ABOUT ME
Teaching Experience: 7+ Years
Qualification: [Link] in Thermal Science & Engineering
Achievements
Mentored More Than 30,000+ Students
Area of Expertise: Mechanics, Heat Transfer, Industrial
Engineering, Theory of Machines, Maintenance, Engineering
Drawing.
Mail ID: sooraj.s9@[Link]
Telegram ID: Mechanical by Sooraj Gopi
SOORAJ GOPI
Join My Telegram Group
[Link] by Sooraj Gopi
For daily dose to improve concepts
For daily important questions
For latest information about exams
For notification of the class
For important PDFs & notes
For clearing the doubts by experts
SOORAJ GOPI
ISRO Mock Test
ISRO Mock Test
ISRO Mock Test
ISRO Mock Test
ISRO Mock Test
Q1. A footstep bearing and a rotor of a vertical
turbine forms an example of
A. incompletely constrained motion
B. partially constrained motion
C. completely constrained motion
D. successfully constrained motion
ISRO Mock Test
ISRO Mock Test
Q2. For an epicyclic gear train, the input torque = 100
Nm. RPM of the input gear is 1000 (clockwise),
while that of the output gear is 50 RPM
(anticlockwise). What is the magnitude of the
holding torque for the gear train?
A. Zero
B. 500 Nm
C. 2100 Nm
D. None of the above
ISRO Mock Test
ISRO Mock Test
ISRO Mock Test
Q3. OABC is a 4-bar mechanism
OA = 2 cm, AB = 2.2 cm, BC = 2.5 cm
Fixed link OC = 3.5 cm ,OA rotates at 10 rad/s
PO = 6 cm, PC = 6.5 cm, Extended OA meets
extended CB at P. What is the radial acceleration
of B w.r.t. C?
A. 40 cm/s2
B. 80 cm/s2
C. 160 cm/s2
D. 320 cm/s2
ISRO Mock Test
ISRO Mock Test
ISRO Mock Test
Q4. In an Oldham’s coupling, the maximum velocity
of sliding is 0.25 m/s. The driving shaft revolves at
180 rpm. Find the distance between the two parallel
shafts (in mm) ___________.
A. 10.58 B. 12.56
C. 13.26 D. 15.56
ISRO Mock Test
ISRO Mock Test
Q5. In case of a 4-link mechanism ABCD, AB = 3 cm,
BC = 4 cm, CD = 8 cm, DA = 6 cm. If CD is fixed, which
mechanism will be obtained ____________?
A. Crank-crank B. Double Rocker
C. Crank-Rocker D. Parallelogram linkage
ISRO Mock Test
ISRO Mock Test
Q6. Instantaneous centre of a sphere undergoing
pure rolling on a curved surface, lies at
A. Infinity
B. Centre of the sphere
C. Centre of the curved surface
D. Point of contact of spheres and the surface
ISRO Mock Test
ISRO Mock Test
Q7. PQRS is the 4-bar mechanism as shown below
where PQ = 300 mm, RS=600 mm link, PS is fixed, wPQ
= 5 rad/s. velocity of R, at instant shown in figure is
_______ m/sec?
A. 1 m/s
B. 1.5 m/s
C. 2 m/s
D. 2.5 m/s
ISRO Mock Test
ISRO Mock Test
Q8. According to Kennedy theorem, the three
instantaneous centers (Ics) of the three-link
mechanism having a relative motion between the
links lie on ______ .
A. A triangle
B. Parabola
C. Circle
D. Straight line
ISRO Mock Test
ISRO Mock Test
Q9. Two gears in mesh are having a constant velocity
ratio of 3 and module 2 mm. Find the circular pitch of
the gear (in mm) ________.
A. 6p B. 2p
C. 4p D. 7p
ISRO Mock Test
ISRO Mock Test
Q10. The module of a gear 1 (10 teeth) is 5 mm,
meshing with gear 2 has 20 teeth. Find the distance
between centres of the mating gears?
A. 30 mm B. 40 mm
C. 50 mm D. 75 mm
ISRO Mock Test
ISRO Mock Test
Q11. The equation of vibration of a system is
4x 49p2 x 0. Its natural frequency is _____ .
A. 3Hz B. 1.75Hz
C. 2.5Hz D. 3.5πHz
ISRO Mock Test
ISRO Mock Test
Q12. For a vibration system, equation of motion is
.. .
given as x 8 x 25x 0
The value of frequency of damped vibration is
______ (in rad/s).
A. 1.25 B. 1.36
C. 5 D. 3
ISRO Mock Test
ISRO Mock Test
Q13. Gyroscopic effect will be Zero in case of
_______ .
A. Steering during ship turns left
B. Steering during ship turns right
C. Ship during pitching
D. Ship during rolling
ISRO Mock Test
ISRO Mock Test
Q14. An aero plane is making a right turn. What is the
gyroscopic effect if the air screw rotates clockwise
when it is viewed from rear?
A. Raise the nose and depress the tail
B. Raise the tail and dip the nose
C. Tilt the aeroplane
D. None
ISRO Mock Test
ISRO Mock Test
Q15. If a planar mechanism with six links and seven
lower pairs, each lower pair is having one degree
of freedom, then the degrees of freedom of the
mechanism is ______.
A. 1
B. 2
C. 3
D. 0
ISRO Mock Test
ISRO Mock Test
Q16. For a four-bar planar mechanism, the links lengths
are as follows:
AB = 90 mm, BC = 40 mm, CD = 50 mm, and DA =
70 mm. In order to get crank-crank mechanism,
which of the following link should be fixed _____.
A. AB
B. BC
C. CD
D. Not possible
ISRO Mock Test
ISRO Mock Test
Q17. Piston reciprocating inside a cylinder is an
example of:
i. Completely constrained motion
ii. Incompletely constrained motion
iii. Successfully constrained motion
A. Only ii B. Both ii and iii
C. Only iii D. Both I and ii
ISRO Mock Test
ISRO Mock Test
Q18. Cycloidal gear tooth profile consists of
a. only cycloid
b. only hypocycloid
c. cycloid and epicycloid
d. hypocycloid and epicycloid
ISRO Mock Test
Q19. What type of progression will be followed by
the amplitude of free oscillations with coulomb
damping ?
A. Harmonic
B. Arithmetic
C. Logarithmic
D. Exponential
ISRO Mock Test
ISRO Mock Test
Q20. What causes a variation in the tractive effort of
an engine?
A. Unbalanced portion of primary force, along
line of stroke
B. Unbalanced portion of primary force,
perpendicular to line of stroke
C. The secondary force
D. Both primary and secondary unbalanced force
ISRO Mock Test
ISRO Mock Test
Q21. Logarithmic decrement of a damped single
degree of freedom system is δ . If the stiffness of
the spring is doubled and the mass is half, then
the logarithmic decrement of the new system will
be equal to
A. δ/4
B. δ/2
C. δ
D. 2δ
ISRO Mock Test
ISRO Mock Test
ISRO Mock Test
ISRO Mock Test
ISRO Mock Test
ISRO Mock Test
ISRO Mock Test
Join My Telegram Group
[Link] by Sooraj Gopi
For daily dose to improve concepts
For daily important questions
For latest information about exams
For notification of the class
For important PDFs & notes
For clearing the doubts by experts
SOORAJ GOPI
ISRO Mock Test
