982

6.5.8.2.1 The provisions of this section may be used as alternative to those of

Sections 6.5.1 to 6.5.7 for two-way slabs supported on all four edges by walls, steel
beams or monolithic concrete beams having a total depth not less than 3 times the
slab thickness.
6.5.8.2.2 Pancls shall be rectangular with a longer to shorter centre to centre
support span ratio of not grcater than 2.

6.5.8.2.3 The value of ("2) shallbe greater than or equal to 1.

6.5.8.3 Analysis by the Coefficient Method
6.5.8.3.1 The negative monents and dead load and live load positive moments in
the two directions shall be computed from Tables 6.6.8, 6.6.9 and 6.6.10
respectively. Shear in the slab and loads on the supporting beams shall be computed
from Table 6.6.11.
Table 6.6.8: Coefficients for Negative Moments in Slabs T

Maneg = CanegWla
Mbneg =C bnegWlý
Where, w=total uniform dead plus live load per unit area

Case 1 Case 2 Case 3 Case 4 Case 5 Case 6 Case 7 Case Case 9

Span Moment
Ratio, Coefficient
la
m=

0.045 0.050 0.075 0.071 0.033 0.061

1.00
Caneg
0.045 0.076 0.050 0.071 0.061 0.033
Chneg
0.050 0.055 0.079 0.075 0.038 0.065
0.95
Caneg
0.041 0.072 0.045 0.067 0.056 0.029
Chneg
0.055 0.060 0.080 0.079 0.043 0.068
Caneg
0.90
Chneg 0.037 0.070 0.040 0.062 0.052 0.025
0.060 0.066 0.082 0.083 0.049 0.072
0.85
Caneg
0.031 0.065 0.034 0.057 0.046 0.021
Cbneg
0.065 0.071 0.083 0.086 0.055 0.075
Caneg
0.80
Ch,neg 0.027 0.061 0.029 0.051 0.041 0.017
 9289

Span Moment Case I Case 2 Case Case 4 Case 5 Case 6 Case 7 Case 8 Case 9
Ratio, Coefficient
la
m

0.75 Caneg 0.069 0.076 0.085 0.088 0.061 0.078

Coneg 0.022 0.056 0.024 0.044 0.036 0.014

0.70 Caneg 0.074 0.081 0.086 0.091 0.068 0.081

Cbneg 0.017 0.050 0.019 0.038 0.029 0.011

0.65 Caneg 0.077 0.085 0.087 0.093 0.074 0.083

Cbneg 0.014 0.043 0.015 0.031 0.024 0.008

0.60 Caneg 0.081 0.089 0.088 0.095 0.080 0.085

Cbneg 0.010 0.035 0.011 0.024 0.018 0.006

0.55 Caneg 0.084 0.092 0.089 0.096 0.085 0.086

Cb,neg 0.007 0.028 0.008 0.019 0.014 0.005

Caneg 0.086 0.094 0.090 0.097 0.089 0.088

0.50
Coneg 0.006 0.022 0.006
0.014 0.010 0.003
tA crosshatched edge indicates that the slab continues across, or is fxed at the
support; an unmarked edge indicates a support at which torsional resistance is
negligible.
Table 6.6.9: Coefficients for Dead Load Positive Moments in Slabs T
M
apos,dl = Caawl
Mb,pos,d! =Cb,aiwl;
Where, w = uniform dead load per unit area
Span Moment Case 1 Case 2 Case 3 Case 4 Case S Case 6 Case 7 Case 8 Case 9
Ralio, Coefficient

m=

Cadl 0.036 0.018 0.018 0.027 0.027 0.033 0.027 0.020 0.023
1.00
Chdl 0.036 0.018 0.027 0.027 0.018 0.027 0.033 0.023 0.020
988

Span Moment Case 1 Case Case 4 Case 5 Case 6 Case 7 Case 8 Case 9
Ratio, Coefficient

la

D
m=

0.040 0.020 0.021 0.030 0.028 0.036 0.031 0.022 0.024

Ga,di
0.95
0.033 0.016 0.025 0.024 0.0150.024 0.031 0.021 0.017

Ga,dl 0.045 0.022 0.025 0.033 0.029 0.039 0.035 0.025 0.026
0.90
Ch,dl 0.029 0.014 0.024 0.022 0.013 0.021 0.028 0.019 0.015

Ga,dl 0.050 0.024 0.029 0.036 0.031 0.042 0.040 0.029 0.028
0.85
Cb,dl 0.026 0.012 0.022 0.019 0.011 0.017 0.025 0.017 0.013

Ca.dl 0.056 0.026 0.034 0.039 0.032 0.045 0.045 0.032 0.029
0.80
0.023 0.011 0.020 0.016 0.009 0.015 0.022 0.015 0010

Cadt 0.061 0.028 0.040 0.043 0.033 0.048 0.051 0.036 0.031
0.75
0.019 0.009 0.018 0.013 0.007 0.012 0.020 0.013 0.007
Chai
0.068 0.030 0.046 0.046 0.035 0.051 0.058 0.040 0.033
Cadl
0.70
0.016 0.007 0.016 0.011 0.005 0.009 0.017 0.011 0.006

0.074 0.032 0.054 0.050 0.036 0.054 0.065 0.044 0.034

Ca,di
0.65
0.013 0.006 0.014 0.009 0.004 0.007 0.014 0.009 0.005
Ch,ai
0.081 0.034 0.062 0.053 0.037 0.056 0.073 0.048 0.036
0.60
Ca,dl
0.010 0.004 0.011 0.007 0.003 0.006 0.012 0.007 0.004
Ch,dl
0.088 0.035 0.071 0.056 0.038 0.058 0.081 0.052 0.037
0.55
Cadl
0.008 0.003 0.009 0.005 0.002 0.004 0.009 0.005 0.003
Chdl
0.095 0.037 0.080 0.059 0.039 0.061 0.089 0.056 0.038
0.50
Cadl
0.006 0.002 0.007 0.004 0.001 0.003 0.007 0.004 0.002
Chdl
tAerosshatched edge indicates that the slab continues across, or is fixed at the
support; an unmnarked edge indicates a support at which torsional resistance is
negligible.
 9280

Table 6.6.10: Coefficients for Live Load Positive Moments in Slabs t

Mapos Cawla
Mb.posll = Chawl; Wherc, w = uniform live load per unit arca
Span Momet Case | Case ? Case 3 CAse 4 Case 5 Case 6 Case 7 Case 8 Case 9
Ratio, Cocfficent

m=

Chll 0.036
1.00 0.027|0.0270.0320.0320.0350.032 0,028 0.030
Coll 0.036 0.0270.032 |0.0320.027
|0.0320.0350.0300.028
ba,ll 0.040 0.0300.0310.0350.0340.0380.036|0.031 0.032
0.95
Cbl 0.033 0.0250.0290.0290.0240.0290.0320.027 |0.025

0.90 Call 0.0450.034|0.0350.039 0.037 0.042 0.0400.0350.036

Coll 0.029 0.0220.027 0.026|0.0210.0250.0290.0240.022

0.85 Call 0.0500.037|0.040 0.0430.0410.046|0.045 0.0400.039

Chl0.026 0.0190.024|0.023 0.0190.022 |0.026|0.022|0.020
Call 0.056 |0.0410.0450.0480.044 0.0510.051|0.0440.042
0.80
Coll 0.0230.0170.022 0.0200.016|0.0190.0230.0190.017
Ca,l 0.061 0.0450.0510.052 0.0470.0550.0560.0490.046
0.75
Cpll 0.019 0.014|0.019 0.0160.013
0.016|0.020|0.0160.013
0.70 Cal 0.0680.0490.0570.0570.0510.060 0.0630.054 0.050
0.016
0.012|0.016|0.014|0.011 |0.0130.0170.014 0.011
0,65 Ca,l 0.074
0.053|0.0640.0620.055 0.064 0.070 0.0590.054
Cb 0.013 0.0100.014|0.011 |0.0090.0100.0140.011 0.009
0.60 Call 0.081 0.0580.071 0.0670.059 0.0680.077|0.0650.059
Coll 0.010 0.007|0.0110.0090.0070.0080.0110.009 0.007
0.55 Call 0.0880.062|0.0800.0720.063 0.073 0.0850.070 00.063
Coll 0.0080.006|0.009 0.0070.0050.0060.0090.0070.006
Call 0.095 0.0660.0880.077|0.067 |0.0780.092|0.076|0.067
0.50
Chl0.006 |0.004 0.007|0.0050.004 0.005 0.007|0.0050.004
t Acrosshatched edge indicates that the slab continues
across, or is fixed at the
support; an unmarked edge indicates a support at which torsional resistance is
negligible,
983

Table 6.6.11: Ratio of Total Load win la and h Directions (Wa and W) for
Shear in Slab and Load on Supports
Span Load Case 1 Case 2 \Case 3 Case 4Case 5Case 6Case 7 Case 8 Case 9
Ratio, Ratio
la
m=

0.50 0.83 0.71 0.29 0.33 0.67

W 0.50 0.50 0.17
1.00 0.71 0.67 0.33
0.50 0.50 0.83 0.50 0.17 0.29
Wh 0.38 0.71
0.55 0.55 0.20 0.55 0.86 0.75 0.33
0.95
W.
0.45 0.14 0.25 0.67 0.62 0.29
0.45 0.45 0.80
W
0.60 0.88 0.79 0.38 0.43 0.75
0.60 0.60 0.23
0.90
Wa
0.40 0.77 0.40 0.12 0.21 0.62 0.57 0.25
0.40
W) 0.79
0.66 0.28 0.66 0.90 0.83 0.43 0.49
W, 0.66
0.85 0.10 0.17 0.57 0.51 0.21
W, 0.34 0.34 0.72 0.34
0.71 0.92 0.86 0.49 0.55 0.83
W 0.71 0.71 0.33
0.80 0.08 0.14 0.51 0.45 0.17
0.29 0.29 0.67 0.29
W,
0.39 0.76 0.94 0.88 0.56 0.61 0.86
W, 0.76 0.76
0.75 0.24 0.61 0.24 0.06 0.12 0.44 0.39 0.14
W; 0.24
0.45 0.81 0.95 0.91 0.62 0.68 0.89
0.81 0.81
0.70
Wa
0.19 0.19 0.55 0.19 0.05 0.09 0.38 0.32 0.11
W,
0.85 0.53 0.85 0.96 0.93 0.69 0.74 0.92
W, 0.85
0.65 0.07 0.31 0.26 0.08
0.15 0.15 0.47 0.15 0.04
W,
0.89 0.89 0.61 0.89 0.97 0.95 0,76 0.80 0.94
Wa
0.60 0.11 0.03 0.05 0.24 0.20 0.06
W, 0.11 0.11 0.39
0.92 0.69 0.92 0.98 0.96 0.81 0.85 0.95
0.92
0.55 Wa 0.04 0.19 0.15 0.05
0.08 0.08 0.31 0.08 0.02
W, 0.89 0.97
0.94 0.94 0.76 0.94 0.99 0.97 0.86
W,
0.50 0.03 0.14 0.11 0.03
Wb 0.06 0.06 0.24 0.06 0.01
fixed at the
t Acrosshatched edge indicates that the slab continues across, or is
support at which torsional resistance is
support; an unmarked edge indicates a
negligible.