PROOP Quick Start Guide
Preface
PROOP, is designed to provide interaction between the user and the automation systems based on
industrial PLC systems. This document will be helpful the user to install and connect PROOP.
• Before begin the installation of this product, please read the instruction manual.
• For the information of PROOP Builder software and installation, refer to the PROOP Builder user
manual.
• The contents of the document may have been updated. You can access the most updated version at
www.emkoelektronik.com.tr
This symbol is used for safety warnings. User must pay attention to these warnings.
General Features
PROOP 4.3’’& 5” SERIES
Models
Proop.black-4.eco Proop.black-5.eco
Display Type 4.3” TFT LCD 5” TFT LCD
Display Colors 260K colors
Resolution 480 x 272 800 x 480
LCD Backlight LED Backlight
Touch Method Resistive Analog
Brightness 500 400
Backlight Life min. 50000 hours at 25°C
MCU ARM Cortex-A7, 800Mhz
Flash Memory 8 GB
RAM 512 MB DDR3 SDRAM
Buzzer N/A
USB Device 1x USB 2.0
USB Host 1x USB 2.0
Seri Com-2 RS-485 (Terminal)
Seri Com-3 RS-232 (Terminal)
Seri Com-4 N/A
Ethernet N/A
Digital Inputs N/A
Digital Outputs N/A
Analog Inputs N/A
Analog Outputs N/A
Real Time Clock Built in
Operating Voltage 18…30Vdc
Power Consumption 5W
RTC Battery CR2032 button cell lithium battery, 3V(removable)
RTC Battery Life 5 years
Operating Temperature 0…50°C
Storage Temperature -20…60°C
Operating Humidity 0…90%RH (non condensed)
Dimensions 153 x 105 x 40.5 mm
Panel Cut-out 139 x 94 mm
Weight 350 g
1 Quick Start Guide EN PROOP 03 V04 01/24
PROOP 7’’ SERIES
Proop.black-7C.E2
Proop.black-7.eco
Proop.black-7C.E
Proop.black-7L.E
Proop.black-7C
Proop-7C.E2
Proop-7C.E
Proop-7L.E
Proop-7C
Proop-7L
Models
Display Type 7” TFT LCD
Display Colors 260K Colors
Resolution 800 x 480
LCD Backlight LED Backlight
Touch Method Resistive Analog
Brightness 360 cd/m2
Backlight Life min. 50000 hours at 25°C
MCU ARM Cortex-A7, 800Mhz
Flash Memory 8 GB
RAM 512 MB DDR3 SDRAM
Buzzer >=85 dB
USB Device 1x USB 2.0
USB Host 1x USB 2.0
Seri Com-2 RS-485 (Terminal)
Seri Com-3 RS-232 (Terminal)
Seri Com-4 N/A RS-232 (DB-9 Socket)
Ethernet N/A 10/100 Mbps N/A 10/100 Mbps 2x10/100 Mbps
Digital Inputs N/A 4x Digital
Digital Outputs N/A 4x Digital
Analog Inputs N/A
Analog Outputs N/A
Real Time Clock Built in
Operating Voltage 18…30Vdc
Power Consumption 6W
RTC Battery CR2032 button cell lithium battery, 3V(removable)
RTC Battery Life 5 years
Operating Temperature 0…50°C
Storage Temperature -20…60°C
Operating Humidity 0…90%RH (non condensed)
Dimensions 206 x 152 x 50 mm
Panel Cut-out 196 x 142 mm
Weight 700 g
2 Quick Start Guide EN PROOP 03 V04 01/24
PROOP 10’’ SERIES
Proop.black-10P.E2
Proop.black-10C.E
Proop.black-10L.E
Proop.black-10P.E
Proop.black-10C
Proop.black-10P
Proop.black-10L
Proop-10P.E2
Proop-10C.E
Proop-10L.E
Proop-10P.E
Proop-10C
Proop-10P
Proop-10L
Models
Display Type 10.1” TFT
Display Colors 16M colors
Resolution 1024 x 600
LCD Backlight LED Backlight
Touch Method Resistive Analog
Brightness 350
Backlight Life min. 50000 hours at 25°C
MCU ARM Cortex-A9, 800Mhz
Flash Memory 8 GB
RAM 512 MB DDR3 SDRAM
Buzzer >=85 dB
USB Device 1x USB 2.0
USB Host 1x USB 2.0
Seri Com-2 RS-485 (Terminal)
Seri Com-3 RS-232 (Terminal)
Seri Com-4 RS-232 (DB-9 Socket)
Ethernet N/A 10/100 Mbps N/A 10/100 Mbps N/A 10/100 Mbps 2x 10/100 Mbps
Digital Inputs N/A 5x Digital
Digital Outputs N/A 4x Digital
Analog Inputs N/A N/A 2x 4…20mA
Analog Outputs N/A N/A 2x 4…20mA
Real Time Clock Built in
Operating Voltage 18…30Vdc
Power Consumption 8W
RTC Battery CR2032 button cell lithium battery, 3V(removable)
RTC Battery Life 5 years
Operating Temperature 0…50°C
Storage Temperature -20…60°C
Operating Humidity 0…90%RH (non condensed)
Dimensions 278 x 200 x 50 mm
Panel Cut-out 265 x 186 mm
Weight 1300 g
3 Quick Start Guide EN PROOP 03 V04 01/24
Dimensions
PROOP 4’’ Series
PROOP 5’’ Series
4 Quick Start Guide EN PROOP 03 V04 01/24
PROOP 7’’ Series
PROOP 10’’ Series
5 Quick Start Guide EN PROOP 03 V04 01/24
Panel Mounting
1- Before mounting the device in your panel, make sure that the cutout is of the right size.
2- Check front panel gasket position.
3- Insert the device through the cut out.
4- Insert the mounting clamps to the holes of device
5- Screw up the fixing screws until the unit completely immobile within the panel.
6 Quick Start Guide EN PROOP 03 V04 01/24
Installation
Before beginning installation of this product, please read the instruction manual
and warnings below carefully.
A visual inspection of this product for possible damage occured during shipment is recommended before
installation. It is your responsibility to ensure that qualified mechanical and electrical technicians install this
product.
Do not use the unit in combustible or explosive gaseous atmospheres.
Do not expose the unit to direct sun rays or any other heat source.
Do not place the unit in the neighbourhood of magnetic equipment such as transformers, motors or
devices which generate interference (welding machines, etc.)
To reduce the effect of electrical noise on device, Low voltage line (especially sensor inputcable) wiring
must be separated from high current and voltage line.
During the equipment is putted in hole on the metal panel while mechanical installation some metal burrs
can cause injury on hands, you must be careful.
Montage of the product on a system must be done with it’s own fixing clamps.
Do not do the montage of the device with inappropriate fixing clamps. Be sure that device will not fall while
doing the montage.
If possible, use shielded cable and shield must be connected to ground only one side.
Keep the power off until all of the wiring is completed so that electric shock and trouble with the unit can
be prevented
The digital outputs and supply connections is designed to be isolated from each other.
Before commissioning the device, parameters must be set in accordance with desired use.
Incomplete or incorrect configuration can cause dangerous stiuations
The unit is normally supplied without a power switch or a fuse. Use power switch and fuse as required.
Be sure to use the rated power supply voltage to protect the unit against damage and to prevent failure.
After the device power on, check power LED lights from on the device screen.
If there is danger of serious accident resulting from a failure or defect in this unit, power off the system and
the electrical connection of the device from the system
Never attempt to disassemble, modify or repair this unit. Tampering with the unit may results in
malfunction, electric shock or fire.
Please contact us in case of an unexpected situation.
It is your responsibility if this equipment is used in a manner not specified in this instruction manual.
The users should use IPERTU IDE software to perform editing in PROOP's product.
7 Quick Start Guide EN PROOP 03 V04 01/24
IPERTU IDE Program Setup
Please, follow the steps on the below for installation the IPERTU IDE Software Program.
Step 1:
It is strongly recommended that before proceeding, you ensure that no other Windows programs are
running.
Step 2:
Run the setup.exe included in the installation package.
Step 3:
Continue the installation by following the dialog boxes on the screen and choose where to install.
Step 4:
After selecting the default folder, click “Next >” button . If necessary, you can retrieve individual steps with
“< Back” button. Program will automatically be installed in the default folder.
Step 5:
After installation, click “Finish” button in the dialog box on the screen and finish the operation.
Step 6:
Click the Windows Start > Programs > IPERTU IDE shortcut to start the application
8 Quick Start Guide EN PROOP 03 V04 01/24
Pin Connections
Supply (For PROOP 4,5,7 and 10) COM4 (For PROOP 7 and 10)
Terminal Terminal
+ 2- Rx
- 3- Tx
5- GND
7- RTS
8- CTS
COM1 (For PROOP 7) COM2 - COM3 (For PROOP 4 and 5)
Terminal Terminal
Rx+ A
Rx- B
Tx+ GND
Tx- Tx
Rx
COM2 - COM3 (For PROOP 7) COM3 (For PROOP 10)
Terminal Terminal
A Rx
B Tx
GND GND
Rx
Tx
GND
GND
COM1 - COM2 (PROOP 10 için)
Terminal
Rx+
Rx-
Tx+
Tx-
GND
GND
9 Quick Start Guide EN PROOP 03 V04 01/24
Digital Inputs/Outputs (For PROOP 7)
Terminal Definition Connecting Scheme
Digital Out
DO-
Supply -
DO4
DO3
Digital Outputs
DO2
DO1
Digital Outputs
DO+
Supply +
DI4
DI3
Digital Inputs
DI2
DI1
NPN / PNP Selection of
+/-
Digital Inputs
Analog/Digital Inputs (For PROOP 10)
Terminal Definition Connecting Scheme
A2-
Analog Input 2
A2+
A1+
Analog Input 1
A1-
DI5
DI4
Digital
DI3
Inputs
DI2
DI1
NPN / PNP Selection of
+/-
Digital Inputs
10 Quick Start Guide EN PROOP 03 V04 01/24
Analog/Digital Outputs (For PROOP 10)
Terminal Definition Connecting Scheme
Analog Output
AO+
Supply+
Analog Output
AO-
Supply-
AO2
Analog Outputs
AO1
DO- Digital Outputs Supply-
DO4
DO3
Digital Outputs
DO2
DO1
DO+ Digital Outputs Supply+
11 Quick Start Guide EN PROOP 03 V04 01/24
Warranty
This warranty is provided for a period of two years. This warranty is in force if duty and responsibilities
which are determined in warranty document and instruction manual performs by the customer completely.
Maintenance
Repairs should only be performed by trained and specialized personnel. Cut power to the device before
accessing internal parts.
Do not clean the case with hydrocarbon based solvents (Petrol, Trichlorethylene etc.). Use of these solvents
can reduce the mechanical reliability of the device.
Other Informations
Manufacturer Company Informations:
Emko Elektronik Sanayi ve Ticaret A.Ş.
Fethiye OSB Mah. Turkuaz Cd. No:15 NİLÜFER/BURSA
Phone : (224) 261 1900
Fax : (224) 261 1912
Company Information Providing Maintenance and Repair Services:
Emko Elektronik Sanayi ve Ticaret A.Ş.
Fethiye OSB Mah. Turkuaz Cd. No:15 NİLÜFER/BURSA
Phone : (224) 261 1900
Fax : (224) 261 1912
12 Quick Start Guide EN PROOP 03 V04 01/24
