Seat No.: ________ Enrolment No.
___________
GUJARAT TECHNOLOGICAL UNIVERSITY
BE- SEMESTER 1st / 2nd EXAMINATION (OLD SYLLABUS) – SUMMER - 2017
Subject Code: 110013 Date:08/06/2017
Subject Name: Engineering Graphics
Time: 2:30 PM to 05:30 PM Total Marks: 70
Instructions:
1. Attempt any five questions.
2. Make suitable assumptions wherever necessary and mention it clearly.
3. Figures to the right indicate full marks.
4. Draw neat sketches wherever required to justify the answer.
5. Don’t rube construction lines.
Q.1 (a) OPA is an offset slider crank chain, crank OP is 30 mm long and rotates 07
in clockwise direction. Connecting rod AP is 130 mm long and the offset is 40
mm. Draw the loci of two points - M (midpoint of AP) and R on the extension
of connecting rod AP at distance equal to PR = 30 mm.
(b) (i) Write shortnote on: Aligned system and uni-directional system of 03
dimensioning.
(ii) On a map of Gujarat, 1 cm represents 5 kms. Construct a plain scale long 04
enough to measure a distance between Sanand and Surendranagar – 100
kms. Also indicate the distance between Surendranagar and Viramgam – 65
kms.
Q.2 (a) A straight line AB is 75 mm long and inclined at 350 to H.P and 550 to V.P. The 07
end A on the H.P and 15 mm in front of V.P. Draw projections of straight line
AB assuming to be in the first quadrant.
(b) A circle of 50 mm diameter rolls along a straight line without slipping. Draw 07
the curve traced out by the point P on the periphery of the circle. Take the initial
position the point P at the bottom on vertical centre line of the circle. Name the
curve.
Q.3 (a) A pentagonal pyramid of base edge 30 mm and height 60 mm rests on the HP 07
such that one of its edge of base is parallel to and nearer to the VP. The pyramid
is cut by a plane inclined 40º to the HP at 35 mm on axis from base of the
pyramid. Draw the lateral development of the truncated pyramid.
(b) A line AB 75 mm long is inclined at 35˚ to the V.P. The end A is 20 mm above 07
the H.P and 15 mm in front of V.P. The plan length of the line is 50 mm. Draw
projections of straight line AB assuming to be in the first quadrant and find the
inclination with H.P.
Q.4 (a) Two fixed points P and Q are 80 mm apart. Trace the complete path of a point P 07
moving (in the same plane as that of P and Q) in such a way that, the
sum of its distances from P and Q is always the same and equal to 100 mm.
Name the curve.
(b) A thin 30˚-60˚ set square has its longest edge in the V.P. and inclined at 30˚ the 07
H.P. The length of the shortest side is 35 mm. Its surface makes an angle of 45˚
with the V.P. Draw the projections of set square.
Q.5 (a) A cylinder, diameter of base 70 mm and axis 90 mm is resting on one of its 07
generator on the H.P. with its axis remaining parallel to V.P. It is cut by an
A.V.P. inclined to the V.P. by 300 and passing through the point on the axis 50
mm from its one end. Draw sectional elevation, sectional end view and plan
showing the cutting plane.
1
(b) A square pyramid, base 30 mm side and axis 70 mm long, is resting on H.P. on 07
one of its corner of its base in such a way that slant edge opposite to the corner
on H.P. is making an angle of 300 to H.P and 350 to V.P. Draw its projections.
Q.6 (a) Answer the following (any ONE) : 04
(i) List and draw basic types of lines recommended by BIS.
(ii) Engineering graphics is a language of all persons involved in
engineering activities. Explain the given statement.
(b) Draw the isometric view from the following given orthographic views 10
(figure no. 1).
figure no. 1
figure no. 1
Q.7 (a) Answer the following (any ONE) : 04
(i) Explain the 3rd angle orthographic projection system. Draw the symbols of
1st and 3rd angle orthographic projection system.
(ii) Write short note on BIS SP-46 engineering drawing standard.
(b) The figure no. 2 shows the pictorial view of the object. Draw the front view, top 10
view and and left hand side view using first angle method of projection.
figure no. 2
