U893BSE
1.3 GHz Prescaler for PLL’s in TV, CATV and SAT TV Tuners
Technology: Bipolar
Features
D Extrem low current consumption (typ. 18 mA) D Emitter follower output stage
D Output harmonics strongly reduced D Electrostatic protection according to MIL–STD. 883
D 3 scaling factors 64/128/256 programmable at Pin 5
D Pin compatible to U833BSE
D High input sensitivity
Case
8 pin dual inline plastic (U893BSE)
8 pin SO plastic (U893BSE-FP)
6 pin SIP plastic (U893BSE-SP)
Block Diagram
TELEFUNKEN Semiconductors 1 (7)
Rev. A1, 23-Aug-96
U893BSE
Pin Configuration
Pin Function (DIP8, SO8) Pin Function (SIP6)
1 n.c. 1 Ground
2, 3 Input 2 Switch 64/128/256
4 Ground 3 Output
5 Switch 64/128/256 4 VS
6, 7 Output 5, 6 Input
8 VS
Absolute Maximum Ratings
Reference point Pin 4 (1), unless otherwise specified
Parameters Symbol Value Unit
Supply voltage Pin 8 (4) VS 6 V
Input voltage range Pin 2, 3, 5 (2, 5, 6) Vi 0 to VS V
Junction temperature Tj 125 °C
Ambient temperature range Tamb –25 to +85 °C
Storage temperature range Tstg –40 to +125 °C
Thermal Resistance
Parameters Symbol Maximum Unit
Junction ambient DIP8 RthJA 100 K/W
SIP6 RthJA 100 K/W
SO8 RthJA 175 K/W
Electrical Characteristics
VS = 4.5 to 5.5 V, Tamb = 0 to 70 °C, referred to test circuit, unless otherwise specified
Parameters Test Conditions / Pin Symbol Min. Typ. Max. Unit
Supply voltage range Pin 8 (4) VS 4.5 5.5 V
Supply current VS = 5 V Pin 8 (4) IS 21 25 mA
Input sensitivity 1) RG = 50 W
fi = 70 to 1100 MHz
Pin 2, 3 (5, vi 10 mV
6)
fi = 1100 to 1200 MHz
Pin 2, 3 (5, vi 15 mV
6)
fi = 1200 to 1300 MHz
Pin 2, 3 (5, vi 20 mV
6)
Large signal compatibility RG = 50 W Pin 2, 3 (5, Vi 300 mV
6)
1) RMS-voltage calculated from the measured available power
2 (7) TELEFUNKEN Semiconductors
Rev. A1, 23-Aug-96
U893BSE
Parameters Test Conditions / Pin Symbol Min Typ Max Unit
Frequency
q y range
g fimin 70 MHz
fimax 1300 MHz
Emitter follower output fi ≤ 1000 MHz, CL = 13 pF,
Voltage swing each output SF = 1:64 Pin 6, 7 (3) VO 0.6 0.7 Vpp
Output impedance Pin 6, 7 (3) ZO 200 W
3rd order harmonics fi = 700 to 900 MHz, V O3f
suppression CL = 13 pF, SF = 1:64 20 log
V O1f
Pin 6, 7 (3) –30 dB
Switching voltage for
scalingg factor ((SF)) 1:64 Pin 5 (2) VSF open
1:128 VSF VS – 0.5 V
1:256 VSF 0 0.3 V
Switching
g current VS = 5 V Pin 5 (2)
1:128 VSF = 5 V ISF 150 mA
1:256 VSF = 0 V ISF –150 mA
Test Circuits
TELEFUNKEN Semiconductors 3 (7)
Rev. A1, 23-Aug-96
U893BSE
Output Circuit
Emitter follower output
4 (7) TELEFUNKEN Semiconductors
Rev. A1, 23-Aug-96
U893BSE
Input Sensitivity
Dimensions in mm
TELEFUNKEN Semiconductors 5 (7)
Rev. A1, 23-Aug-96
U893BSE
Dimensions in mm
6 (7) TELEFUNKEN Semiconductors
Rev. A1, 23-Aug-96
U893BSE
Ozone Depleting Substances Policy Statement
It is the policy of TEMIC TELEFUNKEN microelectronic GmbH to
1. Meet all present and future national and international statutory requirements.
2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems
with respect to their impact on the health and safety of our employees and the public, as well as their impact on
the environment.
It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as
ozone depleting substances ( ODSs).
The Montreal Protocol ( 1987) and its London Amendments ( 1990) intend to severely restrict the use of ODSs and
forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban
on these substances.
TEMIC TELEFUNKEN microelectronic GmbH semiconductor division has been able to use its policy of
continuous improvements to eliminate the use of ODSs listed in the following documents.
1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively
2 . Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental
Protection Agency ( EPA) in the USA
3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C ( transitional substances ) respectively.
TEMIC can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain
such substances.
We reserve the right to make changes to improve technical design and may do so without further notice.
Parameters can vary in different applications. All operating parameters must be validated for each customer
application by the customer. Should the buyer use TEMIC products for any unintended or unauthorized
application, the buyer shall indemnify TEMIC against all claims, costs, damages, and expenses, arising out of,
directly or indirectly, any claim of personal damage, injury or death associated with such unintended or
unauthorized use.
TEMIC TELEFUNKEN microelectronic GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany
Telephone: 49 ( 0 ) 7131 67 2831, Fax number: 49 ( 0 ) 7131 67 2423
TELEFUNKEN Semiconductors 7 (7)
Rev. A1, 23-Aug-96
