360 Panoramic Assist System
Content
1. Product Introduction ............................................................................2
2. Installation Requirements .................................................................... 3
2.1 Main accessories of products ....................................................... 4
2.2 Product parameters ..................................................................... 4
2.3 Display screen when turning to reverse and driving normally ...... 5
3. Function Description ............................................................................7
3.1 Video Management ......................................................................7
3.2 Control settings ............................................................................ 8
3.3 Output display ............................................................................10
3.4 Stitching debugging ....................................................................12
3.5 Storage Management .................................................................19
3.6 System maintenance .................................................................. 20
Common troubleshooting methods ....................................................... 20
Disclaimer .............................................................................................. 20
360 Panoramic Assist System Manual
Thank you for choosing our 360 Panoramic Assist System. In order to use this machine
correctly, please read the manual carefully before using it. We will wholeheartedly provide you
with better products and services!
1. Product Introduction
This product is an advanced assisted driving system that integrates panoramic (360°
front, rear, left, right, and no blind zone) driving records (video), starting, reversing,
and parking surrounding image environment observation. When the vehicle is
moving forward or reversing, the driver can not only observe the blind spots through
the front and rear view cameras, but also see the real-time conditions in the front,
rear, left, and right directions on the panoramic image, so as to avoid causing damage
to children and small animals in the blind spots of the front and rear of the car or
scratching the car. When parking in place, because you can observe real-time images
in all directions, front, rear, left, and right, plus a reversing parking line prompt, you
can grasp the distance between cars and obstacles in time, so as to avoid bumping
into other vehicles and obstacles. During the driving process, this product performs
real-time video recording, so whether you encounter accidental scratches or
intentional "touching porcelain blackmail" can be used as your own strong evidence
to divide the responsibility well.
When encountering complex road conditions, narrow roads, heavy traffic, and many
vehicles, the real-time images around the vehicle can be viewed in real time, which
enhance the driving safety .
1.1 Steps to turn on and off the product
Automatic switch machine
*The power cord is powered by ACC, and the camera will automatically turn on and
start recording about 10 seconds after the car is started; when the car is turned off,
the device will automatically save the current video and turn off automatically.
*The power cable is powered by Battery, and the camera will automatically perform
a video recording cycle after the car is started and turned off.
2. Installation Requirements
1. Before installation, make sure whether the reversing video access port and video
control line of the installed car monitor are available, and then start the installation.
Video control line also can be called reversing detection line, signal control line,
panoramic control line, etc. The purpose of the video control line is to switch the
monitor to the video state. Some monitors do not have a reversing control line, but it
can also be installed with video priority input. If the display or car DVD is controlled
by the bus/main line, it can only be reversed and automatically ejected, and other
functions are realized through AV input or AUX.
2. Find a spacious place when installing.
3. Do not operate under strong light when adjusting, as reflections will affect the
calibration effect.
4. The following tools and items need to be prepared before installation:
①Screwdriver and other tools for disassembling the screws on the car.
②Modification tool for removing and installing the car interior.
③Automotive electric pen, insulating tape, multimeter and other tools.
④ 1.6m*2 or 1.2m*4 ancient checkerboard calibration cloth.
2.1 Main accessories of products
Name Quantity Picture Name Quantity Picture
Host 1 Camera 4
Remote Power
1
control cable 1
Camera
Remote extension
1 4
control cable
receiver
2.2 Product parameters
Name Parameters Name Parameters
12-24V
Language Chinese, English Working voltage (Over automatic
power-off
protection)
Signal system ≦500mA
PAL,NTSC optional Working current
Image format H.264 Working -30- 80℃
temperature
2-32GB 9-16V
Storage (The U disk is Trigger voltage
cycle-covered and
saved.)
Output Single composite 10 seconds
signal video output Cold start time
Software upgrading Support USB
Input signal 4 video inputs automatic upgrade
Attention: HD camera working voltage is 5V.
2.3 Display screen when turning to reverse and driving normally
Display screen when normal driving↑ Display screen when reversing↑
Display screen when turning right↑ Display screen when turning left↑
2.4 Instruction for camera installation position
Cameras applicable for front, rear and side view, no direction requirements. Lens
view downwards. The triangle icon on the lens should be in the middle of the camera
case that the image displayed uprightly. Image direction can be adjusted when
calibrate the images. Camera installation position is as shown below.
Side cameras installed at the one third (from cabin to the back) of the vehicle body.
Both side cameras must be at the same height and stay in the same position on each
side, can't be installed at the side mirrors.
Installation position for rear camera refers to car model. It supposed to be installed in
a high and upright position.
rear camera
3. Function Description
3.1 Video Management
1. Video list: You can select the box in front of the playlist separately
2. Play: Select the video file to be played back, press Play to watch the video, press
the arrow keys Up, Down,Left, and Right to play the front, back, left, and right videos
separately, and press the confirmation key to return to the four video screens to play
at the same time.
3. Delete: Select the video file to be deleted, press “Delete” to delete the file.
4. Lock: Select the video file to be locked, and press “Lock” to lock the file.
5. Unlock: Select the video file that needs to be unlocked, and press “Unlock” to
unlock the file.
3.2 Control settings
1) Time configuration
It is used to change the system recording time. After the installation is complete, the
system time must be set, otherwise the system recording time will be inaccurate,
resulting in inaccurate recording and evidence collection time. Press the arrow keys
Left and Right to move, and press the arrow keys Up and Down to change.
2) System language
Select the system language, and press the arrow keys Up and Down to change.
3) Driving track
3.1) Parking line
Set the parking line to be a dynamic track or normal parking line, and press the arrow
keys Up and Down to change.
3.2) Type
Select the trajectory type, corresponding to the corresponding vehicle model, and
press the arrow keys Up and Down to change.
3.3) Trajectories
Set the forward or reverse direction of the dynamic trajectory, and press the arrow
keys Up and Down to change.
3.4) Trigger
The trigger type can be set, and press the arrow keys Up and Down to change.
4) Time display
Set whether to display the time on the main image interface,and press the arrow
keys Up and Down to change.
5) Protection voltage
After the parking monitoring function is enabled, you can set the value of the system
voltage below which the system can automatically shut down, so as not to run out of
the car battery, and press the arrow keys Left and Right to move.
6) Vehicle model settings
This page is used to set the color of the vehicle model. In the first line, select the
vehicle model you want to change the color of. The lower part is the color of the car
model that can be selected. After selection, you need to click Save.
7) Communication protocol
Select the protocol according to the requirements. In order to prevent the user from
choosing by mistake, after opening the selected drop-down list, the user needs to
use the remote control to press the number key 7 for 10 times to unlock (the key
speed should not be too fast), and it will automatically restart if the selection is
successful.
3.3 Output display
1) Private car interface
Select the corresponding model, different models correspond to different interfaces,
and press the arrow keys Left and Right to change.
2) Resolution
HD resolution is recommended (1280x720). In order to prevent the user from
choosing by mistake, after opening the selected drop-down list, the user needs to
use the remote control to press the number 7 for 10 times to unlock (the key speed
should not be too fast), and it will automatically restart after the selection is
successful and click Save.
3) The position of the car model
Set the car model in the system image main interface to be displayed on the left or
right, and press the arrow keys Up and Down to change.
4) Video mode
Set whether the video signal is available or not, it is recommended to select the
video signal, and press the arrow keys Up and Down to change.
5) Turn on and look around
The 3D car model rotates once when it is turned on, and you can set whether to turn
it on or not.
6) Clock
Set the clock mode to forward or reverse, usually forward.
7) Video files
Set the duration of the video recording file, and press the arrow keys Up and Down to
change.
8) Touch Settings (Optional, this unit does not have this function yet.)
It can be set up with a touch function car screen to calibrate the touch accuracy of
the 360 panoramic video driving recorder. Click this function to display the following
picture, click on the picture to calibrate.
9) Color management
Adjust the brightness, contrast, saturation and chroma of the lens and the display
screen. Press the arrow keys Left and Right to select the lens , and change the value.
10) Display adjustment
Click Settings to pop up the debug box as shown in the figure below. First select
“Zoom” to adjust the display size. The arrow key Left zooms in left and right, and the
arrow key Right zooms out left and right; the arrow key Up zooms in up and down,
and arrow key Down zooms out up and down.
Then select Move, use the arrow keys to move the display area, select a suitable
location, and click Save.
3.4 Calibration debugging
3.4.1 Lens parameters
Select the corresponding camera parameters to achieve better image and calibration
effects, and change the direction keys up and down.
3.4.2 Image front and back
Set the front and rear lens upright and upside down, and press the arrow keys Up
and Down to change.
3.4.3 Export configuration
Export the calibration data of the 360 panoramic image recorder to a USB flash drive.
3.4.4 Import configuration
Import the calibration data in the USB to the system.
3.4.5 Module Type
Select the module corresponding to the lens, and press the arrow keys Up and Down
to change.
3.4.6 Panoramic Calibration
360 Panoramic calibration is divided into four ways.
1. Place the two pieces of cloth in front and back;
Park the vehicle uprightly. Put a piece of calibration cloth on the front and back of
the vehicle. The distance from the vehicle to the cloth is 30CM(or 40CM). The
straight line at the center of the cloth faces the center of the bodywork.
2. Select the correct module and lens in the calibration debugging menu;
3. Panorama calibration --- large cloth 4m8 automatic --- increase identification
points
4. Fine adjustment.
Attention: The input value of vehicle width, vehicle length and left and right offset is
used for calibration input of 4 pieces of 1.2m calibration cloth, and it is not necessary
to input this value for two pieces of large cloth.
Sample - 1 calibration cloths and 4 marker points
Select the corresponding lens (front, rear, left, right) to add marker points. Marker
points are wrongly drawn, choose to delete.
Front camera ↑ Back camera ↑
Left camera ↑ Right camera ↑
Sample - 2 calibration cloths and 8 marker points
Select the corresponding lens (front, rear, left, right) to add marker points. Marker
points are wrongly drawn, choose to delete.
Front camera ↑ Back camera ↑
Left camera ↑ Right camera ↑
Two large calibration cloths 4m8 automatic calibration
Press”1” for all cameras; press Up and Down for singer camera’s auto calibration
Done Done
Done Done
Press”1” for all cameras; press Up and Down for singer camera’s auto calibration
Press the number 1 on the remote control to calibrate all the shots, and the system
will automatically trace the points. After the calibration is complete, it will display the
calibration. Press the Return button on the remote control to see the calibration
effect.
[Link] Stitching optimization
This function can be used if the 4 cameras complete the operation of drawing marker
points according to the manual, but the stitching effect is not very satisfactory. Click
one-key calibration to optimize, and the system will automatically optimize. Select
the camera to be adjusted and adjust according to the operation prompts.
[Link] Add markers/modify markers
Manually reset marker points for accurate calibration.
3.4.7 Restore settings
To restore the output value or restore the original value. Owners should not operate
this function.
3.4.8 Fine adjustment
This function adjusts the display range and position of the front, rear, left and right
cameras.
3.4.9 Lens Correction
The moving circle is concentric with the brightness circle of the lens (the circle and
the junction of black and white are uniform or fully coincident.)
Adjust the 4 cameras until the view images are correct. The black plaid of the cloth
should be viewable from each of the 4 cameras, and 4 images seem parallel. Side
cameras should share the same view range.
3.5 Storage Management
If the 360 panoramic assist system cannot recognize the USB, you can format the USB
(please save important video files before formatting), and you can check the storage
capacity information of the USB
3.6 System maintenance
It is used to check the information of system version, upgrade system programs,
upgrade expansion modules, upgrade LOGO, system restart and other function
setting operations.
Common troubleshooting methods
1. The system does not turn on after starting: please check whether the connection
cable is powered on normally.
2. Abnormal phenomena such as crash: please press the reset button RESET.
3. The video becomes blurred: please check the lens for dust, please wipe the lens
and the front windshield!
4. Pressing the Power button does not turn on the machine: please check whether
the connection is powered on normally.
Disclaimer
1. The 360 Panoramic Assist System is a recording device for related information such
as images and sounds while the vehicle is driving, and it is only used as an auxiliary
reference when an accident occurs.
2. The audio of the 360 Panoramic Assist System is used as a reference, and our
company is not responsible for the bad files, data loss and other reasons caused by
abnormal conditions of the machine.
