JTO Telecom 2009

[Link]

JTO

Section-1 Q. 1-20 Carry One Mark Each

Q.1

Q -meter works on the principle of (B) parallel resonance (D) self inductance

(A) series resonance (C) mutual inductance

Q.2

The bridge circuit shown in Fig.Q.2-I

(A) cannot be balanced (B) can be balanced but the frequency of excitation must be known (C) can be balanced for only one frequency (D) can be balanced at any frequency Which one of the following statements is TRUE for an ideal power diode?

Q.3

(A) Forward voltage drop is zero and reverse saturation current is non-zero. (B) Reverse recovery time is non-zero and reverse saturation current is zero. (C) Forward voltage drop is zero and reverse recovery time is zero. (D) Forward voltage drop is non-zero and reverse recovery time is zero. In a MOSFET, the pinch-off voltage refers to

Q.4

(A) drain-to-source voltage at which drain-to-source current is zero. (B) gate-to-source voltage at which gate-to-source current is zero. (C) drain-to-source voltage at which gate-to-source current is zero. (D) gate-to-source voltage at which drain-to-source current is zero.

JTO

1/28

JTO Telecom 2009

Q.5

[Link]

JTO

Which of the following statement is TRUE for DC switched mode power supply?

(A) In cannot provide isolation between input and output as in rectifiers. (B) It cannot remove ripple as in DC switching mode regulators. (C) It has two state conversions: dc-ac and ac-dc. (D) It is a type of chopper circuit. Which one of the following is a ceramic insulator? (B) Porcelain (D) Synthetic fiber

Q.6

(A) Mica (C) Liquid crystal

Q.7

Which one of the following represents a direct band-gap material? (B) Ge (D) GaAs

(A) Si (C) GaP

Q.8

Which one of the following statements is NOT true?

(A) Rochelle salt exhibits ferroelectric property (B) Spontaneous polarization is a characteristic property of ferroelectric material. (C) Spontaneuos polarization of ferroelectric (D) Ferroelectric materials exhibit hysteresis effect. Which one of the following diodes contains a metal-semiconductor junction? (B) Zener diode (D) Gunn diode

Q.9

(A) Tunnel diode (C) Schottky diode

Q.10

Which one of the following statements is NOT true?

(A) Ferrites can be used in transformer cores only at very low frequencies. (B) Ferrites are ferrimagnetic material. (C) Ferrites show spontaneous magnetization below certain temperature (D) DC resistivity of ferrites is many orders of ten higher than that of iron.

JTO

2/28

JTO Telecom 2009

Q.11

[Link]

JTO

Which one of the following statements is NOT true?

(A) In an intrinsic semiconductor, concentration of electrons in the conduction band is same as the concentration of holes in the valance band. (B) The probability of an energy state at the Fermi level being occupied by an electron is 1/2. (C) Mobility of electrons is higher than that of holes. (D) In an n -type semiconductor, concentration of holes is equal to that of the intrinsic concentration. V1 A B V2 . ABCD parameters of a two-port network is defined as > H = > I1 C DH> I2H If the port-2 is terminated by a resistance RL , the admittance looking into the port-1 is (B) CRL + D ARL + B (D) C + DRL ARL + B

Q.12

(A) C + DRL A + BRL (C) CRL + D A + BRL

Q.13

The phenomenon of injection electroluminescence is the basis of working of (B) light emitting diodes (D) solar cells

(A) photodiodes (C) phototransistors

A parallel combination of N resistances is connected across an ideal current source of I Amperes. The expression for the current in the kth resistor Rk is
Q.14

Rk (A) b I R1 + R2 + .... + RN l (C) Rk I f 1 + 1 + .... + 1 p Rk R 2 RN

J N 1 K O Rk (B) K OI K 1 + 1 + .... + 1 O RN P L R1 R 2 1 (D) Rk f pI R1 + R2 + .... + RN

Q.15

In the circuit shown in Fig.Q15-I, the voltage across the terminals AB (in volt) is

JTO

3/28

JTO Telecom 2009 (A) 5/30c (C) 17/30c

[Link] (B) 12.5/30c (D) 25/30c

JTO

Q.16

A half wave (i.e., /2 ) lossless transmission line of characteristic impedance Z 0 is terminated to a load of impedance ZL as shown in the Fig. Q16-I. The input impedance as seen at the other end is

(A) ZL Z0 (C) ZL Z 0

(B) ZL
2 (D) Z L Z0

Q.17 A microstrip line has a strip width W and a grounded dielectric substrate of thickness d and relative permittivity r . Which one of the following statements is NOT true?

(A) The effective dielectric constant eff satisfies 1 < eff < r . (B) The effective dielectric constant eff is a function of W d (C) The characteristic impedance of the line is a function of W d (D) The line can support pure TEM mode of wave propagation. For a rectangular waveguide of internal dimensions a cm # b cm , a > b , the mode of wave propagation with the lowest cut off frequency is (A) TE 01 (C) TE11
Q.19

Q.18

(B) TE10 (D) TM11

The most appropriate value (in ) of the radiation resistance of a quarter wave monopole antenna is (A) 36.5 (C) 73 (B) 50 (D) 120

Q.20

Which one of the following is an active transducer? 4/28

JTO

JTO Telecom 2009 (A) Photo-voltaic cell (C) Photo-emissive cell

[Link] (B) Strain gauge (D) Synchro

JTO

Q. 21-50 Carry Two Marks Each

Q.21

A 0.1 A ammeter having a resistance of 10 is to be converted to a 1 A ammeter by using a shunt resistance. Which one of the followings is the most appropriate shunt resistance? (A) 0.1 (B) 1.0 (D) 1.2

(C) 1.1
Q.22

The forward voltage drop of a power diode is VD = 1.0 V at the diode current ID = 200 A . Assuming the emission coefficient = 2 and thermal voltage VT = 25.7 mV , the reverse saturation current IS (approximate) is (A) 71.08 A (C) 21.09 A (B) 51.20 A (D) 41.09 A

Q.23 In the circuit shown in Fig.Q23-I, the voltage across 25 k resistor is to be measured by using a voltmeter of sensitivity of 1 k/V . The magnitude of percentage error in the measurement is

(A) 10 (C) 30

(B) 20 (D) 40

Q.24

Fig.Q24-I shows some load voltage versus load current plots. Which one of them is NOT valid for the classification of dc-dc converters?

JTO

5/28

JTO Telecom 2009

[Link]

JTO

(A) P (C) R

(B) Q (D) S

Q.25

Two single phase inverters, one half-bridge and the other full-bridge, operating with equal inputs delivering power to identical loads. The ratio of, the power delivered, the first harmonic voltage and the total harmonic distortion, for full-bridge inverter to half-bridge inverter, respectively, are (A) 4, 2, 1 (C) 4, 1, 1 (B) 4, 2, 2 (D) 2, 1, 1

Q.26

The correct match between Column A and Column B is Column B R. Inverter S. MOSFET P. Boost Converter Q. Cycloconverter (B) 1-S, 2-P, 3-Q, 4-R (D) 1-S, 2-Q, 3-P, 4-R

Columa A 1. DC Switch 2. Regulated DC-DC 3. AC to AC 4. DC to DC (A) 1-R, 2-Q, 3-P, 4-S (C) 1-P, 2-R, 3-Q, 4-S

Q.27

For the power transistor circuit shown in Fig.Q27-I, VCE (sat) = 1.0 V,VBE (sat) 1.5 V and 6/28

JTO

JTO Telecom 2009

[Link]

JTO

= 9 . With an overdrive factor of 2.5, the required resistance RB for saturation is

(A) 2.73 (C) 17

(B) 6.83 (D) 22.5

Q.28 For a lossless air filled cubical cavity of internal dimension 5 cm on each sides, the resonant frequency for the TE101 mode is

(A) 5 2 GHz (C) 3 2 GHz

(B) 5 GHz (D) 3 GHz

Q.29

Which one of the following statements is NOT true?

(A) For SCRs to be in the conduction state, the forward anode current must be greater than the latching current. (B) For SCRs to be in the forward blocking state, the forward anode current must be lower than the holding current. (C) When SCRs are in the conduction state, they can be turned off by applying suitable gate pulses. (D) When avalanche breakdown takes place, SCRs enter into the conduction state. Consider two metallic wires W1 and W2 . They are made up of same material and each has circular cross section. The diameter of W2 is twice that of W1 and the length of W2 is four times that of W1 . Which one of the following statement is TRUE?
Q.30

(A) Resistance of W1 is half that of W2 (B) Resistance of W1 is equal to that of W2 (C) Resistance of W1 is twice that of W2 (D) Resistance of W1 is eight times that of W2

JTO

7/28

JTO Telecom 2009

Q.31

[Link]

JTO

A current of 1 A flows through a circular loop of superconducting wire having mean diameter of 1 m, cross section area of 1 mm2 and self inductance of 4 # 107 H . The current reduces to 0.99 A after 1 year. The resistivity of the wire is (A) 1.275 # 1026 m (C) 1.275 # 1024 m (B) 1.275 # 1025 m (D) 1.275 # 1023 m

Q.32 An npn transistor is operating in CE mode and carries a collector current Ic = 1 mA when the collector to emitter voltage VCE = 1 V . If the early voltage for the transistor is 74 V and base to emitter voltage VBE is kept constant, at VCE = 11 V the collector current is

(A) 15/19 mA (C) 19/15 mA

(B) 1 mA (D) 19/12 mA

Two parallel plate capacitors shown in fig. Q33-I (a) and Fig.Q33-I (b) have capacitances C1 and C2 , respectively. If C2 = 2C1 , which one of the following relations is TRUE? (Neglect fringing effect)
Q.33

(A) x = L 4 (C) x = L 3
Q.34

(B) x = L 2 (D) x = 2L 3

A doped semiconductor specimen has Hall coefficient 3.6 # 104 m3 C1 and the resistivity 9 # 103 m . Assuming single carrier conduction, the mobility and density of carriers in the specimen, respectively, are (approximately) (A) 0.04 m2 V1 s1 and 1.74 # 1022 m3 (B) 0.4 m2 V1 s1 and 1.74 # 1022 m3 JTO 8/28

JTO Telecom 2009

[Link]

JTO

(C) 0.04 m2 V1 s1 and 1.74 # 1018 m3 (D) 4.0 m2 V1 s1 and 1.74 # 108 m3
Q.35 If n, n i, p n , and p , respectively denote electron concentration, intrinsic concentration, mobility of electrons intrinsic concentration, mobility of electrons and mobility of holes, the minimum conductivity of a semiconductor sample occurs at

(A) n = ni (C) n = ni
Q.36

p n n p

(B) n = ni (D) n = ni

n p p + n

GaAs has bandgap energy of 1.42 eV. The material would produce photon output at a wavelength of (Planck s constant = 6.625 # 1034 J s , q = 1.6 # 1019 C ) (B) 0.653 m (D) 0.953 m

(A) 0.553 m (C) 0.875 m

Q.37 At a frequency of 1 GHz, the equivalent inductance between the terminals of a /8 ( represents wavelength) short-circuited lossless 50 line is)

(A) 5/ nH (C) 25/ nH

Q.38

(B) 15 nH (D) 50/ nH

For the circuit shown in Fig.Q38-I, the transistor parameters are VBE = 0.7 V , = 99 . If VC is to be set at 7.5 V, the required value (in k) of RB is

(A) 172 (C) 100

(B) 136 (D) 82

JTO

9/28

JTO Telecom 2009

Q.39

[Link]

JTO

A quarter wave matching transformer is used to match a 30 load to a line having characteristic impedance 120 . The characteristic impedance of the quarter wave matching section is (A) 50 (C) 120
Q.40

(B) 60 (D) 150

If the average power delivered to a load terminated to a lossless transmission line is 75% of that of the incident power, the VSWR on the line is (A) 1/3 (C) 2 (B) 1 (D) 3

Q.41

For the circuit shown in Fig.Q41-I, a value of R (in ), to which the voltage source would deliver 50% of the maximum deliverable power, is

(A) 1 (C) 0.25

(B) 0.5 (D) 38

Q.42

In the circuit shown in Fig. Q 42-I (a), the current I1 = 2 A . The current I2 in Fig. Q42-I (b) is

(A) 6 A (C) 4 A JTO

(B) 4 A (D) 6 A 10/28

JTO Telecom 2009

Q.43

[Link]

JTO

In the circuit shown in Fig.Q43-I, the current I through 2 resistor is

(A) 94.34 mA (C) 70.34 mA

(B) 70.34 mA (D) 94.34 mA

Q.44

For the circuit shown in Fig.Q44-I, the Thevenins voltage and resistance at terminals A and B, respectively, are

(A) 8 V and 5 k (C) 4 V and 5 k

(B) 8 V and 10 k (D) 4 V and 10 k

Q.45

In the circuit shown in Fig.Q45-I, the switch closes at t = 0 . Assuming steady state condition for t = 0 , the current iL at t = 0.15 sec is (approximately)

(A) 0.04 A (C) 0.76 A

(B) 0.5 A (D) 1.60 A

Q.46 A PMMC instrument has a coil of dimensions 10 mm # 10 mm and the flux density in the air gap is 2 mW/m2 . The coil has 100 turns. If a current of 5 mA produces an angular deflection of 90c, the spring constant of the instrument is

JTO

11/28

JTO Telecom 2009 (A) 2 # 108 N m/rad (C) # 108 N m/rad

Q.47

[Link] (B) # 108 N m/rad 2 (D) 1 # 108 N m/rad

JTO

In the circuit shown in Fig.Q47-I, assume the diodes are ideal and the ammeter is an average indicating meter with zero internal resistance. The ammeter reading is

(A) 0.4 mA (C) 0.4 mA 2

Q.48

(B) 0.8 mA (D) 0.8 mA 2

A capacitive transducer uses two quartz diaphragms of area 550 mm2 each separated by a distance of 3.7 mm. A pressure of 750 kN/m2 applied to the top diaphragm produces a displacement of 0.7 mm. The capacity is 390 pF when no pressure is applied to the diaphragm. The value of the capacitance after the application of pressure of 750 kN/m2 is (A) 400 pF (C) 481 pF (B) 451 pF (D) 500 pF

A thermistor has a resistance of 500 at 30c C and has a temperature coefficient of 5 /cC . This thermistor is used to measure the temperature of a system by the arrangement shown in Fig.Q49-I. If the system temperature falls to 20c C , the VAB measured by the voltmeter is
Q.49

JTO

12/28

JTO Telecom 2009 (A) 10/29 V (C) 10/29 V

[Link] (B) 15/29 V (D) 15/29 V

JTO

Q.50

For the circuit shown in Fig. Q50-I, if the current I = 3 A , then the voltage V2 is

(A) 2.5 V (C) 8 V

(B) 5 V (D) 10 V

Section-2 Q. 1-20 Carry One Mark Each

Q.1

Which one of the following statements is NOT true for a TWT?

(A) The interaction region usually consists of a slow wave helix structure (B) A static axial magnetic field keeps the electron beam focused. (C) Continued interaction takes place between the waves on a traveling wave structure and the electron beam. (D) TWT amplifiers are suitable only for narrowband microwave communication systems. The minimized form of the Boolean expression F (A, B, C) = (0, 2, 3) is (B) A + BC (D) ABC + AB

Q.2

(A) A + BC (C) AC + B
Q.3

Number of address lines required to address 8 k bytes of memory is (B) 14 (D) 16

(A) 13 (C) 15

Q.4

The standard binary code for alpha numeric characters is

JTO

13/28

JTO Telecom 2009 (A) ASCII (C) BCD

[Link] (B) GRAY (D) Excess-3

JTO

Q.5

The 2s complement of the binary number 1101100 in BCD is (B) 13 (D) 15

(A) 12 (C) 14

Q.6

In the op-amp circuit shown in Fig.Q6-II, the voltage ratio V0 /Vi is

(A) 2 (C) 0.5

Q.7

(B) 1 (D) 0.5

For the Schmitt trigger circuit shown in Fig. Q7-II, assuming diodes and op-amp are ideal, the values of lower and upper threshold points of voltage transfer characteristics, respectively, are

(A) 8 V, + 5 V (C) 5 V, + 8 V JTO

(B) 5 V, + 5 V (D) 8 V, + 8 V 14/28

JTO Telecom 2009

Q.8

[Link]

JTO

Which one of the following Boolean expression is NOT correct? (B) x + y = x y (D) x y = x + y

(A) x + y = x y (C) x y = x + y
Q.9

A Boolean function can be expressed

(A) as sum of maxterms or product product of minterms (B) as product of maxterms or sum of minterms (C) partly as product of maxterms and partly as sum of minterms (D) partly as sum of maxterms and partly as product of minterms Among the following logic families, the one having the lowest power dissipation and highest noise margin is (A) Schottky TTL (C) ECL (B) TTL (D) CMOS

Q.10

Q.11 The characteristic equation of a level triggered T flip-flop, with T as input and Q as output is

(A) Q (n + 1) = TQ + TQ (C) Q (n + 1) = Q
Q.12

(B) Q (n + 1) = T (D) Q (n + 1) = TQ + T Q

The Nyquist plot of G (j) H (j) of a closed loop control system encloses the point ( 1, j0) in GH-plane. The gain margin of the system in dB, is (A) greater than zero (C) zero (B) less than zero (D) infinite d 2 y (t) dy (t) +3 + 4y (t) = r (t) + 2r (t 1) and 2 dt dt Y (s) is R (s)

Q.13

For the LTI system described by 2

having zero initial conditions, the transfer function (A) 1 + 2es 2s2 + 3s + 4

2 (B) 2s + 3s + 4 1 + 2es

JTO

15/28

JTO Telecom 2009 (C) 1 + 2es 2s2 + 3s + 4

[Link]
2 + (D) 2s + 3s s 4 1 + 2e

JTO

An amplitude modulated double sideband suppressed carrier signal is given by [1 + am cos 2fa t] cos 2fm t cos 2fc t , where fc is the frequency of the carrier signal. The modulating signal is
Q.14

(A) am cos 2fa t (C) [1 + am cos 2fa t] cos 2fm t

Q.15

(B) am cos 2fa t cos 2fm t (D) 1 + am cos 2fa t

Which one of the following expressions represents a frequency modulated signal?

(A) Ac cos 2 [fc t + m (t)] (C) Ac m (t) cos 2fc t

Q.16

#0 m () dD cos 2fc t t (D) Ac cos 2 :fc t + # m () dD 0

t

(B) :1 +

A binary pulse communication system transmits a normalized pulse p (t) over bit duration Tb . If the pulse p (t) has Fourier transform P (f), the condition for zero intersymbol interference in the absence of noise is (A) (C) Pa f n k = 1 T0 n = 3

/
3

(B) (D)

P a f n k = Tb Tb n = 3

Pa f n k = 1 Tb Tb n = 3

n=0

n / Pa f Tb k = Tb

Q.17

The magnitude response of an ideal equalizer for rectifying a distortion characterized by T sin c (fT) ejfT is (B) T/ sin c (fT) (D) sin (fT) /T

(A) T sin c (fT) (C) f/ sin (fT)

Q.18

If the minimum sampling frequency required to reconstruct a band limited analog signal from its samples is 8 kHz, the maximum frequency present in the signal is (B) $ 16 kHz (D) > 4 kHz

(A) 16 kHz (C) 4 kHz

Q.19

Which one of the following statements is NOT true?

(A) The two cavity klystron tube is used as an amplifier (B) A reflex klystron uses only a single cavity and operates as an oscillator. JTO 16/28

JTO Telecom 2009

[Link]

JTO

(C) In klystron tubes, the bunching of electrons is caused by velocity modulation. (D) Klystrons belong to the category of crossed-field tubes. In a microprocessor, the program counter points to the address location from where (B) next byte is to be fetched (D) current byte is to be added

Q.20

the (A) current byte is to be fetched (C) next byte is to be stored

Q. 21-50 Carry Two Marks Each

Q.21 A microwave link operates under free space conditions at a frequency of 1 GHz and uses identical antennas at the transmitter and the receiver ends. The transmitter and the receiver are separated by a distance of 30 km. If 30 dBm power is to be received when the transmitted power is 1 W, the antenna gain should be

(A) 100 (C) 300

(B) 200 (D) 400

Q.22

In connection with memory mapped 110 which one of the following statements is NOT true? (A) The processor treats an interface register as a part of the memory system. (B) It reduces the memory space available. (C) The processor cannot manipulate I/O data residing in interface registers with the same instructions that are used to manipulalte memory location. (D) Arithmetic or logical operation can be directly performed with I/O data. After execution of the following C program, the value of the sum printed is

Q.23

main () { int i, n; oat x, dx, sum; sum = 0; x = 2; for (i=1; i<=100; i++) { dx = x*(i-1); JTO 17/28

JTO Telecom 2009 sum = sum + dx; x = 2*x; if (sum > x) break; } printf(%f, sum); end; } (A) 68 (B) 16

[Link]

JTO

(B) 20 (D) 4

Q.24

If selection sort takes 3 ms to run an array of 200 elements, for a similar array of 4000 elements the selection sort is expected to take (A) 1.2 s (C) 300 ms (B) 600 ms (D) 60 ms

In a stack based processor organization, postfix notation is used for evaluating arithmetic expressions. The postfix expression ABC )/D EF/ + for A = 6, B = 2, C = 3, D = 3 , E = 4 and F = 2 evaluates to
Q.25

(A) 0 (C) 2

(B) 1 (D) 3

Q.26

In a 8085 microprocessor system, the active low chip select (CS) signal is generated by passing address lines A15, ....., A10 through a 6 inputs NAND gate. For selecting the address range CC00 to CFFF , the inputs to the NAND gate are (A) A10, A11, A12, A13, A14, A15 (B) A10, A11, A12, A13, A14, A15 (D) A10, A11, A12, A13, A14, A15

(C) A10, A11, A12, A13, A14, A15

Q.27

in the context of 8085 microprocessor, the correct matching combination between Column A and Column B is Column A P. ALE Q. PSW R. CMA S. RLC JTO Column B 1. Rotate accumulator left 2. Compare with accumulator 3. Program status word 4. Address latch enable 18/28

JTO Telecom 2009

[Link] 5. Program stack work 6. Arithmetic logic enabled 7. Complement accumulator 8. Rotate accumulator left through carry

JTO

(A) P-6, Q-5, R-2, S-8 (C) P-4, Q-3, R-7, S-1

(B) P-4, Q-3, R-2, S-8 (D) P-6, Q-5, R-7, S-1

Q.28

The content of the memory location 2070 H after the execution of the following 8085 program is LXIB MVI MVI SUB ANI STAX HLT (A) 04 H (C) 09 H 2070H A, 8FH C, 68H C OFH B (B) 07 H (D) 0F H

Q.29

A 8085 microprocessor program uses all available Jump instructions, each only once. For this program, the total, memory (in Bytes) occupied by the Jump instructions is (A) 30 (C) 24 (B) 27 (D) 18

Q.30

The circuit shown in Fig.Q30-II oscillates at an angular frequency of at a particular R. The values of (in rad/sec) and R ( in k), respectively, are

JTO

19/28

JTO Telecom 2009

[Link]

JTO

(A) 105 and 20 (C) 2 # 105 and 10

(B) 2 # 105 and 20 (D) 105 and 10

Q.31

A combinational circuit accepts a 2 bit binary number and outputs its square in binary. To design this circuit using a ROM, the minimum size of ROM required is (A) 2 # 2 (B) 4 # 2 (D) 8 # 4

(C) 4 # 4

In the op-amp circuit shown in Fig. Q32-II, assume the diode current follows the equation I = Is eV/V . If V0 = V0 for Vi = 2V and V0 = V0 for Vi = 4V , the relation between V0 and V0 is
Q.32
T 1 2 1 2

(A) V0 = V0
2 2

(B) V0 = V0 e2
2 1

(C) V0 = V0 ln 2
1

(D) V0 = V0 + VT ln 2
2 1

Q.33

In the 2-stage amplifier circuit shown in Fig.Q33-II, if the transconductances of transistor Q 1 and transistor Q 2 are gm1 and gm2 , respectively, the overall transconductances gm0 = i 0 /vi of the amplifier is

JTO

20/28

JTO Telecom 2009

[Link]

JTO

(A) gmo . gm1 (C) gmo = gm1 + gm2

(B) gmo . gm2 (D) gmo = gm1 gm2

K (s + 4) For the system with G (s) H (s) = , the breakway points in the root-loci plot s (s + 1) approximately are
Q.34

(A) 7.46, 1 (C) 7.46, 0.54

Q.35

(B) 0.54, 1 (D) 7.46, 0.54

For the circuit shown in fig. Q35-II, the p-channel, JFET transistor parameters are IDSS = 6 mA and VP = 4 V . The source-to-drain voltage VSD and the region of operation of the transistor, respectively, are

(A) 2.09 V and active region (B) 2.47 V and active region

(B) 2.09 V and saturation region (D) 2.47 V and saturation region

Q.36

For the truth table given in Fig.Q36-II, the minimized Boolean expression is x 0 0 0 Input y 0 0 1 z 0 1 0 Output p 1 0 0 21/28

JTO

JTO Telecom 2009 0 1 1 1 1 (A) p = xyz + xyz + xy z + x yz (C) p = x (y 5 z) + x (y 5 z)

Q.37

[Link] 1 0 0 1 1 1 0 1 0 1 (B) p = x 5 y 5 z (D) p = x 5 y 5 z 1 0 1 1 0

JTO

For a linear system having the characteristic equation s 4 + s3 + 2s2 + 2s + 3 = 0 , the number of roots in the right half of s -plane is (A) 4 (C) 2 (B) 3 (D) 1

The Boolean function F (A, B, C) = (0, 2, 4, 7) is to be implemented using a 4 # 1 multiplexer shown in Fig.Q.38-II. Which one of the followign choices of inputs to multiplexer will realizer the Boolean function?
Q.38

(A) (I 0, I1, I2, I 3, s1, s 0) = (1, 0, A, A, C, B) (B) (I 0, I1, I2, I 3, s1, s 0) = (1, 0, A, A, B, C) (C) (I 0, I1, I2, I 3, s1, s 0) = (0, 1, A, AC, B) (D) (I 0, I1, I2, I 3, s1, s 0) = (0, 1, A, A, B, C)
Q.39

An edge triggered synchronous binary counter is provided with a clock (CLK) and control inputs: active low clear (CLR ), active high load (L) and active high count (C). The correct matching combination between Column A and Column B is Column A Column B 1. No change 2. Load inputs 3. Count next binary state 22/28

a. (CLK, CLR, L, C) = (-, 1, 1, X) b. (CLK, CLR, L, C) = (-, 1, 0, 1) c. (CLK, CLR, L, C) = (X, 0, X, X) JTO

JTO Telecom 2009 d. (CLK, CLR, L, C) = (X, 1, 0, 0) (A) (B) (C) (D)
Q.40

[Link] 4. Clear outputs

JTO

a 2 1 2 1

b 3 2 3 2

c 4 3 1 4

d 1 4 4 3

A 5-bit serial adder is implemented using two 5-bit shift registers, a full adder and a D flip-flop. The two binary words to be added are 11011 and 11011. The sum of the two numbers is stored in one of the shift registers and the carry in the D flip-flop. Assuming that the D flip-flop is set initially, the content of the sum shift register and the D flip-flop, respectively, are (A) 10111 and 0 (C) 11101 and 0 (B) 11011 and 1 (D) 10111 and 1 Y (s) is R (s)

Q.41

For the flow diagram shown in Fig.Q41-II, the transfer function

(A) (C)

3 s2 + 6s + 11 3 s2 + 6s + 8

(B) (D)

3 s2 + 5s + 4 3 s2 + 6s + 11

The compensated system shown in Fig.Q42-II, has a phase margin of 60c at the crossover frequency of 1 rad/sec. The value of K is
Q.42

(A) 0.366 (C) 1.366

(B) 0.732 (D) 2.732

JTO

23/28

JTO Telecom 2009

Q.43

[Link]

JTO

A time division multiplex system samples 96 voice channels at a rate of 8 kHz and encodes into 8 bits per sample. If one synchronization bit per frame is added, the transmitted data rate (Mbps) is (A) 6.208 (C) 6.144 (B) 6.152 (D) 0.768

Q.44

A geostationary satellite located at 36,000 km from the surface of the earth. The uplink free space loss is 1.583 dB higher than the downlink free space loss. If the downlink frequency is 10 GHz, the uplink free space loss (in dB) is (A) 10.25 (C) 102.5 (B) 20.5 (D) 205

Q.45

In a uniform quantizer, the quantization noise is

(A) independent of the number of levels of the quantizer. (B) proportional to square of the peak-to-peak voltage range of the quantizer. (C) independent of the peak-to-peak voltage range of the quantizer. (D) proportional to square of the number of levels of the quantizer. In a digital communication system, the transmitted pulse is shown in Fig Q46-II .The matched filter output at the sampling instant (i.e., t = 1 sec ) is

Q.46

(A) (C) 1 2
Q.47

3 2

(B) 1 (D) 1 6

An optical link uses a fiber having a power loss of 1 dB/km. A typical photo detector has responsively 0.5 A/W. If the link is 3 km long and the detector is required to produce a current of 25 A , the required transmitted power is JTO 24/28

JTO Telecom 2009 (A) 0 dBm (C) 30 dBm

Q.48

[Link] (B) 10 dBm (D) 50 dBm

JTO

For the directional coupler shown in Fig.Q48-II, the coupling is 20 dB and the directivity is 30 dB. If 10 W power is incident in port-1, power out of port-4 is

(A) 0.1 mW (C) 0.01 W

(B) 1 mW (D) 0.1 W

In a microwave measurement with slotted rectangular waveguides, the distance between successive minima is found to be 2.5 cm. If the measurement has been carried out at a frequency of 10 GHz and the guide operates in TE10 mode, the cut off frequency fc10 for the guide is
Q.49

(A) 6 GHz (C) 10 GHz

(B) 8 GHz (D) 12 GHz

Q.50

An antenna having a directivity of 2 at a frequency of 300 MHz will have a maximum effective aperture of (A) 1 m2 8 (B) 1 m2 4 (D) 1 m2

(C) 1 m2 2

Section-3 Q. 1-20 Carry One Mark Each

Q.1

Chandrayaan-I, Indias first mission to the moon, has 11 scientific instruments that are being released on the surface of the moon. These instruments are together known as (A) Moon Impact Probes (C) Scientific Payloads (B) Terrian Mapping Cameras (D) Spectrometers

JTO

25/28

JTO Telecom 2009

Q.2

[Link]

JTO

The World Wide Web was invented by (B) Narayanmurthy (D) Charles Babbage

(A) Tim Berners-Lee (C) Sabeer Bhatia

Q.3

How many diagonals does a quadrilateral have? (B) two (D) four

(A) One (C) four ISO 14000 standards deal with

Q.4

(A) quality management (C) human resorece management

(B) production management (D) enviromental management

Q.5

Which Indian politicians autobiography is titled The Story of My Life? (B) Mahatma Gandhi (D) Atal Behari Vajpayee

(A) Morarji Desai (C) Lal Krishna Advani

Q.6

The phrase through thick and thin means (B) thin and fat (D) under all conditions

(A) big and small (C) large object Picturesque means

Q.7

(A) Photogenic (C) Stimulating Diligent means

(B) Simple (D) Ugly

Q.8

(A) intelligent (C) modest The opposite of miserly is

(B) energetic (D) industrious

Q.9

(A) spendthrift JTO

(B) generous 26/28

JTO Telecom 2009 (C) liberal The opposite of ingratitude is

[Link] (D) charitable

JTO

Q.10

(A) sympathy (C) thankfulness

(B) reward (D) stimulation

Q.11

The appropriate missing word in the blank space in the sentence I prefer coffee ................tea. is (A) than (C) for (B) over (D) to

Q.12

The appropriate missing word in the blank space in the sentence Many relatives attended him during his illness. (A) of (C) for (B) on (D) with

Q.13

The article required before the word one-eyed in the sentence There was ................. one-eyed beggar by the multiplex. Is (A) the (C) an (B) a (D) nil

Q.14

The article required before the word University in the sentence She met Professor Shah at ..........................University is (A) a (C) the (B) an (D) nil

Q.15

Which one is the correct sentence amongst the following sentences?

(A) Mr. Gupta, accompanied by his friends, were assembled on the lawns. (B) Mr. Gupta, accompanied by his friends, are assembled on the lawns. (C) Mr. Gupta, accompanied by his friends, assembled on the lawns. (D) Mr. Gupta, accompanied by his friends, have assembled on the lawns.

JTO

27/28

JTO Telecom 2009

Q.16

[Link]

JTO

Who was the first woman to be elected as the President of the Indian National Congress? (A) Sarojini Naidu (C) Indira Gandhi (B) Sonia Gandhi (D) Annie Besant

Q.17

Which political leader delivered the famous I have a dream speech? (B) Winston Churchill (D) Rabindranath Tagore

(A) Jawaharlal Nehru (C) Martin Luther King

Q.18

Who established the organization Khudai Khidmatgar (B) Gopal Krishna Gokhale (D) Khan Abdul Ghaffar Khan

(A) Hyder Ali (C) Maulana Abul Kalam Azad

Q.19

Analgesics are drugs used to prevent or relieve (B) fever and high body temperature (D) stress and anxiety

(A) aches and pain (C) hormone deficiency The abbreviation CD stands for

Q.20

(A) Circular Disc (C) Compact Disc

(B) Computer Device (D) Code-Demodulator

**********

JTO

28/28