USBtin EB – USB to CAN interface board
Datasheet
USBtin is an open source USB to CAN interface. It can monitor CAN buses and transmit CAN
messages. All common CAN baud rates are supported. USBtin implements the USB CDC class and
creates a virtual COM port on the host computer. Via this serial port, the interface is controlled by
means of simple commands.
d = 3.2 mm
3 mm
3 mm
25 mm
Bootloader Termination
57 mm
Main features
• USB powered (no isolation between USB and CAN ground)
• Control over any serial terminal program with simple serial protocol
• Presets for common baud rates (10k ... 1M)
• Timstamping of incoming messages
• Listen-only and active mode
• CAN ID filtering, e.g. for high-loaded busses
• 120 Ohm termination via jumper
• Open source GUI and Java Library available
V2.3 © 2015-2021 Thomas Fischl, http://www.fischl.de/usbtin/
USBtin EB – USB to CAN interface board Datasheet
Connection
USBtin EB has a mini-USB connector for communication with the host computer via a standard
mini-USB cable. The CAN bus is routed to three pins (CON2): CAN-H, CAN-L and ground. The
spacing of these three pins is 3.5mm and fits for standard RM3.5 connectors, e.g. Reichelt „AKL
182-03“ or Conrad „729906-62“.
Driver installation
On Linux, MacOS and Windows >8 systems there is no need for drivers, the CDC is automatically
detected and mapped to an virtual com port „/dev/ttyACMx“ or „COMx“. For Windows <8, there is
a driver file available (http://www.fischl.de/usbtin/#drivers).
Software
USBtin is controlled by means of simple commands via
the virtual serial port. This commands can be sent with any
serial terminal program. There is also USBtinViewer, a
simple muli-platform GUI. For own developments, there
exists USBtinLib, an open source Java Library. Further
information about the software and a list of serial
commands can be found on http://www.fischl.de/usbtin/.
Termination
120 Ohm termination can be activated via the termination jumper (JP2, 2.54mm) or via the solder
jumper on the bottom of the board (JP3).
LED signaling
Flashing: USBtin is idle, in configuration mode and can channel is closed.
Permanent on: CAN channel is open.
Firmware update
1. Short bootloader jumper (JP1, 2.54mm) and connect USBtin to host USB
2. Download bootloader tool „mphidflash“ from
https://github.com/AdamLaurie/mphidflash/tree/master/binaries
3. Start firmware upload with command line command:
mphidflash -write USBtin_firmware_vX.X.hex -reset
4. Unplug USBtin from host and remove bootloader jumper (JP1)
Throughput
The serial protocol limits the bandwidth that can be used by USBtin to send and receive CAN
messages. Firmware v1.5 was tested successfully receiving 100% load on 250 kBaud bus (~2000
can messages per second). Testconditions: Standard 11bit id, 8 data bytes, timestamping disabled.
Testsystem: Lubuntu 14.04 on Intel(R) Core(TM)2 Duo CPU [email protected] with 4 GB ram.
V2.3 © 2015-2021 Thomas Fischl, http://www.fischl.de/usbtin/
2/3
USBtin EB – USB to CAN interface board Datasheet
Schematics diagram
Evaluation board notice
USBtin EB is an evaluation board intended for use for engineering development or evaluation
purposes in laboratory enviroment only. It is not considered as an end user application. If you intend
to use it in an end-product, you have to ensure in your own responsibility that the device meets the
relevant regulations (e.g. CE, FCC).
V2.3 © 2015-2021 Thomas Fischl, http://www.fischl.de/usbtin/
3/3
