configuration and diagnostics
through the module’s Ethernet port, and CIPconnect® technology for bridging through
Rockwell Automation ControlNet and EtherNet/IP networks.

5.1.1 General Specifications

• Reduced I/O image size designed specifically to optimize remote
rack implementations
• Backward compatible with previous MVI56-MNETR versions
• Single-slot 1756 ControlLogix backplane-compatible
• 10/100 Mbps auto crossover detection Ethernet port for data transfer and
configuration
• User-definable module data memory mapping of up to 5000 16-bit registers
• CIPconnect-enabled network configuration and diagnostics monitoring using
ControlLogix 1756-ENxT and 1756-CNB modules and EtherNet/IP pass-through
communication
• ProSoft Configuration Builder (PCB) software supported, a Windows-based graphical
user interface providing simple product and network configuration
• Sample ladder logic and Add-On Instructions (AOI) are used for data transfer
between module and processor
• Four-character, alpha-numeric, scrolling LED display of status and diagnostics data
in plain English – no cryptic error or alarm codes to decipher
• ProSoft Discovery Service (PDS) software used to locate the module on the network
and assign temporary IP address
• Personality Module - a non-volatile, industrial-grade Compact Flash (CF) card used
to store network and module configuration, allowing quick in-the-field product
replacement by transferring the CF card

ProSoft Technology, Inc. Page 92 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.1.2 Functional Specifications

• The MVI56E-MNETR transfers data in smaller I/O blocks than the MVI56E-MNET,
which makes it ideal for installations in remote racks or where bandwidth is limited.
• Works well with redundant ControlLogix Programmable Automation Controllers
(PACs) using ControlNet
• Module appears to the ControlLogix processor as an input/output (I/O) module
• 40-word scheduled I/O image blocks used for data transfers allow module to use
significantly less bandwidth than the MVI56E-MNET
• Retrieving module status and executing special functions (Event Commands,
Command Control, etc.) are supported in ladder logic by special block transfer codes

5.1.3 Hardware Specifications

Specification Description
Dimensions Standard 1756 ControlLogix® single-slot module
Backplane current load 800 mA @ 5 Vdc
3 mA @ 24 Vdc
Operating temperature 0°C to 60°C (32°F to 140°F)
Storage temperature -40°C to 85°C (-40°F to 185°F)
Shock 30 g operational
50 g non-operational
Vibration 5 g from 10 Hz to 150 Hz
Relative humidity 5% to 95% (with no condensation)
LED indicators Battery Status (ERR)
Application Status (APP)
Module Status (OK)
4-character, scrolling, Shows module, version, IP, application port
alphanumeric LED display setting, port status, and error information
Ethernet port 10/100 Base-T, RJ45 Connector, for CAT5 cable
Link and Activity LED indicators
Auto-crossover cable detection

ProSoft Technology, Inc. Page 93 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.2 Module Power Up

On power up, the module begins performing the following logical functions:
1 Initialize hardware components
o Initialize ControlLogix backplane driver
o Test and clear all RAM
o Read configuration for module from MNETR.CFG file on Compact Flash Disk
2 Initialize module register space
3 Enable server drivers
4 Enable Client driver
When the module has received the configuration, the module will begin communicating
with other nodes on the network, depending on the configuration.

ProSoft Technology, Inc. Page 94 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.3 Backplane Data Transfer

The MVI56E-MNETR module communicates directly over the ControlLogix backplane.
Data is paged between the module and the ControlLogix processor across the
backplane using the module's input and output images. The update frequency of the
images is determined by the scheduled scan rate defined by the user for the module and
the communication load on the module. Typical update times range from 1 to 10
milliseconds.
This bi-directional transference of data is accomplished by the module putting data in the
input image to send to the processor. Data in the input image is placed in the
processor's controller tags by ladder logic. The input image is set to 42 words.
Processor logic inserts data to the output image to be transferred to the module. The
module's firmware program extracts the data and places it in the module's internal
database. The output image is set to 42 words.
The following illustration shows the data transfer method used to move data between the
ControlLogix processor, the MVI56E-MNETR module and the Modbus TCP/IP Network.

All data transferred between the module and the processor over the backplane is
through the input and output images. Ladder logic must be written in the ControlLogix
processor to interface the input and output image data with data defined in the controller
tags. All data used by the module is stored in its internal database. This database is
defined as a virtual Modbus data table with addresses from 0 (40001 Modbus) to 4999
(45000 Modbus).

ProSoft Technology, Inc. Page 95 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Module’s Internal Database Structure

5000 registers for user data 0

Register Data

4999
Data contained in this database is transferred in blocks, or pages, using the input and
output images. ControlLogix ladder logic and the MVI56E-MNETR module's program
work together to coordinate these block transfers. Up to 40 words of data can be
transferred from the module to the processor (read block - input image) or from the
processor to the module (write block - output image) in each block transfer. The block
structure of each block type depends on the data content and the data transfer function
to be performed by the block. The module uses the following block identification
numbers.

Block Range Descriptions

-1 Status block
0 Status block
1 to 125 Read or Write blocks
1000 to 1124 Initialize Output Data blocks
2000 Event Command block
5001 to 5006 Command Control blocks
9956 Formatted Pass-through block from function 6 or 16 with word data
9957 Formatted Pass-through block from function 6 or 16 with floating-point data
9958 Formatted Pass-through block from function 5
9959 Formatted Pass-through block from function 15
9960 Formatted Pass-through block from function 22
9961 Formatted Pass-through block from function 23
9970 Function 99 indication block
9996 Unformatted Pass-through block with raw Modbus message
9998 Warm-boot block
9999 Cold-boot block

These block identification codes can be broken down into two groups:

Normal data transfer blocks

• Status, Read and Write blocks (-1 to 125)

Special function blocks

• Initialize Output Data blocks (1000 to 1124)
• Event Command block (2000)
• Command Control blocks (5001 to 5006)
• Pass-through blocks (9956 to 9961, 9970 and 9996)
• Module IP Address blocks (9990 and 9991)
• Warm-boot and Cold-boot blocks (9998 and 9999)

ProSoft Technology, Inc. Page 96 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.3.1 Normal Data Transfer Blocks

Normal data transfer includes the paging of user data between the processor's data
areas and the module’s internal database (registers 0 to 4999), as well as the paging of
status data. These data are transferred through Read (input image), Write (output
image) and Status blocks. The data is paged 40 words at a time.
During normal program operation, the module sequentially sends Read and Status Data
blocks and receives Write blocks. The Status block is first in the sequence, followed by
alternating Write and Read blocks.
As an example, assume that an application's Read Data area consists of 120 words and
its Write Data area consists of 80 words. Since the Read and Write data is paged 40
words at a time, the module will use 3 Read blocks and 2 Write blocks to transfer the
data. The Read, Write and Status blocks will be sequenced as follows.

This sequence will continue until interrupted by other special function blocks sent by the
processor, by a command request from a node on the Modbus network, or by operator
control through the module’s Configuration/Debug port.
The following topics describe the function and structure of each block.

ProSoft Technology, Inc. Page 97 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Read Block
These blocks of data transfer information from the module to the ControlLogix processor.
The following table describes the structure of the input image.

Read Block from Module to Processor

Word Offset Description Length
0 Write Block ID 1
1 to 40 Read Data 40
41 Read Block ID 1

The Read Block ID is an index value used to determine where the 40 words of data from
module memory will be placed in the ReadData[x] controller tag array of the
ControlLogix. Each transfer can move up to 40 words (block offsets 1 to 40) of data.

Write Block
These blocks of data transfer information from the ControlLogix processor to the module.
The following table describes the structure of the output image.

Write Block from Processor to Module

Word Offset Description Length
0 Write Block ID 1
1 to 40 Write Data 40
41 Spare 1

The Write Block ID is an index value used to determine the location in the module’s
database where the data will be placed. Each transfer can move up to 40 words (block
offsets 1 to 40) of data.

ProSoft Technology, Inc. Page 98 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Status Block
The Status block is automatically copied from the module into the MNETR.STATUS
controller tag structure when the block ID is 0 or -1, and contains status information
about the module. For more information, see the Status Data Definition (page 88).

Status Block from Module to Processor

Word Offset Description Length
0 Write Block ID 1
1 Program Scan Counter 1
2 to 7 Block Transfer Status 6
8 to 9 Reserved Server Status 2
10 to 11 MNET Server Status 2
12 to 13 MBAP Server Status 2
14 to 23 MNET Client Status 10
24 to 25 Product Name 2
26 Product Version 1
27 to 40 Reserved 14
41 Read Block ID (-1 or 0) 1

Client Status Data

Word Offset Client Status
14 Total number of command list requests
15 Total number of command list responses
16 Total number of command list errors
17 Not used
18 Not used
19 Not used
20 Not used
21 Configuration Error Word
22 Current Error
23 Last Error

ProSoft Technology, Inc. Page 99 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.3.2 Special Function Blocks

Special function blocks are optional blocks used to request special tasks from the
module.

Initialize Output Data Blocks (1000 to 1124)

Use the Initialize Output Data parameter in the configuration to bring the module to a
known state after a restart operation. If the Initialize Output Data parameter is enabled,
when the module performs a restart operation, it will request blocks of output data from
the ReadData array in the processor to initialize the Read Data area of the module’s
internal database.

Normal Data transfer Initialize Output Data transfer

CLX Processor MNET Module CLX Processor MNET Module

Modbus Read Modbus

Read Local:X:I
Local:X:I Output Tags Output
Tags

Write Write
Local:X:O Modbus Modbus
Tags Tags Local:X:O
Input Input

Block Request from Module to Processor

Word Offset Description Length
0 1000 to 1124 1
1 to 40 Spare 40
41 1000 to 1124 1

The block number in word 0 of the block determines the data set of up to 40 output
words to transfer from the processor. Ladder logic in the processor must recognize these
blocks and place the correct information in the output image to be returned to the
module.

Block Response from Processor to Module

Word Offset Description Length
0 1000 to 1124 1
1 to 40 Output Data to preset in module. 40
41 Spare 1

ProSoft Technology, Inc. Page 100 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Event Command Block (2000)

Note: Event Commands are not needed for normal Modbus command list polling operations and are
needed only occasionally for special circumstances.

During routine operation, the module continuously cycles through the user-defined
MNET Client 0 Command List (page 40), examining commands in the order they are
listed and sending enabled commands on the network. However, the module also has a
special command priority queue, which is an internal buffer that holds commands from
special function blocks until they can be sent on the network.
When one or more commands appear in the command priority queue:
1 The routine polling process is temporarily interrupted.
2 The commands in the command priority queue are executed until the queue is
empty.
3 Then the module goes back to where it left off on the MNET Client 0 Command List
and continues routine polling.
Event Command blocks send Modbus TCP/IP commands directly from controller tags by
ladder logic to the Client command priority queue on the module. Event Commands are
not placed in the module's internal database and are not part of the MNET Client 0
Command List.

ProSoft Technology, Inc. Page 101 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Block Request from Processor to Module

Word Offset Description
0 Block ID - This word contains the block 2000 identification code to indicate that
the block contains a command to execute by the Client driver.
1 to 4 IP Address - These words contain the IP address for the server the message is
intended for. Each digit (0 to 255) of the IP address is placed in one of the four
registers. For example, to reach IP address 192.168.0.100, enter the following
values in words 1 to 4: 192, 168, 0 and 100. The module will construct the
normal dotted IP address from the values entered. The values entered will be
added with the mask 0x00ff to ensure the values are in the range of 0 to 255.
5 Service Port - This word contains the TCP service port the message will be
interfaced with. For example, to interface with a MBAP device, the word should
contain a value of 502. To interface with a MNET device, a value of 2000
should be utilized. Any value from 0 to 65535 is permitted. A value of 502 will
cause a MBAP formatted message to be generated. All other values will
generate an encapsulated Modbus message.
6 Slave Address - This word contains the Modbus node address for the
message. This field should have a value from 0 to 41.
7 Internal DB Address - This word contains the internal Modbus address in the
module to use with the command. This word can contain a value from 0 to
4999.
8 Point Count - This word contains the count parameter that determines the
number of digital points or registers to associate with the command.
9 Swap Code - The parameter specifies the swap type for the data. This function
is only valid for function codes 3 and 4.
10 Modbus Function Code - This word contains the Modbus function code for the
command.
11 Device Database Address - This word contains the Modbus address in the
server device to be associated with the command.
12 to 41 Spare

When the module receives this request block, it builds the command, places the
command in the command priority queue (if the queue is not already full; maximum
capacity is 100 commands), and returns a response block to tell the ladder logic whether
or not the command has been successfully added to the queue.

Block Response from Module to Processor

Word Offset Description Length
0 Write Block ID 1
1 0=Fail, 1=Success 1
2 to 40 Spare 39
41 2000 1

Word 2 of the block can be used by the ladder logic to determine whether or not the
command was successfully added to the command priority queue. The command will fail
if the queue for the port is already full at the time when the Event Command block is
received by the module.

ProSoft Technology, Inc. Page 102 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Controller Tags
The elements of the MNETR.CONTROL.EventCmd controller tag array contain all the
values needed to build one Modbus TCP/IP command, have it sent to the module, and
control the processing of the returned response block.

Name Data Type Description

IP0 INT First digit of IP address
IP1 INT Second digit of IP address
IP2 INT Third digit of IP address
IP3 INT Last digit of IP address
ServPort INT TCP Service Port number (0-65535), 502 for
MBAP, 2000 for MNET
Node INT Modbus slave node address (0 to 247)
DBAddress INT Module internal database for message
Count INT Register or data point count
Swap INT Swap code for functions 3 and 4
Function INT Modbus function code for message
Address INT Address to interface with in device
Result INT Shows the result of the event that was sent

Command Control Blocks (5001 to 5006)

Note: Command Control is not needed for normal Modbus command list polling operations and are needed
only occasionally for special circumstances.

During routine operation, the module continuously cycles through the user-defined
MNET Client 0 Command List (page 40), examining commands in the order they are
listed and sending enabled commands on the network. However, the module also has a
special command priority queue, which is an internal buffer that holds commands from
special function blocks until they can be sent on the network.
When one or more commands appear in the command priority queue:
1 The routine polling process is temporarily interrupted.
2 The commands in the command priority queue are executed until the queue is
empty.
3 Then the module goes back to where it left off on the MNET Client 0 Command List
and continues routine polling.
Like Event Command blocks, Command Control blocks place commands into the
module’s command priority queue. Unlike Event Commands blocks, which contain all the
values needed for one command, Command Control is only used with commands
already defined in the MNET Client 0 Command List.

ProSoft Technology, Inc. Page 103 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Commands in the MNET Client 0 Command List may be either enabled for routine
polling or disabled and excluded from routine polling. A disabled command has its
Enable parameter set to NO (0) and is skipped during routine polling. An enabled
command has its Enable parameter set to YES (1) and is sent during routine polling.
However, Command Control allows any command in the predefined MNET Client 0
Command List to be added to the command priority queue, whether it is enabled for
routine polling or not.
Command Control also gives you the option to use ladder logic to have commands from
the MNET Client 0 Command List executed at a higher priority and out of routine order, if
such an option might be required in special circumstances.
A single Command Control block request can place up to six commands from the MNET
Client 0 Command List into the command priority queue.

Block Request from Processor to Module

Word Offset Description Length
0 Command Control block identification code of 5001 to 5006. 1
The rightmost digit indicates the number of commands (1 to
6) to add to the command priority queue.
1 This word contains the Command Index for the first 1
command to be entered into the queue.
2 This word contains the Command Index for the second 1
command to be entered into the queue.
3 This word contains the Command Index for the third 1
command to be entered into the queue.
4 This word contains the Command Index for the fourth 1
command to be entered into the queue.
5 This word contains the Command Index for the fifth
command to be entered into the queue.
6 This word contains the Command Index for the sixth 1
command to be entered into the queue.
7 to 41 Spare 35

The last digit in the block identification code indicates the number of commands to
process. For example, a block identification code of 5003 indicates that three commands
are to be placed in the queue. In this case, the first three of the six available Command
Indexes will be used to determine exactly which three commands will be added to the
queue, and to set their order of execution.
Values to enter for the six Command Indexes range from 0 to 99 and correspond to the
MNET Client 0 Command List entries, which are numbered from 1 to 100. To determine
the Command Index value, subtract one (1) from the row number of the command in the
MNET Client 0 Command List, as seen in the Command Editor window of ProSoft
Configuration Builder (PCB).
The module responds to a Command Control block request with a response block,
indicating the number of commands added to the command priority queue.

ProSoft Technology, Inc. Page 104 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Block Response from Module to Processor

Word Offset Description Length
0 Write Block ID 1
1 Number of commands added to command priority queue 1
2 to 40 Spare 39
41 This word contains the Block ID 5001 to 5006 requested by 1
the processor.

Controller Tags
The MNETR.CONTROL.CmdControl controller tag array holds all the values needed to
create one Command Control block, have it sent to the module, and control the
processing of the returned response block.

Name Data Type Description

CmdIndex INT[6] Enter the ROW NUMBER of the command in the
MNET Client 0 Command List in Prosoft
Configuration Builder minus 1. This is a six-element
array. Each element holds one Command
Index.and to execute from the Client command list.
NumberOfCommands INT Enter a decimal value representing the quantity of
commands to be requested in the Command
Control block (1 to 6).
CommandsAddedtoQueue INT Returned decimal value representing the quantity of
commands added from the MNET Client 0
Command List to the command priority queue by
the most recent Command Control block.
CmdControlTrigger BOOL Set this tag to 1 to trigger the execution of a
command after all the other parameters have been
entered.

ProSoft Technology, Inc. Page 105 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Pass-Through Blocks (9956 to 9961, 9970 and 9996)

In Pass-Through mode, write messages sent to a server port are passed directly through
to the processor. In this mode, the module sends special blocks to the processor when a
write request is received from a Client. Ladder logic must handle the receipt of these
blocks and place the enclosed data into the proper controller tags in the processor.
There are two basic modes of operation when the pass-through feature is utilized:
Unformatted (code 1) and Formatted (code 2 or 3). In the unformatted mode, messages
received on the server are passed directly to the processor without any processing.
These unformatted blocks require more decoding than the formatted blocks.
The Modbus protocol supports control of binary output (coils - functions 5 and 15) and
registers (functions 6 and 16).
Any Modbus function 5, 6, 15 or 16 commands will be passed from the server to the
processor using the block identification numbers 9956 to 9961, 9970 and 9996.

Formatted Pass-Through Blocks

In formatted pass-through mode, the module processes the received write request and
generates a special block dependent on the function received. There are two modes of
operation when the formatted pass-through mode is selected. If code 2 is utilized (bytes
swapped), the data received in the message is presented in the order expected by the
processor. If code 3 is utilized (no swap), the bytes in the data area of the message will
be swapped. This selection is applied to all received write requests. The block
identification code used with the request depends on the Modbus function requested.

Block ID Modbus Function

9956 6, 16 (word type data)
9957 6, 16 (floating-point)
9958 5
9959 15
9960 22
9961 23
9970 99

Pass-Through Blocks 9956, 9957, 9958, 9960 and 9961 from Module to Processor
Word Offset Description Length
0 9956, 9957, 9958, 9960 or 9961 1
1 Number of word registers in Modbus data set 1
2 Starting address for Modbus data set 1
3 to 40 Modbus data set 38
41 9956, 9957, 9958, 9960 or 9961 1

ProSoft Technology, Inc. Page 106 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Pass-Through Block 9959 from Module to Processor

Word Offset Description Length
0 9959 1
1 Number of word registers in Modbus data set 1
2 Starting word address for Modbus data set 1
3 to 21 Modbus data set 19
22 to 40 Bit mask for the data set. Each bit to be considered with the 19
data set will have a value of 1 in the mask. Bits to ignore in
the data set will have a value of 0 in the mask.
41 9959 1

Pass-Through Block 9970 from Module to Processor

Word Offset Description Length
0 9970 1
1 1 1
2 0 1
3 to 40 Spare data area 38
41 9996 1

The ladder logic should copy and parse the received message and control the processor
as expected by the Client device. The processor responds to the formatted pass-through
blocks with a write block.

Response Blocks 9956, 9957, 9958, 9959, 9960, 9961 or 9970 from Processor to
Module
Word Offset Description Length
0 9956, 9957, 9958, 9959, 9960, 9961 or 9970 1
1 to 41 Spare data area 41

Unformatted Pass-Through Blocks

When the unformatted pass-through mode (code 1) is selected, information is passed
from the module to the processor with a block identification code of 9996. Word 2 of this
block contains the length of the message, and the message starts at word 3. Other
controller tags are required to store the controlled values contained in these messages.

ProSoft Technology, Inc. Page 107 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Pass-Through Block 9996 from Module to Processor

Word Offset Description Length
0 9996 1
1 Number of bytes in Modbus msg 1
2 Reserved (always 0) 1
3 to 40 Modbus message received 38
41 9996 1

The ladder logic should copy and parse the received message and control the processor
as expected by the Client device. The processor responds to the pass-through block
with a write block.

Response Block 9996 from Processor to Module

Word Offset Description Length
0 9996 1
1 to 41 Spare 41

This informs the module that the command has been processed and can be cleared
from the pass-through queue.

Set Module IP Address Block (9990)

Block Request from Processor to Module

Word Offset Description Length
0 9990 1
1 First digit of dotted IP address 1
2 Second digit of dotted IP address 1
3 Third digit of dotted IP address 1
4 Last digit of dotted IP address 1
5 to 41 Reserved 36

Block Response from Module to Processor

Word Offset Description Length
0 0 1
1 Write Block ID 1
2 First digit of dotted IP address 1
3 Second digit of dotted IP address 1
4 Third digit of dotted IP address 1
5 Last digit of dotted IP address 1
6 to 41 Spare data area 35

ProSoft Technology, Inc. Page 108 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Get Module IP Address Block (9991)

Block Request from Processor to Module

Word Offset Description Length
0 9991 1
1 to 41 Spare data area 40

Block Response from Module to Processor

Word Offset Description Length
0 0 1
1 Write Block ID 1
2 First digit of dotted IP address 1
3 Second digit of dotted IP address 1
4 Third digit of dotted IP address 1
5 Last digit of dotted IP address 1
6 to 41 Spare data area 35

Warm Boot Block (9998)

This block is sent from the ControlLogix processor to the module (output image) when
the module is required to perform a warm-boot (software reset) operation. This block is
commonly sent to the module any time configuration data modifications are made in the
controller tags data area. This will cause the module to read the new configuration
information and to restart.

Block Request from Processor to Module

Word Offset Description Length
0 9998 1
1 to 41 Spare 41

Cold Boot Block (9999)

This block is sent from the ControlLogix processor to the module (output image) when
the module is required to perform the cold boot (hardware reset) operation. This block is
sent to the module when a hardware problem is detected by the ladder logic that
requires a hardware reset.

Block Request from Processor to Module

Word Offset Description Length
0 9999 1
1 to 41 Spare 41

ProSoft Technology, Inc. Page 109 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.4 Data Flow between MVI56E-MNETR and ControlLogix Processor

The following topics describe the flow of data between the two pieces of hardware
(ControlLogix processor and MVI56E-MNETR module) and other nodes on the Modbus
TCP/IP network under the module’s different operating modes. The module has both
server and Client capability. The server accepts TCP/IP connections on service ports
502 (MBAP) (10 server connections) and 2000 (MNET) (10 server connections). The
Client can generate either MBAP or MNET requests dependent on the service port
selected in the command.

The following topics discuss the operation of the server and Client drivers.

ProSoft Technology, Inc. Page 110 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.4.1 Server Driver

The server driver allows the MVI56E-MNETR module to respond to data read and write
commands issued by Clients on the Modbus TCP/IP network. The following illustration
describes the flow of data into and out of the module.

1 The server driver receives the configuration information from the configuration file on
the Personality Module (compact flash card, and the module initializes the server.
2 A Client device, such as a Modicon PLC or an HMI application, issues a read or write
command to the module’s node address. The server driver validates the message
before accepting it into the module. If the message is considered invalid, an error
response is returned to the originating Client node.
3 After the module accepts the command, the module processes the data contained in
the command.
If the command is a read command, the data is read out of the database and a
response message is built.
If the command is a write command, the data is written directly into the database and
a response message is built.
If the command is a write command and the pass-through feature is utilized, the write
message is transferred to the processor ladder logic and is not written directly into
the module’s database, unless it is returned as a change in the output image that
overwrites data in the WriteData area as a result of such ladder logic processing.
4 When the data processing has been completed in Step 3, the response is issued to
the originating Client node.
5 Counters are available in the Status Block that permit the ladder logic program to
determine the level of activity of the server driver.

ProSoft Technology, Inc. Page 111 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

After the server socket is open, it must receive messages within a one minute period, or
else it will close the socket. After closing, the socket will be reused.
An exception to normal processing is when the pass-through mode is implemented. In
this mode, all write requests are passed directly to the processor and are not placed in
the database. This permits direct, remote control of the processor without changes in the
intermediate database. This mode is especially useful for Client devices that do not send
both states of control. For example, a SCADA system may only send a SET command to
a digital control point and never send a CLEAR command to that same digital point
address because it expects the processor logic to reset the control bit. Pass-through
must be used to simulate this mode. The following illustration shows the data flow for a
server port with pass-through enabled.

ProSoft Technology, Inc. Page 112 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.4.2 Client Driver

In the Client driver, the MVI56E-MNETR module issues read or write commands to
servers on the Modbus TCP/IP network. The commands originate either from the
module's user-configured Client 0 Command List, or directly from the processor as Event
Commands. The commands from the Client 0 Command List are executed either via
routine polling or as a result of special Command Control block requests from the
processor. The following flowchart describes the flow of data into and out of the module.

1 The Client driver obtains configuration data when the module restarts. This includes
the timeout parameters and the Command List. These values are used by the driver
to determine the type of commands to be issued to the other nodes on the Modbus
TCP/IP network.
2 When configured, the Client driver begins transmitting read and/or write commands
to the other nodes on the network. The data for write commands is obtained from the
module's internal database.
3 Assuming successful processing by the node specified in the command, a response
message is received into the Client driver for processing.

ProSoft Technology, Inc. Page 113 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

4 Data received from the server is passed into the module's internal database, if the
command was a read command.
5 Status information is routinely sent to the processor in a special Status block among
with the Read data blocks in the normal data transfer sequence.
6 Special functions, such as Event Commands and Command Control options, can be
generated by the processor and sent to the Client driver for action.

Client Command List

In order for the Client to function, the module's MNET Client x Command List must be
defined in the configuration. This list contains up to 100 individual entries, with each
entry containing the information required to construct a valid command. This includes the
following:
• Command enable mode
o (0) disabled
o (1) continuous
o (2) conditional
• IP address and service port to connect to on the remote server
• Slave Node Address
• Command Type - Read or Write up to 100 words per command
• Database Source and Destination Register Address - Determines where data will be
placed and/or obtained
• Count - Selects the number of words to be transferred - 1 to 100
• Poll Delay - 1/10th seconds
For information on troubleshooting commands, see Client Command Errors (page 90).

ProSoft Technology, Inc. Page 114 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.5 Ethernet Cable Specifications

The recommended cable is Category 5 or better. A Category 5 cable has four twisted
pairs of wires, which are color-coded and cannot be swapped. The module uses only
two of the four pairs.
The Ethernet ports on the module are Auto-Sensing. You can use either a standard
Ethernet straight-through cable or a crossover cable when connecting the module to an
Ethernet hub, a 10/100 Base-T Ethernet switch, or directly to a PC. The module will
detect the cable type and use the appropriate pins to send and receive Ethernet signals.
Ethernet cabling is like U.S. telephone cables, except that it has eight conductors. Some
hubs have one input that can accept either a straight-through or crossover cable,
depending on a switch position. In this case, you must ensure that the switch position
and cable type agree.
Refer to Ethernet cable configuration (page 115) for a diagram of how to configure
Ethernet cable.

5.5.1 Ethernet Cable Configuration

Note: The standard connector view shown is color-coded for a straight-through cable.

Crossover cable Straight- through cable

RJ-45 PIN RJ-45 PIN RJ-45 PIN RJ-45 PIN
1 Rx+ 3 Tx+ 1 Rx+ 1 Tx+
2 Rx- 6 Tx- 2 Rx- 2 Tx-
3 Tx+ 1 Rx+ 3 Tx+ 3 Rx+
6 Tx- 2 Rx- 6 Tx- 6 Rx-

5.5.2 Ethernet Performance

Ethernet performance on the MVI56E-MNETR module can affect the operation of the
MNETR application ports in the following ways.
• Accessing the web interface (refreshing the page, downloading files, and so on) may
affect MNETR performance
• High Ethernet traffic may impact MNETR performance (consider CIPconnect (page
57) for these applications and disconnect the module Ethernet port from the
network).

ProSoft Technology, Inc. Page 115 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.6 Modbus Protocol Specification

The following pages give additional reference information regarding the Modbus protocol
commands supported by the MVI56E-MNETR.

5.6.1 About the Modbus TCP/IP Protocol

Modbus is a widely used protocol originally developed by Modicon in 1978. Since that
time, the protocol has been adopted as a standard throughout the automation industry.
The original Modbus specification uses a serial connection to communicate commands
and data between Client and server devices on a network. Later enhancements to the
protocol allow communication over Ethernet networks using TCP/IP as a "wrapper" for
the Modbus protocol. This protocol is known as Modbus TCP/IP.
Modbus TCP/IP is a Client/server protocol. The Client establishes a connection to the
remote server. When the connection is established, the Client sends the Modbus TCP/IP
commands to the server. The MVI56E-MNETR module works both as a Client and as a
server.
Aside from the benefits of Ethernet versus serial communications (including
performance, distance, and flexibility) for industrial networks, the Modbus TCP/IP
protocol allows for remote administration and control of devices over a TCP/IP network.
The efficiency, scalability, and low cost of a Modbus TCP/IP network make this an ideal
solution for industrial applications.
The MVI56E-MNETR module acts as an input/output module between devices on a
Modbus TCP/IP network and the Rockwell Automation backplane. The module uses an
internal database to pass data and commands between the processor and the Client
and server devices on the Modbus TCP/IP network.

ProSoft Technology, Inc. Page 116 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.6.2 Commands Supported by the Module

The format of each command in the list depends on the Modbus Function Code being
executed.
The following table lists the functions supported by the module.

Function Code Definition Supported in Client Supported in Server

1 Read Coil Status X X
2 Read Input Status X X
3 Read Holding Registers X X
4 Read Input Registers X X
5 Set Single Coil X X
6 Single Register Write X X
7 Read Exception Status X
8 Diagnostics X
15 Multiple Coil Write X X
16 Multiple Register Write X X
22 Mask Write 4X X
23 Read/Write X

Each command list record has the same general format. The first part of the record
contains the information relating to the communication module and the second part
contains information required to interface to the Modbus TCP/IP server device.

ProSoft Technology, Inc. Page 117 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.6.3 Read Coil Status (Function Code 01)

Query
This function allows the user to obtain the ON/OFF status of logic coils used to control
discrete outputs from the addressed server only. Broadcast mode is not supported with
this function code. In addition to the server address and function fields, the message
requires that the information field contain the initial coil address to be read (Starting
Address) and the number of locations that will be interrogated to obtain status data.
The addressing allows up to 2000 coils to be obtained at each request; however, the
specific server device may have restrictions that lower the maximum quantity. The coils
are numbered from zero; (coil number 1 = zero, coil number 2 = one, coil number 3 =
two, and so on).
The following table is a sample read output status request to read coils 0020 to 0056
from server device number 11.

Adr Func Data Start Pt Data Start Pt Data # Of Pts Data # Of Pts Error Check
Hi Lo Ho Lo Field
11 01 00 13 00 25 CRC

Response
An example response to Read Coil Status is as shown in Figure C2. The data is packed
one bit for each coil. The response includes the server address, function code, quantity
of data characters, the data characters, and error checking. Data will be packed with one
bit for each coil (1 = ON, 0 = OFF). The low order bit of the first character contains the
addressed coil, and the remainder follow. For coil quantities that are not even multiples
of eight, the last characters will be filled in with zeros at high order end. The quantity of
data characters is always specified as quantity of RTU characters, that is, the number is
the same whether RTU or ASCII is used.
Because the server interface device is serviced at the end of a controller's scan, data will
reflect coil status at the end of the scan. Some servers will limit the quantity of coils
provided each scan; thus, for large coil quantities, multiple PC transactions must be
made using coil status from sequential scans.

Addr Func Byte Data Coil Data Coil Data Coil Data Coil Data Coil Error
Count Status 20 Status 28 to Status 36 to Status 44 to Status 52 to Check
to 27 35 43 51 56 Field
11 01 05 CD 6B B2 OE 1B CRC

The status of coils 20 to 27 is shown as CD(HEX) = 1100 1101 (Binary). Reading left to
right, this shows that coils 27, 26, 23, 22, and 20 are all on. The other coil data bytes are
decoded similarly. Due to the quantity of coil statuses requested, the last data field,
which is shown 1B (HEX) = 0001 1011 (Binary), contains the status of only 5 coils (52 to
56) instead of 8 coils. The 3 left most bits are provided as zeros to fill the 8-bit format.

ProSoft Technology, Inc. Page 118 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.6.4 Read Input Status (Function Code 02)

Query
This function allows the user to obtain the ON/OFF status of discrete inputs in the
addressed server PC Broadcast mode is not supported with this function code. In
addition to the server address and function fields, the message requires that the
information field contain the initial input address to be read (Starting Address) and the
number of locations that will be interrogated to obtain status data.
The addressing allows up to 2000 inputs to be obtained at each request; however, the
specific server device may have restrictions that lower the maximum quantity. The inputs
are numbered form zero; (input 10001 = zero, input 10002 = one, input 10003 = two, and
so on, for a 584).
The following table is a sample read input status request to read inputs 10197 to 10218
from server number 11.

Addr Func Data Start Pt Data Start Pt Data #of Pts Data #of Pts Error Check Field
Hi Lo Hi Lo
11 02 00 C4 00 16 CRC

Response
An example response to Read Input Status is as shown in Figure C4. The data is
packed one bit for each input. The response includes the server address, function code,
quantity of data characters, the data characters, and error checking. Data will be packed
with one bit for each input (1=ON, 0=OFF). The lower order bit of the first character
contains the addressed input, and the remainder follow. For input quantities that are not
even multiples of eight, the last characters will be filled in with zeros at high order end.
The quantity of data characters is always specified as a quantity of RTU characters, that
is, the number is the same whether RTU or ASCII is used.
Because the server interface device is serviced at the end of a controller's scan, data will
reflect input status at the end of the scan. Some servers will limit the quantity of inputs
provided each scan; thus, for large coil quantities, multiple PC transactions must be
made using coil status for sequential scans.

A Func Byte Data Discrete Data Discrete Data Discrete Error Check
d Count Input 10197 to Input 10205 to Input 10213 to Field
d 10204 10212 10218
r
1 02 03 AC DB 35 CRC
1

The status of inputs 10197 to 10204 is shown as AC (HEX) = 10101 1100 (binary).
Reading left to right, this show that inputs 10204, 10202, and 10199 are all on. The other
input data bytes are decoded similar.
Due to the quantity of input statuses requested, the last data field which is shown as 35
HEX = 0011 0101 (binary) contains the status of only 6 inputs (10213 to 102180) instead
of 8 inputs. The two left-most bits are provided as zeros to fill the 8-bit format.

ProSoft Technology, Inc. Page 119 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.6.5 Read Holding Registers (Function Code 03)

Query
Read Holding Registers (03) allows the user to obtain the binary contents of holding
registers 4xxxx in the addressed server. The registers can store the numerical values of
associated timers and counters which can be driven to external devices. The addressing
allows up to 125 registers to obtained at each request; however, the specific server
device may have restriction that lower this maximum quantity. The registers are
numbered form zero (40001 = zero, 40002 = one, and so on). The broadcast mode is
not allowed.
The example below reads registers 40108 through 40110 from server 584 number 11.

Addr Func Data Start Reg Data Start Reg Data #of Data #of Regs Error Check
Hi Lo Regs Hi Lo Field
11 03 00 6B 00 03 CRC

Response
The addressed server responds with its address and the function code, followed by the
information field. The information field contains 1 byte describing the quantity of data
bytes to be returned. The contents of the registers requested (DATA) are two bytes
each, with the binary content right justified within each pair of characters. The first byte
includes the high order bits and the second, the low order bits.
Because the server interface device is normally serviced at the end of the controller's
scan, the data will reflect the register content at the end of the scan. Some servers will
limit the quantity of register content provided each scan; thus for large register
quantities, multiple transmissions will be made using register content from sequential
scans.
In the example below, the registers 40108 to 40110 have the decimal contents 555, 0,
and 100 respectively.

Addr Func ByteCnt Hi Data Lo Hi Data Lo Hi Data Lo Error Check

Data Data Data Field
11 03 06 02 2B 00 00 00 64 CRC

ProSoft Technology, Inc. Page 120 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.6.6 Read Input Registers (Function Code 04)

Query
Function code 04 obtains the contents of the controller's input registers at addresses
3xxxx. These locations receive their values from devices connected to the I/O structure
and can only be referenced, not altered from within the controller, The addressing allows
up to 125 registers to be obtained at each request; however, the specific server device
may have restrictions that lower this maximum quantity. The registers are numbered for
zero (30001 = zero, 30002 = one, and so on). Broadcast mode is not allowed.
The example below requests the contents of register 3009 in server number 11.

Addr Func Data Start Data Start Reg Data #of Regs Data #of Regs Error Check
Reg Hi Lo Hi Lo Field
11 04 00 08 00 01 CRC

Response
The addressed server responds with its address and the function code followed by the
information field. The information field contains 1 byte describing the quantity of data
bytes to be returned. The contents of the registers requested (DATA) are 2 bytes each,
with the binary content right justified within each pair of characters. The first byte
includes the high order bits and the second, the low order bits.
Because the server interface is normally serviced at the end of the controller's scan, the
data will reflect the register content at the end of the scan. Each PC will limit the quantity
of register contents provided each scan; thus for large register quantities, multiple PC
scans will be required, and the data provided will be form sequential scans.
In the example below the register 3009 contains the decimal value 0.

Addr Func Byte Data Input Reg Hi Data Input Reg Lo Error Check Field
Count
11 04 02 00 00 E9

ProSoft Technology, Inc. Page 121 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.6.7 Force Single Coil (Function Code 05)

Query
This message forces a single coil either ON or OFF. Any coil that exists within the
controller can be forced to either state (ON or OFF). However, because the controller is
actively scanning, unless the coil is disabled, the controller can also alter the state of the
coil. Coils are numbered from zero (coil 0001 = zero, coil 0002 = one, and so on). The
data value 65,280 (FF00 HEX) will set the coil ON and the value zero will turn it OFF; all
other values are illegal and will not affect that coil.
The use of server address 00 (Broadcast Mode) will force all attached servers to modify
the desired coil.

Note: Functions 5, 6, 15, and 16 are the only messages that will be recognized as valid for broadcast.

The example below is a request to server number 11 to turn ON coil 0173.

Addr Func Data Coil # Data Coil # Data On/Off Data Error Check Field
Hi Lo Ind
11 05 00 AC FF 00 CRC

Response
The normal response to the Command Request is to re-transmit the message as
received after the coil state has been altered.

Addr Func Data Coil # Data Coil # Data On/ Data Error Check Field
Hi Lo Off
11 05 00 AC FF 00 CRC

The forcing of a coil via Modbus function 5 will be accomplished regardless of whether
the addressed coil is disabled or not (In ProSoft products, the coil is only affected if the
necessary ladder logic is implemented).

Note: The Modbus protocol does not include standard functions for testing or changing the DISABLE state
of discrete inputs or outputs. Where applicable, this may be accomplished via device specific Program
commands (In ProSoft products, this is only accomplished through ladder logic programming).

Coils that are reprogrammed in the controller logic program are not automatically cleared
upon power up. Thus, if such a coil is set ON by function Code 5 and (even months
later), an output is connected to that coil, the output will be "hot".

ProSoft Technology, Inc. Page 122 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.6.8 Preset Single Register (Function Code 06)

Query
Function (06) allows the user to modify the contents of a holding register. Any holding
register that exists within the controller can have its contents changed by this message.
However, because the controller is actively scanning, it also can alter the content of any
holding register at any time. The values are provided in binary up to the maximum
capacity of the controller unused high order bits must be set to zero. When used with
server address zero (Broadcast mode) all server controllers will load the specified
register with the contents specified.

Note Functions 5, 6, 15, and 16 are the only messages that will be recognized as valid for broadcast.

Addr Func Data Start Data Start Data #of Regs Data #of Regs Error Check
Reg Hi Reg Lo Hi Lo Field
11 06 00 01 00 03 CRC

Response
The response to a preset single register request is to re-transmit the query message
after the register has been altered.

Addr Func Data Reg Data Reg Data Input Reg Data Input Reg Error Check Field
Hi Lo Hi Lo
11 06 00 01 00 03 CRC

ProSoft Technology, Inc. Page 123 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.6.9 Diagnostics (Function Code 08)

Modbus function code 08 provides a series of tests for checking the communication
system between a Client device and a server, or for checking various internal error
conditions within a server.
The function uses a two-byte sub-function code field in the query to define the type of
test to be performed. The server echoes both the function code and sub-function code in
a normal response. Some of the diagnostics cause data to be returned from the remote
device in the data field of a normal response.
In general, issuing a diagnostic function to a remote device does not affect the running of
the user program in the remote device. Device memory bit and register data addresses
are not accessed by the diagnostics. However, certain functions can optionally reset
error counters in some remote devices.
A server device can, however, be forced into 'Listen Only Mode' in which it will monitor
the messages on the communications system but not respond to them. This can affect
the outcome of your application program if it depends upon any further exchange of data
with the remote device. Generally, the mode is forced to remove a malfunctioning
remote device from the communications system.

Sub-function Codes Supported

Only Sub-function 00 is supported by the MVI56E-MNETR module.

00 Return Query Data

The data passed in the request data field is to be returned (looped back) in the
response. The entire response message should be identical to the request.

Sub-function Data Field (Request) Data Field (Response)

00 00 Any Echo Request Data

Example and State Diagram

Here is an example of a request to remote device to Return Query Data. This uses a
sub-function code of zero (00 00 hex in the two-byte field). The data to be returned is
sent in the two-byte data field (A5 37 hex).

Request Response
Field Name (Hex) Field Name (Hex)
Function 08 Function 08
Sub-function Hi 00 Sub-function Hi 00
Sub-function Lo 00 Sub-function Lo 00
Data Hi A5 Data Hi A5
Data Lo 37 Data Lo 27

ProSoft Technology, Inc. Page 124 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

The data fields in responses to other kinds of queries could contain error counts or other
data requested by the sub-function code.

ProSoft Technology, Inc. Page 125 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.6.10 Force Multiple Coils (Function Code 15)

Query
This message forces each coil in a consecutive block of coils to a desired ON or OFF
state. Any coil that exists within the controller can be forced to either state (ON or OFF).
However, because the controller is actively scanning, unless the coils are disabled, the
controller can also alter the state of the coil. Coils are numbered from zero (coil 00001 =
zero, coil 00002 = one, and so on). The desired status of each coil is packed in the data
field, one bit for each coil (1= ON, 0= OFF). The use of server address 0 (Broadcast
Mode) will force all attached servers to modify the desired coils.

Note: Functions 5, 6, 15, and 16 are the only messages (other than Loopback Diagnostic Test) that will be
recognized as valid for broadcast.

The following example forces 10 coils starting at address 20 (13 HEX). The two data
fields, CD =1100 and 00 = 0000 000, indicate that coils 27, 26, 23, 22, and 20 are to be
forced on.

Addr Func Hi Add Lo Quantity Byte Data Coil Data Coil Error Check
Add Cnt Status 20 to Status 28 to Field
27 29
11 0F 00 13 00 0A 02 CD 00 CRC

Response
The normal response will be an echo of the server address, function code, starting
address, and quantity of coils forced.

Addr Func Hi Addr Lo Addr Quantity Error Check Field

11 0F 00 13 00 0A CRC

The writing of coils via Modbus function 15 will be accomplished regardless of whether
the addressed coils are disabled or not.
Coils that are unprogrammed in the controller logic program are not automatically
cleared upon power up. Thus, if such a coil is set ON by function code 15 and (even
months later) an output is connected to that coil, the output will be hot.

ProSoft Technology, Inc. Page 126 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.6.11 Preset Multiple Registers (Function Code 16)

Query
Holding registers existing within the controller can have their contents changed by this
message (a maximum of 60 registers). However, because the controller is actively
scanning, it also can alter the content of any holding register at any time. The values are
provided in binary up to the maximum capacity of the controller (16-bit for the 184/384
and 584); unused high order bits must be set to zero.

Note: Function codes 5, 6, 15, and 16 are the only messages that will be recognized as valid for broadcast.

Addr Func Hi Lo Add Quantity Byte Hi Lo Hi Lo Error Check

Add Cnt Data Data Data Data Field
11 10 00 87 00 02 04 00 0A 01 02 CRC

Response
The normal response to a function 16 query is to echo the address, function code,
starting address and number of registers to be loaded.

Addr Func Hi Addr Lo Addr Quantity Error Check Field

11 10 00 87 00 02 56

ProSoft Technology, Inc. Page 127 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.6.12 Modbus Exception Responses

When a Modbus Client sends a request to a server device, it expects a normal
response. One of four possible events can occur from the Client's query:
• If the server device receives the request without a communication error, and can
handle the query normally, it returns a normal response.
• If the server does not receive the request due to a communication error, no response
is returned. The Client program will eventually process a timeout condition for the
request.
• If the server receives the request, but detects a communication error (parity, LRC,
CRC, ...), no response is returned. The Client program will eventually process a
timeout condition for the request.
• If the server receives the request without a communication error, but cannot handle it
(for example, if the request is to read a non-existent output or register), the server
will return an exception response informing the Client of the nature of the error.
The exception response message has two fields that differentiate it from a normal
response:
Function Code Field: In a normal response, the server echoes the function code of the
original request in the function code field of the response. All function codes have a
most-significant bit (MSB) of 0 (their values are all below 80 hexadecimal). In an
exception response, the server sets the MSB of the function code to 1. This makes the
function code value in an exception response exactly 80 hexadecimal higher than the
value would be for a normal response.
With the function code's MSB set, the Client's application program can recognize the
exception response and can examine the data field for the exception code.
Data Field: In a normal response, the server may return data or statistics in the data
field (any information that was requested in the request). In an exception response, the
server returns an exception code in the data field. This defines the server condition that
caused the exception.
The following table shows an example of a Client request and server exception
response.
Request Response
Field Name (Hex) Field Name (Hex)
Function 01 Function 81
Starting Address Hi 04 Exception Code 02
Starting Address Lo A1
Quantity of Outputs Hi 00
Quantity of Outputs Lo 01

In this example, the Client addresses a request to server device. The function code (01)
is for a Read Output Status operation. It requests the status of the output at address
1245 (04A1 hex). Note that only that one output is to be read, as specified by the
number of outputs field (0001).
If the output address is non-existent in the server device, the server will return the
exception response with the exception code shown (02). This specifies an illegal data
address for the server.

ProSoft Technology, Inc. Page 128 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

Modbus Exception Codes

Code Name Meaning
01 Illegal Function The function code received in the query is not an allowable
action for the server. This may be because the function
code is only applicable to newer devices, and was not
implemented in the unit selected. It could also indicate that
the server is in the wrong state to process a request of this
type, for example because it is unconfigured and is being
asked to return register values.
02 Illegal Data Address The data address received in the query is not an allowable
address for the server. More specifically, the combination
of reference number and transfer length is invalid. For a
controller with 100 registers, a request with offset 96 and
length 4 would succeed; a request with offset 96 and length
5 will generate exception 02.
03 Illegal Data Value A value contained in the query data field is not an allowable
value for server. This indicates a fault in the structure of the
remainder of a complex request, such as that the implied
length is incorrect. It specifically does not mean that a data
item submitted for storage in a register has a value outside
the expectation of the application program, because the
Modbus protocol is unaware of the significance of any
particular value of any particular register.
04 Slave Device Failure An unrecoverable error occurred while the server was
attempting to perform the requested action.
05 Acknowledge Specialized use in conjunction with programming
commands. The server has accepted the request and is
processing it, but a long duration of time will be required to
do so. This response is returned to prevent a timeout error
from occurring in the Client. The Client can next issue a
poll program complete message to determine if processing
is completed.
06 Slave Device Busy Specialized use in conjunction with programming
commands. The server is engaged in processing a long-
duration program command. The Client should retransmit
the message later when the server is free.
08 Memory Parity Error Specialized use in conjunction with function codes 20 and
21 and reference type 6, to indicate that the extended file
area failed to pass a consistency check. The server
attempted to read record file, but detected a parity error in
the memory. The Client can retry the request, but service
may be required on the server device.
0a Gateway Path Unavailable Specialized use in conjunction with gateways, indicates
that the gateway was unable to allocate an internal
communication path from the input port to the output port
for processing the request. Usually means that the gateway
is misconfigured or overloaded.
0b Gateway Target Device Specialized use in conjunction with gateways, indicates
Failed To Respond that no response was obtained from the target device.
Usually means that the device is not present on the
network.

ProSoft Technology, Inc. Page 129 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.7 Using the Optional Add-On Instruction Rung Import

5.7.1 Before You Begin

• Make sure that you have installed RSLogix 5000 version 16 (or later).
• Download the Optional Add-On file MVI56EMNETR_Optional_Rung_vXXX.L5X from
www.prosoft-technology.com.
• Save a copy in a folder in your PC.

5.7.2 Overview
The Optional Add-On Instruction Rung Import contains optional logic for MVI56E-
MNETR applications to perform the following tasks.
• Read/Write Ethernet Configuration
Allows the processor to read or write the module IP address, netmask and gateway
values.

Note: This is an optional feature. You can perform the same task through PCB (ProSoft Configuration
Builder). Even if your PC is in a different network group you can still access the module through PCB by
setting a temporary IP address.

• Read/Write Module Clock Value

Allows the processor to read and write the module clock settings. The module clock
stores the last time that the Ethernet configuration was changed. The date and time
of the last Ethernet configuration change is displayed in the scrolling LED during
module power up.

Important: The Optional Add-On Instruction only supports the two features listed above. You must use the
sample ladder logic for all other features including backplane transfer of Modbus TCP/IP data.

ProSoft Technology, Inc. Page 130 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.7.3 Installing the Rung Import with Optional Add-On Instruction

1 Right-click an empty rung in the main routine of your existing ladder logic and choose
IMPORT RUNG.

2 Navigate to the folder where you saved MVI56EMNETR_Optional_Rung_v1_1.L5X

and select the file.

ProSoft Technology, Inc. Page 131 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

3 In the IMPORT CONFIGURATION window, click OK.

The Add-On Instruction will be now visible in the ladder logic. Observe that the
procedure has also imported data types and controller tags associated to the Add-On
Instruction.

ProSoft Technology, Inc. Page 132 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

You will notice that new tags have been imported: four MESSAGE tags,
MVI56MNETRCLOCK and MVI56MNETRETHERNET tags.

4 In the Add-On Instruction, click the [...] button next to each MSG tag to open the
MESSAGE CONFIGURATION TAG.
5 Click the COMMUNICATION tab and click the BROWSE button as follows.

ProSoft Technology, Inc. Page 133 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

6 Select the module to configure the message path.

ProSoft Technology, Inc. Page 134 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.7.4 Reading the Ethernet Settings from the Module

1 Expand the MVI56MNETRETHERNET controller tag and move a value of 1 to
MVI56MNETRETHERNET.READ.

2 The bit will be automatically reset and the current Ethernet settings will be copied
to MVI56MNETRETHERNET controller tag as follows.

3 To check the status of the message, refer to the READETHERNETMSG tag.

ProSoft Technology, Inc. Page 135 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.7.5 Writing the Ethernet Settings to the Module

1 Expand the MVI56EMNETRETHERNET controller tag.
2 Set the new Ethernet configuration in MVI56EMNETRETHERNET.CONFIG
3 Move a value of 1 to MVI56MNETRETHERNET.WRITE

4 After the message is executed, the MVI56MNETRETHERNET.WRITE bit resets to

0.

5 To check the status of the message, refer to the WRITEETHERNETMSG tag.

ProSoft Technology, Inc. Page 136 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.7.6 Reading the Clock Value from the Module

1 Expand the MVI56MNETRCLOCK controller tag and move a value of 1 to
MVI56MNETRCLOCK.READ

2 The bit will be automatically reset and the current clock value will be copied to
MVI56MNETRCLOCK.CONFIG controller tag as follows.

3 To check the status of the message, refer to the READCLOCKMSG tag.

ProSoft Technology, Inc. Page 137 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.7.7 Writing the Clock Value to the Module

1 Expand the MVI56MNETRCLOCK controller tag.
2 Set the new Clock value in MVI56MNETRCLOCK.CONFIG
3 Move a value of 1 to MVI56MNETRCLOCK.WRITE

4 The bit will be automatically reset to 0.

5 To check the status of the message, refer to the WRITECLOCKMSG tag.

ProSoft Technology, Inc. Page 138 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.8 Adding the Module to an Existing Project

1 Add the MVI56E-MNETR module to the project. Select the I/O CONFIGURATION
folder in the Controller Organization window, and then click the right mouse button to
open a shortcut menu. On the shortcut menu, choose NEW MODULE.

This action opens the Select Module dialog box:

ProSoft Technology, Inc. Page 139 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

2 Select the 1756-MODULE (Generic 1756 Module) from the list and click OK. This
action opens the New Module dialog box.

Parameter Value
Name Enter a module identification string. The recommended value is
MNETR.
Description Enter a description for the module. Example: MODBUS TCP/IP
INTERFACE MODULE WITH REDUCED DATA BLOCK.
Comm Format Select DATA-INT (Very Important)
Slot Enter the slot number in the rack where the MVI56E-MNETR
module will be installed.
Input Assembly Instance 1
Input Size 42
Output Assembly Instance 2
Output Size 42
Configuration Assembly Instance 4
Configuration Size 0

Enter the Name, Description and Slot options for your application. You must select
the COMM FORMAT AS DATA - INT in the dialog box, otherwise the module will not
communicate over the backplane of the ControlLogix rack. Click OK to continue.

ProSoft Technology, Inc. Page 140 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

3 In the Connection tab of the Module Properties dialog, select the Requested Packet
Interval value for scanning the I/O on the module. This value represents the
minimum frequency that the module will handle scheduled events. This value should
not be set to less than 1 millisecond. The default value is 5 milliseconds. Values
between 1 and 10 milliseconds should work with most applications.

4 Save the module and click OK to dismiss the dialog box. The Controller Organization
window now displays the module's presence.

5 Copy the Controller Tags (page 66) from the sample program.
6 Copy the User Defined Data Types (page 68) from the sample program.
7 Copy the Ladder Rungs from the sample program.
8 Save and Download (page 30, page 146) the new application to the controller and
place the processor in run mode.

ProSoft Technology, Inc. Page 141 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.9 Using the Sample Program

If your processor uses RSLogix 5000 version 15 or earlier, you will not be able to use the
Add-On Instruction for your module. Follow the steps below to obtain and use a sample
program for your application.

5.9.1 Opening the Sample Program in RSLogix

The sample program for your MVI56E-MNETR module includes custom tags, data types
and ladder logic for data I/O, status and command control. For most applications, you
can run the sample program without modification, or, for advanced applications, you can
incorporate the sample program into your existing application.

Download the manuals and sample program from the ProSoft Technology web site
You can always download the latest version of the sample ladder logic and user
manuals for the MVI56E-MNETR module from the ProSoft Technology website, at
www.prosoft-technology.com/support/downloads (http://www.prosoft-
technology.com/support/downloads)
From that link, navigate to the download page for your module and choose the sample
program to download for your version of RSLogix 5000 and your processor.

To determine the firmware version of your processor

Important: The RSLinx service must be installed and running on your computer in order for RSLogix to
communicate with the processor. Refer to your RSLinx and RSLogix documentation for help configuring and
troubleshooting these applications.

1 Connect an RS-232 serial cable from the COM (serial) port on your PC to the
communication port on the front of the processor.
2 Start RSLogix 5000 and close any existing project that may be loaded.
3 Open the COMMUNICATIONS menu and choose GO ONLINE. RSLogix will establish
communication with the processor. This may take a few moments.

ProSoft Technology, Inc. Page 142 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

4 When RSLogix has established communication with the processor, the Connected
To Go Online dialog box will open.

5 In the Connected To Go Online dialog box, click the GENERAL tab. This tab shows
information about the processor, including the Revision (firmware) version. In the
following illustration, the firmware version is 11.32

6 Select the sample ladder logic file for your firmware version.

To open the sample program

1 On the Connected to Go Online dialog box, click the SELECT FILE button.
2 Choose the sample program file that matches your firmware version, and then click
the SELECT button.
3 RSLogix will load the sample program.
The next step is to configure the correct controller type and slot number for your
application.

ProSoft Technology, Inc. Page 143 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.9.2 Choosing the Controller Type

The sample application is for a 1756-L63 ControlLogix 5563 Controller. If you are using
a different model of the ControlLogix processor, you must configure the sample program
to use the correct processor model.
1 In the Controller Organization list, select the folder for the controller and then click
the right mouse button to open a shortcut menu.
2 On the shortcut menu, choose PROPERTIES. This action opens the Controller
Properties dialog box.

3 Click the CHANGE TYPE or CHANGE CONTROLLER button. This action opens the
Change Controller dialog box.

4 Open the TYPE dropdown list, and then select your ControlLogix controller.
5 Select the correct firmware revision for your controller, if necessary.
6 Click OK to save your changes and return to the previous window.

ProSoft Technology, Inc. Page 144 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.9.3 Selecting the Slot Number for the Module

The sample application is for a module installed in Slot 1 in a ControlLogix rack. The
ladder logic uses the slot number to identify the module. If you are installing the module
in a different slot, you must update the ladder logic so that program tags and variables
are correct, and do not conflict with other modules in the rack.

To change the slot number

1 In the Controller Organization list, select the module, and then click the right mouse
button to open a shortcut menu.
2 On the shortcut menu, choose PROPERTIES. This action opens the Module Properties
dialog box.

3 In the SLOT field, use the up and down arrows on the right side of the field to select
the slot number where the module will reside in the rack, and then click OK.
RSLogix will automatically apply the slot number change to all tags, variables and ladder
logic rungs that use the MVI56E-MNETR slot number for computation.

ProSoft Technology, Inc. Page 145 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Reference
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

5.9.4 Downloading the Sample Program to the Processor

Note: The key switch on the front of the ControlLogix processor must be in the REM position.

1 If you are not already online to the processor, open the COMMUNICATIONS menu, and
then choose DOWNLOAD. RSLogix will establish communication with the processor.
2 When communication is established, RSLogix will open a confirmation dialog box.
Click the DOWNLOAD button to transfer the sample program to the processor.

3 RSLogix will compile the program and transfer it to the processor. This process may
take a few minutes.
4 When the download is complete, RSLogix will open another confirmation dialog box.
Click OK to switch the processor from PROGRAM mode to RUN mode.

Note: If you receive an error message during these steps, refer to your RSLogix documentation to interpret
and correct the error.

5.9.5 Adding the Sample Ladder to an Existing Application

1 Copy the Controller Tags (page 66) from the sample program.
2 Copy the User-Defined Data Types (page 68) from the sample program.
3 Copy the Ladder Rungs from the sample program.
4 Save and Download (page 30, page 146) the new application to the controller and
place the processor in RUN mode.

ProSoft Technology, Inc. Page 146 of 147

MVI56E-MNETR ♦ ControlLogix™ Platform Support, Service & Warranty
Modbus TCP/IP Interface Module with Reduced Data Block User Manual

6 Support, Service & Warranty

6.1 Contacting Technical Support

ProSoft Technology, Inc. is committed to providing the most efficient and effective
support possible. Before calling, please gather the following information to assist in
expediting this process:
1 Product Version Number
2 System architecture
3 Network details

If the issue is hardware related, we will also need information regarding:

1 Module configuration and associated ladder files, if any
2 Module operation and any unusual behavior
3 Configuration/Debug status information
4 LED patterns
5 Details about the serial, Ethernet or Fieldbus devices interfaced to the module, if any.

Note: For technical support calls within the United States, ProSoft Technology’s 24/7 after-hours phone
support is available for urgent plant-down issues.

North America (Corporate Location) Europe / Middle East / Africa Regional Office
Phone: +1.661.716.5100 Phone: +33.(0)5.34.36.87.20
[email protected] [email protected]
Languages spoken: English, Spanish Languages spoken: French, English
REGIONAL TECH SUPPORT REGIONAL TECH SUPPORT
[email protected] [email protected]
Latin America Regional Office Asia Pacific Regional Office
Phone: +52.222.264.1814 Phone: +60.3.2247.1898
[email protected] [email protected]
Languages spoken: Spanish, English Languages spoken: Bahasa, Chinese, English,
REGIONAL TECH SUPPORT Japanese, Korean
[email protected] REGIONAL TECH SUPPORT
[email protected]

6.2 Warranty Information

For complete details regarding ProSoft Technology’s TERMS & CONDITIONS OF
SALE, WARRANTY, SUPPORT, SERVICE AND RETURN MATERIAL
AUTHORIZATION INSTRUCTIONS, go to www.prosoft-technology.com/legal

Documentation is subject to change without notice.

ProSoft Technology, Inc. Page 147 of 147