BEng-9

CIVIL ENGINEERING

SYLLABUS

The syllabus applies to students admitted in the academic year 2013-14 and thereafter under the four-year
curriculum.

Definition and Terminology

Each course offered by the Department of Civil Engineering shall be classified as either introductory level
course or advanced level course.

A Discipline Core course is a compulsory course which a candidate must pass in the manner provided for
in the Regulations.

A Discipline Elective course refers to any technical course offered by the Department of Civil
Engineering for the fulfillment of the curriculum requirements of the degree of BEng in Civil Engineering
that are not classified as discipline core course.

Curriculum

The Curriculum comprises 240 credits of courses as follows:

General Engineering Courses

Students are required to complete at least 36 credits of General Engineering Course.

Discipline Core Courses

Students are required to complete ALL discipline core courses (78 credits), comprising 24 credits of
introductory core courses and 54 credits of advanced core courses.

Discipline Elective Courses

Students are required to complete at least 36 credits of advanced discipline elective courses offered by the
Department of Civil Engineering.

Elective Courses
Students are required to complete 18 credits of elective course(s) offered by either the Department of
Civil Engineering, or other departments within or outside of the Faculty of Engineering.

University Requirements
Students are required to complete:
a) 12 credits in English language enhancement, including 6 credits in “CAES1000 Core University
English” and 6 credits in “CAES9540 Technical English for Civil Engineering”;
b) 6 credits in Chinese language enhancement course “CENG9001 Practical Chinese for
Engineering Students”; and
c) 36 credits of courses in the Common Core Curriculum, selecting not more than one course from
the same Area of Inquiry within one academic year and at least one but no more than two courses
from each Area of Inquiry during the whole period of study.

Capstone Experience
Students are required to complete the 12-credit “CIVL4102 Final Year Project” to fulfill the capstone
experience requirement for the degree of BEng in Civil Engineering.
 BEng-10

Internship
Students are required to complete the 6-credit internship “CIVL2109 Internship”, which normally takes
place after their third year of study.

Degree Classification

The degree of Bachelor of Engineering shall be awarded in five divisions in accordance with EN16 of the
Regulations for the Degree of Bachelor of Engineering and UG9 of the Regulations for the First Degree
Curricula.

The details of the distribution of the above course categories are as follows:

The curriculum of BEng (Civil Engineering) comprises 240 credits of courses with the following
structure:

UG 5 Requirements (54 credits)

Course Code Course No. of credits

CAES1000 Core University English 6
CAES9540 Technical English for Civil Engineering 6
CENG9001 Practical Chinese for Engineering Students 6
CC##XXXX University Common Core Course (6 courses)* 36
Total for UG5 Requirements 54

* Students can select not more than one course from each Area of Inquiry within one academic year and
at least one and no more than two courses from each Area of Inquiry during the whole period of study.

Faculty General Engineering Courses (36 credits)

Course Code Course No. of credits

MATH1851 Calculus and ordinary differential equations 6
MATH1853 Linear algebra, probability & statistics 6
ENGG1111/ Computer programming and applications/ 6
ENGG1112 Computer programming and applications I
PHYS1050 Physics for engineering students 6
ENGG1201 Engineering for sustainable development 6
ENGG120# Any one of the General Engineering Courses offered by other 6
Departments of the Faculty of Engineering*
Total for Faculty General Engineering Courses 36

* Choose one General Engineering Course from the following list:

ENGG1202 Introduction to computer science

ENGG1203 Introduction to electrical and electronic engineering
ENGG1204 Industrial management and logistics
ENGG1205 Introduction to mechanical engineering
ENGG1206 Introduction to biomedical engineering
 BEng-11

Discipline Core Engineering Courses (78 credits)

Introductory Courses (24 credits)

Course Code Course No. of credits

CIVL1105 Environmental engineering 6
CIVL1113 Engineering mechanics & materials 6
CIVL1114 Surveying & drawing 6
MECH2407 Multivariable calculus & partial differential equations 6
Total for Introductory Discipline Core Engineering Courses 24

Advanced Courses (54 credits)

Course Code Course No. of credits

CIVL2102 Engineering geology and rock mechanics 6
CIVL2103 Fluid mechanics 6
CIVL2104 Hydraulics and hydrology 6
CIVL2105 Theory and design of structures I 6
CIVL2106 Soil mechanics 6
CIVL2107 Theory and design of structures II 6
CIVL2108 Principles of civil engineering management 6
CIVL2111 Transportation engineering 6
CIVL4101 Capstone design project 6
Total for Advanced Discipline Core Engineering Courses 54

Capstone Experience and Internship (18 credits)

Course Code Course No. of credits

CIVL4102 Final Year Project+ 12
CIVL2109 Internship* 6
Total for Capstone Experience and Internship Courses 18

+Capstone Experience
*Training

Discipline Elective Courses (36 credits)

Course Code Course No. of credits

CIVL2110 Experiential learning 6
CIVL3101 Advanced engineering mechanics 6
CIVL3103 Construction project management 6
CIVL3106 Engineering hydraulics 6
CIVL3107 Environmental impact assessment of civil engineering projects 6
CIVL3108 Foundation engineering 6
CIVL3111 Municipal and industrial wastewater treatment 6
CIVL3112 Prestressed concrete structures 6
CIVL3114 Slope engineering 6
CIVL3115 Solid and hazardous waste management 6
CIVL3116 Steel structures 6
 BEng-12

CIVL3118 Theory and design of structures III 6

CIVL3119 Traffic engineering 6
CIVL3120 Transportation infrastructure engineering 6
CIVL3121 Water resources engineering 6
CIVL3122 Wind engineering 6
CIVL3125 Law for civil engineers 6
CIVL3126 Engineering practice in Mainland China 6
CIVL3127 Building practice in the built environment 6
CIVL3128 Structural dynamics and earthquake engineering 6
CIVL3129 Numerical analysis in geotechnical engineering 6
CIVL3130 Structural fire engineering 6
CIVL3131 Earth retaining system 6
CIVL3132 Geotechnical testing instrumentation and monitoring 6
CIVL3133 Ground improvement 6
CIVL3134 Environmental geotechnology 6
Complete six disciplinary elective courses for a total of 36 credits 36

Elective Courses (18 credits)

At least 18 credits of courses offered by either the Department of Civil Engineering, or other departments
within or outside of the Faculty of Engineering.

Summary of curriculum structure of BEng (Civil Engineering)

Course Categories No. of credits

UG5 Requirements 54
General Engineering Courses 36
Discipline Core Engineering Courses (Introductory) 24
Discipline Core Engineering Courses (Advanced) 54
Capstone Experience and Internship 18
Discipline Elective Courses 36
Elective Courses 18
Total 240

The proposed syllabus by study year is as follows:

FIRST YEAR

General Engineering Courses (36 credits)

MATH1851 Calculus and ordinary differential equations
MATH1853 Linear algebra, probability & statistics
ENGG1111/ Computer programming and applications/
ENGG1112 Computer programming and applications I
PHYS1050 Physics for engineering students
ENGG1201 Engineering for sustainable development
ENGG120X Any one of the General Engineering Courses offered by other Departments of the
Faculty of Engineering
 BEng-13

University Requirements (UG5) (24 credits)

CAES1000 Core University English
CC##XXXX Three Common Core Courses

SECOND YEAR

Introductory Core Courses (24 credits)

CIVL1105 Environmental engineering
CIVL1113 Engineering mechanics & materials
CIVL1114 Surveying & drawing
MECH2407 Multivariable calculus & partial differential equations

Advanced Core Courses (18 credits)

CIVL2103 Fluid mechanics
CIVL2105 Theory and design of structures I
CIVL2106 Soil mechanics

University Requirements (UG5) (18 credits)

CC##XXXX Three Common Core Courses

THIRD YEAR

Advanced Core Courses (30 credits)

CIVL2102 Engineering geology and rock mechanics
CIVL2104 Hydraulics and hydrology
CIVL2107 Theory and design of structures II
CIVL2108 Principles of civil engineering management
CIVL2111 Transportation engineering

Internship (6 credits)
CIVL2109 Internship

University Requirements (UG5) (6 credits)

CENG9001 Practical Chinese for Engineering Students

Discipline Elective Courses (18 credits)

FOURTH YEAR

Advanced Core Courses (6 credits)

CIVL4101 Capstone design project

Discipline Elective Courses (18 credits)

Capstone Experience (12 credits)

CIVL4102 Final Year Project

University Requirements (UG5) (6 credits)

CAES9540 Technical English for Civil Engineering

Elective Courses (18 credits)

 BEng-14

COURSE DESCRIPTIONS

Candidates will be required to do the coursework in the respective courses selected. Not all courses are
offered every semester.

Faculty General Engineering Courses

ENGG1111 Computer programming (6 credits)

ENGG1112 Computer programming I (6 credits)
MATH1851 Calculus and ordinary differential equations (6 credits)
MATH1853 Linear algebra, probability & statistics (6 credits)
MECH2407 Multivariable calculus & partial differential equations (6 credits)
PHYS1050 Physics for engineering students (6 credits)
ENGG1201 Engineering for sustainable development (6 credits)
ENGG1202 Introduction of computer science (6 credits)
ENGG1203 Introduction to electrical and electronic engineering (6 credits)
ENGG1204 Industrial management and logistics (6 credits)
ENGG1205 Introduction to mechanical engineering (6 credits)
ENGG1206 Introduction to biomedical engineering (6 credits)

Please refer to the General Engineering Courses in the syllabus for the degree of BEng for details.

University Requirements on Language Enhancement Courses

CAES1000. Core University English (6 credits)

CENG9001. Practical Chinese for engineering students (6 credits)

Please refer to the University Language Enhancement Courses in the syllabus for the degree of BEng for
details.

CAES9540. Technical English for Civil Engineering (6 credits)

This one semester 6-credit English course will be offered to final year Civil Engineering students. It will
run alongside the Civil Engineering core course “Project”. The main course objective is to provide
students with training on report writing and oral presentation skills. Students will learn to write a
technical report in a professional and effective manner through drafting and revision of their work. They
will also be trained to give a technical presentation that focuses on explaining technical information to the
general audience, handling over in a group presentation and designing appropriate visual aids to both
professional and non-expert audiences. Assessment is by coursework and a final test.

Assessment: 100% continuous assessment.

 BEng-15

University Common Core Curriculum

36 credits of courses in the University Common Core Curriculum, in which students can select not more
than one course from the same Area of Inquiry within one academic year and at least one but no more
than two courses from each Area of Inquiry during the whole period of study:

 Scientific and Technology Literacy

 Humanities
 Global Issues
 China: Culture, State and Society

Introductory Discipline Core Engineering Courses

CIVL1105. Environmental engineering (6 credits)

This is an introductory course on environmental engineering. Students are taught in 31 hours of lecture
plus 8 hours of interactive problem-based tutorial (IPBT). The IPBT is designed to train students in small
groups for using the knowledge and engineering principles learned from the course to solve practical
environmental engineering related problems.

Assessment: 20% continuous assessment, 80% examination

CIVL1113. Engineering mechanics and materials (6 credits)

The Engineering Mechanics part of this course aims to provide students with a firm foundation of
engineering mechanics, which is needed for their later studies in structural engineering and geotechnical
engineering. This part covers equilibrium of forces; bending moment, shear and axial forces; beam theory
for bending and shear; shear centre; deflection of beams; analysis of stress and strain; and energy
methods.
The Materials part of this course aims to provide students with a general knowledge of common
construction materials and some background knowledge of material science. This part covers major
applications and required properties of construction materials; structural steel; concrete; masonry; timber;
bituminous materials; crystalline structure; elastic and plastic deformation; phase diagram; alloying;
material forming and heat treatment; and corrosion.
Assessment: 15% practical work, 15% continuous assessment, 70% examination

CIVL1114. Surveying and drawing (6 credits)

The Surveying part of this course aims to provide students with an overview on the surveying principles
in determination of the differences in levelling between stations and of the coordinates of stations.
Students will be introduced to basic surveying instruments and techniques through lectures and field
work. The aim of the Drawing part of this course is to familiarize the students with the techniques for
reading and production of both hand drawings and computer aided drafting (CAD) drawings. Students are
expected to understand and appreciate the importance of surveying and drawing in the construction
industry in order to prepare them for an engineering career.
Assessment: 35% practical work, 65% continuous assessment
 BEng-16

Advanced Discipline Core Engineering Courses

CIVL2102. Engineering geology and rock mechanics (6 credits)

This course provides an introduction to engineering geology, acquainting the students with the
fundamental aspects of rock mechanics, and developing the students’ capability of applying the concepts
and knowledge to solve practical problems in rock engineering.

Assessment: 20% practical work, 10% continuous assessment, 70% examination

CIVL2103. Fluid mechanics (6 credits)

The course introduces the fundamental concepts of fluid flow, and examples of engineering fluid
mechanics.

The course helps students to develop a sound understanding of control volume analysis, and its use with
mass, momentum, and energy conservation principles. The course prepares students for dimensional
analysis for the use of scale models in wind tunnel and hydraulic model testing.

Assessment: 15% practical work, 15% continuous assessment, 70% examination

CIVL2104. Hydraulics and hydrology (6 credits)

This course is to consolidate the principles of fluid mechanics learnt in CIVL2103, to apply them to civil
engineering hydraulic problems, and to provide an understanding of the basic concepts of the
hydrological cycle including its relevance and application to civil engineering field.

Pre-requisite: CIVL2103 Fluid mechanics

Assessment: 15% practical work, 15% continuous assessment; 70% examination

CIVL2105. Theory and design of structures I (6 credits)

This is the first of three consecutive courses on Theory and Design of Structures. This course provides
students with the basic knowledge in structural theory and design. Apart from introducing students to
statically determinate structures, it also provides the background for future study of statically
indeterminate structures.

Prerequisite: CIVL1113 Engineering mechanics and materials

Assessment: 15% practical work, 15% continuous assessment, 70% examination

CIVL2106. Soil mechanics (6 credits)

Soil mechanics is a branch of engineering mechanics that describes the behaviour of soils. It differs from
fluid mechanics and solid mechanics in the sense that soils consist of a heterogeneous mixture of fluids
(usually air and water) and particles (usually clay, silt, sand and gravel) but soil may also contain organic
 BEng-17

solids, liquids, and gasses and other matter. Along with rock mechanics, soil mechanics provides the
theoretical basis for analysis in geotechnical engineering. Soil mechanics is used to analyze the
deformations of and flow of fluids within natural and man-made structures that are supported on or made
of soil, or structures that are buried in soils. Examples applications are building and bridge foundations,
retaining walls, dams, and buried pipeline systems.

Assessment: 20% practical work, 20% continuous assessment, 60% examination

CIVL2107. Theory and design of structures II (6 credits)

This course is the second of three consecutive courses on Theory and Design of Structures. This course
aims to provide students with knowledge and understanding in behaviour, analysis and design of statically
indeterminate structures.

Prerequisite: CIVL2105 Theory and design of structures I

Assessment: 30% continuous assessment, 70% examination

CIVL2108. Principles of civil engineering management (6 credits)*

Civil engineering projects are characterised by their uniqueness, complexity and uncertainty, and these
have posed immense challenges to our industry. To satisfy the client and project requirements, a good
management skill and knowledge is of paramount importance. While engineers play a key role in relevant
government departments, client organisations, design offices and contracting firms, they have the
responsibilities of improving the efficiency, safety and quality of civil engineering projects and
maximising the chance of project success and discharging their duties ethically. Therefore, the aims of
this course are to introduce the basic concepts of various aspects of management and to explain how to
apply these management principles to plan, organise and control a civil engineering project.

Assessment: 30% continuous assessment, 70% examination

* For the double-degree in BEng/BBA, students who have completed the business course of ‘Principles of
management’ are exempted from taking this core course under the BEng curriculum.

CIVL2111. Transportation engineering (6 credits)

This course is an introductory course of Transportation Engineering, and covers the causes and
motivations of the movements of people and goods, the basic characteristics of different transportation
modes, land use and transportation planning, equilibrium analysis, cost-benefit analysis, travel demand
modeling and forecasting, highway alignment and geometric design, transportation surveys, and traffic
impact assessment. Hong Kong examples will be used if possible.

Assessment: 20% continuous assessment, 80% examination

 BEng-18

CIVL4101. Capstone Design Project (6 credits)

All modern engineering projects required substantial design and communication skills from engineers.
With the demand for quality infrastructural projects, many professional engineers are required to
participate in interdisciplinary teams throughout various project stages. Therefore, this course aims to
train future civil engineers to handle civil engineering projects through synergetic teamwork within a
multi-disciplinary working environment. The course will start by introducing the importance of
engineering design and communication skills, and then will equip students with the general knowledge of
project designing across different disciplines by a series of guest lectures. Student will be divided into
small project groups. Each group will be allocated a real-life project and supervised by one of the
departmental teaching staff (staff tutor) and an industrial tutor. The students will work closely with their
staff tutor and industrial tutor throughout the project period, together with the specific technical advisors,
to carry out feasibility study, preliminary design and detail design of their project. The project will be
assessed by a series of oral presentations and written reports from the project team.

Assessment: 100% continuous assessment

Capstone Experience and Internship

CIVL2109. Internship (6 credits)

The course is to provide industrial training to engineering students. The students will have an opportunity
to gain practical experience in civil engineering and related professions.

The course requires students to complete a period of full time approved internship in industry, of not less
than 4 weeks normally after the end of the second semester of the student’s third academic year of study.
The students are required to complete the internship to the satisfaction of an engineering professional,
who will act as the students’ supervisors during the internship.

During the course of their internship, sometimes students will be asked to visit construction sites. To
comply with the legal requirements and for safety reasons, all students must complete the Mandatory
Basic Safety Training Course (MBST). Through the MBST course, students will gain an understanding
on the relevant safety legislation; potential hazards and preventive strategies; use of the protective
equipment and the accident reporting mechanism.

Assessment: 100% continuous assessment

CIVL4102. Final Year Project (12 credits)

The primary aim of the project is to give each individual student an opportunity to handle a practical
engineering problem and to present the findings in a precise and concise report. An important part of the
project lies in the way in which the students plan and carry out the task, and apply their engineering
knowledge sensibly and diligently to solve the problem. The way in which the students present their
findings is equally important.

Assessment: 100% continuous assessment

 BEng-19

Discipline Elective Courses

CIVL2110 Experiential learning (6 credits)

To complete a period of training in industry, workshop training, study tour, or leadership programme,
approved by the Head of Department, not less than a total of four weeks during the summer semester,
subject to satisfactory performance in these activities and the submission of a satisfactory completion
report.

Assessment: 100% continuous assessment

CIVL3101. Advanced engineering mechanics (6 credits)

CIVL3101 Advanced Engineering Mechanics aims to introduce to the fundamentals of engineering

mechanics and how this is linked to engineering solutions by advanced computation techniques based on
the finite element method. Equilibrium in elasticity problems and continuity equation for steady-state
field problems are discussed, and by means of the virtual work principle, finite element formulation will
be systematically established. Using simple 3-node triangular element as an example, engineering
problems in structural mechanics and fluid flow are analysed. A computer demonstration will be
presented to show students how complex practical engineering problems are tackled, and allow them to
develop the ability to analyse realistic engineering problems by themselves and appreciate the capability
and limitations of modern computational tools for engineering solutions.

Assessment: 30% continuous assessment, 70% examination

CIVL3103. Construction project management (6 credits)

This course conveys knowledge of the fundamentals of construction project management, including core
principles and their basic applications, which can be further built upon during career development. Topics
span both the management of civil engineering designs and the management of construction projects. The
course imparts important basics of the planning and control of time and money, and links these to
achieving better value for stakeholders, including quality and life cycle considerations.

The course is designed to enable civil engineering undergraduates to appreciate and assimilate key
principles and good practices for the effective, efficient and ethical management of construction projects.
It also aims to equip young civil engineers with the basic knowledge that will enable them to perform well
and contribute meaningfully in multi-disciplinary project teams that may include financial and legal
professionals, apart from those from other core construction industry disciplines

Assessment: 30% continuous assessment, 70% examination

CIVL3106. Engineering hydraulics (6 credits)

The course Engineering Hydraulics covers three major parts: Open Channel Flow, Storm Drainage
Design and Environmental Hydraulics.

In Open Channel Flow, emphasis will be placed on the ‘gradually varied’ open channel flow (GVF),
which deals with the classification of GVF profiles and different methods of computation of flow profiles.
 BEng-20

Some examples of ‘rapidly varied’ flow, such as energy dissipators and vertical drop structures, will also
be given.

In Storm Drainage Design, the classification of drainage and sewerage systems will be introduced.
Students will learn the design of urban stormwater drainage system.

In Environmental Hydraulics, students will appreciate the assimilative capacity (self purification) of the
natural environment, through the study of basic concepts of turbulent mixing and dispersion of pollutants
in water. Examples will be given to demonstrate the use of advective diffusion equation to solve actual
environmental problems.

Prerequisite: CIVL2104 Hydraulics and hydrology

Assessment: 20% practical work, 20% continuous assessment, 60% examination

CIVL3107. Environmental impact assessment of civil engineering projects (6 credits)

This course will introduce concepts on environmental protection legislation, environmental impact
assessment process, environmental impacts during construction and operation of projects, mitigation
measures, modelling, environmental monitoring and audit, and case studies.

Prerequisite: CIVL1105 Environmental engineering and CIVL2103 Fluid mechanics

Assessment: 30% continuous assessment, 70% examination

CIVL3108. Foundation engineering (6 credits)

Foundation engineering deals with the investigation, design and construction of the foundations of
engineering structures, which is of prime importance. This course addresses the site investigation of a
geotechnical project, follows by the design and construction of shallow and deep foundations in
accordance with both ultimate and serviceability criteria. In particular the design and construction
practices in Hong Kong will be addressed. A site visit will be arranged to offer students an opportunity to
observe the construction practice in Hong Kong.

Prerequisite: CIVL2106 Soil mechanics

Assessment: 30% continuous assessment, 70% examination

CIVL3111. Municipal and industrial wastewater treatment (6 credits)

This course focuses on the theory, design and operation of wastewater treatment. Emphasis will be placed
upon a fundamental understanding of commonly used treatment technologies. Major sections of the
course cover the generation and characteristics of municipal wastewater, sewerage systems, preliminary
treatment, primary sedimentation, secondary biological treatment, nutrient removal, disinfection, sludge
treatment and disposal, unit process selection and treatment plant design, characteristics of industrial
wastewater, and physical, chemical and biological processes used in industrial wastewater treatment.

The course aims to introduce to students the basic concept of wastewater treatment engineering and the
knowledge of unit treatment operations and processes. At the end of this course, students who fulfill the
requirement of the course will be able to present the principles and theories behind the common
 BEng-21

wastewater treatment technologies and to conduct preliminary design of sewerage systems and typical
physical, chemical and biological units used in conventional wastewater treatment.

Prerequisite: CIVL1105 Environmental engineering and CIVL2103 Fluid mechanics

Assessment: 20% practical work, 80% examination

CIVL3112. Prestressed concrete structures (6 credits)

This is an elective course to provide students with the basic knowledge for the design of Prestressed
Concrete Structures. Apart from introducing students to the fundamental principles of prestressing and
application to design of long-span concrete structures, it also provides the background for future study of
bridge engineering. Each student is required to submit a comprehensive design of prestressed concrete
structure. Students must have taken the pre-requisite CIVL2107 Theory and Design of Structures II
before taking this course.

Prerequisite: CIVL2107 Theory and design of structures II

Assessment: 30% continuous assessment, 70% examination

CIVL3114. Slope engineering (6 credits)

This course is to provide our students with basic knowledge of slope stability analysis and design. It
covers slope stability analyses, cases of landslide hazards, landslide investigation, uncertainties in slope
stability analysis, landslip preventive measures and design, many case studies and actual examples, a
Slope/w software workshop and one field technical trip.

Prerequisite: CIVL2102 Engineering geology and rock mechanics and CIVL2106 Soil mechanics
Assessment: 20% continuous assessment, 80% examination

CIVL3115. Solid and hazardous waste management (6 credits)

Human activities generate solid waste materials that are often discarded because they are considered
useless. However, the disposal of these unwanted waste materials has created a heavy burden to our
environment and sometimes even threatened the human health due to its hazardous properties. Waste
management has become one of the most significant problems of our time because the current ways of
life in Hong Kong and in many areas of the world produce enormous amounts of waste, and most people
want to preserve their lifestyle, while also protecting the environment and public health. Furthermore, if
managed properly, many of these waste materials can be reused or recovered for becoming a resource for
industrial production or energy generation. This course is an introduction to the key managing concepts
and processing technologies of solid waste. It aims to train future engineers capable of conducting solid
waste project planning for industries, businesses, communities and governmental sectors. The discussion
of context will stem from solid waste materials generated from municipal sources, and then include
selected examples from industrial sources and/or of hazardous properties with local relevance. After the
training provided by this course, students are expected to be capable of using different planning tools to
manage the reduction of solid waste generation, the reuse and recovery of waste materials, or the safe and
economical disposal strategies.

Assessment: 30% continuous assessment, 70% examination

 BEng-22

CIVL3116. Steel structures (6 credits)

This course aims to provide students with knowledge and understanding in behaviour and design of steel
structures. Students will be exposed to plastic analysis, residual stress, slender sections, plate girders, steel
frames, connections and composite structures. Students must have fulfill the pre-requisite CIVL2107
Theory and Design of Structures II requirement before taking this course.

Prerequisite: CIVL2107 Theory and design of structures II

Assessment: 20% continuous assessment, 80% examination

CIVL3118. Theory and design of structures III (6 credits)

The theory part of the course introduces the theory and applications of the matrix method for static and
stability analyses of two-dimensional structures together with the elastic and plastic torsional analyses of
thin-walled sections. The design part of the course introduces the concept and principles of inelastic
design of reinforced concrete structures with emphasis on plastic hinge formation and moment
redistribution. On practical design aspects, ultimate limit state design as per Hong Kong Concrete Code
of special structural members such as two-way slabs, flat slabs, torsion members and slender columns will
be discussed and explained. The course also includes a section of serviceability limit state design of large
civil water-retaining reinforced concrete structures, such as underground box culverts, open channels,
manholes, inspection chambers and water/sewage treatment tanks.

Prerequisite: CIVL2107 Theory and design of structures II

Assessment: 30% continuous assessment, 70% examination

CIVL3119. Traffic engineering (6 credits)

This course is an introduction to the broad disciplines of traffic engineering and its applications to the
management and control of traffic flows in highways and the planning and design of highway junctions
and interchanges. This course covers the characteristics of traffic flow, mathematical models of traffic
flow, traffic management schemes, traffic surveys, traffic design for safety, and the planning and design
of different types of road junctions, including priority junctions, roundabouts, traffic signal controlled
junctions and grade-separated junctions and interchanges. Hong Kong examples will be used if possible.

Assessment: 30% continuous assessment, 70% examination

CIVL3120. Transportation infrastructure engineering (6 credits)

This course is an introduction to the theory and practice of transportation infrastructure planning, design
and maintenance. Emphasis is placed on facility operational requirements, facility location, demand
estimation, capacity assessment, properties of construction materials, design codes and their underlying
theories. The different stages of project development, including system planning, feasibility studies,
public consultation, project appraisal, detailed design and construction are discussed and illustrated by
case studies. Students are required to complete three exercises on infrastructure planning and design.
 BEng-23

Prerequisite: CIVL2111 Transportation engineering

Assessment: 30% continuous assessment, 70% examination

CIVL3121. Water resources engineering (6 credits)

CIVL3121 is a course that focuses on the concept, theory, design and operation of urban water supply
systems. Emphasis will be placed upon a fundamental understanding of commonly used water collection
and treatment technologies. Major sections of the course cover water cycle, water consumption and
demand, water collection, storage and transportation, drinking water quality, conventional surface water
treatment unit operations and processes, advanced water treatment technologies, water stabilisation and
corrosion control, urban water distribution and transmission, water reclamation and total water
management.

The course aims to introduce to students the basic concept of water resources engineering and the
knowledge of urban water supply. At the end of this course, students who fulfill the requirement of the
course will be able to present the principles and theories behind the common water collection and
treatment technologies and to conduct conceptual design of freshwater collection systems, common
surface water treatment processes and urban water distribution systems.

Prerequisite: CIVL1105 Environmental engineering and CIVL2103 Fluid mechanics

Assessment: 20% practical work, 80% examination

CIVL3122. Wind engineering (6 credits)

The course introduces the effects of wind on buildings, structures and the environment, with emphasis on
wind loading of buildings and structures.

The course provides students with the basic scientific knowledge of the engineering description of wind
and the engineering phenomena of wind flow around bluff bodies, buildings, bridges and civil
engineering structures. The basics of flow-structure interaction and wind-induced vibration of structures
are also presented. The course then continues to describe the format and features of a wind loading code
and how the code should be interpreted with the knowledge of wind engineering. The course also
introduces the effects of wind on pedestrian comfort and pollutant dispersion.

Assessment: 15% practical work, 15% continuous assessment, 70% examination

CIVL3125. Law for civil engineers (6 credits)

With the changing demands and expectations of civil engineers, law has become an essential part of the
body of knowledge important to the discharge of daily tasks of civil engineers. Whether working for sub-
contractors, contractors, consultants, governments or private developers, a core competence for the
planning, design, construction and maintenance of projects is the ability to apply principles of laws to
their works. These enable the proper management of projects and the areas of disputes arising thereunder.

This course aims at introducing the basic principles of laws with particular emphasis on those, which are
relevant to the construction industry.
 BEng-24

Assessment: 30% continuous assessment, 70% examination

CIVL3126. Engineering practice in Mainland China (6 credits)

To enable students to gain basic understanding of engineering design and construction practice in
Mainland China. By introducing some commonly used codes of practice, work procedures, quality
control system, engineering requirements, practical design case study, design principles and procedure of
foundation, building structures with and without seismic design requirement and bridges/highway
structures, students will be better equipped to engage in Mainland engineering projects. At the end of this
course, students should be able to understand the work procedure in Mainland China. In design, students
should be capable of carrying out correct design of foundations and buildings as per various GB Codes
and understand the principle of respective design clauses stipulated in the Codes.

Prerequisite: CIVL2107 Theory and design of structures II

Assessment: 30% continuous assessment, 70% examination

CIVL3127. Professional practice in the built environment (6 credits)

Building construction is one of the major sectors of the construction industry in Hong Kong. Many high-
rise buildings were built in the last three decades, calling for sophisticated designs in building layout,
structure and foundation. At the same time it demands high technique in construction skill and
management. There are government departments ensuring compliance with statutory standards of safety,
health and environment of buildings and building works. Civil engineers would join relevant government
departments, client organizations, consultant and contracting firms playing a key role in planning, design
and construction of buildings. Therefore, the aims of this course are to introduce the basic knowledge and
idea of statutory control on building planning, construction and site supervision.
Assessment: 30% continuous assessment, 70% examination

CIVL3128. Structural dynamics and earthquake engineering (6 credits)

Earthquake disaster is increasingly of global concern as it threatens the world’s population, economy, and
sustainable development. It is the responsibility of civil engineers to design and build earthquake-resistant
structures, in order to minimize the earthquake risk. By reducing losses of lives and properties, socio-
economical sustainability can be achieved.
In this course, students will be introduced to the basic science of earthquakes and its effects on the natural
and built environment.
Prerequisite: CIVL2107 Theory and design of structures II
Assessment: 30% continuous assessment, 70% examination

CIVL3129. Numerical analysis in geotechnical engineering (6 credits)

Advances in computer technology greatly enhance the application of numerical methods in geotechnical
engineering. The importance of numerical modelling in geotechnical practice has been increased
tremendously over the past decade. In this course, the students will be introduced a proper understanding
of the subject, covering from fundamentals of the numerical techniques to geotechnical practical
considerations. This course first provides students a basic knowledge of numerical techniques including
 BEng-25

the finite difference and finite element method. The second part of the course focuses on practical
considerations required for applying these techniques to geotechnical problems. It will be concluded by a
number of geotechnical applications and case histories.

Prerequisite: CIVL2106 Soil mechanics

Assessment: 35% continuous assessment, 65% examination

CIVL3130. Structural fire engineering (6 credits)

The major aims of this course are to introduce to the students the concept of fire safety engineering and
design of fire resistant structures. Students will be given opportunities to learn Eurocode for the design of
steel and concrete structures under elevated temperature. At the end of this course, students will be able
to understand the fire development and predict gas temperature of fire compartment and temperature of
structural members in fire condition. With respect to structural design, students will appreciate the
special structural actions that occur under elevated temperature and capable of carrying out fire resistance
design of simple steel and reinforced concrete members.

Prerequisite: CIVL2107 Theory and design of structures II

Assessment: 30% continuous assessment, 70% examination

CIVL3131. Earth retaining system (6 credits)

Development in urban areas is often limited by the space available, and efficient use of that space requires
building underground or near slopes. Earth retaining systems are the engineering solution to this problem.
This course introduces civil engineering students to different types of earth retaining systems, and gives
them the means of designing earth retaining walls from first principles. At the end of the course, the
students will have a good understanding of the forces exerted by the ground on retaining structures, for
different cases (e.g. inclined ground, inclined wall, embedded wall, wall friction/adhesion), the different
stabilizing methods that can be used (e.g. anchors, nails), and be able to use these calculations to design
safe retaining walls.

Pre-requisite: CIVL2106 Soil mechancis

Assessment: 30% continuous assessment, 70% examination

CIVL3132. Geotechnical testing, instrumentation and monitoring (6 credits)

Geotechnical testing aims at understanding the behaviour of geomaterials that engineers are dealing with.
A proper instrumentation and monitoring scheme provides crucial information for engineers to judge the
effectiveness and safety of the engineering design and construction. This course first provides students
advanced knowledge on geotechnical testing from both experimental and theoretical perspectives.
Students are required to have hands-on experience on a common geotechnical test – multi-stage triaxial
test. Then both practical and theoretical aspects of geotechnical instrumentation and monitoring are
addressed.

Prerequisite: CIVL2106 Soil mechanics

Assessment: 15% practical work, 15% continuous assessment, 70% examination
 BEng-26

CIVL3133. Ground improvement (6 credits)

Construction is sometimes needed in ground that has poor strength and stiffness qualities. Improving the
ground by reinforcing it or by modifying it can prevent excessive deformations or even failure. This
course introduces civil engineering students to ground improvement by modification or reinforcement. At
the end of the course, the students will have a good understanding of the different techniques used for
ground improvement, and be able to use some of the theory for design.

Prerequisite: CIVL2106 Soil mechanics

Assessment: 30% continuous assessment, 70% examination

CIVL3134. Environmental Geotechnology (6 credits)

Environmental geotechnology can be defined as an interdisciplinary science which covers soil and rock
and their interactions with various environmental cycles, including the atmosphere, biosphere,
hydrosphere, and lithosphere, as well as the geo-microbiosphere, and human activities, which includes
characteristics of tree and vegetation roots and bacterial activities in the subsurface and subsequent
response to the engineering behavior of the soil-water system.

The objective of the course is to provide the students with exposure to the geotechnical nature of
environmental problems through discussions of contaminant transport in porous media and relationship
with remediation technologies for hazardous waste sites and discussions of soil properties relative to
waste containment systems, soil stability, and permeability. At the end of the course, the students who
fulfill the requirements of this course should be able to understand the importance of Geotechnical
Engineering related to environmental issues, to perform preliminary designs of different components of a
municipal landfill, and to select appropriate remediation technologies for a contaminated site of a given
contaminated site.

Prerequisite: CIVL2106 Soil mechanics

Assessment: 30% continuous assessment, 70% examination
 BEng-27

Minor in Environmental Engineering

Candidates are required to complete a total of 48 credits of courses comprising:

(a) Introductory Courses (18 credits)

Course Code Course No. of credits

ENGG1201 Engineering for sustainable development* 6
CIVL1105 Environmental engineering 6
CIVL2103 Fluid mechanics OR 6
CIME2101 Water and air quality: concepts and measurement 6
Total for Introductory Discipline Core Engineering Courses 18

* Students opting for the Minor cannot use the course ENGG1201 Engineering for sustainable
development as satisfying the requirements of the General Engineering Course.

(b) Discipline Elective Courses (30 credits)

Students must complete 30 credits of discipline elective courses to be chosen from the following list:

Course Code Course No. of credits

CIME2101 Water and air quality: concepts and measurement 6
CIVL2111 Transportation engineering 6
CIVL2104 Hydraulics and hydrology 6
CIVL3106 Engineering hydraulics 6
CIVL3107 Environmental impact assessment of civil engineering projects 6
CIVL3111 Municipal and industrial wastewater treatment 6
CIVL3115 Solid and hazardous waste management 6
CIVL3121 Water resources engineering 6
CIVL3122 Wind engineering 6
CIVL3134 Environmental Geotechnology 6
MECH3420 Air pollution control 6
Total for Discipline Elective Courses 30

COURSE DESCRIPTIONS

For course descriptions, please refer to the syllabuses of the Civil Engineering programme.
 BEng-28

Minor in Geotechnical Engineering

Candidates are required to complete a total of 48 credits of courses comprising:

(a) Introductory Courses (18 credits)

Course Code Course No. of credits

MATH1851 Calculus and ordinary differential equations 6
MATH1853 Linear algebra, probability & statistics 6
CIVL2106 Soil mechanics 6
Total for Introductory Discipline Core Engineering Courses 18

(b) Discipline Elective Courses (30 credits)

Students must complete 30 credits of discipline elective courses to be chosen from the following list:

Course Code Course No. of credits

CIVL2102 Engineering geology and rock mechanics 6
CIVL3108 Foundation engineering 6
CIVL3114 Slope engineering 6
CIVL3129 Numerical analysis in geotechnical engineering 6
CIVL3131 Earth retaining system 6
CIVL3132 Geotechnical testing, instrumentation and monitoring 6
CIVL3133 Ground improvement 6
CIVL3134 Environmental geotechnology 6
Total for Discipline Elective Courses 30

COURSE DESCRIPTIONS

For course descriptions, please refer to the syllabuses of the Civil Engineering programme.
 BEng-29

CIVIL ENGINEERING (Environmental Engineering)

SYLLABUS

The syllabus applies to students admitted in the academic year 2013-14 and thereafter under the four-year
curriculum.

Definition and Terminology

Each course offered by the Department of Civil Engineering shall be classified as either introductory level
course or advanced level course.

A Discipline Core course is a compulsory course which a candidate must pass in the manner provided for
in the Regulations.

A Disciplinary Elective course refers to any technical course offered by the Department of Civil
Engineering for the fulfillment of the curriculum requirements of the degree of BEng in Civil
Engineering-Environmental Engineering that are not classified as discipline core course.

Curriculum

The Curriculum comprises 240 credits of courses as follows:

General Engineering Courses

Students are required to complete at least 36 credits of General Engineering Course.

Discipline Core Courses

Students are required to complete ALL discipline core courses (84 credits), comprising 24 credits of
introductory core courses and 60 credits of advanced core courses.

Disciplinary Elective Courses

Students are required to complete at least 36 credits of advanced disciplinary elective courses offered by
the Department of Civil Engineering.

Elective Courses
Students are required to complete 12 credits of elective course(s) offered by either the Department of
Civil Engineering, or other departments within or outside of the Faculty of Engineering.

University Requirements
Students are required to complete:
a) 12 credits in English language enhancement, including 6 credits in “CAES1000 Core University
English” and 6 credits in “CAES9540 Technical English for Civil Engineering”;
b) 6 credits in Chinese language enhancement course “CENG9001 Practical Chinese for
Engineering Students”; and
c) 36 credits of courses in the Common Core Curriculum, selecting not more than one course from
the same Area of Inquiry within one academic year and at least one and no more than two courses
from each Area of Inquiry during the whole period of study.

Capstone Experience
Students are required to complete the 12-credit “CIVL4102 Final Year Project” to fulfill the capstone
experience requirement for the degree of BEng in Civil Engineering-Environmental Engineering.
 BEng-30

Internship
Students are required to complete the 6-credit internship “CIVL2109 Internship”, which normally takes
place after their third year of study.

Degree Classification

The degree of Bachelor of Engineering shall be awarded in five divisions in accordance with EN16 of the
Regulations for the Degree of Bachelor of Engineering and UG9 of the Regulations for the First Degree
Curricula.

The details of the distribution of the above course categories are as follows:

The curriculum of BEng (Civil Engineering-Environmental Engineering) comprises 240 credits of

courses with the following structure:

UG 5 Requirements (54 credits)

Course Code Course No. of credits

CAES1000 Core University English 6
CAES9540 Technical English for Civil Engineering 6
CENG9001 Practical Chinese for Engineering Students 6
CC##XXXX University Common Core Course (6 courses)* 36
Total for UG5 Requirements 54
* Students can select not more than one course from each Area of Inquiry within one academic year and
at least one and no more than two courses from each Area of Inquiry during the whole period of study.

Faculty General Engineering Courses (36 credits)

Course Code Course No. of credits

MATH1851 Calculus and ordinary differential equations 6
MATH1853 Linear algebra, probability & statistics 6
ENGG1111/ Computer programming and applications/ 6
ENGG1112 Computer programming and applications I
PHYS1050 Physics for engineering students 6
ENGG1201 Engineering for sustainable development 6
ENGG120X Any one of the General Engineering Courses offered by other 6
Departments of the Faculty of Engineering*
Total for Faculty General Engineering Courses 36

*Choose one General Engineering Course from the following list:

ENGG1202 Introduction of computer science

ENGG1203 Introduction to electrical and electronic engineering
ENGG1204 Industrial management and logistics
ENGG1205 Introduction to mechanical engineering
ENGG1206 Introduction to biomedical engineering

Discipline Core Engineering Courses (84 credits)

 BEng-31

Introductory Courses (24 credits)

Course Code Course No. of credits

CIVL1105 Environmental engineering 6
CIVL1113 Engineering mechanics & materials 6
CIVL1114 Surveying & drawing 6
MECH2407 Multivariable calculus & partial differential equations 6
Total for Introductory Discipline Core Engineering Courses 24

Advanced Courses (60 credits)

Course Code Course No. of credits

CIME2101 Water and air quality: concepts and measurement 6
CIVL2102 Engineering geology and rock mechanics 6
CIVL2103 Fluid mechanics 6
CIVL2104 Hydraulics and hydrology 6
CIVL2105 Theory and design of structures I 6
CIVL2106 Soil mechanics 6
CIVL2107 Theory and design of structures II 6
CIVL2108 Principles of civil engineering management 6
CIVL2111 Transportation engineering 6
CIVL4101 Capstone design project 6
Total for Advanced Discipline Core Engineering Courses 60

Capstone Experience and Internship (18 credits)

Course Code Course No. of credits

CIVL4102 Final Year Project+ 12
CIVL2109 Internship* 6
Total for Capstone Experience and Internship 18

+Capstone Experience
*Training

Disciplinary Elective Courses (36 credits)

Course Code Course No. of credits

CIVL2110 Experiential learning 6
CIVL3103 Construction project management 6
CIVL3106 Engineering hydraulics 6
CIVL3107 Environmental impact assessment of civil engineering projects 6
CIVL3108 Foundation engineering 6
CIVL3111 Municipal and industrial wastewater treatment 6
CIVL3115 Solid and hazardous waste management 6
CIVL3118 Theory and design of structures III 6
CIVL3121 Water resources engineering 6
CIVL3122 Wind engineering 6
Complete six disciplinary elective courses for a total of 36 credits 36
 BEng-32

Elective Courses (12 credits)

At least 12 credits of courses offered by either the Department of Civil Engineering, or other departments
within or outside of the Faculty of Engineering.

Course Code Course No. of credits

CIVL3101 Advanced engineering mechanics 6
CIVL3112 Prestressed concrete structures 6
CIVL3114 Slope engineering 6
CIVL3116 Steel structures 6
CIVL3118 Theory and design of structures III 6
CIVL3119 Traffic engineering 6
CIVL3120 Transportation infrastructure engineering 6
CIVL3125 Law for civil engineers 6
CIVL3126 Engineering practice in Mainland China 6
CIVL3127 Building practice in the built environment 6
CIVL3128 Structural dynamics and earthquake engineering 6
CIVL3129 Numerical analysis in geotechnical engineering 6
CIVL3130 Structural fire engineering 6
CIVL3131 Earth retaining systems 6
CIVL3132 Geotechnical testing instrumentation and monitoring 6
CIVL3133 Ground improvement 6
CIVL3134 Environmental geotechnology 6

Summary of curriculum structure of BEng (Civil Engineering-Environmental Engineering)

Course Categories No. of credits

UG5 Requirements 54
General Engineering Courses 36
Discipline Core Engineering Courses (Introductory) 24
Discipline Core Engineering Courses (Advanced) 60
Capstone Experience and Internship 18
Disciplinary Elective Courses 36
Elective Courses 12
Total 240

The proposed syllabus by study year is as follows:

FIRST YEAR

General Engineering Courses (36 credits)

MATH1851 Calculus and ordinary differential equations
MATH1853 Linear algebra, probability & statistics
ENGG1111/ Computer programming and applications/
ENGG1112 Computer programming and applications I
PHYS1050 Physics for engineering students
ENGG1201 Engineering for sustainable development
ENGG120X Any one of the General Engineering Courses offered by other Departments of the
Faculty of Engineering
 BEng-33

University Requirements (UG5) (24 credits)

CAES1000 Core University English
CC##XXXX Three Common Core Courses

SECOND YEAR

Introductory Core Courses (24 credits)

CIVL1105 Environmental engineering
CIVL1113 Engineering mechanics & materials
CIVL1114 Surveying & drawing
MECH2407 Multivariable calculus & partial differential equations

Advanced Core Courses (18 credits)

CIVL2103 Fluid mechanics
CIVL2105 Theory and design of structures I
CIVL2106 Soil mechanics

University Requirements (UG5) (18 credits)

CC##XXXX Three Common Core Courses

THIRD YEAR

Advanced Core Courses (36 credits)

CIME2101 Water and air quality: concepts and measurement
CIVL2102 Engineering geology and rock mechanics
CIVL2104 Hydraulics and hydrology
CIVL2107 Theory and design of structures II
CIVL2108 Principles of civil engineering management
CIVL2111 Transportation engineering

Internship (6 credits)
CIVL2109 Internship

University Requirements (UG5) (6 credits)

CENG9001 Practical Chinese for Engineering Students

Disciplinary Elective Courses (12 credits)

FOURTH YEAR

Advanced Core Courses (6 credits)

CIVL4101 Capstone design project

Disciplinary Elective Courses (24 credits)

Capstone Experience (12 credits)

CIVL4102 Final Year Project

University Requirements (UG5) (6 credits)

CAES9540 Technical English for Civil Engineering
 BEng-34

Elective Courses (12 credits)

COURSE DESCRIPTIONS

Candidates will be required to do the coursework in the respective courses selected. Not all courses are
offered every semester.

Faculty General Engineering Courses

ENGG1111 Computer programming (6 credits)

ENGG1112 Computer programming I (6 credits)
MATH1851 Calculus and ordinary differential equations (6 credits)
MATH1853 Linear algebra, probability & statistics (6 credits)
MECH2407 Multivariable calculus & partial differential equations
PHYS1050 Physics for engineering students (6 credits)
ENGG1201 Engineering for sustainable development (6 credits)
ENGG1202 Foundation of computer science (6 credits)
ENGG1203 Introduction to electrical and electronic engineering (6 credits)
ENGG1204 Industrial management and logistics (6 credits)
ENGG1205 Introduction to mechanical engineering (6 credits)
ENGG1206 Introduction to biomedical engineering (6 credits)

Please refer to the General Engineering Courses in the syllabus for the degree of BEng for details.

University Requirements on Language Enhancement Courses

CAES1000. Core University English (6 credits)

CENG9001. Practical Chinese for Engineering Students (6 credits)

Please refer to the University Language Enhancement Courses in the syllabus for the degree of BEng for
details.

CAES9540. Technical English for Civil Engineering (6 credits)

This one semester 6-credit English course will be offered to final year Civil Engineering students. It will
run alongside the Civil Engineering core course “Project”. The main course objective is to provide
students with training on report writing and oral presentation skills. Students will learn to write a
technical report in a professional and effective manner through drafting and revision of their work. They
will also be trained to give a technical presentation that focuses on explaining technical information to the
general audience, handling over in a group presentation and designing appropriate visual aids to both
professional and non-expert audiences. Assessment is by coursework and a final test.

Assessment: 100% continuous assessment

 BEng-35

University Common Core Curriculum

36 credits of courses in the University Common Core Curriculum, in which students can select not more
than one course from the same Area of Inquiry within one academic year and at least one and no more
than two courses from each Area of Inquiry during the whole period of study:

 Scientific and Technology Literacy

 Humanities
 Global Issues
 China: Culture, State and Society

Introductory Discipline Core Engineering Courses

CIVL1105. Environmental engineering (6 credits)

CIVL1113. Engineering mechanics and materials (6 credits)
CIVL1114. Surveying and drawing (6 credits)

For course descriptions, please refer to the syllabuses of the Civil Engineering programme.

Advanced Discipline Core Engineering Courses

CIVL2102. Engineering geology and rock mechanics (6 credits)
CIVL2103. Fluid mechanics (6 credits)
CIVL2104. Hydraulics and hydrology (6 credits)
CIVL2105. Theory and design of structures I (6 credits)
CIVL2106. Soil mechanics (6 credits)
CIVL2107. Theory and design of structures II (6 credits)
CIVL2108. Principles of civil engineering management (6 credits)
CIVL2111. Transportation engineering (6 credits)
CIVL4101. Capstone Design Project (6 credits)
For course descriptions, please refer to the syllabuses of the Civil Engineering programme.

CIME2101. Water and air quality: concepts and measurement (6 credits)

This course will introduce concepts on water/air quality and pollution, the standard methods of water and
wastewater examination, air pollution control principles, and measurement techniques for common air
pollutants.
Prerequisite: CIVL1105 Environmental engineering
Assessment: 10% practical work, 10% continuous assessment, 80% examination

Capstone Experience and Internship

CIVL2109. Internship (6 credits)
CIVL4102. Final Year Project (12 credits)
For course descriptions, please refer to the syllabuses of the Civil Engineering programme.
 BEng-36

Disciplinary Elective Courses

CIVL2110. Experiential learning (6 credits)

CIVL3103. Construction project management (6 credits)
CIVL3106. Engineering hydraulics (6 credits)
CIVL3107. Environmental impact assessment of civil engineering projects (6 credits)
CIVL3108. Foundation engineering (6 credits)
CIVL3111. Municipal and industrial wastewater treatment (6 credits)
CIVL3115. Solid and hazardous waste management (6 credits)
CIVL3118. Theory and design of structures III (6 credits)
CIVL3121. Water resources engineering (6 credits)
CIVL3122. Wind engineering (6 credits)

For course descriptions, please refer to the syllabuses of the Civil Engineering programme.

Minor in Environmental Engineering

Candidates are required to complete a total of 48 credits of courses comprising:

(a) Introductory Courses (18 credits)

Course Code Course No. of credits

ENGG1201 Engineering for sustainable development* 6
CIVL1105 Environmental engineering 6
CIVL2103 Fluid mechanics OR 6
CIME2101 Water and air quality: concepts and measurement 6
Total for Introductory Discipline Core Engineering Courses 18

* Students opting for the Minor cannot use the course ENGG1201 Engineering for sustainable
development as satisfying the requirements of the General Engineering Course.

(b) Discipline Elective Courses (30 credits)

Students must complete 30 credits of discipline elective courses to be chosen from the following list:

Course Code Course No. of credits

CIME2101 Water and air quality: concepts and measurement 6
CIVL2111 Transportation engineering 6
CIVL2104 Hydraulics and hydrology 6
CIVL3106 Engineering hydraulics 6
CIVL3107 Environmental impact assessment of civil engineering projects 6
CIVL3111 Municipal and industrial wastewater treatment 6
CIVL3115 Solid and hazardous waste management 6
CIVL3121 Water resources engineering 6
CIVL3122 Wind engineering 6
CIVL3134 Environmental Geotechnology 6
MECH3420 Air pollution control 6
Total for Discipline Elective Courses 30
 BEng-37

COURSE DESCRIPTIONS

For course descriptions, please refer to the syllabuses of the Civil Engineering programme.

Minor in Geotechnical Engineering

Candidates are required to complete a total of 48 credits of courses comprising:

(a) Introductory courses (18 credits)

Course Code Course No. of credits

MATH1851 Calculus and ordinary differential equations 6
MATH1853 Linear algebra, probability & statistics 6
CIVL2106 Soil mechanics 6
Total for Introductory Discipline Core Engineering Courses 18

(b) Discipline Elective Courses (30 credits)

Students must complete 30 credits of discipline elective courses to be chosen from the following list:

Course Code Course No. of credits

CIVL2102 Engineering geology and rock mechanics 6
CIVL3108 Foundation engineering 6
CIVL3114 Slope engineering 6
CIVL3129 Numerical analysis in geotechnical engineering 6
CIVL3131 Earth retaining system 6
CIVL3132 Geotechnical testing, instrumentation and monitoring 6
CIVL3133 Ground improvement 6
CIVL3134 Environmental geotechnology 6
Total for Discipline Elective Courses 30

COURSE DESCRIPTIONS

For course descriptions, please refer to the syllabuses of the Civil Engineering programme.