Scribd
Upload
59 views2 pages

Unit 3 4 5 Questions

The document outlines various concepts related to amplifiers, power supplies, and feedback systems, including gain-bandwidth product, Miller's theorem, and the significance of feedback in amplifiers. It includes calculations for amplifier gain at specific frequencies, the advantages and disadvantages of linear power supplies, and the properties of negative feedback amplifiers. Additionally, it discusses the importance of components like capacitors and diodes in power supply circuits.

Uploaded by

Barath Ganesh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
59 views2 pages

Unit 3 4 5 Questions

The document outlines various concepts related to amplifiers, power supplies, and feedback systems, including gain-bandwidth product, Miller's theorem, and the significance of feedback in amplifiers. It includes calculations for amplifier gain at specific frequencies, the advantages and disadvantages of linear power supplies, and the properties of negative feedback amplifiers. Additionally, it discusses the importance of components like capacitors and diodes in power supply circuits.

Uploaded by

Barath Ganesh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd

Unit 3: PART-A

1. Gain bandwidth frequency is GBP= 3000 MHz. The cut-off frequency is f=10MHz. What
is the CE short circuit current gain at the β cut-off frequency?
2. What is meant by gain-bandwidth product?
3. Relate gain and bandwidth of single and multi-stage amplifier.
4. Define beta cutoff frequency.
5. State Miller’s theorem.
6. What is meant by Miller effect?
7. State the significance of Miller's capacitance.
8. Sketch the small signal analysis of full hybrid model.
9. Mention the importance of the resistor r_bb in the transistor hybrid model.
10. Define rise time.
11. Write the relation between the sag and lower cutoff frequency.
12. Sketch the two-port network model for Cµ.
13. Draw the Thevenin equivalent circuit of Miller effect.
14. Define rise time. Give the relation between bandwidth and rise time.
15. If the mid-band gain of an amplifier is 100 and the half-power frequencies are f_L =
40Hz and f_H =16KHz, calculate the amplifier gain at 20 Hz and 20 kHz frequency.

Unit 4: PART-A
16. List the advantages and disadvantages of linear power supply.
17. Define Line and Load regulation of voltage regulator.
18. Sketch the block diagram of LMPS.
19. What is the function of protection circuits in the power supply?
20. Calculate the value of capacitance to use in capacitor filter connected to FWR with 400
Hz frequency, ripple factor is 10% of load 500 ohm.
21. How to protect the system from overvoltage problem?
22. Compare SMPS with linear power supply.
23. Define Transformer Utilization Factor.
24. Define ripple factor of a rectifier.
25. What is meant by switching regulator?
26. What is the importance of peak inverse voltage?
27. Why diodes are not operated in the breakdown region in rectifiers?
28. State the advantages of bleeder resistor.
29. Sketch the CLC filter.
30. Mention the types of SMPS.

Unit 5: PART-A
31. List out the advantages of negative feedback.
32. Draw the general feedback structure.
33. List the properties of negative feedback amplifier.
34. Name the types of feedback topologies.
35. Calculate the closed-loop gain of the amplifier if the open-loop gain is 1,00,000 and
feedback factor is 0.01.
36. Define sensitivity and desensitivity of gain in feedback amplifiers.
37. What is meant by return ratio in feedback amplifier?
38. What is the impact of negative feedback on noise in circuits?
39. State the effect on input and output resistance of amplifier if voltage series negative
feedback is employed.
40. An amplifier has an open-loop gain of 1000 and a feedback ratio of 0.04. If the open-loop
gain changes by 10% due to temperature variation, find the % change in gain of the
amplifier with feedback.
41. Sketch the Current shunt feedback topology.
42. Sketch the Shunt shunt feedback topology.
43. The distortion in an amplifier is found to be 3%, when the feedback ratio of negative
feedback amplifier is 0.04. When the feedback is removed, the distortion becomes 15%.
Find the open and closed-loop gain.
44. What is the effect of upper cut-off and lower cut-off frequency with negative feedback?
45. Give the expression for gain of an amplifier with negative feedback.

You might also like