LED Blink
void setup()
{
pinMode(13,OUTPUT);// put your setup code here, to run once:
void loop()
{
digitalWrite(13,HIGH);
delay(1000);
digitalWrite(13,LOW);
delay(1000);
// put your main code here, to run repeatedly:
}
Vibration sensor
// include the library code:
int b1 = 2;
int d1 = 5;
int cnt=0,cnt2;
int timer=0;
// a maximum of eight servo objects can be created
int pos = 0; // variable to store the servo position
void setup() {
Serial.begin(9600); //initialize serial
pinMode(b1, INPUT_PULLUP);
pinMode(d1, OUTPUT);
digitalWrite(d1, HIGH);
digitalWrite(d1,LOW);
delay(300); // wait for a second
cnt=0;
void loop() {
if(digitalRead(b1) == HIGH){
Serial.println("VIBRATION ALERT");
digitalWrite(d1, HIGH);
delay(300); // wait for a second
// wait for a second
digitalWrite(d1, LOW);
delay(300);
digitalWrite(d1, HIGH);
delay(300); // wait for a second
digitalWrite(d1, LOW);
delay(300); // wait for a second
digitalWrite(d1, HIGH);
delay(300); // wait for a second
digitalWrite(d1, LOW);
delay(300); // wait for a second
Vibration sensor
Ultrasonic Sensor
const int echoPin = 2; // Echo Pin of Ultrasonic Sensor
const int pingPin = 3; // Trigger Pin of Ultrasonic Sensor
void setup()
Serial.begin(9600); // Starting Serial Communication
pinMode(pingPin, OUTPUT); // initialising pin 3 as output
pinMode(echoPin, INPUT); // initialising pin 2 as input
void loop()
long duration, inches, cm;
digitalWrite(pingPin, LOW);
delayMicroseconds(2);
digitalWrite(pingPin, HIGH);
delayMicroseconds(10);
digitalWrite(pingPin, LOW);
duration = pulseIn(echoPin, HIGH); // using pulsin function to determine total time
inches = microsecondsToInches(duration); // calling method
cm = microsecondsToCentimeters(duration); // calling method
Serial.print(inches);
Serial.print("in, ");
Serial.print(cm);
Serial.print("cm");
Serial.println();
delay(100);
long microsecondsToInches(long microseconds) // method to covert microsec to inches
return microseconds / 74 / 2;
long microsecondsToCentimeters(long microseconds) // method to covert microsec to centimeters
return microseconds / 29 / 2;
Ultrasonic Sensor
LDR
// the setup routine runs once when you press reset:
void setup() {
// initialize serial communication at 9600 bits per second:
Serial.begin(9600);
pinMode(10,OUTPUT);
// the loop routine runs over and over again forever:
void loop() {
// read the input on analog pin 0:
int sensorValue = analogRead(A0);
// print out the value you read:
Serial.println(sensorValue);
if(sensorValue < 50)
digitalWrite(10,HIGH);
else
digitalWrite(10,LOW);
delay(1); // delay in between reads for stability
}
LDR
Temperature Notification
float temp;
void setup() {
pinMode (13, OUTPUT);
Serial.begin (9600);
void loop() {
temp= analogRead (A0);
temp= (temp*500)/1024;
Serial.println (temp);
if (temp>30)
digitalWrite (13, HIGH);
else
digitalWrite (13, LOW);
delay (1000);
Temperature Notification
program to sense the available networks using Arduino
#include <SPI.h>
#include <WiFiNINA.h>
void setup() {
//Initialize serial and wait for port to open:
Serial.begin(9600);
while (!Serial) {
; // wait for serial port to connect. Needed for native USB port only
// check for the WiFi module:
if (WiFi.status() == WL_NO_MODULE) {
Serial.println("Communication with WiFi module failed!");
// don't continue
while (true);
String fv = WiFi.firmwareVersion();
if (fv < WIFI_FIRMWARE_LATEST_VERSION) {
Serial.println("Please upgrade the firmware");
// print your MAC address:
byte mac[6];
WiFi.macAddress(mac);
Serial.print("MAC: ");
printMacAddress(mac);
}
void loop() {
// scan for existing networks:
Serial.println("Scanning available networks...");
listNetworks();
delay(10000);
void listNetworks() {
// scan for nearby networks:
Serial.println("** Scan Networks **");
int numSsid = WiFi.scanNetworks();
if (numSsid == -1) {
Serial.println("Couldn't get a wifi connection");
while (true);
// print the list of networks seen:
Serial.print("number of available networks:");
Serial.println(numSsid);
// print the network number and name for each network found:
for (int thisNet = 0; thisNet < numSsid; thisNet++) {
Serial.print(thisNet);
Serial.print(") ");
Serial.print(WiFi.SSID(thisNet));
Serial.print("\tSignal: ");
Serial.print(WiFi.RSSI(thisNet));
Serial.print(" dBm");
Serial.print("\tEncryption: ");
printEncryptionType(WiFi.encryptionType(thisNet));
}
}
void printEncryptionType(int thisType) {
// read the encryption type and print out the title:
switch (thisType) {
case ENC_TYPE_WEP:
Serial.println("WEP");
break;
case ENC_TYPE_TKIP:
Serial.println("WPA");
break;
case ENC_TYPE_CCMP:
Serial.println("WPA2");
break;
case ENC_TYPE_NONE:
Serial.println("None");
break;
case ENC_TYPE_AUTO:
Serial.println("Auto");
break;
case ENC_TYPE_UNKNOWN:
default:
Serial.println("Unknown");
break;
void printMacAddress(byte mac[]) {
for (int i = 5; i >= 0; i--) {
if (mac[i] < 16) {
Serial.print("0");
}
Serial.print(mac[i], HEX);
if (i > 0) {
Serial.print(":");
Serial.println();
