MOHAVE/BORREGO(HM) > 2010 > G 4.
6 DOHC > Suspension > ECS(Mando) > C1102
Battery Voltage Low
C1102 Battery Voltage Low > General Information
Component Location
General Description
The ALS is the abbreviation for "Auto Leveling System". This ALS system automatically controls the height of a vehicle level
according to road condition. So it improves riding comfort and steering stability. Among components of the ALS system, a battery
has the role of supplying of electric power to compressor and ALS ECU. And the ALS ECU monitors the battery voltage in order to
control this system normally.
DTC Description
The ALS ECU monitors the voltage of battery and if it stays below certain value, this DTC is set.
DTC Detecting Condition
Item Detecting Condition Possible Cause
DTC Strategy • Monitoring the voltage of battery
• When Battery voltage is below 9.5V during over 5 seconds
( The vehicle speed is more than 35 km/h.)
- In a case that it rises above 10V, the system returns to • Open or short to ground in the
Threshold value
normal. power supply circuit
• When Battery discharges (The DTC is set by the corrent • Faulty ALS ECU
fault)
• Inhibition of controlling a vehicle level
Fail-Safe
• The warning lamp is activated.
Specifications
IGN "ON" or Engine "ON"
Normal Voltage Range
10V ~ 16V
Diagnostic Circuit Diagram
C1102 Battery Voltage Low > Scantool Diagnostics
Monitor Scantool Data
1. Connect scantool to Data Link Connector(DLC).
2. IG ON or Engine ON
3. Monitor the "BATTERY VOLTAGE" parameter on the scantool.
Specifications : 10 ~ 16 V(IGN ON or Engine ON)
Fig 1) Normal data at the IG "ON"
4. Is the battery voltage normal?
▶ Fault is intermittent caused by poor connection in ALS ECU's connector or was repaired and ALS ECU
memory was not cleared. Thoroughly check connectors for looseness, poor connection, bending, corrosion,
contamination, deterioration, or damage.
▶ Repair or replace as necessary and then go to "Verification of Vehicle Repair" procedure.
▶ Go to "Terminal and Connector Inspection" procedure.
C1102 Battery Voltage Low > Inspection/Repair > W/Harness Inspection
Terminal and Connector Inspection
1. Many malfunctions in the electrical system are caused by poor harness(es) and terminal condition.
Faults can also be caused by interference from other electrical systems, and mechanical or chemical damage.
2. Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration, or damage.
3. Has a problem been found?
▶ Repair as necessary and then go to "Verification of Vehicle Repair" procedure.
▶ Go to "Alternator Output Voltage Inspection" procedure.
Alternator Output Voltage Inspection
■ Check charging system
1. Start Engine.
2. Maintain ENG RPM 2,500RPM over 2 minutes.
3. Measure voltage between the battery terminal(+) and the battery terminal(-).
Specification : 10 ~ 16V
4. Is the measured value within specifications?
▶ Go to "Power Circuit Inspection" procedure.
▶ Check that the tension of drive belt, ENG RPM, fuse, terminal of battery, all terminals of alternator are in
good condition and Check for damaged harness and poor connection between alternator and battery.
▶ If OK, repair or replace alternator and then go to "Verification of vehicle Repair" procedure.
Power Circuit Inspection
■ Check for open or short
1. IG "ON" & Engine "OFF"
2. Measure voltage between the battery terminal(+) and power terminal of the ALS ECU harness connector.
Specification : Approx. below 0.2V
3. Is the measured value within specifications?
▶ Go to "Ground Circuit Inspection" procedure.
▶ Check for open or blown fuse referring to "Circuit Diagram".
▶ Repair open or short in power circuit between battery and ALS ECU harness connector and then go to
"Verification of vehicle Repair" procedure.
Ground Circuit Inspection
■ Check for open or short
1. IG "OFF".
2. Disconnect ALS ECU connector.
3. Measure resistance between ground terminal of the ALS ECU harness connector and chassis ground.
Specification : Approx. below 1Ω
4. Is the measured value within specifications?
▶ Substitute with a known-good ALS ECU and check for proper operation.
If problem is corrected, replace ALS ECU and then go to "Verification of Vehicle Repair" procedure.
▶ Repair open or short in ground circuit between ALS ECU harness connector and chassis ground, and
then go to "Verification of vehicle Repair" procedure.
C1102 Battery Voltage Low > Verification of Vehicle Repair
Verification of Vehicle Repair
After a repair, it is essential to verify that the fault has been corrected.
1. Connect scantool and select "Diagnostic Trouble Codes(DTCs)" mode
2. Using a scantool, Clear DTC.
3. Operate the vehicle within DTC Detecting Condition in General Information.
4. Using a scantool, Check DTC present.
5. Are any DTCs present ?
▶ Go to the applicable troubleshooting procedure.
▶ System performing to specification at this time.
C1102 Battery Voltage Low > 회로도 입력
Schematic Circuit Diagram
