7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Topic 1 - Single Topic

Question #1 Topic 1

Refer to the exhibit. Users in the branch network of [Link]/64 report that they cannot access the Internet.

Which command is issued in IPv6 router EIGRP 100 configuration mode to solve this issue?

A. Issue the eigrp stub command on R1.

B. Issue the no eigrp stub command on R1. Most Voted

C. Issue the eigrp stub command on R2.

D. Issue the no eigrp stub command on R2.

Correct Answer: B

Community vote distribution

B (100%)

[Link] 1/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #2 Topic 1

Refer to the exhibit. Which configuration configures a policy on R1 to forward any traffic that is sourced from the [Link]/24 network to R2?

A.

B.

C.

D.

Correct Answer: D

[Link] 2/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #3 Topic 1

R2 has a locally originated prefix [Link]/24 and has these configurations:

What is the result when the route-map OUT command is applied toward an eBGP neighbor R1 ([Link]) by using the neighbor [Link] route-map

OUT out command?

A. R1 sees [Link]/24 as two AS hops away instead of one AS hop away. Most Voted

B. R1 does not accept any routes other than [Link]/24

C. R1 does not forward traffic that is destined for [Link]/24

D. Network [Link]/24 is not allowed in the R1 table

Correct Answer: A

Community vote distribution

A (84%) B (16%)

Question #4 Topic 1

Which method changes the forwarding decision that a router makes without first changing the routing table or influencing the IP data plane?

A. nonbroadcast multiaccess

B. packet switching

C. policy-based routing Most Voted

D. forwarding information base

Correct Answer: C

Community vote distribution

C (91%) 9%

[Link] 3/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #5 Topic 1

Refer to the exhibits. The output of the trace route from R5 shows a loop in the network.

Which configuration prevents this loop?

A.

[Link] 4/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

B.

C.

D.

Correct Answer: B

[Link] 5/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #6 Topic 1

Refer to the exhibit. An engineer configures a static route on a router, but when the engineer checks the route to the destination, a different next

hop is chosen.

What is the reason for this?

A. Dynamic routing protocols always have priority over static routes.

B. The metric of the OSPF route is lower than the metric of the static route.

C. The configured AD for the static route is higher than the AD of OSPF. Most Voted

D. The syntax of the static route is not valid, so the route is not considered.

Correct Answer: C

Community vote distribution

C (100%)

[Link] 6/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #7 Topic 1

Refer to the exhibit. An engineer is trying to generate a summary route in OSPF for network [Link]/8, but the summary route does not show up in

the routing table.

Why is the summary route missing?

A. The summary-address command is used only for summarizing prefixes between areas.

B. The summary route is visible only in the OSPF database, not in the routing table.

C. There is no route for a subnet inside [Link]/8, so the summary route is not generated. Most Voted

D. The summary route is not visible on this router, but it is visible on other OSPF routers in the same area.

Correct Answer: C

Community vote distribution

C (100%)

[Link] 7/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #8 Topic 1

Refer to the exhibit. An engineer is trying to block the route to [Link] from the routing table by using the configuration that is shown. The

route is still present in the routing table as an OSPF route.

Which action blocks the route?

A. Use an extended access list instead of a standard access list.

B. Change sequence 10 in the route-map command from permit to deny. Most Voted

C. Use a prefix list instead of an access list in the route map.

D. Add this statement to the route map: route-map RM-OSPF-DL deny 20.

Correct Answer: B

Community vote distribution

B (87%) 13%

Question #9 Topic 1

What is a prerequisite for configuring BFD?

A. Jumbo frame support must be configured on the router that is using BFD.

B. All routers in the path between two BFD endpoints must have BFD enabled.

C. Cisco Express Forwarding must be enabled on all participating BFD endpoints. Most Voted

D. To use BFD with BGP, the timers 3 9 command must first be configured in the BGP routing process.

Correct Answer: C

Community vote distribution

C (100%)

[Link] 8/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #10 Topic 1

DRAG DROP -

Drag and drop the OSPF adjacency states from the left onto the correct descriptions on the right.

Select and Place:

Correct Answer:

Reference:

[Link]

[Link] 9/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #11 Topic 1

Refer to the exhibit. R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns the route to [Link]/24 from

R1, but it does not advertise to R3.

What is the reason the route is not advertised?

A. R2 does not have a route to the next hop, so R2 does not advertise the prefix to other clients. Most Voted

B. Route reflector setup requires full IBGP mesh between the routers.

C. In route reflector setup, only classful prefixes are advertised to other clients.

D. In route reflector setups, prefixes are not advertised from one client to another.

Correct Answer: A

Community vote distribution

A (100%)

[Link] 10/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #12 Topic 1

Refer to the exhibit. An engineer is trying to redistribute OSPF to BGP, but not all of the routes are redistributed.

What is the reason for this issue?

A. By default, only internal routes and external type 1 routes are redistributed into BGP

B. Only classful networks are redistributed from OSPF to BGP

C. BGP convergence is slow, so the route will eventually be present in the BGP table

D. By default, only internal OSPF routes are redistributed into BGP Most Voted

Correct Answer: D

Community vote distribution

D (100%)

[Link] 11/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #13 Topic 1

Refer to the exhibit. In which circumstance does the BGP neighbor remain in the idle condition?

A. if prefixes are not received from the BGP peer

B. if prefixes reach the maximum limit

C. if a prefix list is applied on the inbound direction

D. if prefixes exceed the maximum limit Most Voted

Correct Answer: D

Community vote distribution

D (100%)

Question #14 Topic 1

Which attribute eliminates LFAs that belong to protected paths in situations where links in a network are connected through a common fiber?

A. shared risk link group-disjoint Most Voted

B. linecard-disjoint

C. lowest-repair-path-metric

D. interface-disjoint

Correct Answer: A

Community vote distribution

A (100%)

[Link] 12/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #15 Topic 1

Refer to the exhibit. An engineer is troubleshooting BGP on a device but discovers that the clock on the device does not correspond to the time

stamp of the log entries.

Which action ensures consistency between the two times?

A. Configure the service timestamps log uptime command in global configuration mode.

B. Configure the logging clock synchronize command in global configuration mode.

C. Configure the service timestamps log datetime localtime command in global configuration mode. Most Voted

D. Make sure that the clock on the device is synchronized with an NTP server.

Correct Answer: C

Community vote distribution

C (90%) 10%

Question #16 Topic 1

Refer to the exhibit. What is the result of applying this configuration?

A. The router can form BGP neighborships with any other device.

B. The router cannot form BGP neighborships with any other device.

C. The router cannot form BGP neighborships with any device that is matched by the access list named ‫ג‬€BGP‫ג‬€. Most Voted

D. The router can form BGP neighborships with any device that is matched by the access list named ‫ג‬€BGP‫ג‬€.

Correct Answer: C

Community vote distribution

C (100%)

[Link] 13/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #17 Topic 1

Which command displays the IP routing table information that is associated with VRF-Lite?

A. show ip vrf

B. show ip route vrf Most Voted

C. show run vrf

D. show ip protocols vrf

Correct Answer: B

Community vote distribution

B (100%)

Question #18 Topic 1

Refer to the exhibit. Which subnet is redistributed from EIGRP to OSPF routing protocols?

A. [Link]/24 Most Voted

B. [Link]/26

C. [Link]/24

D. [Link]/26

Correct Answer: A

Community vote distribution

A (100%)

[Link] 14/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #19 Topic 1

Which configuration adds an IPv4 interface to an OSPFv3 process in OSPFv3 address family configuration?

A. router ospfv3 1 address-family ipv4

B. Router(config-router)#ospfv3 1 ipv4 area 0

C. Router(config-if)#ospfv3 1 ipv4 area 0 Most Voted

D. router ospfv3 1 address-family ipv4 unicast

Correct Answer: C

Community vote distribution

C (100%)

Question #20 Topic 1

Refer to the exhibit. Which statement about R1 is true?

A. OSPF redistributes RIP routes only if they have a tag of one.

B. RIP learned routes are distributed to OSPF with a tag value of one. Most Voted

C. R1 adds one to the metric for RIP learned routes before redistributing to OSPF.

D. RIP routes are redistributed to OSPF without any changes.

Correct Answer: B

Community vote distribution

B (100%)

[Link] 15/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #21 Topic 1

Refer to the exhibit. An IP SLA was configured on router R1 that allows the default route to be modified in the event that Fa0/0 loses reachability

with the router R3

Fa0/0 interface. The route has changed to flow through router R2.

Which debug command is used to troubleshoot this issue?

A. debug ip flow

B. debug ip sla error

C. debug ip routing Most Voted

D. debug ip packet

Correct Answer: C

Community vote distribution

C (83%) B (17%)

Question #22 Topic 1

Which configuration enables the VRF that is labeled `Inet` on FastEthernet0/0?

A. R1(config)# ip vrf Inet R1(config-vrf)#ip vrf FastEthernet0/0

B. R1(config)#ip vrf Inet FastEthernet0/0

C. R1(config)# ip vrf Inet R1(config-vrf)#interface FastEthernet0/0 R1(config-if)#ip vrf forwarding Inet Most Voted

D. R1(config)#router ospf 1 vrf Inet R1(config-router)#ip vrf forwarding FastEthernet0/0

Correct Answer: C

Community vote distribution

C (100%)

[Link] 16/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #23 Topic 1

Refer to the exhibit. After redistribution is enabled between the routing protocols; PC2, PC3, and PC4 cannot reach PC1.

Which action can the engineer take to solve the issue so that all the PCs are reachable?

A. Set the administrative distance 100 under the RIP process on R2. Most Voted

B. Filter the prefix [Link]/24 when redistributed from OSPF to EIGRP.

C. Filter the prefix [Link]/24 when redistributed from RIP to EIGRP.

D. Redistribute the directly connected interfaces on R2.

Correct Answer: A

Community vote distribution

A (95%) 5%

[Link] 17/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #24 Topic 1

Refer to the exhibit. A router is receiving BGP routing updates from multiple neighbors for routes in AS 690.

What is the reason that the router still sends traffic that is destined to AS 690 to a neighbor other than [Link]?

A. The local preference value in another neighbor statement is higher than 250.

B. The local preference value should be set to the same value as the weight in the route map.

C. The route map is applied in the wrong direction.

D. The weight value in another neighbor statement is higher than 200. Most Voted

Correct Answer: D

Community vote distribution

D (100%)

[Link] 18/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #25 Topic 1

Refer to the exhibit. R1 and R2 cannot establish an EIGRP adjacency.

Which action establishes EIGRP adjacency?

A. Remove the current autonomous system number on one of the routers and change to a different value.

B. Add the passive-interface command to the R1 configuration so that it matches the R2 configuration.

C. Remove the passive-interface command from the R2 configuration so that it matches the R1 configuration. Most Voted

D. Add the no auto-summary command to the R2 configuration so that it matches the R1 configuration.

Correct Answer: C

Community vote distribution

C (100%)

[Link] 19/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #26 Topic 1

An engineer configured policy-based routing for a destination IP address that does not exist in the routing table.

How is the packet treated through the policy for configuring the set ip default next-hop command?

A. Packets are not forwarded to the specific next hop.

B. Packets are forwarded based on the routing table.

C. Packets are forwarded based on a static route.

D. Packets are forwarded to the specific next hop. Most Voted

Correct Answer: D

Community vote distribution

D (94%) 3%

Question #27 Topic 1

Refer to the exhibit. The administrator configured route advertisement to a remote low resources router to use only the default route to reach any

network but failed.

Which action resolves this issue?

A. Remove the prefix keyword from the distribute-list command.

B. Remove the line with the sequence number 10 from the prefix list.

C. Change the direction of the distribute-list command from out to in.

D. Remove the line with the sequence number 5 from the prefix list. Most Voted

Correct Answer: D

Community vote distribution

D (100%)

[Link] 20/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #28 Topic 1

Refer to the exhibit. The network administrator configured the branch router for IPv6 on the E 0/0 interface. The neighboring router is fully

configured to meet requirements, but the neighbor relationship is not coming up.

Which action fixes the problem on the branch router to bring the IPv6 neighbors up?

A. Disable OSPF for IPv4 using the no ospfv3 4 area 0 ipv4 command under the E 0/0 interface.

B. Enable the IPv4 address family under the router ospfv3 4 process by using the address-family ipv4 unicast command. Most Voted

C. Disable IPv6 on the E 0/0 interface using the no ipv6 enable command.

D. Enable the IPv4 address family under the E 0/0 interface by using the address-family ipv4 unicast command.

Correct Answer: B

Community vote distribution

B (100%)

[Link] 21/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #29 Topic 1

Refer to the exhibit. The network administrator has configured the Customer Edge router (AS 64511) to send only summarized routes toward ISP-1

(AS 100) and

ISP-2 (AS 200).

After this configuration, ISP-1 and ISP-2 continue to receive the specific routes and the summary route.

Which configuration resolves the issue?

A.

B.

[Link] 22/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

C.

D.

Correct Answer: A

[Link] 23/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #30 Topic 1

Refer to the exhibit. R2 has two paths to reach [Link]/24, but traffic is sent only through R3.

Which action allows traffic to use both paths?

A. Configure the variance 4 command under the EIGRP process on R2. Most Voted

B. Configure the bandwidth 2000 command under interface FastEthernet0/0 on R2.

C. Configure the delay 1 command under interface FastEthernet0/0 on R2.

D. Configure the variance 2 command under the EIGRP process on R2.

Correct Answer: A

Community vote distribution

A (100%)

[Link] 24/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #31 Topic 1

Refer to the exhibit. The OSPF neighbor relationship is not coming up.

What must be configured to restore OSPF neighbor adjacency?

A. matching hello timers

B. OSPF on the remote router

C. use router ID

D. matching mtu values Most Voted

Correct Answer: D

Community vote distribution

D (100%)

Question #32 Topic 1

An engineer configured two routers connected to two different service providers using BGP with default attributes. One of the links is presenting

high delay, which causes slowness in the network.

Which BGP attribute must the engineer configure to avoid using the high-delay ISP link if the second ISP link is up?

A. AS-PATH

B. WEIGHT

C. MED

D. LOCAL_PREF Most Voted

Correct Answer: D

Community vote distribution

D (100%)

[Link] 25/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #33 Topic 1

Refer to the exhibit. A network administrator redistributed the default static route into OSPF toward all internal routers to reach to Internet.

Which set of commands restores reachability to the Internet by internal routers?

A. router ospf 1 redistribute static subnets

B. router ospf 1 network [Link] [Link] area 0

C. router ospf 1 redistribute connected [Link]

D. router ospf 1 default-information originate Most Voted

Correct Answer: D

Community vote distribution

D (100%)

[Link] 26/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #34 Topic 1

Refer to the exhibit. The Math and Science departments connect through the corporate IT router, but users in the Math department must not be

able to reach the

Science department and vice versa.

Which configuration accomplishes this task?

A. vrf definition Science address-family ipv4 ! interface E 0/2 ip address [Link] [Link] no shut ! interface E 0/3 ip address

[Link] [Link] no shut

B. vrf definition Science address-family ipv4 ! interface E 0/2 vrf forwarding Science ip address [Link] [Link] no shut ! interface

E 0/3 vrf forwarding Science ip address [Link] [Link] no shut Most Voted

C. vrf definition Science address-family ipv4 ! interface E 0/2 ip address [Link] [Link] vrf forwarding Science no shut ! interface

E 0/3 ip address [Link] [Link] vrf forwarding Science no shut

D. vrf definition Science ! interface E 0/2 ip address [Link] [Link] no shut ! interface E 0/3 ip address [Link]

[Link] no shut

Correct Answer: B

Community vote distribution

B (100%)

[Link] 27/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #35 Topic 1

Refer to the exhibit. The neighbor relationship is not coming up.

Which two configurations bring the adjacency up? (Choose two.)

A. LA interface E 0/0 ip ospf authentication-key Cisco123

B. NY interface E 0/0 no ip ospf message-digest-key 1 md5 Cisco123 ip ospf authentication-key Cisco123

C. LA interface E 0/0 ip ospf message-digest-key 1 md5 Cisco123 Most Voted

D. LA router ospf 1 area 0 authentication message-digest Most Voted

E. NY router ospf 1 area 0 authentication message-digest

Correct Answer: CD

Community vote distribution

CD (100%)

[Link] 28/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #36 Topic 1

Refer to the exhibit. The network administrator configured redistribution on an ASBR to reach to all WAN networks but failed.

Which action resolves the issue?

A. The route map EIGRP->OSPF must have the [Link]/24 entry to exist in one of the three prefix lists to pass

B. EIGRP must redistribute the [Link]/24 route instead of using the network statement

C. The OSPF process must have a metric when redistributing prefixes from EIGRP

D. The route map must have the keyword prefix-list to evaluate the prefix list entries Most Voted

Correct Answer: D

Community vote distribution

D (100%)

[Link] 29/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #37 Topic 1

Refer to the exhibit. An engineer configured R2 and R5 as route reflectors and noticed that not all routes are sent to R1 to advertise to the eBGP

peers.

Which iBGP routers must be configured as route reflectors to advertise all routes to restore reachability across all networks?

A. R1 and R4

B. R1 and R5

C. R4 and R5 Most Voted

D. R2 and R5

Correct Answer: C

Community vote distribution

C (85%) A (15%)

[Link] 30/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #38 Topic 1

[Link] 31/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

[Link] 32/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Refer to the exhibits. SanFrancisco and Boston routers are choosing slower links to reach each other despite the direct links being up.

Which configuration fixes the issue?

A. All Routers router ospf 1 auto-cost reference-bandwidth 100

B. SanFrancisco Router router ospf 1 auto-cost reference-bandwidth 1000

C. Boston Router router ospf 1 auto-cost reference-bandwidth 1000

D. All Routers router ospf 1 auto-cost reference-bandwidth 1000 Most Voted

Correct Answer: D

Community vote distribution

D (100%)

[Link] 33/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #39 Topic 1

Refer to the exhibit. Troubleshoot and ensure that branch ‫ ’׀‬only ever uses the MPLS ‫ ’׀‬network to reach HQ.

Which action achieves this requirement?

A. Introduce AS path prepending on the branch A MPLS ‫ ’׀‬network connection so that any HQ advertisements from branch A toward the MPLS

‫ ’׀‬network are prepended three times

B. Modify the weight of all HQ prefixes received at branch ‫ ’׀‬from the MPLS ‫ ’׀‬network to be higher than the weights used on the MPLS A

network

C. Increase the local preference for all HQ prefixes received at branch ‫ ’׀‬from the MPLS ‫ ’׀‬network to be higher than the local preferences used

on the MPLS A network

D. Introduce an AS path filter on branch A routers so that only local prefixes are advertised into BGP Most Voted

Correct Answer: D

Community vote distribution

D (100%)

[Link] 34/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #40 Topic 1

Refer to the exhibit. The OSPF routing protocol is redistributed into the BGP routing protocol, but not all the OSPF routes are distributed into BGP.

Which action resolves the issue?

A. Include the word external in the redistribute command

B. Use a route-map command to redistribute OSPF external routes defined in an access list

C. Include the word internal external in the redistribute command Most Voted

D. Use a route-map command to redistribute OSPF external routes defined in a prefix list

Correct Answer: C

Community vote distribution

C (76%) A (24%)

[Link] 35/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #41 Topic 1

Refer to the exhibit. Routing protocols are mutually redistributed on R3 and R1. Users report intermittent connectivity to services hosted on the

[Link]/24 prefix.

Significant routing update changes are noticed on R3 when the show ip route profile command is run.

How must the services be stabilized?

A. The routing loop must be fixed by reducing the admin distance of OSPF from 110 to 80 on R3

B. The routing loop must be fixed by reducing the admin distance of iBGP from 200 to 100 on R3 Most Voted

C. The issue with using BGP must be resolved by using another protocol and redistributing it into EIGRP on R3

D. The issue with using iBGP must be fixed by running eBGP between R3 and R4

Correct Answer: B

Community vote distribution

B (100%)

[Link] 36/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #42 Topic 1

When determining if a system is capable of support, what is the minimum time spacing required for a BFD control packet to receive once a control

packet is arrived?

A. Desired Min TX Interval

B. Detect Mult

C. Required Min RX Interval Most Voted

D. Required Min Echo RX Interval

Correct Answer: C

Community vote distribution

C (100%)

Question #43 Topic 1

An engineer is configuring a network and needs packets to be forwarded to an interface for any destination address that is not in the routing table.

What should be configured to accomplish this task?

A. set ip next-hop

B. set ip default next-hop Most Voted

C. set ip next-hop recursive

D. set ip next-hop verify-availability

Correct Answer: B

Community vote distribution

B (100%)

Question #44 Topic 1

What is an advantage of using BFD?

A. It detects local link failure at layer 1 and updates the routing table.

B. It detects local link failure at layer 3 and updates the routing protocols.

C. It has sub-second failure detection for layer 1 and layer 3 problems.

D. It has sub-second failure detection for layer 1 and layer 2 problems. Most Voted

Correct Answer: D

Community vote distribution

D (54%) B (44%)

[Link] 37/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #45 Topic 1

An engineer needs dynamic routing between two routers and is unable to establish OSPF adjacency. The output of the show ip ospf neighbor

command shows that the neighbor state is EXSTART/EXCHANGE.

Which action should be taken to resolve this issue?

A. match the passwords

B. match the hello timers

C. match the MTUs Most Voted

D. match the network types

Correct Answer: C

Reference:

[Link]

Community vote distribution

C (100%)

Question #46 Topic 1

Refer to the exhibit. R1 is connected with R2 via GigabitEthernet0/0, and R2 cannot ping R1.

What action will fix the issue?

A. Fix route dampening configured on the router.

B. Replace the SFP module because it is not supported.

C. Fix IP Event Dampening configured on the interface. Most Voted

D. Correct the IP SLA probe that failed.

Correct Answer: C

Community vote distribution

C (100%)

[Link] 38/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #47 Topic 1

Refer to the exhibits. A user on the [Link]/24 network can successfully ping [Link], but the administrator cannot ping [Link]

from the LA router.

Which set of configurations fixes the issue?

A.

B.

C.

D.

Correct Answer: D

[Link] 39/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #48 Topic 1

Refer to the exhibit. A network administrator configured mutual redistribution on R1 and R2 routers, which caused instability in the network.

Which action resolves the issue?

A. Set a tag in the route map when redistributing EIGRP into OSPF on R1, and match the same tag on R2 to deny when redistributing OSPF into

EIGRP. Most Voted

B. Set a tag in the route map when redistributing EIGRP into OSPF on R1, and match the same tag on R2 to allow when redistributing OSPF into

EIGRP.

C. Apply a prefix list of EIGRP network routes in OSPF domain on R1 to propagate back into the EIGRP routing domain.

D. Advertise summary routes of EIGRP to OSPF and deny specific EIGRP routes when redistributing into OSPF.

Correct Answer: A

Community vote distribution

A (100%)

[Link] 40/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Question #49 Topic 1

Refer to the exhibit. A network engineer for AS64512 must remove the inbound and outbound traffic from link A during maintenance without

closing the BGP session so that there is still a backup link over link A toward the ASN.

Which BGP configuration on R1 accomplishes this goal?

A.

B.

C.

[Link] 41/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

D.

Correct Answer: C

Question #50 Topic 1

An engineer configured access list NON-CISCO in a policy to influence routes.

What are the two effects of this route map configuration? (Choose two.)

A. Packets are forwarded using normal route lookup. Most Voted

B. Packets are forwarded to the default gateway.

C. Packets are dropped by the access list.

D. Packets are evaluated by sequence 10. Most Voted

E. Packets are not evaluated by sequence 10.

Correct Answer: AD

Community vote distribution

AD (74%) 13% 13%

Next Questions 

Browse atleast 50% to increase passing rate

[Link] 42/43
7/3/25, 4:03 PM 300-410 Exam - Free Actual Q&As, Page 1 | ExamTopics

Viewing page 1 out of 13 pages.

Viewing questions 1-50 out of 620 questions

[Link] 43/43