0910367
nd
2 July 2009
catalogue section 40 & 75
Keystart 7210/7211
Engine and Generator Control Modules
• Manual start/stop
• Keyswitch operation
• Timed preheat output
• Automatic fault shutdowns
• Overspeed shutdown, magnetic
pickup or generator AC driven
• Front-of-panel mounted
Description Product specifications
Keystart 7210 and 7211 control modules provide manual power supply:
start/stop and automatic fault protection for generators, pumps
operating voltage:
and other engine-driven applications. steady state 7 – 30 VDC
Operator control is by a 3 position keyswitch. The key is brown out / cranking 5 VDC
common to all Keystarts and removable only in the Stop/Reset current consumption < 100mA
(O) position. Outputs are provided for the control of engine fuel inputs:
(energized to run), starter motor and preheat. The Keystart also
fault switch inputs: close to negative DC during fault
has an alarm output for remote/audible warning of faults.
–ve input defined as: –1V to +1V w.r.t. – ve DC supply
Indication of engine status and faults is by six LEDs and icons. speed sensing inputs:-
Fault shutdown switch inputs (closing to negative on fault) are generator AC 70 – 270 VAC rms, <50 to >60 Hz.
provided for engine low oil pressure, high engine temperature default setting: 50 or 60 Hz
and auxiliary/plant fault. Model 7211 has a fully adjustable mag pickup/transducer 3.5 – 21 VAC rms, <2000 to >6500 Hz.
engine overspeed shutdown, driven by generator AC or
magnetic pickup. Charge alternator excitation and a charge outputs: (all ratings non-reactive)
fail warning LED are fitted as standard. run (fuel), preheat positive DC, switched NO relay contact,
1 A max. @ 24V DC
Electrical connection is by quick-connect, spring-clamp terminal
start (crank) positive DC via keyswitch contacts,
blocks. A universal 7 to 30VDC power supply allows operation
16 A max. @ 24V DC
with 12 or 24VDC engine batteries, with engine crank-dip
alarm (fault) negative DC (open collector
voltage protection fitted as standard. NPN transistor), 100mA max.
Keystarts are front-of-panel mounted through a standard speed calibration to suit 0 – 1 mA, 75 Ohm meter
square cut-out, and secured at the rear with two mounting clips. output = 0.75mA at rated engine speed
adjustable settings:
preheat timer 0 to 20 secs, default setting 0 secs
fault override timer 2 to 20 secs, default setting 10 secs
overspeed trip level 100 to 130 % of calibrated speed,
default setting 110%
general:
Warranty
overall dimensions (w x h x d) 72 x 72x 100 mm /
2.83 x 2.83 x 3.94 in.
A two year limited warranty on materials and workmanship panel cut-out size DIN 68 x 68 mm / 2.68 x 2.68 in.
is given with this product. Full details are available at weight approx 300 g / 0.7 lb
[Link]/warranty operating ambient temperature –10 to +55°C / 14 to 131°F
In order to consistently bring you the highest quality, full featured products, we reserve the right to change our specifications and designs at any time.
MURPHY, the Murphy logo, are registered and/or common law trademarks of Murphy Industries, Inc. This document, including
textual matter and illustrations, is copyright protected by Frank W Murphy Ltd., with all rights reserved. © 2009 Frank W Murphy Ltd.
Front view and operation Rear view, connection and settings
How to order Typical connection
Stock code Model / description
76.70.1166 KEY7210 Keystart, no overspeed
76.70.1167 KEY7211 Keystart, AC/MPU overspeed*
* Note: stock units are set to AC sensing, nominal 50Hz. To select
magnetic pickup sensing, adjust internal circuit board link J1.
Further information
Document Description
00-02-0678 Keystart 7210/9610 series installation
FW MURPHY FRANK W. MURPHY LTD. FW MURPHY INTERNATIONAL TRADING (SHANGHAI) CO., LTD.
P.O. Box 470248, Tulsa, Oklahoma 74147 USA Church Road, Laverstock, Suite 1704, Tower B, City Center of Shanghai, 100 Zunyi Road
+1 918 317 4100 Fax: +1 918 317 4266 Salisbury, SP1 1QZ, United Kingdom Shanghai, 200051, China
E-mail: sales@[Link] Tel: +44 1722 410055 Phone: +86 21 6237 2082 Fax: +86 21 6237 2083
INDUSTRIAL PANEL DIVISION Fax: +44 1722 410088 E-mail: mhong@[Link]
Fax: +1 918 317 4124 E-mail: sales@[Link] FW MURPHY INSTRUMENTS (HANGZHOU) CO., LTD.
E-mail: ipdsales@[Link] Web: [Link] 77 23 rd Street, Hangzhou Economic & Technological Development Area
MURPHY POWER IGNITION COMPUTRONIC CONTROLS Hangzhou, Zhejiang, 310018, China
Website: [Link] 41 – 43 Railway Terrace, Nechells, Phone: +86 571 8788 6060 Fax: +86 571 8684 8878
Birmingham, B7 5NG, United Kingdom
CONTROL SYSTEMS AND SERVICES DIVISION Tel: +44 121 327 8500
P.O. Box 1819, Rosenberg, Texas 77471 USA Fax: +44 121 327 8501
Phone: +1 281 633 4500 Fax: +1 281 633 4588 E-mail: sales@[Link]
E-mail: css-solutions@[Link] Web: [Link]
