abcd
Responsible department: Take over department:
ALSTOM Power
Revision: Doc. type:
HTGD662216
File no.:
TSNDSH
Prepared: Checked:
C
Approved:
C
2006-12-21 mkoller
Replaces:
HTGD SA04E-01-041
Language: Page:
2006-12-21 M. Meier
Valid for:
2006-12-21 mkoller
Derived from:
en
Data set:
1/8
System Instruction
Eddy current proximity transducer system
Bently Nevada 3300XL 11mm Table of Contents 1 2 3 4
2006-12-21 EN Approved
Lng. Status
PURPOSE .................................................................................................................................. 1 DESIGN OF SUPPLIER.............................................................................................................. 2 ADDITIONAL TECHNICAL DATA ............................................................................................... 4 QUALTITY REQUIREMENTS..................................................................................................... 6 ELECTRICAL CONNECTION PRINCIPLE ................................................................................. 6 SCOPE OF APPLICATION ......................................................................................................... 7 SUPPLIER DATA........................................................................................................................ 8
5 6 7
Rev. Released
Type
PURPOSE
9665 HTGD662216
Dept. Document No.
This design instruction compiles the technical data of the Bently Nevada Type 3300 XL 11mm proximity transducer system. The system provides an output voltage directly proportional to the distance between the probe tip and the observed conductive surface. It is capable of both static ( position ) and dynamic ( vibration ) measurement, and is primarly used for vibration and position measurement applications on fluid-film bearing machines.The system contents :
We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third parties without express authority is strictly forbidden. ALSTOM 2006
abcd
2
2.1
Revision:
Language:
Page:
en
2/8
HTGD662216
DESIGN OF SUPPLIER
Restrictions For the 3300 XL Proximitor Sensor, extension cable and probe, the specified values are given by +22 C (+72 F) -24 VDC power supply 10 kOhm load AISI 4140 steel target probe gapped at 1.27 mm (50 mils) Performance characteristics are applicable for systems that consist solely of 3300 XL components.
2.2
General Data
Eddy current Probe Manufacturer Manufacturer designation Manufacturer order number xx will be defined in chapter 3 Protection Extension cable Bently Nevada Extension Cable 330730Axxx-Bxx-Cxx Amplifier
2006-12-21 EN Approved
Proximity Probe 3307xx-Axx-BxxCxx-Dxx-Exx
Proximitor Sensor 330780Axx-Bxx
Rev. Released
Lng. Status
- North : - Ex nA IIC T5 Class I Zone 2 America - Ex nA IIC T5 Class I, Division 2, Groups A, B, C, D - Europe :- Ex nA for Zone 2, Group IIC -51 to 177 C -60 to 351 F -35 to 85 C -31 to 185 F
Type
9665 HTGD662216
Dept. Document No.
Ambient temperature range
2.3
Materials
Proximity Probe Polyphenylene sulphide ( PPS ) AISI 303 stainless steel ( SST ) 75 triaxial fluoroethylene propylene ( FEP ) Extension Cable 75 triaxial fluoroethylene propylene ( FEP ) Gold-plated brass Proximitor Sensor A308 aluminium -
Probe tip material Case material Cable
Connector material Gland plate gasket material Cover gasket material
abcd
2.4
Revision:
Language:
Page:
en
3/8
HTGD662216
Measurement data
Type Input Measuring range Input Linear range Output Linear range Incremental Scale Factor ( ISF ) Accuaracy of ISF Eddy current probe with amplifier One noncontacting 3300 XL 11 mm Proximity Probe and Extension Cable 4 mm ( 160 mils ) 0.5 to 4.5 mm ( 20 to 180 mils ) Approximately -1 to 17V DC 3.94 V/mm ( 100 mV/mil) Standard 9m System Probe Extension Cable Deviation from best fit straight line (DSL): Frequency Response Recommended Gap setting Minimum target size Shaft diameter : - recomended min. Target material 10.0% including interchangeability error when measured in increments of 0.5 mm (20 mils) over the 4mm (160 mil) linear range from 0 to 45 C (32 to 110 F).
1m 8m
2006-12-21 EN Approved
Lng. Status
Less than 10m (4 mil) with components at 0 to -45C (32 to-110F). 0 to 8kH; 0 to -3dB up to 305meters ( 1000feed) 2.5 mm ( 100mils ) 30.5mm (1.2 inch) diameter ( flat target ) 152 mm ( 6in) AISI 4140 steel Calibration to other target materials is available upon request
Rev. Released Type
2.5
9665 HTGD662216
Dept. Document No.
Electrical Data
Power supply Supply sensitivity Power consumption Output resistance Probe DC resitance (1m) Extension Cable (8m) From Bently Nevada I/O-Rack -17.5 to 26 VDC less than 2 mV change in output per 1 volt change in power supply max . 12 mA 50 Ohm nominal 5.9 0.50 Ohm center conductor to outer conductor nominal 1.0 0.25 Ohm center conductor to center conductor nominal 0.3 0.10 Ohm outer conductor to outer conductor
abcd
3
3.1
Revision:
Language:
Page:
en
4/8
HTGD662216
ADDITIONAL TECHNICAL DATA
Bently Nevada 3300 XL 11mm Probe
3.1.1 Assembly drawing 330707-AXX-BXX-CXX-DXX-EXX, 330708-AXX-BXX-CXX-DXX-EXX, 330709-AXX-BXX-CXX-DXX-EXX, 330710-AXX-BXX-CXX-DXX-EXX, 5/8-18 UNF-2A without armor 5/8-18 UNF-2A with armor M16 x 1.5 without armor M16 x 1.5 with armor
2006-12-21 EN Approved
Lng. Status
Rev. Released
3.1.2 Bently Product structure and ALSTOM ordering table
Bently Nevada Ordering Information Casing Variant
07 08 09 10 5/8-18 UNF thread, without armor 5/8-18 UNF thread, with armor M16 x 1.5 thread, without armor M16 x 1.5 thread, with armor 0 1 2 3
Type
9665 HTGD662216
Dept. Document No.
Alstom Ordering No HTGD701627P X X X X
A Unthreaded Length B Overall Case Length
07 08 08 09 10 10 00 00 00 00 00 00 20 value multiplied with 0.1 inch 20 value multiplied with 0.1 inch 25 value multiplied with 0.1 inch 50 50 78 0 0 1 2 2 3 1 5 9
C: Total Length Option
10 1.0 metre (3.3 feet) 50 5.0 metre (16.4 feet) 90 9.0 metre (29.5 feet)
D: Connector and Cabel Type
00 Connector not installed, Standard cable 01 Miniature coaxial ClickLocTM connector with connector protector Standard cable 02 Miniature coaxial ClickLocTM connector Standard cable 10 Connector not installed, FluidLoc cable 11 Miniature coaxial ClickLocTM connector with connector protector FluidLoc cable 12 Miniature coaxial ClickLocTM connector FluidLoc cable
E: Agency Approval Option
00 05 Not required Multiple Approvals 0 5
3307
00 -
02 -
abcd
3.2
Revision:
Language:
Page:
en
5/8
HTGD662216
Bently Nevada 3300 11mm XL Extension cable
3.2.1 Assembly drawing 330730-AXX-BXX-CXX
2006-12-21 EN Approved
Lng. Status
3.2.2 Bently Product structure and ALSTOM ordering table The extension cable length shall be choosen in such a way that the total length (probe and extension cable) is 5.0 or 9.0 meter
Bently Nevada Ordering Information A: Total Length Option
040 4.0 metre (13.1 feet) 080 8.0 metre (26.2 feet) 4 8 0 1 2 3 4 5 6 7 0 5
Rev. Released Type
Alstom Ordering No HTGD701627P8 X X X
9665 HTGD662216
Dept. Document No.
B:
Connector and cable option
00 01 02 03 10 11 12 13 Standard cable Armored cable Standard cable with connector protectors Armored cable with connector protectors FluidLoc cable Armored FluidLoc cable FluidLoc cable with connector protectors Armored FluidLoc cable with connector protectors
C:
Agency Approval Option
00 05 Not required Multiple Approvals
330730 -
abcd
3.3
Revision:
Language:
Page:
en
6/8
HTGD662216
Bently Nevada 3300 XL Proximitor Sensor
3.3.1 Assembly drawing 330780-AX0-BXX-CXX panel mount 330780-AX1-BXX-CXX DIN mount
2006-12-21 EN Approved
Lng. Status
Rev. Released
3.3.2 Bently Product structure and ALSTOM ordering table The proximitor sensor shall be choosen based on the total length of the probe and extension cable (5.0 or 9.0 meter).
Bently Nevada Ordering Information Alstom Ordering No HTGD701627P9 XX X
50 51 52 90 91 92 0 5
Type
9665 HTGD662216
Dept. Document No.
A: Total length and Mounting option
50 51 52 90 91 92 5.0 metre (16.4 feet) system length, panel mount 5.0 metre (16.4 feet) system length, DIN mount 5.0 metre (16.4 feet) system length, no mounting hardware 9.0 metre (29.5 feet) system length, panel mount 9.0 metre (29.5 feet) system length, DIN mount 9.0 metre (29.5 feet) system length, no mounting hardware
B: Agency Approval Option
00 05 Not required Multiple approvals
330780
QUALTITY REQUIREMENTS
Probe final test result: Calibration and test record from supplier of the probe
ELECTRICAL CONNECTION PRINCIPLE
abcd
6
6.1
Revision:
Language:
Page:
en
7/8
HTGD662216
SCOPE OF APPLICATION
Used for FAST-Platform
Note : In the table there is the allocation of the eddy current proximity system to the product platform bearing pedestals which are defined before issue date of this document.
6.1.1 For power train with air cooled generators
HTGD701627
THRUST POSITION
MEASURING POINT
Description of Mesuring Points FBnx : Front bearing pedestal TBnx : Thrust bearing pedestal nnSx : Standard nnCx : with Clutch nnGx : for Generator nnOx : with Oil pump nnn1 : Size 1 nnn2 : Size 2 nnn3 : Size 3
2006-12-21 EN Approved
TB S
1
Lng. Status
Probe :
P2210
BENTLY. No 330709-00-25-10-02-00 Extension cable : X 1
Rev. Released
P8800
BENTLY. No 330730-80-00-00 Sensor : X 1
Type
9665 HTGD662216
P9910
BENTLY. No 330780-91-00
Dept. Document No.
6.1.2 For power train with H2 cooled generators
HTGD701627
THRUST POSITION
MEASURING POINT
Description of Mesuring Points FBnx : Front bearing pedestal TBnx : Thrust bearing pedestal nnSx : Standard nnCx : with Clutch nnGx : for Generator nnOx : with Oil pump nnn1 : Size 1 nnn2 : Size 2 nnn3 : Size 3
TB S O C
1
Probe :
P2215
BENTLY. No 330709-00-25-10-02-05 Extension cable : X 1
P8805
BENTLY. No 330730-80-00-05 Sensor : X 1
P9915
BENTLY. No 330780-91-05
abcd
7
Revision:
Language:
Page:
en
8/8
HTGD662216
SUPPLIER DATA
Bently Nevada GmbH Martin-Behaim Strasse 10 D-63263 Neu-Isenburg Federal Republic of Germany Mailing address: P.O. Box 1150 D-63231 Neu-Isenburg Federal Republic of Germany Phone: +49.6102.73960 Fax: +49.6102.31258
Rev. Released Type Dept. Document No.
9665 HTGD662216
2006-12-21 EN Approved
Lng. Status
