Bosch Motorsport | Engine Control Unit MS 7.
Engine Control Unit MS 7.8
Optimized for low- and high-pressure injection
5 CAN, 3 of them CAN-FD capable
4 x 8.5 A H-Bridge
Gearbox control optionally included
SENT sensor support
The MS 7.8 engine control unit manages gasoline en- • alternatively, up to 12 drivers for use with external power
gines up to 12 cylinders. The MS 7 line features a stages
powerful digital processing core with floating point
Physical engine model for fast application
arithmetic and a high-end FPGA for ultimate per-
formance and flexibility. The MS 7 line utilizes a • determine engine load by throttle position or air pressure sig-
software development process based on MATLAB/Si- nals
mulink which significantly speeds up algorithm de- • mixture control and basic ignition guided by main signal relat-
velopment by using automatic code and documenta- ive load rl
tion generation. Custom functions can be generated • Subsystems pit speed-, launch-, rpm-limiter and ASR are in-
quickly and easily. The flexible hardware design al- tegrated inside torque control
lows the MS 7.8 to support complex or unusual en- • Separated power cut functions to assist several gear cut sys-
gine or chassis configurations. tems
Version MS 7.8-ADV was developed for use with • Diagnostics
Lambda Sensor LSU ADV (higher max. Hexagon tem- • Integrated safety strategy for 2 electronic throttle controls
perature).
Integrated support of manual gearshift
Application Electronic throttle control
Variable Valve Timing VVT
High pressure injection Turbo control
Integrated power stages for triple injection and use of: Traction control
• 4 cylinders up to 14,600 rpm Launch control
• 6 cylinders up to 9,700 rpm
LTE Ethernet telemetry support
• 8 cylinders up to 7,300 rpm
Internal logger
(for supply voltages >10 V, depending on injection types and
• FULL_LOG_1 (4 GB memory on Recording 1) enabled
pressure ranges)
• PERF_LOG_1 (16 GB memory on Partition 1) optional
HP package for flat and V-engines inclusive (2nd Bank, fuel con- • FULL_LOG_2 (4 GB memory on Recording 2) enabled
trol valve 2, external cylinder 9-12) • DATA_USB (Data copy to USB flash drive) enabled
Low pressure injection Logging rates
• Max. 12 cylinders up to 16,000 rpm, high impedance inject- • Usage of all features: 400 kB/s
ors only • Primary logging use case: >800 kB/s
Outputs can be used alternatively as low side switches 2.2 A with • Logging data download rate: up to 6.2 MB/s
fast decay
Ignition
• 8 integrated power stages up to 20 A
Bosch Motorsport | Engine Control Unit MS 7.8 2|4
Technical Specifications Outputs
38 function related outputs
Mechanical Data
High Pressure Injection
Milled aluminum housing
2 x high pressure pump with fuel control valve
4 motorsport connectors, 264 pins in total
8 x high pressure injection for magnetic injectors
Size without connectors 198 x 180 x 42 mm
Low Pressure Injection
Weight 1,560 g
12 x 2.2 A low pressure injection for high impedance inject-
Protection Classification IP67
ors
Temp. range (at internal -20 to 85°C
Ignition
sensors)
12 x ignition control, IGBT or BJT, coils with integrated
Max. Vibration Vibration Profile 1 (see Down-
power stage, or max. 8 cylinders and coils without integrated
loads or [Link]-
power stage, 20 A
[Link])
2 x 8.5 A H-bridge reserved for electronic throttle
Electrical Data
2 x 3 A pwm lowside switch for Lambda heater
Power supply 6 to 18 V
15 freely configurable outputs
CPU Dual Core 1 GHz, FPGA
2 x 8.5 A H-bridge
Inputs
2 x 4 A pwm lowside switch
46 analog inputs 6 x 3 A pwm lowside switch
8 analog/digital/SENT inputs (shared) 4 x 2.2 A pwm lowside switch
1 x 1 A pwm lowside switch low dump resistant
12 digital inputs
4 x switchable Hall/inductive 5 output signals
4 x Hall 5 x MUX outputs for internal signals like flywheel, knock sig-
nals, cylinder pressure
4 x switchable Hall/DF11
Adaptation and Documentation
21 internal measurements
Configuration
8 x ECU Current (Sensor Supply)
Configurable flywheel- and trigger disc geometries
8 x ECU Voltage (Sensor Supply) Selectable links between functions and in- or outputs
1 x Boost Voltage Function documentation
1 x Booster Supply Voltage Automatically created during code generation
1 x Dynpwr Supply Voltage MatLab code generation
1 x Supply Current Support for customer own MatLab function development
1 x USB Current Software Tools (free download)
18 function related inputs Data Analysis tool WinDarab V7
8 x fast ADC for combustion chamber pressure input System Configuration tool RaceCon [Link] or later
2 x thermocouple exhaust gas temperature sensors (multi- Mating Connectors
type)
LIFE (red) AS618-35SN
2 x Lambda interfaces for LSU 4.9 sensor types (LSU-ADV
Actuator (blue) AS618-35SB
version available, see Ordering Information)
Combined (orange) AS618-35SC
1 x digital switch for engine ON/OFF
Sensor (yellow) AS618-35SA
1 x digital input for beacon receiver
4 x knock sensors Communication
Sensor supplies and screens
1 Ethernet 1 Gbit
8 x sensor supply 400 mA, switchable 5 V/Vbat with voltage and
3 Ethernet 100 Mbit
current sensing
5 CAN, 3 of them CAN-FD capable
8 x sensor grounds
1 LIN
2 x sensor screens
1 USB
Bosch Motorsport | Engine Control Unit MS 7.8 3|4
8 SENT • Cylinder pressure detection base package
1 Time sync synchronization Ethernet • Knock detection via cylinder pressure evaluation
• Programming interface cable
2 Network screens
Ordering Information
Installation Notes
Engine Control Unit MS 7.8
Inspection services recommended after 220 h or 24 months, in- Order number F02U.V03.249-02
ternal battery to be replaced during service.
Engine Control Unit MS 7.8-ADV
Depending on your experiences with calibration of ECUs we re- Order number F02U.V03.316-02
commend calibration support from Bosch Motorsport. Rugged USB flash drive
Please remember that the mating connectors and the program- Order number F02U.V03.534-01
ming interface cable are not included and must be ordered separ- Connector for USB flash drive on car loom side
ately. Order number F02U.002.996-01
Adapter cable to PC USB-Port
Legal Restrictions Order number F02U.V01.343-01
The sale of this product in Mexico is prohibited. Software Options
Due to embargo restrictions, sale of this product in CCA Hardware Upgrade per device
Russia, Belarus, Iran, Syria, and North Korea is pro- Order number F02U.V02.137-01
hibited. PERF_LOG_1
Order number F02U.V03.054-01
Upgrades
Gear Control Package 1
Order number please contact MEGA-Line
CCA Hardware Upgrade per device
Gear Control Package 2
Enable Customer Code Area Order number F02U.V02.264-01
PERF_LOG_1 Cylinder pressure detection base package
Order number F02U.V02.543-01
Increase logging Partition 1 from 4 GB to 16 GB memory
Knock detection via cylinder pressure evaluation
Gear Control Package 1 Order number F02U.V02.544-01
Gear control MEGA-Line functionality, has to be used with MEGA- Accessories
Line components (License model via MEGA-Line) Breakout Box BOB 66-pole, Connector code blue
-- Link to MEGA-Line Support Request-- Order number F02U.V02.295-01
-- Link to MEGA-Line License Request Form -- Breakout Box BOB 66-pole, Connector code orange
Order number F02U.V02.296-01
Gear Control Package 2 Breakout Box BOB 66-pole, Connector code yellow
Gear control Bosch Motorsport functionality Order number F02U.V02.298-01
Breakout Box BOB MS 7, LIFE-Connector code red
Accessories Order number F02U.V02.293-02
• Rugged USB flash drive Programming interface cable
• Mating connector for USB flash drive on car loom side Order number F02U.V02.327-01
• Adapter cable to PC USB-Port
Bosch Motorsport | Engine Control Unit MS 7.8 4|4
Dimensions
See Offer Drawing for further information
Represented by:
Europe: North America: Asia-Pacific: Australia, New Zealand and South
Bosch Engineering GmbH Bosch Engineering North America Bosch Engineering Japan K.K. Africa:
Motorsport Motorsport Motorsports Department Robert Bosch Pty. Ltd
Robert-Bosch-Allee 1 38000 Hills Tech Drive 1-9-32 Nakagawa Chuo, Tsuzuki-ku Motorsport
74232 Abstatt Farmington Hills, MI 48331-3417 Yokohama City 1555 Centre Road
Germany United States of America Kanagawa Prefecture 224-8601 Clayton, Victoria, 3168
Tel.: +49 7062 911 9101 Tel.: +1 248 876 2977 Japan Australia
Fax: +49 7062 911 79104 Fax: +1 248 876 7373 Tel.: +81 45 605 3032 Tel.: +61 (3) 9541 3901
motorsport@[Link] motorsport@[Link] Fax: +81 45 605 3059 [Link]@[Link]
[Link] [Link] [Link]
© Bosch Engineering GmbH 2024 | Data subject to change without notice
326508043 | en, , 30. Sep 2024
