SUMMARY G+0
item no Description Unit
A) SUB- STRUCTURE
1 Earth Work
2 CONCRETE WORK
B) SUPER- STRUCTURE
3 MASONRY WORK
4 BLOCK WORK
5 PLASTERING
6 PAINTING---with material
7 Roofing. ----only Labor
0
Quantity Unit Rate Amount
Project: G+0
Owner : Ethiopan Government
Location: Addis Ababa,Ethiopia
item no Description Unit Quantity Unit rate Amount
A) SUB- STRUCTURE
1. Earth Work
1.1 Excavation of black cotton soil m3 105.00 500.00 52,500.00
Back fill around footing pad and aruond massonry wall & hard core using
selected material from quarry/out side , compacted in layers , each layer not
exceeding 200 mm thick until it attains a minimum of 95% proctor density
1.2 m3 105.00 2,000.00 210,000.00
Load and cart away surplus excavated material away 2km from the project site to
waste area in compliance with all administrative and environmental regulation of
1.3 the project site. m3 48.00 200.00 9,600.00
250mm thick basaltic stone hardcore well rolled, consolidated and blinded with
1.4 crushed stone under semi basment floor slab. m3 140.00 2,600.00 364,000.00
1.5 10mm thick, styrofom expansion joint between ground floor slab & beam. ml 150.00 100.00 15,000.00
Total carried to summary 651,100.00
2. CONCRETE WORK
50 mm lean concrete quality C-5, shall have a minimum 28 day cylinder crushing
strength of 25N/mm2 with minimum cement content of 150 kg /m3, of concrete;
(AsEph Will only supply Sand,Agreegate and Cement)
2.1
A) Under Masonary Wall m2 55.00 210.00 11,550.00
B) under Ground slab m2 700 210.00 147,000.00
Reinforced concrete in class C-25 (with a 28-day 150mm cube crushing strength
of 25MPa), cast into formworks and vibrated around rod reinforcement bars.
(formwork & reinforcement bars are measured separately.) in: "Type of cement to
be ordinary Portland cement (PPC)" Price includes all the necessary machinery of
Mixer, Vibrator, Pully etc.(AsEph Will only supply Sand,Agreegate and
Cement)
2.2
A) For Grade Beam m3 16.50 1,300.00 21,450.00
A) For Intermidate Beam m3 16.50 1,300.00 21,450.00
A) For Toptie Beam m3 16.50 1,300.00 21,450.00
B) For Ground Column m3 6.12 1,300.00 7,956.00
E) 10mm thick concrete Ground slab m3 70 1,300.00 91,000.00
Total carried to summary 321,856
2.3 Form work( Only Labor)
The Contractor shall be responsible for the design and stability of the
formwork and false work. All forms shall be of wrought lumber and shall be
built mortar tight and of sufficient, rigidity to prevent distortion due to the
pressure of the concrete and other loads incident to the construction
operations.
Forms shall be constructed and maintained so as to prevent warping and the
opening of joints due to shrinkage of the lumber. Forms shall be inspected by the
Engineer prior to installation of reinforcement The number of spacing of the
form struts and braces shall be such that the forms will be braced rigidly and
uniformly lock joints between form sections shall be free from play or
movement.
A) For Grade Beam m2 110.00 300.00 33,000.00
B) For Intermidate Beam m2 30.00 300.00 9,000.00
C) For toptie Beam m2 110.00 300.00 33,000.00
D) For Ground Column m2 81.60 300.00 24,480.00
Total carried to summary 99,480.00
Project: G+0
Owner : Ethiopan Government
Location: Addis Ababa,Ethiopia
item no Description Unit Quantity Unit rate Amount
2.4 Reinforcement bar
All reinforcement shall be placed strictly in accordance with the drawings and as
instructed by the Eng. The ties, links or stirrups connecting the bars shall be put
so that the bars are properly braced the inside of their curved part small be in
actual contact with the bars, around which they are intended to fit. Wire for
bending reinforcement bars shall be of soft black mild steel wire.
The binding shall be twisted tight with proper pliers. The free ends of the
binding wire shall be bent inwards. Steel reinforcement shall be protected at all
times from injury. When placed in the work, it shall be free from dirt, paint, oil,
rust, grease or other foreign substances. Splicing: All reinforcement shall be
furnished in the full lengths indicated on the drawings.
Splicing bars, except where shown on the drawing, will not be permitted without
the written approval of the Eng. Splices shall be staggered as far as
possible.Additional splices, other than those shown on the drawings; and allowed
by the Eng., shall be at the contractor’s own expense. The cost of all supports for
holding reinforcement bars shall be borne by the Contractor. Price includes
cutting, bending, placing in position, tying wire and concrete spacers.
A) Diameter 8mm deformed bar kg 5494.19 10.00 54,941.88
B) Diameter 10mm deformed bar kg 1200.00 10.00 12,000.00
C) Diameter 12mm deformed bar kg 1644.75 10.00 16,447.52
Total carried to summary of reinforcement bar 83,389.40
Total carried to summary for concrete work 1,155,825.40
3. MASONRY WORK
The thickness of the wall should be 500mm the depth should be calculated from
the drawing and as per the order of the Engineer, the depth may vary according to
the NGL. The retaining masonry wall bedded in cement sand mortar ratio of
1:3. Masonry wall should be well dressed.Well rolled and consolidated.Mortar
mix ratio should be approved by the engineer .(when AsEph deliver
Sand,cement and Masonary)
m3 33 1,200.00 39,600.00
The thickness of the wall should be 500mm the depth should be calculated from
the drawing and as per the order of the Engineer, the depth may vary according to
the NGL. The retaining masonry wall bedded in cement sand mortar ratio of
1:3. Masonry wall should be well dressed.Well rolled and consolidated.Mortar
mix ratio should be approved by the engineer .(when AsEph deliver Sand
and Cement)
m3 33 4,500.00 148,500.00
Total carried to summary 188,100.00
4. BLOCK WORK
Block Walls shall be constructed from class 'C' hollow concrete block (H.C.B.).
The blocks shall be seleted for their consistency in dimiensions, shapes, angles
and strength,
They should be free from craks or any other defects and the surface charaterstics
of the blocks shall be in such a way that good gripping capacity for plastering on
both side. Price shall include window/door lintel work. The HCB blocks shall be
tested on site or in the labratory based on the requirements of the Engineer
supply and instal 20cm HCB wall with design compresive strength,bedded in
4.1 cement mortal 1:3 m2 440.00 850.00 374,000.00
supply and instal 15 cm HCB wall with design compresive strength,bedded in
4.2 cement mortal 1:3 m2 88.00 850.00 74,800.00
Total carried to summary 448,800.00
Project: G+0
Owner : Ethiopan Government
Location: Addis Ababa,Ethiopia
item no Description Unit Quantity Unit rate Amount
5.PLASTERING
Supply, prepare and apply two coats of cement plaster to internal wall, Column
surfaces, Stair soffit, and ceiling surfaces where indicated on the drawings and in
accordance with the technical specifications. The proportioning of the first two
coats (Base Coats) shall be as indicated on the standard specs. Price shall include
pre-cleaning, edge plastering, post cleaning and at the joints of block walls and
concrete surfaces
Apply two coats of plastering in cement mortar (1:3) include exposed surface of
beams and columns (external and internal wall surfaces )The work & cost
included all the necessary workmanship & materials. concrete structure joints
shall be well treated to avoid hairline crakes. (Cement and sand will be
supplied by AsEph)
5.1 m2 440.00 150.00 66,000.00
Fine coat gypsum plaster--with Material
Supply and apply Gypsum plastering over the smoothed & drayed plastering
surface of ceiling, soffit & stair landing, wall & columns (Internal). The gypsum
surfaces left until it becomes cure before paint applied on it. The work & cost
included all the necessary workmanship & materials.
5.2 m2 440.00 140.00 61,600.00
Total carried to summary 127,600.00
6. PAINTING---with material
Apply three coats of Varnish paint to the internal masonary wall. Finally clean all
areas affected by painting, washing, and paint removal mechanisms and polishing
surface to ensure that no paint marks are left on the affected areas. Price shall
include all services and materials of pre cleaning and preparation of the surface
(internal wall surfaces)
Apply three coats of plastic emulsion paint to internal walls as per the given
architectural drawing. Surfaces shall be clean by removing grease, dust or any
other alien attachments. Finishing coats shall be applied evenly over the whole
surface to give a solid film free from brush marks, sags, runs, orange peeling or
other defects. All repairs shall be primed before undercoating is applied. Finally
clean all areas affected by painting, washing, and paint removal mechanisms and
polishing surface to ensure that no paint marks are left on the affected areas.
Price shall include all services and materials of pre cleaning and preparation of
the surface (internal wall surfaces)
6.1 m2 440.00 260.00 114,400.00
Total carried to summary 114,400.00
7. Roofing. ----only Labor
Deploy all qualified manpower and Eqeipments as per the order from the
7.1 Enginner m2 320.00 300.00 96,000.00
Total carried to summary 96,000.00
