LAB GUIDE
VXLAN EVPN
IMPORTANT! THIS GUIDE ASSUMES THAT THE AOS-CX OVA HAS BEEN INSTALLED AND WORKS IN GNS3 OR EVE-NG. PLEASE
REFER TO GNS3/EVE-NG INITIAL SETUP LABS IF REQUIRED.
https://www.eve-ng.net/index.php/documentation/howtos/howto-add-aruba-cx-switch/
TABLE OF CONTENTS
Lab Objective .............................................................................................................................................. 1
Lab Overview .............................................................................................................................................. 1
Lab Network Layout .................................................................................................................................... 2
Lab Tasks ................................................................................................................................................... 2
Task 1 – Lab setup ..................................................................................................................................... 2
Task 2 – Configure IP Underlay Interfaces.................................................................................................. 3
Task 3 – Configure IP Underlay with EVPN ................................................................................................ 5
Task 4 – Configure Leaf Switches with VXLAN ........................................................................................... 7
Task 5 – Configure Hosts (VPCS)............................................................................................................... 8
Task 6 – Final Validation ............................................................................................................................. 8
Appendix – Complete Configurations ........................................................................................................ 11
Lab Objective
This lab will enable the reader to gain hands on experience with L2 Virtual Extensible LAN (VXLAN) Ethernet VPN (EVPN).
Lab Overview
This lab as shown in Figure 1 will allow you to provide end hosts (Virtual PC Simulator - VPCS) on the same subnet with L2
overlay network connectivity across the VXLAN data plane tunnel created by EVPN control plane.
OSPF is used as the IP underlay Interior Gateway Protocol (IGP) to provide loopback connectivity for IBGP peering (AS#65001).
IBGP EVPN with Route Reflectors (RRs) are used in this example to prevent the need for full mesh IBGP peers.
VXLAN EVPN scales better compared to flood and learn static VXLAN and allows use cases such as distributed L3 anycast
gateways. Take note that L3 VXLAN does not currently work with AOS-CX VMs.
Spine1/Spine2 will function as IBGP EVPN RRs, while Leaf1/Leaf2 will function as IBGP EVPN RR clients.
VLAN 110 will be mapped to VXLAN Network Identifier (VNI) 110 to provide L2 overlay connectivity across the leaf switches.
1
Lab Guide
VXLAN EVPN
Lab Network Layout
Figure 1. Lab topology and addresses
Lab Tasks
Task 1 – Lab setup
For this lab refer to Figure 1 for topology and IP address details.
• Start all the devices, including VPCS hosts
• Open each switch console and log in with user “admin” and hit enter, so that no password is applied
• Change all hostnames as shown in the topology:
configure
hostname …
• On all devices, bring up required ports:
int 1/1/1-1/1/6
no shutdown
use “exit” to go back a level
• Validate LLDP neighbors appear as expected on each switch
show lldp neighbor
2
Lab Guide
VXLAN EVPN
Leaf1
Leaf1(config)# sh lld neighbor-info
LLDP Neighbor Information
=========================
Total Neighbor Entries : 2
Total Neighbor Entries Deleted : 0
Total Neighbor Entries Dropped : 0
Total Neighbor Entries Aged-Out : 0
LOCAL-PORT CHASSIS-ID PORT-ID PORT-DESC TTL SYS-NAME
------------------------------------------------------------------------------------------
1/1/2 08:00:09:8a:14:fa 1/1/2 1/1/2 120 Spine1
1/1/3 08:00:09:12:8e:9e 1/1/2 1/1/2 120 Spine2
Task 2 – Configure IP Underlay Interfaces
• Configure interfaces, IPs and required VLANs on the 4 switches
Leaf1
Leaf1(config)# int lo 0
Leaf1(config-loopback-if)# ip add 192.168.2.3/32
Leaf1(config-loopback-if)# ip ospf 1 area 0
OSPF process does not exist.
Do you want to create (y/n)? y
OSPF Area is not configured.
Do you want to create (y/n)? y
Leaf1(config-loopback-if)# router ospf 1
Leaf1(config-ospf-1)# router-id 192.168.2.3
Leaf1(config-ospf-1)# int 1/1/2
Leaf1(config-if)# ip add 192.168.4.1/31
Leaf1(config-if)# ip ospf 1 area 0
Leaf1(config-if)# ip ospf network point-to-point
Leaf1(config-if)# int 1/1/3
Leaf1(config-if)# ip add 192.168.4.5/31
Leaf1(config-if)# ip ospf 1 area 0
Leaf1(config-if)# ip ospf network point-to-point
Leaf2
Leaf2(config)# int lo 0
Leaf2(config-loopback-if)# ip add 192.168.2.4/32
Leaf2(config-loopback-if)# ip ospf 1 area 0
OSPF process does not exist.
Do you want to create (y/n)? y
OSPF Area is not configured.
Do you want to create (y/n)? y
Leaf2(config-loopback-if)# router ospf 1
Leaf2(config-ospf-1)# router-id 192.168.2.4
Leaf2(config-ospf-1)# int 1/1/2
Leaf2(config-if)# ip add 192.168.4.3/31
Leaf2(config-if)# ip ospf 1 area 0
Leaf2(config-if)# ip ospf network point-to-point
Leaf2(config-if)# int 1/1/3
Leaf2(config-if)# ip add 192.168.4.7/31
3
Lab Guide
VXLAN EVPN
Leaf2(config-if)# ip ospf 1 area 0
Leaf2(config-if)# ip ospf network point-to-point
Spine1
Spine1(config)# int lo 0
Spine1(config-loopback-if)# ip add 192.168.2.1/32
Spine1(config-loopback-if)# ip ospf 1 area 0
OSPF process does not exist.
Do you want to create (y/n)? y
OSPF Area is not configured.
Do you want to create (y/n)? y
Spine1(config-loopback-if)# router ospf 1
Spine1(config-ospf-1)# router-id 192.168.2.1
Spine1(config-ospf-1)# int 1/1/2
Spine1(config-if)# ip add 192.168.4.0/31
Spine1(config-if)# ip ospf 1 area 0
Spine1(config-if)# ip ospf network point-to-point
Spine1(config-if)# int 1/1/1
Spine1(config-if)# ip add 192.168.4.2/31
Spine1(config-if)# ip ospf 1 area 0
Spine1(config-if)# ip ospf network point-to-point
Spine2
Spine2(config)# int lo 0
Spine2(config-loopback-if)# ip add 192.168.2.2/32
Spine2(config-loopback-if)# ip ospf 1 area 0
OSPF process does not exist.
Do you want to create (y/n)? y
OSPF Area is not configured.
Do you want to create (y/n)? y
Spine2(config-loopback-if)# router ospf 1
Spine2(config-ospf-1)# router-id 192.168.2.2
Spine2(config-ospf-1)# int 1/1/2
Spine2(config-if)# ip add 192.168.4.4/31
Spine2(config-if)# ip ospf 1 area 0
Spine2(config-if)# ip ospf network point-to-point
Spine2(config-if)# int 1/1/1
Spine2(config-if)# ip add 192.168.4.6/31
Spine2(config-if)# ip ospf 1 area 0
Spine2(config-if)# ip ospf network point-to-point
• Verify OSPF neighbors appear as expected between the switches
Leaf1(config)# sh ip os neighbors
OSPF Process ID 1 VRF default
==============================
Total Number of Neighbors: 2
Neighbor ID Priority State Nbr Address Interface
-------------------------------------------------------------------------
192.168.2.1 n/a FULL 192.168.4.0 1/1/2
192.168.2.2 n/a FULL 192.168.4.4 1/1/3
4
Lab Guide
VXLAN EVPN
• Verify OSPF routes are learnt as expected, you should see ECMP routes towards Lo0 of the other leaf, this is supposed to
allow VXLAN traffic to be load shared across the ECMP routes (this works with real hardware, however AOS-CX VMs do not
currently support ECMP)
Leaf1(config)# sh ip ro ospf
Displaying ipv4 routes selected for forwarding
'[x/y]' denotes [distance/metric]
192.168.2.1/32, vrf default
via 192.168.4.0, [110/100], ospf
192.168.2.2/32, vrf default
via 192.168.4.4, [110/100], ospf
192.168.2.4/32, vrf default ECMP to Leaf2 Lo0
via 192.168.4.4, [110/200], ospf
via 192.168.4.0, [110/200], ospf
192.168.4.2/31, vrf default
via 192.168.4.0, [110/200], ospf
192.168.4.6/31, vrf default
via 192.168.4.4, [110/200], ospf
Task 3 – Configure IP Underlay with EVPN
• On spine switches, configure EVPN Route Reflectors (RR) towards the leaf switches (RR clients) using leaf loopback IPs as
neighbors
Spine1
Spine1(config)# router bgp 65001
Spine1(config-bgp)# bgp router-id 192.168.2.1
Spine1(config-bgp)# neighbor 192.168.2.3 remote-as 65001
Spine1(config-bgp)# neighbor 192.168.2.3 update-source loopback 0
Spine1(config-bgp)# neighbor 192.168.2.4 remote-as 65001
Spine1(config-bgp)# neighbor 192.168.2.4 update-source loopback 0
Spine1(config-bgp)# address-family l2vpn evpn
Spine1(config-bgp-l2vpn-evpn)# neighbor 192.168.2.3 activate
Spine1(config-bgp-l2vpn-evpn)# neighbor 192.168.2.3 route-reflector-client
BGP Session with this peer will be restarted
Spine1(config-bgp-l2vpn-evpn)# neighbor 192.168.2.3 send-community extended
Spine1(config-bgp-l2vpn-evpn)# neighbor 192.168.2.4 activate
Spine1(config-bgp-l2vpn-evpn)# neighbor 192.168.2.4 route-reflector-client
BGP Session with this peer will be restarted
Spine1(config-bgp-l2vpn-evpn)# neighbor 192.168.2.4 send-community extended
Spine2
Spine2(config-if)# router bgp 65001
Spine2(config-bgp)# bgp router-id 192.168.2.2
Spine2(config-bgp)# neighbor 192.168.2.3 remote-as 65001
Spine2(config-bgp)# neighbor 192.168.2.3 update-source loopback 0
Spine2(config-bgp)# neighbor 192.168.2.4 remote-as 65001
Spine2(config-bgp)# neighbor 192.168.2.4 update-source loopback 0
Spine2(config-bgp)# address-family l2vpn evpn
Spine2(config-bgp-l2vpn-evpn)# neighbor 192.168.2.3 activate
Spine2(config-bgp-l2vpn-evpn)# neighbor 192.168.2.3 route-reflector-client
BGP Session with this peer will be restarted
Spine2(config-bgp-l2vpn-evpn)# neighbor 192.168.2.3 send-community extended
Spine2(config-bgp-l2vpn-evpn)# neighbor 192.168.2.4 activate
5
Lab Guide
VXLAN EVPN
Spine2(config-bgp-l2vpn-evpn)# neighbor 192.168.2.4 route-reflector-client
BGP Session with this peer will be restarted
Spine2(config-bgp-l2vpn-evpn)# neighbor 192.168.2.4 send-community extended
Leaf1
Leaf1(config)# router bgp 65001
Leaf1(config-bgp)# bgp router-id 192.168.2.3
Leaf1(config-bgp)# neighbor 192.168.2.1 remote-as 65001
Leaf1(config-bgp)# neighbor 192.168.2.1 update-source loopback 0
Leaf1(config-bgp)# neighbor 192.168.2.2 remote-as 65001
Leaf1(config-bgp)# neighbor 192.168.2.2 update-source loopback 0
Leaf1(config-bgp)# address-family l2vpn evpn
Leaf1(config-bgp-l2vpn-evpn)# neighbor 192.168.2.1 activate
Leaf1(config-bgp-l2vpn-evpn)# neighbor 192.168.2.1 send-community extended
Leaf1(config-bgp-l2vpn-evpn)# neighbor 192.168.2.2 activate
Leaf1(config-bgp-l2vpn-evpn)# neighbor 192.168.2.2 send-community extended
Leaf2
Leaf2(config-if)# router bgp 65001
Leaf2(config-bgp)# bgp router-id 192.168.2.4
Leaf2(config-bgp)# neighbor 192.168.2.1 remote-as 65001
Leaf2(config-bgp)# neighbor 192.168.2.1 update-source loopback 0
Leaf2(config-bgp)# neighbor 192.168.2.2 remote-as 65001
Leaf2(config-bgp)# neighbor 192.168.2.2 update-source loopback 0
Leaf2(config-bgp)# address-family l2vpn evpn
Leaf2(config-bgp-l2vpn-evpn)# neighbor 192.168.2.1 activate
Leaf2(config-bgp-l2vpn-evpn)# neighbor 192.168.2.1 send-community extended
Leaf2(config-bgp-l2vpn-evpn)# neighbor 192.168.2.2 activate
Leaf2(config-bgp-l2vpn-evpn)# neighbor 192.168.2.2 send-community extended
• Validate EVPN neighbors are up on the leaf switches
Leaf1(config)# show bgp l2vpn evpn summary
VRF : default
BGP Summary
-----------
Local AS : 65001 BGP Router Identifier : 192.168.2.3
Peers : 2 Log Neighbor Changes : No
Cfg. Hold Time : 180 Cfg. Keep Alive : 60
Neighbor Remote-AS MsgRcvd MsgSent Up/Down Time State AdminStatus
192.168.2.1 65001 5 5 00h:01m:59s Established Up
192.168.2.2 65001 5 5 00h:01m:59s Established Up
• On leaf switches, configure the desired VLAN to be VXLAN encapsulated, this VLAN will be enabled towards Host1, Host2.
Specify the same vlan under evpn.
• RD and route-target can be left as auto for IBGP EVPN, these are advertised to other devices via “send-community
extended” configured previously
Leaf1
Leaf1(config)# vlan 110
Leaf1(config-vlan-110)#
Leaf1(config-vlan-110)# evpn
Leaf1(config-evpn)# vlan 110
Leaf1(config-evpn-vlan-110)# rd auto
6
Lab Guide
VXLAN EVPN
Leaf1(config-evpn-vlan-110)# route-target export auto
Leaf1(config-evpn-vlan-110)# route-target import auto
Leaf2
Leaf2(config)# vlan 110
Leaf2(config-vlan-110)#
Leaf2(config-vlan-110)# evpn
Leaf2(config-evpn)# vlan 110
Leaf2(config-evpn-vlan-110)# rd auto
Leaf2(config-evpn-vlan-110)# route-target export auto
Leaf2(config-evpn-vlan-110)# route-target import auto
Task 4 – Configure Leaf Switches with VXLAN
• On both leaf switches, configure the desired VLAN to be VXLAN encapsulated on the ports towards Host1, Host2
Leaf1
Leaf1(config)# int 1/1/1
Leaf1(config-if)# no routing
Leaf1(config-if)# vlan access 110
Leaf2
Leaf2(config)# int 1/1/1
Leaf2(config-if)# no routing
Leaf2(config-if)# vlan access 110
• Configure the VXLAN interface, the source IP based on Lo0 and the desired VLAN to VXLAN Network Identifier (VNI)
mapping
Leaf1
Leaf1(config)# interface vxlan 1
Leaf1(config-vxlan-if)# source ip 192.168.2.3
Leaf1(config-vxlan-if)# no shutdown
Leaf1(config-vxlan-if)# vni 110
Leaf1(config-vni-110)# vlan 110
Leaf2
Leaf2(config)# interface vxlan 1
Leaf2(config-vxlan-if)# source ip 192.168.2.4
Leaf2(config-vxlan-if)# no shutdown
Leaf2(config-vxlan-if)# vni 110
Leaf2(config-vni-110)# vlan 110
• Validate the VXLAN interface is up with correct source, destination VTEP peer IPs via EVPN and VNI/VLAN mapping.
Leaf1(config)# sh int vxlan
Interface vxlan1 is up
Admin state is up
Description:
Underlay VRF: default
Destination UDP port: 4789
VTEP source IPv4 address: 192.168.2.3
VNI VLAN VTEP Peers Origin
---------- ------ ----------------- --------
7
Lab Guide
VXLAN EVPN
110 110 192.168.2.4 evpn
• The leafs automatically create a VXLAN tunnel between them as they are both interested in the same VNI
• If wireshark is available https://www.eve-ng.net/index.php/features-compare/
• Setup and start wireshark packet captures
o right click on a leaf switch -> Capture -> 1/1/2 -> Ethernet
o also right click on the same switch, other uplink -> Capture -> 1/1/3 -> Ethernet
• Only 1 link might show the desired packet captures as ECMP is not supported on the AOS-CX VMs
Task 5 – Configure Hosts (VPCS)
• Configure Host1, Host2 with the desired IP and default gateway (the default gateway doesn’t exist on the network as L2
VXLAN is used but is a required config in VPCS, so we assume a .254 as the default gateway)
Host1
ip 10.0.110.1/24 10.0.110.254
Host2
ip 10.0.110.2/24 10.0.110.254
Task 6 – Final Validation
• Ensure L2 connectivity works between hosts
VPCS> ping 10.0.110.2
84 bytes from 10.0.110.2 icmp_seq=1 ttl=64 time=1.787 ms
84 bytes from 10.0.110.2 icmp_seq=2 ttl=64 time=3.202 ms
84 bytes from 10.0.110.2 icmp_seq=3 ttl=64 time=3.999 ms
84 bytes from 10.0.110.2 icmp_seq=4 ttl=64 time=3.055 ms
84 bytes from 10.0.110.2 icmp_seq=5 ttl=64 time=3.375 ms
• Validate local and remote MACs are seen on the leaf switches as expected
Leaf1# sh mac-address-table
MAC age-time : 300 seconds
Number of MAC addresses : 2
MAC Address VLAN Type Port
--------------------------------------------------------------
00:50:79:66:68:05 110 dynamic 1/1/1
00:50:79:66:68:07 110 evpn vxlan1(192.168.2.4)
8
Lab Guide
VXLAN EVPN
• Validate local and remote MACs are also seen in the EVPN table
Leaf1# sh bgp l2vpn evpn
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, e external S Stale, R Removed
Origin codes: i - IGP, e - EGP, ? - incomplete
EVPN Route-Type 2 prefix: [2]:[ESI]:[EthTag]:[MAC]:[OrigIP]
EVPN Route-Type 3 prefix: [3]:[EthTag]:[OrigIP]
VRF : default
Local Router-ID 192.168.2.3
Network Nexthop Metric LocPrf Weight
Path
-----------------------------------------------------------------------------------------------------------
-
Route Distinguisher: 192.168.2.3:110 (L2VNI 110)
*> [2]:[0]:[0]:[00:50:79:66:68:05]:[] 192.168.2.3 0 100 0 ?
*> [3]:[0]:[192.168.2.3] 192.168.2.3 0 100 0 ?
Route Distinguisher: 192.168.2.4:110 (L2VNI 110)
*>i [2]:[0]:[0]:[00:50:79:66:68:07]:[] 192.168.2.4 0 100 0 ?
* i [2]:[0]:[0]:[00:50:79:66:68:07]:[] 192.168.2.4 0 100 0 ?
*>i [3]:[0]:[192.168.2.4] 192.168.2.4 0 100 0 ?
* i [3]:[0]:[192.168.2.4] 192.168.2.4 0 100 0 ?
Total number of entries 6
• Validate VXLAN traffic is seen in the wireshark capture
• Validate EVPN mac address advertisements
9
Lab Guide
VXLAN EVPN
10
Lab Guide
VXLAN EVPN
Appendix – Complete Configurations
• If you face issues during your lab, you can verify your configs with the configs listed in this section
• If configs are the same, try powering off/powering on the switches to reboot them
Host1
VPCS> show ip
NAME : VPCS[1]
IP/MASK : 10.0.110.1/24
GATEWAY : 10.0.110.254
DNS :
MAC : 00:50:79:66:68:05
LPORT : 20000
RHOST:PORT : 127.0.0.1:30000
MTU : 1500
Host2
VPCS> show ip
NAME : VPCS[1]
IP/MASK : 10.0.110.2/24
GATEWAY : 10.0.110.254
DNS :
MAC : 00:50:79:66:68:07
LPORT : 20000
RHOST:PORT : 127.0.0.1:30000
MTU : 1500
Leaf1
Leaf1# sh run
Current configuration:
!
!Version ArubaOS-CX Virtual.10.05.0001
!export-password: default
hostname Leaf1
user admin group administrators password ciphertext
AQBapVMU52p/ytCYietVZGUk6tIqYw4Q6Akwu3365UgNKfHpYgAAADiRDONY/h2CBMH3N7BMvRRQl+cqX6RfeBJpVlnE4Fy
hoWrLRp7YL1hG4UUpF4eJxnNbkt00CM/6ZyxB
ZEC61b3HA1m04o3wLSbsWFvH9r83X+Tgd1xX3lsD0tOEKwfSPD6X
led locator on
!
!
!
!
ssh server vrf mgmt
vlan 1,110
evpn
vlan 110
rd auto
route-target export auto
route-target import auto
interface mgmt
no shutdown
ip dhcp
11
Lab Guide
VXLAN EVPN
interface 1/1/1
no shutdown
no routing
vlan access 110
interface 1/1/2
no shutdown
ip address 192.168.4.1/31
ip ospf 1 area 0.0.0.0
ip ospf network point-to-point
interface 1/1/3
no shutdown
ip address 192.168.4.5/31
ip ospf 1 area 0.0.0.0
ip ospf network point-to-point
interface 1/1/4
no shutdown
interface 1/1/5
no shutdown
interface 1/1/6
no shutdown
interface loopback 0
ip address 192.168.2.3/32
ip ospf 1 area 0.0.0.0
interface vxlan 1
source ip 192.168.2.3
no shutdown
vni 110
vlan 110
!
!
!
!
!
router ospf 1
router-id 192.168.2.3
area 0.0.0.0
router bgp 65001
bgp router-id 192.168.2.3
neighbor 192.168.2.1 remote-as 65001
neighbor 192.168.2.1 update-source loopback 0
neighbor 192.168.2.2 remote-as 65001
neighbor 192.168.2.2 update-source loopback 0
address-family l2vpn evpn
neighbor 192.168.2.1 activate
neighbor 192.168.2.1 send-community extended
neighbor 192.168.2.2 activate
neighbor 192.168.2.2 send-community extended
exit-address-family
!
https-server vrf mgmt
Leaf2
Leaf2# sh run
Current configuration:
!
!Version ArubaOS-CX Virtual.10.05.0001
!export-password: default
hostname Leaf2
user admin group administrators password ciphertext
AQBapatyqH0CftWF1n1MVl85TAbO9WDzCOquKut5MUry1/WkYgAAAFzxzdzLlkrDdw4XJpYgRjJEdVBzF3kg1JX6pqIm3dY
pLNRx2UaegUlKCLtL+eqqYKdmJizE/p0B1YkL
1PhYYLfX9riBS72YQdgzy/TWyK4KsoMBo0KOyA8HAwwl60LydmEK
12
Lab Guide
VXLAN EVPN
led locator on
!
!
!
!
ssh server vrf mgmt
vlan 1,110
evpn
vlan 110
rd auto
route-target export auto
route-target import auto
interface mgmt
no shutdown
ip dhcp
interface 1/1/1
no shutdown
no routing
vlan access 110
interface 1/1/2
no shutdown
ip address 192.168.4.3/31
ip ospf 1 area 0.0.0.0
ip ospf network point-to-point
interface 1/1/3
no shutdown
ip address 192.168.4.7/31
ip ospf 1 area 0.0.0.0
ip ospf network point-to-point
interface 1/1/4
no shutdown
interface 1/1/5
no shutdown
interface 1/1/6
no shutdown
interface loopback 0
ip address 192.168.2.4/32
ip ospf 1 area 0.0.0.0
interface vxlan 1
source ip 192.168.2.4
no shutdown
vni 110
vlan 110
!
!
!
!
!
router ospf 1
router-id 192.168.2.4
area 0.0.0.0
router bgp 65001
bgp router-id 192.168.2.4
neighbor 192.168.2.1 remote-as 65001
neighbor 192.168.2.1 update-source loopback 0
neighbor 192.168.2.2 remote-as 65001
neighbor 192.168.2.2 update-source loopback 0
address-family l2vpn evpn
neighbor 192.168.2.1 activate
neighbor 192.168.2.1 send-community extended
neighbor 192.168.2.2 activate
neighbor 192.168.2.2 send-community extended
exit-address-family
!
https-server vrf mgmt
13
Lab Guide
VXLAN EVPN
Spine1
Spine1# sh run
Current configuration:
!
!Version ArubaOS-CX Virtual.10.05.0001
!export-password: default
hostname Spine1
user admin group administrators password ciphertext
AQBapQmyufe7KU4F+7y0XkwIsvuwwy+1zBXxDKhnrN99muFCYgAAAMBAMUs8+7DMHMpSf5hWbuXPGW6AsSiV8gCMUVUvo0m
waV1h6lv8JKB784F5JpeRDhRZawQQwww8qWEb
75GleLUzv0KKWxfO68ZH/vyH4kS+mOlqBanG2FfUwLK3hlGp0WYX
led locator on
!
!
!
!
ssh server vrf mgmt
vlan 1
interface mgmt
no shutdown
ip dhcp
interface 1/1/1
no shutdown
ip address 192.168.4.2/31
ip ospf 1 area 0.0.0.0
ip ospf network point-to-point
interface 1/1/2
no shutdown
ip address 192.168.4.0/31
ip ospf 1 area 0.0.0.0
ip ospf network point-to-point
interface 1/1/3
no shutdown
interface 1/1/4
no shutdown
interface 1/1/5
no shutdown
interface 1/1/6
no shutdown
interface loopback 0
ip address 192.168.2.1/32
ip ospf 1 area 0.0.0.0
!
!
!
!
!
router ospf 1
router-id 192.168.2.1
area 0.0.0.0
router bgp 65001
bgp router-id 192.168.2.1
neighbor 192.168.2.3 remote-as 65001
neighbor 192.168.2.3 update-source loopback 0
neighbor 192.168.2.4 remote-as 65001
neighbor 192.168.2.4 update-source loopback 0
address-family l2vpn evpn
neighbor 192.168.2.3 activate
neighbor 192.168.2.3 route-reflector-client
neighbor 192.168.2.3 send-community extended
neighbor 192.168.2.4 activate
neighbor 192.168.2.4 route-reflector-client
neighbor 192.168.2.4 send-community extended
14
Lab Guide
VXLAN EVPN
exit-address-family
!
https-server vrf mgmt
Spine2
Spine2# sh run
Current configuration:
!
!Version ArubaOS-CX Virtual.10.05.0001
!export-password: default
hostname Spine2
user admin group administrators password ciphertext
AQBapQO37UTF26BBmzKTurSE0YYNBHnts3ccme3ZAtefD8lYYgAAAH904CccOVwhGS7zXBrJxrsC0EO5vND88i3JRpKdxDt
Eih6QtPpA23znBp11RH/J72YHm/iLDSHs0gWO
xadHnIwj3DnT/324kjPE2fQCN7Z8H7S1reE6Wbd1Hc808Iw5o6aM
led locator on
!
!
!
!
ssh server vrf mgmt
vlan 1
interface mgmt
no shutdown
ip dhcp
interface 1/1/1
no shutdown
ip address 192.168.4.6/31
ip ospf 1 area 0.0.0.0
ip ospf network point-to-point
interface 1/1/2
no shutdown
ip address 192.168.4.4/31
ip ospf 1 area 0.0.0.0
ip ospf network point-to-point
interface 1/1/3
no shutdown
interface 1/1/4
no shutdown
interface 1/1/5
no shutdown
interface 1/1/6
no shutdown
interface loopback 0
ip address 192.168.2.2/32
ip ospf 1 area 0.0.0.0
!
!
!
!
!
router ospf 1
router-id 192.168.2.2
area 0.0.0.0
router bgp 65001
bgp router-id 192.168.2.2
area 0.0.0.0
router bgp 65001
bgp router-id 192.168.2.2
neighbor 192.168.2.3 remote-as 65001
neighbor 192.168.2.3 update-source loopback 0
neighbor 192.168.2.4 remote-as 65001
15
Lab Guide
VXLAN EVPN
neighbor 192.168.2.4 update-source loopback 0
address-family l2vpn evpn
neighbor 192.168.2.3 activate
neighbor 192.168.2.3 route-reflector-client
neighbor 192.168.2.3 send-community extended
neighbor 192.168.2.4 activate
neighbor 192.168.2.4 route-reflector-client
neighbor 192.168.2.4 send-community extended
exit-address-family
!
https-server vrf mgmt
16
www.arubanetworks.com
3333 Scott Blvd. Santa Clara, CA 95054
1.844.472.2782 | T: 1.408.227.4500 | FAX: 1.408.227.4550 | [email protected]
17
