Brush/Hedge Brush 5 Crisscross layers of 15 dormant

Layering Step-by-Step cuttings per foot or 10 rooted cuttings

per foot. Deposit topsoil over cuttings
Top of Bank
and water liberally.
Compress soil to
1 2 - 4 inches.

River

Bank
Plan View
Ordinary High Water Willow
River 3/4
River Bottom buried
Gravel
River Bottom
2 Top of Bank
6 Wrap second layer of soil/topsoil mix with
Construct during periods ENC2 and CF7 coir fabrics (or equivalent)
of dry river bed or 2' - 3' over topsoil and stake fabric into place.
isolate work area. Water each layer liberally and compress
soil/topsoil mix to 12" - 14" before willow
Excavated placement.
Bank
Soil
/To
psoi
River Bottom l
Gravel
River Bottom
3
Top of Bank 7 Repeat steps 4, 5, 6 until desired bank
Wrap gravel with ENC2 height is reached.
and CF7 (or the equivalent)
biodegradable coir fabric.
Install vegetative
Clean 12" mat (native species)
Gravel -14
"
12" Compressed
-14
2'-3' " Soil/Topsoil
Gravel Mix
River Bottom Coir fabric wrap
River Bottom

8 Trim vegetative mat shoots by 1/3 to

Top of Bank compensate for root loss and promote
4 root growth.
Trim willow so
1/4 of total
Anchor coir fabric with cutting length Vegetative Mat
wooden stakes. is above
ground.
OHW
Clean Gravel
Gravel
River Bottom Coir fabric wrap Secure toe of slope and
Earth
Anchor provide habitat for fish.
Brush/Hedge Brush Layering

Brush layering is a revegetation technique, which combines layers of dormant or

rooted cuttings (see Dormant Cuttings under Care and Preparation of Plant
Material section) with soil to revegetate and stabilize both streambanks and
slopes. A larger variety of plant species may be utilized with a hedge brush
layer (dormant cuttings and rooted plants) than with a simple brush layer
(dormant cuttings). Rooted plants of species that do not root readily, such as
alder, Scouler and Bebb Willow, can be included in the plant layer. A mixture of
species may allow the revegetation project to blend with existing vegetation.
Branches are placed on an angled bench that follows the contour of the slope and
provides reinforcement to the soil. Steep slopes and streambanks are better
stabilized when a biodegradable revegetation fabric is used to hold the
reinforced soil lifts in place between the plant layers. Plant material placed
using brush layering provides fish habitat and nutrients to the adjacent water
body.

Collection, storage and planting information are described under Dormant

Cuttings in the Plant Care and Preparation section. Different species of woody
cuttings that root easily (see Plant Species Selection List, Shrubs and Trees)
can be mixed in the layers; rooted plants can also be added to create a hedge-
brush layer (see Root Pruning under the Plant Care and Preparation section).
Rooted plants may be planted throughout the growing season from spring through
early fall. Dormant plants, if collected in the spring, should be planted before
July 1 of that year.

Choose a technique such as root wads, live siltation, coir logs, or cabled
spruce tree revetments to secure the toe of the slope. Consult streambank
revegetation professionals and evaluate site conditions to determine the
treatment of the toe-of-slope. Perform all construction activities during
periods of dry riverbed; dewater area, or isolate the work area (see Erosion
Control section). Along a water body, the first brush layer typically occurs at
the OHW (ordinary high water) level, often identified by the line of growing
vegetation (plus other factors).

Prepare a bench, which corresponds to the bank depth necessary to stabilize the
slope, either through excavation or building up the slope, so that it angles
slightly down and into the bank. It is important to note the upstream and
downstream riparian species and slope height and angle when designing a brush
layer project. Specifications should represent the local native environment as
much as possible. If the surrounding area has been greatly impacted, observation
further upstream and downstream may be necessary. Place fifteen dormant branches
on the bench per foot or ten rooted cuttings per foot, slightly crisscrossed
(see Hedge Brush Layering/Brush Layering, Step-by-Step). A mixture of dormant
cuttings and rooted plants may be used. The cut or rooted ends are placed into
the slope with the tips extending beyond the edge of the bench no more than 1/4
of the total branch length. Place 2 to 4 inches of soil on top of the branches,
water and tamp into place. The reinforced soil lift is placed directly on top of
the brush layer, pulling the next step back according to the designed bank
angle. Two revegetation fabrics are used in reinforced soil lifts to keep soil
in place when a brush layer is installed on steep slopes and streambanks. The
first fabric layer, a fine mesh fabric (example: Bon Terra’s® ENC2, North
American Green’s C125 BN, or equivalent) is placed inside the larger mesh fabric
(example: Bon Terra’s® CF7, North American Green’s CCM-700, or equivalent).
Next, 12-14 inches of soil-topsoil mix is placed on top of the fabric, watered,
compressed and 2-3 feet of fabric is rolled over the top and secured in place
with wooden stakes. Follow this step by another layer of dormant cuttings/rooted
plants.

Repeat the branch, topsoil, wrapped soil/topsoil mix layering sequence until the
desired bank height is achieved (see Hedge Brush Layering/Brush Layering, Step-
by-Step). Trim plants back to 1/4 of the planting above ground, 3/4 of the
planting below ground. A vegetation mat may be placed on the top layer of the
bank after the last brush layer is installed and overtopped with soil. The
vegetative mat should be harvested and installed according to the Transplanting
section and the shoots should be cut back by 1/3 to compensate for root loss and
to encourage new root growth.

Higher density plantings are needed for more erosive sites and if the diameter
of the plant material is small. Sites with a shallow slope and low erosion
potential can have wider vegetation spacing than sites with a steep slope and
higher erosion potential. This technique can be easily mechanized, layer-by-
layer, if it is installed during construction of a fill slope. On cut slopes and
existing banks each layer must be excavated.

Advantages:
• Prevents soil erosion and stabilizes bank
• Provides fish habitat and native vegetation
• Reestablishes healthy riparian zone functions
• May be used in higher velocity systems, dependant on toe-of-slope
protection
• High success rate
• No permanent geotextile fabrics or metal left in bank

Disadvantages:
• Relatively expensive
• More technologically challenging, requires expertise
• May require heavy machinery
• Requires isolated work area to prevent water body siltation
• Very stable, dependent on toe-of-slope stabilization
• May require significant training